Kassen RS-720 EN

2D Desktop Barcode Scanner
User Manual
Contents
1st Chapter:Introduction......................................................................... 1
2nd Chapter: Product Features............................................................... 1
3rd Chapter :Parameters......................................................................... 2
Electrical Parameters............................................................................................ 2
Physical Parameter.............................................................................................. 2
Environment.......................................................................................................... 2
Decode Ability........................................................................................................ 2
Depth of Scan......................................................................................................... 2
Appearance............................................................................................................ 3
Factory Default Setting..........................................................................................4
4nd Chapter: Interfaces........................................................................... 4
Introduction........................................................................................................... 4
RS232...................................................................................................................... 4
RS232 Baud Rate....................................................................................................4
RS232 ：Data Bits,Stop Bits,Parity......................................................................5
USB..........................................................................................................................6
USB HID .................................................................................................................6
USB COM................................................................................................................6
5rd Chapter:Input/Output Settings........................................................ 6
Introduction.......................................................................................................... 6
Buzzer Setting when Electrifyin........................................................................... 6
Buzzer Setting when Decode successfully.......................................................... 7
Buzzer ON or OFF Setting................................................................................ 7
Volume Settings............................................................................................... 7
Frequency Settings.......................................................................................... 7
Beep Status Setting after Decoding Successfully......................................... 7
Output Delayed................................................................................................ 8
Lighting Setting.................................................................................................... 8
Standby Setting................................................................................................... 8
6th Chapter:Data Editing..........................................................................9
Prefix/Suffix Settings............................................................................................. 9
Ending Character Settings.................................................................................. 10
Keyboard Operation............................................................................................ 10
Function Code Transmission Setting................................................................. 10
Data Transmission Delayed................................................................................ 10
I
7th Chapter:Code Types............................................................................ 11

All Code Types..........................................................................................................11
Decode Length Settings...........................................................................................11
1D Code types...........................................................................................................11
2D Code Types..........................................................................................................11
Codabar.....................................................................................................................12
Enable/Disable......................................................................................................12
Start/Stop Bit.........................................................................................................12
Check Bit................................................................................................................12
Cascade..................................................................................................................12
Decode Lenth Setting............................................................................................13
Code 39 .....................................................................................................................13
Enable/Disable.......................................................................................................13
Start/Stop Bit.........................................................................................................13
Check Bit................................................................................................................13
Decode Length Setting..........................................................................................14
Code 32 Pharmaceutical (PARAF) ...........................................................................14
Enable/Disable........................................................................................................14
Interleaved 2 of 5.......................................................................................................14
Enable/Disable.......................................................................................................14
Check Bit.................................................................................................................14
Decode Length Setting...........................................................................................15
NEC 2of5 ....................................................................................................................15
Enable/Disable........................................................................................................15
Check Bit..................................................................................................................15
Decode Length Setting...........................................................................................15
Code 93 .....................................................................................................................16
Enable/Disable.......................................................................................................16
Straight 2 of 5 Industrial (three-bar start/stop)......................................................16
Enable/Disable.......................................................................................................16
Straight 2 of 5 IATA (two-bar start/stop).................................................................17
Enable/Disable......................................................................................................17
Decode Length Setting.........................................................................................17
Matrix 2 of 5...............................................................................................................17
Enable/Disable......................................................................................................17
Decode Length Setting .........................................................................................17
Code 11......................................................................................................................18
II
Enable/Disable.....................................................................................................18
Check Bits.............................................................................................................18
Code 128 ..................................................................................................................18
Enable/Disable......................................................................................................18
ISBT 128 Cascade..................................................................................................19
UPC-A........................................................................................................................19
Enable/Disable......................................................................................................19
Check Bits..............................................................................................................19
Digital System.......................................................................................................19
Supplementals......................................................................................................20
Necessary Supplementals....................................................................................20
Supplementals Separator....................................................................................20
GS1-128.....................................................................................................................20
Enable/Disable......................................................................................................20
UPC-E0......................................................................................................................21
Enable/Disable......................................................................................................21
Barcode Expand...................................................................................................21
Necessary Supplementals...................................................................................21
Check Bits..............................................................................................................22
Digital System.......................................................................................................22
Supplementals......................................................................................................22
UPC-E1......................................................................................................................22
EAN/JAN-13...............................................................................................................23
Enable/Disable......................................................................................................23
Check Bits..............................................................................................................23
Supplementals.....................................................................................................23
Necessary Supplementals...................................................................................24
ISBN Translate.........................................................................................................24
EAN/JAN-8.................................................................................................................24
Enable/Disable......................................................................................................24
Check Bits..............................................................................................................24
Supplementals......................................................................................................25
Necessary Supplementals....................................................................................25
III
MSI............................................................................................................................25
Enable/Disable.....................................................................................................25
Check Bits.............................................................................................................26
Decode Length Settings.......................................................................................26
GS1 DataBar Omnidirectional................................................................................26
Enable/Disable.....................................................................................................26
GS1 DataBar Limited...............................................................................................26
Enable/Disable.....................................................................................................26
GS1 DataBar Expanded ..........................................................................................27
Enable/Disable.....................................................................................................27
Decode Length Settings.....................................................................................27
PDF417.....................................................................................................................27
Enable/Disable.....................................................................................................27
Decode Length Settings......................................................................................27
QRC ODE .................................................................................................................28
Enable/Disable.....................................................................................................28
Data Matrix..............................................................................................................28
Enable/Disable.....................................................................................................28
Aztec Code ..............................................................................................................29
Enable/Disable.....................................................................................................29
China Post (Hong Kong 2 of 5)................................................................................29
Enable/Disable....................................................................................................29
Korea Post................................................................................................................30
Enable/Disable.....................................................................................................30
Check Bits.............................................................................................................30
Han Xin code ...........................................................................................................31
Enable/Disable.....................................................................................................31
Maxi code.................................................................................................................31
Enable/Disable.....................................................................................................31
M ICROPDF ........................................................................................... ..................32
Enable/Disable.....................................................................................................32
IV
GS1 Composite Codes...........................................................................................32

