Basic Electronics4 - 1-1-1-1-1

SCHOOL OF ENGINEERING
DEPARTMENT OF ELECTRICAL & COMMUNICATIONS

ENGINEERING
ECE 281 BASIC ELECTRONICS (3 units)
Course Content
Introduction to semi-conductors and diodes:

Characteristics of the p-n junction, p-n-junction diodes. Zener diodes. Rectification, other
semiconductor diode applications
Bipolar junction transistors:
Bipolar Junction Transistor characteristics and biasing. Equivalent circuits of Bipolar
Junction Transistors. Bipolar Junction Transistor amplifiers (Common Base; Common
Emitter; Common Collector).
Field Effect Transistors:
Junction Field Effect Transistors and Metal Oxide Semiconductor Field Effect Transistors.
Biasing and equivalent circuits of Field Effect Transistors. Field Effect Transistors
amplifiers: Common Gate, Common Source Common Drain.
References
Malvino P. A, Electronic Principles, McGraw Hill 1999
The Art of Electronics by Paul Horowitz and Winfield Hill (1989)
Electronics (Wiley Self-Teaching Guides) by Harry Kybett (1986)
Course Lecturer: Dr. E. Ataro (Academic year 2011/2012)
ECE 281 BASIC ELECTRONICS (2011/2012) 1

CHAPTER 1
CONDUCTION IN SEMICONDUCTORS
Electrons and holes in an intrinsic semiconductors, conductivity of a semiconductor,

carrier concentrations in an intrinsic semiconductor, donor and acceptor impurities,
charge densities in a semiconductor, Fermi level in a semiconductor having impurities,
diffusion, carrier life time, Hall effect. (Covered in ECE 152 EE Materials)
The branch of engineering which deals with the flow of Electrons through vacuum,
gas or semiconductor is called Electronics.
Electronics essentially deals with electronic devices and their utilization.
Atomic Structure
• Atom is the basic building block of all the elements. It consists of the central
nucleus of positive charge around which small negatively charged particles called
electrons revolve in different paths or orbits.
• An Electrostatic force of attraction between electrons and the nucleus holds up

electrons in different orbits.
Electrostatic force.
+
Centrifugal force.
Figure1.1. Atomic structure

• Nucleus is the central part of an atom and contains protons and neutrons. A proton
is positively charged particle, while the neutron has the same mass as the proton,
but has no charge. Therefore, the nucleus of an atom is positively charged.
• atomic weight = no. of protons + no. of neutrons
• An electron is a negatively charged particle having negligible mass. The charge

on an electron is equal but opposite to that on a proton. Also the number of
electrons is equal to the number of protons in an atom under ordinary conditions.
Therefore an atom is neutral as a whole.
• atomic number = no. of protons or electrons in an atom
• The number of electrons in any orbit is given by 2n2 where n is the number of the
orbit.
For example, orbit I contains 2x12 =2 electrons
orbit II contains 2x22 = 8 electrons
orbit III contains 2x32 = 18 electrons and so on
• The last orbit cannot have more than 8 electrons.
• The orbit preceding the last one cannot have more than 18 electrons.
Positive and negative ions
• Protons and electrons are equal in number hence if an atom loses an electron it
has lost negative charge therefore it becomes positively charged and is referred as
positive ion.
• If an atom gains an electron it becomes negatively charged and is referred to as

negative ion.
Valence electrons
The electrons in the outermost orbit of an atom are known as valence electrons.
• The outermost orbit can have a maximum of 8 electrons.
• The valence electrons determine the physical and chemical properties of a

material.

• When the number of valence electrons of an atom is less than 4, the material is
usually a metal and a conductor. Examples are sodium, magnesium and
aluminium, which have 1, 2 and 3 valence electrons respectively.
• When the number of valence electrons of an atom is more than 4, the material is
usually a non-metal and an insulator. Examples are nitrogen, sulphur and neon,
which have 5, 6 and 8 valence electrons respectively.
• When the number of valence electrons of an atom is 4 the material has both metal
and non-metal properties and is usually a semi-conductor. Examples are carbon,
silicon and germanium.
Free electrons
• The valence electrons of different material possess different energies. The greater
the energy of a valence electron, the lesser it is bound to the nucleus.
• In certain substances, particularly metals, the valence electrons possess so much

energy that they are very loosely attached to the nucleus.
• The loosely attached valence electrons move at random within the material and
are called free electrons.
The valence electrons, which are loosely attached to the nucleus, are known as free
electrons.
Energy bands
• In case of a single isolated atom an electron in any orbit has definite energy.
• When atoms are brought together as in solids, an atom is influenced by the forces
from other atoms. Hence an electron in any orbit can have a range of energies
rather than single energy. These ranges of energy levels are known as Energy
bands.
• Within any material there are two distinct energy bands in which electrons may
exist viz. valence band and conduction band.

Energy level Conduction band
Forbidden gap
Valence band
Figure1.2 Energy level diagram
• The range of energies possessed by valence electrons is called valence band.
• The range of energies possessed by free electrons is called conduction band.
• Valence band and conduction band are separated by an energy gap in which no
electrons normally exist this gap is called forbidden gap.
Electrons in conduction band have either escaped from their atoms (free electrons) or
only weakly held to the nucleus. Thereby the electrons in conduction band may be easily
moved around within the material by applying relatively small amount of energy (either
by increasing the temperature or by focusing light on the material etc.) This is the reason
why the conductivity of the material increases with increase in temperature.
But much larger amounts of energy must be applied in order to extract an electron from
the valence band because electrons in the valence band are usually in the normal orbit
around a nucleus. For any given material, the forbidden gap may be large, small or non-
existent.
Classification of materials based on Energy band theory
Based on the width of the forbidden gap, materials are broadly classified as conductors,
Insulators and semiconductors.
Conduction Conduction
Conduction band band
band
Forbidden
overlap Gap Forbidden
EG >5eV Gap EG ≈1eV
Valence Valence Valence

band band band
(a) Conductor (b) Insulator (c) Semiconductor

Conductors
• Conductors are those substances, which allow electric current to pass through
them.
Example: Copper, Aluminium, salt solutions, etc.
• In terms of energy bands, conductors are those substances in which there is no

forbidden gap. The valence and conduction bands overlap as shown in fig (a).
• For this reason, a very large number of electrons is available for conduction even
at extremely low temperatures. Thus, conduction is possible even by a very weak
electric field.
Insulators
• Insulators are those substances, which do not allow electric current to pass
through.
Example: Phosphorus, sulphur, arsenic, (Rubber, glass, wood) etc.
• In terms of energy bands, insulators are those substances in which the forbidden
gap is very large.
• Thus valence and conduction band are widely separated as shown in fig (b).
Therefore insulators do not conduct electricity even with the application of a large
electric field or by heating or at very high temperatures.
Semiconductors
• Semiconductors are those substances whose conductivity lies in between that of a

conductor and Insulator.
Example: Silicon, germanium, Gallium Arsenide, Indium Phosphide, etc.
• In terms of energy bands, semiconductors are those substances in which the

forbidden gap is narrow (in the order of 1 eV).
• Thus valence and conduction bands are moderately separated as shown in fig (c).
• In semiconductors, the valence band is partially filled, the conduction band is also
partially filled, and the energy gap between conduction band and valence band is
narrow.
• Therefore, comparatively smaller electric field is required to push the electrons

from valence band to conduction band. At low temperatures the valence band is
completely filled and conduction band is completely empty. Therefore, at very
low temperature a semi-conductor actually behaves as an insulator.

Conduction in solids
• Conduction in any given material occurs when a voltage of suitable magnitude is

applied to it, which causes the charge carriers within the material to move in a
desired direction.
• This may be due to electron motion or hole transfer or both.
Electron motion
Free electrons in the conduction band move under the influence of an applied electric
field. Since electrons have negative charge they are repelled by the negative terminal of
the applied voltage and attracted towards the positive terminal.
Hole transfer
• Hole transfer involves the movement of holes.

• Holes may be thought of as positive charged particles and as such they move
through an electric field in a direction opposite to that of electrons.
I I
+ +
V V
(a) Conductor (b) Semiconductor
Flow of electrons Flow of electrons
Flow of current (conventional) Flow of holes

Flow of current
• In a good conductor (metal) as shown in fig (a) the current flow is due to free
electrons only.
• In a semiconductor as shown in fig (b). The current flow is due to both holes and
electrons moving in opposite directions.
• The unit of electric current is Ampere (A) and since the flow of electric current is
constituted by the movement of electrons in conduction band and holes in valence
band, electrons and holes are referred as charge carriers.

Classification of semiconductors
Semiconductors are classified into two types.
a) Intrinsic semiconductors.
b) Extrinsic semiconductors.
a) Intrinsic semiconductors
• A semiconductor in an extremely pure form is known as intrinsic

semiconductor.
Example: Silicon, germanium.
• Both silicon and Germanium are tetravalent (having 4 valence electrons).
• Each atom forms a covalent bond or electron pair bond with the electrons of
neighboring atom. The structure is shown below.
Silicon or Germanium
Valence electron
Covalent bond
Figure1.3. Crystalline structure of Silicon (or Germanium)
At low temperature
• At low temperature, all the valence electrons are tightly bounded the nucleus
hence no free electrons are available for conduction.
• The semiconductor therefore behaves as an insulator at absolute zero

temperature.

