DT 50 Py 10

website:http://biz.LGservice.
com
e-mail:http://www.LGEservice.com/techsup.html
PLASMA TV
SERVICE MANUAL
CHASSIS : AF-046A
MODEL : DT-50PY10
CAUTION
BEFORE SERVICING THE CHASSIS,
READ THE SAFETY PRECAUTIONS IN THIS MANUAL.
Downloaded from www.Manualslib.com manuals search engine

CONTENTS
SAFETY PRECAUTIONS ...................................................................................3
DESCRIPTION OF CONTROLS ........................................................................ 4
SPECIFICATIONS .............................................................................................. 8
ADJUSTMENT INSTRUCTIONS ........................................................................9
TROUBLE SHOOTING GUIDE ..........................................................................12
BLOCK DIAGRAM .............................................................................................26
EXPLODED VIEW ..............................................................................................28
EXPLODED VIEW PARTS LIST ........................................................................29
REPLACEMENT PARTS LIST...........................................................................30
SCHEMATIC DIAGRAM ........................................................................................
PRINTED CIRCUIT BOARD ..................................................................................
-2 -

SAFETY PRECAUTIONS
IMPORTANT SAFETY NOTICE

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in
the Schematic Diagram and Replacement Parts List.
It is essential that these special safety parts should be replaced with the same components as recommended in this manual to
prevent X-RADIATION, Shock, Fire, or other Hazards.
Do not modify the original design without permission of manufacturer.
General Guidance Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.
An isolation Transformer should always be used during Do not use a line Isolation Transformer during this check.
the servicing of a receiver whose chassis is not isolated from Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor
the AC power line. Use a transformer of adequate power rating between a known good earth ground (Water Pipe, Conduit, etc.)
as this protects the technician from accidents resulting in and the exposed metallic parts.
personal injury from electrical shocks. Measure the AC voltage across the resistor using AC
voltmeter with 1000 ohms/volt or more sensitivity.
It will also protect the receiver and it's components from being Reverse plug the AC cord into the AC outlet and repeat AC
damaged by accidental shorts of the circuitry that may be voltage measurements for each exposed metallic part. Any
inadvertently introduced during the service operation. voltage measured must not exceed 0.75 volt RMS which is
corresponds to 0.5mA.
If any fuse (or Fusible Resistor) in this monitor is blown, replace In case any measurement is out of the limits specified, there is
it with the specified. possibility of shock hazard and the set must be checked and
repaired before it is returned to the customer.
When replacing a high wattage resistor (Oxide Metal Film
Resistor, over 1W), keep the resistor 10mm away from PCB.
Keep wires away from high voltage or high temperature parts. Leakage Current Hot Check circuit
Due to high vacuum and large surface area of picture tube,

AC Volt-meter
extreme care should be used in handling the Picture Tube.
Do not lift the Picture tube by it's Neck.
Good Earth Ground

such as WATER PIPE,
Leakage Current Cold Check(Antenna Cold Check) To Instrument's CONDUIT etc.
With the instrument AC plug removed from AC source, 0.15uF
exposed
connect an electrical jumper across the two AC plug prongs. METALLIC PARTS
Place the AC switch in the on position, connect one lead of
ohm-meter to the AC plug prongs tied together and touch other
ohm-meter lead in turn to each exposed metallic parts such as 1.5 Kohm/10W
antenna terminals, phone jacks, etc.
If the exposed metallic part has a return path to the chassis, the
measured resistance should be between 1MΩ and 5.2MΩ.
When the exposed metal has no return path to the chassis the
reading must be infinite.
An other abnormality exists that must be corrected before the
receiver is returned to the customer.
-3 -

DESCRIPTION OF CONTROLS
Remote Control Key Functions

- When using the remote control aim it at the remote control sensor of the set.
- There's maybe a defect in consecutive operation of remote control in specified brightness according to this set feature.
displays the selected device. POWER

