Manual 21CA80VE
Manual 21CA80VE
com
e-mail:http://www.LGEservice.com/techsup.html
COLOR TV
SERVICE MANUAL
CHASSIS : MC-019A
MODEL : RF/RT-20/21CA80VE/VQ/VW
MODEL : RF/RT-14/21CA80M/MX
MODEL : CF-21CA810EX/RF-21CB90VQ
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
Contents ................................................................................................................. 2
Specifications ..................................................................................................... 6
Adjustment ............................................................................................................11
-2 -
An lsolation Transformer should always be used during always perform an AC leakage current check on the exposed
the servicing of a receiver whose chassis is not isolated from metallic parts of the cabinet, such as antennas, terminals, etc.,
the AC power line. Use a transformer of adequate power rating to be sure the set is safe to operate without damage of
as this protects the technician from accidents resulting in electrical shock.
personal injury from electrical shocks.
Leakage Current Cold Check(Antenna Cold Check)
It will also protect the receiver and it's components from being With the instrument AC plug removed from AC source,
damaged by accidental shorts of the circuitary that may be connect an electrical jumper across the two AC plug prongs.
inadvertently introduced during the service operation. Place the AC switch in the on positioin, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
If any fuse (or Fusible Resistor) in this TV receiver is blown, ohm-meter lead in turn to each exposed metallic parts such as
replace it with the specified. antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
When replacing a high wattage resistor (Oxide Metal Film measured resistance should be between 1MΩ and 5.2MΩ.
Resistor, over 1W), keep the resistor 10mm away from PCB. When the exposed metal has no return path to the chassis the
reading must be infinite.
Keep wires away from high voltage or high temperature parts. An other abnormality exists that must be corrected before the
receiver is returned to the customer.
Due to high vacuum and large surface area of picture tube,
extreme care should be used in handling the Picture Tube. Leakage Current Hot Check (See below Figure)
Do not lift the Picture tube by it's Neck. Plug the AC cord directly into the AC outlet.
Do not use a line Isolation Transformer during this check.
X-RAY Radiation Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
between a known good earth ground (Water Pipe, Conduit, etc.)
Warning: and the exposed metallic parts.
Measure the AC voltage across the resistor using AC
The source of X-RAY RADIATION in this TV receiver is the voltmeter with 1000 ohms/volt or more sensitivity.
High Voltage Section and the Picture Tube. Reverse plug the AC cord into the AC outlet and repeat AC
For continued X-RAY RADIATION protection, the voltage measurements for each esposed metallic part. Any
replacement tube must be the same type tube as specified in voltage measured must not exceed 0.75 volt RMS which is
the Replacement Parts List. corresponds to 0.5mA.
In case any measurement is out of the limits sepcified, there is
possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
To determine the presence of high voltage, use an accurate
high impedance HV meter. Leakage Current Hot Check circuit
1.5 Kohm/10W
-3 -
-4 -
-5 -
O Tuning range
For TV
Band For CATV
B/G D/K I/I NTSC
VHF-Low Ch2-4 Ch1-5 S1'-S3', S1
Ch2-13 S2-S10,
VHF-High Ch5-12 Ch6-12 Ch4-13
S11-S20
Hyper S21-S41
UHF Ch21-69 Ch14-69
O External In/Output
Audio-In:0.5Vrms!3dB,over 10Kohm
Audio-Out:0.5Vrms!3dBb,below 1Kohm
Video-In/Out:1Vp-p!3dB,75ohm
DVD In Y: 1Vp-p!3dB
Pb,Pr : 0.7Vp-p!3dB
-6 -
All the functions can be controlled with the remote control handset.
Some functions can also be adjusted with the buttons on the front
panel of the set.
1 2 3 2. NUMBER BUTTONS
switches the set on from standby or directly select a number.
2 4 5 6
3. MENU (or INDEX)
7 8 9 selects a menu.
selects an index page in the teletext mode (only TELETEXT
MENU/INDEX TV/AV
0 models).
3 11
TV
4. EYE/ (option)
4
EYE/ PR ( ) I/II/
12 *
switches the eye function on or off.
(With TELETEXT)
-7 -
11. TV/AV
selects TV or AV mode.
clears the menu from the screen.
switches the set on from standby.
COLOURED BUTTONS : These buttons are used for teletext (only VOL VOL
5 OK
TELETEXT models) or programme edit.
Q.VIEW PR ( ) LIST
6 13
Battery installation
The remote control handset is powered by two AAA type batteries.
To load the batteries, turn the remote control handset over and
open the battery compartment. Install two batteries as indicated by
the polarity symbols ( + and - ) marked inside the compartment. PSM SSM/ SLEEP
8 14
/ 15
16
PICTURE SOUND
TURBO/
9
(Without TELETEXT)
-8 -
(Side panel)
1 23 4 5 9
-9 -
CPT
board
Remove
Screws
Main
PCB
- 10 -
- 11 -
TXT-L 0 WEST-EU
(ARAB) 1 ARABIC White level
GND for dc
TXT-L 0 WEST-EU
(FARSI) 1 FARSI
14” OTHERS
DC 130V!3 V DC 140V!3 V
O AGC Adjustment (SERVICE 1)
O White Balance Adjustment.(LINE SVC-0)
Test Point : AGC TP (C101)
Adjust : Remote Controller NOTE : This adjustment should be performed after screen voltage
adjustment.
