BSR 2021

General Notes Provincial Schedule of Rates 2021
01. As per the F.R. 425 of the Central Provincial Council, these standard rates are valid
from 01.01.2021 to 31.12.2021.
02. Value Added Tax (VAT) has not been included when preparing these rates. However,
if necessary, VAT can be added to the estimate by calculating 8% (or the approved
percentage) of the total value of Bill of Quantities (BOQ).
03. These rates were determined for all 03 districts of the Central Province, considering
the market prices in the last quarter of 2020 and the rates approved by the District
Price Committees.
04. The Building Schedule of Rates, Highway Schedule of Rates and the Irrigation
Schedule of Rates were initially prepared by Provincial Department of Engineering
Services, Provincial Road Development Authority (PRDA) and Provincial
Department of Irrigation respectively, and approved by the Provincial Price
Committee.
05. Building rates are valid for buildings up to four storeys only, highway rates are valid
for C, D, E and lower grade roads only and irrigation rates given are valid only for
minor irrigation work.
06. These rates have been prepared in accordance with the specifications approved by the
Construction Industry Development Agency (CIDA) and using materials conforming
to Sri Lanka Standards (SLS), British Standards (BS), American Standards (ASTM)
and Euro Standards (EURO). The approval of the Site Engineer shall be obtained
when it is required to use materials without their standards certified. Thus, the quality
of the construction work shall be ensured.
07. Approval has been granted for the use of certain major construction materials on the
request of some trading organizations after testing them under the supervision of the
Department of Engineering Services. The use of approved materials is recommended,
and in other cases it is the responsibility of the Engineer in charge to conduct proper
tests to ensure the quality of the materials.
08. The institution/ company carrying out the construction work shall take steps to ensure
the materials used meet the recommended standards. If additional tests are required as
per the engineering requirements, such expenses can be reimbursed only when the
materials tested meet the quality standards. In other cases the institution/ company
will have to bear the expenses of the tests.
09. The rates herein can be used to prepare Total Cost Estimates and to evaluate
competitive bids. These rates have been determined based on certain assumptions and
their accuracy may depend on many factors such as location of the site, availability of
materials, variation of labour wages, staff of the construction company, machinery,
financial capability, nature of other works being carried out by the company,
Provincial Price Committee 2021

restrictions of working hours per day, construction period, complexity of the
construction work, financial risk, risks of construction, constant financial flow etc.
Therefore competitive bidding shall be employed for procurement wherever
applicable.
10. Transport charges for a distance of 10km are included in the rates. If the materials
have to be transported for more than 10km additional transport charge should be
added to the rate.
11. In the execution of a specialized work under provisional sum the applicable
attendance fee factor shall be 8% only.
12. The rates column should be selected depending on the total cost of the project when
preparing the estimates. If the Total Cost is Rs. Three Million or higher, items coming
under preliminaries should be included in the bill of quantities as a separate bill to the
estimate.
13. These rates have been prepared using conventional rate analysis methods. Rates shall
be prepared by using a work study for works that require specialized equipment or
machinery. Soft copies and hard copies of such rates shall be submitted to the Deputy
Chief Secretary (Engineering Service) of Central Province for approval.
14. Overhead and profit percentages related to Special Schedule of Rates (SSR) or In-lieu
Schedule of Rates (ISR) may be determined on Pro Rata basis by analysing rates for
similar works or as per the Condition of Contracts of Standard Bidding Documents.
15. Your attention is drawn to construction related clauses of the Construction

Development Act, No.33 of 2014. Accordingly, all construction companies shall be
attentive in providing proper safety measures for the site workers. Construction sites
shall be kept clean and construction companies shall be made aware to prevent
breeding of mosquitoes. The approval of relevant institutions shall be obtained, any
threats to the environment shall be avoided and relevant Acts and Regulations and
Circulars shall be adhered to.
16. In order to avoid adverse effects of price variations to the construction process, price
variation formulae given in the Standard Bidding Documents shall be incorporated for
all construction works with a construction period exceeding three months (as per the
Standard Bidding Documents or NPA Guidelines). The estimates should be provided
with provisions enabling payments for price variations.
17. These rates are valid only for measure and pay works, quality controlled by the
Engineer. These rates are not valid for other types of construction works such as
works, quality assured by the contractor etc.

CONTENT
Page
Building Schedule of Rates -01 to 69
Highway Schedule of Rates -70 to 97
Irrigation Schedule of Rates -98 to 102
ANNEX - 01
Drawings
ANNEX - 02
Approved Construction Material Price for
2021
BUILDING SCHEDULE OF RATES - 2021
DEPARTMENT OF ENGINEERING SERVICES

CENTRAL PROVINCE
CONTENTS BUILDING SCHEDULE OF RATE
Page
-
GENERAL NOTES I to XIII
- DEMOLITION/ ALTERATION / REPAIR
SECTION C -1 to 6
AND MAINTENANCE
-
SECTION D EXCAVATION AND EARTH WORK -7 to 9
-
SECTION F CONCRETE WORKS -10 to 13
- MASONRY WORKS/BRICK WORK/
SECTION G -14 to 15
BLOCK WORK
-
SECTION H WATER PROOFING -16
- STRUCTURAL METAL WORKS FOR
STEEL IN FRAMED STRUCTURES/
SECTION J ALUMINUM IN FRAMED STRUCTURES/ -17 to 18
METAL WORK IN UNFRAMED
STRUCTURES
-
SECTION K METAL WORK -19 to 22
-
SECTION L WOOD WORK -23 to 27
- PARTITIONS/LININGS/SUSPENDED
SECTION N -28 to 29
CEILINGS
SECTION P - ROOF COVERING / ROOF PLUMBING - 30 to 32
-
SECTION Q PLUMBING / SANITARY INSTALLATION -33 to 36
-
SECTION R MECHANICAL INSTALLATIONS -37
-
SECTION S ELECTRICAL INSTALLATIONS -38 to 56
-
SECTION T FLOOR / WALL / CEILING FINISHES -57 to 59
-
SECTION U GLAZING / INFILL PANELS -60
-
SECTION V PAINTING -60 to 61
-
SECTION W DRAINAGE SYSTEMS -62 to 64
-
SECTION X EXTERNAL WORK -65 to 66
-
TABLE 01 MANUAL TRANSPORT - 67
-
TABLE 02 MATERIAL TESTING RATES - 68 to 69
BUILDING SCHEDULE OF RATES (BSR) – 2021
This Document is valid from 1st of January 2021 to 31st of December 2021
Prepared by Department of Engineering Services, Central Provincial Council
 Basic Prices
The basic prices approved by the Central Provincial Price Committee 2020 are used to
prepare the BSR for the year 2021.
 General Notes
 This BSR is prepared according to SRI LANKA STANDARD 573:1999

 This document is to be used for buildings within Central province.
 This document is to be used for estimation purpose only.
 The BSR is to be read in conjunction with the Standard Specification issued for
building work by the Institute of Construction Training and Development (ICTAD)
/ Construction Industry Development Authority (CIDA), except where superseded
by the notes or the descriptions in the schedule.
 Only those materials which are specially mentioned in the descriptions should be used
and should be the best quality material, confirming to the requirements of the relevant
standard. (SLS, ISO or BS)
 All the materials & the quality of the material should be approved by the Engineer,
described in the agreement.
I
Working Rates of this BSR are calculated as follows
a. For the projects where the Total Cost Estimate (TCE) is less than or equal 3 million
rupees
 Overheads & Profit margin is taken as 26 % of the basic rates.

Where,
Item No. Overhead Type Percentage
A Site Overhead 16
B Profit 10
C Total Overhead & Profit 26
Table-01
 Working Rates = Basic Rates + Overheads & Profit Margin.
b. For the projects where the Total Cost Estimate (TCE) is over 3 million rupees
 Separate preliminary bill shall be included.(Applicable site overhead percentages for

the preliminary bill shall be taken from Table – 03)
Where,
Item No. Overhead Type Percentage
A General Overhead 06
B Profit 10
C Total Overhead & Profit 16
Table-02
II
 Following are the breakup of overheads,
Item Site Overhead Percentage
No.
1 Supervision of work (wages of work supervisors) 1
2 Supervision of labor (wages of gangers) 4
3 Temporary work :
a) Access road & maintenance 0.2
b) Accommodation for labor 0.7
c) Stores building 0.6
d) Fencing, Hording & Protection 0.3
e) Provision of water, Lights etc 0.3
f) Clearing 0.2
g) Stacking of building materials including cement & steel 0.4
4 Security for construction sites 0.8

5 Tools and implements for miscellaneous work 0.9
6 Setting out according to the drawings 0.5
Providing samples for testing 0.2
7 Transportation of Supervisory staff 1.0
8 Job office, furniture, stationary, suppliers, water, lights etc. 0.9
9 Wages for job office staff 1.2
10 Transportation for job office staff 0.4
11 Bonds for bid performance and Fidelity Guarantee 0.3
Providing Insurance of work and workman’s compensation 0.5
12 Interest for Capital investment 1.6
Total 16
Table-03
 Note: The contractor shall submit “As Built Drawings” with the final valuation (Bill), if
stated in the contract documents
III
Table-04
Item General Overhead Percentage
No.
13 Head office and rent, lights, telephone, stationary, suppliers, 0.6

furniture etc. for same.
14 Salaries of Head office manager, engineers, technical assistants, 1.2
Draught men, Clerks, Stenos, Typists, minor staff and drivers
15 Transportation and subsistence for head office staff 1.0
16 Insurance, interest, and taxes on business 0.4
17 Legal expenses and consultancy fees 0.2
18 Workshop and yard rents, sheds, garages and supplies 2.2
19 Salaries of workshop and yard storekeepers, drivers, foremen, 0.4
mechanics and workmen.
Total 6.0
IV
c. Following are the breakup of overheads for improvements and maintenance projects where
the total cost estimate (TCE) over 3 million rupees.
 Separate preliminary bill shall be included.(Applicable site overhead percentages for the
preliminary bill shall be taken from Table – 05)

No.
1 Supervision of work (wages of work supervisors) 0.8
2 Supervision of labor (wages of gangers) 2
3 Temporary work :
a) Access road & maintenance 0.2
b) Accommodation for labor 0.4
c) Stores building 0.3
d) Fencing, Hording & Protection 0.3
e) Provision of water, Lights etc 0.2
f) Clearing 0.2
g) Stacking of building materials including cement & steel 0.2
4 Security for construction sites 0.5

5 Tools and implements for miscellaneous work 0.5
6 Setting out according to the drawings 0.4
Providing samples for testing 0.2
7 Transportation of Supervisory staff 0.3
8 Job office, furniture, stationary, suppliers, water, lights etc. 0.3
9 Wages for job office staff 0.6
10 Transportation for job office staff 0.3
11 Bonds for bid performance and Fidelity Guarantee 0.3
Providing Insurance of work and workman’s compensation 0.4
12 Interest for Capital investment 1.6
Total 10
Table-05
V
 Measurements of painting (Doors, Windows & Partitions)
Measurement of painting when both sides are painted shall be calculated by multiplying the area of
one side of the door, window or partition painted by the coefficients as below.
 Doors, windows or partitions fully glazed 1.25

 Doors, windows Glazed and panelled 1.75
 Doors, windows fully panelled 2.25
 Doors, windows Battened, ledged & braced 2.25
 Doors, windows with wooden louvers 3.00
 Allowances to be made in the rates for the works in upper floors

The rates included in this BSR are prepared only for the ground floor items. To obtain the rates for
the other floors, the ground floor rates should be multiplied by the following factors.
Ground to 1st Ground to Ground to

floor 2nd floor 3rd floor
Form work (sqr) 2% 4% 6%
Concrete (cube) 3% 5% 7%
9" Brick work (sqr) 5% 7% 9%
9" brick work (cube) / R.R.
5% 7% 10%
Masonry
4½" brick work (sqr) 5% 7% 10%
Steel reinforcement (cwt) 2.5% 5% 8%
Plastering (sqr) 5% 10% 15%
External Painting (sqr) 3% 6% 9%
Floor tiling (sqr) 2% 4% 6%
Wall tiling (sqr) 2% 4% 6%
Roof Calicut tiles (sqr) 3% 6% 9%
Roof asbestos (sqr) 3% 5% 7%
Ceiling work 3% 5% 7%
Table-06
These rates are limited only for four storied building.
VI
 Imported Materials
When imported materials are allowed to be used, it should be approved by the Engineer described in
the contract agreement.
 Aluminium works
a. All aluminium metal work shall comply with specification AA6063, T5 or BS 1474 of 1972.
Special attention should be drawn to the following details.
 Alloy – AA6063
 Hardness – 71 – 81 Rockwell E
 Temper – T5
 Tensile strength – 155 N/sq.mm (minimum)
 Anodizing Thickness– 10-15 Micron and should be confirmed to BS 3987 - 1974
 Powder Coating Thickness– 60-80 micron and should be confirmed to BS 6496: 1984
 Sample should be approved by Engineer / Architect
 Thickness of extrusions for windows & partition – 1.2 mm + 10%
 Thickness of extrusion for door – 1.5 mm + 10 % door
Size of extrusion in member of Doors, Windows and Partitions.

 visible finish size of sash to be minimum 65 mm
 Width of frame members in doors – 100 mm
 Width of frame members in sliding doors – 70 mm
 Width of frame in casements window – 60 mm
 Width of partition & shop front – 76 mm
b. The colour anodized finish shall be a coating of non fading and hard organic type in dark Bronze
colour (Lower limit) compatible with the colour used.
c. All extruded aluminium alloy sections shall be bronze anodized to a thickness 15–20 microns.
The bidder should furnish a manufacturer’s certificate that the anodized finish complies with the
specified micron content.
d. Screws used in the construction of frames shall be high tensile stainless steel or a non-corrosive
material compatible with aluminium.
VII
 Waterproofing
For waterproofing, cementitious, elastomeric or bituminous materials shall be used, according
to the situation. This should be approved by the Engineer described in the contract agreement.
 For electrical cable sections given in BSR the following table should be followed
New
Conductor cross section Old method
method
mm2 a/dia. (inch)
a/dia. (mm)
mm2
1.0 1/1.13 1/0.044
1.5 1/1.38 1/0.054
1.5 7/0.53 3/0.029
2.5 7/0.67 7/0.029
4.0 7/0.85 7/0.036
6.0 7/1.04 7/0.044
10 7/1.35 7/0.052
16 7/1.70 7/0.064
25 7/1.35 19/0.052
30 19/1.53 19/0.064
Table-07
a = Number of strands
dia. = Diameter of a conductor
Cable colour Code

Old Colour New colour code
Code
Single phase Three phase Single phase Three phase
L – Red L1 -Red L – Brown L1 - Brown
N - Black L2 –Yellow N - Blue L2 - Black
E – Green & yellow L3 - Blue E – Green & yellow L3 - Ash
N - Black N - Blue
E – Green & yellow E – Green & yellow
Table-08
VIII
 Method of Measurement
Bill of Quantities have been generally prepared in accordance with principles of the Standard
Method of Measurements for Building work in Sri Lanka (SLS 573 1999 )
 The quantities of material, plant and labor required for the items are computed from known data
and experience.
 Rates of each item include 10km distance for transport of sand, metal, steel, bricks when transport
distance exceeds 10 km additional cost should be added according to Material price and Transport
cost 2020.
 Head transport rates refer Material price and Transport cost 2021. Necessity of head transport
should be decided by Engineer.
 New rates shall be prepared for any item deviate from the description of the BSR.
 All unit rates are in Sri Lankan Rupees.
 SI – British conversion factors

Mass 1kg 2.204 lb
Length 1m 3.281 ft
Volume 1m3 35.315 ft3
1 Cuft 0.028 m3
1 Sqrs 9.290 m2
1 cu 2.831 m3
1 sqft 0.092 m2
1 lb 0.453 kg
1 c.w.t. 50.802 kg
1 gal 4.546 l
Table-09
IX
 Timber
Under exceptional Circumstances, any equivalent timber to the given species may be
used with the approval of the Engineer.
Structural timber for Roof work, ceiling frames and Partitions

Local timber: Palu, Wewarana, Liyan, Alubo, Pihimbiya, Valdel , Mee, Milla, Halmilla,
Kohomba, Micro, Kolon, Madan, Hulanhik., Treated Grandis
Imported timber: Balau, Kempas, Tulang
Valance board
Local timber: Ginisapu, Gammalu, Suriyamara, Hulanhik. Kolon
Imported timber: Tulang
Floor Boarding Teak, Kumbuk

Door, Window and Fanlight
For Frame:
Local timber: Palu, Wewarana, Valdel , Mee, Milla, Halmilla, Hadawaka, Kohomba,
Hulanhik.
Imported timber: Balau, Thulang
For sashes:
Local timber: Halmilla , Hulanhik, Sooriya mara, Kohomba
Imported timber: Thulang
Beadings Lunumidella, Mahogany
X
State Timber Corporation
Timber Classifications
Extracted from http://www.timco.lk/stc/files/CLASSIFICATIONofTIMBER.pdf
on 28/12/2020
CLASSIFICATION OF TIMBER
(Logs & Sawn Timber)
Super Luxury Class :

Teak, Ebony, Nedun, Calamander
Luxury Class :
Satin, Halmilla, Milla, Mahogany (Narrow leaved), Mahogany (Broad leaved), Jak
Special Class Upper :

Gammalu, Hulanhik, Margosa, Suriyamara, Rannai, Wewarana, Kolon, Velang, Palu
Special Class :
Tamarind (Hard Wood), Kumbuk, Eucalyptus microcorys
Class I :
Tawwanna, Uva Mandora, Munamal, Ubberiya, Eucalypus Pilularis, Eucalyptus Citriodora, Accasia
Melanoxylon, Panakka, Hora, Kirihambiliya, Urukanu or Uruhonda, Mandora, Pihimbiya, Etathimbiriya
or Ginikulu, Helamba, Del, Liyan, Neralu, Madan, Kon, Kirikon, Wanami, Mi, Na (Mesua ferrea),
Ketakela, Pathkela & Keeriya, Trestania comserta, Paramara, Hedawaka, Treated Grandis, Damba,
Dambu, Domba.
Class II :
All Dun species other than Thiniyadun, All Keena species other than Walukeena, Alubo, Dawata, Dawul –
Kurundu, Godapara, Halmandora, Panamora, Wa, Welipenna, Toona, Mihiriya, Karaw, Panu-Dan,
Rathatiya, Thimbiri, Derana, Na Imbul, Gonapana, Thiththeta, Kosganna, Kiripedda, Talang, Euclyptus
Grandis, Cypress, Ethdemata, Ginisapu, Ehela, Boron Treated Sawn Rubberwood, Alastoniya (Havari
Nuga), Boron Treated Sawn Pinus, Eucalyptus Robusta (Red Gum), Eucalyptus Globulus (Blue Gum),
Comporta, Redness, Coconut, Eucalyptus Thoraliyana, Eucalyptus Kamaldensis, Kaya, Eucalyptus
Tereticornis, Accacia docaran, Accacia mangium, Lunumidella.
Class III :
Aridda, Malabada, Diyathaliya, Pinus,Thelambu, Bath-hik, Atamba, Bulu, Kahata, Rubber, Rata-
Amba(Mango), Ratadel, Davu, Godakaduru,Gokatu, Sabbukku (Graviliya), Godakirilla, Mora,Kataboda,
Goraka, Tammarin (Sapwood), Bakme, Kakuna, Casurina (Kasa Kasa), Beli, Dunumandala, Batadomba.
Class III Others :
All species not otherwise classified.
General Manager
State Timber Corporation
2019.12.03
XI
 Cement Blocks
Test report shall be submitted by the contractor on compressive strength for every 500 number of
cement blocks supplied to the site. When the number of blocks involved for the project is less than
500, the necessity of the test shall be decided by the engineer.
 Interlock Blocks
Test report shall be submitted by the contractor on compressive strength for every 800 number of
interlock blocks supplied to the site. When the number of blocks involved for the project is less than
800, the necessity of the test shall be decided by the engineer.
 Fence Posts
Test report shall be submitted by the contractor on compressive strength of concrete (Rebound
Hammer Test) for every 15 number fence posts
XII
BUILDING SCHEDULE OF RATES
EFFECTIVE FROM 2021 JANUARY
RATE FOR
RATE FOR
SE. ITEM TCE
DESCRIPTION UNIT TCE ABOVE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION C - DEMOLITION /
ALTERATION / REPAIR AND
MAINTENANCE
DEMOLITIONS
Hacking up pavings
Demolishing Hacking up & clearing debris away of
1 C-001 floor paving brick or rubble inclusive of rendering. m2 173.00 188.00
Demolishing Hacking up & clearing debris away of

2 C-002 m2 231.00 251.00
floor concrete inclusive of rendering.
Brick work and Masonry
Demolishing bricks walls 112.5mm thick inclusive of
3 C-003 plaster and any fixtures including debris cleared away. m2 462.00 502.00
Demolishing bricks walls above 225mm thick inclusive

4 C-004 of plaster and any fixtures including debris cleared m2 427.00 464.00
away.
Demolishing and clearing debris of 225mm wide drain
5 C-005 m 229.00 249.00
in brick masonry.
Demolishing rubble masonry in cement and sand
6 C-006 inclusive of plaster and any fixtures, rubble stacked and m3 2,363.00 2,567.00
removing debris .
Flooring and Ceiling
7 C-007 Demolishing & clearing tiled, glazed floor or wall. m2 460.00 500.00
Removing asbestos ceiling including timber framework,
8 C-008 stacking serviceable materials and debris cleared away. m2 302.00 328.00
in single storied building.
Removing asbestos ceiling including timber frame
9 C-009 work, stacking serviceable materials and debris cleared m2 261.00 283.00
away in two storied building.
Roofs
Removing & clearing debries away Corrugated sheets,
10 C-010 iron, asbestos or aluminium alloy from roof excluding m2 65.00 71.00
frame work in single storied buildings.
iron, asbestos or aluminium alloy from roof including
11 C-011 frame work inclusive of wiring and fixtures, gutters, m2 196.00 213.00
valance boards etc.. in single storied buildings.

valance boards etc.. in two storied buildings.
Provincial Price Committee 2021 Page 1

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
frame work . in two storied buildings.
valance boards etc.. in three storied buildings.

frame work . in three storied buildings.
Removing & clearing debries away tiles calicut or half
round, removed from roof of single storied buildings
16 C-016 m2 115.00 125.00
excluding framework including stacking serviceable
materials and debris cleared away.
Removing & clearing debries away tiled roof with
frame work inclusive of wiring and fixtures, gutters,
17 C-017 valance boards etc., stacking serviceable materials and m2 311.00 338.00
debris cleared away in single storied buildings.

round, removed from roof of two storied buildings
18 C-018 m2 173.00 188.00
excluding framework including stacking serviceable
materials and debris cleared away.
19 C-019 valance boards etc., stacking serviceable materials and m2 427.00 464.00
debris cleared away in two storied buildings.

round, removed from roof of three storied buildings and
20 C-020 above excuding frame work, including stacking m2 231.00 251.00
serviceable materials and debris cleared away.

21 C-021 m2 543.00 590.00
valance boards etc., stacking serviceable materials and
debris cleared away in three storied buildings.
22 C-022 Removing & stacking Ridges, asbestos or tile. m 84.00 91.00
Removing & stacking Gutters, down pipes, valleys GI or
23 C-023 m 58.00 63.00
PVC including specials .
24 C-024 Removing & stacking Boards, valance and barge. m 44.00 47.00
Truss
Removing and stacking trusses steel or timber 6.1m (20
25 C-025 nr 4,405.00 4,785.00
L.ft) of span from single storied building.
26 C-026 nr 5,507.00 5,981.00
27 C-027 nr 6,608.00 7,178.00
Walls

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Demolishing reinforced concrete walls, beams or slabs
28 C-028 m3 15,178.00 16,487.00
up to first floor and debris cleared away.
29 C-029 m3 15,956.00 17,332.00
up to second floor and debris cleared away.
30 C-030 m3 17,124.00 18,600.00
up to third floor and debris cleared away.
Doors & Windows
Removing & stacking door or window (sash with frame)
31 C-031 nr 2,883.00 3,131.00
size up to 4.0m2 from existing walls.
Removing & stacking Door or window (sash with
32 C-032 nr 2,883.00 3,131.00
frame) size over 4.0m2 from existing walls.
Removing & stacking Door or window sash size up to
33 C-033 m2 275.00 298.00
4.0m2 from existing frames.
Removing & stacking Door or window sash only size
34 C-034 m2 412.00 448.00
over 4.0m2 from existing frame.
Sanitary fittings
Removing ang staking Low-level suits, squatting closets.
35 C-035 nr 856.00 929.00
Removing & stacking Wash basins, cisterns, sinks,
36 C-036 nr 535.00 581.00
urinals.
37 C-037 Removing & stacking Pipes PVC, GI. m 28.00 30.00
ALTERATIONS
Supplying & fixing approved closet squatting foot rest
type (Orissa pan) with trap, supplied and fixed to
38 C-038 working order, including connection to sewer line. Rate nr 18,365.00 19,948.00
includes for breaking floor and concreting, cement
rendering in damaged areas.
39 C-039 Removing and re-fixing available wash basin. nr 3,619.00 3,931.00
Removing finishings
40 C-040 Paint removing from any surfaces with blow lamp. m2 345.00 375.00
Chipping & clearing debris away from brick wall
41 C-041 m2 259.00 281.00
plasters and floor rendering.
Chipping & clearing debris away from concrete wall
42 C-042 m2 388.00 422.00
plasters and concrete floor rendering.
Cement, lime and sand plaster, breaking the damaged
areas and replastering with 20mm thick 1:1:5 cement,
43 C-043 m2 1,383.00 1,503.00
lime and sand, finished smooth with lime putty.
Cement and sand rough plaster, breaking the damaged

areas and replastering with 1:1:5 cement, lime and sand
44 C-044 m2 1,158.00 1,258.00
plaster, finished semi-rough with wooden float.
Floor re-rendering with 1:3 cement and sand after

demolishing and clearing damaged areas, providing
45 C-045 m2 1,238.00 1,344.00
expansion joints filled in 1:2 bitumen and sand (Rate
including for curing).
Removing coverings

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Removing & stacking partitions, weld mesh, shelves
46 C-046 m2 251.00 273.00
from existing walls.
Uprooting & stacking all materials barbed wire upto 5
47 C-047 strands fence (Barbed wire tobe rolled up,Length of the m 333.00 362.00
fence to be measured).
Refixing available RCC fence posts , Rate includes for
48 C-048 nr 823.00 894.00
concreting 1:3:6(40mm) where necessary.
Strengthing & fixing available barbed wire 14 gauge 4
49 C-049 points, on exiting concrete or timber fence posts. m 31.00 34.00
Suppling & fixing barbed wire 14 gauge 4 Points,on

50 C-049B existing concrete or timber fence posts. m 49.00 54.00
REPAIRS AND MAINTENANCE
Brick work/ Masonry with available material

Brick work in 1:5 cement sand mortar 112.5mm thick
51 C-050 m2 1,479.00 1,606.00
(Nominal) using available bricks.
Brick work in 1:8 cement & sand mortar 225mm thick
52 C-051 m3 9,268.00 10,067.00
(Nominal) or above. (using available bricks)
R.R masonry in 1:5 cement and sand motar in
53 C-052 m3 13,789.00 14,978.00
foundations using available rubble.
Repointing
Replacing glass panes plain / pinhead 3mm in complete.
54 C-053 m2 2,834.00 3,079.00
Replacing glass panes plain / pinhead 4.6mm in
55 C-054 m2 3,389.00 3,682.00
complete.
Fabricating and fixing Security weld mesh in open type
buildings in GI weld mesh 50mm x 50mm SWG 10,
welded on 40mm x 40mm x 5mm MS angle frame
56 C-055 complete with application of two coats enamel paint m2 4,857.00 5,275.00
over two coats of anticorrosive paint (using available
weld mesh ).
Fabricating and fixing security weld mesh on existing
window frames complete with class 1 timber beadings,
57 C-056 and applying two coats paint to match the exiting m2 2,236.00 2,429.00
including two coats of enamel paint & primer under
coat.
Laying calicut tiles (available) on roof (For scattered
58 C-057 nr 10.00 11.00
laying) up to 10 tiles per building only.
Supplying and laying of new calicut tiles ( scattered
59 C-058 laying where necessary) up to 25 tiles per building only. nr 98.00 107.00
Shifting and re-laying after cleaning calicut tiles. (For

60 C-059 measurements of area not exceeding 25 tiles). nr 41.00 45.00
Replacing Asbestos roofing sheets with new sheets on

existing frame work.with new nut and bolts, apply two
61 C-060 m2 1,998.00 2,170.00
coats of emulsion paint under side of sheet etc.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Old ceilings and beams
Cleaning and placing available roof trusses in position
62 C-061 with supplying necessary bolts and templates, 6m (20 nr 14,007.00 15,214.00
L.ft) to 7.2m (24 L.ft) spans.
63 C-062 with supplying necessary bolts and templates, 7.6m (25 nr 16,199.00 17,595.00
L.ft) to 8.7m (29 L.ft) span.
with supplying necessary bolts and templates, 9.1m
64 C-063 nr 18,391.00 19,977.00
(35L.ft)and above up to 12.2m (40 L.ft) span.
Fixing available steel purlins on roof structures

65 C-064 complete with necessary bolts, welding, cleaning and m 348.00 378.00
painting two coats anticorrosive paints etc.
Reparing Timber
Replacing with new class 1 timber 50mm x 25mm
(nominal) for reepers including application of two coats
66 C-065 m 171.00 186.00
of wood preservative(stain) (Only up to 4.60m2 of
roof area).
Replacing with new kempus timber 50mm x 25mm
(nominal) for reepers including application of two
67 C-066 m 245.00 266.00
coats wood preservative(stain) ( Only up to 4.60m2 of
roof area).
(nominal) for battens including application of two
68 C-067 m 413.00 449.00
coats of wood preservative(stain) (Only up to 4.6m2
of roof area).
(nominal) for battons including application of two
69 C-068 m 439.00 477.00
coats wood preservative(stain) ( Only up to 4.6m2 of
roof area)
(nominal) for joists/ rafters, including application of two
70 C-069 m 1,307.00 1,420.00
coats of wood preservative (stain) ( only up to 4.6m2 of
roof area).
(nominal) for joists/ rafters including application of two
71 C-070 m 1,341.00 1,457.00
coats wood preservative (stain) ( only up to 4.6m2 of
roof area)
Cleaning and fixing timber (available), on roof, size
72 C-071 m 65.00 71.00
50mm x 25mm.
73 C-072 m 71.00 77.00
50mm x 50mm.
74 C-073 m 317.00 345.00
100mm x 50mm.
75 C-074 m 317.00 345.00
100mm x 75mm.
76 C-075 m 317.00 345.00
125mm x 50mm.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Repairing and re-fixing of door and window frames
77 C-076 nr 498.00 541.00
,timber if used measured separately.
Repairing and re-fixing of door or window sash (timber,
78 C-077 except beadings if used measured separately). m2 2,684.00 2,915.00
Repairing door & window frames using treated kempas,

79 C-078 m 1,502.00 1,631.00
95mm x 45mm (Nominal).
Repairing door & window frames using treated kempas,
80 C-079 m 2,038.00 2,213.00
Repairing door & window frames using Jack timber
81 C-080 m 1,792.00 1,947.00
Repairing door & window frames using Jack timber
82 C-081 m 2,420.00 2,628.00
Repairing door sash using class 1 or above timber up to
83 C-082 nr 7,339.00 7,971.00
28mm thick planks. ( Up to 2.0m2)
Repairing door sash using special class or above timber
84 C-083 nr 8,803.00 9,562.00
up to 28mm thick planks. ( Up to 2.0m2)
Repairing glazed / panelled window sash using class 1
85 C-084 or above timber up to 28mm thick planks. ( Up to nr 4,308.00 4,680.00
1.2m2)
Repairing glazed / panelled window sash using special
86 C-085 class or abovetimber up to 28mm thick planks. ( Up to nr 5,040.00 5,475.00
1.2m2)

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION D - EXCAVATION AND
EARTH WORK
Site preparation
87 D-001 Clearing jungle along the fence. m2 69.00 74.00
Cutting coconut trees removing root balls and stacking
88 D-002 nr 7,252.00 7,878.00
logs.
89 D-003 Cutting coconut trees and removing stumps. nr 5,112.00 5,553.00
Cutting trees girth 0.5m to 1.0m, removing root balls
90 D-004 nr 11,589.00 12,588.00
and stacking logs.
91 D-005 Cutting trees girth 0.5m to 1.0m and stacking logs. nr 7,288.00 7,916.00
92 D-006 nr 16,727.00 18,169.00
and stacking logs.
94 D-008 nr 24,015.00 26,085.00
and stacking logs.
96 D-010 nr 40,742.00 44,254.00
and stacking logs.
98 D-012 nr 48,030.00 52,171.00
and stacking logs.
Excavation
Earth excavation in top soil for preservation, average
100 D-014 m2 313.00 340.00
depth 200 mm and stock piling within 30m
Earth excavation in leveling site inclusive of haulage up
101 D-015 to 30m. (manual cutting only up to 450m3) Average m2 356.00 387.00
depth <= 300mm
102 D-016 to 30m. (manual cutting only up to 450m3) Average m3 1,567.00 1,702.00
depth > 300mm
103 D-017 to 30m. (machine cutting only) in ordinary soil. m3 205.00 223.00
Excavation and levelling site in soft rock involving

104 D-018 m3 2,323.00 2,524.00
manual digging inclusive of haulage up to 30 m.
Excavation in foundations in normal earth up to depth of
105 D-019 1.0 m inclusive of backfilling, compacting and disposal m3 1,567.00 1,702.00
of surplus earth.
Excavation in foundations in normal earth, depth greater
than 1.0 m and up to 2.0m inclusive of backfilling,
106 D-020 m3 1,715.00 1,863.00
compacting and disposal of surplus earth.
Excavation in foundations in normal earth, depth greater

107 D-021 than 2.0 m inclusive of backfilling, compacting and m3 2,323.00 2,524.00
disposal of surplus earth.
Excavation in foundations in soft rock requiring manual
108 D-022 digging, up to a depth of 1.0m inclusive of backfilling m3 1,973.00 2,143.00
and disposal of surplus materials.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
digging, depth greater than 1.0m and up to 2.0m
109 D-023 m3 2,351.00 2,554.00
inclusive of backfilling and disposal of surplus
materials.
110 D-024 digging, depth greater than 2.0m inclusive of backfilling m3 3,107.00 3,375.00
and disposal of surplus materials.
Excavation in wells / pits in normal earth up to depth of
1.0m inclusive of backfilling behind wall / ring and
111 D-025 m3 1,567.00 1,702.00
disposal of surplus earth, rate excluding for shoring.
Excavation in wells / pits in normal earth 1.0m to 2.0m

depth inclusive of backfilling behind wall /ring and
112 D-026 m3 1,945.00 2,113.00
Excavation in wells / pits in normal earth 2.0m to 3.0 m

113 D-027 m3 2,702.00 2,934.00
Excavation in wells / pits in normal earth 3.0m to 4.0m

114 D-028 m3 3,864.00 4,197.00
Breaking out existing material

Rock Requiring blasting & pilling inclusive of haulage
up to 30 m. Payable on rubble measurement only.
115 D-029 m3 5,039.00 5,473.00
(Rubble volume measured as - Pilling measurement X
0.75)
Rock Requaring blasting and remove the blasted rock
116 D-030 m3 4,301.00 4,672.00
from the site (within 10km)
Rock excavation in column footings or wall foundations.
117 D-031 m3 6,657.00 7,230.00
Earth work Support

Shoring for excavations (Trenches / Footings etc.) up to
118 D-032 m2 944.00 1,025.00
1.5m height.
Shoring for excavations up to 3m height.All as per detail
119 D-033 drawing No .CPC/CS/11/04/2017/Type-ST/03 m2 11,066.00 12,020.00
Disposal
Bailing out and cleaning of well total depth up to 3.0m
120 D-034 (measured, capacity of well below water table). m3 690.00 750.00
Bailing out and cleaning of well total depth up to 4.8m

121 D-035 (measured, capacity of well below water table). m3 1,380.00 1,500.00
Bailing out and cleaning of welltotal depth up to 7.5m

122 D-036 (measured, capacity of well below water table). m3 1,933.00 2,100.00

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Extra over excavation for removing boulders size
exceeding 0.05m3,in any manner (Volume of each
123 D-037 m3 3,689.00 4,007.00
boulder measured as 0.75 x Average height x Squared
area).
Depositing and spreading haulage of earth more than
124 D-038 m3 409.00 445.00
30m away from site by any means.
Levelling ground to required grading cutting lumps and
125 D-039 m2 46.00 50.00
spreading and compacting manually.
Disposal of surplus earth, inclusive of loading and
126 D-040 unloading and transport up to 10 km.(Using Mechine) m3 402.00 436.00
Filling
Filling earth and compacting (as approved by Engineer)
127 D-041 150mm layers in large quantities. Rate includes for m3 1,782.00 1,935.00
transport of 30 m.
Filling earth and compacting (as approved by Engineer)
128 D-042 150mm layers under floors. Rate includes for transport m3 1,998.00 2,171.00
of 30 m.
Compacting approved gravel, filled in 150mm layers by
129 D-043 manual tamping as specified. (Gravel available at site) m3 1,142.00 1,241.00
Suplying and spreading river sand in layers as specified

130 D-044 under foundations, drainage sand blankets, filters, m3 6,084.00 6,608.00
around soakage pits, wells etc.
Compacting approved gravel in 150mm layers by any
131 D-045 means except manual tamping as specified. (Gravel m3 562.00 611.00
available at site)
132 D-046 Sand filling under foundations. (As a cushion) m3 6,376.00 6,925.00

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION F - CONCRETE WORKS
Insitu concrete
Mixing and placing in position concrete grade 30,
nominal mix 1:1:2 (20mm) using a concrete mixer
133 F-001 m3 29,124.00 31,635.00
including fuel / operator / handling/vibrator & curing.

nominal mix 1:11/2:3 ( 20mm) using a concrete mixer
134 F-002 m3 24,872.00 27,016.00

nominal mix 1:2:4 ( 20mm) using a concrete mixer
135 F-003 m3 23,433.00 25,453.00
Mixing and placing in position concrete

136 F-004 1:21/2:5(25mm) using a concrete mixer including fuel / m3 18,064.00 19,621.00
operator / handling/vibrator & curing.
Mixing and placing in position concrete 1:3:6 (40mm)
137 F-005 using a concrete mixer including fuel / operator / m3 17,524.00 19,034.00
handling & curing.
138 F-006 nominal mix 1:2:4 ( 20mm) manualy including m3 27,086.00 21,022.00
compacting and curing.
Mixing and placing in position concrete
139 F-007 1:21/2:5(25mm) manualy including compacting and m3 21,717.00 23,589.00
curing.
Mixing and placing in position concrete 1:3:6 (40mm)
140 F-008 m3 21,176.00 23,002.00
manualy including compacting and curing.
Rate of placing, porker vibrating, leveling and curing of
141 F-009 Ready mixed concrete of any grade. (Cost of Ready m3 912.00 991.00
mix concrete is not included.)
Form Work
Sawn timber formwork in class III timber for ground
concrete work with side support or props, at ground
142 F-010 m2 1,461.00 1,587.00
level plinth beams, lintols etc. including fixing and
dismantling.
Sawn timber form work in class III timber with bearers,
143 F-011 joist and props including fixing and dismantling for m2 1,591.00 1,728.00
underside of first floor slab.
Sawn timber formwork in class III timber with side
144 F-012 support using props for columns mould including m2 2,887.00 3,136.00
fixing, and dismantling in ground floor.
underside of first floor beams.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
portal frames.
Reinforcement
Mild steel reinforcement bend to shape laid in position
147 F-015 and tied with G.I. wire as directed.Including spaces & Kg 307.00 334.00
chairs.
Tor steel reinforcement bend to shape laid in position
148 F-016 and tied with G.I. wire as directed.Including spaces & Kg 307.00 334.00
chairs.
Flag Post
2400mm x 825mm x 450mm plat form with 75mm thick
1:3:6 (40mm) base & 2400mm x 300mm x 225mm step
in rubble and 75mm thick 1:2 :4 (20mm) concrete
topping. Inclusive of 1:3 cement and sand rendering
finished smooth with coloured cement floating and
149 F-017 polishing and providing three numbers No 66,262.00 71,974.00
2"dia.(O.D.),4.5mm tk. G.I.pipe flag post complete with
painting (two coats of metal primer and two coats of
enamal) and provide necessary arrangements for
hoisting the flag as per the drawing
No.CPC/CS/11/04/2017/Type-ST/02(i).
3300mm x 1350mm x 600mm platform for Flag Post
with 1:2:4 (20mm) concrete and 1:3 cement and sand
rendering finished smooth with coloured cement floating
and polishing and providing three numbers 2" dia.
(O.D.) (4.5mm tk) G.I.pipe flag post complete with
150 F-018 painting (two coats of metal primer and two coats of No 146,090.00 158,684.00
enamal) and provide necessary arrangements for
hoisting the flag. All shall be to working order as per the
drawing Nos..CPC/CS/11/04/2017/Type-ST/02(i).
CPC/CS/11/04/2017/Type-ST/02(ii).
Concrete catch pits / valve chambers

Concrete catch pits / valve chambers in 50mm thick
1:2:4(20mm) concrete side walls and internal faces
cement rendered with 1:3 cement and sand finished
smooth, to be water tight, inclusive of provision for
151 F-019 necessary pipe connection etc, with suitable cover or No 1,027.00 1,115.00
grating on top to be flush with floor level. Internal
dimensions 150mm x 150mm x 300mm.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
smooth, to be water tite, inclusive of provision for
grating on top to be flush with floor level. Internal

smooth, to be water tite, inclusive of provision for
grating on top to be flushed with floor level. Internal
Extra over concrete chamber for earth electrode in

50mm thick 1:2:4(20mm) concrete side walls with
154 F-022 No 1,360.00 1,477.00
R.C.C cover slab on top. internal dimensions 150mm x
150mm x 300mm.
Drain
Drain 225mm X 150mm (average depth) concrete
1:21/2:5 (25mm) 75mm thick, provide expansion joints
at 3000mm crs 12mm thick , 1:3 cement, sand rendering
155 F-023 finished smooth, including necessary excavation, form m 2,457.00 2,673.00
work, laying polythene membrane under concrete and
laid to required slope.
Drain 225mm X 300mm(average depth) concrete 1:2
1/2:5 (25mm) 75mm thick, provide expansion joints at
3000mm crs 12.5mm thick , 1:3 cement, sand rendering
Drain 225mm x 450mm(average depth) concrete 1:2
1/2:5 (25mm) 75mm thick, provide expansion joints at
3000mm crs 12.5mm thick , 1:3 cement, sand rendering
750mm wide ramp and 225mm X 150mm(average
depth) drain in 1:2 1/2:5(25mm) concrete 75mm thick
with 1:3 plaster finished smooth, including necessary
158 F-026 excavation, form work, providing expansion joints at m 4,320.00 4,683.00
3000mm crs and laying polythene membrane under
concrete and laid to required slope.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Concrete cover slabs 50mm thick 1:2:4 (20 mm) r/f
with, 6mm dia. MS bars at bottom @ 100mm centre.
both ways, 1:3 cement and sand rendering finished
159 F-027 smooth, pre-cast in, pieces not exceeding 600mm x m2 4,821.00 5,237.00
450mm placed in position as directed, providing drain
holes if required.
Flight of Steps
Constructing flight of steps in 1:2 1/2 :5(25mm)
concrete overall width 1.5m, waist 100mm on well
compacted ground, waist below ground level, curb walls
150mm thick overall height 450mm in outer surface.
160 F-028 Rate includes all formwork and 1:3 cement rendering m 14,636.00 15,898.00
finished smooth to exposed surfaces. size of steps 150
mm rise and 275mm tread.(Measured sloping length.)
Constructing landing flight of steps 1.5m wide overall

base 100mm thick, curb walls 150mm thick and 150mm
161 F-029 height externally, in 1:2 1/2:5(25mm) concrete, and m 12,485.00 13,561.00
1:3.cement rendering finished smooth.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION G - MASONRY WORKS /

BRICK WORK / BLOCK WORK
WALLS
Brick work in 1:5 cement sand mortar 225mm thick
162 G-001 m3 21,348.00 23,188.00
(Nominal)and above in foundations up to D.P.C .
Brick work in 1:8 cement sand mortar 225mm thick
163 G-002 m3 21,598.00 23,460.00
(Nominal)in super structure in ground floor.
Brick work in 1:5 cement sand mortar 112.5mm thick
164 G-003 m2 2,713.00 2,947.00
(Nominal) in ground floor.
Brick work in 1:5 Cement Sand Mortar 225mm thick
165 G-004 m2 3,221.00 3,499.00
(nominal) Large brick in ground floor.
Brick work in 1:5 Cement Sand Mortar 150mm thick
166 G-005 m2 2,118.00 2,301.00
(nominal) Large brick in ground floor.
Masonry block work 100mm thick (Nominal) in walls
in cement and sand 1:5 motar using hollow blocks made
167 G-006 of cement and sand to the proportion of 1:10, m2 1,824.00 1,982.00
confirming to compressive strength not less than
2N/mm2 in ground floor.
Masonry block work 150mm thick (Nominal) in walls
in cement and sand 1:5 motar using hollow blocks made
168 G-007 of cement and sand to the proportion of 1:10, m2 2,100.00 2,281.00
confirming to compressive strength not less than
2N/mm2 in ground floor.
Masonry block work 200mm thick (Nominal) in cement
and sand 1:5 motar using hollow blocks made of
169 G-008 cement and sand to a proportion of 1:10, confirming to m2 2,745.00 2,982.00
compressive strength not less than 2N/mm2 in ground
floor.
PROJECTION
170 G-009 m3 15,963.00 17,339.00
foundations.
171 G-010 m3 17,507.00 19,016.00
superstructure.
Providing of weep holes in retaining walls with 90mm
dia. PVC down pipes including metal packing around
172 G-011 nr 598.00 650.00
inner mouth as directed, length of pipe up to 1050mm.