TV
switches the set on from standby or
VCR off to standby.
MODE DVD
selects another device. CABLE MULTIMEDIA
HDSTB selects Component 1/2, RGB-DTV,
D/A TV AUDIO RGB-PC, DVI-DTV or DVI-PC modes.
selects analogue or digital mode. switches the set on from standby.
MODE ARC (Aspect Ratio Control)
D/A TV POWER
changes the picture format.
TV/AV
selects the remote operating mode. MULTIMEDIA ARC
switches the set on from standby. TV/AV
TEXT
These buttons are used for teletext.
NUMBER buttons For further details, see the ‘Teletext’
1 2 3 section.
SLEEP switches the subtitle on or off in Digital
sets the sleep timer. 4 5 6 mode.
Note : In teletext mode, the PIP PR +/-,
7 8 9 SWAP and PIP INPUT buttons are used
MUTE SLEEP TEXT
switches the sound on or off. for teletext function.
0
VOL +/- (Volume Up/Down)
increases/decreases sound level.
GUIDE MUTE FAVOURITE
PR +/- (Programme Up/Down)
shows a programme schedule. VOL PR selects a programme.
(In Digital mode only) switches the set on from standby.
FAVOURITE
INFO LIST
INFO selects a favourite programme.
GUIDE PIP
displays information on top of the
screen during watching the TV. LIST
(In Digital mode only) displays the programme table.
MENU PIP
selects a menu. switches the sub picture on or off.
OK PIP PR +/-
selects a programme for the sub pic-
OK ture.
accepts your selection or displays SWAP
the current mode. alternates between main and sub
MENU EXIT picture.
D / E or F / G
adjusts menu settings. PSM SSM PIP INPUT
selects menu item. selects the input mode for the sub
picture.
PLAY PAUSE STOP RECORD
PSM (Picture Status Memory)
recalls your preferred picture setting. EXIT
REW FF SKIP
clears all on-screen displays and
returns to TV viewing from any
menu.
VCR BUTTONS PIP PR- PIP PR+ SWAP PIP INPUT SSM (Sound Status Memory)
controls a LG video cassette recalls your preferred sound setting.
recorder. UPDATE SIZE STILL I/II
TIME REVEAL ? MIX INDEX DVD BUTTONS

controls a LG DVD player.
I/II
selects the sound output or the audio
mode.
-4 -

Location and Function of Controls
<Front Panel Controls>
Remote Control Sensor
Power Standby Indicator

Illuminates red in standby
mode, Illuminates green
when the set is turned on
ON/OFF TV/AV MENU VOL PR
TV/AV Button
selects the TV, AV, Component,
RGB or DVI modes. If OSD is dis-
played, selects menu item.
Main Power Button switches the set on from standby.
MENU
displays on screen menus one by one.
exits the current menu.
memorizes menu changes.
D / E (Programme Up/Down)
selects a programme or a menu item.
switches the set on from standby.
F / G (Volume Up/Down)
adjusts the volume.
adjusts menu settings.
-5 -

Location and Function of Controls
<Back Panel>
S-VIDEO
VIDEO
A/V INPUT 2
9
R AUDIO L/MONO
DIGITAL AUDIO (OPTICAL) MONITOR
COMPONENT 2 DVD
. OUTPUT
DTV
A/V
COMPONENT 1 INPUT INPUT 1
Antenna
UPGRADE REMOTE DVI COMPONENT 1 DVI INPUT RGB INPUT R L ANALOG/DTV AC INPUT
OUTPUT AUDIO INPUT R AUDIO L VIDEO S-VIDEO
PORT CONTROL INPUT INPUT (PC/DTV) (PC/DTV)
AUDIO INPUT VIDEO INPUT
1 2 3 4 5 6 7 8
1. UPGRADE PORT 6. AUDIO/VIDEO IN SOCKETS (A/V INPUT 1)