1) Connect RF signal (70dB!0.2dB) and turn on the TV. 1) Tune the TV set to receive an 100% white pattern.
¡ Standard adjustment Channel 2) Press OK(V) buttons on TV set and remote controller at the
- EU 05 Ch. (frf = 175.25MHz) same time to get into SVC mode.
2) Press the OK buttons on TV set and Remote Controller at the 3) Press Yellow button on remote controller. (Standard mode)
same time to get into SVC-0 mode. 4) Press Channel UP/DOWN button for desirous function
3) Press the Channel UP/DOWN button on the Remote adjustment.
Controller several times to find AGC??. 5) Adjust VOL+ or VOL-button in each status of "RG--"/"BG--" for
4) Press the Volume UP/DOWN button until the AGC Voltage is X=272!8, Y=288!8 with color analyzer.(Europe Model :
the same as the Table below. X=288!8, Y=295!X=272!8, 11,000K)
5) Press the OK(V) button to memorize the data.
Status Initial Data Remark
Tuner P/N 6700VPF009G 6700VPF016A
RG 31
Marker LG Innotek(W/S TUNER) DAEWOO(W/S TUNER)
GG 31
AGC Voltage 2.7! 0.05V 2.7! 0.05V
BG 31
Tuner P/N 6700VPF009S
BLO-R 31
Marker LG Innotek(TBS TUNER)
- 12 -
VL 31 31 31
VA 31 31 31
VS 31 31 31
HS 31 31 31
SC 25 25 25
VA (Vertical Amplitude)
Adjust so that the circle of a digital circle pattern may be
located within the effective screen of the CPT.
VS (Vertical Shift)
Adjust so that the horizontal center line of a digital circle
pattern is in accord with geometric horizontal center of the
CPT.
HS (Horizontal Shift)
Adjust so that the vertical center line of a digital circle pattern is
in accord with geometric vertical center of the CPT.
- 13 -
Caution:
Convergence and Purity have been factory aligned. Do not 5. Reconnect the internal degaussing coil.
attempt to tamper with these alignments.
However, the effects of adjacent receiver components, or 6. Position the beam bender locking rings at the 9 o'clock
replacement of picture tube or deflection yoke may require the position and the other three pairs of tabs (2,4 and 6 pole
need to readjust purity any convergence. magnets) at the 12 o'clock position.
6-POLE
,
,,,,,,,,,,
,,,,,, ,,,,,,,,,,,,, 4-POLE
,,,,,,,,,, ,,,,,,,,
,
X-AXIS YOKE MAGNET
,
,,,,,,,,, ,,,,,,,
,,,,,, ,,,,
POSITIONING
(L/R PURITY)
RUBBER
WEDGES PURITY MAGNET
4-POLE
GLASS CLOTH TAPE CONVERGENCE MAGNET ASSEMBLY
CONVERGENCE MAGNET ASSEMBLY
¡ Purity Adjustment
This procedure DOES NOT apply to bonded yoke and picture 7. Perform the following steps, in the order given, to prepare the
tube assemblies. receiver for the purity adjustment procedure.
The instrument should be at room temperature (60 degrees F or
above) for six (6) hours and be operating at low beam current a. Face the receiver in the "magnetic north" direction.
(dark background) for approximately 20 to 30 minutes before
performing purity adjustments. b. Externally degauss the receiver screen with the television
power turned off.
CAUTION: Do not remove any trim magnets that may be
attached to the bell of the picture tube. c. Turn the television on for approximately 10 seconds to
perform internal degaussing and then turn the TV off.
1. Remove the AC power and disconnect the internal
degaussing coil. d. Unplug the internal degaussing coil. This allows the
thermistor to cool down while you are performing the purity
2. Remove the yoke from the neck of the picture tube. adjustment. DO NOT MOVE THE RECEIVER FROM ITS
"MAGNETIC NORTH" POSITION.
3. If the yoke has the tape version beam bender, remove it and
replace it with a adjustable type beam bender (follow the e. Turn the receiver on and obtain a red raster by increasing
instructions provided with the new beam bender) the red bias control (CW) and decreasing the bias controls
for the remaining two colors (CCW).
4. Replace the yoke on the picture tube neck, temporarily
remove the three (3) rubber wedges from the bell of the f. Attach two round magnets on the picture tube screen at 3
picture tube and then slide the yoke completely forward. o'clock and 9 o'clock positions, approximately one (1) inch
from the edge of the mask (use double-sided tape).
- 14 -
MAGNETS
RED RED
8. Referring to above, perform the following two steps: 6. Reconnect the internal degaussing coil and apply AC power.
a. Adjust the yoke Z-axis to obtain equal blue circles.
b. Adjust the appropriate beam bender tabs to obtain correct 7. Turn the receiver on for 10 seconds to perform internal
purity (four equal circles). degaussing and then turn the receiver off again.