173 G-012 nr 714.00 775.00
inner mouth as directed, length of pipe 1050mm to
1800mm.
174 G-013 nr 834.00 906.00
inner mouth as directed, length of pipe 1800mm to
2250mm.
Supplying and laying 1.5m x 1.0m x 1.0m galvanized
175 G-014 gabion boxes with necessary rubble packing. nr 14,379.00 15,618.00

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.

Supplying and laying geo textile layer behind gabion

178 G-017 m2 251.00 273.00
retaining walls type T.S. 30.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION H - WATER PROOFING
Supplying and laying of internal angle fillet

(25mmx25mm) at edges using non shrinkage grout and
179 H-001 fiber mesh (200mm width) after clearing at edges m 384.00 417.00
(preparing surface for waterproofing), as per the
instructions of the Engineer.
Waterproofing in upper floor bathrooms, water tanks
etc. with waterproofing agent approved by the Engineer,
180 H-002 m2 2,131.00 2,315.00
(Barralastic or equivalent) apply two coats after well
cleared surface.
Waterproofing with cementitious waterproofing agent
approved by the Engineer, (Xypex or equivalent) apply
181 H-003 m2 1,778.00 1,931.00
two coats after well cleareing and preparation of
surface.
Waterproofing with cementitious waterproofing agent

182 H-004 approved by the Engineer, (Thoroseal or equivalent) m2 1,285.00 1,396.00
apply two coats after well cleareing and preparation of
surface.Damp proofing, width > 300mm
20mm thick damp proof course in 1:2 cement and sand

183 H-005 m2 1,480.00 1,607.00
trowelled smooth and applied two coats of hot tar,
blinded with sand.Damp proofing, width > 300mm
Supplying and laying of water bar, including underlay
recessed to the early stage and new stage concrete with
184 H-006 m 1,190.48 1,293.10
surface treatments as per the instructions of the
Engineer.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION J - STRUCTURAL METAL

WORKS FOR STEEL IN FRAMED
STRUCTURES / ALUMINUM IN
FRAMED STRUCTURES / METAL
WORK IN UNFRAMED STRUCTURES
Supplying & Fixing Lipped Channel Size 100 mmx 50
185 J-001 mmx 12 mm & 2mm thick GI necessary nut & Bolts m 2,210.00 2,401.00
6mm thick cleat & Welding Works etc.
Supplying & Fixing Lipped Channel Size 150 mmx 65
mmx 14 mm & 2mm thick GI including prepare &
186 J-002 m 2,971.00 3,227.00
necessary nut & Bolts 6mm thick cleat & Welding
Works etc.
Fabricating and fixing Steel sections 2/ 62mm x 62mm x
6mm used in gable rafters purlins etc.complete with
187 J-003 fixing, bolts, 2 coats of anticorrosive paint and m 4,346.00 4,720.00
providing cleats where necessary . (Concrete pad paid
separately)
Suppling, fabricating and erecting Web truss 20-40 feet
span and pitch 10-45degree with Top and Bottom
Chord 2/60x60x5mm and Internal members single
angle 50x50x5mm, 10mm thick Guzzet plate, 12mm
thick base plate rate including welding and two coats of
188 J-004 anticorrosive paint and placing in position. Kg 408.00 443.00
CPC/CS/11/04/2018/TYPE-TR/01(i),(ii)
CPC/CS/11/04/2018/TYPE-TR/02(i),(ii)
CPC/CS/11/04/2018/TYPE-TR/03(i),(ii)
CPC/CS/11/04/2018/TYPE-TR/04(i),(ii)
CPC/CS/11/04/2018/TYPE-TR/05(i),(ii)
Fabricating and erecting "I" section truss 20-30 feet
span and pitch 10-45degree including two coats of
anticorrosive paint and placing in position. (Truss
Spacing 15'-0"-20'-0")Sag rod to be paid separately. As
189 J-005 per drawing No. CPC/CS/11/04/2018TYPE-ITR/02/1, Kg 369.00 401.00
CPC/CS/11/04/2018TYPE-ITR/02/2,
CPC/CS/11/04/2018TYPE-ITR/02/3

Spacing 15'-0"-20'-0")Sag rod to be paid separately. As
190 J-006 per drawing No. CPC/CS/11/04/2018TYPE-ITR/04/1, kg 311.00 338.00
CPC/CS/11/04/2018TYPE-ITR/04/2,
CPC/CS/11/04/2018TYPE-ITR/04/3

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
191 J-007 Spacing 15'-0"maximum) As per drawing No. kg 345.00 375.00
CPC/CS/11/04/2018TYPE-ITR/01/1,
CPC/CS/11/04/2018TYPE-ITR/01/2,
192 J-008 Spacing 15'-0"maximum) As per drawing No. kg 313.00 340.00
CPC/CS/11/04/2018TYPE-ITR/03/1,
CPC/CS/11/04/2018TYPE-ITR/03/2,

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION K - METAL WORK
Windows
Fabricating and fixing Anodized aluminium glazed
window with openable sash with aluminium
architectural sections with 10 - 15 micron coating glazed
193 K-001 4.6 mm thick glass including all necessary rubber m2 17,111.00 18,586.00
beading, rawl plug etc.(The used sections are CA 1009,
CA 1010, CA 2005, 70SM 1011)
Fabricating and fixing Anodized Aluminium glazed
fanlight with openable sash with aluminium architectural
sections with 10 - 15 micron coating glazed 4.6 mm
194 K-002 thick glass including all necessary rubber beading, rawl m2 22,722.00 24,680.00
plug etc.(The Used sections are -CA-1009, CA 1010,
CA 2005, 70SM 1011)
Fabricating and fixing Anodized aluminium sliding
window with aluminium architectural sections with 10 -
15 micron coating glazed with 4.6mm thick glass
195 K-003 including all necessary rubber beading, rawl plug m2 12,919.00 14,032.00
etc.(The used sections are 70S 1001, 70S 1101 -1, 70S
1201 - 1, 70S 1401, 70S 1501, 70S 1601, 70S 1701)
Fabricating and fixing Powder coated aluminium glazed

window with openable sash with aluminium
architectural sections with 60 - 80 micron coating with
196 K-004 4.6 mm thick glass including all necessary rubber m2 19,157.00 20,809.00
beading, rawl plug etc.(The used sections are CA 1009,
CA 1010, CA 2005,70SM 1011)
fanlight with openable sash with aluminium architectural
sections with 10 - 15 micron coating glazed 4.6 mm
197 K-005 thick glass including all necessary rubber beading, rawl m2 25,608.00 27,816.00
plug etc.(The Used sections are -CA-1009, CA 1010,
CA 2005, 70SM 1011)
sliding window with aluminium architectural sections
with 60 - 80 micron coating with 4.6mm thick glass
198 K-006 including all necessary rubber beading, rawl plug & m2 14,574.00 15,830.00
window lock etc.(The used sections are 70S 1001, 70S
1101 -1, 70S 1201 - 1, 70S 1401,70S 1501, 70S 1601,
70S 1701)
Louvers
Fabricating and fixing Anodized aluminium louvers
panel fixed to aluminium window or doors with
aluminium architectural sections with 10 - 15 micron
199 K-007 coating including all necessary fitting etc.(Aluminium m2 23,730.00 25,775.00
window or door measured separately).(The used
sections are DG01, DG101, A -110 -AT)

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Powder coated aluminium louvers panel fixed to
aluminiam windows or doors with aluminium
architectural section with 60-80 micron corting
200 K-008 including all necessary fitting etc.(aluminium window or m2 27,001.00 29,329.00
door measured seperatly.)(The used sections are DG 01,
DG 101, A110AT)
Doors and gates

Fabricating and fixing Anodized aluminium hinged type
door sash with aluminium architectural sections with 10 -
15 micron coating glazed and panelled with 3mm plastic
coated ply board to both sides at bottom and 4.6mm
201 K-009 thick glass at top.Including door lock and handle m2 24,853.00 26,996.00
etc.(The used sections are 100D 3105, 100D 103, 100D
101, 100D 201, 100D 301, 100D 401, 100D 501,
70SM 1011, BD -1068)
Fabricating and fixing Anodized Aluminium hinged type

door sash with aluminium architectural sections with 10 -
15 micron coating glazed and panelled with 4mm
cladding board at bottom and 4.6mm thick glass at
202 K-010 top.including door lock and handle etc.(The used m2 26,754.00 29,060.00
sections are -100D 3105, 100D 103, 100D 101, 100D
201, 100D301, 100D 401, 100D 501, 70SM 1011,
BD1068)
Fabricating and fixing Anodized Aluminium hinged type
sash door with aluminium architectural sections with 10 -
15 micron coating glazed and panelled with 4mm
203 K-011 cladding board .including door lock etc.(The used m2 27,147.00 29,487.00
201, 100D301, 100D 401, 100D 501, 70SM
1011,BD1068)
Fabricating and fixing Anodized aluminium glazed
sliding type door sash with aluminium architectural
sections with 10 - 15 micron coating glazed and
panelled with 3mm plastic coating ply board to both
204 K-012 sides,at bottom and 4.6mm thick glass at top ,including m2 11,200.00 12,166.00
door lock.(The used section 70S - 1002 -1, 70S 1102 -1,
70S 1701 A, 70S 1402-1, 70S - 1801, 70S 1501, 70S
1202 - 1)
Fabricating and fixing Powder coated aluminium hinged
type door sash with aluminium architectural sections
with 60 - 80 micron coating glazed and panelled with
3mm plastic coated ply board to both sides at bottom
205 K-013 and 4.6mm thick glass at top.Including door lock m2 27,176.00 29,519.00
etc.(The used sections are 100D 3105, 100D 103, 100D
101,100D 201, 100D 301, 100D 401, 100D 501,70SM
1011)

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
type sash door with aluminium architectural sections
with 60-80 micron coating glazed and panelled with
206 K-014 4mm cladding board including door lock etc.(The used m2 29,469.00 32,010.00
201, 100D301, 100D 401, 100D 501, 70SM 1011)

type sash door with aluminium architectural sections
with 60-80 micron coating glazed and panelled with
4mm cladding board at bottom and 4.6mm thick glass at
207 K-015 top.including door lock etc.(The used sections are - m2 29,076.00 31,583.00
100D 3105, 100D 103, 100D 101, 100D 201, 100D301,
100D 401, 100D 501, 70SM 1011)

sliding type door sash with aluminium architectural
panelled with 3mm plastic coating ply board to both
208 K-016 sides,at bottom and 4.6mm thick glass at top, including m2 12,199.00 13,251.00
door lock.(The used section 70S - 1002 -1, 70S 1102 -1,
70S 1701 A, 70S 1402-1, 70S - 1801, 70S 1501, 70S
1202 - 1)
Rolled shutters
Supply and fixing Zn/Al powder coated roller door
consisting 0.6mmthick zink aluminium Powder coated
sheet, pulleys, side plate with the racers and necessary U
209 K-017 channels. All complete to working order. Excluding the m2 8,678.00 9,426.00
covering box and electrical motor.
Grilles
Fabricating & fixing Special security grill fixed for
windows complete with perimeter & either side of
middle opening frame in 16mm x 5mm M.S flat &
5.2mm dia. minimum MS bars at 105mm c/c
210 K-018 horizontally and 135mm c/c vertically welded & fixed m2 9,024.00 9,802.00
to walls with rawl plugs, screws inclusive of two coats
of enamel paint and under two coats of anticorrosive
paint.as per detail drawing No.
CPC/CS/11/04/2017/TYPE-ST/09
Wire mesh
Fabricating & fixing security weld mesh door sash with
locking divice, in GI weld mesh 50mm x 50mm SWG
10, welded on 40mm x 40mm x 5mm MS angle frame
211 K-021 complete with application of two coats enamel paint m2 13,952.00 15,155.00
over two coats of anticorrosive paint complete .as per
detail drawing No. CPC/CS/11/04/2017/TYPE-ST/06

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Fabricating & fixing security weld mesh in open type
buildings in GI weld mesh 50mm x 50mm SWG 10,
welded on 40mm x 40mm x 5mm angle frame complete
212 K-022 with application of two coats enamel paint over two m2 8,032.00 8,725.00
coats of anticorrosive paint complete .as per detail
drawing No. CPC/CS/11/04/2017/TYPE-ST/07
Metal fences
Chain link mesh fence 2.0m high (Gauge 12) with
48mm outer Dia. 3.2mm tk. GI pipe at 2.9m c/c up
rights and 21mm Outer Dia. 1.8mm tk. GI verticle
centre bracing . 48mm Outer Dia. 3.2mm tk. GI pipe at
top and bottom runners, including excavation foundation
213 K-023 concrete work 1:2:4(20mm) welding work, painting of m 9,404.00 10,215.00
two coats of etching primer and finished with one coat
of enamel etc.(Chainlink fence open area 2"x2") All as
per detail drawing No .CPC/CS/11/04/2017/Type-
CLF/01

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION L - WOOD WORK

CARPENTRY
ROOF FRAMING
Supplying and fixing class 1 timber 50mm x 25mm
(nominal) for reepers including application of two
214 L-001 m 158.00 172.00
coats of wood preservative (stain) (only up to 4.6m2
of roof area).
Supplying and fixing Kempas timber 50mm x 25mm
(nominal) for reepers including application of two coats
215 L-002 m 230.00 250.00
wood preservative (stain)( only up to 4.6m2 of roof
area).
(nominal) for battens including application of two coats
216 L-003 m 398.00 433.00
of wood preservative (stain) (only up to 4.6m2 of roof
area).
(nominal) for battons including application of two coats
217 L-004 m 424.00 461.00
wood preservative (stain) ( only up to 4.6m2 of roof
area)
218 L-005 m 1,188.00 1,290.00
coats of wood preservative (stain) ( only up to 4.6m2 of
roof area).
219 L-006 m 1,217.00 1,322.00
coats wood preservative (stain)( only up to 4.6m2 of
roof area)
Supplying and fixing any size (above 100mmx50mm)
class 1 timber beams including application of two coats
220 L-007 m3 239,414.00 260,053.00
of wood preservative (stain) (Only up to 4.6m2 of roof
area).
Supplying and fixing any size (above 100 mm x 50 mm)
Kempas timber beams, including application of two
221 L-008 m3 245,728.00 266,911.00
coats wood preservative(stain) (Only up to 4.6m2 of
roof area).
APPLYING WOOD PRESERVATIVE ON

ROOF FRAME
Applying one coat of wood preservative (stain) on roof
222 L-009 structure for calicut tile roof, measured in plan area. m2 161.00 174.00
Applying two coat of wood preservative (stain) on roof

223 L-010 structure for calicut tile roof measured in plan area. m2 310.00 336.00
Applying one coat of wood preservative (stain) on roof

224 L-011 structure in asbestos roof measured in plan area. m2 120.00 131.00

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Applying two coat of wood preservative (stain) on roof
225 L-012 structure for asbestos roof measured in plan area. m2 205.00 223.00
JOINERY
TIMBER CEILLING
Supplying & Fixing 19mm thick Lunumidella tongued
226 L-013 and grooved Ceiling , under side of rafters, on existing m2 2,062.00 2,240.00
timber frame work.
Supplying & Fixing Flat Lunumidella tongued and
grooved Ceiling 19mm thick complete with timber
frame class 1 100mm x 50mm joists at 0.6m crs. Rate
227 L-014 included for application of wood preservative on timber m2 4,828.00 5,244.00
frame work twice. (Painting measured separately).
ASBESTOES CEILLING
Flat asbestos ceiling Supplying & fixed with wire nails
to 100mm x 50mm joists at 1.2m c/c & 50mm x 50mm
bearers @ 0.6m c/c in class 1 timber including 35mm x
12mm beadings and 50mm x 35mm cove mouldings of
228 L-015 approved timber. Rate included one coat of primer, two m2 4,987.00 5,417.00
coats of emulsion paint to underside of ceiling and two
coats of wood preservative(stain) to timber frame work.
Flat asbestos ceiling Supplying & fixed with wire nails

to 100mm x 50mm joists,1.2m c/c & 50mm x 50mm
bearers at 0.6m c/c in class 1 timber including 35mm x
229 L-016 12mm beadings and 50mm x 35mm cove mouldings of m2 4,354.00 4,729.00
approved timber. Rate included two coats of wood
preservative (stain) on timber frame work.
Fixing flat asbestos ceiling under side of rafters, timber

frame work measured separately, rate included for wire
230 L-017 m2 2,208.00 2,399.00
nails, screws, beadings and mouldings.
Fixing flat asbestos ceiling under side of steel purlins

,50mm x 50mm class 1 timber frame not more than
1.2m x 0.6m crs.includes for wire nails, screws,
231 L-018 beadings and mouldings and 6mm dia. mild steel m2 3,922.00 4,260.00
hanging hooks. Rate included for application of wood
preservative (stain)timber frame.
TIMBER DOORS

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Fabricating & fixing door 28mm ( Nominal 26-28mm)
thick class 1 or above, battened sash with 95mm x
45mm (Nominal) frame, in class 1 or above timber,
oxidized heavy duty furniture 100mm x 62mm iron butt
232 L-019 hinges with in side and out side 100mm barrel bolts , m2 17,819.00 19,356.00
draw ring, painted sashes and frame, two of coats
enamel paint with primer under coats.(3Nos hingers)

thick class 1 or above battened, sash single hung with
95mm x 45mm (Nominal) frame with, Jack timber,
233 L-020 oxidized heavy duty furniture with inside & outside 2 m2 18,776.00 20,395.00
nos 100mm barrel bolt & draw rings. rate included
primer under coats and two coats of enamel paint.(3Nos
of hingers)
thick class 1 or above flush panelled sash single hung
with 95mm x 70mm(Nominal) frame, in treated kempas
timber, oxidized heavy duty furniture, original mortise
234 L-021 door lock approved by engineer,100mm barrel bolts 2 m2 25,651.00 27,863.00
nos etc. rate included primer under coat & two coats of
enamel paint .(3Nos of hingers)

thick, class 1 or above flush panelled sash single hung
with 95mm x 70mm (Nominal) frame, Jack timber,
oxidized heavy duty furniture, original mortise door
235 L-022 lock approved by engineer, 100mm barrel bolts 2 nos m2 26,788.00 29,098.00
etc.rate included primer under coat & two coats of
enamel paint .(3Nos of hingers)

thick class 1 or above panelled & glazed double hung
sashes and top fanlight 95mm x 70mm (Nominal)
frame,treated kempas timber, oxidized heavy duty
236 L-023 furniture, original mortise door lock approved by m2 22,269.00 24,189.00
engineer, Oxidized barrel bolt 2 Nos of 150mm and 2
Nos of 100mm , rate included primer under coat & two
coats of enamel paint.(3pairs of hingers)

thick class 1 or above panelled & glazed double hung
sashes and top fanlight 95mm x 70mm (Nominal)
frame, in Jack timber, oxidized heavy duty furniture,
237 L-024 original mortise door lock approved by engineer, m2 22,821.00 24,789.00
100mm barrel bolt & 150mm barrel bolt, rate included
primer under coat & two coats of enamel paint.(3pairs
of hingers)

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
thick class 1 or above flush panelled, sash with 95mm x
45mm (Nominal) frame, in timber class1or above ,
238 L-025 oxidized heavy duty furniture with inside and out side m2 23,002.00 24,985.00
100mm barrel bolts in lieu of lock and rate included
primer under coat & two coats of enamel paint.(3Nos of
hingers)
thick class 1 or above flush panelled, with 95mm x
45mm (Nominal) frame, in Jack timber, oxidized heavy
239 L-026 duty furniture with inside and outside 100mm bolts in m2 23,147.00 25,143.00
lieu of lock and rate included primer under coat & two
coats of enamel paint. (3Nos of hingers)

thick plywood sash with 95mm x 70mm (Nominal)
treated kempas timber frame, oxidized heavy duty
240 L-027 furniture, original mortise door lock approved by m2 14,870.00 16,151.00
engineer, 1 Nos of 150mm oxidized barrel bolt .rate
included primer under coat & two coats of enamel
paint.(3Nos of hingers)
thick plywood sash with 95mm x 70mm (Nominal) Jack
timber frame, oxidized heavy duty furniture,original
241 L-028 mortise door lock approved by engineer, 1 Nos of m2 16,006.00 17,386.00
150mm oxidized barrel bolt .rate included primer under
coat & two coats of enamel paint.(3Nos of hingers)
Supplying and fixing plywood door sash approved

242 L-029 quality including of oxidized heavy duty furniture etc. m2 3,729.00 4,050.00
(Painting & locks measured separately).
TIMBER WINDOWS
Fabricating and fixing fully glazed window 28mm thick
clas 1 or above sashes and frame with nominal size
95mmx70mm using treated kempas timber complete
243 L-030 with oxidized heavy-duty furniture,3.0mm clear / m2 24,889.00 27,035.00
pinhead glass, including two coats of enamel paint &
primer under coat.
Fabricating and fixing fully glazed window 28mm thick
special class sashes and 95mm x 70mm (Nominal)
frame using Jack timber complete with oxidized heavy
244 L-031 duty furniture, including two coats of enamel paint & m2 30,284.00 32,894.00
primer under coat. (Glass thickness 3.0mm clear /
pinhead).
DOOR,WINDOW FRAMES
Supplying & fixing door, window frames new, measured
245 L-032 length of timber using treated kempas, 95mm x m 1,238.00 1,345.00
45mm (Nominal).

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Supplying & fixing door, window frames new, measured
246 L-033 length of timber using treated kempas, 95mm x 70mm m 1,748.00 1,899.00
(Nominal)..
Supplying & fixing door/ window frames with new jack
247 L-034 m 1,514.00 1,645.00
timber 95mm x 45mm (Nominal)..
Supplying & fixing door/ window frames with new jack
248 L-035 m 2,112.00 2,294.00
timber 95mm x 70mm (Nominal)..
Supplying & fixing door, window 28mm thick new sash
249 L-036 m2 10,504.00 11,410.00
glazed or panelled class1or above timber.
Supplying & fixing door, window 28mm thick sash new
250 L-037 m2 18,010.00 19,563.00
glazed or panelled special or above.
IRON MONGERY
DOOR FURNITURE
Supplying & fixing butt hinges brass 100mm x 62mm
251 L-038 Pair 1,105.00 1,201.00
with brass screws.
Supplying & fixing butt hinges oxidized iron 100mm
252 L-039 Pair 733.00 796.00
x 62mm with iron screws.
Supplying & fixing brass barrel bolts 100mm with brass
253 L-040 nr 683.00 742.00
screws.
Supplying & fixing oxidized iron barrel bolts 100mm
254 L-041 nr 350.00 380.00
with iron screws.
Supplying & fixing brass barrel bolts 150mm with
255 L-042 nr 719.00 781.00
brass screws.
Supplying & fixing oxidized iron barrel bolts 150mm
256 L-043 nr 379.00 412.00
with iron screws.
Supplying & fixing lock rim or night latch (Chinese) .
257 L-044 nr 1,838.00 1,996.00
Supplying & fixing double hung mortise type door lock
258 L-045 nr 5,773.00 6,271.00
approved by engineer.
Supplying & fixing single hung mortise type door lock
259 L-046 nr 5,481.00 5,953.00
approved by engineer.
260 L-047 Supplying and fixing door rings 40mm dia . nr 243.00 264.00
Supplying & fixing hasp & staple 100mm to 150mm.(
261 L-048 nr 578.00 628.00
Pad lock Measured seperatly)
WINDOW FURNITURE
Supplying & fixing casement stays 250mm iron
262 L-049 nr 266.00 289.00
oxidized.
Supplying & fixing casement stays 300mm brass
263 L-050 nr 629.00 684.00
,circular type with brass screws.
Supplying & fixing casement fasteners Iron oxidized .
264 L-051 nr 259.00 282.00

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION N - PARTITIONS/
LININGS/SUSPENDED CEILINGS
DEMOUNTABLE PARTITONS
Fabricating and fixing TYPE-01 Anodized Aluminium
partition with aluminium architectural sections with 10 -
15 micron coating glazed and panelled with 3mm ,
265 N-001 plastic coated ply board to both sides,at bottom and m2 6,997.00 7,600.00
4.6mm thick glass at top.(The used section SPR 105,
SPR 106, SPR 110, SPR 107, SPR 4521)
Fabricating and fixing TYPE-02 Anodized Aluminium

SPR 106, SPR 110, SPR 107, SPR 4521)
Fabricating and fixing TYPE -03 Anodized Aluminium

SPR 106, SPR 110, SPR 107, SPR 4521)
Fabricating and fixing TYPE -04 Anodized Aluminium

SPR 106, SPR 110, SPR 107, SPR 4521)
Fabricating and fixing TYPE-01 Powder coated

aluminium partition with aluminium architectural
269 N-005 panelled with 3mm , plastic coated ply board to both m2 7,529.00 8,178.00
sides, at bottom and 4.6mm thick glass at top.(The used
section SPR 105, SPR 106, SPR 110, SPR 107, SPR
4521)
Fabricating and fixing TYPE-02 Powder coated
4521)

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Fabricating and fixing TYPE -03 Powder coated
sides,at bottom and 4.6mm thick glass at top.(The used
4521)
Fabricating and fixing TYPE -04 Powder coated
4521)
SUSPENDED GRID SYSTEM CEILINGS

Fabricating and fixing suspended type ceiling
PVC/Mineral fiber board/Cement Board ceiling with T
273 N-009 and and L sections complete as per detailed drawing. m2 1,374.00 1,493.00
(Ceiling panel rate not included.) Panel size 600mm x
600mm.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION P - ROOF COVERING /
ROOF PLUMBING
TILE ROOF COVERING

Supplying and laying calicut pattern tiles, in any type of
274 P-001 m2 1,316.00 1,430.00
roof.
Forming Plaster bands in 1:1:5 cement, lime and sand to
275 P-002 m 144.00 156.00
tiled roof coloured to match tiles.
Laying calicut pattern ridge tile bedded in cement, lime
276 P-003 m 885.00 961.00
and sand motar 1:1:5 coloured to match tiles.
Fixing ridge tiles (available) laid on roof, 1:1:5 cement,
277 P-004 lime and sand bedding and coloured to match tiles. m 589.00 640.00
SHEET ROOF COVERING
ZN/AL SHEET
Supplying & fixing 0.47mm thick colour Zn/Al. roofing
278 P-005 sheets with self drilling screws (fasteners) on frame m2 2,037.00 2,212.00
work - Frame work measured separately.
Supplying & Fixing 0.47mm thick Zn / Al sheets- Tile
profile,with self drilling Screws (Fasteners) on frame
279 P-006 m2 2,116.00 2,298.00
work -Frame Work Measured Seperatly (Single &
Double roof).
Supplying & Fixing 0.47mm thick Zn / Al sheets ,Tile
profile ,with self drilling Screws (Fasteners) on frame
280 P-007 m2 2,171.00 2,359.00
work - Frame Work Measured Seperatly) . (Hip roof)
Supplying & Fixing 0.47mm thick Zn / Al sheets with

281 P-008 self drilling Screws (Fasteners) on frame work - Frame m2 2,090.00 2,270.00
Work Measured Seperatly . (Hip roof)
ASBESTOS SHEETS
Supplying and fixing new asbestos roofing sheets
confirming to SLS 9 on existing framework with new
282 P-009 nut and bolts, apply two coats of emulsion paint under m2 1,901.00 2,065.00
side of sheet etc. (Frame work measured separately).
Supplying and fixing Asbestos roofing sheets on 62mm

x 62mm x 6mm MS purlins not exceeding 1.35m
crs.complete with necessary bolts / welds GI roofing
bolts at not more than 0.55m crs. on every purlin,
283 P-010 appling two coats of anticorrosive paint and appling two m2 2,951.00 3,205.00
coats of emulsion paint underside of sheets. Rate
included 20mm x 6mm flat iron brackets for fixing
valance board at 0.6m c/c.
FLASHING/RIDGES/CAPPINGS

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Supplying & Fixing 0.47mm thick Zn / Al Flashing
284 P-011 with self drilling Screws (Fasteners) & rawl plugs. m 1,819.00 1,976.00
nominal girth 470mm .
Fixing close fitting type asbestos ridging pairs with
285 P-012 m 1,309.00 1,422.00
necessary bolts.
Supplying & fixing 0.47mm thick colour Zn /Al. ridge
286 P-013 cap/ bottom ridge cap with self drilling screws m 1,758.00 1,909.00
(Fasteners) minimum girth 470mm.
Supplying & fixing 0.47mm thick colour Zn /Al. barge
287 P-014 capping with self drilling screws (Fasteners) . m 1,664.00 1,808.00
Supplying & fixing 0.47mm thick colour Zn /Al. edge

288 P-015 m 1,664.00 1,808.00
capping with self drilling screws (Fasteners) .
FIXING ALUMINIUM FOIL

Supplying and laying 75mm x 75mm gauge 17 welded
289 P-016 m2 282.00 307.00
wire mesh under the roof as directed.
Supplying and laying of laminated aluminium foil, 4mm
thick double side double bubble insulation layer, under
290 P-017 m2 605.00 657.00
the roof as directed. (Ultra bubble reflective layer)
ROOF PLUMBING
Supplying and fixing Gutters 0.47mm thick colour Zn
291 P-018 /Al 457mm girth with brackets not exceeding 0.6m crs. m 1,674.00 1,819.00
rate includes for specials.
Supplying and fixing PVC gutters square type 150mm
with PVC brackets not exceeding 225mm fixed to
292 P-019 m 1,050.00 1,140.00
valance board using 20 mm wire nails, rate includes for
specials.
Fabricating and fixing Valley gutters and flashing in GI
sheets G22, including application of two coats of hot tar
293 P-020 m 1,808.00 1,964.00
and blinding with sand (timber board measured
separately) 900mm wide.
Supplying & Fixing 0.47mm thick Zn / Al Valley
294 P-021 m 1,714.00 1,861.00
gutters including Screws. Nominal girth 470mm .
Supplying and fixing class1 Timber boarding , 20mm to
25mm thick for valley gutters, flashings etc, inclusive of
295 P-022 applying two coats of wood preservative (stain) ( Only m2 5,794.00 6,294.00
up to 4.6m2 of roof area).
Supplying and fixing valance boards beaded 225mm x

20mm thick Ginisapu, including one coat of primer and
296 P-023 m 1,510.00 1,641.00
two coats of enamel paint (Flat iron bracket measured
separately) .
Supplying & Fixing 0.47mm thick Zn / Al Valance
297 P-024 m 1,758.00 1,909.00
board including Screws. Nominal girth 470mm .
Extra over Supplying & Fixing 20x 6mm flat iron
298 P-025 valance board bracket at 0.6m c/c (total length 375mm) nr 371.00 403.00
including welding works, painting etc.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Supplying and fixing down pipes PVC 90mm dia. with
brackets not exceeding 1.2m well secured to walls with
299 P-026 m 775.00 842.00
plastic rawl plugs. (Rate includes for specials).
Supplying and fixing down pipes colour Zn/Al 0.47mm

thick 100mm X 100mm with brackets not exceeding
300 P-027 m 1,485.00 1,613.00
1.2m crs. of the pipe, rate includes for specials.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION Q - PLUMBING / SANITARY

INSTALLATION
Pipes
Supplying and laying Pipes pvc with specials, size
301 Q-001 63mm dia. in waste water lines, vent pipes etc. (Type m 792.00 860.00
400/ Class 4)
Supplying and laying Pipes PVC with specials, size
302 Q-002 m 914.00 993.00
50mm dia. in wastes of sinks. Type 600.(PNT 7)
Supplying and laying Pipes PVC type 600 (PNT 7) with
303 Q-003 specials, size 40mm dia. in waste of wash basins. m 471.00 512.00
Supplying and laying Pipes pvc with specials, size

304 Q-004 m 1,373.00 1,491.00
63mm dia. (Type 1000/ PNT 11) .
50mm dia. rate includes for cutting trenches, testing and
305 Q-005 m 939.00 1,020.00
backfilling. (Type 1000/ PNT 11) depth of the trench
not less than 450mm.
Supplying and laying Pipes PVC type 1000 (PNT 14)
with specials, size 40mm dia. Rate includes for cutting
306 Q-006 m 758.00 823.00
trenches, testing and backfilling. Depth of the trench not
less than 450mm.
32mm dia. (Type 1000/PNT 11) rate includes for
307 Q-007 m 630.00 684.00
cutting trencthes,testing and backfilling, depth of the
trench not less than 450mm.
25mm dia. type 1000 (PNT 11) rate includes for cutting
308 Q-008 m 481.00 523.00
trenches, testing and backfilling. Depth of the trench not
less than 450mm.
20mm dia. type 1000 (PNT 14) rate includes for cutting
309 Q-009 m 372.00 404.00
trenches, testing and back filling. Depth of the trench
not less than 450mm.
310 Q-010 m 489.00 532.00
32mm dia. (Type 1000/PNT 11) on wall
311 Q-011 m 341.00 370.00
25mm dia. type 1000 (PNT 11) on wall
312 Q-012 m 232.00 252.00
20mm dia. type 1000 (PNT 14) on wall
Fixtures appliances and equipment

Supplying & fixing 20mm(1/2") dia. bidet spray
313 Q-013 nr 3,633.00 3,946.00
approved best quality.(chromium plated)
Supplying & fixing approved cistern plastic with
314 Q-014 nr 6,790.00 7,375.00
20mm(1/2") chromium plated flexible hose.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Supplying & fixing approved Closet ,with working
order including 20mm(1/2")dia. chromium plated angle
315 Q-015 nr 5,023.00 5,456.00
valve and chromium plated flexible hose. (Closet cost
not included.)
Supplying & fixing Bowl type approved urinal with trap
316 Q-016 and urinal flush valve complete to working order. nr 11,306.00 12,280.00
Supplying & fixing approved new closet squatting foot

rest type (Orissa pan) with trap, supplied and fixed to
317 Q-017 nr 14,438.00 15,683.00
working order including connection to sewer line.
Supplying & fixing mirror for bathroom 450mm x

318 Q-018 600mm size approved quality with screws, plugs etc. nr 2,676.00 2,907.00
Supplying & fixing approved sink stainless steel with

single drain board with chromium plated wastewater
319 Q-019 chain, stay & waste plug (tap, brackets, water , waste nr 7,917.00 8,600.00
water connection & brick work measured separately).
Supplying & fixing approved Sink Stainless Steel

Single drain board ( Rocell ADRIAN 611 TRENDY
915 X 480mm or equivalent) with chromium plated
320 Q-020 wastewater chain, stay & Waste Plug (Rocell A38, A43 nr 23,790.00 25,841.00
or equivalent) (tap, brackets, water , waste water
connection & brick work measured separately).
Supplying & fixing approved ceramic sink 600mm x

375mm x 175mm overall size and chromium plated
swan neck type piller tap complete with waste plug,
321 Q-021 chromium plated waste chain & stay ( water nr 17,286.00 18,776.00
connection, waste water connection & brick work
measured separately).
Supplying & fixing Wash basin with pedestal Vitreous
China 575 X 450 X 820mm ( Rocell urban D or
equivalent) and Chromium Plated Sawn neck Type
Piller Tap (Rocell N091214 or equivalant) complete
322 Q-022 with Waste Plug (Rocell A38, A43 or equivalent), nr 24,752.00 26,885.00
chromium plated waste chain & stay ( water
connection, waste water connection & brick work
measured separately).
Supplying & fixing approved sink ceramic laboratory
supplying and fixing complete with waste, chromium
323 Q-023 plated waste chain, stay and waste plug. (tap, water & nr 11,456.00 12,444.00
waste water connection, brick work measured
separately).
Supplying and fixing approved corner wash basin
ceramic with 20mm(1/2") dia. chromium plated pillar
324 Q-024 tap, waste plug, chain and stay.(water connection and nr 11,646.00 12,649.00
wastewater connection measured separately).

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Supplying and fixing Ceramic Corner Wash Basin
(Rocell - Aqua RB.ACO.01G101.01.06 or equivalent)
with 20mm(1/2") dia. Cromium plated Piller tap - Rocel
325 Q-025 Vero or equalent, Waste Plug (Rocell A38, A43 or nr 19,816.00 21,525.00
equivalent), chain and stay.(water connection and
wastewater connection measured separately).
Fixing wash basin supplied with 20mm(1/2") dia.

Cromium plated Piller tap - Rocel Vero or equalent,
326 Q-026 waste plug, chain and stay.(Water connection and waste nr 9,157.00 9,947.00
water connection measured separately).(Wash basin rate
not included).
Supplying and fixing 20mm(1/2") dia. Approved, brass
heavy quality chromium plated Angle Value with
327 Q-027 nr 1,737.00 1,886.00
20mm(1/2") dia. P.V.C. Faucept Socket .
Supplying & fixing 20mm(1/2") pipe dia.,150mm

328 Q-028 nr 2,891.00 3,140.00
approved chromium plated shower rose.
Supplying and fixing 20mm(1/2") pipe dia. Chromium
329 Q-029 plated Shower rose (Rocell FHS 30A or Equivalent). nr 7,810.00 8,483.00
Water Tanks
Supplying and installing 1000 L capacity water tank
made of polymer materials of approved quality on sand
330 Q-030 nr 16,640.00 18,074.00
bed. Rate for only water tank. PVC pipes, valves,
fittings measured separately.
Supplying and installing 2000 L capacity water tank
made of polymer materials of approved quality on sand
331 Q-031 nr 29,241.00 31,761.00
bed. Rate for only water tank. PVC pipes, valves,
fittings measured separately.
Supplying and installing 500 L capacitywater tank made
of polymer materials of approved quality on sand bed.
332 Q-032 nr 10,879.00 11,817.00
Rate for only water tank. PVC pipes, valves, fittings
measured separately.
Cocks
Supplying and fixing Ball cock brass size 20mm dia.
333 Q-033 nr 1,498.00 1,627.00
heavy quality.
Supplying and fixing Ball cock plastic size 25mm dia.
334 Q-034 nr 495.00 538.00
335 Q-035 nr 419.00 455.00
336 Q-036 nr 669.00 726.00
Valves
Supplying and fixing Gate valve ,brass, size 20mm dia.
337 Q-037 nr 1,530.00 1,662.00
heavy quality.
Supplying and fixing Gate valve, brass, size 32mm dia.
338 Q-038 nr 2,066.00 2,244.00
heavy quality.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Supplying and fixingGate valve brass, size 40mm dia.
339 Q-039 nr 4,753.00 5,163.00
heavy quality.
340 Q-040 nr 6,816.00 7,404.00
heavy quality.
341 Q-041 nr 5,674.00 6,163.00
heavy quality.
Supplying and fixing Ball valve ,brass,size 20mm dia.
342 Q-042 nr 1,194.00 1,297.00
Supplying and fixing Ball valve brass size 25mm dia.
343 Q-043 nr 1,601.00 1,739.00
Supplying and fixing Ball valve ,brass, size 32mm dia.
344 Q-044 nr 2,474.00 2,688.00
Supply and fix 20mm dia Cromium plated Brass
345 Q-045 nr 4,258.00 4,612.00
Conseal Valve
Taps
Supplying and fixing 20mm(1/2") dia. General approved
chromium plated heavy quality swan neck type pillar tap
346 Q-046 nr 3,337.00 3,624.00
with 01 No. P.V.C. Faucept Socket to existing wash
basin/sink.
Supplying and fixing 20mm(1/2") dia. Approved, heavy
347 Q-047 quality chromium plated bib tap with 20mm(1/2") dia. nr 2,713.00 2,947.00
P.V.C. Faucept Socket .
Supplying and fixing 20mm(1/2") dia. approved plastic
348 Q-048 nr 576.00 626.00
bib tap with 1 No.P.V.C Faucept Socket .
Construction of Stand post with 0.9m x 0.9m x 0.15m
grade 20 concrete base and 0.15m x 0.15m x 0.75m
RCC post, 20mm(1/2") plastic bib tap. Inclusive of
349 Q-049 20mm PVC pipe connection. Concrete base and post to nr 11,695.00 12,703.00
be rendered with 1:3 cement and sand finished smooth.
(PVC supplied pipe measured separately).
Stopcock pits, Valve chambers

Constructing Valve chamber 225mm x 225mm x
225mm in 1:2:4(20mm) concrete, complete with RCC
350 Q-050 nr 4,462.00 4,846.00
lid, necessary lifting hooks,R113 cement rendered in
innner surfaces.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION R - MECHANICAL
INSTALLATIONS
Split type air conditioning machines
Supply and installation of 12000BTU split type air
351 R-001 conditioner (Non-inverter type) unit in working nr 108,958.00 118,351.00
order.(Up to 5m Piping & casing Installation)
352 R-002 conditioner(Inverter type) unit in working order.(Up to nr 122,252.00 132,791.00
5m Piping & casing Installation)
353 R-003 conditioner ( Non Invertor type) unit in working nr 142,935.00 155,257.00
order.(Up to 5m Piping & casing Installation)
354 R-004 conditioner (Inverter type) unit in working order. (Up to nr 155,872.00 169,310.00
355 R-005 conditioner ( Non Invertor type) unit in working order. nr 148,638.00 161,452.00
(Up to 5m Piping & casing Installation)
356 R-006 conditioner (Inverter type) unit in working order. (Up to nr 173,396.00 188,344.00
357 R-007 conditioner ( Non Invertor type ) unit in working order. nr 318,675.00 346,147.00
(Up to 5m Piping & casing Installation)
358 R-008 conditioner ( Invertor type) unit in working order. (Up nr 539,943.00 586,490.00
to 5m Piping & casing Installation)

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION S - ELECTRICAL
INSTALLATIONS
Note;
* All electrical installation shall be done according
th
to the IET wiring regulations - 18 Edition - ( BS
7671: 2018)
* All MCCB, RCD, MCB and Isolators shall be
Europian, Japanese or equivalent.
* All types of fans shall be approved quality and
shall have minimum one year warranty period.
* Ceiling fans shall be complied with the SLS 814

and shall have cut-off safety switch and safety
wire provided to prevent detachment of fan motor
from the rod.
* All types of LED lamp fittings should have
minimum two year warranty period.
* Samples of all materials shall be approved by the
engineer, prior to the installation.
Installation of Power cable in Conduits

Supply and installation of 2 x 1 mm2 Cu/PVC/PVC
359 S-001 m 166.00 181.00
cables concealed in conduits.
Supply and installation of 2 x 1.5 mm2 Cu/PVC/PVC
360 S-002 m 217.00 235.00
361 S-003 m 301.00 327.00
362 S-004 m 421.00 457.00
Supply and installation of 2 x 6 mm2 Cu/ PVC/ PVC
363 S-005 m 561.00 609.00
364 S-006 m 871.00 946.00
365 S-007 m 1,224.00 1,329.00
366 S-008 m 1,870.00 2,031.00
367 S-009 Supply and installation of 2 x 1 mm2 Cu/PVC/PVC + m 225.00 244.00

2.5 mm2 E cables concealed in conduits.
368 S-010 Supply and installation of 2 x 1.5 mm2 Cu/PVC/PVC + m 275.00 299.00
Supply and installation of 2 x 4 mm2 Cu/ PVC/ PVC +
370 S-012 m 552.00 599.00
4 mm2 E cables concealed in conduits.
Supply and installation of 2 x 6 mm2 Cu/PVC/PVC + 6
371 S-013 m 793.00 861.00
mm2 E cables concealed in conduits.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
372 S-014 Supply and installation of 2 x 10 mm2 Cu/PVC/PVC + m 1,176.00 1,278.00

10 mm2 cables concealed in conduits.

16mm2 E cables concealed in conduits.

375 S-017 m 799.00 868.00
376 S-018 m 1,079.00 1,172.00
377 S-019 m 1,581.00 1,717.00
378 S-020 m 2,219.00 2,410.00
379 S-021 m 3,494.00 3,795.00
Supply and installation of 4 x 35 mm2 PVC/XLPE/Cu
380 S-022 m 4,547.00 4,939.00
381 S-023 Supply and installalation of 4 x 4 mm2 Cu/PVC/PVC + m 997.00 1,083.00

382 S-024 m 1,303.00 1,416.00
mm2 E cables concealed in conduits.


385 S-027 m 4,059.00 4,409.00
+ 16mm2 E cables concealed in conduits.
386 S-028 Supply and installation of 4 x 35 mm2 PVC/XLPE/Cu m 5,243.00 5,695.00

+ 25 mm2 E cables concealed in conduits.
Installation of Power cable in Casing.

387 S-029 m 222.00 242.00
cables concealed in casing.
388 S-030 m 273.00 296.00
389 S-031 m 357.00 387.00
390 S-032 m 477.00 518.00
Supply and installalation of 2 x 6 mm2 Cu/PVC/PVC
391 S-033 m 671.00 729.00
392 S-034 m 912.00 991.00

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
393 S-035 m 1,267.00 1,376.00
394 S-036 m 1,913.00 2,078.00
395 S-037 Supply and installation of 2 x 1 mm2 Cu/PVC/PVC + m 289.00 314.00

2.5 mm2 E cables concealed in casing.
398 S-040 Supply and installation of 2 x 4 mm2 Cu/PVC/PVC + 4 m 589.00 640.00

mm2 E cables concealed in casing.
399 S-041 m 834.00 906.00
mm2 E cables concealed in casing.

10 mm2 E cables concealed in casing.

16mm2 E cables concealed in casing.