At room temperature
Free electron
Valence electron
Holes
Figure 1.4. Crystalline structure of Silicon (or Germanium) at room temperature
• At room temperature, some of the valence electrons gain enough thermal energy
to break up the covalent bonds.
• This breaking up of covalent bonds sets some electrons free and available for
conduction.
• When an electron escapes from a covalent bond and becomes free, a vacancy is
created in a covalent bond as shown in figure 1.4 above. Such a vacancy is called
a hole. It carries a positive charge and moves under the influence of an electric
field in the direction of the electric field applied.
• Numbers of holes is equal to the number of free electrons since, a hole is nothing
but an absence of electrons in a covalent bond.
Extrinsic Semiconductor
• When an impurity is added to an intrinsic semiconductor its conductivity changes.
• This process of adding impurity to a semiconductor is called doping and the

impure semiconductor is called an extrinsic semiconductor.
• Depending on the type of impurity added, extrinsic semiconductors are further

classified as n-type and p-type semiconductors.

n-type semiconductor
Si Si Si
free e-
Si As Si
Si Si Si
Figure 1.5 n-type semiconductor
Conduction band
Forbidden gap Fermi level
Valence band
Figure1.6 Energy band diagram for n-type semiconductor
• When a small current of a Pentavalent impurity is added to a pure

semiconductor it is called as n-type semiconductor.
• Addition of Pentavalent impurity provides a large number of free electrons in a

semiconductor crystal.
• Typical examples for pentavalent impurities are Arsenic, Antimony and

Phosphorus etc. Such impurities which produce n-type semiconductors are known
as Donor impurities because they donate or provide free electrons to the
semiconductor crystal.
• To understand the formation of n-type semiconductor, consider a pure silicon

crystal with impurity say arsenic added to it as shown in figure 1.5.

• We know that a silicon atom has 4 valence electrons and Arsenic has 5 valence
electrons. When Arsenic is added as impurity to silicon, the 4 valence electrons of
silicon make covalent bond with 4 valence electrons of Arsenic.
• The 5th valence electrons finds no place in the covalent bond thus, it becomes free
and travels to the conduction band as shown in figure. Therefore, for each arsenic
atom added, one free electron will be available in the silicon crystal. Though each
arsenic atom provides only one free electron, an extremely small amount of
arsenic impurity provides enough atoms to supply millions of free electrons.
Due to thermal energy, election-hole pairs are still generated but the number of free
electrons is very large compared to holes. So in an n-type semiconductor electrons are the
majority charge carriers and holes the minority charge carriers. Since the current
conduction is pre-dominantly by free electrons (-vely charges) it is called as n-type
semiconductor (n- means –ve).
p-type semiconductor
Si Si Si
hole
Si Ga Si
Si Si Si
Figure 1.7 p-type semiconductor

Conduction band
Forbidden gap Fermi level
Valence band
Figure 1.8 Energy band diagram for p-type semiconductor
• When a small amount of trivalent impurity is added to a pure semiconductor

it is called p-type semiconductor.
• The addition of trivalent impurity provides large number of holes in the

semiconductor crystals.
• Example: Gallium, Indium or Boron etc. Such impurities which produce p-type
semiconductors are known as acceptor impurities because the holes created can
accept electrons in the semiconductor crystal.
To understand the formation of p-type semiconductor, consider a pure silicon crystal with
an impurity say gallium added to it as shown in figure 1.7.
• We know that silicon atom has 4 valence electrons and Gallium has 3 electrons.
When Gallium is added as impurity to silicon, the 3 valence electrons of gallium
make 3 covalent bonds with 3 valence electrons of silicon.
• The 4th valence electrons of silicon cannot make a covalent bond with that of
Gallium because of short of one electron as shown above. This absence of
electron is called a hole. Therefore for each gallium atom added one hole is
created. A small amount of Gallium provides millions of holes.
Due to thermal energy, electron-hole pairs are still generated but the number of holes is
very large compared to that of electrons. Therefore, in a p-type semiconductor holes are
majority carriers and electrons the minority carriers. Since the current conduction is
predominantly by holes (+ charges) it is called as p-type semiconductor (p means +ve)

Drift and Diffusion current
The flow of current through a semiconductor material is normally referred to as one of

the two types.
Drift current
• If an electron is subjected to an electric field in free space it will accelerate in a
straight line form the –ve terminal to the + ve terminal of the applied voltage.
• However in the case of conductor or semiconductor at room temperature, a free

electrons under the influence of electric field will move towards the +ve terminal
of the applied voltage but will continuously collide with atoms all the ways as
shown in figure 1.9.
Electron drift due to E-field
conduction
when electric
field is
semiconductor
present
+
Conduction
Applied voltage when no electric
field is applied
Figure 1.9
• Each time, when the electron strikes an atom, it rebounds in a random direction
but the presence of electric field does not stop the collisions and random motion.
As a result the electrons drift in a direction of the applied electric field.
• The current produced in this way is called as Drift current and it is the usual kind
of current flow that occurs in a conductor.
Diffusion current
• The directional movement of charge carriers due to their concentration

gradient produces a component of current known as Diffusion current.
• The mechanism of transport of charges in a semiconductor when no electric field

is applied called diffusion. It is encountered only in semiconductors and is
normally absent in conductors.

heavy concentration of less concentration
electrons electrons
Diffusion current
Even distribution
Net diffusion current is zero
• With no voltage is applied, if the number of charge carriers (either holes or

electrons) in one region of a semiconductor is less compared to the rest of the
region then there exist a concentration gradient.
• Since the charge carriers are either all electrons or all holes they have polarity of
charge and thus there is a force of repulsion between them.
• As a result, the carriers tend to move gradually or diffuse from the region of
higher concentration to the region of lower concentration. This process is called
diffusion and electric current produced due to this process is called diffusion
current.
• This process continues until all the carriers are evenly distributed through the
material. Hence when there is no applied voltage, the net diffusion current will be
zero.

Fermi-level
Fermi level indicates the level of energy in the forbidden gap.
1. Fermi-level for an Intrinsic semiconductor
Conduction band
Energy level
EC
Ef Fermi level
Forbidden gap
EV
Valence band
EC Conduction band energy edge
EV Valence band energy edge
Ef Fermi level
Figure 1.10 Energy level diagram for intrinsic semiconductor
• We know that the intrinsic semiconductor acts as an insulator at absolute zero

temperature because there are free electrons and holes available but as the
temperature increases electron hole pairs are generated and hence number of
electrons will be equal to number of holes.
• Therefore, the possibility of obtaining an electron in the conduction band will be

equal to the probability of obtaining a hole in the valence band.
• If EC is the lowest energy level of conduction band and EV is the highest energy
level of the valence band then the Fermi level Ef is exactly at the centre of these
two levels as shown above.

2. Fermi-level in a semiconductors having impurities (Extrinsic)
a) Fermi-level for n-type Semiconductor
• Let a donor impurity be added to an intrinsic semiconductor then the

introduced donor energy level (ED) shown by the dotted lines is very close
to conduction band energy level (EC).
• Therefore the unbonded valence electrons of the impurity atoms can very
easily jump into the conduction band and become a free electron, thus at
room temperature, almost all the extra electrons of pentavalent impurity
will jump to the conduction band.
• The donor energy level (ED) is just below conduction band level (EC) as
shown in figure1.10 (a). Due to a large number of free electrons, the
probability of electrons occupying the energy level towards the conduction
band will be more hence, Fermi level shifts towards the conduction band.
Conduction band
EC
ED
moves Fermi level Ef
upward
EV
Valence band
ED Energy level of donor impurity
Figure 1.10 (a) Energy level diagram for n-type semiconductor

b) Fermi-level for P-type semiconductor
• Let an acceptor impurity be added to an intrinsic semiconductor, then the acceptor

energy level (EA) shown by dotted lines is very close to the valence band energy
level (EV).
• Therefore the valence band electrons of the impurity atom can very easily jump
into the new valence band level thereby creating holes in the valence band.
Conduction band
EC
Fermi level Ef
EA
EV
Valence band
EA Energy level of acceptor impurity
Figure 1.11 (b) Energy level diagram for P-type semiconductor
• The acceptor energy level (EA) is just above the valence band level as shown in
figure 1.11 (b).
• Due to large number of holes the probability of holes occupying the energy level
towards the valence band will be more and hence, the Fermi level gets shifted
towards the valence band.