9. After correct purity is set, tighten the yoke clamp screw and 8. Unplug the internal degaussing-coil.
remove the two screen magnets.
9. Turn on the receiver, connect a signal generator to the VHF
10. Remove the AC power and rotate the receiver 180 degrees antenna terminal and apply a crosshatch signal.
(facing "magnetic south").
Caution: During the convergence adjustment procedure, be
11. Reconnect the internal degaussing coil. very careful not to disturb the purity adjustment tabs
are accidentally move, purity should be confirmed
12. Turn the receiver on for 10 seconds (make sure the receiver before proceeding with the convergence adjustments.
came on) to perform internal degaussing, and then turn the
receiver off. Note: Make sure the focus is set correctly on this instrument
before proceeding with the following adjustment.
13. Unplug the internal degaussing coil.
10. Converge the red and blue vertical lines to the green vertical
14. Turn on the receiver and check the purity by holding one (1) line at the center of the screen by performing the following
round magnet at the 3 o'clock and a second round magnet at steps (below TABLE).
9 o'clock position. If purity is not satisfactory, repeat steps 8 a. Carefully rotate both tabs of the 4-pole ring magnet
through 14. simultaneously in opposite directions from the 12 o'clock
position to converge the red and blue vertical lines.
15. Turn off the receiver and reconnect the internal degaussing b. Carefully rotate both tabs of the 6-pole ring magnet
coil. simultaneously in opposite directions form the 12 o'clock
position to converge the red and blue (now purple)
vertical lines with the green vertical line.
¡ Convergence Adjustment
11. Converge the red and blue horizontal with the green line at
Caution: This procedure DOES NOT apply to bonded yoke and the center of the screen by performing the following steps.
picture tube assemblies. (below TABLE)
Do not use screen magnets during this adjustment a. Carefully rotate both tabs of the 4-pole ring magnet
procedure. Use of screen magnets will cause an simultaneously in the same direction (keep the spacing
incorrect display. between the two tabs the same) to converge the red and
blue horizontal lines.
1. Remove AC power and disconnect the internal degaussing b. Carefully rotate both tabs of the 6-pole ring magnet
coil. simultaneously in same direction (keep the spacing
between the two tabs the same) to converge the red and
2. Apply AC Power and set the brightness to the Picture Reset blue (now purple) horizontal lines with the green
condition. Set the Color control to minimum. horizontal line.
c. Secure the tabs previsouly adjusted by locking them in
3. Make a horizontal line. place with the locking tabs on the beam bender.
4. Adjust the Red, Green and Blue Bias controls to get a dim
white line.
- 15 -
B B
OPPOSITE OR
R R
4
POLE
SAME B R OR B R
B B
OPPOSITE OR
R R
6
POLE
SAME B R OR B R
GREEN
GREEN
ADJUSTMENT
VIEWING ADJUSTMENT RED
AREA BLUE RED VIEWING
AREA
RED
BLUE RED
GREEN
RED BLUE
TV
SCREEN
GREEN
12. While watching the 6 o'clock positions on the screen, rock the 17. Temporarily place a rubber wedge at the 5 o'clock and 7
front of the yoke in a vertical (up/down) direction to converge o'clock positions to hold the horizontal position of the yoke.
the red and blue vertical lines. (Fig upper left) 18. Check the 3 o'clock and 9 o'clock areas to confirm that the
13. Temporarily place a rubber wedge at the 12 o'clock position red and blue vertical lines are converged. If the lines are not
to hold the vertical position or the yoke. converged, slightly offset the horizontal tilt of the yoke (move
14. Check the 3 o'clock and 9 o'clock areas to confirm that the red the temporary rubber wedges if necessary) to equally
and blue horizontal lines are converged. balance the convergence error of the horizontal lines at 6
If the lines are not converged, slightly offset the vertical tilt of the o'clock and 12 o'clock and the vertical lines at 3 o'clock and 9
yoke (move the rubber wedge if necessary) to equally balance the o'clock.
convergence error of the horizontal lines at 3 o'clock and 9 o'clock 19. Using a round magnet confirm purity at the center, right and
and the vertical lines at 6 o'clock and 12 o'clock. left sides and corners. See Purity Adjustment Procedure.
15. Place a 1.5 inch piece of glass tape over the rubber foot at 20. Reconfirm convergence and apply a 1.5 inch piece of glass
the rear of the 12 o'clock wedge. tape over the rubber foot at the rear of the 5 o'clock and the 7
16. While watching the 6 o'clock and 12 o'clock areas of the o'clock wedges.
screen, rock the front of the yoke in the horizontal (left to
right) motion to converge the red and blue horizontal lines.