16mm2 E cables concealed in casing.
403 S-045 m 889.00 966.00
404 S-046 m 1,151.00 1,250.00
405 S-047 m 1,848.00 2,007.00
406 S-048 m 2,461.00 2,673.00
407 S-049 m 4,094.53 4,447.51
Supply and installation of 4 x 35 mm2 PVC/XLPE/Cu
408 S-050 m 4,990.00 5,420.00
409 S-051 m 1,002.00 1,088.00
410 S-052 m 1,314.00 1,427.00
411 S-053 m 2,107.00 2,289.00
+ 10 mm2 E cables concealed in casing.
412 S-054 m 3,236.00 3,515.00
+ 16mm2 E cables concealed in casing.
413 S-055 m 4,510.00 4,899.00
+ 16mm2 E cables concealed in casing.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
414 S-056 Supply and installation of 4 x 35 mm2 PVC/XLPE/Cu m 5,695.00 6,186.00

+ 25 mm2 E cables concealed in casing.
Installation of Earth cable in Conduits.

Supply and installation of 2.5 mm2 earth cable
415 S-057 m 172.00 187.00
concealed in conduit.
Supply and installation of 4 mm2 earth cable concealed
416 S-058 m 218.00 237.00
in conduit.
417 S-059 m 268.00 291.00
in conduit.
418 S-060 m 373.00 406.00
in conduit.
419 S-061 m 545.00 592.00
in conduit.
420 S-062 m 834.00 906.00
in conduit.
421 S-063 m 1,048.00 1,138.00
in conduit.
Installation of Earth cable in Casing.

Supply and installation of 2.5 mm2 earth cable
422 S-064 m 236.00 257.00
concealed in casing.
423 S-065 m 282.00 306.00
in casing.
424 S-066 m 332.00 361.00
in casing.
425 S-067 m 438.00 475.00
in casing.
426 S-068 m 656.00 712.00
in casing.
427 S-069 m 944.00 1,026.00
in casing.
428 S-070 m 1,150.00 1,250.00
in casing.
Installation of armoured cables
(Underground or on trays )
Supply and installation of 2 x 4 mm2

429 S-071 m 1,024.00 1,112.00
Cu/PVC/SWA/PVC - armoured cables (Excluding floor
excavation, civil works or cable tray installations)

430 S-072 m 1,224.00 1,330.00

431 S-073 m 1,528.00 1,660.00

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
432 S-074 Cu/PVC/SWA/PVC cables (Excluding floor excavation, m 2,125.00 2,308.00
civil works or cable tray installations)
Supply and installation of 4 x 2.5 mm2

433 S-075 m 774.00 841.00

434 S-076 m 1,127.00 1,224.00

435 S-077 m 1,474.00 1,601.00

436 S-078 m 2,277.00 2,473.00

437 S-079 m 2,982.00 3,239.00

438 S-080 m 2,830.00 3,074.00
Cu/XLPE/SWA/PVC - Armoured cables (Excluding
floor excavation, civil works or cable tray installations)
Supply and installation of 2 x 35mm2

439 S-081 m 3,730.00 4,052.00
Cu/XLPE/SWA/PVC - armoured cables (Excluding

440 S-082 m 3,882.00 4,217.00

441 S-083 m 4,685.00 5,089.00
Earthing Electrodes
Supply and installation of of 4 feet Cu earth electrode
442 S-084 with 16mm diameter and other accessories in working nr 2,234.00 2,427.00
order.
Supply and installation of 5 feet GI pipe with 2 inch
443 S-085 diameter as an earth electrode and other accessories in nr 5,377.00 5,841.00
working order.
Point wiring through conduits for Socket
outlets -13A, Data & Telephone.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
13 A socket outlet / grouped socket outlets - point
wiring to be carried out with 2 x 2.5 mm2 PVC
insulated PVC sheathed copper cables and 2.5 mm2
444 S-086 nr 3,693.00 4,012.00
earth cable wired in concealed conduit in wall and
above ceiling, to be supplied and installed in working
order.
13 A socket outlet to be controlled by 20A D/pole

switch with neon indicator - point wiring to be carried
445 S-087 out with 2 x 2.5 mm2 PVC insulated PVC sheathed nr 4,610.00 5,007.00
copper cables and 2.5 mm2 earth cable wired in
concealed conduit in wall and above ceiling ,to be
supplied and installed in working order.
Data socket outlet ( RJ 45 ) - point wiring to be carried

446 S-088 out with 5U/ UTP AWG 24 CAT 5E PVC cables wired nr 2,378.00 2,583.00
in concealed conduit in wall and above ceiling, to be

in concealed conduit in wall and above ceiling ,to be
Telephone socket outlet ( RJ 11 ) - point wiring to be

448 S-090 carried out with 2 x 0.5 mm2 Single Pair - BS 10653 nr 1,882.00 2,044.00
cables wired in concealed conduit in wall and above
ceiling ,to be supplied and installed in working order.

449 S-091 carried out with 2 x 0.5 mm2 two Pair - BS 10653 nr 2,094.00 2,274.00
cables wired with PVC casing on wall and on soffit of
the slabs to be supplied and installed in working order.
Point wiring through conduits for lamps and
fans.
Pendant type lamp point wiring to be carried out with 2

450 S-092 x 1.0 mm2 PVC insulated PVC sheathed copper cables nr 2,429.00 2,638.00
wired in concealed conduit in wall and above ceiling, to
be supplied and installed in working order.
2 numbers of pendant type lamp points to be controlled

by one switch - point wirings to be carried out with 2 x
451 S-093 nr 3,467.00 3,766.00
1.0 mm2 PVC insulated PVC sheathed copper cables

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.

452 S-094 nr 4,505.00 4,893.00

453 S-095 nr 5,543.00 6,021.00
Recessed type / surface mounted type / ceiling mounted

type lamp point wiring to be carried out with 2 x 1.0
454 S-096 nr 2,125.00 2,308.00
mm2 PVC insulated PVC sheathed copper cables wired
2 numbers of recessed type / surface mounted type /

ceiling mounted type lamp point to be controlled by one
455 S-097 switch - point wirings to be carried out with 2 x 1.0 nr 2,859.00 3,105.00


Indoor bracket lamp point wiring to be carried out with

458 S-100 2 x 1.0 mm2 PVC insulated PVC sheathed copper nr 2,125.00 2,308.00
cables wired in concealed conduit in wall and above
ceiling, to be supplied and installed in working order..
2 numbers of indoor bracket lamp points to be
controlled by one switch - point wirings to be carried
out with 2 x 1.0 mm2 PVC insulated PVC sheathed
459 S-101 nr 2,859.00 3,105.00
copper cables wired in concealed conduit in wall and
order.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
460 S-102 nr 3,593.00 3,903.00
copper cables wired in concealed conduit in wall and
order.
Stairway lamp point wiring with two way switch - to be
carried out with 2 x 1.0 mm2 PVC insulated PVC
461 S-103 sheathed copper cables wired in concealed conduit in nr 3,805.00 4,133.00
wall and above ceiling, to be supplied and installed in
working order.
Watertight lamp point wiring - to be carried out with 2

2 numbers of watertight lamp points to be controlled by

one switch - point wirings to be carried out with 2 x 1.0
463 S-105 nr 2,859.00 3,105.00

464 S-106 nr 3,593.00 3,903.00
supplied and installed in working order..

465 S-107 nr 4,327.00 4,700.00
supplied and installed in working order..
Ceiling fan point wiring completed with fan hook - to

be carried out with 2 x 1.0 mm2 PVC insulated PVC
466 S-108 nr 2,629.00 2,856.00
sheathed copper cables and 2.5 mm2 earth cable wired
Point wiring through PVC casing for Socket
13 A socket outlet / grouped socket outlets - point
wiring to be carried out with 2 x 2.5 mm2 PVC
insulated PVC sheathed copper cables and 2.5 mm2
467 S-109 nr 4,029.00 4,376.00
earth cable wired with PVC casing on wall and on soffit
of the slabs to be supplied and installed in working
order.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
13 A socket outlet to be controled by 20A D/pole switch
with neon indicator - point wiring to be carried out with
2 x 2.5 mm2 PVC insulated PVC sheathed copper
468 S-110 nr 4,946.00 5,372.00
cables and 2.5 mm2 earth cable wired with PVC casing
on wall and on soffit of the slabs to be supplied and
installed in working order.

with PVC casing on wall and on soffit of the slabs to be


471 S-113 carried out with 2 x 0.5 mm2 Single Pair - BS 10653 nr 2,162.00 2,348.00

472 S-114 carried out with 2 x 0.5 mm2 Two Pair - BS 10653 nr 2,373.00 2,578.00
Point wiring through PVC casing for lamps
and fans.
Pendent type lamp point wiring - to be carried out with

473 S-115 2 x 1.0 mm2 PVC insulated PVC sheathed copper nr 2,761.00 2,999.00
the slabs to be supplied and installed in working order .
2 numbers of pendent lamp points to be controlled by

474 S-116 nr 3,910.00 4,247.00
supplied and installed in working order .

475 S-117 nr 5,106.00 5,546.00

476 S-118 nr 6,255.00 6,794.00

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Recessed type / surface mounted type / ceiling mounted

type lamp point wiring - to be carried out with 2 x 1.0
477 S-119 nr 2,457.00 2,669.00

ceiling mounted type lamp points to be controlled by
478 S-120 one switch- point wirings to be carried out with 2 x 1.0 nr 3,302.00 3,586.00


Indoor bracket lamp point wiring - to be carried out

481 S-123 with 2 x 1.0 mm2 PVC insulated PVC sheathed copper nr 2,457.00 2,669.00
482 S-124 nr 3,302.00 3,586.00
copper cables wired with PVC casing on wall and on
soffit of the slabs to be supplied and installed in
working order.
483 S-125 nr 4,147.00 4,504.00
copper cables wired with PVC casing on wall and on
soffit of the slabs to be supplied and installed in
working order.
Stairway lamp point wiring - to be carried out with 2 x

484 S-126 1.0 mm2 PVC insulated PVC sheathed copper cables nr 4,377.00 4,754.00
wired with PVC casing on wall and on soffit of the slabs
to be supplied and installed in working order.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Watertight lamp point wiring - to be carried out with 2

wired with PVC casing on wall and on soffit of the slabs
to be supplied and installed in working order.

486 S-128 nr 3,302.00 3,586.00

487 S-129 nr 4,147.00 4,504.00
with PVC casing on wall and on soffit to be supplied
and installed in working order.

488 S-130 nr 4,992.00 5,422.00
Ceiling fan point wiring completed with fan hook - to

be carried out with 2 x 1.0 mm2 PVC insulated PVC
489 S-131 nr 2,961.00 3,216.00
sheathed copper cables and 2.5 mm2 earth cable wired
Point wiring through PVC casing for Socket
Supply and installation of of 13 A socket outlet in
490 S-132 nr 797.00 866.00
working order .
Supply and installation of of 13 A socket outlet with
491 S-133 nr 814.00 884.00
neon indicator in working order.
Supply and installation of of 16A / 32A 3 pin industrial
492 S-134 nr 1,509.00 1,639.00
socket outlet in working order.
Supply and installation of of 16A / 32A 5 pin industrial
493 S-135 nr 1,618.00 1,757.00
socket outlet in working order.
Supply and installation of of RJ 45 data socket outlet in
494 S-136 nr 2,495.00 2,710.00
working order.
Supply and installation of of RJ 11 telephone socket
495 S-137 nr 976.00 1,061.00
outlet in working order.
Supply and installation of of socket outlet including
496 S-138 data outlet and telephone outlet on one plate, in working nr 2,441.00 2,651.00
order.
Installation of Lamp fittings

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Supply and installation of pendent type 200mm dia.
conical polycarbonate lamp shade and 15W CFL bulb
497 S-139 nr 821.00 891.00
(CFL bulb shall be 4 stars rated or greater) in working
order.
498 S-140 Supply and installation of 15 W CFL globe (CFL bulb nr 631.00 685.00
shall be 5 stars rated or greater) in working order.
Supply and installation of 7 W LED Globe in working
499 S-141 order (Efficacy shall be eaqual or greater than 80 lm / nr 425.00 461.00
W).
Supply and installation of recessed type 1200mm x
300mm fluorescent lamp fitting completed with polished
500 S-142 aluminium double parabolic louver and 2 numbers of nr 5,727.00 6,220.00
36 W,1200mm fluorescent bulbs in working order.
(with electronic ballest)
Supply and installation of recessed type 600mm x
600mm fluorescent lamp fitting completed with polished
501 S-143 aluminium double parabolic louver and 3 numbers of nr 5,998.00 6,515.00
18 W,600mm fluorescent bulbs in working order.
(With electronic ballest)
Supply and installation of 1200mm fluorescent lamp
fitting completed with prismatic diffuser and 1 number
502 S-144 nr 1,946.00 2,113.00
of 36W,1200mm fluorescent bulb in working order.
(With electronic ballest)

503 S-145 fitting completed with prismatic diffuser and 2 numbers nr 2,759.00 2,997.00
of 36W, 1200mmx175mm(+-10%) fluorescent bulb in
working order. (with electronic ballest).
fitting completed with prismatic diffuser and 1 number
504 S-146 nr 1,837.00 1,995.00
of 18W, 600mm fluorescent bulb in working order.
(With Electronic ballest).
fitting completed with opal white diffuser and 1 number
505 S-147 nr 2,488.00 2,702.00
of 18w, 600mm fluorescent bulb in working order.
(With electronic ballest).
fitting completed with opal white diffuser and 1 number
506 S-148 nr 3,030.00 3,292.00
of 36w,1200mm fluorescent bulb in working order.
(With electronic ballest).

507 S-149 fitting completed with opal white diffuser and 2 nr 4,061.00 4,411.00
numbers of 36w, 1200mmx175mm(+-10%) fluorescent
bulbs in working order.(With electronic ballest).
Supply and installation of watertight bracket lamp
508 S-150 (Bulk head) with 15 W CFL bulb (CFL bulb shall be 5 nr 1,582.00 1,718.00
stars rated or greater) in working order.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Supply and installation of watertight bracket lamp
509 S-151 (Bulk head) with 20 W CFL bulb (CFL bulb shall be 5 nr 1,636.00 1,777.00
stars rated or greater) in working order.
Supply and installation of 10W LED floodlight with IP
510 S-152 65 rating or greater in working order. (shall have nr 1,519.00 1,650.00
minimum two year warranty period).
511 S-153 65 rating or greater in working order. (Shall have nr 3,852.00 4,184.00
Supply and installation of recessed (ceiling embedded)

515 S-157 nr 1,311.00 1,424.00
type 6W LED panel lamp fitting in working order.(Shall
have minimum two year warranty period).

516 S-158 nr 1,582.00 1,718.00
type 12W LED panel lamp fitting in working
order.(Shall have minimum two year warranty period).

517 S-159 nr 1,907.00 2,072.00

518 S-160 nr 2,558.00 2,779.00
Supply and installation of surface mounted type 6W

519 S-161 nr 1,419.00 1,541.00
LED panel lamp fitting in to working order. (Shall have

520 S-162 LED panel lamp fitting in to working order. (Shall have nr 1,745.00 1,895.00

521 S-163 nr 2,016.00 2,190.00

522 S-164 nr 3,209.00 3,486.00

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
32A single Phase Distribution Boards
(Plastic Enclouser)
Supply and installation of 6 way single phase
distribution board in surface mounted type plastic
523 S-165 nr 12,660.00 13,751.00
enclosure including 32 A 2P MCB , 40A 2P RCD
(30mA) , 02 nos. single pole M.C.B s.
524 S-166 nr 14,863.00 16,145.00
525 S-167 nr 17,230.00 18,715.00
526 S-168 nr 19,434.00 21,109.00
527 S-169 nr 21,746.00 23,621.00
528 S-170 nr 25,307.00 27,489.00
529 S-171 nr 26,641.00 28,938.00

530 S-172 distribution board in surface mounted type powder nr 16,133.00 17,524.00
coated metal enclosure including 32 A 2P MCB , 40A
2P RCD (30mA) , 02 nos. single pole M.C.B s.




RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.



537 S-179 nr 16,525.00 17,949.00
538 S-180 nr 18,729.00 20,343.00
539 S-181 nr 21,095.00 22,914.00
540 S-182 nr 23,299.00 25,308.00
541 S-183 nr 25,611.00 27,819.00
enclosure including 63 A 2P MCB , 63 2P RCD (30mA)
, 10 nos. single pole M.C.B s.
542 S-184 nr 29,172.00 31,687.00
543 S-185 nr 30,485.00 33,113.00


RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.



distribution board in surface mounted type powder
548 S-190 nr 30,386.00 33,006.00
coated metal enclosure including 63 A 2P MCB , 63 2P
RCD (30mA) , 10 nos. single pole M.C.B s.


Other Distribution boards

Supply and installation of of 40A 2P MCB in plastic
551 S-193 nr 4,075.00 4,426.00
enclosure.
552 S-194 nr 6,147.00 6,677.00
enclosure.
553 S-195 nr 10,210.00 11,090.00
enclosure.
554 S-196 nr 13,086.00 14,214.00
enclosure.
Supply and installation of of 100 A, 4P, MCCB in a
555 S-197 nr 28,351.00 30,795.00
surface mounted metal enclosure.
Supply and installation of 28 way (14 x 2) 2 row metal
enclosure including 2 nos. of 40A 2P MCB,2 nos. of
556 S-198 40A/ 30mA 2P RCD, 20 nos. of 1P MCB and all other nr 46,563.00 50,577.00
necessary items including internal wiring in working
order.
enclosure including 2 nos. of 63A 2P MCB, 2 nos. of
557 S-199 63A 30mA 2P RCD, 20 nos. of 1P MCB and all other nr 54,293.00 58,973.00
order.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
enclosure including 1 no. of 40A 2P MCB, 1 no. of
558 S-200 40A/ 30mA 2P RCD, 15 nos. of 1P MCB and all other nr 35,941.00 39,040.00
order.
enclosure including 1 no. of 63A 2P MCB, 1 no. of
559 S-201 63A 30mA 2P RCD, 20 nos. of 1P MCB and all other nr 43,141.00 46,860.00
order.
enclosure including 1 no. of 40A 4P MCB, 3 nos. of
560 S-202 40A 2P MCB, 3 nos. of 40A/ 30mA 2P RCD, 18 nos. nr 63,177.00 68,623.00
of 1P MCB and all other necessary items including
internal wiring in working order.
enclosure including 1 no. of 63A 4P MCB ,3 nos. of
561 S-203 63A 2P MCB, 3 nos. of 63A 30mA 2P RCD, 18 nos. nr 76,198.00 82,767.00
internal wiring.
enclosure including 1 no. of 40A 4P MCB ,3 nos. of
562 S-204 32A 2P MCB, 3 nos. of 40A/ 30mA 2P RCD, 30 nos. nr 75,044.00 81,513.00
internal wiring.
enclosure including 1 no. of 63A 4P MCB, 3 nos. of
563 S-205 63A 2P MCB, 3 nos. of 63A 30mA 2P RCD, 30 nos. nr 93,250.00 101,289.00
internal wiring.
Supply of 1 number of 1P MCB.
564 S-206 nr 656.00 712.00
(6A,10A,16A,20A,25A,32A)
565 S-207 nr 1,722.00 1,870.00
(6A,10A,16A,20A,25A,32A)
566 S-208 Supply of 1 number of 40A 2P MCB nr 1,903.00 2,067.00
567 S-209 Supply of 1 number of 63A 2P MCB nr 3,976.00 4,319.00
568 S-210 nr 3,081.00 3,346.00
(6A,10A,16A,20A,25A,32A).
569 S-211 Supply of 1 number of 40A 3P MCB. nr 3,449.00 3,746.00
570 S-212 Supply of 1 number of 63A 3P MCB. nr 6,227.00 6,763.00
Installation of Surge Protector.

Supply and installation of 20kA , 385V, 2P surge
protector and 2 nos. of 32A 10kA 1P MCB in a
571 S-213 nr 43,976.00 47,767.00
300X300X150mm metal enclouser and completed with
Supply and installation of 20kA, 385V, 4P surge

572 S-214 protector and 4 nos. of 32A 10kA 1P MCB in a nr 47,266.00 51,340.00
300X300X150mm metal enclouser and completed with

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Installation of MCB type change over
Supply and installation of 40A 2P MCB type
573 S-215 changeover in powder coated metal enclouser in nr 4,332.00 4,706.00
working order.
working order.
working order.
working order.
Installation of Fans
Supply and installation of of type 1( complied with SLS
814) ceiling fan 1400mm dia. complete with 5 speed
577 S-219 humfree (electrical switch size 85X85mm) regulator, nr 11,561.00 12,558.00
safety switch and safety wire in working order -
Excluding Wiring .
Supply and installation of type 1 (approved by the
engineer) wall fan with speed regulator in working order-
578 S-220 nr 15,260.00 16,575.00
excluding wiring. ( Prime cost- Rs.12120.00 *
Excluding VAT)
engineer)of 200mm dia. exhaust fan with auto shutter in
579 S-221 nr 10,634.00 11,550.00
working order -excluding wiring. ( Prime Cost -
Rs.7676.00 * Excluding VAT)
Supply and installation of of type 1 (approved by the
engineer) 300mm dia. exhaust fan with auto shutter in
580 S-222 nr 13,680.00 14,859.00
working order -excluding wiring. ( Prime Cost - Rs.
10302.00 * Excluding VAT)
581 S-223 engineer) Orbit fan in working order -excluding wiring. nr 19,946.00 21,666.00
( Prime Cost- 16160.00* Excluding VAT)
Supply and installation of of type 2 (approved by the

582 S-224 engineer) ceiling fan 1400mm dia. complete with 5 nr 7,994.00 8,684.00
speed humfree (electrical switch size 85X85mm)
regulator in working order - Excluding Wiring .
engineer) wall fan with speed regulator in working
583 S-225 nr 7,438.00 8,079.00
order- excluding wiring. ( Prime cost- Rs.5377.00 *
Excluding VAT)
584 S-226 nr 5,906.00 6,415.00
working order -excluding wiring. ( Prime Cost -
Rs.3600.00 * Excluding VAT)

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
585 S-227 nr 7,154.00 7,770.00
working order -excluding wiring. ( Prime Cost - Rs.
4675.00 * Excluding VAT)

586 S-228 nr 8,252.00 8,963.00
engineer) Orbit fan in working order -excluding wiring.
( Prime Cost-RS. 6078.00* Excluding VAT)

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION T - FLOOR / WALL /

CEILING FINISHES
FLOOR FINISHES
Cement Sand Screed
Floor rendering with 1:3 cement and sand, normal
587 T-001 cement floated surface with expansion joints filled with m2 1,043.00 1,132.00
1:2 bitumen sand.( Rate including for curing)
Floor rendering with 1:3 cement and sand approved
588 T-002 coloured surface with expansion joints filled with 1:2 m2 1,255.00 1,363.00
bitumen and sand. (Rate including for curing)
62mm thick floor paved with brick, and rendering 1:3
cement , finishing smooth with gray cement floating
589 T-003 with expansion joints filled in 1:2 bitumen and sand. m2 3,322.00 3,608.00
(Rate including for brick paved with 2:5 lime mortar and
curing)
62mm thick floor paved with brick, and rendering 1:3
cement , finishing smooth with gray cement floating
590 T-004 with expansion joints filled in 1:2 bitumen and sand. m2 2,591.00 2,815.00
(Rate including for brick paved with 2:5 lime mortar
and curing). Bricks available at site.
100mm high skirting in cement and sand 1:3 projected
591 T-005 or flush to walls finished smooth with gray cement m 626.00 680.00
floating including forming groove.
100mm high skirting in cement and sand 1:3 projected
592 T-006 or flush to walls finished smooth with coloured cement m 660.00 716.00
including forming groove.
Extra over, for waxing and polishing coloured cement
593 T-007 m2 232.00 252.00
floor .
Concrete
Floor concrete with 1:2 1/2:5(25mm) 75mm thick, 1:3

normal cement and sand rendering finished smooth with
594 T-008 expansion joints filled with 1:2 bitumen and sand. Rate m2 2,461.00 2,673.00
including for curing, compacting ground and laying
polythene sheets under the concrete.
loor concrete with 1:2 1/2:5(25mm) 62mm thick, 1:3

normal cement and sand rendering finished smooth with
595 T-009 expansion joints filled with 1:2 bitumen and sand. Rate m2 2,024.00 2,198.00
including for curing, compacting ground and laying
polythene sheets under the concrete.
Floor concrete with 1:2 1/2:5(25mm) 75mm thick with

expansion joints filled with 1:2 bitumen and sand rate
596 T-010 m2 1,418.00 1,540.00
including for the curing, compacting ground and laying
polythene sheet under the concrete.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Floor concrete with 1:2 1/2:5(25mm) 62mm thick with
expansion joints filled with 1:2 bitumen and sand rate
597 T-011 m2 981.00 1,065.00
including for the curing, compacting ground and laying
polythene sheet under the concrete.
GRANITE/ CERAMIC/ CLAY,

TERAZZO/TILES, MOSAIC/ WOOD
BLOCKS, FARQUET FLOORING,
CONCRETE SLABS
Ceramic Tiles
Floor paving with approved pattern and colour ceramic
floor tiles on 1:3 cement mortar, joints filled with tile
598 T-012 m2 1,181.00 1,283.00
grout, to match the colour of tiles and cleaning. (Cost of
tile is not included)
Floor paved with approved pattern and colour floor

tiles (homogeneous /porcelain) with tile mortar on 1:3
599 T-013 m2 1,390.00 1,510.00
cement mortar, joints filled with tile grout to match the
colour of tiles and cleaning. (Tile rate not included)
100mm high tile skirting approved pattern and colour

ceramic floor tiles on 1:3 cement mortar, joints filled
600 T-014 m 364.00 396.00
with tile grout to match the colour of tiles and cleaning.
(Cost of tile is not included)
100mm high tile skirting approved pattern and colour
floor tiles (homogeneous / porcelain) on 1:3 tile mortar,
601 T-015 m 385.00 419.00
joints filled with tile grout to match the colour of tiles
and cleaning. (Tile rate not included)
WALL AND CEILING FINISHES
PLASTERED / RENDERED / ROUGH CAST

COATING , MINERALS COATINGS,
SPRAYED OR SPECIAL WORK, PLASTER
ROAD, TERRAZZO . GRANO
Walls
1:1:5 cement, lime and sand plaster reveals 35mm to
602 T-016 m 363.00 394.00
150mm wide finished smooth with lime putty.
1:1:5 cement, lime and sand plaster to reveals 35mm to
603 T-017 m 293.00 318.00
150mm wide finished semi-rough.
16mm thick cement and sand 1:5 plaster to reveals
604 T-017B 35mm to 150mm wide finished semi-rough with wooden m 290.00 315.00
float.
16mm thick 1:1:5 cement, lime and sand plastering to
605 T-018 m2 1,071.00 1,163.00
walls finished smooth with lime putty.
16mm thick cement, lime and sand 1:1:5 plaster finished
606 T-019 m2 861.00 935.00
semi-rough with wooden float.
Plinth plaster 12mm thick in 1:3 cement and sand
607 T-020 m2 871.00 946.00
finished smooth with gray cement floating.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Plinth plaster 12mm thick in 1:3 cement and sand
608 T-021 m2 1,084.00 1,177.00
finished smooth with coloured cement floating.
Cement and sand 1:3 plaster finished smooth with lime
609 T-022 putty on exposed faces of concrete surfaces and soffits, m2 1,591.00 1,728.00
10mm thick.
16mm thick cement and sand 1:5 plaster finished semi-
610 T-023 m2 846.00 919.00
rough with wooden float.
Rendering cement and sand 1:3, 20mm thick, finished
611 T-024 m2 1,278.00 1,388.00
smooth with grey cement floating on walls.
Black board plastering with 1:3 cement and sand
612 T-025 finished smooth with black cement floating including m2 1,667.00 1,811.00
moulding at perimeter 20mm thick.
Tiles glazed of approved pattern and colour with all
specials fixed to walls including raking plaster and
613 T-026 bedding in cement mortar 1:3, joints finished with tile m2 2,856.00 3,103.00
grout to match colour of tiles and cleaning. (Tile rate not
included)

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION U - GLAZING / INFILL
PANELS
GLAZING
614 U-001 Supplying & fixing glass panes 3mm thick, m2 2,541.00 2,760.00
clear/pinhead, rate includes for necessary beadings etc.
Supplying & fixing glass panes 4.6mm clear / pinhead
615 U-002 m2 3,096.00 3,363.00
,rate includes for necessary beadings etc.
SECTION V - PAINTING
Plastered work
Paint emulsion two coats, after preparing and applying
616 V-001 m2 621.00 675.00
one coat of alkali resisting primer to walls.
Paint emulsion, applying one coat after cleaning and
617 V-002 m2 227.00 246.00
preparing surface.
Paint emulsion, applying two coats after cleaning and
618 V-003 m2 433.00 470.00
preparing surface .
Floor paint, applying one coat after cleaning and
619 V-004 m2 416.00 451.00
preparing surface .
Floor paint, applying two coats after cleaning and
620 V-005 m2 973.00 1,057.00
preparing surface .
Paint exterior emulsion, applying one coat after cleaning
621 V-006 m2 229.00 249.00
and preparing on surfaces .
Paint exterior emulsion, applying two coats after
622 V-007 m2 434.00 472.00
cleaning and preparing on surfaces .
Paint exterior emulsion, applying two coats for new
623 V-008 m2 671.00 729.00
walls after applying one coat of primer .
White or colour washing , applying one coat to walls.
624 V-009 m2 31.00 34.00
White or colour washing , applying one coat to walls
625 V-010 m2 73.00 79.00
after patching up and preparing surface.
White or colour washing , applying two coat to walls
626 V-011 after scraping to original plaster and patching up. m2 144.00 157.00
White washing, applying one coat to ceilings and soffit .

627 V-012 m2 84.00 91.00
White washing, applying two coat to ceilings and soffit .
628 V-013 m2 150.00 163.00
Skim coat compound, applying two coats on walls or
629 V-014 soffit, finished smooth. (Prepairing surface for painting) m2 454.00 493.00
Asbestos Cement work

Paint roofing, applying two coats on roof after cleaning .
630 V-015 m2 430.00 467.00
Wood work / Metal Work

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Paint enamel, applying two coats after cleaning and
631 V-016 preparing surface in new wood work (inclusive of one m2 1,038.00 1,127.00
coat of primer).
Paint enamel, applying one coats after cleaning and
632 V-017 m2 435.00 473.00
preparing surface .
Paint enamel, applying two coats after cleaning and
633 V-018 m2 1,017.00 1,105.00
preparing surface .
Polyurethane varnish, applying two coats after sand
634 V-019 m2 551.00 598.00
papering and cleaning surface .
Polyurethane varnish, applying one coat for old wooden
635 V-020 m2 405.00 439.00
surfaces after sand papering and cleaning .
Paint anticorrosive, applying one coat on steel work
636 V-021 m2 487.00 529.00
after removing scales and wire brushing.
Paint anticorrosive, applying two coat on steel work
637 V-022 m2 714.00 776.00
after removing scales and wire brushing.
Paint Zn Phosphate (Yellow/ Black) metal primer, two
638 V-023 coats on steel work after removing scales and wire m2 803.00 872.00
brushing.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION W - DRAINAGE
SYSTEMS
Pipes
Supplying and laying of pvc 110mm diameter (type
639 W-001 400) on walls with pvc brackets, Rawl Plug (Specials m 1,304.00 1,416.00
paid separately)
640 W-002 400) on trenches excluding excavation. (Specials paid m 1,111.00 1,207.00
separately)
641 W-003 400) on walls with pvc brackets, Rawl Plug (Specials m 2,874.00 3,122.00
paid separately)
642 W-004 400) on trenches excluding excavation. (Specials paid m 2,681.00 2,912.00
separately)
643 W-005 Supplying and fixing elbow pvc 110mm. nr 1,396.00 1,517.00
Supplying and fixing, Cleaning eye bend pvc (89D)
644 W-006 nr 1,217.00 1,322.00
110mm.
645 W-007 Supplying and fixing bend PVC 110 for drainage. nr 903.00 981.00
646 W-008 Supplying and fixing Tee, pvc 110mm for drainage. nr 1,758.00 1,910.00
Supplying and fixing 150mm x 150mm PVC gully
647 W-009 including concreting and supplying necessary grating. nr 814.00 884.00
Manholes
Construction of manhole 600mm x 600mm x 600mm
internally complete with cement concrete 1:2:4 (20mm)
in 75mm thick base, 225mm tk.brick walls on top of
base slab and channelling & benching, 1:3 cement and
648 W-010 sand rendered in internal surfaces, 75mm thick RC. nr 21,271.00 23,105.00
cover slab r/f with 10mm tor steel @ 150mm c/c. both
ways, complete with lifting handles. Drawing
No.CPC/CS/11/04/2018/TYPE-MH/01
Construction of manhole 1.05m x 0.675m x 0.60m

internally complete with cement concrete 1:2:4(20mm)
in 75mm thick base, 225mm tk.brick walls on top of
base slab and channelling and benching, 1:3 cement and
649 W-011 sand rendered in internal surfaces, 75mm thick R.C.C. nr 32,737.00 35,560.00
cover slab r/f with 10mm tor steel @ 150mm c/c. both
ways, complete with lifting handles. Drawing
No.CPC/CS/11/04/2018/TYPE-MH/02
Construction of manhole 1.05m x 0.675m internally

brick walls 225mm , 1:3 cement and sand rendered in
650 W-012 nr 8,424.00 9,151.00
internal surfaces extra over each additional 0.3 m depth.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Construction of manhole 600mm x 600mm internally
complete with brick walls 1:3 cement and sand
651 W-013 nr 6,372.00 6,921.00
rendered in internal surfaces, extra over for each
additional 0.3m depth.
Soakage Pit
Construction of 1.2m diameter internal fully built type
soakage pit, built up 225mm thick brick work in 1:8
cement ,sand mortar invert depth from ground level
3.0m,on 225mm x 150mm ring beam 1:2:4(20mm)
concrete mix, including 1:3 cement,sand plaster
652 W-014 finished smooth with neat gray cement (0.9m invert nr 150,109.00 163,050.00
depth only) & 100mm high 1:2:4(20mm ) concrete ring
pad above ground level, complete with 75mm thick
RCC cover slab with lifting handle.All as per detail
drawing No.CPC/CS/11/04/2018/TYPE-SP/03.
Construction of 1.2m diameter internal semi built type

soakage pit, built up 225mm thick brick work in 1:8
cement and sand mortar invert depth from ground level
0.90m, on 225mm x 150mm ring beam 1:2:4(20mm)
concrete mix, including 1:3 cement and sand plaster
653 W-015 finished smooth with neat gray cement & 100mm high nr 63,820.00 69,322.00
1:2:4(20mm ) concrete ring pad above ground level,
complete with 75mm thick RCC cover slab with lifting
handle. All as per detail drawing
No.CPC/CS/11/04/2018/TYPE-SP/04
Construction of 1.8m diameter internal fully built type
soakage pit , built up 225mm thick brick work in 1:8
cement ,sand mortar invert depth from ground level
3.0m, on 225mm x 150mm ring beam 1:2:4(20mm)
concrete mix, including 1:3 cement and sand plaster
654 W-016 finished smooth with neat gray cement (0.9m invert nr 214,834.00 233,354.00
depth only) & 100mm high 1:2:4(20mm ) concrete ring
pad above ground level, complete with 75mm thick
RCC cover slab with lifting handle. All as per detail
drawing No.CPC/CS/11/04/2018/TYPE-SP/05
Septic tank
Construction of septic tank for 30 persons. as per detail
drawing No. CPC/CS/11/04/2018/TYPE-SEPT/01-(i)
655 W-017 nr 178,847.00 194,265.00
and CPC/CS/11/04/2018/TYPE-SEPT/01-(ii)

drawing, extra over for invert depth exceeding up to
656 W-018 nr 18,473.00 20,066.00
1800mm, per each additional 0.3 m.

657 W-019 nr 215,847.00 234,454.00

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
658 W-020 nr 21,256.00 23,089.00
Construction of septic tank for 100 persons.as per detail

659 W-021 nr 284,934.00 309,497.00

660 W-022 nr 26,350.00 28,622.00
SPECIAL ITEM
Supplying and laying type 400 pvc 110mm for sewer
line in medium soil, joints embedded in 1:3:6(40mm)
661 W-023 concrete including necessary excavation, back filling, m 1,272.00 1,382.00
and compaction, invert depth up to 600mm.

line in medium soil, joints embedded in 1:3:6 (40mm)
and compaction invert depth up to 600mm to 900mm.

and compaction invert depth up to 600mm.

and compaction invert depth to 600mm to 900mm.
Shallow drains in floors 75mm diameter in cement

665 W-027 concrete 1:2:4(20mm), 75mm thick in bottom and sides m 1,886.00 2,048.00
including cement and sand rendering.

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
SECTION X - EXTERNAL
WORK
PAVIOR
Paving
Paving interlock blocks (strength 15N/mm2) rough,
gray colour nominal thickness 80mm with quarry dust
666 X-001 bedding including compacting and levelling (Earth m2 2,583.00 2,806.00
levelling and compacting measured seperatly)


colour nominal thickness 80mm with quarry dust
668 X-003 m2 3,155.00 3,427.00
bedding including compacting and levelling (Earth
MISCELLANEOUS / GENERAL
Turfing
Cutting turf sods, loading to hand carts and transporting
up to 30 m, laying and watering for 30days. (Royalty for
670 X-005 m2 397.00 432.00
turf sods, and transport beyond 30m paid separately)
Preparing a filter layer behind the retaining wall using

4" dia. perforated T600 PVC pipe, geo textile , 3/4"
metal packing and river sand (Waterproofing and
671 X-005B protetive layer to be paid separately). All as per the m 3,830.00 4,160.00
detailed drawing No.CPC/CS/11/04/2017/Type-ST/04
Fencing
Fence Barbed wire , 7strands 14 BWG with 4 points at
75mm crs and R.C.C posts 1:1 1/2:3 (20mm) concrete
1.70m high and section 150mm x 150mm at bottom and
100mm x 100mm at top, at 2.4m c/c , r/f with 4 nos
6mm dia. MS rods with 14BWG wire stirrups at 150mm
672 X-006 crs. Rate to include for excavation,1:3:6(40mm) cement m 2,176.00 2,363.00
concrete foundations to all posts and providing
straightening bolts with washers and nuts.All as per
detail drawing No .CPC/CS/11/04/2017/Type-ST/05

RATE FOR
RATE FOR
SE. ITEM TCE
NO NO. BELLOW
3M/Rs.
3M/Rs.
Fence Barbed wire, 10 strands 14 BWG with 4 points at
75mm crs and R.C.C posts 1:1 1/2:3 (20mm) concrete
2.25m high and section 150mm x 150mm at bottom and
100mm x 100mm at top, at 2.4m c/c, r/f with 4 nos 6mm
dia. MS rods with 14BWG wire stirrups at 150mm crs.
673 X-007 Rate to include for excavation,1:3:6(40mm) cement m 2,666.00 2,896.00
concrete foundations to all posts and providing
straightening bolts with washers and nuts. All as per
Special Supports extra over fencing

Fence posts intermediate, or struts Casting & errecting
in cement concrete 1:1 1/2:3(20mm) r/f with 4 nos 6mm
dia. MS rods and 14BWG wire stirrups at 150crs, 1.7m
high and section 150mm x 150mm at bottom and
674 X-008 100mm x 100mm at top, as per detail drawing including nr 3,888.00 4,223.00
fixing with 1:3:6 concrete, excavation etc.All as per
Fence posts intermediate, or struts Casting & errecting

in cement concrete 1:1 1/2:3(20mm) r/f with 4 nos 6mm
dia. MS rods and 14BWG wire stirrups at 150crs, 2.25m
high and section 150mm x 150mm at bottom and
675 X-009 100mm x 100mm top, as per detail drawing including nr 4,586.00 4,981.00
fixing with 1:3:6 concrete, excavation etc.All as per

Table 01 : Manual Transport at Material for 100m based on Mass -2021
Mannual Transport charges for

Density Kg/m3 100 m per Kg Rs.
Material
*
Gradient
Gradient up to 10% above
10%
Bricks 1750
Metal /Rubbel 1600
0.58 0.70
Concrete Block 1800
Sand 1600
Steel 7850
Timber 750
Asbestos sheet 1900 1.35 1.70
Cement 1440
Lime 640
* Distance measured is the shortest walking distance

* Minumum Length of Gradient above 10% should be 30m
Density Kg/m3 = Mass (Kg)

Volume (m3)

TABLE 02
MATERIAL TESTING RATES -2021
ITEM APPROVED RATE

SE. NO. Test
NO. (Rs.)
Soil Testing
1 S1 Particle Size Distribution Test 3,250.00
2 S2 Field Density Test 3,500.00
3 S3 Consolidation Test 15,400.00
4 S4 Direct Shear Test 11,300.00
5 S5 Hand Auger Investigation/meter length 1,600.00
6 S6 Atterbergs Limit Test 4,250.00
7 S7 Moisture Content Test 950.00
8 S8 Standard Compaction Test(Proctor) 5,850.00
9 Mackintosh Probe Test

S9 5,000.00 / 4.8m
Depth beyond 4.8m up to 7.2m 1,600.00 /m depth
9.1
9.2
Beyond 7.2m Depth 2,100.00 /m depth
Mobilization Charge :-
9.3 From 5km to 30km 5,500.00
9.4 From 30km to 100km 10,500.00
10 S10 Sieve Analysis (Soil) 3,250.00
11 S11 Califonia Bearing Ratio of Soil (CBR) 4,900.00
12 S12 DCP 5,650.00
13 S13 Modified Compaction Test 5,250.00
Aggregate test
14 A1 Aggregate Gradation Test 3,150.00
15 A2 Aggregate Flakiness Index Test 3,050.00
16 A3 Aggregate Elongation Test 2,650.00
17 A4 Sieve Analysis (ABC) 3,150.00
18 A5 Aggregate Impact Value 3,180.00
19 A6 Loss Angeles Abrasion Value 5,160.00
Concrete test
20 C1 Compressive Strength of Concrete 1,350.00 per 3 cubs

20.1 For additional cube 450.00

ITEM APPROVED RATE
SE. NO. Test
NO. (Rs.)
21 C2 Concrete Cover & R/F Check 5,600.00

22 C3 Rebound Hammer Test 1,600.00
23 C4 Slump Cone Test 800.00
24 C5 Concrete Mix Design 27,700.00
25 C6 Cement Tests ( Setting Time) 1,850.00
26 C7 Compressive Strength of Interlocking Test 1,000.00
Burnt Clay Brick
27 B1 Compressive Strength of Burnt Clay Brick 1,000.00
28 B2 Water absorption of Burnt Clay Brick 1,000.00
29 B3 Dimension Checking of Burnt Clay Brick 420.00
Other Test
30 O1 Powder Coating Thickness Test 1,400.00
31 O2 Hardness Test 3,150.00
32 O3 Measurement Check(using micro meter 825.00
& Vernier Caliper)
33 O4 M/S and T/S Steel bars Weight Check /3 bar 1,130.00

33.1 for additional bar 450.00
34 O5 Extraction Gradation Asphalt 5,050.00
35 O6 Asphalt/Concrete Core Cutting 3,360.00
*** All the above rates are Excluded the cost of Transport.

HIGHWAY SCHEDULE OF RATES
2021
Provincial Road Development Authority
Central Province
CONTENTS
HIGHWAY SCHEDULE OF RATES
Page
- i to xv
GENERAL NOTES
- TRANSPORT -70 to 72
SECTION 1
- EXCAVATION ROADWAY AND -73 to 74
SECTION 2 FOUNDATION EXCAVATION
- AGGREGATE / RUBBLE AGGREGATE / -75

SECTION 3 RUBBLE INCLUDING LOADING
- EARTH FILLING AND COMPACTION -76

SECTION 4
- RUBBLE PITCHING / PAVING -76
SECTION 5
- AGGREGATE SPREADING & ROLLING -77 to 78
SECTION 6 AGGREGATE SPREADING AND
COMPACTION
- ROAD SURFACE TREATMENT -79 to 81
SECTION 7
- ROAD MAINTENANCE -82
SECTION 8
- ROAD SIDE DRAINAGE SYSTEM -83
SECTION 9
- BRIDGES AND CULVERTS -84 to 89
SECTION 10
- ROAD FURNITURE ITEMS -90
SECTION 11
- NOTICE BOARDS AND ROAD SIGNS -91
SECTION 12
- MISCELLANEOUS -92 to 96
SECTION 13
- SURVEY & DAY WORKS -97
SECTION 14
I
Highways Schedule of Rates – 2021
Provincial Road Development Authority
Central Province
General Notes
This rate schedule is based on basic rate approved on 03.12.2020
01 Highways schedule of Rates (HSR) becomes operative from 01.01.2021
02 This Highways Schedule of Rates is prepared to use for works under the preview
of Provincial Road Development of Central Provincial Council Road sector.
03 In case, the resources are available at lesser rates depending on area and locality,
the Engineer shall use such rates in the BOQ for the preparation of Estimates
providing reasons.
04 Work has to be carried out as per (i) Slandered Specifications for Construction &
Maintenance of Roads and Bridge (S.S.C.M), issued by the Department published
by Road Development Authority – Ministry of Highways – Sri Lanka in 1989.
05 The description of all items in the bills shall briefly conform to that in the relevant
items appearing in this schedule so as to avoid any ambiguity. Control of material
and measuring & paying shall be carried out as per S.S.C.M. 104 to 106.6 However
provision for control of traffic and safety measures for the road users are not
included under such items rate shall be provided separately and paid on approved
S.S.R or on closely monitored work.
06 Quality Materials only shall be used in any works (S.S.C.M.1700).
07 Cement concrete pre-cast product to be brought from approved agencies.