HALL EFFECT
If a piece of metal or semiconductor carrying a current I is placed in a transverse

magnetic field B then an electric field E is induced in the direction perpendicular to both I
and B. This phenomenon is known as Hall Effect.
Y(+ve)
Surface-2
+ + + + + + + +
d
I VH
w
X (+ve)
B
Surface -1
Z (+ve)
Figure 1.12. Illustration of the Hall Effect
Hall Effect is normally used to determine whether a semi-conductor is n-type or p-type.
To find whether the semiconductor is n-type or p-type
i) In Figure 1.12 above, if I is in the +ve X direction and B is in the +ve Z

direction, then a force will be exerted on the charge carriers (holes and
electrons) in the –ve Y direction.
ii) This force is independent of whether the charge carriers are electrons or holes.
Due to this force the charge carriers (holes and electrons) will be forced
downward towards surface –1 as shown. (Note: this happens because the
charge carriers are oppositely charged and move in opposite directions.
iii) If the semiconductor is n-type, then electrons will be the charge carriers and
these electrons will accumulate on surface –1 making that surface –vely
charged with respect to surface –2. Hence a potential called Hall voltage
appears between the surfaces 1 and 2.
iv) Similarly when surface –1 is positively charged with respect to surface –2,
then the semiconductor is of p-type. In this way, by seeing the polarity of Hall
voltage we can determine whether the semiconductor is of p-type or n-type.

Applications of Hall Effect
Hall Effect is used to determine,
• carrier concentration, conductivity and mobility.

• the sign of the current carrying charge carriers.
• charge density.
• used as magnetic field meter.
Carrier lifetime (τ)
In a pure semiconductor, we know that number of holes is equal to the number of

electrons. Thermal agitation however, continues to produce new electron-hole pairs while
other electron-hole pairs disappear as a result of recombination.
On an average, a hole will exist for τp seconds and an electron will exist for τn seconds
before recombination. This time is called the carrier lifetime or mean lifetime.
The average time an electron or hole can exist in the free state is called carrier lifetime.

CHAPTER 2
SEMICONDUCTOR DIODE
When a p-type semiconductor material is suitably joined to n-type semiconductor the
contact surface is called a p-n junction. The p-n junction is also called as semiconductor
diode.
p n
++
(b)
(a) Depletion region
Fig. 2.0 (a) p-n junction Fig 2.0 (b) Symbolic representation
• The left side material is a p-type semiconductor having –ve acceptor ions and
+vely charged holes. The right side material is n-type semiconductor having +ve
donor ions and free electrons.
• Suppose the two pieces are suitably treated to form p-n junction, then there is a
tendency for the free electrons from n-type to diffuse over to the p-side and holes
from p-type to the n-side. This process is called diffusion.
• As the free electrons move across the junction from n-type to p-type, +ve donor
ions are uncovered. Hence a +ve charge is built on the n-side of the junction. At
the same time, the free electrons cross the junction and uncover the –ve acceptor
ions by filling in the holes. Therefore a net –ve charge is established on p-side of
the junction.
• When a sufficient number of donor and acceptor ions is uncovered further

diffusion is prevented.
• Thus a barrier is set up against further movement of charge carriers. This is called
potential barrier or junction barrier VO. The potential barrier is of the order of 0.1
to 0.7V.
Note: outside this barrier on each side of the junction, the material is still neutral. Only
inside the barrier, there is a +ve charge on n-side and –ve charge on p-side. This region is
called depletion layer.

2.1 Biasing: Connecting a p-n junction to an external d.c. voltage source is called
biasing.
(i) Forward biasing

(ii) Reverse biasing
(i) Forward biasing
• When external voltage applied to the junction is in such a direction that it cancels
the potential barrier, thus permitting current flow is called forward biasing.
• To apply forward bias, connect +ve terminal of the battery to p-type and –ve
terminal to n-type as shown in fig.2.1 below.
• The applied forward potential establishes the electric field which acts against the
field due to potential barrier. Therefore the resultant field is weakened and the
barrier height is reduced at the junction as shown in fig. 2.1.
• Since the potential barrier voltage is very small, a small forward voltage is
sufficient to completely eliminate the barrier. Once the potential barrier is
eliminated by the forward voltage, junction resistance becomes almost zero and a
low resistance path is established for the entire circuit. Therefore current flows in
the circuit. This is called forward current.
p n
no external field
External field
Fig.2.1 Forward biasing of p-n junction

(ii) Reverse biasing
• When the external voltage applied to the junction is in such a direction the
potential barrier is increased it is called reverse biasing.
• To apply reverse bias, connect –ve terminal of the battery to p-type and +ve
terminal to n-type as shown in figure below.
• The applied reverse voltage establishes an electric field which acts in the same
direction as the field due to potential barrier. Therefore the resultant field at the
junction is strengthened and the barrier height is increased as shown in fig.2.2.
• The increased potential barrier prevents the flow of charge carriers across the
junction. Thus a high resistance path is established for the entire circuit and hence
current does not flow.
p n
external e-field
no external e-field
Fig.2.2 Reverse biasing of p-n junction

2.2 Volt- Ampere characteristics(V-I)
A
diode
V V
(i)
IF(mA)
Breakdown
Voltage
VR Knee voltage VF
IR(µA)
(ii)
Fig. 2.3 Circuit diagram and I-V characteristic of p-n junction diode
(i) Circuit diagram
(ii) Characteristic
• The I-V characteristics of a semiconductor diode can be obtained with the help of
the circuit shown in fig. 2.3 (i)
• The supply voltage V is a regulated power supply, the diode is forward biased in
the circuit shown. The resistor R is a current limiting resistor. The voltage across
the diode is measured with the help of voltmeter and the current is recorded using
an ammeter.
• By varying the supply voltage different sets of voltage and currents are obtained.
By plotting these values on a graph, the forward characteristics can be obtained.
It can be noted from the graph the current remains zero (almost) till the diode
voltage attains the barrier potential.
• For silicon diode, the barrier potential is 0.7 V and for Germanium diode, it is 0.3
V. The barrier potential is also called as knee voltage or cut-in voltage.

• The reverse characteristics can be obtained by reverse biasing the diode. It can be
noted that at a particular reverse voltage, the reverse current increases rapidly.
This voltage is called breakdown voltage.
2.3 Diode current equation
The current in a diode is given by the diode current equation
I = I0( e V/ηVT –1)
where, I diode current

I0 reverse saturation current
V diode voltage
η semiconductor constant
=1 for Ge, 2 for Si.
VT Voltage equivalent of temperature= kT/e= T/11,600 (Temperature T in
Kelvin, k is Boltzman constant, e is charge on electron)
Note: If the temperature is given in 0C then it can be converted to Kelvin by the help of
following relation, 0C+273 = K
2.4 Diode equivalent circuit
It is generally profitable to replace a device or system by its equivalent circuit. Once the
device is replaced by its equivalent circuit, the resulting network can be solved by
traditional circuit analysis technique.
switch rf
If
VF Vo
VF
(i) (ii )
Fig.2.4 Diode equivalent circuit. (i) symbol (ii) equivalent circuit
The forward current If flowing through the diode causes a voltage drop in its internal
resistance rf. Therefore the forward voltage VF applied across the actual diode has to
overcome
1. potential barrier VO
2. internal drop If rf
Vf = VO + If rf
For silicon diode VO = 0.7V whereas for Germanium diode VO = 0.3 V.

For ideal diode rf =0.
2.4.1 Basic Diode Definitions
1. Knee voltage or Cut-in Voltage.

It is the forward voltage at which the diode starts conducting.
2. Breakdown voltage
It is the reverse voltage at which the diode (p-n junction) breaks down with sudden rise in
reverse current.
3. Peak-inverse voltage (PIV)

It is the maximum reverse voltage that can be applied to a p-n junction without causing
damage to the junction.
If the reverse voltage across the junction exceeds its peak-inverse voltage, then the
junction exceeds its Peak-inverse voltage, then the junction gets destroyed because of
excessive heat. In rectification, one thing to be kept in mind is that care should be taken
that reverse voltage across the diode during –ve half cycle of a.c. does not exceed the
peak-inverse voltage of the diode.
4. Maximum Forward current

It is the maximum instantaneous forward current that a p-n junction can conduct without
damaging the junction. If the forward current is more than the specified rating then the
junction gets destroyed due to over heating.
5. Maximum Power rating

It is the maximum power that can be dissipated at the junction without damaging it. The
power dissipated across the junction is equal to the product of junction current and the
voltage across the junction.
6. Transition or Depletion Capacitance

The typical amount of capacitance intrinsic to the junction, due to the depletion region
acting as a dielectric separating the anode and cathode connections. This is usually a very
small figure, measured in the range of picofarads (pF). Effect used in varactor diode.
7. Storage or Diffusion Capacitance

Results from majority carriers that cross the junction during forward bias. On suddenly
reverse biasing the diode, these carriers take time to clear from both sides – producing a
capacitive effect.
8. Reverse recovery time

the amount of time it takes for a diode to “turn off ” when the voltage across it alternates
from forward-bias to reverse-bias polarity. Ideally, this figure would be zero: the diode
halting conduction immediately upon polarity reversal. For a typical rectifier diode,
reverse recovery time is in the range of tens of microseconds; for a “fast switching”
diode, it may only be a few nanoseconds.