(Fig. upper right)
- 16 -
- 17 -
RGB IK EXT
SIF Audio-in CVBS SFE 5.74M
OUT Video-in
UOC V_DY
VIDEO 44 Audio Out °‹ Thai
SIF 32
TDA9361(TXT) Opt. Va VERTICAL AMP
SW1 IC03 SCL Vb LA7840
EEPROM TDA9381(Non-TXT) Va 22
BLOCK DIAGRAM
Audio(Mono)
(TV OUT)
8V Video-OUT(TV/MNT OUT) FBT
EXT.RGB 8 ABL
From
IC844 A(R/L)-OUT (MNT/TV-OUT)
A1(R/L)-IN 9 HEATER
EXT Video
5V V-OUT
3 B+
From UOC
5.1V Video(Game) Audio(Game) DVD Y / Game Video Collector
EXT Video(To UOC #42)
Y/Pb/Pr 1
SDA
SCL 3, 4, 5 1 2 2 4 7
HIC01 Rear_AV(1) DVD IC591
Game Pack(Game Opt) ( SCART / PHONE) (FLAT OPT.) LA7016(DVD / GameOpt))
HDT
TUNER PJ201
EXPLODED VIEW
943
913
400
150
153
170
112 174
550
520
120
310
700
340 530
320
121
330
350
354
- 18 -
PART NO
LOCA. NO DESCRIPTIONS
14” 20” 21”
- 19 -
170
112
174
300
520
120
122
310
340 540
320
700
330
121
350
354
- 20 -
- 21 -
- 22 -
C201 0CE227DD618 220UF STD 10V M FL TP5 C524 0CN1030F679 10000P 16V M Y TA52
C202 0CN4710K519 470P 50V K C529 0CE225CK636 2.2UF SHL SD 50V
C207 0CN4710K519 470P 50V K C530 0CQ1041N509 0.1U 100V K POLY TP
C208 0CE226DF618 22UF STD 16V M FL TP5 C534 0CN1030F679 10000P 16V M Y TA52
C209 0CE226DF618 22UF STD 16V M FL TP5 C538 0CF4741L438 0.47UF D 63V 5% TP 5 M/PE NI
C210 0CN1030F679 10000P 16V M Y TA52 C540 0CN2230H949 22000P 25V Z
C212 0CN4710K519 470P 50V K C541 0CN2230H949 22000P 25V Z
C221 0CE475DK618 4.7UF STD 50V 20% FL TP5 C542 0CN2230H949 22000P 25V Z
C222 0CE475DK618 4.7UF STD 50V 20% FL TP5 C548 0CN8210K519 820P 50V K B TA52
C223 0CE475DK618 4.7UF STD 50V 20% FL TP5 C549 0CQ4721N509 0.0047U 100V K POLY TP
C255 0CN1020K519 1000P 50V K C551 0CX4700K409 47P 50V J SL TA52
C258 0CN1030F679 10000P 16V M Y TA52 C561 0CE107DD618 100UF STD 10V M FL TP5
C259 0CN1030F679 10000P 16V M Y TA52 C573 0CE476DF618 47UF STD 16V M FL TP5
C260 0CE226DF618 22UF STD 16V M FL TP5 C574 0CQ1021N509 0.001U 100V K POLY TP
C301 0CQ1041N509 0.1U 100V K POLY TP C593 0CE475DK618 4.7UF STD 50V 20%
C302 0CQ3931N509 0.0390UF 100V K PE TP C594 0CQ1041N509 0.1U 100V K POLY TP
C303 0CK1810W515 180P 500V K B TS C595 0CE475DK618 4.7UF STD 50V 20%
C304 0CE107DJ618 100UF STD 35V M FL TP5 C601 0CE226DF618 22UF STD 16V M FL TP5
C307 0CQ6821N509 0.0068U 100V K POLY TP C602 0CF2241L438 0.22UF D 63V 5% TP 5 M/PE NI
C401 181-013P MPP 400V 0.33UF J “ 181-007F MPE ECQ-V1H224JL3
“(20”) 181-013C MPP 200V 0.39UF J C603 0CQ4721N509 0.0047U 100V K POLY TP
“(14”) 181-013C MPP 200V 0.39UF J “ 0CQ6821N509 0.0068U 100V K POLY TP
C402 0CE475DP618 4.7UF STD 160V 20% FL TP 5 C605 0CQ4721N509 0.0047U 100V K POLY TP
C403 181-015E MPP 1600V 0.0068UF H “ 0CQ6821N509 0.0068U 100V K POLY TP
“(14”) 181-015D MPP 1600V 0.0062UF H C606 0CF2241L438 0.22UF D 63V 5% TP 5 M/PE NI
“(20”) 181-015G MPP 1600V 0.0077UF H C607 0CN1030F679 10000P 16V M Y TA52
C404 0CK8210W515 820P 500V K B TS C612 0CE477DH618 470UF STD 25V M FL TP5
C405 181-091U R 220PF 2KV 10%,-10% R/TP TP7. C631 0CF4741L438 0.47UF D 63V 5% TP 5 M/PE NI