Enable/Disable...................................................................................................32
Decode Length Settings....................................................................................32
Codablock A...........................................................................................................33
Enable/Disable...................................................................................................33
Decode Length Settings....................................................................................33
Codablock F...........................................................................................................33
Enable/Disable...................................................................................................33
Decode Length Settings.....................................................................................33
8th Chapter: Other Function Settings......................................................34

Software Version Display.....................................................................................34
Image Mirror.........................................................................................................34
Code Reverse........................................................................................................34
Safe Mode.............................................................................................................34
QR Code Website Setting.....................................................................................34
Code ID Prefix.......................................................................................................34
Keyboard Language Settings..............................................................................35
USA....................................................................................................................35
FINLAND............................................................................................................35
SPAIN.................................................................................................................35
FRANCE.............................................................................................................35
GERMANY..........................................................................................................35
ITALY.................................................................................................................35
DENMARK..........................................................................................................35
NORWAY............................................................................................................35
ICELAND.............................................................................................................35
CZECH...............................................................................................................35
HUNGARY..........................................................................................................35
SWEDEN............................................................................................................35
ARAB..................................................................................................................35
RUSSIA..............................................................................................................35
SWITZERLAND_FRENCH..................................................................................35
SLOVENIA..........................................................................................................35
CROATIA............................................................................................................36
ALBANIA............................................................................................................36
SERBIA_LATIN..................................................................................................36
SERBIA_CYRILLIC.............................................................................................36
CZECH_QWERTZ..............................................................................................36
V
CZECH_QWERTY...............................................................................................36
DUTCH...............................................................................................................36
ESTONIA............................................................................................................36
LITHUANIA.........................................................................................................36
IRISH..................................................................................................................36
FAEROESE.........................................................................................................36
TURKEY_F..........................................................................................................36
TURKEY_Q..........................................................................................................36
JAPAN_ASCII......................................................................................................36
Chinese Keyboard Setting...................................................................................37
Chinese Output Format.......................................................................................37
Case Switch..........................................................................................................37
9th Chapter:FAQ & Solutions.................................................................38

10th Chapter:Equipment Maintanence................................................38
Appendix 1：Code Types ID Table....................................................................39
Code Type ID Table...............................................................................40
Postal Code............................................................................................40
Appendix 2：ASCI I Transform...........................................................................41
Appendix 3：Special Setting Codes..................................................................44
Appendix 4：ASCII Transform In Keyboard Operation....................................45
VI
1st Chapter:Introduction
This user manual are applied for our 2D desktop barcode scanner which based
on 2D image scanning to identify 1D and 2D barcodes. They apply a complete set
of newly developed patented technologies and have strong recognition performance.
Support automatic continuous scanning mode, fast and flexible.
This chapter will introduce the method of using the product step by step with
the picture. Please compare the actual product you have purchased when reading the
document, so that it is more conducive to your understanding of this document.
This chapter is applicable to ordinary users, maintenance personnel and software
developers.
2nd Chapter:Product Features

* Research and development independently, with a full set of patents,
plug and play without installing drivers.
*The wide voltage design avoids the situation that data transmission
cannot be uploaded due to voltage fluctuations.
*The 32-bit main control chip is equipped with patented software, which
can smoothly interpret reflective, wrinkled, blurred, and colored barcodes,
and can also decode normally in strong light and dark light environments.
*Support RS232, USB, USB-COM, multiple interfaces to ensure
compatibility with your existing and future terminals.
*Smooth and coordinated appearance can reduce user fatigue, make the
operation extremely comfortable, and improve work efficiency significantly
1
3rd Chapter:Parameters
Electrical Parameters
Interfaces：USB.USB-COM.RS232(Optional) Power Voltage：5V
Current Consumption：±10% Curent of Power ON：360mA
Stanby Current：193mA Working Current：335mA
Physical Parameter
Light Source：Red LED light Accuracy：≥3mil
Resolution：640 pixels (H) x 480 pixels (V) Scan Angle：65°(Pitch)，65°(Tilt)，360°(Rotate)
Environment
Working Temperature：0°C to 40°C (32°F to 104°F)
Storage Temperature：-30°C to 60°C (-22°F to 140°F)
Humidity：5% to 95% (Non-condensing)
Ambient Light：It will not affect the normal office and factory lighting environment or direct
exposure to sunlight
Drop Test: Can withstand the impact of multiple drops from a height of 1.5 meters to
mixed ground
Electrostatic Discharge: Meet the requirements of 15kV air discharge and 8kV contact discharge
Decode Ability
1D: Codabar、Code 39、Code 32 Pharmaceutical (PARAF)、Interleaved
2 of 5、NEC 2 of 5、Code 93、Straight 2 of 5 Industial、Straight 2 of 5 IATA，Matrix
2 of 5，Code 11、Code 128、GS1-128、UPC-A、UPC-E、EAN/JAN-8、EAN/JAN-13、
MSI、GS1 DataBar Omnidirectional、GS1 DataBar Limited、GS1 DataBar
Expanded、China Post(Hong Kong 2 of 5)、Korea Post
2D: PDF417, QR code, Matrix 2 of 5, MicroPDF417, Australian Post, Canada
Post,Japan Post, MaxiCode, Codablock, Aztec, Dutch Post, DataMatrix, etc.
Default Enable Code types: Aztec、Codabar、Code39、Code93、Code128、Data Matrix、
EAN/JAN-8、EAN/JAN-13、GS1-128、GS1-DataBar、Interleaved2of5、NEC2of5、
PDF417、QR Code、UPC-A、UPC-E0
Depth of Scan
Code39(5mil)：0-9cm Code39(13mil)：0-17.5cm
UPC-A(13mil)：1-17cm QR(20mil)：0-13cm
QR(30mil)：0-18cm Alipay Payment Code(QR 3*3)：1-32cm
Wechat Payment Code(QR 2.3*2.3)：0-28cm
*Min distance of scanning depend of scan angle and code length