Approved qualities of cement according to the standers can only be used.
08 Certain items like extensive patching for maintenance etc. requires the prior
approval from CE. /General Manager.
I
09 Special schedule of rates have to be approved by the General Manager Road for
item that do not appear in this Highway Schedule of Rates.
10 Materials available / recovered during execution of works:
All suitable earth, rock, steel or precast material and components available or
recovered from road excavation or demolition works shall be utilized in
construction work with the approval of the Chief Engineer and surplus disposes
as directed. In the case of bridge reconstruction works all bridge components such
as steel girders, deck plates, and reinforcement etc., which are dismantled, shall be
recovered and repaired for re use, these items should be taken to an inventory by
the Executive Engineer and kept stock under good care for reuse.
In the cause of rock blasting Material should be piled and taken to an inventory By
the Executive Engineer before authorizing for payments.
11 Transport
11.1 The rates for “transport” include all modes of transport up to maximum distance of
the stipulated range.
11.2 The most economical mode of transport shall always be adopted in transporting
materials. The rate of payment for transport shall be made under any relevant item
selected from code. T1-001 to T1-003b irrespective of the type of vehicles is used
11.3 The rates for transport including up to the maximum distance stipulated.
11.4 The rate for transport steel and cement in shall always be paid separately unless
otherwise directed.
11.5 Transport of aggregate, soil, Emulsion and premix materials shall always be paid
separately unless otherwise directed.
11.6 Rate for rubble transport up to 3 m shall be selected from item code T1-002 to T1-
003b supported with justifiable reasons.
II
12 Excavation (S.S.C.M. 301-303)
12.1 Manual rates:
The rates given in this schedule if not otherwise stated are intended for manual
excavation
12.2 The rates are included for excavation and loading or depositing up to 30 meters.
Transport of excavated material more than 30 meters shall always be paid
separately unless otherwise directed. In case of foundation excavation for structure,
backfilling and compaction to be considered separately unless otherwise specified.
12.3 Additional excavation required for working space shall be decide by the Engineer
and shall be paid at the same rate applicable to the item.
12.4 Soil is generally classified as in Slandered Specifications. (S.S.C.M. 30012.
12.5 Similarly for Roadway Excavation with quantities more than 300 cu.m, rates given
under item codes E1-027, E1-028 and E1-029 shall be adopted. When deviation
from above rates in necessary, -payments shall be made on approved S.S.RR Based
on actual site records (machine hours) or on work studies carried out under close
supervision by the Engineer, after obtaining of the Technical Committee.
12.6 The rates include for excavation and loading or depositing up 25 meters. Transport
of excavated material more than 25 meters shall always be paid separately unless
otherwise directed. In case of foundation excavation for structure, backfilling and
compaction to be considered separately unless otherwise specified.
12.7 Construction of cofferdams that are necessary shall be paid separately. (S.S.C.M.
3002.6) Rates under items ST1-018, ST1-019, & ST1-020 are not applicable for
bridge construction work. For bridge works, it shall be payable on SSRR based on
closely monitored work studies or on day works at HSR/ machine hours,
depending on the site condition.
12.8 De-watering necessary for cofferdams shall be paid separately.(S.S.C.M.3002. (6))
12.9 Rates under Items E1-001 to E1-019 are not applicable for the excavation for
foundation of bridge structure. Payment for such excavation shall be made on
approved S.S.RR based on closely monitored work studies or on day works at
HSR/ machine hours, depending on the site conditions.
III
12.10 Trench excavation for utility services and reinstatement shall be according to
S.S.C.M. 305 and shall be read in conjunction with the procedure to be followed by
agencies when trenching highways. Under no circumstances pedestrians and traffic
using the road shall be allowed to suffer or inconvenienced due to trenching work.
Adequate notice have to be given to the public necessary safety precautions have to
be taken in advance.
a. Ordinary Soil – Sand, Loose Soil

b. Medium soil – Clay, Gravel
c. Hard soil – Stiff Clay/Cabook etc/
d. Soft Rock – Weathered Rock/Sand Stone etc.
e. Hard Rock – Igneous/Metamorphic/Sedimentary
f. Marsh Material – Peat etc.
Note: - Special Schedule of Rate to be prepared for item (f).
13 Aggregate /rubble (Including, Loading & Pilling)
13.1 Except where otherwise stated, the rates include preparing depots, loading and
pilling
13.2 The rates for items Bo-302 to BO- 313 include the cost of blasting materials.
13.3 In exceptional cases such as limestone, “dug out” aggregate, special rates for items
BO shall be approved by the General Manager.
13.4 Transport of aggregate and rubble not included in the rates shall be paid
separately.
13.5 Blasting operations shall be carried out as recommended in S.S.C.M. 306 and all
works in blasting operations shall conform to the guidelines given in the National
Environmental Act. No. 47 of 1980 and any subsequent amended
13.6 Prior approval shall be obtained from the Provincial General Manager for the use
of 19 mm hand broken aggregate.
IV
14 Earth filling & compaction (S.S.C.M. 304, 400 & 600)
14.1 Approved Soil that is pilled shall be spread, watered and well compacted by rolling
as per Standard Specifications.
14.2 The rates for earth compaction include the cost of watering.
14.3 Rates given for the item EW1-003, EW1-004, EW1-005, EW1-006, EW1-007,
EW1-008 and EW1-009 on loose volume are for the work where the % density is
not specified. If the rates to be deiced on compacted volume basis, the rates for
loose volume shall be adjusted by multiplying the specified factor corresponding to
the required % density by the factor given in table below.
% Density Factor
1. For standard density not less than 95% 1.35
2. For standard density not less than 100% 1.42
14.4 For rates another density, S.S.R should be approved by the

Provincial General Manager.
14.5 Transport of water beyond 25 shall be paid separately
14.6
(i) The normal output of earth compaction per day will be 66 Cubic Meters using 8-10
ton Road Roller
(ii) For earth work in widening of existing roads where the average width is less than
15 meters, the output of earth compaction using 8-10 ton Road Roller shall be
considered as 50 Cubic Meters per day.
14.7 Use of small compaction equipment shall be allowed only if the space is restricted
for operating 10 ton Road roller or equipment.
15 Rubble paving (rip rap protection S.S.C.M. 804)
15.1 P1-001 to P1-004 does not include the cost of rubble, which shall be paid for
separately. The coverage of paving is as follows.
i. For pitch paving 225mm thick 026 cu.m of rubble per square Meter
V
ii. For pitch paving 150mm thick 017 cu.m of rubble per square Meter
iii. For flat paving 225mm thick 0.21 cu.m rubble per square Meter
iv. For flat paving 150mm thick 0.15 cu.m rubble per square Meter
15.2 Rubble/rip rap paving shall be carried out to avoid damages by watercourses, slip,
and slides to road embankments. Action shall be taken to include this item to
routine/periodic maintenance flood damage items.
16 Aggregate Compaction (S.S.C.M. 403-408)
16.1 The normal coverage areas shall be as follows:
(i) For paved roads scarified for full width and for strip metaling 14.5 to 19.7 sq.m
shall be compacted with 1 cu.m of new 50mm aggregate.
(ii) For construction of new bases and for edge correction 100sq.m shall be compacted
with 8.8-10.0 cu.m of new 50mm aggregate spread in two layers to 100mm loose
thickness.
16.2 Edge correction shall be 0.6m (approx) in width and edge strengthening shall be
1.2m (approx) in width using 100, 50, & 19 mm aggregate conforming to S.S.C.M
1103.
16.3 Strip metaling shall be considered only when the surface section to be metaled is in
narrow strips less than 1.2m in width.
16.4 For construction of new bases, where aggregate compaction of the 19mm and
50mm is required 1.0 cu.m of 19 mm aggregate is adequate for compacting with 10
cu.m of 50mm.
16.5 The normal quantities of aggregate that shall be compacted per day as follows:
(i) For full width of paved road including scarifying and/or hand picking the surface
will be 12.75cu.m of new aggregate per day (8 hours).
VI
(ii) For construction of new bases, 23.5 cu.m of new aggregate per day (8 hours).
(iii) For strip or edge correction including loading scarifying and/ or handpicking the
surface, 9.90 cu.m per day (8 hours).
16.6 The average rate of traveling of Oil/Diesel Roller is 20 Km per day.
16.7 Metal Construction
(i) The rates for items from R1 – to R1 – include the necessary re transport of metal
and no further re transport could be paid.
(ii) The rates for metal consolidation include transport of water.
(iii) Certificate of payments for metal involved should be based on metal pile
measurements. .
(iv) For Extensive patching the prior approval of the Chief Engineer should be
obtained maximum quantity involving in normal patching is decided by the deputy
General Manager (Construction). .
(v) The Executive Engineer/Technical Officer will carry out of physical check of
bitumen issued to contractors.
(vi) For this analysis the grading of the base course for 1 m3 as followed.
No Material Composition
1 [37.50 mm]] 0.20 M3 (20 % of Vol.)
2 25.00 mm 0.20 M3 (20 % of Vol.)
3 18.00 mm 0.20 M3 (20 % of Vol.)
4 12.00 mm 0.20 M3 (20 % of Vol.)

5 Quarry dust mm 0.20 M3 (20 % of Vol.)
For the use at site, prior approval of CE/DD roads should be obtained for
gradation.
VII
Before certifying the payment for the item S/-001 to S/-040 a (section 7) the
technical Officer has to measure that the actual rate of application of bitumen and
the material return to be adjusted, according to rate of application.
The rate for item M1-001, M1-004 and M1-007 to M1-0013 include the necessary
re-transport of aggregate and no further re-transport costs shall be paid.
16.8 The actual scarified area (which is not necessary the bitumen surfaced area) shall be
paid for in item M1-002 & M1-003. Normally 0.3m width (approx.) shall be
reckoned as requiring scarifying for edge correction.
16.9 Tempering and sharpening for scarifies tines are included in the rates for item M1-
003 and shall not be paid for separately.
16.10 Transport of water beyond 25 meters shall be paid separately.
16.11 Before certifying the payment for the item S/-001 to S/-040 a (section 7) the
technical Officer has to measure that the actual rate of application of bitumen and
the material return to be adjusted, according to rate of application. It is the
responsibility of the Technical Officer to maintain the applying rate of bitumen
within the given range.
17 Road side and drainage systems (S.S.C.M 104)
17.1 The rates exclude the cost of loading, unloading and transporting but include
spreading suitably in the vicinity unless otherwise directed.
17.2 Culvert inlets and outlets should be cleaned before and after the rains.
17.3 For clearing choked culvert (item DR1-012) with head room/ diameter less than 1
meter, day works rates shall be adopted.
17.4 Drains should be cleared before commencing any types of surfacing (S.S.C.M 501-
507)
VIII
18 Bridge, Culvert, retaining walls, ECT. (S.S.C.M 1001-1010)
Note;
18.1 Concrete work

Concrete mixers should be used for mixing of all reinforced concrete or concrete
specified by their Grade and in other concrete mixing, exceeding 3 cu.m, unless
otherwise directed. Weigh batch mixers shall be used for all concrete specified on
Grade 25 and above.
(i) The cost of shuttering is not included in the rate, and shall be paid separately.
(ii) The cost of hire charge for concrete mixer is included in the rates for concrete
using mixers.
(iii) Construction of necessary cofferdam, shoring, forming and de-watering shall be

paid separately.
(iv) For all concrete with 19mm aggregate, crusher plant materials shall be used unless
otherwise directed.
18.2 Only sand of approved quality shall be used for cement mix, mortars &
concretes.
18.3 The rate includes the cost of transport up to 30 meters on level ground in the
relevant items. Any vertical transport required in excess of first 1.5 meters upwards
or down wards shall be separately considered.
18.4 Transport of water beyond 25 meters shall be paid separately.

18.5 To obtain the normal mix of cement concrete 1:2:4 19 mm; batching of materials
in the field under average condition will be in the proportions 1:2 ½:4 volumes.
Cement concrete 1:3:6 (37.5 mm) and cement concrete 1:4:8 (50 mm) may
continue to be batched by volume in the specified normal proportions; cement
should be by bags of 50 Kg. and shall deem to be 0.035 cu.m in volume.
18.6 The quantities of the various materials for cement concrete and cement mortars
required to yield an average workable mix shall be as follows.
In items 12 – 15 the cement quantity is exclusive of that required for smoothing
where necessary.
IX
Proportion Cement Aggregate
yield sand
Description [normal mix] or in 50 / Rubble
Unit (cu.m)
No Grade Kg. (cu.m)
1 cement concrete g 40 (19 mm) cu.m 8.26* 0.46* 0.79*
2 cement concrete g 30 (19 mm) cu.m 7.16* 0.48* 0.80*
3 cement concrete g 25 19 mm) cu.m 7.16* 0.50* 0.79*
g 25 (37.5mm+19 37.5=0.62*
cement concrete cu.m 5.86* 0.46*
4 mm )70% 30% 19.0=0.27*
5 cement concrete g 20 (19 mm ) cu.m 6.04* 0.53* 0.79*
6 cement concrete 1:1 ½:3 (19 mm) cu.m 8.12 0.60 0.91
7 cement concrete 1:2:4 (19 mm) cu.m 5.65 0.60 0.90
8 cement concrete 1:2:4 (37.5 mm) cu.m 5.65 0.60 1.00
10 cement concrete 1:3:6 (37.5 mm) cu.m 4.38 0.60 1.00
12 12.5 mm cement
1:2 mix sq.m 0.15 0.013 -
render
13 19.0 mm cement
1:2 mix sq.m 0.23 0.020 -
render
14 12.5 mm cement
1:3 mix sq.m 0.12 0.016 -
render
15 19.0mm
1:3 mix sq.m 0.19 0.024 -
cement render
Random Rubble
16 masonry in
1:6 mix cu.m 0.40 1.10
cement/sand
mortar
The above mix proportion for Grade concrete is given for estimation purposes.
The actual proportion for Grade concrete shall be directed by mix designs at sit
and the rates shall be adjusted with the approval of the Provincial General
Manager.
X
18.7 Ready mixed concrete;
Ready mix concrete shall be used only on the written approval of the General
Manager and for the procumbent of the material government tender procedure
The contractor for ready mix concrete shall be a copious supplier having minimum
of one year experience of supplying ready mix concrete to project acceptable to the
tender board and shall have sufficient & pumping facilities, laboratory facilities for
quality control and qualified staff.
18.8 Wearing surface for R.C.C/ P.C.C. decking (S.S.C.M. 1403)
Generally for 74.5 sq.m of 50mm thick compacted wearing surface, the quantities
of material required will be 3.5 cu.m 19mm to 3.2mm graded aggregate, 2.3cu.m
sand and 381 liters Bitumen and 91 liters of kerosene. If Emulsion is used, the
quantity of material required is 500 liters of Emulsion and 273 liters of water.
18.9 Concrete pipe culvert (S.S.C.M. 1403)
(i) The diameter of pipes indicated refers to the internal diameter.
(ii) The rates include the cost of pipe, collars, rolling up to the distance of 30m
lowering to bed up to 1.8 meter depth, aligning and fixing.
(iii) Excavation and backfilling of trench is not included in the rates unless otherwise
mentioned.
19 Labour, Plant and Materials
19.1 All labour, plant, equipment and materials have to be provided by the contractor.
19.2 The Engineer should maintain performance records of all types of machinery for
future reference.
20 Maintenance of road signs and marking (S.S.C.M. 1501 -1502)
All traffic signs, kerbs, parapets, guardrails, barricading and Km posts should be
painted at least once a year.
XI
21 Quality control work; (S.S.C.M. 1600)
21.1 Special attention should be made to control the alignment, thickness and surface
regulation of pavement layers as per section 1601 of the S.S.C.M.
22 Working rates of HSR are calculated as follows
a. For the projects where the Total Cost Estimate (TCE) is less than or
equal 03 million rupees
 Overheads & profit margin is taken as 26% of the basic rate.
Where,
Item Overhead Type Percentage
No
A Site Overhead 16%
B Profit 10%
Total Overhead & Profit 26%
Table-01
XII
No
1 Supervision of work (wage of work Supervisor) 1.0%

2 Supervision of labour (wage of ganger) 4.0%
3 Tempory works:
a. Access road & maintenance 0.2%
b. Site building for accommodation of part 0.7%
labour
c Control stores building 0.6%
d Fencing and protection 0.3%
e Provision of water, light etc. 0.3%
f Cleaning 0.2%
g. Stacking of material including cement & 0.4%
steel
4 Security for construction sites 0.8%
5 Tools and implements for miscellaneous work 0.9%
6 Setting out according to the drawing 0.5%
a. Providing sample for testing 0.2%
7 Transportation of supervisory staff 1.0%
8 Job office, furniture, Stationery, Suppliers, water, 0.9%
light, etc
9 Wages of job office staff 1.2%
10 Transportation of job office staff 0.4%
11 Bonds of bit performance and fidelity guarantee 0.3%
Providing Insurance of work and workman’s 0.5%
Compensation
12 Interest in capital investment 1.6%
Total 16%
Table-03
 Overheads Rate = Basic Rate + Overheads & Profit Margin
b. For the projects where the Total Cost Estimate (TCE) is over 03 million
rupees
 Separate preliminary bill shall be included (Applicable site overhead
percentages for the preliminary bill shall be taken from table -03)
 Overheads & profit margin is taken as 16% of the basic rate.
XIII
Item
No Overhead Type Percentage
A Site Overhead 6%
B Profit 10%
Total Overhead & Profit 16%
Table-02

No
1 Head office and rent, light, telephone, stationery

suppliers, Furniture, Etc. for same 0.6%
2 Salaries head office manager, Engineer’s, Technical 1.2%
Assistances, Draughtsman, Clerks, Stenos, Typiests,
Minor staff and drivers
3 Transportation and subsistence of head office staff 1.0%
4 Insurance , Interest, and Taxes on business 0.4%
5 Legal expenses and consultancy fees 0.2%
6 Workshop and yard rents, sheds, garages and supplies 2.2%
Salaries of workshop and yard storekeepers, drivers,
7 0.4%
foremen,Mechanics and workmen
Total 6.0%
Table-04
Method of Measurement
I. The Bill of Quantities have been generally prepared in accordance with principles of
the Standard Method of Measurements for Building works in Sri Lanka (SLS 573
1999)
Head transport rates given in Irrigation rate have to be taken for slop angle less
than 20 in hilly areas, when the slop angle exceeds 20o the head transport to be
referred to central provincial price committee report 2020. However, considering
site condition, engineer can decide the necessary Head transport.
XIV
II. A Confidential document and to be used for Central provincial council work only
III. This document to be used for estimation purpose only
IV. Additional should be prepared for any item deviate from the description or not
listed based on Irrigation rate Annalise / work study
SI – British conversion factors
Mass 1Kg 2.204 lb
Length 1m 3.281 ft
1 Cu.ft 0.028 m3
1 Sqrs 9.29 m2
1 cub 2.831 m3
1 sq.ft 0.092 m2
1 lb 0.453 Kg
1 cwt 50.802 Kg
1 gal 4.546 l
23 HSR Analysis is for internal use only. It cannot be produced in Court of law
as reference/ authority and thus is a privilege document.
XV
HIGHWAY SCHEDULE OF RATES-2021
Section 1 - Transport
See Section 1 of General Notes for Selection of Mode of Transport
RATE RATE FOR

SE. ITEM FOR TCE TCE
DESCRIPTION UNIT
NO. NO. ABOVE BELLOW
3M/Rs. 3M/Rs.
Transport of Soil beyond 25m and up to and including100 m by
1 T1-001 Cu.m 539.52 586.03
Any Means (including Loading and Unloading)
2 T1-002 Transport of Sand, Soil and Metal upto 10 Km (Bulk) Cu.m 353.00 444.78
3 T1-003 Transport Sand, Soil and Metal Beyond Every Each 1Km (Bulk) Cu.m 25.80 37.80
Transport beyound 0.5km and up to and including 1.0km by Any

4 T1-003A Cu.m 321.50 349.00
Means.(Excluding Loading)
Transport of each 1km beyon 1.0 to 9.0 km by Any Means
5 T1-003B Cu.m 50.00 54.25
(Excluding Loading)
Transport of Each Subsequent 1km beyond 9km by Any Means
6 T1-003C Cu.m 33.50 36.50
(Excluding Loading)
7 T1-004 Transport of Cement upto 10 Km Bag 8.60 12.60
8 T1-005 Transport of Cement Beyond Every Each 1Km Bag 0.73 1.07
9 T1-006 Transport of Steel Upto 10 Km Kg 0.17 0.25
10 T1-007 Transport of Steel Beyond Every Each 1Km Kg 0.01 0.02
Transport of Premix in Bulk, Excluding Loading other than at
11 T1-009 TonKm 21.90 23.80
Mixing Plant
Transport of Barrels of Bitumen for First 1.0km of Transport
12 T1-010A BrlKm 47.50 51.75
(Excluding Loading and Unloading)
Transport of Barrels of Bitumen for Each Subsequent 1.0km From
13 T1-010B BrlKm 11.90 12.95
1.0km - 9.0km (Excluding Loading and Unloading)
Transport of Barrels of Bitumen for Each Subsequent 1.0km
14 T1-010C BrlKm 8.30 9.05
Beyond 9.0km (Excluding Loading and Unloading)
Transport of empty Barrels of Bitumen for First 1.0km of
15 T1-010E BrlKm 11.90 12.95
Transport (Excluding Loading and Unloading)
Transport of empty Barrels of Bitumen for Each Subsequent 1.0km

16 T1-010F BrlKm 4.65 5.05
From 1.0km - 8.0km (Excluding Loading and Unloading)
Transport of empty Barrels of Bitumen for Each Subsequent 1.0km

17 T1-010G BrlKm 12.00 13.00
Beyond 8.0km (Excluding Loading and Unloading)
18 T1-010H Loading empty barrels of Bitumen Brls 6.75 7.00
19 T1-010J Unloading empty barrels of Bitumen Brls 2.85 2.95
20 T1-010K Cutting & straightening empty barrels of Bitumen Brls 180.00 193.50
21 T1-013 Loading Barrels of Bitumen Inclusive of Rolling upto 25m Brls 36.50 39.75
22 T1-014 Unloading Barrels of Bitumen Inclusive of Rolling and Stacking Brls 15.65 17.00
Transport of Hume Pipes 152mm diameter for 1st 1.0km of

23 T1-015A L.mkm 36.00 39.00
Transport of Hume Pipes 152mm diameter for Each Subsequent
24 T1-015B 1.0km From 1.0 to 8.0km of Transport (Excluding Loading and L.mkm 10.00 10.85
Unloading)
25 T1-015C 1.0km Beyond 8.0km of Transport (Excluding Loading and L.mkm 7.20 7.80
Unloading)
26 T1-018A L.mkm 40.50 44.00

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Unloading)
28 T1-018C 1.0km Beyond 8.0km of Transport (Excluding Loading and L.mkm 8.10 8.80
Unloading)
29 T1-021A L.mkm 54.00 58.50
Unloading)
31 T1-021C 1.0km Beyond 8.0km of Transport(Excluding Loading and L.mkm 10.80 11.75
Unloading)
32 T1-024A L.mkm 81.00 88.00
Transport(Excluding Loading and Unloading)
Transport of Hume Pipes 457mm diameter for Each Subsequeent
33 T1-024B 1.0km From 1.0 to 8.0km of Transport(Excluding Loading and L.mkm 22.55 24.50
Unloading)
Unloading)
35 T1-027A L.mkm 108.00 117.00
Unloading)
Unloading)
38 T1-030A L.mkm 162.00 176.00
Unloading)
Unloading)
41 T1-033A L.mkm 370.50 402.50
Unloading)
Unloading)
44 T1-036 Loading and Unloading 152mm diameter 2.44m Long Hume Pipes No 113.00 122.50

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
49 T1-041 Loading and Unloading 915mm diameter 2.44m Long Hume Pipes No 1,045.00 1,135.00
Loading and Unloading 1220mm diameter 2.44m Long Hume

50 T1-042 No 2,090.00 2,270.00
Pipes
Transport of Recast Kerb Stones (All Types) for Road Works,
51 T1-043 L.mKm 2.25 2.40
Including Loading and Unloading
Transport of Recast Kerb Stones for Bridge Works, Including
52 T1-044 L.mKm 3.35 3.65
Loading and Unloading
Transport of Precast Concrete Handrails, Up Rights and Joints for
53 T1-045 L.mKm 4.90 5.30
Bridge Works, Including Loading and Unloading
Transport of Precast Concrete Slabs 450x450x50 mm for Foot
54 T1-046 L.mKm 5.95 6.50
Walks, Including Loading and Unloading
Transport of Precast Concrete Standard Boundary Markers
55 T1-047 No.km 3.05 3.35
Including Unloading Only
56 T1-048 Transport of Emulsion 100ltr km 1.95 2.10
57 T1-049 Transport of Gabion Mesh 4x1x1 meters No km 1.45 1.60
58 T1- 050 Transporting Road Roller up to 25 km No 7,128.00 7,870.50
59 T1- 050A Additional cost for Transporting Road Roller beyond 25 km km 290.40 320.65
60 T1- 051 Transport of cement 1st km including loading and unloading 1 bags(50kg) 8.43 9.30
61 T1- 051A Transport of cement beyond 1.00 km to 9km by any means 1 bags(50kg) 1.46 1.61
Transport of cement each Subsequent 1.0km beyond 9.0km by any
62 T1- 051B 1 bags(50kg) 1.16 1.28
means
63 T1- 052 Transport of steel 1st km including loading and unloading 50kg 11.91 13.15
64 T1- 052A Transport of steel beyond 1.00 km to 9km by any means 50kg 2.32 2.57
65 T1- 052B Transport of steel each Subsequent 1.0 km to 9.0 km by any means 50kg 1.74 1.92

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Section 2 - ExcavationRoadway and Foundation

Excavation (Including Loading, Unloading, and
Transporting within 25 meters Distance Unless
Otherwise Specified)
66 E1-001 Excavation in Loose Soil (Dry) [SSCM 301.2(IV)] Cu.m 811.00 881.00
67 E1-002 Excavation in Loose Soil (Wet) in Slips [SSCM 301.3(0)] Cu.m 1,000.00 1,085.00
Excavation in Ordinary Soil (Cutting Measurement) [SSCM
68 E1-003 Cu.m 1,190.00 1,290.00
301.2(V)]
Excavation in Ordinary Soil [Vehicle Measurement] [SSCM
69 E1-004 Cu.m 1,045.00 1,135.00
301.2(V)]
Excavation in Medium Soil (Cutting Measurement) [SSCM
70 E1-005 Cu.m 1,565.00 1,700.00
301.2(VI)]
Excavation in Medium Soil (vehical Measurement) [SSCM
71 E1-006 Cu.m 1,330.00 1,445.00
301.2(VII)]
Excavation in Hard Soil (Cutting Measurement) [SSCM
72 E1-007 Cu.m 2,325.00 2,525.00
301.2(VII)]
Excavation in Hard Soil (Vehicle Measurement) [SSCM
73 E1-008 Cu.m 1,975.00 2,145.00
301.2(VII)]
Excavation in Unclassified Soil (Cutting Measurement) [SSCM
74 E1-009 Cu.m 1,695.00 1,840.00
301.2 a(1)]
Excavation in Soft Rock (Cutting Measurement) [SSCM
75 E1-010 Cu.m 2,510.00 2,730.00
301.2(VII)]
Excavation in Mud\Marshy Material (Cutting Measurement)
76 E1-010A Cu.m 1,945.00 2,115.00
[SSCM 301.2(VII)]
Excavation Pit\Trench for Foundation in Ordinary Soil not
Exceeding 1.5m deep, Including Leveling and Ramming Bottom,
77 E1-011 Cu.m 1,565.00 1,700.00
Exc. Material Deposited within 25m or as Directed. [SSCM 301.1-
.3]
Excavation Pit\Trench in Foundation in Medium Soil not
Exceeding 1.5m deep, Including Leveling and Ramming Bottom,
78 E1-012 Cu.m 1,945.00 2,115.00
Exc. Material Deposited within 25m or as Directed. [SSCM 301.1-
.3]
Excavation Pit\Trench in Foundation in Hard Soil not Exceeding

79 E1-013 1.5m deep, Including Leveling and Ramming Bottom, Exc. Cu.m 2,700.00 2,935.00
Material Deposited within 25m or as Directed. [SSCM
Excavation Pit\Trench in Foundation in Unclassified Soil not

80 E1-014 Exceeding 1.5m deep, Including Leveling and Ramming Bottom, Cu.m 2,070.00 2,250.00
Exc. Material Deposited within 25m or as Directed. [SSCM
Excavation Pit\Trench in Foundation in Mud/Marsh not Exceeding

81 E1-015 1.5m deep, Including Leveling and Ramming Bottom, Exc. Cu.m 2,325.00 2,525.00
Material Deposited within 25m or as Directed. [SSCM
82 E1-019 Excavation Soft Rock not Exceeding 1.5m depth [SSCM 301.2(II)] Cu.m 3,080.00 3,345.00
83 E1-021 Piling Available Soil Cu.m 189.00 205.50

84 E1-022 Loading Available Soil to a Tractor or Equivalent Cu.m 249.50 271.00
Excavating Rock Requiring Blasting, for Roadway for Boulders,

85 E1-023 Cu.m 1,050.71 1,140.00
Excluding Dozing Away [SSCM 301.2(III) & 306.1-306.4]

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
86 E1-024 Boulders, Sledging Piling etc Cu.m 3,740.00 4,060.00
87 E1-025 Rock Requiring Blasting Cu.m 3,665.00 3,985.00
88 E1-025A Hard Rock Blasting Use for chemical Cu.m 13,280.00 14,425.00
89 E1-025B Hard Rock Blasting Use for chemical & Piling Cu.m 14,770.00 16,044.53
90 E1-026 Rock Requiring Blasting and Piling (Bank Measurement) Cu.m 5,600.00 6,085.00
Roadway Excavation in Unclassified Soil Using Machinery
91 E1-027 Cu.m 172.00 187.00
Excluding Loading and Piling (Cutting Measurement)
Loading Materials by Machinery in Roadway Excavations (Cutting
92 E1-028 Cu.m 211.50 230.00
Measurement)
93 E1-029 Trimming / Cambering by Motor Grader (Cutting Measurement) Cu.m 40.75 44.25
94 E1-029A Trimming / Cambering by Motor Grader (Cutting Measurement) Sq.m 8.15 8.85

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Section 3 - Aggregate/RubbleAggregate / Rubble
Including Loading
95 A1-001 Sledging Available Rock 150-225mm Rubble including Loading Cu.m 3,025.00 3,285.00
96 A1-002 Blasting etc and Piling 150-225mm Rubble including Loading Cu.m 4,590.00 4,990.00
Blasting Sledging etc. and Piling 150-225mm Rubble using
97 A1-002A Cu.m 3,270.00 3,550.00
Compressor and Hand Held Drills including Loading
98 A1-003 Blasting etc. and Piling 100mm Aggregate including Loading Cu.m 5,050.00 5,485.00
99 A1-004 Blasting etc and Piling 75mm Aggregate incl/Loading Cu.m 5,810.00 6,310.00
101 A1-006 Blasting etc and Piling 37.5mm Aggregate incl/Loading Cu.m 8,075.00 8,775.00
50 mm Aggregate, Single Size Crusher Production Including
104 A1-009 Cu.m 2,040.00 2,215.00
Loading[SSCM 404.1-406.1 : Table 1701-4
37.5 mm Aggregate, Single Size Crusher Production Including
105 A1-010 Cu.m 2,725.00 2,960.00
Loading [SSCM 404.1-406.1 : Table 1701-4
106 A1-011 Cu.m 3,250.00 3,530.00
Loading [SSCM 404.1-406.1 ]
107 A1-012 Cu.m 2,610.00 2,835.00
Loading [SSCM 404.1-406.1 : Table 1701-4
Aggregate 37.5 mm Down Graded (SSCM-Table 1701.5 )
108 A1-013 Cu.m 2,725.00 2,960.00
Including Loading
109 A1-014 Crusher Fines 6.3 mm Down, Including Loading for 1.0 cu.m Cu.m 2,090.00 2,270.00
110 A1-014A Crusher Fines (DUST), Including Loading for 1.0 cu.m Cu.m 1,845.00 2,005.00
Aggregate 19 mm for Seal Coat Treatments as per SSCM Table
111 A1-015 Cu.m 3,250.00 3,530.00
1701-8, Including -Do-
Aggregate 12.5 mm for Seal Coat Treatments as per SSCM Table
112 A1-016 Cu.m 4,060.00 4,410.00
1701-8, Including -Do-
Blended aggregate for Rectification overlay, with 37.5 mm Single
size Aggregate and 19mm &12.5 mm Crushed Aggregated Mixed
113 A1-017 Cu.m 3,435.00 3,730.00
in the volume Ratio of 7:2:1: Including Mix. & Loading (Piling to
pay Separately)
114 A1-018 Piling Available Aggregate Cu.m 210.00 228.00
115 A1-019 Piling Available Rubble Cu.m 420.00 456.50
116 A1-020 Loading Available Aggregate / Rubble Cu.m 378.00 410.50

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Section 4 - Earth Filling & Compaction
Approved Earth Filling and Compaction
Approved Soil (Type I & II Materials) Excavation for Bases &
117 EW-001 Shoulder Construction Including Loading and Piling (Loose Cu.m 2,250.00 2,445.00
Volume) [SSCM 601.4]
118 EW-002 Spreading Piled Approved Soil (Loose Volume) Cu.m 282.50 306.50
Approved Soil Spread & Rolled Including Roller Hire Charges,

119 EW-003 Cu.m 552.00 599.00
Fuel & Watering (Loose Volume) [SSCM 601.1 - 4]
Approved Soil Spread & Rolled Using Machinery Including Motor

120 EW-003A Grader & Roller Hire Charges, fuel & Watering (Loose Volume) Cu.m 252.00 252.00
[SSCM 601.1 - 4]
Approved Soil Spread & Rolled in Strips Where Average Width is

121 EW-004 less than 1.2 meters for Road Widening including Roller Hire Cu.m 672.00 730.00
Charges, fuel & Watering (Loose Volume) [SSCM 601.1 - 4]
Approved Soil Spread & Compacted in Places Behind Abutments

and Structures, Shoulders about Sub Bases level and in Service
122 EW-006 Cu.m 669.00 727.00
line Trenches, Using 1/2 to 1 Ton Vibrating Roller Including
Watering (Loose Volume) [SSCM 601.1 - 4]
Approved Soil Spread & Compacted in 150 to 225 mm Thick

123 EW-007 Cu.m 703.00 764.00
Layers Using Machine Rammer at Narrow Places (Loose Volume)
Spreading , Leveling and Compacting Manually Using Standard

124 EW-008 Cast Iron Stamper or Equivalent and Filling in 150-225 mm Thick Cu.m 851.00 924.00
Layers (Loose Volume)
Trimming , Leveling and Compaction of Original
125 EW-009 Sq.m 82.50 89.75
Ground/Subgrade to 100 % STD Density [SSCM 304.3(c)]
Trimming , Leveling and Compaction of Original
126 EW-010 Sq.m 75.00 81.50
Ground/Subgrade to 95 % STD Density [SSCM 304.3(c)]
Approved Soil Excavation for Embankment Filling Including
127 EW-011 Cu.m 1,825.00 2,125.00
Loading and Piling (Loose Volume) [SSCM 601.1 TO 601.4]
Approved Soil (Type I & II Materials) Excavation using
128 EW-013 Machinery for Bases & Shoulder Construction Including Loading Cu.m 670.00 728.00
and Piling (Loose Volume) [SSCM 601.1 - 4]
Approved Soil (Type I & II ) Excavation using Machinery for
129 EW-014 Embankment filling Including Loading and Piling (Loose Cu.m 664.00 721.00
Volume) [SSCM 601.1 - 4]
130 EW-015 Grading and Spreading by motor grader Cu.m 75.25 81.75
Section 5 - Rubble Pitching/PavingRubble to be
Paid Separately
131 P1-001 Pitched Paving 225 mm Thick(Excluding cost of rubble) Sq.m 512.00 556.00
132 P1-002 Pitched Paving 150 mm Thick -do - Sq.m 384.00 417.00
133 P1-003 Flat Paving 150 mm Thick - do-- Sq.m 256.00 278.00
134 P1-004 Flat Paving 225 mm Thick - do-- Sq.m 340.50 370.00

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Section 6 - Aggregate Spreading &

RollingAggregate Spreading and Compaction -
Cost of Water to be Deducted from Rate if not
Carried Out under the Relevent Items
Spreading , Watering & Rolling 100 mm Aggregate Including Hire
135 M1-001 Cu.m 1,265.00 1,375.00
Charges of roller (Loose Volume) [SSCM 304.3(d),(e)]
Spreading , Watering & Rolling 100 mm Aggregate Including Hire
136 M1-001A Charges of roller (Loose Volume) [SSCM 304.3(d),(e)]below Cu.m 1,900.00 2,060.00
11.32 Cum
Braking Road Surface to 50 mm Depth by Hand , Screen &
137 M1-002 Sq.m 142.00 154.00
Replace Old Aggregate
Scarifying Road Surface to 50 mm Depth by roller, Screen, &
138 M1-003 Sq.m 110.50 120.00
Replace Old Aggregate.
Spreading & Compaction 50-19 mm New Aggregate by Roller
139 M1-004 Including Watering Hire Charges of Roller, Etc. (Loose Volume) Cu.m 1,895.00 2,060.00
[SSCM 403.3(c)]
Spreading & Compaction 50-19 mm New Aggregate For Extensive
Patching by Roller Including Watering Hire, Etc. (Loose Volume)
140 M1-004A Cu.m 2,945.00 3,200.00
[SSCM 403.3(c)]
Breaking 50 mm Additional Depth by Hand Screening &

141 M1-005 Sq.m 86.00 93.25
Replacing Old Aggregate
Scarifying 50 mm Additional Depth With Roller, Screening &
142 M1-006 Sq.m 89.75 97.50
Replacing Old Aggregate
Spreading Watering & Compacting 50-19 mm Aggregate in Edge
143 M1-007 Correction using roller Including Hire, Etc. (Loose Volume ) Cu.m 2,380.00 2,585.00
[SSCM 1103.3]
Spreading watering & Compacting 50-19 mm Aggregate in Edge
144 M1-008 Correction Using Roller Including Hire ,Etc (Loose Volume) Cu.m 1,940.00 2,110.00
[SSCM 1103.3]
Spreading & Compacting 50-19 mm Aggregate by 8-10 ton Roller
145 M1-009 After Applying track Coat in Overlay (Loose Volume) (Tack Coat Cu.m 1,755.00 1,905.00
Paid Separately)
Spreading & Compacting 50-19 mm Aggregate by 8-10 ton Roller
146 M1-009A After Applying track Coat in Overlay (Loose Volume) (Tack Coat Cu.m 2,740.00 2,975.00
Paid Separately) below 9.91 cum within km
Water Bound Macadam Spreading watering and Compacting 50-
25 mm Aggregate and Filling the Voids to refusal with Crusher
147 M1-010 fines by watering and rolling to form a water bound Macadam Cu.m 6,245.00 6,780.00
Base Excluding transport for Aggregates and fines. Loose Volume
(SSCM 404.1)
Dry Bound Macadam Spreading watering and compacting 50-25
mm Aggregate and filling the voids to refusal with Crusher Fines
148 M1-011 by Rolling with Vibrating Roller to Form a Dry Bound Macadam Cu.m 5,960.00 6,475.00
base Excluding Transport for Aggregates and Fines (Loose
Volume) [404]
Dense Graded Aggregate Base (Aggregate Base Course)

Seprading watering and Compacting Graded 37.5 mm Aggregate
149 M1-012A to Form a Dense Aggregate Base Using Machinery Including Cu.m 3,145.00 3,415.00
Motor Grader & Roller Hire Charges. Transport of Aggregates to
be Paid Separately (Loose Volume)

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Dense Graded Agg.Base [ABC], Spreading Watering and
Compacting Graded 37.5mm Aggregate to form a Dense
150 M1-013 Aggregate Base in Strips, Av Width not exeeding 1.2m for Road Cu.m 4,615.00 5,015.00
Widening excl Transport of Aggregate(Loose Volume) [SSCM
405.1 -.4]
Graded 37.5 ABC Material Spread and Rolled in Strips, Average
Width not Exceeding 1.2m Using Machinery inch Motor Graders
151 M1-013A Cu.m 3,325.00 3,610.00
and Roller Hire Charges Fuel and Watering (Loose Vol) [SSCM
405.1-.4]

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Section 7 - Road Surface Treatment
Transport of Emulsion/Bitument to be Paid
Separately.
Bitumen Surface 1st Coat Using 2ltr/Sq.m including Blinding with
152 S1-001 Sq.m 260.50 283.00
Sand @ the Rate of 125 Sq.m/Cu.m [SSCM 503.1]
Bitumen Surface 1st Coat Using 2ltr/Sq.m including Blinding with
153 S1-001A Sand @ the Rate of 125 Sq.m/Cu.m [SSCM 503.1] Sq.m 103.00 110.00
(Authority Bitumen )
Bitumen Surfacing 1St Coat using 2ltr/Sq.m including Blinding
154 S1-002 Sq.m 249.50 271.00
with Gravel where Sand is not Available within 16km.
Bitumen Surfacing 1St Coat using 2ltr/Sq.m including Blinding
155 S1-002A with Gravel where Sand is not Available within 16km. Sq.m 91.50 99.50
Double Bituminous Surface Treatment with Hot Bitumen (Manual)
156 S1-003 including Internal Transport (Binder and Aggregate Paid Sq.m 268.00 291.50
Separately) [SSCM 505.1-.5 and Table 505.1]
Single Bituminous Surface Treatment with Hot Bitumen (Manual,
157 S1-004 including Internal Transport) (Binder and Aggregate Paid Sq.m 141.00 153.00
Separately) [SSCM 505.1-.5 and Table 505.1]
Double Bituminous Surface Treatment with Emulsion (CRS-1)
158 S1-005 (Manual including Internal Transport) (Binder and Aggregate Paid Sq.m 260.50 283.00
Separately)
Single Bituminous Surface Treatment with Emulsion (CRS-1)
159 S1-006 (Manual including Internal Transport) (Binder and Aggregate Paid Sq.m 136.50 148.00
Separately)
Bitumen Surfacing Subsequent Coat using 0.75ltr/Sq.m including

160 S1-007 Sq.m 137.50 149.50
Blinding with Sand @ 125 Sq.m/Cu.m [SSCM 503.1(b)]

161 S1-007A Blinding with Sand @ 125 Sq.m/Cu.m [SSCM 503.1(b)] Sq.m 78.50 85.25
Bitumen Surfacing 2nd/Subsequent Coat using 1.0ltr/Sq.m
162 S1-008 including Blinding with Sand @ 125 Sq.m/Cu.m (New Work) Sq.m 157.50 171.00
[SSCM 503.1(b)]
163 S1-008A including Blinding with Sand @ 125 Sq.m/Cu.m (New Work) Sq.m 78.75 85.50
[SSCM 503.1(b)](Department Bitumen)

164 S1-009 Sq.m 126.50 137.50
Blinding with Gravel @ 125 Sq.m/Cu.m [SSCM 503.1(b)]

165 S1-009A Blinding with Gravel @ 125 Sq.m/Cu.m [SSCM 503.1(b)] Sq.m 67.25 73.25
166 S1-010 including Blinding with Gravel where Sand is not Available within Sq.m 146.50 159.00
16km (New Work) [SSCM 503.4(c)]

167 S1-010A including Blinding with Gravel where Sand is not Available within Sq.m 67.75 73.50
16km (New Work) [SSCM 503.4(c)] (Authority Bitumen )
Emulsion/Cold Bitumen(CRS-1) Surface Treatment Ist Coat with

168 S1-011 3.5 ltr/Sq.m Including Blinding with Sand, @ 125 Sq.m/Cu.m Sq.m 282.50 307.00
(Manual)

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Emulsion/Cold Bitumen(CRS-1) Surface Treatment Ist Coat with
169 S1-012 3.5 ltr/Sq.m (Using Trolley, Emulsion) Including Blinding with Sq.m 263.50 286.50
Sand, @ 125 Sq.m/Cu.m (Manual)
Emulsion/Cold Bitumen(CRS-1) Surface Treatment Subsequent
170 S1-013 Coat with .75 ltr/Sq.m Including Blinding with Sand, @ 125 Sq.m 97.50 106.00
Sq.m/Cu.m (Manual)
Emulsion/Cold Bitumen(CRS-1) Surface Treatment Subsequent
171 S1-014 Coat with .75 ltr/Sq.m (Using Trolley, Emulsion) Including Sq.m 90.50 98.25
Blinding with Sand, @ 125 Sq.m/Cu.m
Tack Coat Using Emulsion (CRS-1) @ the Rate of 0.5 ltr/Sq.m
172 S1-015 inclusive of Brushing, Cleaning Road Surface and Cost of Sq.m 58.00 63.00
Emulsion (Manual) [SSCM 502.3]
173 S1-016 inclusive of Brushing, Cleaning Road Surface and Cost of ltr 116.00 126.00
Emulsion (Manual) [SSCM 502.3]
174 S1-017 inclusive of Brushing, Cleaning Road Surface and Cost of Sq.m 77.00 83.75
Emulsion (Manual) [SSCM 502.1-503.3]
Tack Coat with 30% Cut Back Bitumen Using 0.5 ltr/Sq.m
175 S1-018 Sq.m 82.25 89.25
Including Brushing and Cleaning Road Surface (Manual)
176 S1-018A Including Brushing and Cleaning Road Surface (Manual) Sq.m 54.75 59.50
177 S1-019 ltr 329.00 357.50
Including Brushing and Cleaning Road Surface (Manual)
178 S1-020 Including Brushing and Cleaning Road Surface (Manual) [SSCM Sq.m 103.00 112.00
503.4(d)]
Rolling over Blinding Material Spread over Subsequent Bitumen

179 S1-021 Sq.m 15.25 16.55
Surfacing using diesel Roller (8-10 Tones) [SSCM 503.4(d)]
Prime Coat with Emulsion/Cold Bitumen(CSS-1) Using 1 Ltr/Sq.m

180 S1-022 Including Blinding with Sand at The Rate of 250 Sq.m/Cu.m and Sq.m 118.00 128.50
Brushing Cleaning and Moistening Road Surface