2.5 RECTIFIERS
“Rectifiers are the circuit which converts a.c. to d.c.”
Rectifiers are grouped into two categories depending on the cycles of conduction in one
period, namely;
1. Half-wave rectifier
2. Full- wave rectifier.
2.5.1 Half-wave rectifier

The circuit diagram of a half-wave rectifier is shown in fig. 2.5 below along with the I/P
and O/P waveforms.
(i)
Vi
Vo
π 2π t
(ii)
Fig. 2.5 Half wave rectifier (i) Circuit diagram (ii) input and output waveforms
• The transformer is employed in order to step-down the supply voltage to the

appropriate desired voltage.
• The diode is used to rectify the a.c. signal while, the pulsating d.c. is taken across
the load resistor RL.

• During the +ve half cycle, the end X of the secondary is +ve and end Y is -ve .
Thus , forward biasing the diode. As the diode is forward biased, the current flows
through the load RL and a voltage is developed across it.
• During the –ve half-cycle the end Y is +ve and end X is –ve thus, reverse biasing
the diode. As the diode is reverse biased there is no flow of current through RL
thereby the output voltage is zero.
2.5.2 Efficiency of a rectifier

The ratio of d.c. power to the applied input a.c. power is known as rectifier efficiency.
d .c. power.output
Rectifier efficiency η =
input.a.c. power
2.5.3 Derivation of rectifier efficiency of Half wave rectifier
Let V = Vmsin t be the voltage across the secondary winding

rf = diode resistance
RL = load resistance
d.c. power
π π
1 1 Vm Sin.t
2π ∫0 2π ∫0 rL + RL
I av = I dc = i.dt = dt
π
Vm
2π (r f + R L ) ∫0
= Sin.t.dt
2Vm I
= = m
2π (rf + RL ) π
d.c. power Pdc = I2dc * RL

2
 Im 
=   ∗ RL (1)
π 

a.c. power input
The a.c. power input is given by Pac = I2rms ( rf + RL)
2π
1
I rms =
2π 0∫ i 2 dt (The RMS value is the effective value of an alternating
voltage or current. It is the equivalent steady dc (constant) value which gives the same
effect.)
Squaring both sides we get
2π
1
= ∫i
2 2
I dt
2π
rms
0
But i = Im Sin.t
π
1
2π ∫0
I 2
rms = ( I m Sin.t ) 2 dt (current flows through diode only for duration 0 to Π)
I m2
2
I rms =
4
Im
I rms =
2
2
I 
∴ Pac =  m  (r f + RL ) (2)
 2 
2
 Im 
Pdc  π
∴η = =   * RL
Pac  I m  2 (r f + RL )
 2
 
0.406
η = (3)
rf
1+
RL
The efficiency is maximum if rf is negligible as compared to RL

Therefore maximum rectifier efficiency = 40.6 %
2.5.4 Full-wave rectifier
Full-wave rectifiers are of two types
1. Centre-tapped full-wave rectifier

2. Bridge rectifier
2.5.4.1 Centre-tapped full –wave rectifier
(i)
Vin
Vout
π 2π
(ii)
Fig. 2.6 Centre-tapped Full wave rectifier (i) Circuit diagram (ii) waveforms
• The circuit diagram of a centre-tapped full wave rectifier is shown in fig. 2.6
above. It employs two diodes and a centre-tap transformer. The a.c. signal to be
rectified is applied to the primary of the transformer and the d.c. output is taken
across the load RL.

• During the +ve half-cycle end X is +ve and end Y is –ve this makes diode D1
forward biased and thus a current i1 flows through it and load resistor RL.Diode
D2 is reverse biased and the current i2 is zero.
• During the –ve half-cycle end Y is +Ve and end X is –Ve. Now diode D2 is
forward biased and thus a current i2 flows through it and load resistor RL. Diode
D1 is reversed and the current i1 = 0.
Disadvantages
• Since, each diode uses only one-half of the transformer secondary voltage the d.c.
output is comparatively small.
• It is difficult to locate the centre-tap on secondary winding of the transformer.
• The diodes used must have high Peak-inverse voltage.
2.5.4.2 Bridge rectifier
(i)
Vout
D1D3 D2D4 D1D4
(ii)
Fig. 2.7 Full wave bridge wave rectifier (i) Circuit diagram (ii) output waveform.
• The circuit diagram of a bridge rectifer is shown above. It uses four diodes and a
transformer.

• During the +ve half-cycle, end A is +ve and end B is –ve thus diodes D1 and D3
are forward bias while diodes D2 and D4 are reverse biased thus a current flows
through diode D1, load RL ( C to D) and diode D3.
• During the –ve half-cycle, end B is +ve and end A is –ve thus diodes D2 and D4
are forward biased while the diodes D1 and D3 are reverse biased. Now the flow
of current is through diode D4 load RL (D to C) and diode D2. Thus, the waveform
is same as in the case of centre-tapped full wave rectifier.
Advantages
• The need for centre-taped transformer is eliminated.

• The output is twice when compared to centre-tapped full wave rectifier for the
same secondary voltage.
• The peak inverse voltage is one-half (1/2) compared to centre-tapped full wave
rectifier.
• Can be used where large amount of power is required.
Disadvantages
• It requires four diodes.

• The use of two extra diodes cause an additional voltage drop thereby reducing the
output voltage.
2.5.6 Efficiency of Full-wave rectifier
Let V = Vmsint be the voltage across the secondary winding

I = Imsint be the current flowing in secondary circuit
rf = diode resistance
RL = load resistance
d.c. power output

Pdc = I dc2 RL (1)
π
1
2π ∫0
I dc = I av =2 i.dt
π
1
2π ∫0
I av =2 Im Sin.t.dt
2I m
I av = (2)
π

2
 2I  (3)
∴ Pdc =  m  RL
 π 
input a.c. power
Pac = I rms
2
(r f + RL ) (4)
π
1 2
2π ∫0
I rms = 2 i dθ
Squaring both sides we get
π
1
π∫
I 2
rms = i 2
dθ
0
π
1
= ∫ (Im Sinθ ) dθ
2 2
I rms
π 0
I m2
I 2
rms =
2
Im
I rms = (5)
2
2
I 
∴ Pac =  m  (r f + R L ) (6)
 2
2
 2I m 
Pdc  π  RL
∴η = =  *
Pac  I m 
2
(r f + RL )
 
 2
0.812
η = (7)
rf
1+
RL
The efficiency will be maximum if rf is negligible as compared to RL.
Maximum efficiency = 81.2 %

This is the double the efficiency due to half wave rectifier. Therefore a Full-wave
rectifier is twice as effective as a half-wave rectifier.
2.6 Ripple factor
The pulsating output of a rectifier consists of d.c. component and a.c. component (also
known as ripple). The a.c. component is undesirable and account for the pulsations in the
rectifier output. The effectiveness of a rectifier depends upon the magnitude of a.c.
component in the output: the smaller this component, the more effective is the rectifier.
“The ratio of rms value of a.c. component to the d.c. component in the rectifier output
is known as ripple factor”
I ac
r=
I dc
2.6.1 Ripple factor for Half-wave rectification
By definition the effective (i.e. rms) value of total load current is given by
I rms = ( I ac2 + I dc2 )
OR I ac = ( I rms
2
− I dc2 )
where Idc = value of d.c. component
Iac = rms value of a.c. component
Divide both R.H.S and L.H.S. by Idc we get
I ac 1
= 2
( I rms − I dc2 )
I dc I dc
2
 I rms 
r=   − 1 (1)
 I dc 
Im
for half-wave rectification, we have I rms =
2
Im
I dc =
π
Substituting above values in equation (1) we get,

ripple factor r = 1.21
It is clear that a.c. component exceeds d.c. component in the output of a half-wave
rectifier.
2.6.2 Ripple factor for full-wave rectification
Im
For full wave rectification we have Irms =
2
2I m
Idc =
π
Substituting above values in equation (1) we get,
ripple factor r = 0.48
This shows that in the output of Full-wave rectifier, the d.c. component is more than the
a.c. component
2.7 Comparision of Rectifiers
Particulars Half wave rectifier Centre-tapped Full Bridge rectifier

wave rectifier
1. No. of diodes 1 2 4
2. Idc Im / Π 2Im /Π 2Im /Π
3. Vdc Vm / Π 2Vm / Π 2Vm / Π
4. Irms Im / 2 Im /√ 2 Im /√ 2
5. Efficiency 40.6 % 81.2 % 81.2 %
6. PIV Vm 2Vm Vm
7. Ripple factor 1.21 0.48 0.48
Note:
• The relation between turns ratio and voltages of primary and secondary of the
transformer is given by

o N1 / N2 = Vp / Vs
• RMS value of voltage and Max. value of voltage is related by the equation.
Vrms = Vm / √2 ( for full-cycle of a.c.)
• If the type of diode is not specified then assume the diode to be of silicon type.
• For an ideal diode, forward resistance rf = 0 and cut-in voltage, Vγ = 0.
2.8 FILTERS
We know that the output of the rectifier is pulsating d.c. i.e. the output obtained by the
rectifier is not pure d.c. but it contains some a.c. components along with the d.c. o/p.
These a.c. components are called as Ripples, which are undesirable or unwanted. To
minimize the ripples in the rectifier output filter circuits are used. These circuits are
normally connected between the rectifier and load as shown below.
Vi
Vo pure d.c. o/p
Rectifier Filter
Pulsating d.c. output
A filter is a circuit which converts pulsating d.c. output from a rectifier to a steady d.c.
output. In other words, filters are used to reduce the amplitudes of the unwanted a.c.
components in the rectifier.
Note: A capacitor passes a.c. signal readily but blocks d.c..