This port is used to upgrade the software version and debug Connect the audio/video out sockets of external equipment to
without changing the hardware. these sockets.
Be careful not to use this port. Just contact your dealer or ser- S-VIDEO/AUDIO IN SOCKETS
vice centre. Connect the S-VIDEO out socket of the VCR to the S-VIDEO
socket.
2. CONTROL LOCK / REMOTE CONTROL Connect the audio out sockets of the VCR to the audio sock-
ets as in A/V INPUT 1.
3. DVI INPUT/COMPONENT 1 INPUT/OUTPUT (DIGITAL
AUDIO (OPTICAL)) 7. ANTENNA INPUT
Connect digital audio from various types of equipment.
Note: In standby mode, these ports will not work. 8. POWER CORD SOCKET
This Monitor operates on an AC power. The voltage is indi-
4. DVI INPUT / AUDIO INPUT / RGB INPUT (PC/DTV) cated on the Specifications page. Never attempt to operate
Connect the monitor output socket of the PERSONAL COM- the Monitor on DC power.
PUTER to this socket.
Note: If you want to use RGB/DVI audio, we strongly recom- 9. AUDIO/VIDEO IN SOCKETS (A/V INPUT 2)
mend that you use the cable that has a core, or the EMI Filter S-VIDEO/AUDIO IN SOCKETS
core along with separate cable.
5. COMPONENT INPUT
Connect DVD video outputs to Y, PB, PR of COMPONENT
INPUT and audio outputs to Audio sockets of AUDIO INPUT.
-6 -

Accessories
TV
VCR
DVD
CABLE
STB
AUDIO
MODE POWER
TV/AV
IA ARC MUTE
MULTIMED
1 2 3
4 5 6
7 8 9
FAVOURITE Q.VIEW
0
PSM SSM
VOL PR
PIP/DW TEXT/
MENU EXIT
OK
PIP PR- PIP INPUT

PIP PR+ SWAP
PLAY PAUSE STOP RECORD
LG TV
1.5V REW FF SKIP
1.5V
REVEAL WIN.SIZE WIN.POSITION SLEEP
?
AS mark I/II
SPLIT ZOOM LIST
Owner’s Manual Alkaline batteries Remote Control handset
2-TV bracket bolts

(or DT-50PY10 series: 4-TV 2-TV brackets 6-RING SPACER
Power Cord bracket bolts)
(Only DT-60PY10 series : 6-Wall 2-Wall brackets (option) (Only DT-60PY10 series)
mounting bracket bolts)
Joinning the TV assembly to the wall to protect the set tumbling

- Secure the TV assembly by joinning it to a wall by using the TV/Wall brackets.
• After the set must be mounted on s desk top, install the TV brackets on the TV as shown.
Insert the 2 bolts and tighten securely, in the holes on the bracket.
(Only DT-50PY10 series: After removing the existing bolts, insert the 4 bolts and tighten secure-
ly, in the holes on the bracket.)
Install the wall brackets on the wall with 4 bolts, (not supplied with the product), as shown.
Match the height of the TV brackets and the wall brackets.
Check to be sure the brackets are tightened securely.
• Secure the TV assembly to the wall with strong strings or wound wire cables, (not supplied
with the product), as shown.
Optional Extras
- Optional extras can be changed or modified for quality improvement without any notification new optional extras can be
added.
- Contract your dealer for buying these items.
50 42 40 40 42 50
42
40
40
42
50
Tilt wall mounting bracket Wall mounting bracket Tilt wall mounting bracket
(Only DT-60PY10 series) (Only DT-60PY10 series)
Ceiling mounting bracket
Ceiling mounting bracket Video cables Audio cables
-7 -

SPECIFICATIONS
NOTE : Specifications and others are subject to change without notice for improvement.
V Application Range V Test and Inspection Method
This spec is applied to the 42”, 50”, 60”PDP TV used AF-046A 1) Performance : LGE TV test method followed.
Chassis. 2) Demanded other specification
Safety: CB specification
EMC : CISPR 13 specification
V Specification
Each part is tested as below without special appointment. Model Name Market Remark
1) Temperature : 25¡ 5°C (77±9°F) DT-42PY10X Australia Safety : IEC60065, EN60065
2) Relative Humidity: 65¡ 10%
3) Power Voltage: Standard Input voltage (100-240V~, 50/60Hz) DT-50PY10 EMC : CISPR13 Class B
* Standard Voltage of each product is marked by models. DT-60PY10
4) Specification and performance of each parts are followed
each drawing and specification by part number in accordance
with BOM.
5) The receiver must be operated for about 20 minutes prior to the
adjustment.
V General Specification
Specification
No Item Remark
MIN Typ Max Unit
1 Broadcasting system PAL-B/G, DTV : DVB-T