181 S1-022A Sq.m 110.50 120.00
Part A of Item S1-022
182 S1-022B Sq.m 7.40 8.05
Part B of Item S1-022
183 S1-023 without Blinding, but Inclusive of Brushing, Cleaning and Sq.m 96.75 105.00
Moistening Road Surface
Prime Coat With 30% Cut Back Bitumen Using 1 Ltr/ Sq.m
184 S1-024 Including Blinding with Sand at the rate of 250 Sq.m/Cu.m and Sq.m 146.00 158.50
Brushing, Cleaning and Mostening Road Surface
Prime Coat With 30% Cut Back Bitumen Using 1 Ltr/ Sq.m
185 S1-025 without Blinding but Inclusive Brushing, Cleaning and Mostening Sq.m 124.00 134.50
Road Surface
186 S1-026 Sweeping Over Tarred Surface to Arrest Bleeding. Sq.m 5.95 6.50
Application of Asphalt Emulsion for Surface Treatment Using
187 S1-027 ltr 73.00 79.25
CRS-1 (Using Plant) "Rate per Litre"
Blinding the Bitumen Surfacing with Sand at the rate of 125 Sq.m1
188 S1-028 Sq.m 43.50 47.25
Cu.m Using Material from Stock Pile

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Single Bituminous Surface Treatment With Emulsion (CRS-1)
Using Plant.(Binder and Aggregate Paid Separately) (Rate to
189 S1-029 Include Transport cost of Aggregate up to 16KMS) [SSCM Sq.m 75.00 81.50
505.5(b)]
Double Bituminous Surface Treatment with Emulsion(CRS-1)

190 S1-030 Using Plant. (Binder and Aggregate Paid Separately) (Rate of Sq.m 154.00 167.00
include Transport cost of Aggregate up to 16 KMS)
Lay and Compact Asphalt Premix Usign Paver (Cost of premix,

191 S1-034 M.ton 1,735.00 1,885.00
Aggregate Transport and premix transport to vbe paid Separately)
Bitumen Surfacing (Sand Sealing -Manual) Using Emulsion (CRS

1) @ 1 LTR. /SQ.M Including Preparing Surface, Blinding with
192 S1-035 Sand @ 4 CU.M/500 SQ.M and Pressing with hand Sq.m 117.50 127.50
Rollers.(Patching pot holes if necessary & external transport to be
pay sep.
Patching Minor Pot Holes Using Sand Emulsion Mix 1:8 Where
193 S1-035A Sq.m 22.10 24.00
Necessary, Prior to Sand Sealing.
Sand Sealing with Emulsion CRS-1 at the Rate of 1Ltr,Sq.m Using

Plant.Incd.Brushing,cleaning, Blinding. with Sand@ 125 Sq.mand
194 S1-036 Sq.m 141.50 162.00
Rolng. with pneumatic. roller & internal trnsport.[SSCM 504]
Reconstruct Base With Penetration Macadam Using Nominal Size

50mm Aggregate and 19mm Key Aggregate from Stock Piles, to
195 S1-037 Sq.m 210.50 229.00
Accomplish 75mm on Existing Pavements[SSCM 406] (Binder,
Aggregate, Transport paid Separately)
Reconstruct Base with Penetration Macadam Using Nominal Size

37.5 mm Aggregate and 12.5 mm Key Aggregate from Stock Piles
196 S1-038 Sq.m 296.00 322.00
, to a compacted thickness of 55mm on existing pavements [SSCM
406] cost of aggregate including transport to be paid separately
Correction of Corrugations, Depressions and Cambering road

Surfaces using asphalt Concrete compacted by Vibrating roller
197 S1-039 M.ton 2,740.00 2,975.00
Including Internal transport (application of tack coat and Supply of
Asphalt concrete to ve paid separately)
Sand sealing with emulsion crs-2 at the rate of .8 Ltr/Sq.m using

plant , and blinding with sand at the rate of 125Sq.m/Cu.m on
198 S1-040 Sq.m 126.00 137.00
D.B.S.T./S.B.S.T. (Triple Seal) including Internal transport
(SSCM 504) binder transport to site to pay separately
199 S1-040A Sand sealing with emulsion crs-2 - Part A of Item S1-040 Sq.m 86.00 93.50

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Section 8 - Road Maintenance
Internal Transport of Hot Bitumen up to 16km
and Sand Transport up to 16km Included in the
Rates.
Patching with Hot Bitumen Using 14 Liters per 1/2 km (SSCM
200 MN-001 km 3,330.00 3,615.00
1102.1-3)
201 MN-002 Patching With hot Bitumen Using 21 Ltrs. Per 1/2 K.m. 1/2 K.m 4,990.00 5,425.00
207 MN-008 Extensive Patching for Every Additional 7 Ltrs. Hot Bitumen 1/2 K.m 1,665.00 1,810.00
208 MN-009 Patching with Cold Bitumen (CRS-1) Using 14 Ltrs per 1/2 K.m. km 2,140.00 2,325.00
209 MN-010 Patching with Cold Bitumen (CRS-1) Using 21 Ltrs. Per 1/2 K.m. 1/2 K.m 3,215.00 3,490.00
Extensive Patching for Every Additional 7 Ltrs. Cold Bitumen,

215 MN-016 1/2 K.m 1,070.00 1,165.00
CRS-1
216 MN-017 50 mm-19mm Aggregate Roller Patching Cu.m 5,565.00 6,045.00
217 MN-018 50 mm - 19mm Aggregate Stamped Patching Cu.m 6,615.00 7,185.00

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Section 9 - Road Side Drainage System
Rate to Include Spreading the Resulting
Materials Suitably in the Vicinity Unless
Otherwise Directed.
218 DR-001 Cutting New Side Drains in Ord. Soil Cu.m 1,100.00 1,195.00
219 DR-002 Cutting New Side Drains in Med. Soil Cu.m 1,520.00 1,650.00
220 DR-003 Cutting New Side Drains in Hard Soil Cu.m 1,940.00 2,105.00
221 DR-004 Cutting New Side Drains in Soft Soil Cu.m 2,150.00 2,335.00
222 DR-005 Cutting New Side Drains In Unclassified Soil Cu.m 1,520.00 1,650.00
Cutting side drains of std. Dimensions in unclassified soil using
223 DR-005A machine (Back hoe J.C.B) including shipping trimming and Cu.m 732.00 795.00
leveling bottom manually
224 DR-006 Cutting New Side Drains in Rock Cu.m 4,180.00 4,540.00
Turfing (Excluding Royalty, Transport and Watering Maintenance)
225 DR-007 Sq.m 232.00 252.00
[SSCM 802.3 (a)]
Watering and Maintaining Turf For Three Months Including
226 DR-008 Sq.m 294.50 319.50
Transport of Water
227 DR-009 Leveling & Trimming Earth Sq.m 31.00 33.75
228 DR-010 Clearing Silt Etc. from Kerbs & Channels (SSCM 12053) L.m 18.50 20.10
Cutting Scupper Drains on any Soil Other than Rock to and
229 DR-011 Average width of 0.75 m with proper Gradient and Ave. Depth of L.m 136.50 148.00
100 mm (SSCM 1304.3)
230 DR-012 Clearing and Desilting of Culverts (SSCM 1303.3) L.m 382.00 415.00
231 DR-013 Clearing Choked Culverts (With Head Room > 1m.) Cu.m 1,565.00 1,700.00
Cleaning desilting existing side drains and lead up drains to proper
232 DR-014 shape and gradient and transport of excavated materials from road L.m 46.50 50.50
side up to 100m
233 DR-015 Clearing Inlets and Outlets of Culverts Culverts 344.00 374.00

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Section 10 - Bridges & Culverts
Bridges Culverts and Retaining Walls etc.
Demolishing Dry Coursed Masonry Including Stacking or Loading
234 ST-001 Cu.m 4,620.00 5,020.00
,(SSCM 202.2)
Demolishing Coursed Masonary in cement Mortar Including
235 ST-002 Cu.m 5,380.00 5,840.00
Stacking or Loading
Demolishing Random Rubble Masonry in cement Mortar Including
236 ST-003 Cu.m 2,435.00 2,645.00
Stacking or Loading
Random Rubble Masonry, 150-225 mm Rubble in Approved
237 ST-004 cement & Sand Mortar 1:6 (Excluding Transport of Rubble & Cu.m 13,185.00 13,330.00
Piling) [SSCM 1006.3]
Random Rubble Masonry, 150-225 mm Rubble in Approved
238 ST-005 cement & Sand Mortar 1:5 (Excluding Transport of Rubble & Cu.m 13,570.00 14,740.00
Piling) [SSCM 1006.3]
Random Rubble Masonry, in Approved cement & Sand Mortar 1:6
239 ST-006 Cu.m 12,190.00 12,250.00
With available Rubble 150-225mm
Random Rubble Masonary in approved cement & sand Mortar 1:5
240 ST-007 Cu.m 12,575.00 13,660.00
with Available Rubble 150-225 mm.
Dry Masonry With available Heavy Rubble or Boulders(SSCM
241 ST-008 Cu.m 7,775.00 8,445.00
1006.3)
Dry Masonry With Rubble 150-225 mm (Excluding Transport of
242 ST-009 Cu.m 6,875.00 6,475.00
Rubble & Piling)
243 ST-010 Dry Masonry With available Bubble 150-225mm Cu.m 6,300.00 6,845.00
Packing Available Rubble and Aggregate Filter Layers Behind
244 ST-011 Cu.m 1,380.00 1,495.00
Masonry Walls.
Clay Puddled & Layid Behind Masonry Walls(Excl.Transport of
245 ST-012 Cu.m 2,785.00 3,025.00
Clay) [SSCM 705.3]
Grouting Coursed Stone Masonry Joints With approved Cement &
246 ST-013 Sq.m 556.00 604.00
Sand Mortar 1:3 (SSCM 804.2(c))
Grouting Rubble Paving With Concrete Class C, 1:2:4(19 mm)
247 ST-014 Cu.m 2,570.00 2,790.00
(Excl. Transport of Aggr. For Concrete & Piling)
Grouting Rubble Paving with approved cement & Sand mortar
248 ST-015 Sq.m 912.00 991.00
(1:3)
Forming weep Holes In Masonry Construction (Labour only)
249 ST-016 No 595.00 646.00
[SSCM 706.3]
Forming Weep Holes Using P.V.C. Pipes of Int. Dia. Not less than
250 ST-017 L.m 713.00 775.00
100mm Complete with Dripledge and Surround Finish Smooth.
Shoring with 37.5 mm Thick Class II Timber Planks up to 3 m

251 ST-018 Sq.m 975.00 1,060.00
Depth
Supplying & Fixing class II Timber Struts Etc. For Shoring up to
252 ST-019 Sq.m 98.75 107.00
3m Depth
Supplying and Fixing Class II Timber in Shoing up to 3m Depth

253 ST-020 Sq.m 1,220.00 1,325.00
(Rate per Area Basis)
254 ST-021 Lifting Soil For Every 1.5 m Beyond the Initial 1.5m Cu.m 756.00 821.00
255 ST-022 Lifting Wedge Stones For Every 1.5 m Beyond the Initial 1.5m Cu.m 2,270.00 2,465.00
256 ST-023 Lifting Rubble or Concrete Every 1.5 m Beyond the Initial 1.5m Cu.m 1,135.00 1,230.00
Lowering Wedged Stones Evety 1.5m Beyond the Initial 1.5 m

257 ST-024 Cu.m 1,515.00 1,645.00
Beyond the Initial 1.5 m
258 ST-025 Lowering Rubble or Concrete Every 1.5m Beyond the Initial 1.5 m Cu.m 756.00 821.00

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
259 ST-026 PCC Beams(10.5m to 13.5m) Launched into Position No 855.00 929.00
Rendering 12.5 mm thick in cement sand Motar 1:2 mix (Smooth
260 ST-027 Sq.m 1,035.00 1,125.00
Finish)
261 ST-028 Rendering 19 mm thick in cement sand Motar 1:2 mix (Rough) Sq.m 1,235.00 1,340.00
Rendering 19 mm thick in cement sand Motar 1:2 mix (Smooth

262 ST-029 Sq.m 1,375.00 1,495.00
finish)
263 ST-030 Rendering 12.5 mm thick in cement sand Motar 1:3 mix (Rough) Sq.m 872.00 947.00
Rendering 12.5mm thick in cement sand Motar 1:3 mix (Smooth

264 ST-031 Sq.m 1,025.00 1,110.00
finish)
265 ST-032 Rendering 19 mm thick in cement sand Motar 1:3 mix (Rough) Sq.m 1,205.00 1,310.00
Rendering 19mm thick in cement sand Motar 1:3 mix (Smooth

266 ST-033 Sq.m 1,345.00 1,465.00
finish)
Mixing & Laying Manually, cement Concrete 1:4:8 (50 mm)
267 ST-034 (Volume Batching) Using Crusher run Aggregate (Excl. Transport Cu.m 14,799.63 16,075.46
of Aggregate & Piling) [SSCM 1001.4]
Mixing & Laying Using Concrete Mixer,Cement Concrete 1:4:8

268 ST-035 (50 mm) (Volume Batching) Using Crusher Run Aggregate (excl. Cu.m 12,435.00 13,510.00
Transport of Aggregate & Piling) (SSCM 1001.8 - 9)
Mixing & Laying Manually Cement Concrete 1:4:8 (50 mm) with
269 ST-036 20% Plums (Volume Batching) Using Crusher Run Aggregate Cu.m 13,500.00 14,660.00
(excl. Transport of Aggregate & Piling)
Mixing & Laying Using Concrete Mixer, Cement Concrete 1:4:8

270 ST-037 (50 mm) with 20% Plums (Volume Batching) Using Crusher Run Cu.m 12,155.00 13,200.00
Aggregate (excl. Transport of Aggregate & Piling)
Mixing & Laying Manually Cement Concrete 1:3:6 (37.5 mm)

271 ST-038 with 20% Plums (Volume Batching) Using Crusher Run Cu.m 14,560.00 15,815.92
Aggregate (excl. Transport of Aggregate & Piling)

272 ST-039 (37.5 mm) with 20% Plums (Volume Batching) Using Crusher Cu.m 12,195.00 13,245.00
Run Aggregate (excl. Transport of Aggregate & Piling)

273 ST-040 (Volume Batching) Using Crusher Run Aggregate (excl. Transport Cu.m 16,776.14 18,222.36
of Aggregate & Piling)[SSCM 1001.4]
274 ST-041 (37.5 mm) (Volume Batching) Using Crusher Run Aggregate Cu.m 15,422.24 16,751.74
275 ST-041A (37.5 mm) with 20% plums Using Crusher Run Aggregate (excl. Cu.m 14,375.00 15,615.45
Transport of Aggregate & Piling)
Mixing & Laying Manually Cement Concrete 1:3:6 (19 mm)
of Aggregate & Piling)

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
279 ST-045 (37.5 mm) (Volume Batching) Using Crusher Run Aggregate Cu.m 8,275.00 8,275.00
Mixing & Laying Manually Cement Concrete 1:2:4 (19 mm)
Mixing & Laying Using Concrete Mixer (W/Batching), Cement

282 ST-048 Concrete for Grade 25 (19 mm) Using Crusher Run Aggregate In Cu.m 19,148.31 20,799.02
Foundation and Floors. (excl. Transport of Aggregate & Piling)

283 ST-048A Concrete for Grade 25 (70% 37.5 + 30% 19 mm) Using Crusher Cu.m 17,066.51 18,537.76
Run Aggregate (excl. Transport of Aggregate & Piling)

284 ST-049 Concrete for Grade 30 (19 mm) With Crusher Run Aggregate Cu.m 19,171.23 20,823.93
285 ST-050 Concrete for Grade 40 (19 mm) With Crusher Run Aggregate Cu.m 22,085.00 23,988.88
286 ST-051 Mixing & Laying Using Concrete By Hand Cu.m 6,880.00 7,475.00
Mixing & Laying Using Concrete By Power Driven Concrete
287 ST-052 Cu.m 5,530.00 6,005.00
Mixer V/Batching
Curing of Concrete Decks, Slabs , Beams, Walls etc. [SSCM
288 ST-053 Sq.m.Day 47.50 51.75
1011.11]
289 ST-054 Fabricate & Lay M.S Bars as Reinforcement (Excl. Transport) kg 321.50 349.50
290 ST-055 Fabricate & Lay Tor Steel as Reinforcement (Excl. Transport) kg 321.50 349.50
Cutting & Laying Reinforcment Fabric (Excluding Cost of

291 ST-056 kg 323.00 351.00
Reinforcement Fabric)
Supplying & fixing 25 mm Thick Planks of Class II Timber as
292 ST-057 Shuttering, Including removing [1008.3(b)] Sq.m 1,205.00 1,305.00
Supplying & Fixing Class II Timber Bearers, Joists , Etc. Including

293 ST-058 Cu.dm 74.25 80.75
Dismantling in Shuttering (SSCM 1008.3 (a))
100-150 mm Dia. Round Jungle Timber Supplied & Fixed as
294 ST-059 L.m 137.50 149.00
Props
150-200 mm Dia. Round Jungle Timber Supplied & Fixed as
295 ST-060 L.m 155.00 168.50
Props
Formwork Smooth Finish With Class II Timber For Bridge Beams,
296 ST-061 Bridge Deck Under Sides and Sides Including Dismantling (SSCM Sq.m 3,140.00 3,410.00
1008.3(b))
Formwork Smooth Finish With Class II Timber For Bridge
297 ST-062 Sq.m 2,920.00 3,170.00
Column Shafts Including Dismantling (SSCM 1008.3(b))
Formwork Smooth Finish, Using Plywood (Shutter 15 mm) and
298 ST-063 Class II Timber Bearers, Joists and Jungle Timber Props for Sq.m 3,430.00 3,725.00
Bridge Abutments, Wing walls Etc.
Supplying & fixing 25mm Thick Planks and Struts of Class II
299 ST-064 Timber as Formwork Rough Finish, in Foundation Etc. Including Sq.m 1,485.00 1,615.00
Removing (SSCM 1008.3(b))

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Formwork Smooth Finish for General Purposes, Using 25mm
300 ST-065 Thick Planks & Struts of Class II Timber and Round Jungle Sq.m 2,100.00 2,285.00
Timber Props 100 - 150 mm Dia. Including Dismantling
Supplying , Laying & Jointing 152mm Dia. Concrete Pipes
301 ST-066 (Transport and Bedding Material paid separately) [SSCM 707.3 - L.m 3,125.00 3,395.00
4]
Supplying ,Lalying & Jointing 229mm Dia. Concrete Pipes
4]
Supplying ,Laying & Jointing 305mm Dia. Concrete Pipes
4]
4]
4]
4]
4]
Laying & Jointing 152 mm Dia. Available Concrete Pipes and
308 ST-073 L.m 939.00 1,020.00
Collars
309 ST-074 L.m 997.00 1,080.00
Collars
Laying & Jointing 305-450 mm Dia. Available Concrete Pipes and
310 ST-075 L.m 1,080.00 1,170.00
Collars
311 ST-076 L.m 2,125.00 2,310.00
Collars
312 ST-077 L.m 3,515.00 3,820.00
Collars
313 ST-078 L.m 5,000.00 5,430.00
Collars
Fixing new Bridge Planks Runners and Stacking old Planks
314 ST-079 No 1,310.00 1,420.00
(Available) [SSCM 1402.2(a)]
315 ST-080 Removing & Re-Setting old Bridge Planks No 817.00 888.00
316 ST-081 Supplying & Fixing new Bridge Planks of Class I Timber No 129.50 140.50
317 ST-082 Supplying & Fixing 31 mm Thick Deck Planks of Class I Timber No 5,825.00 6,330.00
Fixing New Chequered or M.S. Plates on Timber - Decked Bridge

318 ST-083 L.m 1,930.00 2,095.00
[SSCM 1402.2(d)]
Removing & Refixing Chequered M.S. Plates on Timber-Decked
319 ST-084 L.m 2,575.00 2,795.00
Bridge
320 ST-085 Tightening Bolts & nuts of Chequered of M.S. Plates L.m 370.50 402.50
321 ST-086 Removing & Refixing "U" Clips. [SSCM 1402.2(b)] L.m 285.50 310.00
Cleaning, Wire Brushing & Painting Steelwork, One Coat Enamel
322 ST-087 Sq.m 334.50 363.00
Paint
323 ST-088 Cleaning, Wire Brushing & Applying Tar on Steelwork, One Coat Sq.m 246.00 267.50
Cleaning, with Cotton Waste and Painting Steel Work with Enamel
324 ST-089 Sq.m 208.50 226.50
Paint, One Coat

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Chipping to Bare Metal etc. & Painting with Anticorrosive Paint,
325 ST-090 Sq.m 1,130.00 1,225.00
One Coat
Painting with One Coat of Enamel Paint after Cleaning, Derusting

326 ST-091 Sq.m 797.00 866.00
& Application of One Coat Anticorrosive Paint[SSCM 1401.3(C)]
Painting with Two Coats of Enamel Paint, after Cleaning,

327 ST-092 Sq.m 992.00 1,080.00
Degusting & Application of One Coat Anticorrosive Paint
328 ST-093 Oiling Steel Cables on Suspension Bridges [SSCM 1405.3] Sq.m 976.00 1,060.00
Cleaning Booms of Steel Bridges including Scaffolding where
329 ST-094 L.m 88.50 96.25
Necessary [SSCM 1401.3]
Demolishing Unreinforced Cement Concrete Including Cleaning
330 ST-095 of Debris in Foundation and Superstructure in Dry Condition Cu.m 4,240.00 4,605.00
Excluding Under Water Structures [SSCM 202.2]
331 ST-096 Demolishing Reinforced Concrete and Debris Cleared Cu.m 6,045.00 6,565.00
Demolishing Reinforced Concrete in Very Heavy Structures Build

332 ST-097 Up of Grade 30 Above Concrete in Work Such As Bridge Beams Cu.m 13,645.90 14,822.27
& Deck Slabs, Including Collecting and Removing
Supplying and Fixing M.S. Dowels Spliced and Dove Tailed with
333 ST-098 Wedge at One End, 16mm dia, and 1m long, Boring Holes to 0.3m No 1,005.00 1,090.00
Depth in Fixing
Supplying and Fixing M.S. Dowels, Spliced and Dove Tailed with
334 ST-099 Wedge at One End, 20mm dia, and 1m Long, Boring Holes to No 1,245.00 1,355.00
0.3m Depth in Fixing.
Supplying & Fixing M.S.Dowels, Spliced and Dove Tailed with
335 ST-100 Wedge at One End, 25mm dia, and 1m Long. Boring Holes to No 1,665.00 1,805.00
0.3m Depth in Fixing.
Lay Standard Type Road Kerbs(125mmX900mm) Set on19mm

336 ST-101 thick 1:3 Cement Mortar Layer on 150mm X 275mm 1:2:4(19) L.m 2,825.00 3,070.00
Concrete Foundation With av. 157mm X 150mm Backing
Lay Standard Precast Bridge Kerbs [Type Drawing No T/B/106-

337 ST-102 Rev 1 of RDA](Cost of Precast Kerbs & Transport to be Paid L.m 694.00 753.00
Separately)
Constructing 150x50mm thick Inset Lower Kerb in Grade
338 ST-103 20(14mm) Concrete for Bridges: ( Aggregate Transport to be Paid L.m 331.50 360.00
Separately)
Laying 450 X 450 X 50 mm Precast Concrete Slabs on Foot Walks
339 ST-104 Including av. 40mm Thick 1:3 Cement Mortar Bedding (Cost of Sq.m 2,020.00 2,190.00
Sabs & Transport Paid Separately)
340 ST-104A Mixing Cement Sand Mortar Using a Mixer Cu.m 19,466.91 21,145.10
Laying 450 x 450 x 50 mm Precast Concrete Slabs on Foot Walks
341 ST-105 Including av.40mm Thick Sand Bedding (Cost of Precast Slabs Sq.m 1,405.00 1,525.00
and Transport to be Paid Separately)
Fixing Precast Hand Railing and Uprights Using Grade 25(19)
Concrete Including Formworks for Pockets (Precast Items &
342 ST-106 L.m 1,875.00 2,040.00
Transport and Aggr.Transport paid Separately)[Type Dwg No
T/B/102/B]
Construction of RCC Grade 25(19mm) End Pillaster, Type 1(Agg.

343 ST-107 No 52,829.00 57,384.00
Transport to be Paid Separately) [Type Dwg No T/B/106-Rev 1]
Construction of RCC Grade 25(19mm) End Pillaster, Type II

344 ST-108 (Agg. Transport to be Paid Separately) [Type Dwg No T/B/106- No 58,666.00 63,734.00
Rev 1]

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Construction of RCC Grade 25(19mm) End Pillaster, Type III
Rev 1]
Construction of RCC Grade 25(19mm) End Pillaster, Type IV
Rev 1]
Laying of Grade 20 Concrete Precast pin Kerbs in Grade 20(19)
347 ST-111 Concrete Foundation as Edging (Aggregate transport to be Paid L.m 947.00 1,030.00
Separately)
Supplying and Fixing 25mm Thick Toung and Groved Planks with
348 ST-112 50x50mm Struts of Class 1 Timber in Panels as Smooth Shuttering Sq.m 764.00 830.00
for Concrete Drains
Supplying and Fixing 25mm Thick Toung and Groved Planks with
349 ST-112A 50x50mm Struts of Class 1 Timber in Panels as Smooth Shuttering use 7,420.00 8,060.00
for Concrete Drains(for 13.38 Sq.m)
Supply and Packing 50-200 mm Dry Stone lining Behind

350 ST-113 Cu.m 2,820.00 3,065.00
Abutments and wind walls (Aggregate Transport to pay separately)
Laying Geotextile on Prepared Surface Supply and Transport to

351 ST-114 Sq.m 82.75 89.75
pay Separately
Construction of Gabion Wall Using 4x1x1m Mesh Including
352 ST-115 Lacing Wire on Prepared Ground.(Supply and Transport of Gabion Cu.m 7,080.00 7,690.00
Mesh to be Paid Separately);
Construction of Gabion wall Using 4x1x0.5 m mesh including
353 ST-116 Lacing Wire on Prepared Ground (Supply and Transport of Gabion Cu.m 7,525.00 8,175.00
Mesh to be Paid Separately)
Construction of Kerb Inlet as per Drawing Type - K1/T1 With
354 ST-117 L.m 12,275.00 13,335.00
Cover Slabs. Aggregate Transport to pay Separately
Additional Labour For Pouring, Compacting and Levelling
355 ST-118 Cu.m 1,210.00 1,310.00
Concrete in Screed Under Foundation Slabs
Additional Labour For Pouring, Compacting Concrete in
356 ST-119 Abutments , Wingwalls, Capping Beams of Piers and Foot walks Cu.m 409.50 444.50
of Bridges
Additional Labour For Pouring, Compacting and Levelling infiller

357 ST-120 Cu.m 1,835.00 1,995.00
Concrete between Bridge Beams including Creed of Bridge Decks.
Leveling Ready mixed Grade Concrete Including Vibration

358 ST-121 Cu.m 2,475.00 2,690.00
(Supply of Concrete to be Paid Separately)
Supplying and laying Approved Hard Rubber Bearing Pads 75mm

359 ST-122 m. 1,830.00 1,985.00
x 12mm Over Capping Beams and Under the Approach Slabs
Bituminous Sealing Material Supplied and Laid Under Beam ends

360 ST-123 to Prevent Grout leak on to Capping Beam Transport of Emulsion L.m 167.50 182.00
Included.
230mm Dia. Polythene Displacers Supplied and Filled with Saw
361 ST-124 Dust or Similar Light Material in Deck. Transport of Saw Dust to L.m 95.25 103.50
be Paid Separately
325mm Dia Polythene Displacers Supplied and Filled with Saw
362 ST-125 Dust or Similar Light Material in Deck. Transport of Saw Dust to L.m 149.50 162.00
be Paid Separately
363 ST-126 PCC Beams(10.5m to 13.5m) Launching into Position No 11,190.00 12,155.00
M.S. Angle Iron and Hard Rubber Expansion Joints as Per
364 ST-127 L.m 9,160.00 9,945.00
Drawing No T/B/107 Rev. 1

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Section 11 - Road Furniture Items
Kilometer Posts and Guard Stones
365 RF-001 White Washing, Two Coats to Guide / Guard Stones No 86.25 93.75
Whitewashing Two Coats K.M. Stones inc. Numbering & Tar
366 RF-002 No 930.00 1,010.00
Skirting.
367 RF-003 Painting White Back Ground on Parapets etc. & Stencilling nos. No 352.50 383.00
368 RF-004 Fixing Guard Stones in any Soil No 267.50 290.50
Casting STD K.M. Stones with R.C.C. [1:2:4(19 mm) & cement
369 RF-005 No 7,345.00 7,980.00
282.5 KG/Cu.m ] including curing, for "A" and "B" Class Roads
Casting STD K.M. Stones with R.C.C. [1:2:4(19 mm) & cement
370 RF-006 No 4,905.00 5,330.00
282.5 KG/Cu.m ] including curing, for "C" and "D" Class Roads
371 RF-007 Fixing Standard Type K.M. Stones in Any Soil No 2,005.00 2,175.00
Fixing new or Refixing Type Guard stones in Cement Concrete
372 RF-008 [1:3:6(37.5mm) and Cement 219 KG/Cu.m ] With Min. Cover No 949.00 1,030.00
75mmx 300 mm Depth
Casting Standard Type Guard Stones in Concrete [1:2:4(19mm) &
373 RF-009 No 2,500.00 2,715.00
Cement 282.5 KG / Cu.m]
Casting Standard Type Guard Stones in Concrete [G25(19mm)As

374 RF-009A No 3,455.00 3,750.00
per Drawing No T/B/100-Rev 1,For Bridges and Culvers
375 RF-009P Casting Standard Type Guard Stones-Part 1of RF-009A No 7,630.00 8,285.00
376 RF-009Q Casting Standard Type Guard Stones-Part 2 of RF-009A No 833.00 905.00
377 RF-009R Casting Standard Type Guard Stones-Part 3 of RF-009A No 95,119.00 103,319.00
378 RF-010 Rout NumberingWith Reflective Paint on 2 sides No 943.00 1,025.00

Casting Standard Boundary Markers in Reinforced Concrete
379 RF-011 [1:2:4(19mm)] with Admixtures, Including 14 days Curing and No 2,725.00 2,960.00
Loading to Vehicle at Yard (Agg. Transport paid Separately)

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Section 12 - Notic Boards & Road Signs
[SSCM 810.2 AND 1501.3] - All Paints Should
Conform to the Requirements of SLS as Given in
SSCM 1707.
Notice & Traffic Sign Boards Etc. Fixed in Concrete
380 RS-001 [1:3:6(37.5mm) and Cement 219 KG/Cu.m) (Excluding Transport No 1,840.00 2,000.00
of Aggregate)
Cleaning & Whitewashing 2 Coat Town Name Boards (Inc. Tar
381 RS-002 No 469.00 510.00
Skirt)
Cleaning, Painting one Coat & Relettering Etc. Traffic sign Boards
382 RS-003 No 3,040.00 3,300.00
inc. Paint Post in B/W
383 RS-004 Cleaning and painting 1 coat on Notice Board Sq.m 420.00 456.50
384 RS-005 lettering & Numbering Below 50 mm No 78.00 84.75
385 RS-006 Lettering and Numbering 50mm-75mm No 93.50 101.50
386 RS-007 lettering & Numbering 75 mm - 150 mm No 117.00 127.00
387 RS-008 lettering & Numbering 150 mm - 225 mm No 156.00 169.50

Painting 2 Coats Continuous Center Line,100 mm Wide With
388 RS-009 L.m 181.50 197.50
Enamel Paint
Painting 1 Coats Continuous Center Line,100 mm Wide With
389 RS-010 L.m 181.50 197.50
Road Marking Paint (White)
Painting 2 Coats Broken Center Line,100 mm Wide With Enamel
390 RS-011 L.m 172.00 186.50
Paint
Painting 1 Coats Continuous Center Line (Without Reflective
391 RS-012 Studs),100 mm Wide, At 3 meter Intervals With Road Marking L.m 175.50 190.50
Paint (White)
Barricading With Empty (Hot Tar) Barrels Including White Wash(
392 RS-013 No 353.00 383.50
ExcludingTransport) and Cost of Barrels
Revetment to Banks etc. with Empty Barrels in Horizontal Tiers
393 RS-014 No 969.00 1,050.00
with Vertical Batter(1:8) including Transport of Barrels
Road Marking Continuous Center line 100 mm Width, using
394 RS-015 Sq.m 399.00 433.50
Thermoplastic paint (White) , Inclusive Barricading.
Road Marking Standard Pedestrian Crossing, using Thermoplastic
395 RS-016 L.m 832.00 904.00
paint (White) , Inclusive Barricading.

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Section 13 - Miscellaneous
Preparing Stock Piling Premix Using Pen, Grade Bitumen (Excl.
396 MS-001 Cu.m 16,510.00 17,930.00
Transport of Aggregate) (Site Made)
Preparing Stock Piling Premix Using Pen, Grade Bitumen (Excl.

397 MS-001A Cu.m 11,180.00 12,145.00
Transport of Aggregate) (Site Made) with Department Bitumen
Patching Shallow Pot Holes. Depth Less 20mm using hot bitumen
1.2ltr/Sq.m & 12.5mm chips single size @ 13.75 cu. deci m/sq.m
398 MS-002 Sq.m 263.50 286.50
incld. hand tamping (rat. inc. cost of bitumen & mater.) (Excl.
Transport. of Aggregate & Bitumen)
Patching road with premix after preparing surface with 30% cut
399 MS-002A Cu.m 11,750.00 12,760.00
back
400 MS-002B Patching road with premix after preparing surface Cu.m 10,850.00 11,785.00
Patching Shallow Potholes, Depth Less Than 20mm Using 10-20%
Cutback Bitumen 1.2ltr/Sq.m and 12.5mm Chips, Single Size at
401 MS-003 Sq.m 276.00 300.00
13.75 CuDeci m/Sq.m including hand tamping (Excl. Tr. Agg,
Bitumen )
402 MS-003A Patching Shallow Potholes, Part 1 of Item No MS-003 ltr 93.25 101.00
Patching shallow pot holes, depth less than 20mm using emulsion
(Crs1) @ 1.2Ltr/Sq.m & 12.5mm cu.deci m/sqm including hand
403 MS-004 Sq.m 236.50 257.00
tamping transport of emulsion to site etc. Rate include cost of
emulsion and other materials) (Excl. transport of aggregate)
Patching pot holes of Medium ,depth of 20-75mm with Premix

(Site Made) using Cutback 10-20% at the Rate of 83.5 Ltr/Cu.m of
404 MS-005 Sq.m 1,965.00 2,135.00
19mm Down Aggregate including preparation of Surface, Tack
Coat(CSS1) AT .75Ltr/Sq.m, Trimming Sides, Tamping etc
Patching pot holes of Medium ,depth of 20-75mm - Part 1 of the

405 MS-005A Sq.m 242.00 262.50
Item MS-005
Patching pot holes of Medium ,depth of 20-75mm - Part 2 of the
406 MS-005B Sq.m 544.00 591.00
Item MS-005
407 MS-005C Patching Potholes of Medium Depth - Part 3 of Item MS-005 Cu.m 17,600.00 19,120.00
Patching Potholes using Plant Made Premix Bound Including

408 MS-006 Sealing the patching with emulsion (CRS-1) painting @ 7.3 M.ton 15,960.00 17,330.00
ltr/m.ton cover with sand (Transport of premix paid separately)
Patching Potholes of Medium Depth 20-75mm Using Graded

409 MS-007 Aggregate 19-12.5mm With Hot Bitumen 1.75 ltr/Sq.m and Blot. Sq.m 1,045.00 1,135.00
Material at 1 Cu.m/125 Sq.m and .75ltr/Sq.m Tack Coat(CSS-1)
Patching Potholes Deeper Than 75mm Using Premix Material

(Site Made) to a Depth of 37.5mm(Over the Prepared Surface with
410 MS-008 Sq.m 1,125.00 1,220.00
Aggregate and Gravel Paid Separately) Using 10-20% Cutback
83.5Ltr/Cu.m of 19mm down Agg, .75Ltr/Sq.m Tack coat
Patching pot holes more then 75mm deep with water bound gravel
material using 50mm or 12.5 mm single size aggregate along with
411 MS-009 Sq.m 74.50 80.75
useable old aggregate obtain from picking and preparation of
surface inc. laying watering Spreading gravel of approved quality

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Patching Ruts and Depressions Upto 75mm Depth Using Site
412 MS-010 Made Cold Mix (Cut Back) Material With the Surface and Edge Sq.m 1,755.00 1,905.00
Prepared as Per Specifications .75Ltr/Sq.m Tack Coat
413 MS-010A Patching Ruts and Depressions Part 1 of Item MS-010 Sq.m 30.75 33.25
Patching Ruts and Depressions Upto 75mm Depth Using Plant
414 MS-011 Made Cold Mix (Cut Back) Material with .75Ltr/Sq.m tack Sq.m 1,725.00 1,870.00
coat(CSS-1)(Premix paid Separately)
Patching Ruts and Depressions Deeper than 75mm Depth Using
50mm Down Aggregate, Top 40mm with Plant Made Cold Mix
415 MS-012 Sq.m 1,545.00 1,680.00
(Cut Back) Material with .75Ltr/Sq.m tack coat(CSS-1)(Premix
paid Separately)
Patching Ruts and Depressions Deeper than 75mm - Part C of Item
416 MS-012C Sq.m 5,125.00 5,565.00
MS-012
Patching Ruts and Depressions Upto 75mm Deep with .75Ltr/Sq.m
Tack Coat(CSS-1) 50mm Down Aggregate, Hot Bitumen applied
417 MS-013 Sq.m 1,180.00 1,280.00
at 1.75Ltr/Sq.m, Blotting Material at 1 Cu.m/125 Sq.m (Agg. paid
separately)
Patching Ruts and Depressions Deeper Than 75mm with
.75Ltr/Sq.m Tack Coat(CSS-1) 50mm Down Aggregate, Hot
418 MS-014 Sq.m 1,345.00 1,465.00
Bitumen applied at 1.75Ltr/Sq.m, Blotting Material at 1 Cu.m/125
Sq.m (Agg. paid separately)
Correcting and Strengthening Edges of the Road by Cold mix
40mm thick, Cutback 10-20%, at the rate of 83.5Ltr/Cu.m on
419 MS-015 Sq.m 1,915.00 2,080.00
19mm down Aggregate, Over 50mm down Aggregate, Tack coat
.75 Ltr/Sq.m(CSS 1)
Correcting and Strengthening the Edges of Road by Cold mix -
420 MS-015B Sq.m 5,135.00 5,575.00
Part B of the item
Correcting and Strengthening Edges of Road by Cutback(10-20%)
Cold Mix 40mm thick with 83.5Ltr/Cu.m 19mm Down aggregate
421 MS-016 over .75Ltr/Sq.m Tack Coat(CSS-1) over 50 mm down over Sq.m 2,250.00 2,445.00
Closely packed 100mm agg. with excavation width 225mm, depth
225mm
422 MS-016B Correcting and Strengthening Edges Part B of the Item MS-016 Sq.m 2,185.00 2,370.00
Patch Sealing with emulsion painting the surface by spray of crs-1

423 MS-017 @ .75ltr/sq.m squeeing the emulsion and spreading the blotton Sq.m 127.00 138.00
material (Sand) at the rate of 1 Cu.m/125 Sq.m
Patch Sealing with hot Bitumen painting the surface by Using
.75ltr/sq.m squeeging the bitumen and spreading the blotton
424 MS-018 Sq.m 144.50 157.00
material (Sand) at the rate of 1 Cu.m/125 Sq.m (Transport of
bitumen paid separately)
Patch Sealing of Pitted Surface Using Hot Sand Bitumen Mix

425 MS-019 104Ltr/Cu.m of Sand Spread and Hand Tamped Including Sq.m 345.50 375.50
Brushing and Cleaning The Surface (Excl Transport of Bitumen)
426 MS-019A Patch Sealing of Pitted Surface, Part A of Item MS-019A Sq.m 18,660.00 20,270.00
427 MS-019B Patch Sealing of Pitted Surface, Part B of Item MS-019A Sq.m 65.75 71.25
Patch Sealing of Pitted Surface With Emulsion Sand Slurry using

428 MS-020 CRS 1 or 2 at the Rate of 136.5Ltr/Cum of Sand Mix Properly Sq.m 317.00 344.50
Laid, Leveled & Squeeged incl. Brushing and Cleaning
Patch Sealing of Pitted Surface with Sand Emulsion Slurry, Part A

429 MS-020A Sq.m 17,340.00 18,830.00
of Item MS-020A

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Patch Sealing of Pitted Surface, Using Emulsion Sand Slurry, Part
430 MS-020B Sq.m 57.00 62.00
B of Item MS-020A
General upkeep of Road sides Including Maintaining the Right of
way in a Neat Condition by Trimming, Weeding & Clearing of the
431 MS-021 Km 6,850.00 7,440.00
Road Sides, Drains , Drainage Structures, Scupper Drains &
Cleaning Minor Slips
Cleaning ordinary Jungle Including Removing High Growing

Plants and Trees of Girth < 300 mm other than those designated to
432 MS-022 Km 13,820.00 15,010.00
remain. by Uprooting or by Cutting and then uprooting the Stumps
or by Cutting only as Directed (SSCM 1203.2)
Cleaning medium Jungle Including Removing High Growing

433 MS-023 Km 19,170.00 20,830.00
or by Cutting only as Directed
Cleaning heavy Jungle Including Removing all High Growing
434 MS-024 Km 24,520.00 26,640.00
or by Cutting only as Directed
Repairs to Damage of Shoulders verges and Embankments slopes

including making good depressions,ruts,holes and Erosion path
435 MS-025 Cu.m 706.00 767.00
with approved gravelly soil & compacting the same with roller(8-
10 ton) as Directed(Gravel soil be paid separately if brought outsid
Regarding and Regravelling of shoulders with gravel of approved

Quality , duly compacted with Roller (8-10 ton) as directed for
436 MS-026 km 355.00 386.00
Repairing high sides Caused by heaving deposits and Construction
Debris, to Required levels by using a grader (120 -140hp)
Regarding and Regravelling of shoulders with gravel of approved

Quality , duly compacted with Roller (8-10 ton) as directed for
437 MS-027 Repairing high sides Caused by heavings deposits and km 798.00 866.00
Construction Debris, to Required levels manually Gravel (loose
volume)
Replacing Damaged Cracked Concrete Slabs in Foot Walks with

Precast/Cast insitu Concrete 1:2:4(19mm), with 50mm minimum
438 MS-028 Sq.m 2,720.00 2,955.00
thickness including fixing in position with Cement Mortar 1.3 mix
(Excluding Transport of Aggregate) (SSCM 1204.3)
Cutting and Removing Fallen Trees upto 600 mm Girth Including

Cutting into Required number of Pieces Including Disposal as
439 MS-029 No 936.00 1,015.00
Directed. minimum Piece Shall not be less than 2m(SSCM 1203.2)
Cutting and Removing Fallen Trees 600 - 900 mm Girth Including

Cutting into Required number of Pieces Including Disposal as
440 MS-030 No 1,340.00 1,455.00
Directed. minimum Piece Shall not be less than 2m(SSCM 1203.2)
Weeding Masonry Culverts Small Bridges and Retaining Walls

441 MS-031 Culverts 539.00 586.00
(SSCM 1303.3)
Masonry Random Rubble with Boulders including Collect (SSCM
442 MS-032 Cu.m 1,955.00 2,125.00
1006.3(b))
Fixing cats Eyes in Tar Macadam Including Breaking road
443 MS-033 Surface, Barricade etc. [SSCM 810-.3(c)] No 515.00 560.00

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Reducing High Sides in Ordinary Soil [SSCM 301.3/1201.3(c)]
444 MS-034 Cu.m 838.00 910.00
Reducing High Sides in Medium Soil

445 MS-035 Cu.m 1,215.00 1,320.00
Reducing High Sides in Hard Soil

446 MS-036 Cu.m 1,595.00 1,730.00
Reducing High Sides in Soft Rock

447 MS-037 Cu.m 1,975.00 2,145.00
Reducing High Sides in Rock Requiring Blasting

448 MS-038 Cu.m 3,865.00 4,200.00
White Washing 1 Cote to Parapets of Bridges and Culverts (SSCM

449 MS-039 Sq.m 55.50 60.25
1403.3(e))
450 MS-040 White Washing 2 Cotes to Parapets of Bridges and Culverts Sq.m 95.25 103.50
White Washing 1 Cote to Parapets of Bridges and Culverts after
451 MS-041 Sq.m 139.50 151.50
cleaning Attending to minor Repairs
White Washing 2 Cote to Parapets of Bridges and Culverts after
452 MS-042 Sq.m 181.50 197.00
cleaning Attending to minor Repairs
Painting with Emulsion 1 Coat to Parapets of Bridges and
453 MS-043 Culverts, Guard Stones and KM Posts After Cleaning and Sq.m 318.50 346.00
Attending to Minor Repairs [ SSCM 1501.3(a)-(v)]
Painting with Enamel 1 Coat to Parapets of Bridges and Culverts,
454 MS-044 Guard Stones and KM Posts After Cleaning and Attending to Sq.m 332.00 360.50
Minor Repairs [ SSCM 1501.3(a)-(v)]
Painting with Enamel 2 Coats to Parapets of Bridges and Culverts,
455 MS-045 Guard Stones and KM Posts After Cleaning and Attending to Sq.m 525.00 570.00
Minor Repairs [ SSCM 1501.3(a)-(v)]
456 MS-046 Culverts, Guard Stones and KM Posts After Cleaning and Sq.m 515.00 559.00
Attending to Minor Repairs [ SSCM 1501.3(a)-(v)]
457 MS-047 Culverts, Guard Stones and KM Posts Including Preparing Surface Sq.m 243.50 264.50
of Old Work [ SSCM 1501.3(b)-(v)]
Painting Sub Coat Emulsion to Parapets of Bridges and Culverts,
458 MS-048 Guard Stones and KM Posts Including Preparing Surface [SCM Sq.m 213.00 231.00
1501.3(b)-(v)]
Painting 1 Coat Emulsion Paint to Parapets of Bridges and
459 MS-049 Culverts, Guard Stones and KM Posts Including Preparing Surface Sq.m 224.50 243.50
of New Work [ SSCM 1501.3(b)-(v)]
Cleaning & Painting 100mm wide stripe for skirting to guard
460 MS-050 L.m 111.50 121.50
stones. {SSCM 1501.3(b)(v)}
Painting 2 Coats Standard Pedestrian Crossing for Carriageway
461 MS-051 L.m 2,700.00 2,930.00
[SSCM 810.2(c)]
Painting 1 Coat Standard Pedestrian Crossing for Carriageway
462 MS-052 Sq.m 2,780.00 3,020.00
Using Road Marding Paints [SSCM 810.2(c)]
Erecting, Barricading in Jungle Timber 75-100 mm Dia, Vertical
463 MS-053 Posts at .9m Centers and 1.2 Above Ground including White L.m 438.00 476.00
Washing. [SSCM 1709]
Temporary Scaffolding for Painting or Tarring Bridges and for
464 MS-054 Weeding on Bridges or Retaining wall Including Dismantling after Sq.m 167.00 181.50
work. [SSCM 1008.3(a)]
Roughening Existing Smooth tarred Metalled Carriageway by hand
465 MS-055 for Bonding , Collecting Disposal of all Loose Materials [SSCM Sq.m 25.50 27.75
03.3(b)]
466 MS-056 Supply of Diesel for Machineries ltr 120.50 131.00

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Patching road with Premix (Loose Volume) after Prep, Surface
with Emulsion (CSS-1) at .75 ltr/sq.m at tack Coat Including
467 MS-057 Cu.m 7,520.00 8,170.00
internal Transport and Hand Stamping. (Supply of premix (Loose
Volume) Paid Separately) [SSCM 1102.3(b)]
Patching Road With Premix After Preparing Surface With
Emulsion (CSS-1) at .75 ltr/sq.m as Tack Coat, Including Internal
468 MS-058 M.ton 7,590.00 8,245.00
Transport and Stamping with Machine (Supply of Premix Paid
Separately) [SSCM 1102.3(b)(i)]
Painting two Coats Enamel Paint on Kerbs, After Cleaning and
469 MS-059 Sq.m 515.00 559.00
Preparing Surface
Preparing and Stock Piling Premix at Site Using 12.5 mm
470 MS-060 Aggregate and Emulsion (CSS-1) (Excluding Transport of Cu.m 14,435.00 15,680.00
Aggregate)
Breaking Manually Asphalt layer 2"-3" Thick on the Carriageway
471 MS-061 L.m 632.00 686.00
for Kerb Laying

RATE RATE FOR
DESCRIPTION UNIT
3M/Rs. 3M/Rs.
Section 14 - Survey & Day Works
472 SV-001 Supply of Unskilled Labour Days 2,088.00 2,268.00
473 SV-002 Supply of Semiskilled Labour Days 2,320.00 2,520.00
474 SV-003 Supply of Skilled "A" Grade Labour Days 3,480.00 3,780.00
475 SV-004 Supply of Skilled "B" Grade Labour Days 2,900.00 3,150.00
476 SV-005 Clearing jungle (Light) to a Width of 1.22 meters for Survey work km 7,975.00 8,665.00
Clearing jungle (Medium) to a Width of 1.22 meters for Survey

477 SV-006 km 11,815.00 12,835.00
work
478 SV-007 Clearing jungle (Heavy) to a Width of 1.22 meters for Survey work km 15,950.00 17,330.00
479 SV-008 Supply of Labour for Chaining and Cutting Pages and Pegging km 2,215.00 2,405.00
Leveling Chaining and Pegging and Establish Bench Marks on

480 SV-009 km 4,430.00 4,815.00
Concrete Rock or Pegs and Checking Back Levels
481 SV-010 Surveying Including Fixing Pickets & Taking Angles km 4,430.00 4,815.00
482 SV-011 Changing Traverse Lines and Taking off-sets km 5,910.00 6,415.00
Original Item No T1-002,T1-003A,T1-003B,T1-003C,T1-

006,T1-007A & T1-007B are deleted due to non match
Provincial Council Rates.
NOTE:-
Therefore Replaced Provincial Council Rates without
Breakdown the Item No T1-002,T1-003, T1-004, T1-
005,T1-006 & T1-007

IRRIGATIONSCHEDULE
IRRIGATION SHEDULE OF
OFRATES
RATES
2021
PREPARED BY
PROVINCIAL IRRIGATION DEPARTMENT
CONTENTS
IRRIGATION SCHEDULE OF RATES
Page
- i to xii
GENERAL NOTES
- DEMOLISHER -98
SECTION I
- EXCAVATION AND EARTH -98 to 99
SECTION II WORK
- CONCRETE WORKS -100

SECTION III
- MASONRY WORKS -100
SECTION IV
- MISCELLANEOUS / GENERAL -100 to 102
SECTION V
IRRIGATION SCHEDULE OF RATES – 2021
Prepared by Provincial Department of Irrigation, Central Province
 Basic Rates
The basic prices prepared by the Central Provincial price committee 2021 - &
approved by the Deputy Chief Secretary (Engineering Services) are used to prepare
the IRRIGATION RATES- 2021.
 General Notes
The Irrigation Rate is to be read in conjunction with the Standard Specification

issued for irrigation work by the Construction Industry Development Authority
(CIDA) (specification for irrigation and land drainage works-publication
No: SCA/3/1), except where superseded by the notes or the descriptions in the
schedule.
Only those materials which are specially mentioned in the descriptions should be
used and should be the best quality material, confirming to the requirements of the
relevant standard. (SLS or BS)
All the materials & the quality of the material should be approved by the Engineer,
described in the agreement.
Working Rates of this Irrigation Rate are calculated as follows
 Working Rates = Basic Rates + Overheads & Profit Margin.