*Payment code of Alipay and Wechat depeng on the phone brightness
2
Appearance
Button
Fill Light
Scan Window
USB Interface
Buzzer
3
Factory Default Setting

If you want to apply the factory default settings to the barcode scanner, scanning
following setting code,the "Factory Default Setting" barcode.
(800006.)
Factory Default Setting
4nd Chapter: Interfaces

Introduction
Introducing USB and RS232 interfaces and their related configurations in this chapter.
RS232
Scanning setting code“RS232”barcode to connect with host via serial.
Serial interface default configuration:Baud Rate: 115200; Data Bit: 8; Parity Bit: none;
Stop Bit: 1, Ending Character: CR+LF
(8810010.)
RS232
RS232 Baud Rater
Baud rate: Send data from the barcode scanner to the terminal at the specified rate.
The terminal must be set to the same baud rate as the barcode scanner to
communicate normally. Default=115200
(8310030.) (8310031.)
300 600
(8310032.) (8310033.)
1200 2400
(8310034.) (8310035.)
4800 9600
4
(8310036.) (8310037.)
19200 38400
(8310038.) (8310039.)
57,600 *115,200
RS232 ：Data Bits,Stop Bits,Parity
(8310063.) (8310060.)
Data Bits:7, Stop Bits:1, Even Parity Data Bits:7, Stop Bits:1, Parity:None
(8310066.) (8310064.)
Data Bits:7, Stop Bits:1, Odd Parity Data Bits:7, Stop Bits:2, Even Parity
(8310061.) (8310067.)
Data Bits:7, Stop Bits:2, Parity:None Data Bits:7, Stop Bits:2, Odd Parity
(8310065.) (8310062.)
Data Bits:8, Stop Bits:2, Even Parity * Data Bits:8, Stop Bits:1, Parity:None
(8310068.)
Data Bits:8, Stop Bits:1, Odd Parity
5
USB
USB HID
Scan the following bar code to configure the bar code scanner to USB HID Keyboard
mode. CR and LF are added by default
(881001124. )
USB HID
USB COM
Scan following barcode to configure the bar code scanner to USB-COM mode,and
emulate the conventional COM port which is based on RS232. If your host are used
Microsoft Windows system, you need to download the driver. If your host are used
Apple Macintosh system, the computer will recognize the barcode scanner as a
USBCDC device automatically.
(881001133.)
USB COM
Note: No additional configuration is required（E.g.:Baud Rate)
5rd Chapter:Input/Output Settings

Introduction
Introduce the configuration of the buzzer and LED when the barcode
scanner is electrified, decoded, and pressed.
Buzzer Setting when Electrifying

Scan following setting codes to choose buzzer on or off of when barcode
scanner get electrified.Default setting is buzzer ON.
（8410130.） (8410131.)
Buzzer OFF * Buzzer ON
6
Buzzer Setting when Decode successfully

Buzzer ON or OFF Setting
Scan following setting codes to choose buzzer on or off of when decode successfully.
Default setting is buzzer on.
(8410010.) (8410011.)
Buzzer OFF *Buzzer ON
Volume Settings
Scan the following setting code to choose the volume of buzzer of when decode
successfully.Default setting is high.
(8410091.) (8410092.)
Low Middle
(8410093.) (8410090.)
*High OFF
Frequency Settings
Scan the following setting codes to choose the buzzer frequency of when decode
successfully.Default setting is middle
(8410061600.) (8410062400.) (8410064200.)

Low( 1600 Hz) * Middle( 2400 Hz) High(4200 Hz)
Beep Status Setting after Decoding Successfully

Scan following setting code to choose normal beep or short beep of when decode
successfully.Default setting is normal beep.
(8410020.) (8410021.)
* Normal Beep Short Beep
7
Output Delayed
Scan following setting codes to choose time interval between 1st scanning and
next scanning. Default time interval is 750ms.
(8510060.) (851006350.)
No Delay (350 ms)
(851006750.) (8510061000.)
( 750 ms) ( 1, 000 ms)
Lighting Setting
(8980051.) (8980050.)
ON OFF
Standby Setting
5s（Default） 1Minutes
3Minutes 5Minutes
Never Standby
8
6th Chapter:Data Editing

Prefix/Suffix Settings
Note:Add up to 10 characters as prefix and suffix to each barcode
1:Add customize prefix or suffix to all code types.
E.g.1:Add XYZ as prefix or suffix:
Step 1:Checking Appendix 1: the HEX value of all code is 99.
Step 2:Checking Appendix 2: the HEX value of X Y Z are 58,59,5A.
Step 3:Scanning setting code“Add Prefix”or “Add Suffix”in page 16.
Step 4:Find the setting codes corresponding to 9, 9, 5, 8, 5, 9, 5, A in Appendix 3 and scan them
one by one
Step 5:Scanning setting code“Save”in page 17.
Note:If an error occurs while scanning the setup code in Appendix 3,scan setting code
"Abandon", and repeat step 3.
2:Add customize prefix or suffix for a specific code type.
E.g.2:Add Q as prefix for QR code.
Step 1:Checking Appendix 1:the HEX value of QR code is 73
Step 2:Checking Appendix 2:the HEX value of Q is 51
Step 3:Scanning setting code“Add Prefix”or “Add Suffix”in page 16.
Step 4:Find setting codes corresponding to 7, 3, 5,1 in Appendix 3 and scan them one by one
Step 5:Scanning setting code“Save”in page 17.
3:Cancel customize prefix or suffix for a specific code type
E.g.3:Cancel customize prefix or suffix for QR code.
Step 1:Checking Appendix 1:the HEX value of QR code is 73
Step 2:Scan setting code“Clear Prefix for one code”or “Clear Suffix for one code”in page 16
Step 3:Find setting codes corresponding to 7, 3 in Appendix 3 and scan them one by one
Note:If you need to cancel the prefix or suffix of all code types, please scan setting code"Clear
All Prefix"or"Clear All Suffix".
(889002.) (888002.)
Add Prefix Add Suffix
(889004.) (888004.)
Clear Prefix for one code Clear Suffix for one code
(889003.) (888003.)
Clear All Prefix Clear All Suffix
(800002.) (800000.)
Save Abandon
9
Ending Character Settings
(890000.) (888002990A.)
CR(Carriage Return) LF(Line Feed)
(888002990D0A.)
CR+LF
Keyboard Operation
E.g.1：Setting all code types adding keyboard operation.
Step 1:Checking Appendix 1:the HEX value of all barcode types is 99
Step 2:Checking Appendix 4:the HEX value of save is 13 in keyboard operation ASCII transform.
Step 3:Scanning following setting code”Start Keyboard Operation”
Step 4:Find setting codes corresponding to 9,9,1,3 in Appendix 3 and scan them one by one
Step 5:Scanning setting code“Save”
（8210042）（8210040）
Start Keyboard Operation Stop Keyboard Operation
Function Code Transmission Setting