2 Available Channel VHF : 00~12
UHF : 28~69
CATV : 02~44
3 Tuner IF PAL : 38.90MHz
DVB-T : 36.167MHz
4 Input Voltage 240V~, 50Hz Maker : SONY(42 inch)
SONY/Sanken(50 inch)
LG(60 inch)
5 PDP Module PDP42X2xxxx
PDP50X2xxxx RGB Closed Type
PDP60X5xxxx
6 Aspect ratio 16:9
7 Screen Filter 45% Total light transmittance(E-Mesh) Maker : LG Chemical
8 Operating Temperature 0 40 deg
9 Operating Humidity 85 %
10 Storage Temperature -20 60 deg
11 Storage Humidity 85 %
-8 -

ADJUSTMENT INSTRUCTIONS
1. Application Object
These instructions are applied to all of the PDP TV, AF-046A. Each PCB Assy must be checked by Check JIG Set before
assembly. (Especially, be careful Power PCB Assy which can
cause Damage to the PDP Module.)
2. Notes
(1) Because this is not a hot chassis, it is not necessary to use 4. POWER PCB Assy Voltage
an isolation transformer. However, the use of isolation
transformer will help protect test equipment. Adjustment (Va, Vs Voltage Adjustment)
(2) Adjustments must be done in the correct order.
(3) The adjustments must be performed in the circumstance of 4-1. Test Equipment : D.M.M 1EA
25±5°C of temperature and 65±10% of relative humidity if
there is no specific designation. 4-2. Connection Diagram for Measuring
(4) The input voltage of the receiver be must kept 220V, 60Hz Refer to Fig 1.
when adjusting.
Va
(5) The receiver must be operational for about 15 minutes P806
GND
prior to the adjustments. NC
VS P805 Vs ADJ
V401
DMM
O
Va ADJ
After receiving 100% white pattern, the receiver must be + - P804
RV601
operate prior to adjustment.(Or white condition in HEAT-

RUN mode)
O Enter into HEAT-RUN MODE
- Press the POWER ON KEY on R/C for adjustment.
OSD display and screen display 100% full WHITE P807
PATTERN.
P801 P802 P803
[ Set is activated HEAT-RUN without signal generator in <3501V00182B>
this mode. Va
P806
GND
NC
If you turn on a still screen more than 20 minutes (Especially VS P805 Vs ADJ
Digital pattern(13 CH), Cross Hatch Pattern), an afterimage DMM Va ADJ

V401
RV601
may occur in the black level part of the screen. + - P804
3. EPLD Download P807
P801 P802 P803
<3501V00188A>
PC
VSC <Fig. 2> Connection Diagram of Power Adjustment for
B/D Measuring (Power Board)
(1) Va Adjustment
<Fig 1> Connection Diagram of EPLD Download 1) After receiving 100% Full White Pattern, Heat-Run(over
10min).
(1) Test Equipment: PC, Jig for download 2) Connect + terminal of D.M.M to Va pin of P805 and
(2) Connect the power of VSC B/D. connect – terminal to GND pin of P805.
(3) Execute download program of PC. 3) Adjust RV601 voltage to match that of the label on the
(4) After executing the hot key on the Programmer, click icon Top/Right of the panel. (Deviation : ±0.5V)
(5) End after confirming.
(2) Vs Adjustment
1) Connect + terminal of D.M.M to Vs pin of P805 and
connect – terminal to GND pin of P805.
2) Adjust RV401 voltage to match that of the label on the
Top/Right of the panel. (Deviation : ±0.5V)
-9 -