2.8.1 Types of Filters
1. Capacitor Filter (C-Filter)
2. Inductor Filter
3. Choke Input Filter (LC-filter)
4. Capacitor Input Filter (Π-filter)
2.8.2 Capacitor Filter (C-filter)
(i)
Vin
a f
e
t
b d
V1
o/p without
filter
VO
o/p
with filter a
e
Fig.2.8 Capacitor filter (C-filter) (i) Circuit diagram (ii) waveforms

• When the input signal rises from 0 to a the diode is forward biased therefore it
starts conducting since the capacitor acts as a short circuit for a.c. signal it gets
charged up to the peak of the input signal and the d.c. component flows through
the load RL.
• When the input signal fall from a to b the diode gets reverse biased. This is
mainly because of the voltage across the capacitor obtained during the period o to
a is more when compared to Vi. Therefore there is no conduction of current
through the diode.
• Now the charged capacitor acts as a battery and it starts discharging through the
load RL. Mean while the input signal passes through b,c,d section. When the
signal reaches the point d the diode is still reverse biased since the capacitor
voltage is more than the input voltage.
• When the signal reaches point e, the input voltage can be expected to be more
than the capacitor voltage. When the input signal moves from e to f the capacitor
gets charged to its peak value again. The diode gets reverse biased and the
capacitor starts discharging. The final output across RL is shown in Fig. 2.8
The ripple factor for a Half-wave rectifier with C-filer is given by
r= ½√3fCRL
f the line frequency ( Hz)

C capacitance (F)
RL Load resistance (Ω)
Ripple factor for full-wave rectifier with C-filter is given by r = 1/4 √3 f C RL
2.8.3 Advantages of C-Filter
• low cost, small size and good characteristics.

• It is preferred for small load currents (up to 50 mA)
• It is commonly used in transistor radio, batteries eliminator etc.

2.9 Zener Diode
The reverse voltage characteristic of a semiconductor diode including the breakdown

region is shown below.
V Vz 0
Fig. 2.9 Zener diode characteristics
Zener diodes are the diodes which are designed to operate in the breakdown region. They
are also called as Breakdown or Avalanche diodes.
The symbol of Zener diode is shown below
P N
Fig. 2.10 Symbol of Zener diode
The breakdown in the Zener diode at the voltage Vz may be due to any of the
following mechanisms.
1. Avalanche breakdown
Depletion region charge carriers striking the atoms
( ) ( )
P N
-ve terminal +ve terminal
minority charge carriers
Fig. 2.11 Avalanche breakdown in Zener diode

• We know that when the diode is reverse biased a small reverse saturation current
I0 flows across the junction because of the minority carriers in the depletion
region.

• The velocity of the minority charge carriers is directly proportional to the applied
voltage. Hence when the reverse bias voltage is increased, the velocity of minority
charge carriers will also increase and consequently their energy content will also
increase.
• When these high energy charge carriers strikes the atom within the depletion
region they cause other charge carriers to break away from their atoms and join
the flow of current across the junction as shown above. The additional charge
carriers generated in this way strikes other atoms and generate new carriers by
making them to break away from their atoms.
• This cumulative process is referred to as avalanche multiplication which results in

the flow of large reverse current and this breakdown of the diode is called
avalanche breakdown.
2. Zener breakdown
We have; electric field strength = Reverse voltage/ Depletion region
Depletion region
( ) ( )
P N
-ve terminal +ve terminal
electrons pulled out of their covalent

bonds because of high intensity electric field
Fig.2.12 Zener breakdown in Zener diode
From the above relation we see that the reverse voltage is directly proportional to the
electric field hence, a small increase in reverse voltage produces a very high intensity
electric field within a narrow depletion region.
Therefore when the reverse voltage to a diode is increased, under the influence of high
intensity electric filed large number of electrons within the depletion region break the
covalent bonds with their atoms as shown above and thus a large reverse current flows
through the diode. This breakdown is referred to as Zener breakdown.

2.9.1 Zener voltage regulator
The circuit diagram of Zener voltage regulator is shown below

Rs
I IZ IL
Vin VZ RL Vo
Fig. 2.13 Zener voltage regulator
A Zener diode of breakdown voltage VZ is connected in reverse biased condition across

the load RL such that it operates in breakdown region. Any fluctuations in the current are
absorbed by the series resistance Rs. The Zener will maintain a constant voltage VZ
(equal to Vo) across the load unless the input voltage does not fall below the Zener
breakdown voltage VZ.
Case(i) When input voltage Vin varies and RL is constant
Rs
I IZ IL
Vin VZ RL Vo
If the input voltage increases, the Zener diode which is in the breakdown region is
equivalent to a battery VZ as shown in figure. The output voltage remains constant at VZ
(equal to Vo) and the excess voltage is dropped across the series resistance RS. We know
that for a Zener diode under breakdown region large change in current produces very
small change in voltage, thereby the output voltage remains constant.
Case (ii) When Vin is constant and RL varies.

Rs
I IZ IL
Vin VZ RL Vo

If there is a decrease in the load resistance RL and the input voltage remains constant then
there is an increase in load current.
Since Vin is constant the current cannot come from the source. This addition load current
is driven from the battery VZ and we know that even for a large decrease in current the
Zener output voltage Vz remains same. Hence the output voltage across the load is also
constant.
2.9.2 Other Special Purpose Diodes
Schottky diodes
Tunnel diodes
Light-emitting diodes
Laser diodes Light Emitting Diode
Photodiodes
Solar cells
Varicap or varactor diodes
Snap diode
PIN diodes Photodiode
IMPATT diode
Gunn diode
Shockley diode
Constant-current diodes
Schottky diode
Varicap Diode

CHAPTER 3
BIPOLAR JUNCTION TRANSISTORS
A transistor is a sandwich of one type of semiconductor (p-type or n-type) between two

layers of other types.
Transistors are classified into two types;

1. p-n-p transistor
p-n-p transistor is obtained when a n-type layer of silicon is sandwiched
between two p-type silicon material.
2. n-p-n transisitor
n-p-n transistor is obtained when a p-type layer of silicon is sandwiched
between two n-type silicon materials.
Figure 3.1 below shows the schematic representations of a transistor which is almost
equivalent of two diodes connected back to back.
JE JC JE JC
E C E C
p n p n p n
B B
Fig 3.1: Schematic representation
p-n-p n-p-n
Fig 3.2: Symbolic representation
¾ The three portions of transistors are named as emitter, base and collector. The
junction between emitter and base is called emitter-base junction while the junction
between the collector and base is called collector-base junction.
¾ The base is thin and lightly doped, the emitter is heavily doped and it is wider when
compared to base, the width of the collector is more when compared to both base and
emitter.

¾ In order to distinguish the emitter and collector an arrow is included in the emitter.
The direction of the arrow depends on the conventional flow of current when emitter
base junction is forward biased.
¾ In a p-n-p transistor when the emitter junction is forward biased the flow of current is
from emitter to base hence, the arrow in the emitter of p-n-p points towards the base.
3.1 Operating regions of a transistor
A transistor can be operated in four different modes or regions as

a) active region
b) saturation region
c) cut-off region
d) inverse mode (rarely used)
Active region
E JE B JC C
p n p
VEE VCC
Fig 3.3: p-n-p transistor operated in active region
The transistor is said to be operated in active region when the emitter-base junction is
forward biased and collector –base junction is reverse biased. The collector current is said
to have two current components one is due to the forward biasing of EB junction and the
other is due to reverse biasing of CB junction. The collector current component due to the
reverse biasing of the collector junction is called reverse saturation current (ICO or ICBO
Collector to Base current when emitter is Open) and it is usually very small in magnitude
(2-5 µA for Ge and 0.1 – 1 µA for Si).
Saturation region
E JE B JC C
p n p
VEE VCC
Fig 3.4: p-n-p transistor operated in saturation region