When the function characters transmission is enabled and the data of code contains
the function characters, the barcode scanner will transmit the data of function
character to the terminal.Default setting is enable.
(8000051.)
Enable
(8000050.)
Disable
Data Transmission Delayed
E.g.1：Setting data transmission 100ms delayed
Step 1:Scanning setting code“Data Transmission Delayed”in page 18
Step 2:Find setting codes corresponding to 2, 0 in Appendix 3 and scan them one by
one(Why 2,0? Because 100/5=20,if setting 150ms delayed,it will be 3,0)
Step 3:Scanning setting code“Save”in page 18
(851004.)
Data Transmission Delayed
10
7th Chapter:Code Types

All Code Types
Scan following setting codes to choose all code types enabled or disabled.
(9990011.) (9990010.)
Enable All Codes Disable All Codes
Notes:1:It also can read setting codes in this manual after scanning setting code
“Disable All Codes”.
2:It can not read 2D postal code even scanning setting code“Enable All Code”
Scanning setting code“Enable”of 2D postal code in page
3:If you need the scanner only read one or several code types,scanning“Disable
All Codes”and then scanning “Enable”of those code types.
Decode Length Settings
Introduction:The effective reading length of some code types can be set. If the data
length of the code does not match the effective reading length, the barcode scanner
will beep specially to show the error. If setting the same value for the minimum and
maximum length, the bar code scanner will only read a code of a fixed length. It helps
reduce misreading.
E.g.: Setting Code 93 code decode length as 06-10 characters
Minimum Length=06,Maximum Length=10
Step 1:Scanning setting code“Min Decode Length”of Code 93 in page 24
Step 2:Find the setting code corresponding to 6 in Appendix 3 and scan it
Step 3:Scanning setting code“Save”.
Step 4:Scanning setting code“Max Decode Length”of code 93 in page 24
Step 5:Find the setting code corresponding to 1,0 in Appendix 3 and scan them one by one
Step 6:Scanning setting code“Save”.
Done
1D Code types
(9950040.) (9950041.)
Enable All 1D Code Disable All 1D Code
2D Code Types
(9950070.) (9950071.)
Enable All 2D Code Disable All 2D Code
11
Codabar
(900000.)
Default All Codabar Settings
Enable/Disable
(9000031.)
Enable
（9000030.）
Disable
Start/Stop Bit
Scan following setting code to select whether to transmit or not to transmit the
start/stop bits.Default setting is disable transmit.
(9000061.) (9000060.)
Enable Transmit Disable Transmit
Check Bit
(9000010.) (9000011.) (9000012.)

No Check Bit Disable Transmit Check Bit EnableTransmit Check Bit
Cascade
When barcode cascading is enabled, the barcode scanner will look for a barcode with a "D"
character at the beginning and a neighboring barcode with a "D" character at the end. In this
case, the two barcodes will form one barcode, and ignore all the "D" characters in the barcode
A 1 2 34D D 5 6 7 8A
(9000021.) (9000022.) (9000020.)

ON Need OFF
ON：Barcode Scanner not only read normal codabar codes,but also cascaded codabar code
Need：Scanning”Need”after scanning “ON”,the scanner will only read cascaded
codabar codes
OFF：Barcode Scanner will not read cascaded codabar codes.
12
Decode Lenth Setting

Scanning following setting code to modify the min or max decode length of
Codabar.Refer to page 19“Decode Length Settings”.
Default setting min decode length is 4,max is 60.
Min decode length is 2,max is 60
(900005.) (900004.)
Min Decode Length Max Decode Length
Code 39
(901000.)
Default All Code 39 Settings
Enable/Disable
(9010011.) (9010010.)
Enable Disable
Start/Stop Bit
Scan following setting code to select whether to transmit or not to transmit the
start/stop bits.Default setting is disable transmit.
(9010091.) (9010090.)
Enable Transmit Disable Transmit
Check Bit
(9010040.) (9010041.) (9010042.)

No Check Bit Disable Transmit Check Bit Enable Transmit Check Bit
13
Decode Length Setting

Code 39.Refer to page 19“Decode Length Settings”.
Min decode length is 0,max is 48.
(901008.) (901007.)
Code 32 Pharmaceuti cal ( PARAF)

Code 32is a form of Code 39 barcode and used on Italian medicines.When configuring
code32, you need to enable code39 first.
Code 32 isalso named PARAF
(9010051.) (9010050.)
Enable Disable
I nt erl eaved 2 of 5
(902000.)
Default All Interleaved 2 of 5 Settings
Enable/Disable
(9020021.) (9020020.)
Enable Disable
Check Bit
(9020010.) (9020011.) (9020012.)

14

Interleaved 2 of 5.Refer to page 19“Decode Length Settings”.
(902004.) (902003.)
NEC 2of 5
(903000.)
Default All NFC 2 of 5 Settings
Enable/Disable
(9030011.)
Enable
(9030010.)
Disable
Check Bit
(9030020.) (9030021.) (9030022.)