5. EDID(The Extended Display
Identification Data)/DDC
(Display Data Channel) download
This is the function that enables “Plug and Play".
5-1. Required Test Equipment

1) PC, Jig for adjusting DDC (PC serial to D-sub. <Fig. 3> Adjustment Pattern : 720P 60Hz Color Bar Pattern
Connection equipment)
2) D-Sub to DVI Connector
6-3. Adjustment
5-2. Composition of Device (1) Input the color Bar Pattern of the 720P 60Hz Mode in the
Component INPUT and the select the Input Mode as
Component2.
(2) After receiving signal for at least 1 second, press the ADJ
PDP Key on the Service R/C to enter the ‘Ez - Adjust’ and select
SET the ‘1. AD9883A-Set’.
Pressing the Vol + Key to adjust with automatic movement.
(3) When the adjustment is over, 'Adjustment completed
(Press OK)' is displayed. If the adjustment has errors,
'AD9883A-Failed! Try Again' is displayed.
5-3. EDID DATA (4) Readjust after confirming the case Pattern or adjustment
condition where the adjustment errors.
- Download only EDID for DVI. (5) After adjustment is complete, exit the adjustment mode by
pressing the ADJ KEY.
00 01 02 03 04 05 06 07 08 09 0A 0B 0C 0D 0E 0F
00 | 00 FF FF FF FF FF FF 00 1E 6D 01 01 01 01 01 01
10 | 23 0E 01 03 80 6E 3E 78 0A 31 30 A5 58 3B B8 26
20 | 0F 4B 52 2F CE 00 31 CA 01 01 01 01 01 01 01 01
7. Adjustment of White Balance
30 | 01 01 01 01 01 01 C3 1E 00 20 41 00 20 30 10 60
40 | 13 00 4C 6C 42 00 00 18 00 00 00 FD 00 37 4E 1E
7-1. Required Equipment
(1) Color analyzer (CA-100 or similar product)
50 | 3E 08 00 00 00 00 00 00 00 00 00 00 00 FC 00 4C
60 | 47 20 54 56 0A 20 20 20 20 20 20 20 00 00 00 01 (2) Automatic adjustor (with automatic adjustment hour
70 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01 17 necessity and the RS-232C communication being possible)
80 | 02 01 04 00 01 1D 00 72 51 D0 1E 20 6E 28 55 00 (3) AV Pattern Generator
90 | C4 8E 21 00 00 1E 8C 0A D0 8A 20 E0 2D 10 10 3E
A0 | 96 00 C4 8E 21 00 00 18 01 1D 80 18 71 1C 16 20 7-2. Connection Diagram of Equipment
B0 | 58 2C 25 00 C4 8E 21 00 00 9E 00 00 00 00 00 00 for Measuring (Automatic Adjustment)
C0 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
D0 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 COLOR
E0 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ANALYZER
F0 | 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 BF TYPE; CA-100
CVBS Part
216 FULL WHITE PDP MONITOR
6. AD9883A-Set Adjustment
6-1. Synopsis
MSPG-2100 or
AD9883A-Set adjustment to set the black level and the Gain MSTG-5200
of optimum with an automatic movement from the analog =>
digital converter.
<Fig. 4> Connection Diagram of Automatic Adjustment
6-2. Test Equipment
Service R/C, 801GF(802B, 802F, 802R) or MSPG3240A
Pattern Generator
(720P 60Hz 100% Color Bar Pattern output will be possible
and the output level will accurately have to be revised with
0.7±0.1Vp-p)
- 10 -

[. RS-232C Command (Automatic Adjustment)
RS-232C Command CENTER

MIN MAX
[CMD ID DATA] (DEFAULT)
R Gain ja 00 XX 00 7f ff
G Gain jb 00 XX 00 7f(Fix.) ff
B Gain jc 00 XX 00 7f ff
R Cut lj 00 XX 00 3f(Fix.) 7f
G Cut lk 00 XX 00 3f 7f
B Cut ll 00 XX 00 3f 7f
7-3. Adjustment of White Balance(manual)

