Acrydur 528 ENG US 21 10 2022

Acrydur™ - 528 N (USA)
Medium viscous PU-MMA resin for sealcoats of

Acrydur™ Coatings based on Acrydur™ 332 N.
Particularly suitable for outside applications
Characteristics: Flexible topcoat, high impact strength especially on broadcast

Acrydur™ 332 N outdoor coatings. The coating remains impact
resistant even in a wide range of varying temperatures.
Acrydur™ 528 is also suitable as a sealer in freezer rooms.
Characteristic data:
Delivery form liquid, blue

Flow time 25 - 32 sec (68°F) DIN flow cup, 4mm
Curing 25-35 min (68°F)
Shelf life In the original container, dark at < 65°F
maximum 6 months
Bundle 396.83 lb drums
55.12 lb, 22.05 lb pails
Initiator/Hardener: Hardener Powder (BPO), temperature-dependent
Processing Notes:
Processing: For proper curing at least 14.11 ounce/ft2 sealer must be applied
per rolling step. In order to ensure the necessary slip resistance
and to avoid yellowing and flaking, the maximum layer thickness
is limited to 28.22 ounce/ ft2. Best results are obtained with 24.69
ounce/ ft2 by roller step with short hair (polyamide gold stripe) on
sand broadcast coatings (15 - 30 mesh grain).
Scratch and water resistance can be ameliorated by using

Hardener M. Acrydur™ Hardener M leads to a mat surface.
Please mind the indications on the product data sheet.
Suggested
formulation: 2.113 gal Acrydur™ 522 N
2.71 oz Hardener 50 W or 5.41 oz Hardener M
Pot life and curing

07-06-2022 1 /3
Plasti Chemie Produktionsgesellschaft mbH Telefon: +49 (0) 37 45 / 744 32-0 Email: info@plasti-chemie.de
Falgardring 1 Telefax: +49 (0) 37 45 / 744 32-27 Internet: www.plasti-chemie.de
D – 08223 Falkenstein / Germany
times depending
on temperature: Further coating layers with Acrydur™ must only be applied after
the previous layers have completely cured.
*) Hardener quantity referred to Plastifloor® 528
(Hardener 50W) Temperature Hardener Pot life Curing time
[°F]** [Vol%]* [min] [min]
+41 2 ca. 30 ca. 50
+50 1,5 ca. 20 ca. 40
+68 1 ca. 15 ca. 30
+77 1 ca. 12 ca. 20
**) Temperature specifications refer to resin -, soil
and temperature.
*) Hardener quantity referred to Acrydur™ 528 (Hardener 50W)

**) Temperature specifications refer to resin -, soil and temperature.
Attention: At temperatures below 32 °F, the resin needs to be put into a

warm environment before processing - minimum 41 °F and add
up to 2% hardener maximum. Basically accelerator cannot be
added to sealings – neither as thinner nor as accelerator – due
to yellowing aspects.
Storage: The handling-regulations for highly flammable materials apply to

methacrylate – resins. Acrydur™ resins are to be stored cool,
protected against direct sunlight and preferably at temperatures
of 59 - 68 °F. During storage paraffin – particles and filler –
materials may precipitate. Thus before processing, containers
have to be stirred up well. Please mind the advice on our safety
data sheets.
Industrial safety:
Ensure sufficient ventilation during work. On processing, pay

attention to the directives in the hazardous substances ordinance
and to the indications of the Federal States Committee for
industrial safety and safety engineering (LASI) as well as to our
safety date sheets.
VbF: AI
GISCODE: RMA 10
07-06-2022 2 /3
Taxnumber: 3208 2010
Data concerning our products and devices as well as concerning our data and procedures are based on an
extensive research work and an application technology experience. We obtain these results, with which we do not
take over adhesion going beyond the respective single contract, in word and writing after best knowledge, reserve
ourselves we however technical changes in the course of the product development. Beyond that our application
technology service stands when desired for large consultation as well as for co-operation with the solution
manufacturing and application technology problems for order. That does not relieve the user however to examine
our data and recommendations before their use responsible for the own use. That applies - particularly for deliveries
to foreign markets - also regarding the keeping of patent rights third as well as for applications and procedures,
which are not expressly in writing indicated by us. The case of loss our adhesion is limited to indemnifications of
same extent, as they plan our general terms of delivery and sales with lack of quality.
07-06-2022 3 /3

Acrydur 528 ENG US 21 10 2022

Uploaded by

Copyright:

Available Formats

Acrydur 528 ENG US 21 10 2022

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Acrydur 528 ENG US 21 10 2022

Uploaded by

Copyright:

Available Formats

Acrydur™ - 528 N (USA)

Medium viscous PU-MMA resin for sealcoats of

Characteristics: Flexible topcoat, high impact strength especially on broadcast

Delivery form liquid, blue

Initiator/Hardener: Hardener Powder (BPO), temperature-dependent

Scratch and water resistance can be ameliorated by using

Pot life and curing

*) Hardener quantity referred to Acrydur™ 528 (Hardener 50W)

Attention: At temperatures below 32 °F, the resin needs to be put into a

Storage: The handling-regulations for highly flammable materials apply to

Ensure sufficient ventilation during work. On processing, pay

Taxnumber: 3208 2010

You might also like