NFC 2 of 5.Refer to page 19“Decode Length Settings”.
(903004.) (903003.)
15
Code 93
(904000.)
Enable/Disable
(9040021.) (9040020.)
Enable Disable
(904004.) (904003.)
Straight 2 of 5 Industrial ( three-bar start/ stop)
(905000.)
Default All Straight 2 of 5 Industrial Settings
Enable/Disable
(9050011.) (9050010.)
Enable Disable

Straight 2 of 5 Industrial.Refer to page 19“Decode Length Settings”.
(905003.) (905002.)
16
Straight 2 of 5 IATA (two- bar start/ stop)
(906000.)
Default All Straight 2 of 5 IATA Settings
Enable/Disable
(9060011.) (9060010.)
Enable Disable

Straight 2 of 5 IATA.Refer to page 19“Decode Length Settings”.
(906003.) (906002.)
Matri x 2 of 5
(907000.)
Default All Matrix 2 of 5 Settings
Enable/Disable
(9070011.) (9070010.)
Enable Disable
Matrix 2 of 5.Refer to page 19“Decode Length Settings”.
(907003.) (907002.)
17
Code 11
(908000.)
Enable/Disable
(9080021.) (9080020.)
Enable Disable
Check Bits
(3110280.) (3110281.)
One Check Bit Two Check Bits

(908004.) (908003.)
Code 128
(909000.)
Enable/Disable
(9090011.) (9090010.)
Enable Disable
18
ISBT 128 Cascade
(9020051.) (9020050.)
ISBT 128 Enable *ISBT 128 Disable
(909003.) (909002.)
UPC-A
(912000.)
Note:When UPC-A get disabled,it will be decode as EAN-13.
Enable/Disable
(9120031.) (9120030.)
Enable Disable
Check Bits
(9120041.) (9120040.)
Enable Disable
Digital System
(9120051.) (9120050.)
Enable Disable
19
Supplementals
Scanning following setting code to select enable or disable 2 or 5 supplementals
Default setting is 2 and 5 supplementals disabled.
(9120011.) (9120010.)
2 Supplementals ON 2 Supplementals OFF
(9120021.) (9120020.)
Necessary Supplementals
The barcode scanner only read UPC-A with supplementals after it read following
setting code“Enable”.And at this case,you need to enable 2 or 5 supplementals.
Default setting is disable.
(9120061.) (9120060.)
Enable Disable
Supplementals Separator
(9120071.) (9120070.)
Enable Disable
Notes：
Scanning following setting codes to select tranmit or not transmit UPC-A to EAN-13
(9120111.) (9120110.)
Not Transmit Transmit
GS1- 128
(910000.)
Enable/Disable
Default All GS1-128 Settings
(9100011.) (9100010.)
Enable Disable
20

GS1-128.Refer to page 19“Decode Length Settings”.
(910003.) (910002.)
UPC- E0
(914000.)
Default All UPC-E0 Settings
Enable/Disable
Most of UPC code is started with 0,getting it enabled before scanning those code.
If need to read UPC code which is started with 1,getting UPC-E1 enabled.
Default setting is enable.
(9140101.) (9140100.)
Enable Disable
Barcode Expand
Scanning following setting code to select whether expanding UPC-E to UPC-A
(9140021.) (9140020.)
Enable Disable
It will only read UPC-E codes which with supplementals after scanning following
setting code”Enable”.
。
(9140031.) (9140030.)
Enable Disable
There is a space after scanning following setting code”Enable”.
Default setting is enable.
(9140041.) (9140040.)
Enable Disable
21
Check Bits
Scanning following setting to select whether transmit last check bit.
(9140051.) (9140050.)
Enable Disable
Digital System
UPC digital system will be transfered in front of barcode data.
(9140061.) (9140060.)
Enable Disable
Supplementals
Scanning following setting code to select enable or disable 2 or 5 supplementals.
Default setting is 2 or 5 supplementals disabled.
(9140071.) (9140070.)
(9140081.) (9140080.)
UPC-E1
Enable/Disable
Most of UPC code is started with 0,getting it enabled before scanning those code.
If need to read UPC code which is started with 1,getting UPC-E1 enabled.
Default setting is disable.
(9140091.) (9140090.)
Enable Disable
22
EAN/ JAN- 13
(915000.)
Default All EAN/JAN-13 Settings
Enable/Disable
(9150011.) (9150010.)
Enable Disable
Check Bits
(9150021.) (9150020.)
Enable Disable
Supplementals
Scanning following setting code to select enable or disable 2 or 5 supplementals.
Default setting is 2 or 5 supplementals disabled.
(9150031.) (9150030.)
(9150041.) (9150040.)
23
It only read EAN/JAN-13 code with supplementals after scanning following
setting code“Enable”.Default setting is disable.
(9150051.) (9150050.)
Enable Disable
There is a space between normal data and supplementals after scanning
following setting code”Enable”.Default setting is enable.
(9150061.) (9150060.)
Enable Disable
ISBN Translate
EAN-13 Bookland characters will be converted to the equivalent ISBN characters
format after scanning following setting code‘Enable’.Default setting is disable.
(9150071.) (9150070.)
Enable Disable
EAN/JAN- 8
(916000.)
Default All EAN/JAN-8 Settings
Enable/Disable
(9160011.) (9160010.)
Enable Disable
Check Bits
(9160021.) (9160020.)
Enable Disable
24
Supplementals
Scanning following setting code to select whether transmit 2 or 5 supplementals
of EAN/JAN-8 code.Default setting is disable.
(9160031.) (9160030.)
(9160041.) (9160040.)
Barcode scanner only read EAN/JAN-8 code which with supplementals after
scanning following setting code”Enable”.Default setting is disable.
(9160051.) (9160050.)
Enable Disable
There is a space between normal data and supplementals data after scanning
following setting code”Enable”.Default setting is enable.
(9160061.) (9160060.)
Enable Disable
MSI
(917000.)
Default All MSI Settings
Enable/Disable
(9170011.)
Enable
(9170010.)
Disable
25
Check Bits
(9170020.) (9170021.) (9170026.)