“(14”) 181-091W R 470PF 2KV 10%,-10% C632 0CF4741L438 0.47UF D 63V 5% TP 5 M/PE NI
C441 0CQ1531N509 0.015U 100V K POLY TP C633 0CE107DD618 100UF STD 10V M FL TP5
C443 0CE477DH618 470UF STD 25V M FL TP5 C634 0CN1030F679 10000P 16V M Y TA52
C444 0CE475DR618 4.7UF STD 250V 20% FL TP 5 C635 0CE106DF618 10UF STD 16V M FL TP5
C446 0CE477DH618 470UF STD 25V M FL TP5 “ 0CE476DF618 47UF STD 16V M FL TP5
C447 0CQ3321N509 0.0033U 100V K POLY TP C636 0CQ6821N509 0.0068U 100V K POLY TP
C449 181-009V PP 200V 0.047UF K C637 0CF1541L438 0.15UF D 63V 5% TP 5 M/PE NI
C452 0CE106DK618 10UF STD 50V M FL TP5 C638 0CQ5621N509 0.0056U 100V K POLY TP
C501 0CF2241L438 0.22UF D 63V 5% TP 5 M/PE NI C639 0CQ5621N509 0.0056U 100V K POLY TP
C502 0CN1030F679 10000P 16V M Y TA52 C640 0CF1541L438 0.15UF D 63V 5% TP 5 M/PE NI
C503 0CE107DD618 100UF STD 10V M FL TP5 C641 0CQ6821N509 0.0068U 100V K POLY TP
C504 0CE225DK618 2.2UF STD 50V 20% FL TP 5 C642 0CQ5621N509 0.0056U 100V K POLY TP
C505 0CQ2221N509 0.0022U 100V K POLY TP C643 0CF4741L438 0.47UF D 63V 5%
C506 0CE105DK618 1UF STD 50V M FL TP5 C644 0CQ4731N509 0.047U 100V K POLY TP
C507 0CQ2221N509 0.0022U 100V K POLY TP C645 0CF4741L438 0.47UF D 63V 5%
C508 0CE476DF618 47UF STD 16V M C646 0CF4741L438 0.47UF D 63V 5% TP 5 M/PE NI
C509 0CE106DF618 10UF STD 16V M FL TP5 C653 0CE475DK618 4.7UF STD 50V 20
C511 0CE105DK618 1UF STD 50V M FL TP5 C655 0CE475DK618 4.7UF STD 50V 20
C512 0CN1020K519 1000P 50V K B TA52 C801 0CE107BJ618 100UF KME 35V M FL TP5
C513 0CN1020K519 1000P 50V K B TA52 C802 181-091U R 220PF 2KV 10%,-10% R/TP TP7.
C514 0CQ1041N455 0.1000UF 100V J PP NI FM7.5 C803 0CK4710W515 470PF 500V K B TR
C515 0CQ2231N509 0.022U 100V K POLY TP C804 0CQ1041N509 0.1U 100V K POLY TP
C516 0CQ3321N509 0.0033U 100V K POLY TP C805 0CK10102515 100PF 2KV K
C517 0CE106DF618 10UF STD 16V M FL TP5 C806 181-001V CE 450V 220UF M LUG(85)
- 23 -
- 24 -
R09 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R219 0RD1801F609 1.8K OHM 1/6 W 5.00% TA52
R10 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R220 0RD4702F609 47K OHM 1/6 W 5.00% TA52
R11 0RD1001F609 1K OHM 1/6 W 5.00% TA52 R221 0RD1201F609 1.2K OHM 1/6 W 5.00% TA52
R12 0RD1001F609 1K OHM 1/6 W 5.00% TA52 R222 0RD4701F609 4.7K OHM 1/6 W 5.00% TA52
R13 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R223 0RD3901F609 3.9K OHM 1/6 W 5.00% TA52
R14 0RD1603F609 160K OHM 1/6 W 5.00% TA52 R224 0RD1201F609 1.2K OHM 1/6 W 5.00% TA52
“ 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R225 0RD3901F609 3.9K OHM 1/6 W 5.00% TA52
R15 0RD1001F609 1K OHM 1/6 W 5.00% TA52 R226 0RD4701F609 4.7K OHM 1/6 W 5.00% TA52
R16 0RD4701F609 4.7K OHM 1/6 W 5.00% TA52 R227 0RD1201F609 1.2K OHM 1/6 W 5.00% TA52
R17 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R228 0RD1801F609 1.8K OHM 1/6 W 5.00% TA52
R18 0RD1203F609 120K OHM 1/6 W 5.00% TA52 R251 0RD1300F609 130 OHM 1/6 W 5.00% TA52
R19 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R254 0RD2200H609 220 OHM 1/2 W 5.00% TA52