 Overheads & Profit margin is taken as 16 % of the basic rates for
Total Cost Estimate is above 10 million.
 Overheads & Profit margin is taken as 26 % of the basic rates for
Total Cost Estimate is below 10 million.
Where,
 Overheads – 6 % for Total Cost Estimate is above 10 million.
 Overheads – 16 % for Total Cost Estimate is below 10 million.
i
 Profit margin – 10 %
Following are the breakup of overheads
For Total Cost Estimate is above 10 million
General overheads
1. Head office and rent, lights, telephone, stationery suppliers,
furniture etc. for same 0.6 %
2. Salaries of Head office Manager, Engineers, Technical assistances,
Draughtmen, Clerks, Stenos, Typists, Minor staff and Drivers 1.2 %
3. Transportation and subsistence of head office staff 1.0 %
4. Insurance, interest, and taxes on business 0.4 %
5. Legal expenses and consultancy fees 0.2 %
6. Workshop and yard rents, sheds, garages and supplies 2.2 %
7. Salaries of workshop and yard storekeepers, drivers,
foremen, mechanics and workmen 0.4 %
Total 6.0%
For Total Cost Estimate is Below 10 million

Site overheads
1. Supervision of work (wages of work supervisors) 1.0 %
2. Supervision of labour (wages of gangers) 4.0 %
3. Temporary works:
a. Access road & maintenance 0.2 %
b. Site building for accommodation of part labour 0.7 %
c. Central stores building 0.6 %
d. Fencing and Protection 0.3 %
e. Provision of water, Lights etc. 0.3 %
f. Clearing & Tidying up 0.2 %
g. Collection of materials including 0.4 %
Cement & steel
4. Watchers for field stores and security of sites 0.8 %
5. Tools and implements for miscellaneous work 0.9 %
6. i. Setting out and measurements 0.5 %
ii. Providing sample of testing 0.2 %
7. Transportation of supervisory staff 1.0 %
8. Job office, furniture, stationary, suppliers, water, lights etc. 0.9 %
ii
9. Wages of job office staff 1.2%
10. Transportation of job office staff 0.4 %
11. i. Bonds for bid performance and fidelity Guarantee 0.3 %
ii. Insurance of work and workmen’s compensation 0.5 %
12. Interest in Capital Investment 1.6 %
Total 16.0%
Method of Measurement
The Bill of Quantities have been generally prepared in accordance with principles of the
Standard Method of Measurements for Building works in Sri Lanka (SLS 573 1999)
I. Head transport rates given in Irrigation Rate have to be taken for slope angle less than 20º
in hilly areas, when the slope angle exceeds 20º the head transport to be referred to central
provincial price committee report 2021. However, considering site condition, Engineer can
decide the necessary Head transport.
II. A Confidential document and to be used for Central provincial council work only.
III. This document to be used for estimation purpose only.
IV. Additional rates should be prepared for any item deviate from the description or not listed
based on Irrigation Rate analysis/work study.
SI – British conversion factors
Mass 1kg 2.204 lb

Length 1m 3.281 ft
1 Cu.ft. 0.028 m3
1 Sqrs 9.290 m2
1 cu 2.831 m3
1 sq.ft. 0.092 m2
1 lb. 0.453 kg
1 c.w.t. 50.802 kg
1 gal 4.546 l
iii
EXCAVATIONS
3 .4 Excavation and Preparation of Foundation for Structure
Except as otherwise shown on the drawings or prescribed by the Engineer, open cut excavation for
foundations shall be made to the outlines and dimensions of the structures for which the foundation
is required. The Contractor shall make his own allowances for lateral excavations outside the limits
shown for foundations of the structure. Blasting operations for rock excavations shall be subject to
the requirements in clause 3.6. It shall be the responsibility of the Contractor to maintain the
stability of the excavated faces during construction by acceptable methods.
Excavated material shall be dumped sufficiently clear of the edges of excavation. The disposal of
excavated material shall be as described in Clause 3.7. Finishing of excavated surfaces shall be
done to the satisfaction of the Engineer so as to provide firm foundation upon or against which the
concrete or masonry is to be placed. Compaction of foundation by an approved method may be
required as directed by the Engineer. Rock excavation may require special blasting procedure such
as cushion blasting or pre- splitting as approved by the Engineer to ensure sound, unsheltered rock
after excavation. After blasting, scaling and trimming shall be done to remove slugger, weathered
and dummy rock and the loosened rock shall be removed by chiseling, picking, sledging and
barring. The final rock foundation surfaces shall present a rough outline and shall be free from steep
angles and sharp projections.
3.2 Excavation of Foundation for Dam Embankment
After preparation of the entire area to be occupied by the dam as described in Clause 5.1, a cut-off
trench shall be excavated in the dam embankment foundation to the established lines and grades as
shown on the drawings and /or as directed by the Engineer and all unsatisfactory and loose material
shall be removed to the extent directed by the Engineer. The removal of boulders may be required.
Disturbed foundation at the established level shall be corrected by approved compaction so that the
foundation has a dry unit weight not less than that in the disturbed condition. The longitudinal
slopes of the excavated trench in common material shall not be steeper than 3 horizontal to 1
vertical.
Rock excavation may require special blasting procedures such as cushion blasting or pre-splitting as
approved by the Engineer to ensure sound un-shattered rock after excavation to required level.
Accurate trimming of the slopes of excavations will not be required, but the other operations
described in Clause 3.6 to be done as closely as practicable to the established lines and grades.
The rock foundation shall not have a slope greater than the angle of friction of the rock neither
along nor across the dam axis. Where slopes are steep, the rock shall be benched to give near
horizontal seating, the benches themselves having downward slopes of 1:10 towards the upstream.
The alignments and cross-sectional dimensions shown on drawings will be subject to change by the
Engineer to adopt the foundation to the conditions disclosed by the excavation.
iv
3.3 Excavation for Canals
Canals shall be excavated to the specified width, depth, side slopes and gradient shown on the
drawing and/or established by the Engineer and shall be finished uniformly to the prescribed lines.
Rock excavation may require special blasting procedure such as cushion blasting or pre-splitting as
approved by the Engineer to ensure sound, un-shattered rock after excavation. In so far as
practicable, the finishing operations after blasting as described in Clause 3.6 required on canals.
MATERIALS
4.1 Source of Materials
When drawings identifying borrow areas and/or quarries are not furnished by the Engineer, the
Contractor shall submit for the approval of the Engineer his proposals for the sources of
construction materials complying with these specifications. Approval of any borrow area/quarry
shall not be considered as approval of all excavations from the borrow area/quarry. Each part
excavated from the approved borrow area/quarry shall be subject to further approval by the
Engineer.
4.2 Location of Borrow Areas
The location of any borrow area shall be subject to the requirements given below.
i. Borrow areas, as far as possible, shall not be located on the downstream of the dam.
ii. Borrow area located near the dam, shall be at a distance not less than three times the height
of the dam between the toe of the dam and edge of the borrow area.
Borrow areas adjacent to primary canals shall be located within the canal reservation adjacent to the
Operation and maintenance bund road/road reservation so that such borrow area could be connected
to function as road drains. Borrow areas may also be located on high ground in the vicinity of the
secondary and tertiary canals.
iii. Borrow area located other than as specified in (a) and (b) above shall be at the shortest
possible haul distance.
v
Table 1
Grading and Plasticity Limits for Earth Embankments
Zone Characteristics Absolute Minimum Absolute Maximum
Low Permeability Passing

75 micron sieve % 30 70
Liquid Limit % 20 50
Plasticity index % 08 30
Medium or High Passing

Permeability
75-micron sieve % - 70
0.36 mm sieve % 08 -
2.36 mm sieve % 50 -
25 mm sieve % 100 100
Liquid Limit % 0 50
Plasticity index % 0 30
4.7.2 Tests on Gravel
Materials from approved gravel quarries shall be tested periodically for the following
characteristics:
i. Mechanical Analysis ii. Atterberg Limits
4.7.3 Test on Sand
Materials from approved sand quarries shall be tested periodically for the following characteristics.
i. Gradation ii. Specific Gravity iii. Organic Content
4.7.4 Test on Rock
Rock samples from approved quarries shall be tested periodically for the following characteristics.
i. Gradation ii. Specific Gravity
iii. Los Angeles Abrasion Test iv. Sodium or Magnesium Sulphate Soundness Test
vi
5.4 Turfing
After the slopes of the embankment have been dressed to line they shall be scarified in the locations
to be turfed. Where required a surface dressing layer of approved top soil shall be placed on the
scarified slopes to an approved thickness. The surface prepared shall be covered with layers of turf
sod consisting of squared not exceeding 300 mm square of dense living grass-growth of approved
species. The sod shall be carefully handled during transportation to minimize loss of earth. The
squares of turf shall be laid on the required locations in close contact to the required pattern which
may consist of strips, squares, parallelograms, etc. and then tamped firmly in place. Immediately
after placing, the turfed slopes shall be watered and kept moist until plant growth has been re-
established.
REINFORCEMENTS AND DOWELS
9.1 Reinforcement
This section is covered in the Specifications for Buildings Works Vol. I and reference should be
made to same.
9.2 Dowels for Structures
Dowels shall consist of steel bars described in Clause 9.1 and shall be of the size length and shape
shown on the drawings or as directed. Dowels shall be fixed in the locations and to depths in holes
in foundations and / or concrete as shown on the drawings or as directed.
Holes shall be drilled to receive the dowels. The diameter of the hole shall be between 1.25 to 1.5
times the diameter of the dowel bar. After drilling, the holes shall be washed and cleaned
immediately prior to filling with grout or cement – sand – mortar mixed to the consistency and
proportions specified in the drawings or as directed. The dowel bars shall be thoroughly cleaned and
forced into place in the grout before the initial set of the grout and the dowel bars shall be vibrated
or rapped until the entire surface of the embedded portions of the dowel bars are in intimate contact
with the grout. Special care shall be taken to ensure against displacement of the dowel bars until the
initial set of the grout.
10.6 Concrete Construction
10.6.1 General
All concrete Construction shall conform to Clauses 10.1 to 10.5 inclusive and to the following
requirements for the more important types of concrete Construction. All structures shall be built to
the prescribed lines, grades and dimensions. The location of all Construction joints shall be subject
to approval. All timber, metal or other accessories necessary for the completion of the structure as
shown on the drawings or as directed shall be placed and attached. The cost of such work, for which
vii
specific unit prices are not provided in the bill of quantities, shall be included in the unit prices bid
for the work to which they are appurtenant.
The dimensions of each structure shown on the drawings will be subject to such changes as may be
found necessary by the Engineer to adapt the structure to any new information or newly disclosed
conditions resulting from excavation, from hydraulic model studies, from changes in equipment,
and from further design consideration by the Engineer that unit costs will be increased or decreased
as a result of such changes. A new unit price will be made for such increase or decrease in cost in
accordance with the General Conditions. Sequence of sections being Constructed shall be as
approved by the Engineer, and shall be such as to avoid initial stressing of reinforcement.
10.6.2 Concrete in Dams (Retaining Walls & Irrigation Structures)
Forms for surfaces between adjacent blocks of the dam may be removed as soon as the concrete has
hardened sufficiently to prevent surface damage. The placing of concrete in the dam shall conform
to the requirements in Clause 10.6.1.2. Every effort shall be made to affect a regular, periodic
placement of successive lifts throughout the dam.
Concrete shall be deposited under water by approved bottom discharging water-tight containers or
funnel shapedtremieswhich shall be kept continuously full with concrete up to a level above the
water and which shall have the discharging bottom immersed in the concrete with the water. Special
care shall be taken to avoid segregation.
Supports and shoring for concrete overhangs shall remain in place unit all concrete below and
adjacent to the overhang is at least 14 days old.
Vertical contraction joints in the concrete of the dam will be provided for convenience in
construction and to provide for contraction of the concrete. The joints shall be constructed in
accordance with the drawings unless otherwise directed by the Engineer.
Fillets, projections, steps and similar features which are placed monolithically with concrete in the
dam and which are not covered specifically for payment elsewhere in these specifications will be
measured and paid for as concrete in dam.
10.6.4 Concrete in Canal Lining
Concrete in canal lining shall be done to the lines, grades and thickness shown on the drawing or as
directed by the Engineer. The thickness of the lining specified shall be considered as the minimum
thickness. Unless otherwise directed, forms shall not be required for the concrete lining on slopes
where the side slopes of the canal are 1 vertical to 1 horizontal or flatter. The concrete lining shall
be placed inside the design cross- sectional dimensions of the canal. Contraction joints specified in
clause 10.5.3 shall be required where fixed structures intersect the canal lining.
The bottom and side slopes of the canal, in material other than rock, shall be finished accurately to
the dimensions shown on the drawings or as directed, any over-excavations, weathering, runnels,
viii
etc. beingback filled with approved material similar to the natural in – place soils. Large over brakes
in rock excavation may be filled with an approved free-draining material to restore the cross –
section of the canal to the required dimensions. In other respects, the preparation of surfaces shall
conform to the requirements in specification for buildings. If blanket filter is specified, then the
blanket filter shall be placed upon the prepared surfaces and the material shall be moistened with
water immediately before placement of concrete. Filter drains if required shall be constructed before
placement of blanket filter and if blanket filter is not specified along with filter drains, the filter
drains shall be conditioned as for blanket filter immediately before placement of concrete.
Placement of concrete shall conform to the requirements in Para 10.6.1.3 except that forms shall be
used where shown on the drawings or as directed by the Engineer. Transverse grooves shall be
provided by cutting grooves on the surface of the lining while the concrete is still plastic, spaced 3.5
to 4.5 m apart or as shown on drawing or as directed by the Engineer. The depth of the grooves
shall be between 2.5 to 3.0 mm and the bottom width between 1.0 to 1.25 mm.
RUBBLE MASONRY
11.1 Materials for Rubble Masonry
Stones for all masonry work shall be obtained from quarries approved by the Engineer and shall be
the best quality obtainable. Stones shall be free from imperfections such as cracks, sand holes, veins
and laminations. Stones shall be clear grained, dense, heavy, durable and hard. Granite, basalt,
quartzite and limestone are suitable for masonry work.
Stones for rubble masonry shall be flat bottomed and not less than 150mm deep in any part and
225mm wide. The average thickness of individual stones may vary between 150mm to 225mm.The
percentage of smaller stones shall not be more than 25%.
Cement sand and mortar shall conform to the requirements in the specifications for Building works
Vo1 I.
11.2 Mortar
Unless otherwise specified by the Engineer, the mix proportions for the mortar shall consist of 1
part of cement to 5 parts of sand by volume. The mortar shall have a dry consistency.
11.3 Rubble Masonry Construction
All stones used in rubble masonry shall be cleaned and wetted before use to ensure bonding to the
mortar. Surface area of individual stones shall be about 0.3m2 varying in depth between 150 to
225mm. Every stones shall be set flush in mortar, leaving no dry work or hollow spaces. The stones
shall be laid on their flat face, using the larger stones for the foundation courses. Smaller stones not
exceeding twenty five percent of the larger stones shall be carefully selected to roughly fit the
ix
spaces between the larger ones. Chips and spalls shall be wedged into the spaces between the
different sizes of stones, where necessary, to prevent thick beds of mortar. Rolling or sledging of
heavy stones on the surface of recently laid.
11.4 Rubble Pitching Construction
Rubble pitching construction for protection of earth slopes of canals and ramps of causeways from
erosion shall consist of quarried rock bonded together with cement – sand mortar of specified mix
proportion, constructed as lining of specified minimum thickness shown on the drawings or as
directed by the Engineer.
The surfaces of the earthwork to be protected with rubble pitching shall be first finished to the
prescribed slopes, any weathering, runnels etc. being backfilled with approved material similar to
the in –place soils. The surfaces so prepared shall be moistened with water, if required, and tamped
or rolled to the satisfaction of the Engineer.
The materials and mortar for rubble pitching shall conform to the requirements in Clause 11.1 and
11.2 respectively. Stones for pitching shall conform as far as possible to the dimensions in Clause
11.3 The stones shall be laid and hammered down on the prepared surfaces of the earthwork,
approximately plane but not smooth. The stones shall be hand – packed in such a manner that joints
between stones can be completely filled with cement – sand mortar. Stones with overhanging joints
shall not be allowed. The sides and top and bottom edges shall be left as wedges. The “bushings” or
protuberances of stones shall not project more than 15mm from the slopes of the joints. The rubble
pitching shall be finished to the prescribed slopes, the permissible tolerance being 25mm in a length
of 3 m. The finished surfaces of the pitching shall be planes without depressions or protuberances.
The rubble pitching shall be cured with water for a period of at least three days commencing from
the time of the final setting of cement.
11.5 Rip-rap Construction
Rip-rap construction for protection of earth slopes of canals shall consist of quarried rock
constructed as a lining of specified minimum thickness shown on the drawings or as directed by the
Engineer.
x
LIGHT DUTY GATES AND HOISTS
12.1 General
The gates and hoists required in Gated Regulators and Turnouts are considered in these
specifications as Light Duty Gates and Hoists. The Engineer will furnish the drawings for the
fabrication and manufacture of Light Duty Gates and Hoists. However, alternate drawings for
approval of the Engineer may be submitted, which shall show design features better than or equal to
those in the drawings furnished by the Engineer.
In the submission of alternate drawings, 3 prints shall be furnished, one of which will be returned
marked “APPROVED” or “APPROVED EXCEPT AS NOTED” or “RETURNED FOR
CORRECTION”. The fabrication and manufacture of the gates and hoists shown on drawings
marked “APPROVED” or “APPROVED EXCEPT AS NOTED” shall be proceeded with subject to
any corrections and / or exceptions indicated on the drawings. On drawings marked “RETURNED
FOR CORRECTION”, all observations on the drawings and /or in comments of the drawings shall
be attended to and 3 prints of new drawings submitted for approval in the same manner as the
original submission.
In the event the alternate proposals approved by the Engineer involve less cost, an adjustment in
price shall be made in favor of the Engineer at the time of granting the approval. The required gate
together with the specified hoist of same shall be made as shown on the approved drawings and
installed in the locations shown on the drawings or as directed by the Engineer.
REPAIRS AND MODIFICATIONS TO EXISTING CANAL
STRUCTURES AND OTHER RELATED ITEMS
15.1 General
Where structures are to be repaired or modified they shall first be cleared of all silt, stones,
vegetation and rubbish. No separate payment will be made for this operation, the costs of which
shall be deemed to be covered in the rates for other work.
15.2 Dealing with Water
Where it is required the contractor shall carry out all operations required for dealing with water in
conformity with Chapter – 2.
xi
15.4 Demolition of Existing Concrete/Rubble Masonry Structures
Where part of an existing brickwork masonry or concrete structure is to be demolished the

Contractor shall carry out the demolition in such a manner as to avoid damage to the remaining part
of the structures. All waste materials resulting from the demolition shall be transported across the
canal embankment. Any gates, hoists and associated metal works including built-in parts, shall be
carefully removed avoiding damage: if ordered by the Engineer. Any concrete pipe shall be
carefully removed to avoid damage and taken to a location to be notified by the Engineer. Any part
of the remaining structure which has been damaged, holed, or cracked by the demolition work shall
be reinstated to its original condition to the satisfaction of the Engineer, and the final surface or
cross section shall be finished tidily to the satisfaction of the Engineer.
Measurement for payment shall be by volume as determined by the Engineer. Payment shall be
made at the unit rate bid per cubic meter or demolition of brickwork or masonry, mass concrete or
reinforced concrete as the case may be. These rates shall be deemed to include to the costs of all
operations described above except for the removal of gate frames and hoists etc. and concrete pipes.
The removal of gate frames and hoists shall be paid for in accordance with the unit rate bid per
kilogram.
15.5 Raising Existing Concrete Canal Linings
Existing Concrete Canal Lining shall be heightened with in –situ mass concrete as shown on the
Drawings. The top of the existing lining shall be exposed as required and the joint surface prepared
in accordance with Clause 10.5 hereof. The in –situ mass concrete shall be placed and compacted
with suitable formwork to both vertical faces in accordance with Chapter - 10 hereof as appropriate.
After curing and setting, compacted fill shall be placed around the lining to the required level in
accordance with Clause 3.5 hereof.
Measurement for payment shall be made by volume of concrete as shown on the Drawings or
directed by the Engineer. Payment shall be made at the unit rate bid per cubic meter of mass
concrete in raising canal linings which rate shall be deemed to cover the costs of exposing and
preparing the surface of the existing linings as required and of formwork. Filling around the lining
above the existing embankment level shall be paid for separately.
15.6 Clearing and Trimming Existing Canals
Where ordered by the Engineer, existing canals and structures shall be cleared of all loose stones
rubbish and weed growth below full supply level.
Grass and other sort of annual vegetation on the canal banks within the reservation shall be cut
down completely. Local irregularities in the bed and banks shall be trimmed and the material spread
to give a tidy appearance, and local slippage in the banks shall be trimmed and the slope reduced to
render them stable.
Unless otherwise directed by the Engineer, where the banks are stable the slopes shall not be
reduced to conform to the standard cross- sections shown in the drawings, and care shall be taken
not to remove the vegetation cover completely if this could result in instability. All waste materials
resulting from clearing shall be burnt and / or transported and placed beyond the toe of the outside
side slope of canal embankment used as roadway or as directed by the Engineer.
xii
IRRIGATION SCHEDULE OF RATES - 2021
RATE FOR
RATE FOR
SE. ITEM TCE
NO. NO. BELLOW
3M/Rs.
3M/Rs.
SECTION I - CIR - DEMOLISHER

Demolishing and removing collapsed concrete
1 CIR 001 lining 30 m away from reservation m³ 3,099.00 3,366.00
SECTION II - DIR - EXCAVATION AND

EARTH WORK
Earth excavation for foundation or quarry materials
2 DIR 001 and haul the surplus materials up to 30m by m³ 1,940.00 2,110.00
Manually.
Gravel excavation for foundation or quarry materials
3 DIR 002 and haul the surplus materials up to 30m by m³ 2,170.00 2,355.00
Manually.
Common excavation for foundation or quarry
4 DIR 003 materials and haul the surplus up to 30m by m³ 2,170.00 2,355.00
Manually.
Soft rock excavation for foundation or quarry
5 DIR 004 materials and haul the surplus up to 30m by m³ 3,350.00 3,640.00
Manually.
Earth excavation for foundation or quarry materials
and haul the surplus materials up to 30m. by
6 DIR 005 m³ 180.00 195.00
Machinery. (This rate is excluding of transporting of
machinery)
Gravel excavation for foundation or quarry materials
and haul the surplus materials up to 30m. by
7 DIR 006 m³ 205.00 220.00
Machinery. (This rate is excluding of transporting of
machinery)
Common excavation for foundation or quarry
materials and haul the surplus materials up to 30m.
8 DIR 007 by Machinery. (This rate is excluding of transporting m³ 190.00 210.00
of machinery)
Soft rock excavation for foundation or quarry

materials and haul the surplus materials up to 30m by
9 DIR 008 Machinery. (This rate is excluding of transporting of m³ 265.00 285.00
machinery)
Earth excavation for Canal or Tank and haul the

surplus materials up to 1.6 km distance by
machinery)
Gravel excavation for Canal or Tank and haul the

machinery)

RATE FOR
RATE FOR
SE. ITEM TCE
NO. NO. BELLOW
3M/Rs.
3M/Rs.
Common excavation for Canal or Tank and haul the
machinery)
Soft rock excavation for Canal or Tank and haul the

machinery)
Dry Silt removing from Canal or Tank beds and haul

the surplus materials up to 1.6 km distance by
14 DIR 013 m³ 250.00 275.00
machinery.(This rate is excluding of transporting of
machinery)
Wet Silt removing from Canal or Tank beds and haul
the surplus materials up to 1.6 km distance by
15 DIR 014 m³ 335.00 365.00
machinery.(This rate is excluding of transporting of
machinery)
Dry Silt removing from Canal or Tank beds and haul
16 DIR 015 the surplus materials up to 30m. distance by m³ 1,845.00 2,000.00
Manually.
Stripping top soil and including cut and lift up to
17 DIR 016 1.5m and haul 30m distance by manually m³ 1,640.00 1,780.00
Forming tank bund manually (The ratewithout the

18 DIR 017 cost of filling material and the transport) m³ 465.00 505.00
Forming canal bund manually (The rate without the

19 DIR 018 cost of filling material and the transport) m³ 435.00 470.00
Forming tank bund machinery (This rate is excluding

20 DIR 019 m³ 30.00 35.00
of transporting of machinery)
Forming canal bund machinery (This rate is
21 DIR 020 m³ 25.00 25.00
excluding of transporting of machinery)
Cutting & planting turf (The rate without transport)
22 DIR 021 m² 150.00 165.00
Watering turf (The rate without cost of water and the

23 DIR 022 transport) m² 2.50 2.50
Construction of puddle core wall including making

24 DIR 023 m³ 2,711.00 2,945.00
puddle (without transport)
Benching of tank bund slopes to receive new earth
25 DIR 024 average 150mm in depth m³ 1,033.00 1,122.00
SECTION III - FIR - CONCRETE

WORKS
1:3:6 concrete manual mix (The rate without the
26 FIR 001 transport of materials) m³ 17,800.00 19,335.00
1:2:4 concrete manual mix (The rate without the

27 FIR 002 m³ 19,955.00 21,675.00
transport of materials)
1:1½:3 concrete manual mix (The rate without the
28 FIR 003 transport of materials) m³ 20,950.00 22,755.00

RATE FOR
RATE FOR
SE. ITEM TCE
NO. NO. BELLOW
3M/Rs.
3M/Rs.
1:3:6 concrete with concrete mixer (The rate without
29 FIR 004 the transport of materials) m³ 13,835.00 15,030.00
1:2:4 concrete with concrete mixer (The rate without

30 FIR 005 the transport of materials) m³ 15,990.00 17,370.00
1:1½:3 concrete with concrete mixer (The rate

31 FIR 006 m³ 16,985.00 18,450.00
without the transport of materials)
Plywood form work including making, fixing &
32 FIR 007 m² 2,545.00 2,765.00
removing
Swan timber form work including making, fixing &
33 FIR 008 removing m² 2,575.00 2,795.00
Cutting, Bending & Placing mild steel reinforcement

34 FIR 009 bars kg 280.00 305.00
Cutting, Bending & Placing tor steel reinforcement

35 FIR 010 bars kg 275.00 300.00
Supplying and fixing mild steel dowels 20mm dia. &

36 FIR 011 nr 926.00 1,006.00
450mm long
SECTION IV - GIR - MASONRY
WORKS
150mm x 225mm Random Rubble masonry work in
37 GIR 001 1:5 cement and sand mortar in structures m³ 13,181.00 14,318.00
Dry rubble packing (rubble size over 225mm)

38 GIR 002 m³ 2,763.00 3,001.00
225mm thick pitching in 150mm-225mm rubble in
39 GIR 003 1:5 ct.mt. lift m² 1,036.00 1,125.00
12.5mm thick rough ct.plaster in 1:3 cement sand

40 GIR 004 mortar semi rough finish(UR55) m² 650.00 706.00
SECTION V - YIR - MISCELLANEOUS /

GENERAL
Shrub jungle clearing with vegetation, thorny bushes,
undergrowth and less than 100 trees up to 300mm
41 YIR 001 girth, and few isolated trees of less than 600mm girth ha 51,560.00 56,000.00
including cutting uprooting and heaping on approved
places Manually.
Light jungle clearing with vegetation, thorny bushes,
places Manually.
Medium jungle clearing with vegetation, thorny
bushes, undergrowth and less than 500 trees up to
43 YIR 003 300mm girth, and few isolated trees of less than ha 273,300.00 296,800.00
1200mm girth including cutting uprooting and
heaping on approved places Manually.

RATE FOR
RATE FOR
SE. ITEM TCE
NO. NO. BELLOW
3M/Rs.
3M/Rs.
Common jungle clearing with vegetation, thorny
44 YIR 004 300mm girth, and few isolated trees above 1800mm ha 345,400.00 375,300.00
girth including cutting uprooting and heaping on
approved places Manually.
Heavy jungle clearing with vegetation, thorny bushes,
girth, and few isolated trees of above 150mm girth
45 YIR 005 including cutting uprooting and heaping on approved ha 386,700.00 420,000.00
places
Manually.
Shrub jungle clearing with vegetation, thorny bushes,
places Machinery.
Light jungle clearing with vegetation, thorny bushes,
places Machinery.
Medium jungle clearing with vegetation, thorny
heaping on approved places Machinery.
Common jungle clearing with vegetation, thorny
heaping on approved places Machinery.
Heavy jungle clearing with vegetation, thorny bushes,
50 YIR 010 girth, and few isolated trees above 1800mm girth ha 205,400.00 223,100.00
places Machinery.
51 YIR 011 Providing sand bags for coffer dam nr 110 119
75mm tk. Stop planks (kumbuk ) with 10mm dia.
52 YIR 012 2nos. M. S. Iron hooks and applies 2 coats of hot m³ 410,518.00 445,904.00
tar.
75mm tk. Stop planks (milla, mee) with 10mm dia.
53 YIR 013 2nos. M. S. Iron hooks and applies 2 coats of hot m³ 157,102.00 170,649.00
tar.
Scarifying existing rock or concrete surface
54 YIR 014 m² 276.00 300.00
Heavy jungle clearing along survey lines 1200mm -
55 YIR 015 0mm wide rate per 1.6 km (0.48 Acs) km 14,892.00 14,892.00

RATE FOR
RATE FOR
SE. ITEM TCE
NO. NO. BELLOW
3M/Rs.
3M/Rs.
Medium jungle clearing along survey lines 1200mm -
Light jungle clearing along the survey lines 1200mm -

Shrub jungle clearing along the survey 1200mm -

Chaining including of cutting jungle pegs and

59 YIR 019 pegging km 3,416.00 3,416.00
Leveling every 30m chain pegs and establishing

60 YIR 020 B.M.on rock and checking back km 5,124.00 5,124.00
Surveying including fixing angle pickets and taking

61 YIR 021 angle km 6,832.00 6,832.00
62 YIR 022 Chaining traverse lines and taking offsets km 4,919.00 4,919.00
Detail site surveys including spot levels chaining
pegging and establishing B.M. these surveys are
63 YIR 023 nr 26,840.00 26,840.00
breaches spills etc.witch should not exceed 150m ×
150m
Marching pay = 1 unskilled labour day for 4.8 kms.
64 YIR 024 km 373.00 373.00

ANNEX – 01
Drawings
No Description Drawing No
1 Type plan of G.I Pipe flag post -Type 01 CPC/CS/11/04/2017/TYPE - ST/02(i)

2 Type plan of G.I Pipe flag post -Type 02 CPC/CS/11/04/2017/TYPE - ST/02(ii)
3 Type plan of shoring for excavation up to 3.0mm height , CPC/CS/l 1/04/2017/TYPE - ST/03
4 Type plan for Barbed wire fence ( 7 Stands) CPC/CS/11/04/2017/TYPE - ST/05
5 Type plan for Barbed wire fence (10 Stands) CPC/CS/11/04/2018/TYPE - ST/12
6 CPC/CS/11/04/2017/TYPE - ST/10
Type plan for Casting & Erecting fence post ( 1.7 m High)
7 CPC/CS/11/04/2018/TYPE - ST/11
Type plan for Casting & Erecting fence post (2.25m High)
8 Type plan for pre fabricated chain link fence CPC/CS/11/04/2017/TYPE - CLF/01
9 Type plan for Perforated pipe in Retaining wall CPC/CS/11/04/2017/TYPE - ST/04

10 Type Plan of Manhole (600«600«600) CPC/CS/11/04/2018/TYPE - MH/01
11 Type plan of Manhole (1.05«0.675«6) CPC/CS/11/04/2018/TYPE - MH/02
12 Type Plan of Soakage pit 4-0M ( Loose soil) (folly built 1.2m) CPC/CS/11/04/2018/TYPE - SP/03
13 CPC/CS/11/04/2018/TYPE - SFVCM
Type Plan of Soakage pit 4-0H ( Hard soil) (Semi built 1.2m)
14 CPC/CS/11/04/2018/TYPE - SP/05
Type Plan of Soakage pit 6'-0" ( Loose soil) (Fully built 1.8m)
15 Type plan of septic tank for 30 person (Brick) CPC/CS/11/04/2018/TYPE - SEPT/01 -(i)：
le CPC/CS/11/04/2018/TYPE - SEPT/01 -(ii)

Type plan of septic tank for extra over 30 person (Brick)
17 Type plan of septic tank for 50 person (Brick) CPC/GS/11/04/2018/TYPE - SEPT/01 – (i)
18 CPC/CS/11/04/2018/TYPE - SEPT/01 -(ii)

19 Type plan of septic tank for 100 person (Brick) CPC/CS/11/04/2018/TYPE ■ SEPT/01 -(i);
20 CPC/CS/11/04/2018/T¥PE - SEPT/01 -(ii)

21
Type plan for Security weld mesh door with locking device CPC/CS/11/04/2017/TYPE - ST/06
22 Type plan for security weld mesh in open type building CPC/CS/11/04/2017/TYPE - ST/07
23 Type plan for special security grill fixed to Aluminium CPC/CS/11/04/2017/TYPE - ST/08
windows
iK
24 Type plan for special security grill fixed to windows CPC/CS/11/04/2017/TYPE - ST/09
25 Detail of web truss - Type 1 CPC/CS/11/04/2018/TYPE - TR/01 (i),(ii)

Detail of web truss - Type 2 CPC/CS/11/04/2018/TYPE - TR/02 (i),(ii)
Detail of web truss - Type 5 CPC/CS/11/04/2018/TYPE - TR/05 ⑴,(ii)
26 Type plan of truss for span 20丨.0"-30’.0" ( Space of truss 15'- CPC/CS/11/04/2018/TYPE - ITR/02/1,2,3 ,
20)
27 Type plan of truss for span 30,.0,,-40,.0H ( Spacing of truss 15- CPC/CS/11/04/2018/TYPE - ITR/04/1,2,3
20)
Type plan of truss for span 20’.0"-30’.0" ( Spacing of truss
28
<15’） CPC/GS/11/04/2018/TYPE - ITR/01/1,2
29 Type plan of truss for span 30,.0,,-40,.0,* ( Spacing of truss CPC/CS/11/04/2018/TYPE - ITR/03/1,2
<15')
30 Aluminium partition drawings

BARBED WIRE FANCE
NOTE :-
1.No of Strands = 07
2.For detail of Fence Post
REFER DRW NO
CPC/CS/11 /04/2017/TYPE-ST/10
140mm
100
180
180
180
1700
300
150
2400
DRAWN BY- NISHANI SCALE- NTS DRG. NO.-CPC/CS/ 11/ 04 /2017/TYPE-ST/05

DEPARTMENT OF ENGINEERING SERVICES TYPE PLAN DESIGNED BY- Eng. A.G.SAMARASINGHE DATE - 01-11-2017
CENTRAL PROVINCE, FOR CHECKED BY-
KANDY BARBED WIRE FANCE
DETAIL DRAWING
DEPUTY PROVINCIAL DIRECTOR (Eng. Services) PROVINCIAL DIRECTOR

BSR ITEM- G-014 PLANNING (ENGINEERING SERVICES)
BARBED WIRE FANCE
NOTE :-
1.No of Strands = 10
2.For detail of Fence Post
REFER DRW NO
CPC/CS/11 /04/2018/TYPE-ST/11
140mm
100
2250
310
150
2400

KANDY BARBED WIRE FANCE
DETAIL DRAWING

CASTING & ERRECTING FENCE POST
100
100
4R6
140
180
14BWG wire stirrups

180
at 150mm c/c
with grade 25 concrete
SECTION X-X
180
180
1700
180
180
X X
480
150
150
DRAWN BY- NISHANI SCALE-NTS DRG. NO.-CPC/CS/ 11/ 04 /2017/TYPE-ST/10

KANDY CASTING & ERRECTING

FENCE POST
DETAIL DRAWING
BSR ITEM-G-016 PLANNING (ENGINEERING SERVICES)
CASTING & ERRECTING FENCE POST
140
4R6
180
180
180
14BWG wire stirrups

at 150mm c/c
with grade 25 concrete
180
SECTION X-X
2250
180
180
180
180
180
X X
490
150
150
DRAWN BY- NISHANI SCALE-NTS DRG. NO.-CPC/CS/ 11/ 04 /2018/TYPE-ST/11
KANDY CASTING & ERRECTING

FENCE POST
DETAIL DRAWING
PERFARED PIPES BEHIND RETAINING WALL
working space
Water
proof with XYPEX
or equivalent
well compacted earth
Sander Chips
900 minimum
600
20mm Metal Pack
600
110mm dia.type 600 UPVC

perfarated pipe
(holes @ 150mm c/c staggered) TS 15 Geo textile membrane
& sloped
300
150
TOP VIEW OF PERFARATED PIPE
FOR CHECKED BY-
CENTRAL PROVINCE,
PERFARED PIPES IN
KANDY RETAINING WALL
DETAIL DRAWING

BSR ITEM - G-029 PLANNING (ENGINEERING SERVICES)
9" 4'-0" 9"
X 3" THICK CT.CON. COVER GRADE 20 MIX.
6" R/F WITH 10mm Ø TOR STEEL BARS AT 8" C/C

G.L. BOTHWAYS. THE COVER TO BE LAID IN TWO
SECTIONS WITH HANDLES.
9" THK.BRICK WORK IN CT. MOTAR

1:5 WITH 1/2" CT. RENDERING 1:3 .
6" FROM INLET UP TO COVER SLAB
6"
LEVEL .
9" THK. BRICK WORK IN CT. MORTAR

1:5 WITH EVERY ALTERNATIVE COURSE BELOW
6" FROM INLET TO BE LAID DRY WITH
1/4" VERTICAL SPACES BETWEEN BRICKS
10'-0"
2" 4" 3"
3"
6"
4"
GRADE 20 CT.
CONCRETE PAD
0'-9" 4'-0" 0'-9"

1'-2" 1'-2"
SECTION
R.C.C. CIRCULAR RING BEAM

R/F WITH 4 NOS. 12mm Ø TOR STEEL BARS
& 6mm Ø STIRRUPS AT 8" C/C. 9"
10"
12"
DETAIL AT X
ALTERNATIVE RING FOUNDATION
TO SINK PIT IN LOOSE SOIL
10 mm Ø TOR
LIFTING HANDLES
"
0-9
10mm Ø TOR STEEL

2" 4" 2"
0"
4'-
4"
"
0-9
SECTION THRO LIFTING HANDLE
PLAN
DEPARTMENT OF ENGINEERING SERVICES DRAWN BY- Nilmini SCALE -8 FEET TO AN INCH
DRG. NO.-CPC/CS/ 11/ 04 /2018/TYPE-SP/03 DATE - 16-11-2018

CENTRAL PROVINCE, BSR ITEM - H-014 CHECKED BY-
TYPE PLAN OF SOAKAGE PIT 4'-0"

(LOOSE SOIL) DEPUTY PROVINCIAL DIRECTOR (ENG.SERV.)
PROVINCIAL DIRECTOR (ENGINEERING SERVICES)
PLANNING
3" THICK CT.CON. COVER 1:2:4 (3/4" ) METAL
R/F OF 10mm Ø TOR STEEL
0'-9" 3'-0" 0'-9" BARS AT 8" C/C BOTHWAYS. THE COVER TO
X BE LAID IN TWO SECTIONS WITH HANDLES.
0'-6"
G.L.
9" THK.BRICK WORK IN CT. MOTAR 1:5 WITH

1/2" CT. RENDERING 1:3 .
0'-6"
2" 4" 3"
3"
6"
10'-0"
4"
GRADE 20 CT.
CONCRETE PAD
9"
2'-0"
SECTION DETAIL AT X
10mm Ø TOR STEEL

2" 4" 2"
9"
0'-
0"
4"
3'-
9"
0'-
SECTION THRO LIFTING HANDLE
PLAN


(HARD SOIL) DEPUTY PROVINCIAL DIRECTOR (ENG.SERV.)
PLANNING
6'-0" 4'' THICK CT.CON. COVER GRADE 20 MIX.
R/F WITH 10mm Ø TOR STEEL BARS AT 8" C/C
X BOTHWAYS. THE COVER TO BE LAID IN FOUR
G.L. SECTIONS WITH HANDLES.
0'-6"
6"
1:2:4 (3/4") CT. CON. PAD
12" GRADE 20
6" 9"X6" R.C.C. BEAM WITH GRADE 20 MIX.