O Operate the Zero-calibration of the CA-100, then attach
sensor to PDP module surface when you adjust.
O Manual adjustment is also possible by the following sequence.
(1) Enter ‘3.White-Pattern’ by pressing ADJ KEY on the

Service Remote Control.
(2) Select "Test Pattern White" using Vol +/- Key and HEAT
RUN at least 15 minutes by pressing the ENTER Key.
(3) Receive the AV 50Hz, Full size, 216 Gray window pattern
signal from AV Pattern Generator.
Input mode : DT-42PY10X : AV2
DT-50PY10 : AV1
DT-60PY10 : AV1
(4) Select the Screen Adjustment as ‘Dynamic’.
(5) After attaching sensor to center of screen, select ‘2. White-
Balance’ of ‘Ez - Adjust’ by pressing the ADJ KEY on the
Service R/C. Then enter adjustment mode by pressing the
Right KEY (G) .
(6) Adjust the High Light using R Gain/B Gain.
(7) Adjust using Volume +/- KEY.(G Gain: 127)
DT-42PY10X : R Offset : 50/ B Offset : 48/ B Offset: 50

DT-50PY10 : R Offset : 52/ B Offset : 45/ B Offset: 60
DT-60PY10 : R Offset : 55/ B Offset : 50/ B Offset: 55
X; 0.290±0.003
Y; 0.290±0.003
Color temperature: 9,000°K±500°K
(7) After adjustment is complete, move to Ez - Adjust screen

by pressing the ENTER(Y) KEY. Then exit the adjustment
mode by press ADJ KEY.
- 11 -

TROUBLE SHOOTING GUIDE
1. Power Board
1-1. The whole flowchart which it follows in voltage output state
Start check
Doesn't the Yes It is identical No Is the Interface

screen whole come with Power Off signal operated?
out? condition?
Yes Yes
No 1. Check the Power Off 2. Check the Interface

condition. signal condition.
Doesn't the Yes Doesn't the No Doesn't the No Doesn't the

low pressure output St-by 5V signal 5V Monitor signal VSC signal RL-ON
come out? come out? come out? come out?
Yes Yes Yes
No 3. Check the St-by 5V 4. Check the 5V Monitor 5. Check the VSC RL-ON
signal circuit. signal circuit. signal.
Doesn't the Yes Doesn't the No Doesn't the Doesn't the

high tension output VSC signal Vs-ON Vs, Va voltage output VSC low pressure No
come out? come out? come out? output come out?
Yes Yes Yes
No 7. Check the VSC Vs-ON 8. Check the Vs, Va 6. Check the VSC low
signal voltage output circuit. pressure output
When remove When When

the Y, Z B/D Module remove the remove the
High tension Yes No No
Input Connector, Power Y B/D Module Z B/D Module
output voltage Drop
Board high tension output Input Connector, output Input Connector, output
it occurs?
voltage Drop voltage Drop voltage Drop
it occurs? it occurs? it occurs?
No
Yes Yes Yes
9. Check the Power 10. Check the Z B/D 11. Check the Y B/D
Manufacture enterprise Board Output high Module Coutput circuit Module Coutput circuit
meaning of a passage tension circuit
- 12 -

1-2. DT-42PY10X Sony Power Board Structure
T502: Vs Trans
T702: Va Trans
T101: St-by Trans
1 2 3
T103: Low Voltage Trans
- 13 -

1-3. DT-50PY10 Sony Power Board Structure
T502 : Vs Trans
T702 : Va Trans
T101 : St-by Trans
1 2 3
T103 : Low Voltage Trans
- 14 -

1-3. DT-50PY10 Sanken Power Board Structure
T221 : Vs Trans
T271 : Va Trans
T121 : St-by Trans
1 2 3
T201 : Low Voltage Trans
- 15 -