R21 0RD2201F609 2.2K OHM 1/6 W 5.00% TA52 “ 0RD2200A609 220 OHM 1/2 W(7.0) 5.00% TA52
R22 0RD3902F609 39K OHM 1/6 W 5.00% TA52 R255 0RD2200H609 220 OHM 1/2 W 5.00% TA52
R23 0RD2200F609 220 OHM 1/6 W 5.00% TA52 “ 0RD2200A609 220 OHM 1/2 W(7.0) 5.00% TA52
R25 0RD1201F609 1.2K OHM 1/6 W 5.00% TA52 R301 0RD0101F609 1 OHM 1/6 W 5.00% TA52
R26 0RD1601F609 1.6K OHM 1/6 W 5.00% TA52 R302 0RN1501F409 1.5K OHM 1/6 W 1.00% TA52
R27 0RD3601F609 3.6K OHM 1/6 W 5.00% TA52 “(20”) 0RN1201F409 1.2K OHM 1/6 W 1.00% TA52
R29 0RD1201F609 1.2K OHM 1/6 W 5.00% TA52 R304 0RD0221H609 2.2 OHM 1/2 W 5.00% TA52
R30 0RD3601F609 3.6K OHM 1/6 W 5.00% TA52 “(20”) 0RD0201H609 2 OHM 1/2 W 5.00% TA52
R31 0RD1601F609 1.6K OHM 1/6 W 5.00% TA52 R305 0RD0271H609 2.7 OHM 1/2 W 5.00% TA52
R41 0RD6200F609 620 OHM 1/6 W 5.00% TA52 R306 0RS2700K607 270 OHM 2 W 5.00% TA62
R51 0RD1000F609 100 OHM 1/6 W 5.00% TA52 “(20”) 0RS2200K607 220 OHM 2 W 5.00% TA62
R52 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R307 0RD1501F609 1.5K OHM 1/6 W 5.00% TA52
R101 0RD1002F609 10K OHM 1/6 W 5.00% TA52 “(20”) 0RD1201F609 1.2K OHM 1/6 W 5.00% TA52
R102 0RD1202F609 12K OHM 1/6 W 5.00% TA52 R310 0RD1801F609 1.8K OHM 1/6 W 5.00% TA52
R103 0RD1802F609 18K OHM 1/6 W 5.00% TA52 R311 0RD4701H609 4.7K OHM 1/2 W 5.00% TA52
R107 0RS0272J607 27 OHM 1 W 5.00% TA62 “ 0RD4701A609 4.7K OHM 1/2 W(7.0) 5.00% TA52
R108 0RD0392F609 39 OHM 1/6 W 5.00% TA52 R312 0RD2201F609 2.2K OHM 1/6 W 5.00% TA52
R109 0RD0562F609 56 OHM 1/6 W 5.00% TA52 R313 0RD1002F609 10K OHM 1/6 W 5.00% TA52
R110 0RD1201F609 1.2K OHM 1/6 W 5.00% TA52 R401 0RD1501H609 1.5K OHM 1/2 W 5.00% TA52
R111 0RD3601F609 3.6K OHM 1/6 W 5.00% TA52 “ 0RD1501A609 1.5K OHM 1/2 W(7.0) 5.00% TA52
R112 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R402 0RS2702K607 27K OHM 2 W 5.00% TA62
R113 0RD6800F609 680 OHM 1/6 W 5.00% TA52 R442 0RD5100H609 510 OHM 1/2 W 5.00% TA52
R114 0RD0272F609 27 OHM 1/6 W 5.00% TA52 R444 0RD0392H609 39 OHM 1/2 W 5.00% TA52
R115 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R446 0RD1001F609 1K OHM 1/6 W 5.00% TA52
R116 0RD6801F609 6.8K OHM 1/6 W 5.00% TA52 R447 0RD3301F609 3.3K OHM 1/6 W 5.00% TA52
R117 0RD2201F609 2.2K OHM 1/6 W 5.00% TA52 “(14”) 0RD3901F609 3.9K OHM 1/6 W 5.00% TA52
R118 0RD2201F609 2.2K OHM 1/6 W 5.00% TA52 “(20”) 0RD3001F609 3K OHM 1/6 W 5.00% TA52
R201 0RD0912F609 91 OHM 1/6 W 5.00% TA52 R450 0RD4701H609 4.7K OHM 1/2 W 5.00% TA52
R204 0RD0752F609 75 OHM 1/6 W 5.00% TA52 R451 0RD1200H609 120 OHM 1/2 W 5.00% TA52
R205 0RD0752F609 75 OHM 1/6 W 5.00% TA52 “(14”) 0RD1500H609 150 OHM 1/2 W 5.00% TA52
R206 0RD0752F609 75 OHM 1/6 W 5.00% TA52 “(21”) 0RD0822H609 82 OHM 1/2 W 5.00% TA52
R207 0RD0752F609 75 OHM 1/6 W 5.00% TA52 R453 0RS4702H609 47K OHM 1/2 W 5.00% TA52
R208 0RD1001F609 1K OHM 1/6 W 5.00% TA52 “(14”) 0RS5102H609 51K OHM 1/2 W 5.00% TA52
R212 0RD5101F609 5.1K OHM 1/6 W 5.00% TA52 “(20”) 0RS3302H609 33K OHM 1/2 W 5.00% TA52