R/F WITH 4 NOS. 12mm Ø TOR STEEL BARS
& 6mm Ø M.S STIRRUPS AT 6" C/C.
10'-0"
9" THK. BRICK WORK IN CT. MORTAR

1:5 WITH EVERY ALTERNATIVE COURSE BELOW
6" FROM INLET TO BE LAID DRY WITH
1/4" VERTICAL SPACES BETWEEN BRICKS
2" 4" 3"
12"
3"
6"
4"
SECTION
GRADE 20 CT.
CONCRETE PAD
10"
12"
9"
R.C.C. CIRCULAR RING BEAM
R/F WITH 4 NOS. 12mm Ø TOR STEEL BARS DETAIL AT X
& 6mm Ø STIRRUPS AT 8" C/C.
ALTERNATIVE RING FOUNDATION

TO SINK PIT IN LOOSE SOIL
10 mm Ø TOR
LIFTING HANDLES
" 10mm Ø TOR STEEL

0'-9
2" 4" 2"
0"
6'-
4"
"
0'-9 SECTION THRO LIFTING HANDLE
PLAN


(LOOSE SOIL) DEPUTY PROVINCIAL DIRECTOR (ENG.SERV.)
PLANNING
P.V.C. INLET PIPE 3" THICK CT. CON. GRADE 20 REINFORCED PRE-CAST .
B COVER SLABS REINFORCED WITH R6 @ 6" C/C * SEPTIC TANK TO BE FILLED WITH
3"
WATER UP TO "T.W.L. BEFORE BEING
X
G.L. PUT INTO USE.
G.L.
INTERNAL FACE OF SEPTIC TANK
TO BE RENDERED IN CEMENT
CT. CON. PAD
1'-2"
2"
GRADE 20 AS PER DETAIL . MORTAR IN TWO LAYERS
T.W.L. T.W.L. INTERNAL FACE OF SEPTIC TANK
TO BE RENDERED IN CEMENT MORTAR
1'-0"
EFFLUENT.
IN TWO LAYERS
6" dia. 1/2'' THK. EACH TWO COATS A WATER
6'-6"
PROOFING AGENT (THAROSEAL OR SMARTFLEX )
9" BRICK WORK
IN CT. MORTAR 1:5 . TO BE APPLIED ON THE FIRST LAYER
5'-0"
OF PLASTERING
3" 3/4" THICK

CT. PLASTERING 1:2.
* CHARACTERISTICS STRENGTH OF MATERIALS -
CONCRETE - 20 N /mm (fy)
(GRADE 20 CONCRETE TO BE USED)
6"
4"
3" 3"
3" THICK LEAN B 6" THICK BASE SLAB 9" 9"
3"
CONCRETE 1:3:6 ( 1" ) . 10mm Ø BARS L3

AT 9" CRS. BOTHWAYS. GRADE 20 NO SLOPE TO BE
PROVIDED.
SECTION A-A SECTION B-B
3" 3"
9" 2 NO. SLABS ABOVE INLET
3"
9" L1 9"
L2
AND OUTLET TO BE WITH
DIMENSIONS OF SEPTIC TANKS
2 NO. 10mm Ø M.S. LIFTING
9"
HANDLES AS PER DETAIL. L1 L2 L3

PERSONS L1+L2
ALL OTHERS WITHOUT
30 7'-0" 4'-6" 2'-6" 3'-0"
LIFTING HANDLES.
8'-0" 5'-0" -DO-
A A 40 3'-0"
L3
40 8'-0" 5'-0" 3'-0" -DO-
50 9'-0" 5'-6" 3'-6" -DO-

P.V.C. OUTLET PIPE.
60 10'-0" 6'-0" 4'-0" -DO-
9"
70 10'-0" 6'-6" 3'-6" 3'-6"
80 11'-0" 7'-0" 4'-0" -DO-

PLAN
3"
90 12'-0" 7'-6" 4'-6" -DO-
100 13'-0" 8'-6" 4'-6" -DO-
DRAWN BY- Nilmini SCALE -4 FEET TO AN INCH DRG. NO.-CPC/CS/ 11/ 04 /2018/TYPE-SEPT/01-(i)
DEPARTMENT OF ENGINEERING SERVICES TYPE PLAN OF SEPTIC TANK

CHECKED BY- DATE - 31-10-2018
CENTRAL PROVINCE, FOR 30-100 PERSON (BRICK)

BSR ITEM - H-019
DEPUTY DIRECTOR (STRUCTURAL DESIGNER) DIRECTOR (ENGINEERING SERVICES)
SECURITY WELD MESH DOOR WITH LOCKING DEVICE
40x5 flat iron
25mmx25mmx5mm
MS ANGLE IRON
40x40x5 Angle iron
50x50 swg 10
GI mesh
DETAIL at -A
40mm x 40mm x 5mm
MS Angle Iron frame
A 25mmx25mmx5mm
MS ANGLE IRON
GI sheet
LOCKING DEVICE
NOTE:
ALL CONNECTIONS TO BE WELDED
TYPE PLAN DRAWN BY- SHARLY SCALE-1:30 /1:100/1:250 DRG. NO.-CPC/CS/ 11/ 04 /2017/TYPE-ST/06
DEPARTMENT OF ENGINEERING SERVICES
FOR DESIGNED BY- Eng. A.G.SAMARASINGHE DATE - 01-11-2017
CENTRAL PROVINCE, SECURITY WELD CHECKED BY-
KANDY MESH DOOR

WITH LOCKING DEVICE
DETAIL DRAWING

BSR ITEM -J-029 PLANNING (ENGINEERING SERVICES)
SECURITY WELD MESH IN OPEN TYPE BUILDINGS
40 mmx 40 mmx 5 mm
Angle Iron Frame
T shape
30mmx5mm 30mmx5mm
flat iron flat iron 40mmx5mm
flat iron
30mmx5mm
flat iron
50mmx50mm
GI MESH 40mmx40mmx5mm
angle iron
30 flat iron
40 flat iron
DETAIL at -A NOTE:
TYPE PLAN DRAWN BY- SHARLY SCALE- NTS DRG. NO.-CPC/CS/ 11/ 04 /2017/TYPE-ST/07
DEPARTMENT OF ENGINEERING SERVICES FOR DESIGNED BY- Eng. A.G.SAMARASINGHE DATE - 01-11-2017
CENTRAL PROVINCE, SECURITY WELD CHECKED BY-
KANDY MESH IN OPEN TYPE

BUILDINGS
DETAIL DRAWING
PROVINCIAL DIRECTOR
BSR ITEM-J-030 DEPUTY PROVINCIAL DIRECTOR (Eng. Services)
PLANNING (ENGINEERING SERVICES)
SPECIAL SECURITY GRILL FIXED TO WINDOWS
1050mm
R 5.25mm
540mm
16x5 MS flat iron
1200mm
120mm
16x5 MS flat iron

135mm
105mm
NOTE:
DRAWN BY- SHARLY SCALE-NTS DRG. NO.-CPC/CS/ 11/ 04 /2018/TYPE-ST/09

TYPE PLAN
DEPARTMENT OF ENGINEERING SERVICES FOR DESIGNED BY- Eng. A.G.SAMARASINGHE DATE - 01-11-2018
CENTRAL PROVINCE, SPECIAL SECURITY CHECKED BY-
KANDY GRILL FIXED TO

WINDOWS
DETAIL DRAWING
(REVISED DESIGN-2018)
BSR ITEM - J-033 PLANNING (ENGINEERING SERVICES)
2 / 65x65x5mm "L" ANGLE
(TOP CHORD)
6"
mum
60 x 60x 5mm"L" ANGLE PURLIN maxi
2 / 65 x 65x 5mm "L" ANGLE 60 x 60x 5mm "L" ANGLE PURLIN

65 x 65x 5mm
7" "L" ANGLE
2 / 65 x 65x 5mm "L" ANGLE
4 2"
1
(TOP CHORD)
10mm THICK
M.S. GUZZLE PLATE WELDED
6"
6"
6mm THICK
12mm THICK BASE 50x50x5mm "L" angle
M.S. PLATE WELDED
PLATE WELDED
2 / 65x65x5"mm "L" ANGLE
"
5"
1'-3
(BOTTOM CHORD)
2" x 7 8" SLOTS FOR 3 4"Ø RAG BALT

2 / 65 x 65x 5mm "L" ANGLE 10mm THICK
(BOTTOM CHORD) M.S. GUZZLE PLATE WELDED
DETAIL AT "B"
DETAIL AT "A"
DETAIL OF WEB TRUSS -TYPE 1

ALUMINIUM PARTITION DRAWINGS
TYPE 01 (Ref Nl-ool ,N.06) wPE 02 {Ref sr oo2-!r.l:Qo6 )

F_-4'4u,++,{+4,{- F_4'-0'l--.|.--.-.4,,0"--.--F2,{'q
CLASS GT.ASS CLASS GLASS GLASS

o
"'
+
.ct-{ss CLASS GLASS PVC PLY PVC PLY
BOARD BOARD
+
PVC }LY PVC PLY PVC ?LY
BOARD BOARD BOARD
Jlllq (Ref N'oo3 , 'oo7 ) TYPE 04 ( nr.doq.- , N -.@o8 r)
l-.------{'{rt-_-.-l-.------.a'{'--2'a'-J F-316'--l-3'{'+3'6-
PVC PLY PVC PLY ?vc
BOARD BOARD PLY
BOAXD
GLASS GLASS
DOOR
OPENING
CLASS GI-ASS 3
PVC }LY PVC ?LY
BOARD BOARD
T
PVC PLY
BOARD
PVC PLY
BOARD
::<
4
ANNEX – 02
Approved Construction Material Price for
2021
CENTRAL PROVINCIAL PRICE COMMITTEE - 2021 FIRST HALF
D.C.S.(ENGINEERING) OFFICE
*All materials must be according to Sri Lanka standards. As for as possible
*All prices should be excluding VAT
2021
Item
Item. Unit. Approved
No
Rates
Labour:
Special skill labour (Aluminium Fabricator,
1 day 3,000.00
Tarman,Electrician,Plumber,Welder,Tiler…etc)
2 Skill labour day 2,500.00
3 Semi skill labour day 2,000.00
4 Unskill labour day 1,800.00
5 Scavenging Labour ( Cleaning) Day 2,000.00
6 Specialized Sanitory Labour Day 3,500.00
7 Plumber day 3,000.00
8 Tinker day 2,500.00
9 Welder day 3,000.00
10 Electrician day 3,000.00
11 Painter day 2,500.00
12 Bllow boy ( unskilled) day 1,800.00
13 Concreate mixer Operator day 2,000.00
14 Poker Operator day 2,000.00
Rubble / Metal / Quarry dust: (Including loading &

unloading cost. )
15 Quarry dust. m3 1,590.00
16 Chips. ( 12.5 mm Down graded ) m3 2,055.00
17 Coarse aggregate 3/4" (20mm) m3 3,180.21
18 Coarse aggregate 1"(25mm) m3 2,473.50
19 Coarse aggregate 1 1/2"(37.5mm) m3 2,296.82
20 Crusher Production (12.5mm)aggregate m3 2,250.00
21 Coarse aggregate 4"(100mm) m3 1,520.00
22 Rubble (6" x 9") (150mmx225mm) m3 1,360.00
23 Chips. ( 6.3 mm Down graded ) m3 1,759.50
24 Crusher Production (19 mm) Aggregate m3 2,800.00
25 (150mm -225mm) rubble including piling Cu.m 1,219.00
26 Manually Production (100mm) Aggregate Cu.m 1,640.00
Provincial Price Committee 2021 page1

2021
Item
No
Rates
29 Manually Production (37.5mm) Aggregate Cu.m 2,750.00
31 Cu.m 2,350.00
Crusher Produced (37.5mm)graded (table 1701.5 for ABC)
32 Aggregate for seal coat 19mm (SSCM table 1701-8) Cu.m 2,800.00
33 Cu.m 3,500.00
Aggregate for seal coat 12.5mm (SSCM table 1701-8)
34 Cu.m 3,401.00
Aggregate for seal coat 9.5 mm (SSCM table 1701-8)
35 Approved soil type I & II for bases & shoulders Cu.m 415.00
36 Approved soil type I & II for embankments m3 409.00

37 Crusher Production (37.5mm)-do- (S.S.C.M.T:1701-4) Cu.m 2,350.00
38 Crusher Production (50mm)-do- (S.S.C.M.T:1701-4) Cu.m 1,759.00
39 Crusher Production (25mm)aggregate Cu.m 2,296.00
40 Crusher fines (6.3 mm down wards ) m3 1,802.00
Sand:
41 River sand m3 3,533.00
42 River sand for road surface (SSCM table 1701-9) Cu.m 3,885.00
43 Offshore sand ( Wash & Siebed) m3 3,427.00
44 Gravel m3 580.00
45 Soil m3 420.00
Bricks:
Bricks - Size (8 3/4'' x 4 1/2'' x 2 3/4'' Nominal )
46 1000 nrs 16,000.00
(225mmx112.5mmx70mm)
Bricks - ( Large Size Volume 1.5 larger than Engineering
47 1000 nrs 22,000.00
Bricks Nominal)
Cement /Lime
48 Cement 50 Kg 925.92
49 Cement (Colour) 1kg 740.74
50 Slacked Lime Powder 20 Kg 300.00
51 Lime Paste (Powder - boiled) 20 Kg 350.00
Bitumen and related materials

52 Bitumen 80-100 ( 200 Liters drums ) (ex-stockist) ltr 69.00
53 Bitumen 60-70 (140 Liters drums) (Ex Stock) ltr 53.50
54 Emulsion C.S.S.01 (Excluding Transp.) ltr 66.00

2021
Item
No
Rates
55 Emulsion C.R.S.01(Excluding Transp.) ltr 62.00
56 Emulsion C.R.S.02(Excluding Transp.) ltr 66.00
57 Asphalt concrete Wearing surface 60 - 70 19mm MT 8,700.00

58 Asphalt Bound Base MT 8,200.00
Asphalt concrete Surfacing materials binder 60/70 5% mix -
59 MT 8,625.00
dense (19mm) Ex-plant
Asphalt concrete Surfacing materials binder 60/70 5% mix -
60 MT 8,500.00
dense (19mm)
Asphalt concrete bound base material binder 3.53% mix -
61 MT 9,000.00
dense (37.5mm) - ex plant
Asphalt concrete -cold mix with cut back 20% binder 5.5%
62 MT 10,000.00
MIX*- dense (19mm) Ex-plant
Cold mixed asphalt with emultion CSS-1 (6.67% by wgt of 10,000.00
63 MT
agg.) & 19mm Aggregate Ex-plant
64 Bitumen80/100 [bulk] (ex refinery) for asphalt plant kg 68.00
Bitumen 60/70 (Bulk) (Delivery at Site) for all asphalt
65 kg 68.00
plants
66 Handling Bitumen supplied by Authority lt 1.00
Concrete / Cement Products

Interlocking Paving Block 220mm x110mmx80mm gray
67 nr 35.00
colour Grade 15
Interlocking Paving Block 220 mmx110mmx80mm colour
68 nr 40.00
Grade 15
69 nr 47.00
Grade 25
Interlocking Paving Block 220 mmx110mmx80mm gray
70 nr 42.00
colour Grade 25
Interlocking Paving Block 220mm x110mmx80mm gray
71 nr 45.00
colour Grade 30
72 nr 50.00
Grade 30
Cement sand blocks 1:10, (400mmx200mm100mm)
73 nr 52.78
(hollow)
Cement sand blocks (hollow) 1:10, 16"x8"x6"
74 nr 67.59
(400mmx200mm150mm)
Cement sand blocks (hollow) 1:10, 16"x8"x8"
75 nr 99.07
(400mmx200mmx200mm)
Cement block (solid) 12" X 4" X 7"
76 nr 64.81
(300mmx100mmx175mm) 2 N/mm2
77 nr 92.59
78 nr 96.30

2021
Item
No
Rates
Reinforce concrete Pipe dia.(153mm)lenth(2438 mm)
79 No 4,300.00
(Nominal)
Reinforce concrete Collar dia.(153mm)lenth(2438 mm)
80 No 450.00
(Nominal)
81 No 5,300.00
(Nominal)
82 No 550.00
(Nominal)
83 No 7,000.00
(Nominal)
84 No 650.00
(Nominal)
85 No 8,775.00
(Nominal)
86 No 750.00
(Nominal)
87 No 10,750.00
(Nominal)
88 No 850.00
(Nominal)
89 No 24,500.00
(Nominal)
90 No 1,400.00
(Nominal)
91 No 41,000.00
(Nominal)
92 No 1,600.00
(Nominal)
Standard road kerb 125x250x900 G20 concrete (Ex factory)
93 No 1,200.00
(Nominal)
94 Paving slab 450x450x50mm G20 concrete (Nominal) No 650.00
95 Bridge kerb 915 (Nominal) No 950.00

Standard reinforced concrete uprights for bridges (new
96 No 2,400.00
design) Drawing No. T/B/102/B
Standard reinforced concrete Hand rails for bridges (new
97 No 2,100.00
design) Drawing No.T/B/102/B
98 Coupling pairs for hand rails pair. 900.00
300mm dia. Semi circular Rain water channels 609 mm long
99 No 250.00
(Nominal)
Ready mixed concrete

100 Ready mixed concrete (grade 15) Transport upto 15km m3 14,400.00
101 Ready mixed concrete (grade 20) Transport upto 15km m3 14,700.00
102 Ready mixed concrete (grade 25)Transport upto 15km m3 15,200.00

2021
Item
No
Rates
103 Ready mixed concrete (grade 30)Transport upto 15km m3 15,600.00
104 Ready mixed Concrete Transport beyond 15km m3 60.00

Minimum charge for pumping Car ( Up to 30 m3) Transport
105 Item 21,500.00
upto 15km
106 m3 750.00
Additional charge for pumping concrete (1m3)upto 15km
Additional Transport charge for pumping Car beyond
107 km 200.00
15km(per km)
Asbestos Items:
108 Asbestos roofing sheets (corragated) m2 730.56
109 Asbestos ridging close fit. (1100mm)long pair nr 782.41
110 Asbestos ceiling sheets. (1200mmx1200mm) nr 560.87
Zn/Al Products
111 Zn/Al Roofing sheet (0.47mm thick) (Trim Clad) m2 1,292.00
Zn/Al Roofing sheet (0.47mm thick) (Tile
112 m2 1,350.00
Profile)
113 Zn/Al Ridge cap,(0.47mm thick) m 554.00
114 Zn / Al Down pipe 100mm X 100mm, 0.47mm thick m 541.00
115 nr 289.80
Zn / Al Down pipe bend 100 mmX 100 mm, 0.47mm thick
116 nr 1,549.00
Zn / Al Down pipe offset 100mm X 100 mm, 0.47mm thick
117 Zn / Al Down pipe Bracket nr 19.00
118 Zn / Al Nozzle nr 300.00
119 Zn / Al Gutter (470 mm Girth ) m 575.00
120 Zn / Al End Cap 0.47mm thick nr 136.00
121 Zn / Al Guter Bend 0.47mm thick nr 545.00
122 Zn / Al Guter Box 0.47mm thick nr 670.00
123 Zn / Al Guter bracket 0.47mm thick nr 52.00
124 Zn / Al Egde/Gable capping 0.47mm thick m 448.00
125 m 313.00
Zn / Al Corner capping for wall cladding 0.47mm thick
126 Zn / Al 0.47mm thick barge cap m 554.00
127 Zn / Al End capping 0.47mm thick m 313.00
128 Zn / Al Corner capping 0.47mm thick m 448.00
129 Zn / Al Bottom capping 0.47mm thick m 448.00
130 Zn / Al Top capping 0.47mm thick m 554.00

2021
Item
No
Rates
131 Zn / Al Shoe 0.47mm thick nr 474.00
132 Zn / Al Apron Flashing 0.47mm thick m 580.00
133 Zn / Al Vally Gutter 0.47mm thick m 554.00
134 Self Drilling Screws 2 1/2" (67.5mm)(Fasteners) nr 17.50
135 Self Drilling Screws 2" (50mm) (Fasteners) nr 14.50
136 Self Drilling Screws 12-14 mm ×55mm nr 14.50
137 m 943.00
Lipped Channel Size 100mm x 50mm x 12mm (2mm tk.) GI
138 m 1,294.00
Lipped Channel Size 150mm x 65mm x 14mm (2mm tk.) GI
139 C -Purlin 100mm x 50mm (2mm tk.) m 690.00
140 75mm x75mm gauge 17 welded wire mesh m2 109.63
Laminated aluminium foil, 4mm thick double side double
141 m2 420.00
bubble insulation layer
Zn/Al Sandwich pannel Roofing- 30mm (Sheet thickness -
142 m2 4,800.00
Top 0.47mm, Bottom -0.35mm)
Zn/Al Sandwich pannel Roofing - 40mm (Sheet thickness -
143 m2 5,450.00
144 m2 5,850.00
145 m2 6,300.00
Ceiling
146 PVC Ceiling pannels width 200mm m2 1,291.67
147 PVC Ceiling pannels 600mm x 600mm m2 638.89
148 PVC Ceiling pannels (Laminated) 600mmx 600mm m2 597.22
149 PVC Molding & beading m 98.43

150 600mm x 600mm ceiling accessary Main runner m 69.72
151 600mm x 600mm ceiling accessary wall angle m 47.57
152 600mm x 600mm ceiling accessary cross Tee 600mm nr 55.00
Gabian Boxes & Fencing Materials

Galvanized Wire Gabion Box 1.5m x 1.0m x 1.0m (mesh
153 nr 4,750.00
opening 80mmx100mm)
P.V.C. Coated Wire Gabion Box 1.5m x 1.0m x 1.0m (mesh
154 nr 5,800.00
opening 80mmx100mm)
Galvanized Wire Gabion Box2.0m x 1.0m x 1.0m(mesh
155 nr 6,100.00
opening 80mmx100mm)

2021
Item
No
Rates
P.V.C. Coated Wire Gabion Box2.0m x 1.0m x 1.0m(mesh
156 nr 7,800.00
opening 80mmx100mm)
Galvanized Wire Gabion Box1.0m x 1.0m x 1.0m(mesh
157 nr 3,600.00
opening 80mmx100mm)
P.V.C. Coated Wire Gabion Box1.0m x 1.0m x 1.0m(mesh
158 nr 4,300.00
opening 80mmx100mm)
159 Gabion additional lacing wire kg 330.00
160 Geotextile TS30 1.5mm tk m2 180.00
161 PVC Coated Gabion additional lacing wire kg 450.00
Barbed Wire gauge14 , 4 point 100mm apart (Approx.
162 m 24.20
285m) 25kg .
Chain Link Mesh P.V.C.Coated GI wire (12BWG)
163 nr 7,052.78
50mm×50mm,1.0m high (15m roll)
164 nr 10,578.70
165 nr 14,104.63
G.I Pipe and Box Bar

166 2.0mm thick 40mm x 40mm GI Box Bar m 392.25
167 2.0mm thick 50mm x 50mm GI Box Bar m 518.55
1.8mm thick,1/2" thread size (21.2mm avg.outside dia.)GI
168 m 197.96
Pipe
169 m 253.03
Pipe
2.0mm thick,1" thread size (33.5mm avg.outside dia.)GI
170 m 349.62
Pipe
171 m 515.64
Pipe
172 m 589.08
Pipe
173 m 775.86
Pipe
174 m 1,422.00
Pipe
175 m 775.06
Pipe
176 m 1,995.00
Pipe
177 m 1,060.82
Pipe
178 m 1,374.52
Pipe
179 Base cup for G I pipe 50mm outer dia nr 45.00
180 Base cup for G I pipe 40mm outer dia nr 40.00
181 Base cup for 50mm× 50mm GI box bar nr 110.00
182 Base cup for 40mm× 40mm GI box bar nr 80.00

2021
Item
No
Rates
Timber : - Timber corporation rates. (Included
loading & unloading cost. )
Timber 4"x3"(100mmx75mm) Special (Nominal size )Teak
183 m 1,725.50
-below 3m
Timber 4"x2"(100mmx50mm)Special(Nominal size ) Teak -
184 m 1,150.33
below 3m
185 m 696.21
Timber 4"x2" cl.I (Nominal size ) Micro 4.2m<×<5.4m
Timber 4"x2"(100mmx50mm) cl.II (Nominal size )
186 m 451.86
bellow4m
187 Timber 4"x2"(100mmx50mm)cl.III (Nominal size) m 155.12
188 Timber 2"x2" (50mmx50mm) cl.I (Nominal size ) Micro m 242.42

below 4m
Timber 2"x2"(50mmx50mm) cl.II (Nominal size ) below
189 m 145.13
4m
Timber 2"x2"(50mmx50mm) cl.III (Nominal size ) below
190 m 88.18
4m
Timber 2"x1" (50mmx25mm) cl.I (Nominal size ) Micro,
191 m 76.06
below 4m
Timber 2"x1" (50mmx25mm)cl.II (Nominal size ) below
192 m 72.56
4m
Timber 2"x1" (50mmx25mm) cl.III (Nominal size ) below
193 m 28.24
4m
194 Coconut rafters 4"x2"(100mmx50mm)(Nominal size ) m 80.00
195 Ginisapu 4"x2" (Nominal size ) m 466.67
Timber planks 1 1/4" (32mm) thick Special (Nominal size)
196 m2 10,350.45
Teak below 3m , 225mm wide
Timber planks 1 1/4" (32mm) thick cl.I (Nominal size)
197 m2 4,068.15
Mahogani below 5.6m , 225mm wide
Timber planks 1 1/8" (28mm) thick Special (Nominal size )
198 m2 9,348.77
Teak below 3m,225mm wide
Timber planks 1 1/8"(28mm) thick cl.I(Nominal size )
199 m2 3,660.91
Mahogani below 5.6m,225mm wide
Timber planks 1"thick Special(Nominal size) Teak below
200 m2 8,347.13
3m
Timber planks 1" (25mm) thick cl.I (Nominal size )
201 m2 3,268.48
Mahogani below 5.6m,225mm wide
Timber planks 1" (25mm) thick cl.II (Nominal size ) below
202 m2 1,479.06
5.6m,225mm wide - Cypress
Timber planks 1"(25mm)thick cl.III(Nominal size ) below
203 m2 591.23
5.6m,225mm wide - Cypress
204 m2 3,041.97
Timber planks 3/4"(20mm)to 1"(25mm)cl.I (Nominal size )
205 m2 2,522.59
Timber planks 3/4" (20mm)to 1" (25mm)cl.II(Nominal size )
Timber planks 3/4" (20mm) tongued & grooved -
206 m2 968.00
''Lunumiddalla''. (Nominal size )

2021
Item
No
Rates
Kempas Timber , (Approved Hard Wood) 4"x3"
207 m 1,148.00
(100mmx75mm) (Nominal size )
208 m 721.00
209 m 262.00
210 m 131.00
211 nr 265.00
JungleTimber props 3" (75mm) dia., 2.5m to 3.5m length
212 m 3,270.70
Kumbuk timber 6'' X 3'' (150mmx75mm) (Nominal size )
213 Beading 1 1/2"X 1/2" (37.5mmx12.5mm) m 32.80
214 Moulding 1 1/2"X 1 1/2" (37.5mmx37.5mm) (Midella) m 45.92
215 Beading 1/2" x 1/2" (12.5mmx12.5mm) m 9.00
216 Round Timber 3" (75mm) dia.upto 2.5m m 45.00
Timber round jungle-100mm minimum & 150 mm average
217 m 80.00
diameter (incl transport)
Timber round jungle-150mm minimum & 200 mm average
218 m 150.00
diameter (incl transport)
219 Firewood m3 1,400.00
220 Bamboo tree length greater than 8 meters nr 483.00
221 m 472.32
Ginisapu plank 9" x 3/4" (225mmx20mm) (Nominal size )
Jack timber 4" x 3"(100mmx75mm) (Nominal size ) ,below
222 m 1,452.45
5.6m,225mm wide
Jack timber 4" x 2" (100mmx75mm) (Nominal size ) ,below
223 m 952.48
5.6m,225mm wide
224 Mee timber 6'' X 3'' (150mmx75mm) (Nominal size ) m 961.25
225 Fillet 1/2''× 1/2'' (12.5mm× 12.5mm) (Nominal Size) m 7.00
226 Timber planks 1" thick & 8'' width classII m2 1,250.00
227 Timber planks 1" thick & 8'' width class III m2 875.00
228 2''×2'' Reepers class II m 220.00
229 2''×2'' Reepers class III m 100.00
230 Milla timber 6'' X 3'' (150mmx75mm) (Nominal size) m2 2,831.20

Cu.dm
231 91.50
Sawn timber class 1 (local)-(incl Loading ,unloading) (dm)3
Cu.dm
232 54.50
Sawn timber class 2 (local)-(incl Loading ,unloading) (dm)3
233 Wooden Plug 2'' X 1'',8" Long Class I nr 81.54
234 825mm×2025mm×31mm Plywood door sash nr 3,000.00

2021
Item
No
Rates
Plywood board (normal)

235 Plywood board -18 mm m2 1,090.10
236 Plywood board -15 mm m2 934.38
238 Plywood board-9 mm m2 716.35
240 Plywood board-3 mm m2 264.74
Ply wood -Laminated board (Double side)

241 Laminated Plywood board 18 mm m2 1,560.00
Steel :
244 QT steel bars MT 150,000.00
245 Mild Steel MT 150,000.00
246 Angle Steel MT 134,259.26
247 Flat Iron MT 134,259.26
248 M.S.Plate 12mm thick MT 132,173.91
249 "I" Section MT 162,037.04
250 MS Chanel MT 148,148.15
251 Box Bar MT 173,611.11
252 H Section MT 162,037.04
253 Tor Steel Kg 150.00
254 steel Sheet (8'×4') 6mm thick nr 20,833.33
255 steel Sheet (8'×4')10mm thick nr 37,037.04
256 Stainless steel 20mm dia m 2,990.00
Paint :
257 Enamel Paint (4ltr) nr 4,166.67

2021
Item
No
Rates
258 Emulsion Paint (4ltr) nr 3,694.44
259 Exterier emulsionPaint (4ltr) nr 4,675.93
260 Primer (wall) Paint (4ltr) nr 1,138.89
261 Anticorrosive Paint (4ltr) nr 2,962.96
262 Skim coat 20kg nr 680.00
263 Wall putty (7kg) nr 1,291.67
264 Thinner (4ltr) nr 1,060.19
265 Roofing Paint (4ltr) nr 4,583.33
266 Floor paint (4ltr) nr 3,824.07
267 Wax & Polish (1 kg) nr 1,638.89
268 Varnish polythurethane (4ltr) nr 4,055.56
269 Wood Preservatives (stain) (4ltr) nr 1,092.59
270 Wood Preservatives (clear) (4ltr) nr 1,546.30
271 Wood primer Paint (4ltr) nr 3,500.00
272 Paint metal Primer Zinc Phosphate (4ltr) nr 4,907.41
273 Sealer (4ltr) nr 4,805.56
274 Brush 2" (50mm) nr 361.11
275 Brush 3" (75mm) nr 444.44
276 Brush 6" (150mm) nr 740.74
277 Roller Brush 9" nr 833.33
278 Wire Brush nr 324.07
279 Sand Paper nr 55.56
280 Coir brush 6" (150mm) nr 150.00
281 Thermoplastic road marking material (white) kg 165.00
282 Thermoplastic road marking material (yellow) kg 165.00
283 Paint-reflective ltr 1,430.00
284 Rust remover ltr 2,750.00
285 Road marking paints (yellow) ltr 883.15
286 Road marking paints (white) ltr 692.39
PVC
287 Bend P V C 1/2" (20mm) nr 31.48

2021
Item
No
Rates
288 Bend P V C 3/4" (25mm) nr 45.37
289 Bend P V C 1" (32mm) nr 62.04
290 Bend P V C 1 1/4" (40mm ) nr 136.11
291 Bend P V C 1 1/2" (50mm) nr 212.96
292 Bend P V C 2" (63mm ) nr 345.37
293 Bend P V C 2 1/2" (75mm ) nr 717.59
294 Bend P V C 3" (90mm ) nr 1,546.30
295 Bend P V C 4" (110mm ) nr 2,314.81
296 Bend P V C 6" (160mm ) nr 4,493.73
297 Elbow P.V.C. 1/2" nr 18.52
298 Elbow P.V.C. 3/4" nr 37.04
299 Elbow P.V.C. 1" nr 46.30
300 Elbow P.V.C. 1 1/4" nr 87.96
301 Elbow P.V.C. 1 1/2" nr 134.26
302 Elbow P.V.C. 2" nr 185.19
303 Elbow P.V.C. 4" nr 824.07
304 Socket P.V.C 1/2" nr 18.52
305 Socket P.V.C 3/4" nr 29.63
306 Socket P.V.C 1" nr 43.52
307 Socket P.V.C 1 1/2" nr 97.22
308 Socket P.V.C 1 1/4" nr 63.89
309 Socket P.V.C 2" nr 126.85
310 Tee P.V.C 1/2" nr 23.15
311 Tee P.V.C 3/4" nr 46.30
312 Tee P.V.C 1" nr 69.44
313 Tee P.V.C 1 1/4" nr 114.81
314 Tee P.V.C 1 1/2" nr 194.44
315 Tee P.V.C 2" nr 252.78
316 Tee P.V.C 4" Sewer nr 1,092.59
317 Drainage Tee P.V.C with Eye 4" nr 800.93
318 Drainage Y Junction, P.V.C 4" nr 754.63
319 Drainage Y Junction with Eye- P.V.C 4" nr 958.33
320 Pipe P.V.C 1/2" (PNT 14) m 52.08
321 Pipe P.V.C 3/4" (PNT 11) m 135.42
322 Pipe P.V.C 1" (PNT 11) m 251.16
323 Pipe P.V.C 1 1/4" (PNT 11) m 344.91

2021
Item
No
Rates
324 Pipe P.V.C 1 1/2" (PNT 11) m 475.69
325 Pipe P.V.C 2" (PNT 11) m 812.50
326 Pipe P.V.C 2 1/2" (PNT 11) m 1,427.08
327 Pipe P.V.C 3" (PNT 11) m 2,430.56
328 Pipe P.V.C 4" (PNT 11) m 3,111.11
329 Pipe P.V.C 1" (PNT 9) m 217.59
330 Pipe P.V.C 1 1/4" (PNT 9) m 282.41
331 Pipe P.V.C 1 1/2" (PNT 9) m 395.83
332 Pipe P.V.C 2" (PNT 9) m 666.67
333 Pipe P.V.C 2 1/2" (PNT 9) m 1,240.74
334 Pipe P.V.C 3" (PNT 9) m 2,111.11
335 Pipe P.V.C 4" (PNT 9) m 2,513.89
336 Pipe P.V.C 1" (PNT 7) m 87.96
337 Pipe P.V.C 1 1/4" (PNT 7) m 247.69
338 Pipe P.V.C 1 1/2" (PNT 7) m 280.09
339 Pipe P.V.C 2" (PNT 7) m 509.26
340 Pipe P.V.C 2 1/2" (PNT 7) m 993.06
341 Pipe P.V.C 3" (PNT 7) m 1,027.78
342 Pipe P.V.C 4" (PNT 7) m 1,449.07
343 Pipe P.V.C 6" (PNT 7) m 2,634.26
344 Pipe P.V.C 6" (PNT 7) SS m 2,717.59
345 Pipe P.V.C 1 1/2" (Class 4) Non Pressure m 208.33
346 Pipe P.V.C 2" (Class 4) Non Pressure m 418.98
347 Pipe P.V.C 4" (Class 4) Non Pressure m 680.56
348 Pipe P.V.C 4" Drainage pipe m 833.33
349 Pipe P.V.C 6" Drainage pipe m 1,069.44
350 Pipe P.V.C 4" Non Pressure (Drainage SS) m 694.44
351 Pipe P.V.C 6" Non Pressure (Drainage SS) m 2,138.88
352 P.V.C Gully 6" cover nr 250.00
353 P.V.C Brackets 4" dia (Sandle Clip) nr 129.63
354 P.V.C Brackets 2" dia (Sadle Clip) nr 19.44
355 P.V.C Brackets 1 1/2" dia (Sadle Clip) nr 18.52
356 P.V.C Brackets 1 1/4" dia (Sadle Clip) nr 17.59
357 P.V.C Brackets 1" dia (Sadle Clip) nr 15.74
358 P.V.C Brackets 3/4" dia (Sadle Clip) nr 13.89
359 P.V.C Brackets 1/2" dia (Sadle Clip) nr 10.19

2021
Item
No
Rates
360 P.V.C Down Pipe 3 1/2",12' Pipe length nr 634.26
361 P.V.C Gutter 6" Rectanguler type,12' Long length nr 828.70
362 Gutter Joint nr 125.00
363 Mitre Joint nr 407.41
364 Gutter End Cap nr 115.74
365 Gutter Box nr 754.63
366 P.V.C downpipe clip nr 29.63
367 Runing Head nr 282.41
368 P.V.C Elbow - 3 1/2" nr 183.33
369 P.V.C Joiner -3 1/2" nr 148.15
370 Gutter Bracket- A nr 67.59
371 Gutter Bracket- B nr 29.63
372 Valve,Socket, 1/2" dia. (20mm) nr 25.00
373 Valve,Socket, 3/4"(25mm) nr 36.11
374 Valve,Socket, 1"(32mm) nr 46.30
375 Valve,Socket, 1 1/4"(40mm) nr 77.78
376 Valve,Socket, 1 1/2"(50mm) nr 101.85
377 Valve,Socket, 2"(63mm) nr 141.67
378 Plastic Stop Cock 3/4" dia. (25mm) nr 185.19
379 Plastic Stop Cock 1/2" dia. (20mm) nr 148.15
380 Plastic Stop Cock 1" dia. (32mm) nr 314.81
381 Brass Ball Cock 1 1/4" dia. (40mm) nr 391.30
382 Tread seal tape (roll) nr 23.15
383 Faucet Socket 1 1/4" dia. nr 83.33
384 Faucet Socket 1/2" dia. nr 23.15
385 Faucet Socket 3/4" dia. nr 37.04
386 Faucet Socket 1" dia. nr 46.30
387 Faucet Socket 1 1/2" dia. nr 111.11
388 Faucet Socket 2" dia. nr 150.93
389 Faucet Elbow 1/2" dia. nr 44.44
390 Faucet Tee 1/2" dia. nr 58.33
391 Faucet Socket 1/2" dia. Brass Inserted nr 64.81
392 Faucet Elbow 1/2" dia. Brass Inserted nr 83.33
393 Faucet Tee 1/2" dia. Brass Inserted nr 125.00
394 P.V.C Sewer Bend 110mm dia. nr 402.78
395 P.V.C Sewer Bend 110mm dia. with inspection Eye nr 671.30

2021
Item
No
Rates
396 Reducing Socket 20 x 25 mm nr 29.63
411 Reducing Tee 20 x 25 mm nr 44.44
426 End Cap P.V.C 1/2" nr 25.93
427 End Cap P.V.C 3/4" nr 33.33
428 End Cap P.V.C 1" nr 43.52
429 End Cap P.V.C 1 1/4" nr 63.89
430 End Cap P.V.C 1 1/2" nr 87.96
431 End cap P.V.C. 2" nr 115.74

2021
Item
No
Rates
432 End Cap P.V.C 2 1/2" nr 240.74
433 End Cap P.V.C 3" nr 439.81
434 End Cap P.V.C 4" nr 490.74
435 P.V.C.Pipe 110 mm dia type 250 m 370.00
436 PV.C.Pipe 110 mm dia type 400 m 192.50
437 PV.C.Pipe 110 mm dia type 400 m 610.00
438 Bend cowl P.V.C. 110mm nr 198.26
439 Solvent Cement kg 2,611.11
440 Polymer Water Tank 500 lit nr 4,262.50
441 Polymer Water Tank1000 lit nr 9,179.44
Sanitury Fittings
444 Cromium plated Piller tap nr 3,750.00
445 nr 3,796.30
Cromium plated Piller tap ( Rocell Vero or equivalent )
446 nr 2,129.63
Cromium plated Bib tap ( Rocell SD9A126 or equivalent )
447 Chromium Plated Sawn neck Type Piller Tap nr 3,055.56
Chromium Plated Sawn neck Type Piller Tap (Rocell
448 nr 2,685.19
N091214 or equivalent)
449 Cromium plated Conseal Valve nr 2,731.48
Cromium plated Conseal Valve ( Rocell 4,074.07
450 nr
RB.TAB.OFA320.CB.PN or equivalent )
451 Urinal flush valve (Chromium Plated) nr 4,861.11
452 Urinal flush valve (Chromium Plated) -Rocell nr 6,851.85
453 Ceramic Closet Squatting - Medium nr 5,833.33
454 Rubber ring for sink nr 138.89
455 Plastic Low Level cistern nr 4,629.63
456 Ceramic Corner Wash Basin- nr 2,638.89
Ceramic Corner Wash Basin- (Rocell - Aqua
457 nr 8,518.52
RB.ACO.01G101.01.06 or equivalent)
458 Ceramic Wash basin 600x375x175 mm nr 7,870.37
Wash basin with pedestal Vitreous China 575 X 450 X
459 820mm ( Rocell urban D or equivalent) nr 13,148.15
460 Ceramic Laboratory Sink nr 6,481.48

2021
Item
No
Rates
Ceramic Laboratory Sink (Rocell - Xenon
461 nr 21,203.70
RB.XEN.08G102.01.09 or equivalent)
462 Sink Stainless Steel Single drain board nr 3,472.22
Sink Stainless Steel Single drain board ( Rocell ADRIAN
463 611 TRENDY 915 X 480mm or equivalent) nr 15,925.93
464 Chromium plated Shower rose, 150mm dia. nr 2,407.41

Chromium plated Shower rose (Rocell FHS 30A or
465 nr 6,574.07
Equivalent)
466 Bathroom Mirror 450 x 600mm nr 1,944.44
467 Chromium plated Flexible Hose 1 1/2ft. long 1/2" dia nr 509.26
468 Chromium plated Bidet Spray nr 2,962.96
469 Chromium plated Bidet Spray (Rocel SCL 01) nr 4,166.67
470 Plastic Water Tec Bidet Spray nr 921.30
471 Urinal bowls Small nr 3,500.00
472 Urinal bowls Small (Rocell FLO or equivalent) nr 25,277.78
473 Shower rose 1/2" dia. nr 750.00
474 Waste Plug nr 850.00
475 Waste Plug (Rocell A38, A43 or equivalent) nr 1,944.44
476 Rubber washer nr 37.04
477 Plastic Gully - 6"X6" nr 370.37
478 Plastic Gully - S lon nr 597.22
479 Plastic Tile Beading (Large) m 120.25
480 Plastic Tile Beading (Small) m 101.11
481 Al Tile Beading (Large) m 170.83
482 Al Tile Beading (Small) m 132.87
483 Tile Grout kg 222.22
484 Brass Ball cock 1/2" nr 1,064.81
485 Brass Gate Valve 1/2" - S lon (Vito) nr 1,092.59
486 Brass Gate Valve 3/4" - S lon (Vito) nr 1,240.74
487 Brass Gate Valve 1" - S lon (Vito) nr 1,527.78
488 Brass GateValve 1 1/4" nr 3,750.00
489 Brass GateValve 1 1/2" nr 5,450.00
490 Brass Gate Valve 1 1/2" - S lon (Vito) nr 2,601.85
491 Brass GateValve 2" nr 8,090.28

2021
Item
No
Rates
492 Brass Gate Valve 2" - S lon (Vito) nr 4,268.52
493 Brass Ball Valve 1/2" nr 1,995.00
494 Brass Ball Valve 1/2"- S lon (Vito) nr 837.96
495 Brass Ball Valve 3/4" nr 4,756.48
496 Brass Ball Valve 3/4"- S lon (Vito) nr 1,166.67
497 Brass Ball Valve 1" nr 8,500.00
498 Brass Ball Valve 1"- S lon (Vito) nr 1,907.41
499 Brass Ball Valve 1 1/4" - S lon (Vito) nr 3,393.52
500 Brass Ball Valve 1 1/2"- S lon (Vito) nr 4,722.22
501 Brass Ball Valve 2"- S lon (Vito) nr 7,268.52
502 Chromium plated Angle Valve 1/2" (Rocel A279 or nr 1,296.30

equvelant)
Chromium Plated Heavy Quality Piller Tap 1/2" dia. (semi
503 nr 5,324.07
Luxary)
Chromium Plated Heavy Quality Piller Tap 1/2" dia. (Rocell
504 nr 7,592.59
SD90943 or equivalent)
505 Plastic Bip Tap1/2" Quarter Turn Straight Handle nr 240.74
506 Plastic Bip Tap1/2" Round Handle nr 305.56
507 Plastic Basin Piller 1/2" Quarter Turn Straight Handle nr 717.59
Plastic Sink Piller Tap 1/2" Quarter Turn Straight Handle nr
508 717.59
Plastic Garden Tap 1/2" Quarter Turn Straight Handle nr
509 398.15
Plastic Bidet Shower nr
510 921.30
Plastic Stop Tap 1. 1/2" Round Handle nr
511 361.11
" " " 2. 3/4" Round Handle nr
512 537.04
" " " 3. 1" Round Handle nr
513 703.70
Plastic Stop Tap 1. 1/2" Tee Handle nr
514 263.89
" " " 2. 3/4" Tee Handle nr
515 402.78
516 " " " 3. 1" Tee Handle nr 555.56

Plastic Angle Valve 1/2" Quarter Turn Straight Handle nr
517 337.96
Plastic Flexible Hose 12" length nr 199.07

518
519 Plastic Flexible Hose 18" length nr 273.15

2021
Item
No
Rates
520 Plastic Flexible Hose 24" length nr 342.59
Aluminum
Anodized Aluminium architectural section No 100D 3105 or
521 m 1,687.18
similar sections.
Anodized Aluminium architectural section No SPR 106 or
522 m 774.74
similar sections.
Anodized Aluminium architectural section No 70S 1801 or
523 m 590.03
similar sections.
Anodized Aluminium architectural section No 70S 1202-1
524 m 488.60
or similar sections.
Anodized Aluminium architectural section No 100D - 103
525 m 1,777.06
526 m 1,697.57
527 m 1,637.75
528 m 1,952.14
529 m 2,161.82
530 m 231.19
Anodized Aluminium architectural section No PT-5159 or
531 m 862.68
similar sections.
Anodized Aluminium architectural section No SPR-4521 or
532 m 578.05
similar sections.
Anodized Aluminium architectural section No CA-1009 or
533 m 745.30
similar sections.
534 m 982.85
similar sections.
535 m 953.25
similar sections.
Anodized Aluminium architectural section No 70S-1001-1
536 m 950.71
537 m 929.20
538 m 773.50
Anodized Aluminium architectural section No 70S-1401 or
539 m 652.85
similar sections.
540 m 853.70
similar sections.
541 m 752.85
similar sections.
Anodized Aluminium architectural section No 70SM - 1011
542 m 922.08

2021
Item
No
Rates
Anodized Aluminium architectural section No SPR-105 or
543 m 905.58
similar sections.
Anodized Aluminium architectural section No SPR 110 or
544 m 392.53
similar sections.
Anodized Aluminium architectural section No-SPR-107 or
545 m 545.99
similar sections.
Anodized Aluminium architectural section No-SPR-4521 or
546 m 684.73
similar sections.
Anodized Aluminium architectural section No 70S- 1002 -1
547 m 666.24
Anodized Aluminium architectural section No-70S 1102-1
548 m 476.50
Anodized Aluminium architectural section No-70S 1701A
549 m 875.64
Anodized Aluminium architectural section No-70S 1402-1
550 m 617.81
Anodized Aluminium architecural section DG-01 or similar
551 m 451.88
sections.
Anodized Aluminium Architectural section DG-101 or
552 m 389.80
similar sections.
Anodized Aluminium Architectural section A110- AT or
553 m 470.30
similar sections.
Anodized Aluminium Architectural section 70S - 1701 or
554 m 667.52
similar sections.
Powder coated aluminiumarchitectural section No 100D
555 m 1,943.87
3105 or similar sections.
Powder coated aluminium architectural section No SPR 106
556 m 893.90
Powder coated aluminium architectural section No 70S 1801
557 m 679.63
Powder coated aluminium architectural section No 70S 1202-
558 m 562.54
Powder coated aluminium architectural section No 100D -
559 m 2,047.57
560 m 1,956.69
561 m 1,886.90
562 m 2,250.00
563 m 2,491.31
564 m 266.24
Powder coated aluminium architectural section No PT-5159
565 m 970.37
Powder coated aluminium architectural section No CA-1009
566 m 853.06

2021
Item
No
Rates
567 m 1,131.91
568 m 1,098.21
Powder coated aluminium architectural section No 70S-
569 m 1,095.44
1001-1 or similar sections.
570 m 1,070.94
571 m 891.17
572 m 752.85
573 m 983.62
574 m 867.09
Powder coated aluminium architectural section No 70SM -
575 m 1,061.96
Powder coated aluminium architectural section No SPR-105
576 m 1,044.93
Powder coated aluminium architectural section No SPR 110
577 m 451.88
Powder coated aluminium architectural section No-SPR-107
578 m 610.66
Powder coated aluminium architectural section No-SPR-
579 m 788.86
580 m 780.20
1002 -1 or similar sections.
Powder coated aluminium architectural section No-70S
581 m 549.15
582 m 1,008.69
1701A or similar sections.
583 m 712.25
Powder coated aluminium architecural section DG-01 or
584 m 521.56
similar sections.
Powder coated aluminium Architectural section DG-101 or
585 m 448.69
similar sections.
Powder coated aluminium Architectural section A110- AT
586 m 619.31
Powder coated aluminium Architectural section 70S - 1701
587 m 768.81
Bronze Anodized Aluminium Architectural section No
588 m 1,721.08
100D 3105 or similar sections.
589 m 789.17
SPR106 or similar sections.
Bronze Anodized Aluminium Architectural section No 70S
590 m 601.85

2021
Item
No
Rates
Bronze Anodized Aluminium Architectural section No 70S
591 m 497.57
592 m 1,816.67
100D-103 or similar sections.
593 m 1,728.78
594 m 1,670.37
595 m 2,002.85
596 m 2,201.85
597 m 235.76
Bronze Anodized Aluminium Architectural section No PT-
598 m 875.21
Bronze Anodized Aluminium Architectural section No SPR-
599 m 697.32
Bronze Anodized Aluminium Architectural section No CA-
600 m 773.98
601 m 999.69
602 m 972.07
Bronze Anodized Aluminium Architectural section No 70S-
603 m 997.01
604 m 945.58
605 m 787.89
606 m 664.39
607 m 882.33
608 m 765.53
609 m 938.89
70SM-11011 or similar sections.
610 m 923.19
611 m 399.67
612 m 566.79
613 m 697.32
4521or similar sections.
614 m 709.26
1002-1or similar sections.