Transistor is said to be operated in saturation region when both EB junction and CB
junction are forward biased as shown. When transistor is operated in saturation region IC
increases rapidly for a very small change in VC.
Cut-off region
E JE B JC C
p n p
VEE VCC
Fig 3.5: p-n-p transistor operated in Cut-off region
When both EB junction and CB junction are reverse biased, the transistor is said to be
operated in cut-off region. In this region, the current in the transistor is very small and
thus when a transistor in this region it is assumed to be in off state.
3.2 Working of a transistor (p-n-p)
E JE B JC C
IE IE IC IC
p n p
ICO
IB
VEB VCB
Fig 3.6 Transistor in active region
• Consider a p-n-p transistor operated in active region as shown in Figure 3.6
• Since the EB junction is forward biased large number of holes present in the
emitter as majority carriers are repelled by the +ve potential of the supply
voltage VEE and they move towards the base region causing emitter current IE.
• Since the base is thin and lightly doped very few of the holes coming from the
emitter recombine with the electrons creating base current IB. All the

remaining holes move towards the collector. Since the CB junction is reverse
biased all the holes are immediately attracted by the –ve potential of the
supply VCB. Thereby giving rise to collector current IC.
• Thus we see that IE = IB + IC -----------------(1) (By KCL)
• Since the CB junction is reverse biased a small minority carrier current ICO
flows from base to collector.
3.3 Current components of a transistor
JE JC
IPE IPC
(hole current) IPB (hole current)
IE INE (e- current) ICO
IC
IB
VEE VCC
Fig 3.7: Current components of a transistor
Fig 3.7 above shows a transistor operated in active region. It can be noted from the
diagram the battery VEE forward biases the EB junction while the battery VCC reverse
biases the CB junction.
As the EB junction is forward biased the holes from emitter region flow towards the base
causing a hole current IPE. At the same time, the electrons from base region flow towards
the emitter causing an electron current INE. Sum of these two currents constitute an
emitter current IE = IPE +INE.
The ratio of hole current IPE to electron current INE is directly proportional to the ratio of
the conductivity of the p-type material to that of n-type material. Since, emitter is highly
doped when compared to base; the emitter current consists almost entirely of holes.
Not all the holes, crossing EB junction reach the CB junction because some of them
combine with the electrons in the n-type base. If IPC is the hole current at (Jc) CB
junction. There will be a recombination current IPE - IPC leaving the base as shown in
figure 3.7.

If emitter is open circuited, no charge carriers are injected from emitter into the base and
hence emitter current IE = 0. Under this condition CB junction acts a reverse biased diode
and therefore the collector current (IC = ICO) will be equal to the reverse saturation
current. Therefore when EB junction is forward biased and collector base junction is
reverse biased the total collector current IC = IPC +ICO.
3.4 Transistor configurations

We know that, a transistor can be used as an amplifier. For an amplifier, two terminals
are required to supply the weak signal and two terminals to collect the amplified signal.
Thus four terminals are required but a transistor is said to have only three terminals
Therefore, one terminal is used common for both input and output.
This gives rise to three different combinations.

1. Common base configuration (CB)
2. Common emitter configuration (CE)
3. Common collector configuration (CC)
3.4.1. CB configuration
A simple circuit arrangement of CB configuration for p-n-p transistor is shown below.
IE IC
Vi IB RL Vout
VEB VCB
Fig 3.8: CB configuration
In this configuration, base is used as common to both input and output. It can be noted
that the i/p section has an a.c. source Vi along with the d.c. source VEB. The purpose of
including VEE is to keep EB junction always forward biased (because if there is no VEE
then the EB junction is forward biased only during the +ve half-cycle of the i/p and
reverse biased during the –ve half cycle). In CB configuration, IE is i/p current and IC is
o/p current.
Current relations
1. Current amplification factor (αdc)
It is defined as the ratio of d.c. collector current to d.c. emitter current
IC
αdc =
IE

2. Total o/p current
We know that CB junction is reverse biased and because of minority charge carriers a
small reverse saturation current ICO flows from base to collector.
IC = IC(INJ) + ICO
Since a portion of emitter current IE flows through the base, let remaining emitter current
(injected into collector) be αdc IE.
IC = αdc IE + ICo
Characteristics
1. Input characteristics
IE
VCB=10V VCB=5V
VEB
Fig 3.9: Input characteristics
I/p characteristics is a curve between IE and emitter base voltage VEB keeping VCB
constant. IE is taken along y-axis and VEB is taken along x-axis. From the graph following
points can be noted.
1. For small changes of VEB there will be a large change in IE. Therefore input
resistance is very small.
2. IE is almost independent of VCB
3. I/P resistance , Ri = ∆VEB / ∆ IE VCB =constant
2. Output characteristics
IC
Active region
IE=3 mA
IE =2 mA
Saturation IE = 1 mA
region IE = 0
Cut-off region VCB

Fig 3.10: Output characteristics

o/p characteristics is the curve between IC and VCB at constant IE. The collector current IC
is taken along y-axis and VCB is taken along x-axis. It is clear from the graph that the o/p
current IC remains almost constant even when the voltage VCB is increased.
i.e. a very large change in VCB produces a small change in IC. Therefore, output resistance
is very high.
o/p resistance Ro = ∆VEB / ∆ IC IE = constant
Region below the curve IE =0 is known as cut-off region where IC is nearly zero. The
region to the left of VCB =0 is known as saturation region and to the right of VCB =0 is
known as active region.
2. CE configuration
IC
RL Vout
IB
Vi IE
VEB VCE
Fig 3.11: CE configuration
In this configuration the input is connected between the base and emitter while the output
is taken between collector and emitter. For this configuration IB is input current and IC is
the output current.
1. Current amplification factor (βdc)
It is the ratio of d.c. collector current to d.c. base current.

i.e., βdc = IC / IB
2. Relationship between αdc and βdc
IC
We know that αdc =
IE
IC
αdc =
IB + IC
divide both numerator and denominator of RHS by IC, we get

1
α dc =
IB
+1
IC
1
α dc = ( IC / IB = βdc )
1
+1
β dc
β dc
α dc =
1 + β dc
Also we have
α (1 + β ) = β
α + αβ = β
α = β − αβ
α = β (1 − α )
α
β=
1−α
Derivation of Total Output Current IC
We have I C = αI E + I CBO
β
IC = I E + I CBO
1 + B
βI + ( 1 + β ) I CBO
IC = E
1 + β
Ic = β I B + (1 + β ) I CBO

Transistor Characteristics
1. i/p characteristics
IB
VCE=10V VCE=5V
VEB
Fig 3.11: i/p characteristics
Input characteristics is a curve between EB voltage (VEB ) and base current (IB ) at
constant VCE. From the graph following can be noted.
1. The input characteristic resembles the forward characteristics of a p-n junction

diode.
2. For small changes of VEB there will be a large change in base current IB. i.e., input
resistance is very small.
3. The base current is almost independent of VCE.
4. Input resistance , Ri = ∆VEB / ∆ IB V CE = constant
2. Output characteristics
IC
(mA)
Active region
30 µA
20 µA
10 µA
IB =0µA
Cut-off region
V CE(volts)
Fig 3.12: Output characteristics
It is the curve between VCE and IC at constant IB. From the graph we can see that,
1. Very large changes of VCE produces a small change in IC i.e. output resistance is
very high.
2. output resistance Ro = ∆VCE / ∆IC │IB = constant
Region between the curve IB =0 is called cut-off region where IB is nearly zero. Similarly
the active region and saturation region is shown on the graph.

3. CC configuration
IE
RL Vout
IB
Vi IC
VCB VCE
Fig 3.13: CC configuration
In this configuration the input is connected between the base and collector while the
output is taken between emitter and collector.
Here IB is the input current and IE is the output current.
Current relations
1. Current amplification factor (γ)
2. Relationship between α β and γ
IE
γ=
IB
I B + IC
γ=
IB
divide both Numerator and denominator by IB
IC
1+
IB
γ=
1
γ = 1+ β ( β = IC / IB)

α
γ = 1+
1−α
1
γ = -------------------------------------
1−α
Derivation of total output current IE
We know that IC = αI E + I CBO
IE = IB + IC
IE = IB + αIE + ICBO
IE(1-α ) = IB + ICBO
IB I
IE = + CBO
1−α 1−α
IE = γIB + γICBO
IE = γ (IB + ICBO) -----------------------------

3.5 Comparison between CB, CC and CE configuration
Characteristics CB CE CC
1. Input resistance (Ri) low low high
2. Output resistance (Ro) high high low
3. Current amplification β α 1
factor α= β= γ =
1+ β 1−α 1−α
4. Total output current Ic = β I B + (1 + β ) I CBO IE = γIB + γICBO
I C = αI E + I CBO
5. Phase relationship
between input and output In-phase in-phase
Out-of phase
For high frequency For audio frequency For impedance

6. Applications applications matching
applications
Less than unity Greater than unity Very high

7. Current gain
Very high Grater than unity Less than unity
8. Voltage gain

3.6 Transistor as an amplifier
IC
RL Vout
IB
Vi ` IE
VBB VCC
Fig 3.13: Transistor as an amplifier
Consider a n-p-n transistor in CE configuration as shown above along with its input
characteristics.
A transistor raises the strength of a weak input signal and thus acts as an amplifier. The
weak signal to be amplified is applied between emitter and base and the output is taken
across the load resistor RC connected in the collector circuit.
In order to use a transistor as an amplifier it should be operated in active region i.e.

emitter junction should be always FB and collector junction should be RB. Therefore in
addition to the a.c. input source Vi two d.c. voltages VBB and VCC are applied as shown.
This d.c. voltage is called bias voltage.
As the input circuit has low resistance, a small change in the signal voltage Vi causes a
large change in the base current thereby causing the same change in collector current
(because IC = βIB).
The collector current flowing through a high load resistance RC produces a large voltage
across it. Thus a weak signal applied at the input circuit appears in the amplified form at
the output. In this way transistor acts as an amplifier.
Example: Let RC = 5KΩ, Vin =1V, IC =1mA then output Vout=ICRC =5V

3.7 Bias stabilization
The process of making operating point independent of temperature changes or variation

in transistor parameters is called the stabilization.
We know that for transistor to operate it should be properly biased so that we can have a
fixed operating point. To avoid any distortions, the Q-point should be at the centre of the
load line.
But in practice this Q-point may shift to any operating region (saturation or cur-off
region) making the transistor unstable. Therefore in order to avoid this, biasing stability
should be maintained.
3.8 Causes for Bias instability
Bias instability occurs mainly due to two reasons.