Disable Transmit Check Bits Enable Transmit Check Bits No Check Bits

MSI.Refer to page 19“Decode Length Settings”.
(917004.) (917003.)
GS1 DataBar Omnidirecti onal
(918000.)
Default All GS1 DataBar Omnidirectional Settings
Enable/Disable
(9180011.) (9180010.)
Enable Disable
GS1 DataBar Limited
(919000.)
Default All GS1 DataBar Limited Settings
Enable/Disable
(9190011.) (9190010.)
Enable Disable
26
GS1 DataBar Expanded
（920000.）
Deafult All GS1 DataBar Expanded Settings
Enable/Disable
(9200011.) (9200010.)
Enable Disable
GS1 DataBar Expanded.Refer to page 19“Decode Length Settings”.
(920003.) (920002.)
PDF417
(924000.)
Default All PDF417 Settings
Enable/Disable
(9240011.) (9240010.)
Enable Disable
PDF-417.Refer to page 19“Decode Length Settings”.
(924003.) (924002.)
27
Data Matrix
(930000.)
Default All Data Matrix Settings
Enable/Disable
(9300011.) (9300010.)
Enable Disable
Data Matrix.Refer to page 19“Decode Length Settings”.
(930002.) (930003.)
QRCode
(928000.)
Enable/Disable Default All QRCode Settings
Following setting codes both work for QR code and Micro QR code.
(9280011.) (9280010.)
Enable Disable
QR code.Refer to page 19“Decode Length Settings”.
(928003.) (928002.)
28
Aztec Code
(931000.)
Default All Aztec Code Settings
Enable/Disable
(9310011.) (9310010.)
Enable Disable

Aztec Code.Refer to page 19“Decode Length Settings”.
(931003.) (931002.)
China Post ( Hong Kong 2 of 5)
(936000.)
Default All China Post ( Hong Kong 2 of 5) Settings
Enable/Disable
(9360011.) (9360010.)
Enable Disable
29

China Post ( Hong Kong 2 of 5).Refer to page 19“Decode Length Settings”.
(936003.) (936002.)
Korea Post
(937000.)
Default All Korea Post Settings
Enable/Disable
(9370011.) (9370010.)
Enable Disable

Korea Post Code.Refer to page 19“Decode Length Settings”.
(937003.) (937002.)
Check Bits
(9370041.) (9370040.)
Enable Disable
30
Han Xin code
(932000.)
Default All Han Xin code Settings
Enable/Disable
(9320011.) (9320010.)
Enable Disable
HanXin Code.Refer to page 19“Decode Length Settings”.
(932003.) (932002.)
Maxi code
(929000.)
Default All Maxi code Settings
Enable/Disable
(9290011.) (9290010.)
Enable Disable
Maxi Code.Refer to page 19“Decode Length Settings”.
(929003.) (929002.)
31
Micropdf
(925000.)
Default All Micropdf Settings
Enable/Disable
(9250011.) (9250010.)
Enable Disable
Micropdf code.Refer to page 19“Decode Length Settings”.
(925003.) (925002.)
GS1 Composite Code
(926000.)
Default All GS1 Composite Code Settings
Enable/Disable
(9260011.) (9260010.)
Enable Disable

GS1 Composite Code .Refer to page 19“Decode Length Settings”.
(926004.) (926003.)
32
Codablock A
(922000.)
Default All Codablock A settings
Enable/Disable
(9220011.) (9220010.)
Enable Disable
Codablock A code.Refer to page 19“Decode Length Settings”.
(922003.) (922002.)
Codablock F
(923000.)
Default All Codablock F settings
Enable/Disable
(9230011.) (9230010.)
Enable Disable
Codablock F code.Refer to page 19“Decode Length Settings”.
(923003.) (923002.)
33
8th Chapter: Other Function Settings

Software Version Display
Scanning following setting code”Version Display”and version information of
software will be display in terminals.
(809005.)
Image Mirror
Version Display
(8960271.) * (8960270.)
Code Reverse
Enbale Disable
*(8910010.) (8910011.) (8910012.)

Do not Support Reverse Code Only Support Reverse Code Both Supported
If need to set supporting normal code and reverse code after scanning setting code”
Only Support Reverse Code”,You can scanning following setting code”Both Supported”.
(8910012.)
Safe Mode Both Supported
(8000050.) *(8000051.)
Setting Code Function OFF Setting Code Function ON
QR Code Website Setting
(9950061.) (9950060.)
OFF ON
Code ID Prefix
(889002995C80.)
Add Serial Number as Prefix
34
Keyboard Language Settings

USA FINLAND
（8210010.）（8210012.）
SPAIN FRANCE
（82100110.）（8210013.）
GERMANY ITALY
（8210014.）（8210015.）
DENMARK NORWAY
（8210018.）（8210019.）
ICELAND CZECH
（82100175.）（82100115.）
HUNGARY SWEDEN
（82100119.）（82100123.）
ARAB RUSSIA
（82100191.）（82100126.）
SWITZERLAND_FRENCH SLOVENIA
（82100129.）（82100131.）
35
CROATIA ALBANIA
（82100132.）（82100135.）
SERBIA_LATIN SERBIA_CYRILLI C
（82100136.）（82100137.）
CZECH_QWERTZ CZECH_QWERTY
（82100138.）（82100139.）
DUTCH ESTONIA
（82100111.）（82100141.）
LITHUANIA IRISH
（82100144.）（82100173.）
FAEROESE TURKEY_F
（82100183.）（82100127.）
TURKEY_Q
（82100124.）
JAPAN_ASCII
(8210083.) （ 82100128.）
You need to scan following two setting codes when you want input Japanese in word software.
36
Chinese Keyboard Setting

In keyboard mode, you need to scan the following setting code"Chinese Keyboard" to
open the Chinese keyboard (open by default), and then select the Chinese output format.
* (82100190.)
Chinese Keyboard
Chinese Output Format

The Chinese output format of keyboard mode is divided into GBK, UNICODE, and the
default is GBK.
1.GPK format(Output in TXT,excel and wps),scanning following setting code”GBK”
*(8210131.)
GBK
2. UNICODE format( Output in word) , scanning following setting code”UNICODE”
(8210132.)
UNICODE
Case Switch
All Lowercase
All caps
No Case Switch
Case swap
37
9th Chapter:FAQ & Solutions

Q：Barcode scanner does not work?
Solution 1.It does not get electrified.
Solution 2.Using the wrong cable,please use the right cable from original factory
Solution 3.The cable interface is loose and reconnect.
Solution 4.Please checking if the trigger is ok.
Q：It can read codes,but can not transfer data to my device?