R213 0RD5101F609 5.1K OHM 1/6 W 5.00% TA52 R455 0RS2702K607 27K OHM 2 W 5.00% TA62
R214 0RD5101F609 5.1K OHM 1/6 W 5.00% TA52 R456 0RS2702H609 27K OHM 1/2 W 5.00% TA52
R215 0RD5101F609 5.1K OHM 1/6 W 5.00% TA52 “(14”) 0RS3302H609 33K OHM 1/2 W 5.00% TA52
R216 0RD2202F609 22K OHM 1/6 W 5.00% TA52 “(20”) 0RS5102H609 51K OHM 1/2 W 5.00% TA52
R217 0RD2201F609 2.2K OHM 1/6 W 5.00% TA52 R501 0RD2202F609 22K OHM 1/6 W 5.00% TA52
R218 0RD1001F609 1K OHM 1/6 W 5.00% TA52 R502 0RD1002F609 10K OHM 1/6 W 5.00% TA52
- 25 -
R503 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R670 0RD2000F609 200 OHM 1/6W 5
R504 0RN3902F409 39K OHM 1/6 W 1.00% TA52 R801 0RD2701F609 2.7K OHM 1/6 W 5.00% TA52
R505 0RD6800F609 680 OHM 1/6 W 5.00% TA52 R802 0RD2201F609 2.2K OHM 1/6 W 5.00% TA52
R506 0RD1001F609 1K OHM 1/6 W 5.00% TA52 R803 0RD1001F609 1K OHM 1/6 W 5.00% TA52
R518 0RD3302F609 33K OHM 1/6 W 5.00% TA52 R804 0RD4701F609 4.7K OHM 1/6 W 5.00% TA52
R521 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R805 180-A01P 0.13 OHM 2 W 5% TA62 RWR
R522 0RD2702F609 27K OHM 1/6 W 5.00% TA52 R806 0RD2401F609 2.4K OHM 1/6 W 5.00% TA52
R523 0RD1003F609 100K OHM 1/6 W 5.00% TA52 R808 0RD4701F609 4.7K OHM 1/6 W 5.00% TA52
R524 0RD3001F609 3K OHM 1/6 W 5.00% TA52 R809 0RS4702K607 47K OHM 2 W 5.00% TA62
R525 0RD3900F609 390 OHM 1/6 W 5.00% TA52 R812 0RK8204H609 8.2M OHM 1/2 W 5.00% TA52
R526 0RD2001F609 2K OHM 1/6 W 5.00% TA52 R813 0RD1002F609 10K OHM 1/6 W 5.00% TA52
R537 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R815 0RD0751H609 7.5 OHM 1/2 W 5.00% TA52
R538 0RD1000F609 100 OHM 1/6 W 5.00% TA52 “ 0RD0751A609 7.5 OHM 1/2 W(7.0) 5.00% TA52
R539 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R816 0RD2001F609 2K OHM 1/6 W 5.00% TA52
R540 0RD1000F609 100 OHM 1/6 W 5.00% TA52 R901 0RD2200F609 220 OHM 1/6 W 5.00% TA52
R542 0RD1002F609 10K OHM 1/6 W 5.00% TA52 R902 0RD2200F609 220 OHM 1/6 W 5.00% TA52
R544 0RD2701F609 2.7K OHM 1/6 W 5.00% TA52 R903 0RD2200F609 220 OHM 1/6 W 5.00% TA52
R548 0RD2200F609 220 OHM 1/6 W 5.00% TA52 R904 0RD2200F609 220 OHM 1/6 W 5.00% TA52
R551 0RD1200F609 120 OHM 1/6 W 5.00% TA52 R905 0RD2200F609 220 OHM 1/6 W 5.00% TA52
R552 0RD1200F609 120 OHM 1/6 W 5.00% TA52 R906 0RD1000F609 100 OHM 1/6 W 5.00% TA52
R553 0RD3300F609 330 OHM 1/6 W 5.00% TA52 R907 0RD1000F609 100 OHM 1/6 W 5.00% TA52
R554 0RD4701F609 4.7K OHM 1/6 W 5.00% TA52 R908 0RD1000F609 100 OHM 1/6 W 5.00% TA52
R555 0RD1800F609 180 OHM 1/6 W 5.00% TA52 R909 0RS1501H609 1.5K OHM 1/2 W 5.00% TA52
R556 0RD1500F609 150 OHM 1/6 W 5.00% TA52 R910 0RS1501H609 1.5K OHM 1/2 W 5.00% TA52
R557 0RD4701F609 4.7K OHM 1/6 W 5.00% TA52 R911 0RS1501H609 1.5K OHM 1/2 W 5.00% TA52
R558 0RD4701F609 4.7K OHM 1/6 W 5.00% TA52 R912 0RD2204H609 2.2M OHM 1/2 W 5.00% TA52
R572 0RD5600F609 560 OHM 1/6 W 5.00% TA52 “ 0RD2204A609 2.2M OHM 1/2 W(7.0) 5.00% TA52
R573 0RD2403F609 240K OHM 1/6 W 5.00% TA52 RC801 180-822N RWR 7W 1.0 OHM J PD