1. Temperature
2. Current gain
1. Temperature (T)
The temperature at the junctions of a transistor depends on the amount of current flowing
through it. Due to increase in temperature following parameters of a transistor will
change.
(a) base-emitter voltage (VBE)
VBE increases at a rate of 2.4mV/0C. With increase in temperature the base current IB will
increase and since IC= βIB, IC is also increased hence, changing the Q-point.
(b) Reverse saturation current ( ICBO)
We know that IC = βIB + (1+β) ICBO where ICBO is the reverse saturation current. As the
temperature increases ICBO increases there by increase in IC and hence changing the Q-
point.
2. Current gain (β)
In the process of manufacturing the transistors different transistors of same type may
have different parameters (i.e. if we take two transistor units of same type and use them
in the circuit there is a change in the β value in actual practice). The biasing circuit will
be designed according to the required β value but due to the change in β from unit to unit
the operating point may shift.

3.9 Cascading transistor amplifiers
When the amplification provided by a single stage amplifier is not sufficient for a
particular purpose or when the input and output impedance is not of the correct
magnitude for the required application then two or more amplifiers are connected in
cascade as shown below.
Fig 3.14: Cascading transistor amplifiers
Here the output of amplifier 1 is connected as the input of amplifier 2.
Example: The gain of a single amplifier is not sufficient to amplify a signal from a weak
source such as microphone to a level which is suitable for the operation of another circuit
as loud speaker. In such cases, amplifiers are used.
When amplifiers are cascaded, individual amplifiers provides required amplification and
input and output provide impedance matching.
Decibel (dB)
Many a times it is convenient to represent the gain of an amplifier on a log scale instead
of a linear scale. The unit of this log scale is called decibel.
Power gain =loge( Pout /Pin ) bel
Power gain in dB =10 log10( Pout /Pin ) dB
Voltage gain =20log10( Vout /Vin ) dB
Current gain = 20log10(Iout / Iin ) dB
Note: For a multistage amplifier if AV1, AV2, and AV3 are the voltage gains of amplifier
1,2, and 3 respectively then the overall voltage gain AV = AV1 x AV2 x AV3.
If it is expressed in dB the AV(dB) = AV1(dB) + AV2(dB) +AV3(dB)
Similarly for four or more stages.

3.10 Single stage RC coupled Amplifier
VCC
Vo
R1 RC CC
Vo t
Cin
RS
R2 RE CE RL
Vi
Fig 3.15: single stage RC-coupled amplifier
Figure above shows a practical circuit of a single stage RC coupled amplifier. The
different circuit components and their functions are as described below.
a. Input capacitor(Cin)- This capacitor is used to couple the input signal to the base
of the transistor if it is not used, the signal source resistance RS gets in parallel
with R2 thus changing the bias. The capacitor Cin blocks any d.c. component
present in the signal and passes only a.c. signal for amplification.
b. Biasing circuit –The resistances R1, R2 and RE forms the biasing and stabilization
circuit for the CE amplifier. It sets the proper operating point for the amplifier.
c. Emitter bypass capacitor (CE)-This capacitor is connected in parallel with the

emitter resistance RE to provide low reactance path to the amplified a.c. signal. If
it is not used, the amplified a.c. signal passing through RE will cause voltage drop
across it thereby reducing the output voltage of the amplifier.
d. Coupling capacitor (CC) - This capacitor couples the output of the amplifier to
the load or to the next stage of the amplifier. If it is not used, the biasing
conditions of the next stage will change due to the parallel effect of collector
resistor RC.
i.e. RC will come in parallel with the resistance R1 of the biasing network of the
next stage thus changing the biasing conditions of the next stage amplifier.

3.11 Two stage RC coupled amplifier
VCC
R1 RC CC R11 RC1
CC1
RS
R2 RE CE R21 CE 1 RL
Vi RE1
Stage-1 Stage-2
Fig 3.16: Two stage RC coupled Amplifier
Figure above shows the circuit diagram of a two stage RC coupled amplifier. The
coupling capacitor CC connects the output of the first stage to the input of the second
stage. Since the coupling from one stage to the next stage is achieved by coupling
capacitor along with a shunt resistor the amplifier is called RC coupled amplifier. The
input signal is first applied to the transistor T1 and output is taken at the collector of T1.
The signal at the output will be 1800 out of phase when compared to the input. The output
is taken across RC with the help of a coupling capacitor. This signal is fed as input to the
next stage i.e. transistor T2. The signal is amplified further and the amplified output is
taken across Rc1 of T2. The phase of the signal is reversed again. The output is amplified
twice and it is amplified replica of the input signal.
3.12 Frequency response in amplifier

Frequency response is the curve between the gain of the amplifier (A = Vo / Vi)
verses the frequency of the input signal. The frequency response of a typical RC-
coupled amplifier is shown below.
Frequency response has 3 regions.
1. Low frequency range

2. Mid frequency range
3. High frequency range

Gain in
dB LFR MFR HFR
f1 f2 freq(Hz)
Fig 3.16: Frequency response in amplifier
Low frequency range (< 50 Hz)
We have
1
Xc = where XC ----- reactance of capacitor;
2πRC
f-----frequency
Since frequency is inversely proportional to the reactance, the reactance of the coupling
capacitor CC will be quite high at low frequencies.
Hence very small amount of signal will pass through one stage to the next stage.
Moreover CE cannot shunt the emitter resistance RE effectively because of its large
reactance at low frequency. These two factors causes the fall of voltage gain at low
frequencies.
Mid frequency range (50Hz - 20 KHz)

In this range of frequencies, voltage gain of the amplifier is constant. The effect of
coupling capacitor in this range is as such to maintain a uniform voltage gain.
High frequency range (> 20 KHz)

In this range of frequency, the reactance of the coupling capacitor CC is very small and it
behaves as a short circuit. This increases the loading effect of next stage (RC will comes
in parallel with R1) and reduces the voltage gain. This reduces the current amplification
there by the voltage drops at high frequencies.
Advantages of RC coupled amplifer

1. Low cost-Because only resistors and capacitors are used for biasing and coupling
which are cheap.
2. Compact-Because modern resistor and capacitors are small and light
3. Good frequency response- The gain is constant over the audio frequency range
and hence suitable for audio frequency amplification.

3.13 DC Load Line and Operating point selection
IC
RB RC
VCE
IB
VBB VCC
Fig 3.17:n-p-n transistor in CE configuration
IC
(mA) Q-point
A
30 µA
20 µA
10 µA
IB =0µA
B V CE(volts
Fig.3.18: output characteristics
Consisder a CE amplifier along with the output characteristics as shown in figure 3.18
above. A straight line drawn on the output characteristic of a transistor which gives the
various zero signal values (i.e. when no signal applied) of VCE and IC is called DC load
line.
Construction of DC load line

Applying KVL to the collector circuit we get,
VCC –ICRC –VCE =0-------------------1
VCE = VCC –ICRC ----------------------2
The above equation is the first degree equation and can be represented by a
straight line. This straight line is DC load line.

To draw the load line we require two end points which can be found as follows.
1. If IC =0, eqn 2 becomes VCE = VCC

2. If VCE = 0, eqn 2 becomes VCC = ICRC i.e. IC = VCC /RC
3.14 Operating point (Q)
A point on the d.c. load line which represent the zero signal values of VCE and IC in a
transistor is called as operating point or silent point or quiescent point or Q-point.
The Q-point is selected where the DC load line intersects the curve of output
characteristics for particular value of zero signal current.
i.e. Q-point = (VCE ,IC)

CHAPTER 4
FIELD EFFECT TRANSISTORS
FET’s (Field – Effect Transistors), developed in the 1960s, are much like BJT’s (Bipolar
Junction Transistors).
Similarities:
• Amplifiers
• Switching devices
• Impedance matching circuits
Differences:
• FET’s are voltage controlled (field effect) devices whereas BJT’s are current
controlled devices.
• FET’s also have a higher input impedance, but BJT’s have higher gains.
• FET’s are less sensitive to temperature variations and because of their
construction they are more easily integrated on IC’s.
• FET’s are also generally more static sensitive than BJT’s.
• FET’s are unipolar devices
FET Types
• JFET ~ Junction Field-Effect Transistor
• MOSFET ~ Metal-Oxide Field-Effect Transistor – aka Insulated Gate FET (IGFET)
- D-MOSFET ~ Depletion MOSFET
- E-MOSFET ~ Enhancement MOSFET
JFET Construction
There are two types of JFET’s: n-channel and p-channel.
The n-channel is more widely used.
There are three terminals: Drain (D) and Source (S) are connected to n-channel Gate (G)
is connected to the p-type material

JFET Operating Characteristics
There are three basic operating conditions for a JFET:
(i) VGS = 0, VDS increasing to some positive value
(ii) VGS < 0, VDS at some positive value
(iii) Voltage-Controlled Resistor
------------------------------------------------------------------------------------------------------------
(i). VGS = 0, VDS increasing to some positive value
Three things happen when VGS = 0 and VDS is increased from 0 to a more positive
voltage:
• the depletion region between p-gate and n-channel increases as electrons from n-
channel combine with holes from p-gate.
• increasing the depletion region, decreases the size of the n-channel which
increases the resistance of the n-channel.
• But even though the n-channel resistance is increasing, the current (ID) from
Source to Drain through the n-channel is increasing. This is because VDS is
increasing.
Pinch-off
If VGS = 0 and VDS is further increased to a more positive voltage, then the depletion zone
gets so large that it pinches off the n-channel. This suggests that the current in the n-
channel (ID) would drop to 0A, but it does just the opposite: as VDS increases, so does ID.