2021
Item
No
Rates
615 m 487.89
1102-1or similar sections.
616 m 892.88
1701A or similar sections.
617 m 635.90
618 Cup Nut 8mm Diameter pair 100.00
619 G.I Wall Angels (Ceiling) m 145.00
620 G.I Tee (Ceiling) m 245.00
621 G.I Cross Tee 2' long nr 45.00
622 Roller Beading/Weather strip m 25.00
623 Door Lock for Aluminium Sliding nr 650.00
624 Door Handle BD1068 m 650.00
625 Door Lock for aluminium doors nr 650.00
626 8mm Diameter Tread Bars 5'-0" nr 225.00
627 Hingers 4" x 3" nr 260.00
628 3mm Thickness (8'×4') PVC Ply board (PVC coated) m2 329.86
629 G.S.K Rivets 5/32" x 1/2" nr 2.00
630 Chromium plated Screws 2" x 8" nr 3.50
631 Silicon tube (300g) nr 550.00
632 Flush bolt no.10 nr 450.00
633 Pop Rivet 1. 5/32" x 3/8" nr 1.50
634 GI Channel 6'-0" nr 180.00
635 Bar hingers 8" long pairs 280.00
636 Bar hingers 16" long pairs 400.00
637 Window Rollers nr 80.00
638 Cresant lock nr 150.00
639 Guide nr 2.00
640 Button nr 2.00
641 Gasket (674) m 50.00
642 Screws 8" x 1 1/4" nr 2.50
643 Mohair (Small) m 16.00
644 Mohair (Large) m 30.00
645 Rubber Beadings 455S m 25.00
646 Rubber Beadings 420 m 20.00
647 Rubber Beadings 3303A m 33.30
648 Pop Rivets 1/8" x 3/8" nr 1.00
649 Window Lock nr 250.00
650 Thread bar with 8 Nuts nr 220.00
651 Cladding Board 3mm nr 2,900.00
652 Cladding Board 4mm nr 5,200.00
653 Casement Fastners for Aluminium Windows nr 180.00
GLASS
654 Glass (4.6mm nominal thick) m2 1,162.00
655 Glass Clear (3mm nominal thick) m2 699.66

2021
Item
No
Rates
656 Glass pinhead (3mm nominal thick) m2 839.59
657 Glass Tinted (3mm nominal thick) m2 1,076.40
658 Glass pinhead (5mm nominal thick) m2 1,776.06
659 Glass Tinted (5mm nominal thick) m2 1,829.88
660 Tempered glass 8mm m2 3,767.40
Contruction Chemicals
663 Baralastic 7.2 kg bag 3,600.00
664 Xypex kg 730.54
665 Thoroseal kg 325.00
666 Roofseal m2 810.00
667 Glasscote - 60 m2 550.00
668 Master flow 810 ( Construction grout ,5kg tin) nr 1,100.00
669 Green seal 200mm (fd) Water bar 20m roll nr 19,500.00
670 Water for building works ltr 0.27
General Hardware
671 Brass Barrel Bolt -4" with Screws nr 460.00
672 Brass Barrel Bolt - 6" with Screws nr 490.00
675 Iron Barrel Bolt - 4" with Screws nr 175.00
676 Iron Barrel Bolt - 6" with Screws nr 200.00
677 Iron Oxidized Casement Fastners nr 98.00
678 Iron Oxidized Casement Stays 10" nr 170.00
679 brass circular type Casement Stays- 12" nr 450.00
680 Brass Butt Hinges 4" x 2 1/2" with Screws pair 518.00
681 Iron Oxidized Butt Hinges 4" x 2 1/2" with Screws pair 200.00
682 Lock Mortice Double Hung nr 4,000.00

2021
Item
No
Rates
683 Lock Single Hung nr 3,750.00
684 Night Latch nr 950.00
685 Door Lock (Collapsible) nr 3,500.00
686 Heavy Duty Union Pad Lock 2" nr 1,100.00
687 Gate Lock (Locking divice) nr 250.00
688 Iron Hasp & Staple 6" nr 225.00
689 Draw Ring (1 1/2") nr 78.00
690 Wire Nails kg 200.00
691 Concrete Nails 1" nr 1.25
692 BrassScrews, 1 1/2" nr 18.55
693 Brass Screws 3/4" nr 9.50
694 wire Nails 20mm kg 180.00
695 Iron Screws 1 1/2" nr 5.00
696 Welding Rod kg 315.00
697 Hacksaw blade High Speed nr 175.00
698 Rivet 1/8" x 1/2" nr 1.13
699 Chromium Plated Screws 1 1/2" x 8" nr 4.00
700 Rawl Plug No.8 nr 2.00
701 Rawl Plug No.10 nr 3.28
702 Brass Screws 1" no.08 nr 15.00
703 Iron Screws 1" nr 3.00
704 Iron Screws 3/4" no.08 nr 2.00
705 Iron Screws 1 1/4" no.08 nr 3.50
706 Hold Fast (Heavy) nr 120.00
707 Brass Screws 2 1/2" No.12 nr 57.00
708 Brass Screws 1 1/2" No.08 nr 22.00
709 Nut & Bolt 1 1/2" Long, 1/4" dia. nr 10.00
710 Nut & Bolt 3/8" x 2" nr 40.00
711 Iron Screws 2" No.8 nr 5.00
712 Brass Screws 2"No.08 nr 32.00
713 Brass Screws 2"No.10 nr 40.00

2021
Item
No
Rates
714 Binding Wire 18 BWG kg 250.00
715 Polythene Gauge 700 kg 220.00
716 Polythene Gauge 1000 kg 220.00
717 Weld Mesh (G10) (12"x 7") m2 474.83
718 Steel Jumper kg 570.00
719 Rag Bolt 16mm dia. nr 365.00
720 Rivet 3/16' x 1 3/4" nr 2.50
721 Washer 1/8" kg 550.00
722 Wire Dome. nr 160.00
723 Glue kg 700.00
724 Salt kg 70.00
725 Cotton waste kg 150.00
726 GI Chain kg 140.00
727 Tile mortar 25kg nr 850.00
728 Limpet washer nr 0.50
729 Screw 2" (Chromium plated) nr 3.75
730 Plain GI Sheet G22(Nominal) m2 1,527.13
731 Plain GI Sheet G24(Nominal) m2 1,157.41
732 G22 GI Sheet 8'x 3' (200mm×75mm) (Nominal) nr 3,194.44
733 G24 GI Sheet 8'x 3'(200mm×75mm) (Nominal) nr 2,150.00
734 Solder (Lead) kg 1,304.00
735 GI Hook , Bolt & Nut Washer (Roofing) nr 21.74
736 GI bracket 160mm nr 70.00
737 Calicut tile (Class 01) nr 75.00

738 Ridge tile (Class 01) nr 95.00
739 10mm dia anchor bolts nr 55.00
740 350mm dia.cutting wheel nr 760.00
741 Blasting powder kg 650.00
742 Fuse wire m 42.50
743 Electric detonators nr 25.00
744 Dyna cord m 138.50

2021
Item
No
Rates
745 Gelignite kg 853.00
746 Ammonium nitrate kg 190.00
747 Ordinary Detonator nr 17.50

748 Industrial kerosene oil (Petrolium Coorporation Rates) ltr 70.00
749 ltr 30.00

Mould oil (including transport Rates)
750 Lubricant Oil DS 40 (Petrolium Coorporation Rates) ltr 550.00
751 Auto Diesel (Petrolium Coorporation Rates) ltr 104.00
752 Petrol (Petrolium Coorporation Rates) ltr 137.00
753 Furnace oil for burners ltr 98.00
754 Gas LP Kg 120.00
755 Lubricant (Grease)- Rate at Petrolium Coorporation kg 995.00
756 Baskets nr 400.00
757 Gunny bags (large) nr 70.00
758 Poly sacs (65 kg capacity) nr 80.00
759 Empty tar barrels (180 ltrs) nr 220.00
760 Hard rubber 12 mm thick*75 mm wide m 1,450.00
Polythene 325 mm dia gauge 300 (flat width 505mm
761 kg 350.00
approx)
762 Barricading , lighting and signalling Day 1,622.00
763 Barricading (small work items ) m 65.00
764 Alluminium sheet 24 SWG m2 802.00
765 Adhesive 250 GM tin nr 730.00
Cement sand & water for jointing hume pipes 152 mm
766 nr 25.00
diameter (joint)
Cement sand & water for jointing hume pipes 229 to 610
767 nr 95.00
mm diameter (joint)
768 nr 245.00
diameter (joint)
769 nr 425.00
diameter (joint)
770 Coir rope (for scaffolding 93 sq.m area) nr 50.00
771 Coir string for cutting side drains (per 2.83 cu.m) nr 40.00
772 nr 140.00
Coir string for for fixing scaffolding (per 93 square meters)
Minor repairs parapets with cement sand and water (per 9.29
773 nr 600.00
sq.meters)
Fuel(For loosening road surface in manual breaking 50mm
774 nr 40.00
depth*307 sqm)

2021
Item
No
Rates
775 Fuel Forge etc.(per 2.83 cum blasting) nr 140.00
776 Ladders (per 93 square meters) nr 170.00
777 Paint (for lettering and numbering items) nr 150.00
778 Pegs (for turfing in 19 sq m area) nr 40.00

779 Sand paper and Cotton waste (per 9.29 sq meters) nr 130.00
780 Sharpening scarifier tynes ( for 307 sq.meters) nr 55.00
781 Timber planks & Bamboos (for 93 sqm) nr 900.00
Timber posts horizontal etc (for barricading work in 4
782 nr 350.00
linear meters)
783 Allow water for mixing by machine Cu.m 25.00
784 Allow water for mixing concrete manually Cu.m 25.00
785 Allow water for Gravel Compaction Cu.m 25.00
786 Allow water for Aggregate Compaction Cu.m 25.00
787 Allow for moistening road surface nr 100.00
788 Allow for Water bucket and coir rope nr 100.00
789 Water for general purposes ltr 1.50
790 White washing empty barrels (pen grade) nr 125.00

White washing timber posts horizontals ETC. (in 4 l.m
791 nr 150.00
barricading)
792 Glass Beads kg 195.00
793 Cats eye 100mm*100mm nr 1,775.00
794 75 x 8mm dia. Nuts and Bolts nr 65.00
795 Saw Dust m3 150.00
Mild Steel Formwork for Standard Boundary Marker Stone
796 nr 4,392.00
(750mm x 200mm x 75mm) for 15 gurd stone.
Roller Door
797 Zn/Al powder coated roller door m2 7,407.50
798 Box covering L shape m 1,759.25
799 Box covering U shape m 2,731.50
800 Facia m 1,064.81
801 Box covering with roof L m 6,157.41
802 Box covering with roof U m 7,129.63
803 Box covering with roof Facia m 5,462.96

2021
Item
No
Rates
804 Normal rollar door motar with 2nr remotes nr 35,000.00
Gate accessories and complete gate

805 Brass nut (100mm ) No 3,600.00
806 Brass nut (150mm ) No 3,600.00
807 Brass nut (225mm ) No 6,600.00
808 Brass nut (300mm ) No 6,600.00
809 Brass nut (375mm ) No 6,600.00
810 Brass nut (450mm ) No 7,800.00
811 Brass nut (600mm ) No 7,800.00
812 Brass nut (750mm ) No 11,400.00
813 Brass nut (900mm ) No 11,400.00
814 Housing (100mm) No 4,200.00
815 Housing (150mm) No 4,200.00
816 Housing (225 mm) No 6,600.00
817 Housing (300mm) No 6,600.00
818 Housing (375mm) No 6,600.00
819 Housing (450mm) No 7,800.00
820 Housing (600mm) No 7,800.00
821 Housing (750mm) No 10,200.00
822 Housing (900mm) No 10,200.00
823 Base plate (100mm) No 1,020.00
824 Base plate (150mm) No 1,020.00
825 Base plate (225mm) No 1,800.00
826 Base plate (300mm) No 1,800.00
827 Base plate (375mm) No 1,800.00
828 Base plate (450mm) No 2,040.00
829 Base plate (600mm) No 2,400.00

2021
Item
No
Rates
830 Base plate (750mm) No 3,600.00
831 Base plate (900mm) No 3,600.00
832 Closing plate (100mm) No 1,020.00
841 Key (100mm) No 900.00
842 Key (150mm) No 900.00
843 Key (225mm) No 1,200.00
844 Key (300mm) No 1,200.00
845 Key (375mm) No 1,200.00
846 Key (450mm) No 1,800.00
847 Key (600mm) No 1,800.00
848 Key (750mm) No 3,000.00
849 Key (900mm) No 3,000.00
850 Bush (100mm) No 300.00
851 Bush (150mm) No 300.00
852 Bush (225mm) No 480.00
853 Bush (300mm) No 480.00
854 Bush (375mm) No 480.00
855 Bush (450mm) No 720.00
856 Bush (600mm) No 720.00
857 Bush (750mm) No 720.00

2021
Item
No
Rates
858 Bush (900mm) No 780.00
859 Pin (100mm) No 420.00
860 Pin (150mm) No 420.00
861 Pin (225mm) No 540.00
862 Pin (300mm) No 540.00
863 Pin (375mm) No 600.00
864 Pin (450mm) No 840.00
865 Pin (600mm) No 840.00
866 Pin (750mm) No 1,020.00
867 Pin (900mm) No 1,020.00
868 Rug bolt (100mm) No 120.00
869 Rug bolt (150mm) No 120.00
870 Rug bolt (225mm) No 180.00
871 Rug bolt (300mm) No 180.00
872 Rug bolt (375mm) No 240.00
873 Rug bolt (450mm) No 240.00
874 Rug bolt (600mm) No 240.00
875 Rug bolt (750mm) No 240.00
876 Rug bolt (900mm) No 240.00
877 Locking arrangement (100mm) No 600.00
882 Locking arrangement (450mm) No 1,200.00

2021
Item
No
Rates
886 Spindle with thread (100mm) No 4,200.00
895 100 mm CI Gate Complete Set No 22,500.00


2021
Item
No
Rates
ELECTRICAL ITEMS
1000 1/1.13 mm (1 mm2) Cu/PVC/PVC single core cable m 22.50
1001 7/0.53 mm (1.5mm2) Cu/PVC/PVC single core cable m 43.89
1002 7/0.67 mm (2.5mm2) Cu/PVC/PVC single core cable m 64.95
Cu/PVC/PVC Cable - Twin cable
1008
2 x 7/0.53 mm (1.5mm2) Cu/PVC/PVC twin cable m 83.43
1009
2 x 7/0.67 mm (2.5mm2) Cu/PVC/PVC twin cable m 121.67
1010
2 x 7/0.85 mm (4mm2) Cu/PVC/PVC twin cable m 191.76
1011
2 x 7/1.04 mm (6 mm2) Cu/PVC/PVC twin cable m 279.86
1012
1013
Cu/XLPE/PVC Cable - single core cable
1014 19/1.53mm (35 mm2)Cu/XLPE/PVC single core cable m 825.42
1015 19/1.78mm (50 mm2 )Cu/XLPE/PVC single core cable
m 1,095.46
1016 19/2.14 mm (70 mm2) Cu/XLPE/PVC single core cable
m 1,797.18
1017 37/1.78 mm (95 mm2) Cu/XLPE/PVC single core cable
m 2,327.78
Cu/PVC Earth Cable
1018 7/0.67 mm ( 2.5mm2) Cu/PVC earth cable m 56.76
1019 7/0.85 mm (4mm2) Cu/PVC earth cable m 95.88
1023 19/ 1.35 mm (25mm2) Cu/PVC earth cable m 601.48

2021
Item
No
Rates
1024 19/1.53mm (35mm2) Cu/PVC earth cable m 777.31
1025 19/1.78mm (50mm2) Cu/PVC earth cable m 1,043.80
Cu/XLPE/SWA/PVC cable(Armoured Cable)
1026 (2X25mm2) Cu/XLPE/SWA/PVC armoured cable
m 2,356.48
m 3,125.00
m 3,254.63
m 3,939.81
m 5,393.52
m 7,319.44
m 10,101.85
m 12,282.41
Cu/ PVC/SWA/PVC Cables ( Armoured Cable)
1034 (2X1.5 mm2) Cu/PVC/SWA/PVC armoured cable m 300.93
1035 (2X2.5mm2) Cu/PVC/SWA/PVC armoured cable m 388.89
1036 (2X4mm2) Cu/PVC/SWA/PVC armoured cable m 814.81
1038 (2X10mm2) Cu/PVC/SWA/PVC armoured cable m 1,245.37
Data & Telephone cable
1046 5U/UTP AWG 24 Cat 5E PVC m 68.55
1047 6U/ UTP AWG 24 Cat 6E PVC m 88.39
1048 2X0.50 mm Telephone cable single pair m 26.25
1049 4X0.50mm Telephone cable two pair m 44.31
Flexible cables
1050 32/0.20 mm (1 mm2) Cu/PVC/PVC 2core flexible cord
m 67.08
1051 32/0.20 mm (1 mm2) Cu/PVC/PVC 3core flexible cord
m 109.21
Arial Bundle Cable ( ABC)
1052 3X 35mm2 Al/XLPE+ N 54.6mm2 ABC m 481.48
1055 3X 95mm2 Al/XLPE+ N 70mm2 ABC m 953.70

2021
Item
No
Rates
1056 3X 120mm2 Al/XLPE+ N 70mm2 ABC m 1,111.11
1057 3X 35mm2 Al/XLPE+ N 54.6mm2 +16mm2 ABC m 527.78
1060 3X 95mm2 Al/XLPE+ N 70mm2 +16mm2 ABC m 1,000.00
1061 3X 120mm2 Al/XLPE+ N 70mm2 +16mm2 ABC m 1,157.41
MCBs & MCCBs
1062 1P MCB(6A,10A,16A,20A,25A,32A) nr 560.00
1063 2P MCB(6A,10A,16A,20A,25A,32A) nr 1,470.00
1064 40A 2P MCB nr 1,625.00
1065 63A 2P MCB nr 3,394.00
1066 3P MCB(6A,10A,16A,20A,25A,32A) nr 2,630.00
1067 40A 3P MCB nr 2,944.00
1068 63A 3P MCB nr 5,315.00
1069 4P MCB(6A,10A,16A,20A,25A,32A) nr 4,320.00
1070 40A 4P MCB nr 5,155.00
1071 63A 4P MCB nr 7,610.00
1072 4P MCCB - Fixed type
(16A,20A,25A,32A,40A,50A,63A,80A,100A) nr 15,870.00
1073 63A, 3P MCCB(Fixed type) nr 7,670.00
1074 100A, 3P MCCB(Fixed type) nr 7,670.00
1075 100A-125A,,3P MCCB(Adjustable type) nr 14,670.00
1076 25kA 4P MCCB - Adjustable type (25-32A,32-40A,40-
50A,50-63A,63-80A,80-100A) nr 18,560.00
1077 100A-125A,25kA,4P MCCB(Adjustable type) nr 24,000.00
Isolators
1083 40A 2P ISOLATOR nr 1,775.00
1084 63A 2P ISOLATOR nr 2,075.00
1085 40A ,3P ISOLATOR nr 1,980.00
1086 63A ,3P ISOLATOR nr 2,320.00
1087 100A ,3P ISOLATOR nr 4,240.00
1088 40A ,4P ISOLATOR nr 4,460.00
1089 63A ,4P ISOLATOR nr 4,510.00
1090 100A ,4P ISOLATOR nr 5,830.00
RCCB (RCD)
1091 40A , 30mA , 2P RCD nr 4,585.00
1092 63A , 30mA , 2P RCD nr 6,115.00
1093 40A , 30mA , 4P RCD nr 7,260.00
1094 63A , 30mA , 4P RCD nr 9,832.00
1095 100A , 30mA , 4P RCD nr 20,259.00
1096 40A , 100mA , 2P RCD nr 5,394.00
1097 63A , 100mA , 2P RCD nr 7,416.00
1098 40A , 100mA , 4P RCD nr 7,260.00

2021
Item
No
Rates
1099 63A , 100mA , 4P RCD nr 9,832.00
1100 100A , 100mA , 4P RCD nr 18,495.00
1101 63A , 300mA , 2P RCD nr 7,120.00
1102 63A , 300mA , 4P RCD nr 9,832.00
1103 100A ,300mA , 4P RCD nr 18,495.00
Conduits ,Casing & Relevant Items
1104 1/2" (16mm) PVC Conduits m 24.07
1105 3/4" (20mm) PVC Conduits m 29.40
1106 1" (25mm) PVC Conduits m 39.58
1107 1 1/4 " (32mm) PVC Conduits m 81.48
1108 1 1/2 " (40mm) PVC Conduits m 113.19
1109 2" (50mm) PVC Conduits m 127.31
1110 Conduit clips nr 1.85
1111 Junction Box nr 13.89
1112 16mm x 12.5mm Casing m 49.49
1113 20 mm x 12.5mm Casing m 59.39
1114 25mm x 16mm Casing m 71.84
1115 32mm x 16mm Casing m 102.81
1116 40mm x 16mm Casing m 128.99
1117 25mm x 25mm Casing m 77.16
1118 50mm x 50mm Casing m 312.90
1119 100mm x 50mm Casing m 551.40
1120 Conduit Accessories Item 35.00
1121 Casing Accessories Item 70.00
Plastic enclosures
1122 2 Pole surface mounted type plastic enclosure nr 152.78
1123 4 Pole surface mounted type plastic enclosure nr 175.93
1124 6 way surface mounted type plastic enclosure nr 531.48
1129 16 way surface mounted type plastic enclosure nr 1,921.30
1130 18 way surface mounted type plastic enclosure nr 1,921.30
1131 2 raw surface box nr 2,900.00
1132 3 raw surface box nr 4,521.30
1133 8 way flush type plastic enclosure nr 1,039.81
Powder coated metal enclosures with cover plates

1138
Powder coated metal enclosure for 1 no. of 2 Pole Isolator
nr 1,148.15
1139
nr 1,268.52

2021
Item
No
Rates
1140
nr 1,388.89
1141 Powder coated metal enclosure with cover plate for 3 Pole
MCCB nr 2,722.22
1142 Powder coated metal enclosure with cover plate for 4 Pole
MCCB nr 2,351.85
1143 1 row 6 way - surface mounted type powder coated metal
enclosure with cover plate nr 3,425.93
1152 3 row 42 way + space for MCCB - surface mounted type
powder coated metal enclosure with cover plate nr 12,592.59
1153 3 row 42 way + space for 4P MCB - surface mounted type
powder coated metal enclosure with cover plate nr 11,111.11
1155 200X200X150 surface mounted type powder coated metal
enclosure with cover plate
nr 7,638.89
enclosure with cover plate
nr 8,000.00

2021
Item
No
Rates
Distribution Board Accessories

1181 100/5 A Current Transformers nr 694.44
1182 Indicator lamps (LED) nr 92.59
1183 Bus bar support (Insulators) nr 138.89
1184 20mm spiral m 92.59
1185 1″ X 1/8″ Cu bus bar m 1,466.89
1186 1″ X 1/4″ Cu bus bar m 2,907.58
1187 Shunt coil (Moellor or equivalent) nr 6,944.44
1188 EFR 4 current transformer type nr 12,962.96
1189 Selector switch for distribution pannel nr 1,388.89
1190 Volt meter for pannel (analogue) nr 879.63

2021
Item
No
Rates
1191 Amphere meter for pannel (analogue) nr 879.63
1192 Digital V/A/Hz anlysiser for distribution panel nr 5,092.59
1193 Din rail m 277.78
1194 2A HRC fuse with din rail mount base for distribution
panels nr 324.07
1195 40 kA 2 pole din rail mount surge arrestor nr 17,555.56
1199 32A 100kA/120kA HRC fuse with base nr 869.57
1200 63A 100kA/120kA HRC fuse with base nr 869.57
1201 100A 100kA/120kA HRC fuse with base nr 1,739.13
1202 40A 2 pole change over (MCB type) nr 1,851.85
Dinrail Mount Terminal Block ( Bus bar splitter Box)
1206 80A Dinrail mount terminal block ( Bus bar splitter box )
nr 601.85
nr 694.44
nr 879.63
nr 1,342.59
Cable Lugs
1210 120 mm2 cable lug nr 277.78
1211 95 mm2 cable lug nr 190.74
1212 70 mm2 cable lug nr 111.11
1213 50 mm2 cable lug nr 87.96
1220 2.5 mm2 cable lug nr 9.26
1221 1.5 mm2 cable lug nr 12.04
1223 35 mm2 Bimetalic lugs nr 324.07
1224 50 mm2 Bimetalic lugs nr 370.37
End Caps
1225 50 mm2 end cap nr 23.15
1226 35 mm2 end cap nr 18.52
1227 25 mm2 end cap nr 13.89
1228 16 mm2 end cap nr 9.26

2021
Item
No
Rates
1229 10 mm2 end cap nr 7.41
1230 6 mm2 end cap nr 4.63
1231 4 mm2 end cap nr 4.63
1232 2.5 mm2 end cap nr 3.70
1233 1.5 mm2 end cap nr 3.70
1234 1 mm2 end cap nr 3.24
1235 Bus bar terminals for MCB nr 9.26
1236 Installation Accessories Item 70.00
Socket outlets & Relative Items
1237 Sunk box (Switch box) nr 64.81
1238 Double sun box nr 74.07
1239 13A socket outlet nr 495.37
1240 13A socket outlet with neon indicator nr 509.26
1241 13A plug top nr 208.33
1242 Industrial socket outlets 32A, 16A 3pin nr 694.44
1243 Industrial socket outlets 32A, 16A 5pin nr 787.04
1244 Telephone socket outlet ( RJ 11 ) nr 648.15
1245 Data socket outlet (RJ 45) nr 1,944.44
1246 Telephone+Data outlet nr 1,898.15
1247 USB charger outlet nr 1,185.19
1248 Multi 1A USB charger nr 2,314.81
1249 Blank Plate nr 120.37
Lamp fittings, Bulbs & Relative items

1250 11W CFL Spiral type - Orange / Phillips or equivalent nr 388.89
1254 11W CFL U type - Orange / Phillips or equivalent nr 296.30
1258 14W/15W CFL Globe - Orange / Phillips or equivalent nr 509.26
1259 200mm conical polycarbonate shade nr 185.19
1260 Bulk head lamp ( water tight) - small nr 601.85
1261 7W LED globe type bulb with SLS 1458 nr 333.33
1264 6 W LED ceiling lamp (surface mounted type) - with 2 year nr
warranty - Green/Orange or equivalent 879.63
1265 12 W LED ceiling lamp (surface mounted type) - with 2 nr
year warranty - Green/Orange or equivalent 1,157.41

2021
Item
No
Rates
1269 6W LED ceiling lamp (ceiling embedded type) - with 2 year nr
787.04
warranty - Green/Orange or equivalent
1270 12W LED ceiling lamp (ceiling embedded type) - with 2 nr
1,018.52
year warranty - Green/Orange or equivalent
1,296.30
1,851.85
1273 40W LED ceiling lamp (ceiling embedded type) - with 2 nr 5,370.37
1274 10W LED flood light - with 2 year warranty nr 787.04
1275 20W LED flood light - with 2 year warranty nr 2,777.78
Fluorescent fitting with electronic ballast
1279 1200mm X 300 mm louver fitting with 36W fluorescent nr 4,259.26
lamp and electronic ballast (High quality)
1280 600X600 mm louver fitting with 18W X 3 fluorescent lamps nr
4,490.74
and electronic ballasts (High quality)
1281 1200mm 36W X 1 fluorescent lamp fitting with prismatic nr 1,388.89
diffuser and electronic ballast
diffuser and electronic ballasts (High quality)
diffuser and electronic ballast (High quality)
1284 1200mm 36W X 1 fluorescent lamp fitting with opel white nr 2,314.81
diffuser and electrical ballast (Imported quality)
diffuser and electronic ballasts (High quality)
diffuser and electronic ballast (High quality)
Lamp Accessories
1287 Fluorescent electronic ballast 18W nr 416.67
1288 Fluorescent electronic ballast 36 W nr 416.67
1289 GI chain for hang of Floursent lamp nr 27.78
1290 Cup hook for hang of Floursent lamp nr 9.26
1291 Connector bar 5A nr 37.04
1292 Ceiling rose (2 terminals) nr 92.59

2021
Item
No
Rates
1293 Round block nr 18.52
1294 Pendent bulb holder - pin type nr 87.96

1295 Pendent bulb holder - screw type nr 203.70
1296 Angle batten holder - pin type nr 111.11
1297 Angle batten holder - screw type nr 222.22
1298 1 gang switch nr 134.26
1303 1 gang two way switch nr 208.33
1304 2 gang two way switch nr 416.67
1305 Intermediat Switch nr 833.33
1306 Key Card Switch nr 3,240.74
1307 400W dimmer switch nr 833.33
1308 20A 2P switch with neon indicator nr 782.41
Fans & Relative Items (Japanese or equivalent quality)
1309 Ceiling fan 1400mm diameter - Classic (Type 1) - SLS 814 nr 8,100.00
1310 Ceiling fan 1400mm diameter - Ring (Type 1) - SLS 814 nr 8,600.00
1311 Wall fan 400mm diameter (Type 1) nr 12,000.00

1312 Wall fan 400mm diameter with remote controller (Type 1) nr 16,200.00
1313 Exhaust fan 200mm diameter with auto shutter (Type 1) nr 7,600.00
1315 Orbit fan (Type 1) nr 16,000.00
1316 Five step fan regulator (Type 1) nr 879.63
Fans & Relative Items (Indian or equivalent quality)

1317 Ceiling fan 1400mm diameter (Type 2) nr 5,555.56
1318 Wall fan 400mm diameter (Type 2) nr 5,324.07
1321 Orbit fan (Type 2) nr 6,018.52
1322 Five step fan regulator (Type 2) nr 879.63
1323 Fan hook nr 138.89
Items for Earthling System

1324 2" GI Pipe (Heavy) m 1,611.00
1325 16 mm - diameter Cu earth electrode nr 694.44
1326 Earth clip nr 92.59

2021
Item
No
Rates
Air Conditioners
1327 Supply and fixing 12000 Btu Split type Air Conditioner nr 94,073.15
(Non-Invertor type)
(Non-Invertor type)
(Non-Invertor type)
1330 Supply and fixing 36000 Btu Split type Air Conditioner - nr 285,000.00
Ceiling Suspending (Non-Invertor type)
(Invertor type )
(Invertor type )
(Invertor type )
1334 Supply and fixing 36000 Btu Split type Air Conditioner - nr 402,776.85
Ceiling Suspending (Invertor type)
Data Communication system Rack & Accessorise

1335 19" Powder Coated Wall Mounting Rack with Glass Door (
425mm depth ) -3U nr 7,870.37
425mm depth ) -5U nr 12,500.00
425mm depth ) -7U nr 13,425.93
425mm depth ) -10U nr 17,700.00
425mm depth ) -12U nr 10,212.96
425mm depth ) -16U nr 12,444.44
425mm depth ) -21U nr 14,481.48
Network Switches
1342 Network Switch - 24 Port Category 6 , 10/100 Mbps
Network switch. nr 12,500.00
1343 Network Switch - 24 Port + POE Category 6, 10/100 Mbps
1344 Network Switch - 24 Port Category 6 , 10/100/1000 Mbps
1345 Network Switch - 24 Port + POE Category 6 , 10/100/1000
Mbps Network switch. nr 69,444.44
1346 Network Switch - 16 Port Category 6 , 10/100 Mbps
1347 Network Switch - 16 Port + POE Category 6, 10/100 Mbps
1348 Network Switch - 16 Port Category 6 , 10/100/1000 Mbps

2021
Item
No
Rates
1349 Network Switch - 16 Port + POE Category 6 , 10/100/1000
Mbps Network switch. nr 30,092.59
1350 24 Port Cat 6 Patch Panel with Keystones nr 8,527.00
1351 Category 6 Patch cord 1m nr 365.74
1352 Category 6 Patch cord 2m nr 527.78
Slotted Cable Trays And Accessorise ( Powder Coated)

1353 150 mm X 50 mm Slotted Cable Trays m 1,135.09
1354 150 mm X 50 mm L Bend nr 1,055.55
1355 150 mm X 50 mm T way Joint nr 1,842.59
1356 300 mm X 75 mm Slotted Cable Trays m 2,236.01
1357 300 mm X 75 mm L Bend nr 2,685.00
1358 300 mm X 75 mm T Way Joint nr 3,601.00

2021
Item
No
Rates
Transport Committee Report -2021
Plant & Machinary
2001 Concrete Mixer 400 Liters Day 5,500.00
2002 Porker Vibrator 90 Kg petrol ( Without operator. ) Day 2,156.28
2003 Poker vibrator - Electric ( Without operator. ) Day 2,156.28
2004 Plate vibrator (90 Kg) ( Without operator. ) Day 3,167.00
2005 Water Pump 2" dia ( Without operator. ) hour 266.00
2006 Water pump 4" dia (With Operator) hour 1,175.26
2007 Tar Boiler (Heating with firewood) ( Without operator. ) Day 600.00
2008 Sand/chip spreader-propelled Day 25,000.00
2009 Sand/chip spreader-towed Day 2,500.00
2010 Emulsion sprayer self prop.(4000 litres) Day 26,495.56
2011 Concrete mixer with weigh batcher 114/10 * Day 7,256.00
2012 Hand held Breaker (Demolisher) (less operater) Day 506.65
2013 Bitumen sprayer (Less Operator) Day 4,000.00
2014 Water tank+50mm pump (Less Operator) Day 1,765.00
2015 Transport of premix by dump truck-Rate for 1 km MT/km 18.90
2016 Transport of Emulsion (100ltr) km 4.00
2017 Asphalt paver (crawler) hour 7,839.00
2018 Asphalt paver (Wheel) hour 8,724.90
2019 Tanker only (20000 litres) hour 311.00
2020 Baby dumper 0.75 cu.m (Less Operator) hour 1,260.00
2021 Prime mover old (for 20000 L tanker) hour 3,500.00
2022 Trolley emulsion (less operator) hour 114.70
2023 Sprayer emulsion hand cart hour 815.91
2024 Bitumen distributor 750 litres hour 1,700.00
2025 Tank truck bitumen 10000 Ltr hour 4,442.95
2026 Crusher stone 40t/h hour 11,493.26
2027 Track drill crawler hour 1,808.50
2028 Slurry sealing Machine hour 13,399.51
2029 Asphalt plant 60t/h hot mix hour 20,618.02
2030 Cold mix plant 15ton hour 10,651.02
2031 Lorry 17 ton Self Loading (wet) km 173.15
2032 Emulsion Tank Truck (8000litres) km 134.37
2033 Excavator Mobile hour 3,100.00
2034 Excavator 120 hour 3,500.00
2035 Mobile Crane 25T hour 8,341.80
2036 Mobile Crane 30T hour 10,549.76
2037 Pneumatic roller 8 -10 ton hour 4,142.00
2038 Smooth /Road Roller 8 - 10 ton static Day 14,660.00
2039 Vibrating Roller 0.5 - 1.0 ton Day 6,865.00
2040 Vibrating roller 6 - 7 ton tendum Day 22,160.00
2041 Vibrating roller10 ton smooth Day 27,488.00

2021
Item
No
Rates
2042 Tractor& Trailor 0.75 Cube Day 6,465.00
2043 Farm tractor and broom hour 808.46
2044 Tracror with water bowser hour 808.46
2045 Tractor with emulison bowser hour 818.00
2046 Motorgrader (65 Hp) 10 feet blade Day 23,520.00
2047 Motorgrader (120 Hp) 12 feet blade Day 36,320.00
2048 Backhoe JCB (90 Hp) & 4WD Day 25,577.04
2049 Backhoe Loader (90 Hp) & 2WD Day 20,000.00
2050 Wheel Loader 1.4 -1.7 Cu. m. Bucket Day 24,476.00
2051 Wheel loader (2.7-3.1 cu.m) Day 41,689.76
2052 Wheel loader (2.0-2.3 cu.m) Day 36,454.80
2053 Dozer (Crawler Tractor)D-4 D-41 (80-100Hp) hour 4,571.00
2054 Sludge pump 4"(With Operator) hour 1,580.00
2055 Water Bowser 6000 Liters Day 11,000.00
2056 Electric welding plant with generator Day 9,000.00
2057 Road marker Hand cart gas heater hour 1,906.00
2058 Air compressor 750 CFM hour 4,000.00
2059 Air compressor 250 CFM hour 2,586.00
2060 Lorry/Tipper/Dump truck (exceeding 10km) for 1km Rate Cu.m/km 28.95
2061 Lorry/Tipper/Dump truck Rate for up to 10km Cu.m/km 40.00
2062 Lorry/Tipper/Dump truck (3 T) Day 8,500.00
2063 Lorry 3 tons(2.5 cu.m)(beyond 10km) km 57.50
2066 Pick up 2WD/Car/Van(beyond 10km) km 41.00
2067 Pickup 4WD km 60.00
2068 Vibrating rammer (60kg)(Less Operator) Day 3,900.00
2069 Pickup truck 2WD km 60.00
Transport of materials 25m to 100m by any means ( Incl.
2070 Loading and Unloading) Cu.m 465.10
Transport 100m to 0.5km by any means (Excluding
2071 Loading) Cu.m 258.60
Transport 0.5km to 1.0km by any means (Excluding
2072 Loading) Cu.m 277.05
Transport of each subsequent 1.0km from 1.0 - 8.0km. By
2073 any means : (Excluding Loading) Cu.m 43.10
Transport of each subsequent 1.0km beyond 8km. By any
2074 means : (Excluding Loading) Cu.m 28.95
Transport of material in bulk excluding loading(for distance
2075 less than or equal 3km) Cu.m 89.15
2076 from 3km upto 10km distance) Cu.m/km 29.70
2077 more than 10km) Cu.m/km 26.20

Chief Secretary’s Oﬃce
Central Province

BSR 2021

Uploaded by

Copyright:

Available Formats

BSR 2021

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

BSR 2021

Uploaded by

Copyright:

Available Formats

General Notes Provincial Schedule of Rates 2021

Provincial Price Committee 2021

15. Your attention is drawn to construction related clauses of the Construction

Provincial Price Committee 2021

Highway Schedule of Rates -70 to 97

Irrigation Schedule of Rates -98 to 102

DEPARTMENT OF ENGINEERING SERVICES

Prepared by Department of Engineering Services, Central Provincial Council

 This BSR is prepared according to SRI LANKA STANDARD 573:1999

 Overheads & Profit margin is taken as 26 % of the basic rates.

 Working Rates = Basic Rates + Overheads & Profit Margin.

 Separate preliminary bill shall be included.(Applicable site overhead percentages for

4 Security for construction sites 0.8

13 Head office and rent, lights, telephone, stationary, suppliers, 0.6

Item Site Overhead Percentage

4 Security for construction sites 0.5

 Doors, windows or partitions fully glazed 1.25

 Allowances to be made in the rates for the works in upper floors

Ground to 1st Ground to Ground to

These rates are limited only for four storied building.

Size of extrusion in member of Doors, Windows and Partitions.

Cable colour Code

 SI – British conversion factors

Structural timber for Roof work, ceiling frames and Partitions

Floor Boarding Teak, Kumbuk

Beadings Lunumidella, Mahogany

Super Luxury Class :

Special Class Upper :

All species not otherwise classified.

Demolishing Hacking up & clearing debris away of

Demolishing bricks walls above 225mm thick inclusive

Removing & clearing debries away Corrugated sheets,

Provincial Price Committee 2021 Page 1

Removing & clearing debries away Corrugated sheets,

Removing & clearing debries away tiles calicut or half

Removing & clearing debries away tiles calicut or half

Removing & clearing debries away tiled roof with

Provincial Price Committee 2021 Page 2

Cement and sand rough plaster, breaking the damaged

Floor re-rendering with 1:3 cement and sand after

Provincial Price Committee 2021 Page 3

Suppling & fixing barbed wire 14 gauge 4 Points,on

REPAIRS AND MAINTENANCE

Brick work/ Masonry with available material

Shifting and re-laying after cleaning calicut tiles. (For

Replacing Asbestos roofing sheets with new sheets on

Provincial Price Committee 2021 Page 4

Fixing available steel purlins on roof structures

Provincial Price Committee 2021 Page 5

Repairing door & window frames using treated kempas,

Provincial Price Committee 2021 Page 6

Excavation and levelling site in soft rock involving

Excavation in foundations in normal earth, depth greater

Provincial Price Committee 2021 Page 7

Excavation in wells / pits in normal earth 1.0m to 2.0m

Excavation in wells / pits in normal earth 2.0m to 3.0 m

Excavation in wells / pits in normal earth 3.0m to 4.0m

Breaking out existing material

Earth work Support

Bailing out and cleaning of well total depth up to 4.8m