R601 0RD4701F609 4.7K OHM 1/6 W 5.00% TA52 RV01 0RD1002F609 10K OHM 1/6W 5
R602 0RD1002F609 10K OHM 1/6 W 5.00% TA52 RV02 0RD4701F609 4.7K OHM 1/6W 5
R604 0RD2401F609 2.4K OHM 1/6 W 5.00% TA52
SWITCH
“ 0RD5601F609 5.6K OHM 1/6 W 5.00% TA52
“ 0RD3301F609 3.3K OHM 1/6 W 5.00% TA52 SW01 140-315A SWITCH,TACT SKHV17910B LG C&D NON 12V
R606 0RD1102F609 11K OHM 1/6 W 5.00% TA52 SW02 140-315A SWITCH,TACT SKHV17910B LG C&D NON 12V
“ 0RD1302F609 13K OHM 1/6 W 5.00% TA52 SW03 140-315A SWITCH,TACT SKHV17910B LG C&D NON 12V
“ 0RD2001F609 2K OHM 1/6 W 5.00% TA52 SW04 140-315A SWITCH,TACT SKHV17910B LG C&D NON 12V
R608 0RD2401F609 2.4K OHM 1/6 W 5.00% TA52 SW05 140-315A SWITCH,TACT SKHV17910B LG C&D NON 12V
“ 0RD3301F609 3.3K OHM 1/6 W 5.00% TA52 SW06 140-315A SWITCH,TACT SKHV17910B LG C&D NON 12V
R609 0RD1102F609 11K OHM 1/6W 5% SW07 140-315A SWITCH,TACT SKHV17910B LG C&D NON 12V
“ 0RD1302F609 13K OHM 1/6W 5% SW08 140-315A SWITCH,TACT SKHV17910B LG C&D NON 12V
R610 0RD4702F609 47K OHM 1/6 W 5.00% TA52 SW801 6600VM2002A SWITCH,PUSH SDKEA3 IEC 250V 8A HORIZO
R611 0RD4702F609 47K OHM 1/6 W 5.00% TA52
FILTER & CRYSTAL
R631 0RD1302F609 13K OHM 1/6 W 5.00% TA52
R632 0RD1000F609 100 OHM 1/6 W 5.00% TA52 FB801 125-022R FILTER,BI3857 FEELUX 5.7X3.6MM AXIAL
R633 0RD1000F609 100 OHM 1/6 W 5.00% TA52 FB802 125-022R FILTER,BI3857 FEELUX 5.7X3.6MM AXIAL
R634 0RD1302F609 13K OHM 1/6 W 5.00% TA52 FB803 125-022R FILTER,BI3857 FEELUX 5.7X3.6MM AXIAL
R651 0RD4700F609 470 OHM 1/6 W 5.00% TA52 L611 125-022R FILTER,BI3857 FEELUX 5.7X3.6MM AXIAL
“ 0RD1500F609 150 OHM 1/6 W 5.00% TA52 T551 166-C02D FILTER,TPSRD6M00B00-A0 TPS6.0MB-TF21
R652 0RD3300F609 330 OHM 1/6 W 5.00% TA52 T552 166-C04C FILTER,TPWRD5M50B02-A0 TPWA02B-TF21 M
R657 0RD4300F609 430 OHM 1/6 W 5.00% TA52 T553 6200VST001C FILTER,XT4.5MB BAOTONG 4.5MHZ 166-C02
“ 0RD1001F609 1K OHM 1/6 W 5.00% TA52 T801 150-F06J FILTER,SQE2930 18MH PHY TURN
R660 0RD4702F609 47K OHM 1/6W 5 “ 150-F06W FILTER,SQE2930 36MH
- 26 -
ACCESSORIES
A1 3828VA0270F MANUAL,OWNERS NON LG AR/EN
A2 6710V00090C REMOTE CONTROLLER W/TXT GS
A2 6710V00090V REMOTE CONTROLLER W/O TXT
A2 6710V00090D REMOTE CONTROLLER,W/O TXT LG
A2 6710V00074B REMOTE CONTROLLER W/O TXT LG LGEIN
A2 6710V00090A REMOTE CONTROLLER W/TXT LG
A3 5010V00005C ANTENNA 2 POLE 3 SECTION 700MM 650MM
MISCELLANEOUS
SK901 6620VBC003A SOCKET,CPT PCS030A 8PIN 14/360
“ 6620VBA003A SOCKET,CPT PCS031A 7PIN
TH801 163-054F THERMISTOR,PTC J502P84D140M290Q
TU101 6700VPF016A TUNER,DT5-BF70D PARTSNIC MULTI FS W/
“ 6700VPF009Z TUNER,TAEM-G001D LG PAL
“ 6700VPF009T TUNER,TUMLF4EG-775F2
VD801 164-003G VARISTOR,TVR621D14A 620V 10% U
PA01 6726VV0006H REMOTE CONTROLLER RECEIVER 38KHZ
PJ201 6612VJH004H JACK,RCA PJ6056A 6P STEREO MC-
“ 6612VJH004F JACK,RCA PJ6056F
“ 6612VJH023A JACK,RCA PPJ126A A/V 11P
“ 381-091A SOCKET,S-091A
PJ202 6613V00006E JACK ASSY PJ6062E A/V 3P+E/P W
“ 6613V00006C JACK ASSY PJ6062C A/V 2P
- 27 -