Solution 1.The cable interface is loose and reconnect.
Solution 2.Barcode scanner may not be configured to the correct terminal display.
Solution 3.If you are using a USB to RS232 cable and the data is garbled during data
output, it may be the data receiving speed of the device does not match the output
speed of the barcode scanner.
Q：It can read some code types,but some can not?
Solution 1. The barcode is defective. Try to scan the same type test barcode to check
if it can be decoded.
Solution 2. The distance between the barcode scanner and the code is inappropriate.
Please move the barcode closer or further away.
Solution 3.Please confirm that you have enabled the code type.
Q：It can not decode your code at some case?

Solution 1. Turn off the scanner,and making scanner and your device connected
correctly. Testing again.
Solution 2.If you can not solve the problem with the scanner,please contact with us.
10th Chapter:Equipment Maintanence

1. Dirt and dust on the scanning window sometimes affect the normal operation of the
barcode scanning device. When cleaning, you should use a good quality facial tissue to
gently wipe, or use a soft cloth to clean. If the paper with poor paper quality is used for
wiping for a long time, it will damage the surface finish of the window and affect the
reading effect of the barcode scanning device.
2. The outer shell of the barcode scanning device can be wiped with a clean soft cloth.
If necessary, a small amount of detergent can be added to the water and wiped with a
soft cloth dipped in water.
3. Do not spray any liquid on the window.
4. The scanning window must be kept clean, and the supplier is exempt from warranty
for damage caused by improper maintenance.
38
Appendix 1：Code Types ID Table

Code Type HEX ID
All Symbologies 99
Codabar 61 a
Code 11 68 h
Code 128 6A j
Code 32 Pharmaceutical (PARAF) 3C <
Code 39 (supports FullASCII mode) 62 b
TCIF Linked Code 39 (TLC39) 54 T
Code 93 and 93i 69 i
EAN 64 d
EAN-13(including Bookland EAN) 64 d
EAN-13 with Add-On 64 d

EAN-13 with Extended Coupon Code 64 d
EAN-8 44 D
EAN-8 with Add-On 44 D
GS1
GS1DataBar 79 y
GS1 DataBar Limited 7B {
GS1 DataBar Expanded 7D }

GS1-128 49 I
2 of 5
China Post (Hong Kong 2 of 5) 51 Q
Interleaved 2 of 5 65 e
Matrix 2 of 5 6D m
NEC 2 of 5 59 Y
Straight 2 of 5IATA 66 f
Straight 2 of 5 Industrial 66 f
MSI 67 g
Telepen 74 t
UPC
UPC-A 63 c
UPC-A with Add-On 63 c
UPC-A with Extended Coupon Code 63 c
UPC-E 45 E
UPC-E withAdd-On 45 E
UPC-E1 45 E
Add Newtologic Code ID 5C 80

Add AIM Code ID 5C 81
Add Backslash 5C 5C
Batch Mode Quantilty 35 5
39
Code Type ID Table

Code Type HEX ID
AllSymbologies 99
Aztec Code 7A z
Chinese Sensible Code (Han Xin Code) 48 H
Codablock A 56 V
Codablock F 71 q
Code 49 6C I
Data Matrix 77 w
GS1 79 y
GS1Composite 79 y
GS1 DataBar Omnidirecti onal 79 y
MaxiCode 78 x
PDF417 72 r
MicroPDF417 52 R
QR Code 73 s
Micro QR Code 73 s
Postal Code
Code Type HEX ID
All Symbologies 99
Australian Post 41 A
British Post 42 B
Canadian Post 43 C
Code Type HEX ID

China Post 51 Q
InfoMail 2c ,
Intelligent Mail Bar Code 4D M
Japanese Post 4A J
KIX (Netherlands) Post 4B K
Korea Post 3F ?
Planet Code 4C L
Postal-4i 4E N
Postnet 50 P
40
Appendix 2：ASCI I Transform

HEX Dec Character
00 0 NUL （Null char.）
01 1 SOH （Start of Header）

02 2 STX （Start of Tex）
03 3 ETX （End of Tex）
04 4 EOT （End of Transmission)
05 5 ENQ （Enquiry）
06 6 ACK （Acknowledgment)
07 7 BEL （Bell）
08 8 BS （Backspace
09 9 HT （Horizontal Tab
0a 10 LF （Line Feed）
0b 11 VT （Vertical Tab）
0c 12 FF （Form Feed）
0d 13 CR （Carriage Return)
0e 14 SO （Shift Out）
0f 15 SI （Shift In）
10 16 DLE （Data Link Escape)
11 17 DC1 （XON）（Device Control 1)
12 18 DC2 （Device Control 2)
13 19 DC3 （XOFF）（Device Control 3)
14 20 DC4 （Device Control 4)
15 21 NAK （Negative Acknowledgment)
16 22 SYN （Synchronous Idle)
17 23 ETB （End of Trans. Block)
18 24 CAN （Cance）
19 25 EM （End of Medium）
1a 26 SUB （Substitute)
1b 27 ESC （Escape）
1c 28 FS （File Separato）
1d 29 GS （Group Separator)
1e 30 RS （Request to Send)
1f 31 US （Unit Separator)
20 32 SP （Space）
21 33 ! （Exclamation Mark)
22 34 " （Double Quote)
23 35 # （Number Sign)
24 36 $ （Dollar Sign）
25 37 % （Percent）
26 38 & （Ampersand）
27 39 ` （Single Quote )
28 40 ( （Right / Closing Parenthesis）
41
29 41 ) （Right / Closing Parenthesis）