At the pinch-off point:
• any further increase in VGS does not produce any increase in ID. VGS at pinch-off is
denoted as Vp.
• ID is at saturation or maximum. It is referred to as IDSS.
• The ohmic value of the channel is at maximum.
(ii). VGS < 0, VDS at some positive value
As VGS becomes more negative the depletion region increases.

ID < IDSS
The region to the left of the pinch-off point is called the ohmic region. The JFET can be used as a
variable resistor, where VGS controls the drain-source resistance (rd). As VGS becomes more
negative, the resistance (rd) increases.
p-Channel JFETS
p-Channel JFET acts the same as the n-channel JFET, except the polarities and currents are
reversed.

P-Channel JFET Characteristics
As VGS increases more positively:

• the depletion zone increases
• ID decreases (ID < IDSS)
• eventually ID = 0A
Also note that at high levels of VDS the JFET reaches a breakdown situation. ID increases
uncontrollably if VDS > VDSmax.
JFET Symbols
n-channel
Arrow points from p-side to n-side
Capacitance of GD side is normally less than GS side, hence D & S cannot be interchanged at high frequencies.
Transfer Characteristics
The transfer characteristic of input-to-output is not as straight forward in a JFET as it was in a BJT.
In a BJT, β indicated the relationship between IB (input) and IC (output). In a JFET, the relationship
of VGS (input) and ID (output) is a little more complicated:

Transfer (Transconductance) Curve
From this graph it is easy to determine the value of ID for a given value of VGS.
Plotting the Transfer (Transconductance) Curve

Using IDSS and Vp (VGS(off)) values found in a specification sheet, the Transfer Curve can be plotted
using these 3 steps:
Because of the form of the transconductance relationship, FETs are called square law devices

MOSFETs
MOSFETs have characteristics similar to JFETs and additional characteristics that make them very
useful. There are 2 types:
• Depletion-Type MOSFET
• Enhancement-Type MOSFET
Depletion-Type MOSFET Construction

The Drain (D) and Source (S) connect to the n-doped regions. These N-doped regions are connected via an n-
channel. This n-channel is connected to the Gate (G) via a thin insulating layer of SiO2. The n-doped material
lies on a p-doped substrate that may have an additional terminal connection called SS.
Depletion-type MOSFET in Depletion Mode
The characteristics are similar to the

JFET.
When VGS = 0V, ID = IDSS
When VGS < 0V, ID < IDSS
The formula used to plot the Transfer
Curve still applies:
Depletion mode
Depletion-type MOSFET in Enhancement Mode
Enhancement mode
VGS > 0V, ID increases above IDSS. The formula used to plot the Transfer Curve still applies:
(note that VGS is now a positive polarity)

p-Channel Depletion-Type MOSFET
The p-channel Depletion-type MOSFET is similar

to the n-channel except that the voltage polarities
and current directions are reversed.
Enhancement-Type MOSFET Construction
The Drain (D) and Source (S) connect to the n-doped regions.
These n-doped regions are connected via an n-channel. The Gate
(G) connects to the p-doped substrate via a thin insulating layer
of SiO2. There is no channel. The n-doped material lies on a p-
doped substrate that may have an additional terminal connection
called SS.
Basic Operation
The Enhancement-type MOSFET only operates in the enhancement mode.

VGS is always positive as VGS
increases, ID increases But if VGS
is kept constant and VDS is
increased, then ID saturates (IDSS)
The saturation level, VDSsat is
reached.
Transfer Curve
To determine ID given VGS:
where VT = threshold voltage or voltage at which the MOSFET turns on.

k = constant found in the specification sheet
k can also be determined by using values at a specific point and the formula:
VDSsat can also be calculated:
p-Channel Enhancement-Type MOSFETs
The p-channel Enhancement-type MOSFET is similar to the n-channel except that the voltage polarities and
current directions are reversed.

Comparison of FET with BJT
1) JFET has high input resistance in the order of 10 MΩ, MOSFETs in order of 1012Ω,
as compared to BJT in the order of 1kΩ.
2) The operation of FETs depend on majority carriers only (unipolar) hence relatively
less noisy.
3) FETs are voltage controlled, BJTs are current controlled. Most signals to be
processed are voltage signals. Means FETS are more suitable.
4) Power gain of an FET is much higher than for a BJT, therefore often no need of
driver stage.
5) FETs consume less power.
6) FETs have negative temperature coefficient of drain current, hence no risk of thermal
runaway.
7) MOSFETS are simpler and less expensive to fabricate than BJTs
8) MOS circuits require less area on a silicon chip. Allows for greater integration.

Basic Electronics4 - 1-1-1-1-1

Uploaded by

Copyright:

Available Formats

Basic Electronics4 - 1-1-1-1-1

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Basic Electronics4 - 1-1-1-1-1

Uploaded by

Copyright:

Available Formats

SCHOOL OF ENGINEERING

DEPARTMENT OF ELECTRICAL & COMMUNICATIONS

ECE 281 BASIC ELECTRONICS (3 units)

Introduction to semi-conductors and diodes:

Course Lecturer: Dr. E. Ataro (Academic year 2011/2012)

ECE 281 BASIC ELECTRONICS (2011/2012) 1

Electrons and holes in an intrinsic semiconductors, conductivity of a semiconductor,

Electronics essentially deals with electronic devices and their utilization.

• An Electrostatic force of attraction between electrons and the nucleus holds up

Figure1.1. Atomic structure

ECE 281 BASIC ELECTRONICS (2011/2012) 2

• atomic weight = no. of protons + no. of neutrons

• An electron is a negatively charged particle having negligible mass. The charge

• atomic number = no. of protons or electrons in an atom

For example, orbit I contains 2x12 =2 electrons

orbit II contains 2x22 = 8 electrons

orbit III contains 2x32 = 18 electrons and so on

• The last orbit cannot have more than 8 electrons.

Positive and negative ions

• If an atom gains an electron it becomes negatively charged and is referred to as

• The outermost orbit can have a maximum of 8 electrons.

• The valence electrons determine the physical and chemical properties of a

ECE 281 BASIC ELECTRONICS (2011/2012) 3

• In certain substances, particularly metals, the valence electrons possess so much

ECE 281 BASIC ELECTRONICS (2011/2012) 4

Figure1.2 Energy level diagram

• The range of energies possessed by valence electrons is called valence band.

• The range of energies possessed by free electrons is called conduction band.

Classification of materials based on Energy band theory

Valence Valence Valence

(a) Conductor (b) Insulator (c) Semiconductor

ECE 281 BASIC ELECTRONICS (2011/2012) 5

• In terms of energy bands, conductors are those substances in which there is no

• Semiconductors are those substances whose conductivity lies in between that of a

• In terms of energy bands, semiconductors are those substances in which the

• Therefore, comparatively smaller electric field is required to push the electrons

ECE 281 BASIC ELECTRONICS (2011/2012) 6

• Conduction in any given material occurs when a voltage of suitable magnitude is

• This may be due to electron motion or hole transfer or both.

• Hole transfer involves the movement of holes.

(a) Conductor (b) Semiconductor

Flow of electrons Flow of electrons

Flow of current (conventional) Flow of holes

ECE 281 BASIC ELECTRONICS (2011/2012) 7

Semiconductors are classified into two types.

• A semiconductor in an extremely pure form is known as intrinsic

Example: Silicon, germanium.

• Both silicon and Germanium are tetravalent (having 4 valence electrons).

Figure1.3. Crystalline structure of Silicon (or Germanium)

• The semiconductor therefore behaves as an insulator at absolute zero

ECE 281 BASIC ELECTRONICS (2011/2012) 8

Figure 1.4. Crystalline structure of Silicon (or Germanium) at room temperature

• When an impurity is added to an intrinsic semiconductor its conductivity changes.

• This process of adding impurity to a semiconductor is called doping and the

• Depending on the type of impurity added, extrinsic semiconductors are further

ECE 281 BASIC ELECTRONICS (2011/2012) 9

Figure 1.5 n-type semiconductor

Forbidden gap Fermi level

Figure1.6 Energy band diagram for n-type semiconductor