2a 42 * （Asterisk）
2b 43 + （Plus）
2c 44 , （Comma）
2d 45 - （Minus / Dash）
2e 46 . （Dot）
2f 47 / （Forward Slash）
30 48 0
31 49 1
32 50 2
33 51 3
34 52 4
35 53 5
36 54 6
37 55 7
38 56 8
39 57 9
3a 58 ：（Colon）
3b 59 ；（Semi-colon）
3c 60 < （Less Than）
3d 61 = （Equal Sign）
3e 62 > （Greater Than）
3f 63 ? （Question Mark）
40 64 @（AT Symbol)
41 65 A
42 66 B
43 67 C
44 68 D
45 69 E
46 70 F
47 71 G
48 72 H
49 73 I
4a 74 J
4b 75 K
4c 76 L
4d 77 M
4e 78 N
4f 79 O
50 80 P
51 81 Q
52 82 R
53 83 S
42
54 84 T
55 85 U
56 86 V
57 87 W
58 88 X
59 89 Y
5a 90 Z
5b 91 [ （Left / Opening Bracket)
5c 92 \ （BackSlash）
5d 93 ] （Right / Closing Bracket)
5e 94 ^ （Caret / Circumflex)
5f 95 _ （Underscore）
60 96 ' （Grave Accent )
61 97 a
62 98 b
63 99 c
64 100 d
65 101 e
66 102 f
67 103 g
68 104 h
69 105 i
6a 106 j
6b 107 k
6c 108 l
6d 109 m
6e 110 n
6f 111 o
70 112 p
71 113 q
72 114 r
73 115 s
74 116 t
75 117 u
76 118 v
77 119 w
78 120 x
79 121 y
7a 122 z
7b 123 { （Left/ Opening Brace）
7c 124 | （Vertical Bar）
7d 125 } （Right/Closing Brace）
7e 126 ~ （Tilde）
7f 127 DEL （Delete）
43
Appendix 3：Special Setting Codes
(K0K.) (K1K.) (K2K.)

0 1 2
(K3K.) (K4K.) (K5K.)

3 4 5
(K6K.) (K7K.) (K8K.)

6 7 8
(K9K.) (KAK.) (KBK.)

9 A B
(KCK.) (KDK.) (KEK.)

C D E
(KFK.) (800002.) (800000.)

F Save Abandon
Note: If there is an error when scanning letters or numbers (before scanning

the "Save" barcode), please scan the "Abandon" barcode, and then scan the
correct number or letter corresponding to the setting code, and finally scan
the "Save" barcode to save the settings
44
Appendix 4：ASCII Transform In Keyboard Operation

十六进制十进制 CTRL+X 说明
00 0 CTRL+@
01 1 CTRL+A Select All
02 2 CTRL+B Bold
03 3 CTRL+C Copy
04 4 CTRL+D Font Format
05 5 CTRL+E Align Center
06 6 CTRL+F Find
07 7 CTRL+G Positioning
08 8 CTRL+H Replace
09 9 CTRL+I Italic
0a 10 CTRL+J Justify
0b 11 CTRL+K Hyperlink
0c 12 CTRL+L Align Left
0d 13 CTRL+M Left Indent
0e 14 CTRL+N New Creation
0f 15 CTRL+O Open
10 16 CTRL+P Print
11 17 CTRL+Q
12 18 CTRL+R Align Right
13 19 CTRL+S Save
14 20 CTRL+T First Line Indent
15 21 CTRL+U Underline F12
16 22 CTRL+V Paste F1
17 23 CTRL+W Close Window F2
18 24 CTRL+X Cut F3
19 25 CTRL+Y Repeat F4
1a 26 CTRL+Z Undo F5
1b 27 CTRL+[ F6
1c 28 CTRL+\ F7
1d 29 CTRL+] F8
1e 30 CTRL+^ F9
1f 31 CTRL+- F10
7f 32 CTRL+
45
Version number

Kassen RS-720 EN

Uploaded by

Copyright:

Available Formats

Kassen RS-720 EN

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Kassen RS-720 EN

Uploaded by

Copyright:

Available Formats

2D Desktop Barcode Scanner

7th Chapter:Code Types............................................................................ 11

GS1 Composite Codes...........................................................................................32

8th Chapter: Other Function Settings......................................................34

9th Chapter:FAQ & Solutions.................................................................38

2nd Chapter:Product Features

*Min distance of scanning depend of scan angle and code length

Factory Default Setting

4nd Chapter: Interfaces

RS232 ：Data Bits,Stop Bits,Parity

5rd Chapter:Input/Output Settings

Buzzer Setting when Electrifying

Buzzer Setting when Decode successfully

(8410061600.) (8410062400.) (8410064200.)

Beep Status Setting after Decoding Successfully

6th Chapter:Data Editing

Ending Character Settings

Function Code Transmission Setting

7th Chapter:Code Types

(9000010.) (9000011.) (9000012.)

(9000021.) (9000022.) (9000020.)

Decode Lenth Setting

(9010040.) (9010041.) (9010042.)

Decode Length Setting

Code 32 Pharmaceuti cal ( PARAF)

(9020010.) (9020011.) (9020012.)

Decode Length Setting

(9030020.) (9030021.) (9030022.)

Decode Length Setting

Straight 2 of 5 Industrial ( three-bar start/ stop)

Decode Length Setting

Straight 2 of 5 IATA (two- bar start/ stop)

Decode Length Setting

Decode Length Setting

ISBT 128 Cascade

Decode Length Setting

(9170020.) (9170021.) (9170026.)

Decode Length Settings

GS1 DataBar Omnidirecti onal

GS1 DataBar Limited

GS1 DataBar Expanded

Decode Length Settings

China Post ( Hong Kong 2 of 5)

Decode Length Settings

Decode Length Settings

Han Xin code

GS1 Composite Code

Decode Length Settings

8th Chapter: Other Function Settings

*(8910010.) (8910011.) (8910012.)

Keyboard Language Settings

Chinese Keyboard Setting

Chinese Output Format

9th Chapter:FAQ & Solutions

Q：It can read codes,but can not transfer data to my device?

Q：It can not decode your code at some case?

10th Chapter:Equipment Maintanence

Appendix 1：Code Types ID Table