1-4. DT-60PY10 Power Board Structure
AC-IN
1 2 3
- 16 -

PFC
1 2 3
- 17 -

DC-DC
1 2 3
- 18 -

2. No Power
(1) Symptom
¯ Does’t minute discharge at module.
¯ Non does not come in into the front LED.
(2) Check follow
No
Is plug in power cord? Plug in power cord.
Yes
Is connected the Line Filter and No

Connect the Cable.
Power Switch Cable?
Yes
Is connected the Power Switch and No

Connect the Cable.
Power Board Cable?
Yes
Is normal the Fuse(F101) on Power No

Replace the Fuse.
Board?
Yes
Is connected the Power Board and No

Connect the Cable.
7P of VSC Board Cable?
Yes
Is connected the Power Switch and No

Connect the Cable.
Power Board Cable?
Yes
After remove the cable connection

to Power Board(except the CN101
connection cable), authorizes the
AC voltage marking on manual.
When ST-BY 5V does not operate,
replace the Power Board.
- 19 -

3. Protect Mode
(1) Symptom
¯ After once shining, it does not discharge minutely
from module
¯ The Rely falls(The sound is audible “click”)
¯ It is converted with the color where the front LED
is red from green.
(2) Check follow
No No
Is normal the Power Is output the normality Low/High Replace Power
Board? voltage except Stand-by 5V? Board.
Yes
Is normal the each No After connecting well each connector, No Replace

connector? the normality it operates? connector.
Yes
Is normal the output
No Yes Yes Replace
Is normal the Is normal the Fuse(FS2) on Y-B/D? voltage after remove
Y- Board? (in case of open is replace) (P3, P4) connector Y-Board.
of Y-B/D?
Yes
No Yes Replace
Is normal the Is normal the output voltage after
Z- Board? remove P12 connector of Z-B/D? Z-Board.
Yes
After remove P1, P2, P3, P4 output voltage
No Is normal the output voltage after Yes
Is normal the normality: Replace Right X-B/D
remove P1, 2, 3, 4, 5 connector of
X- Board? After remove P6, P7 output voltage
X-B/D?
normality: Replace Left X-B/D
Yes

Is normal the Replace
remove P101~P106 connector of
Ctrl Board? X-Board.
Ctrl-B/D?
Yes
After remove P1000 normal operation:
No Yes
Is normal the Is normal the output voltage after Replace Analog Board
VSC Board? remove P1000, P1200? After remove P1200 normal operation:
Replace Digital Board
Yes
No After crisis COF of each board, check the normality operates.

Is normal the
COF of X, Y, Z? If in case the normality operates, correspondence COF Fail is
replace the module.
1) Is normal the output Voltage after remove P1 -> Replace X Left-Bottom B/D
2) Is normal the output Voltage after remove P5-> Replace X Left-TOP B/D
3) Is normal the output Voltage after remove P100-> Replace X Center-TOP B/D
4) Is normal the output Voltage after remove P2-> Replace X Center-Bottom B/D
5) Is normal the output Voltage after remove P4-> Replace X Right-TOP B/D
6) Is normal the output Voltage after remove P3 -> Replace X Right-Bottom B/D
- 20 -

4. No Raster
(1) Symptom
¯ Does’t minute discharge at module.
¯ It maintains the condition where the front LED is green.
(2) Check follow
No No
Is normal the Power Is output the normality Low/High Replace Power
Board? voltage except Stand-by 5V? Board.
Yes
No No
Is normal the each After connecting well each connector, Replace
connector? the normality it operates? connector.
Yes
Is normal the output
No Yes Yes Replace
Is normal the Is normal the Fuse(FS2) on Y-B/D? voltage after remove
Y- Board? (in case of open is replace) (P3, P4) connector Y-Board.
of Y-B/D?
Yes
No Yes Replace
Is normal the Is normal the output voltage after
Z- Board? remove P1 connector of Z-B/D? Z-Board.
Yes
After remove P1, P2, P3, P4 output voltage
Is normal the normality: Replace Right X-B/D
remove P1, 2, 3, 4, 5 connector of X-
X- Board? After remove P6, P7 output voltage
B/D?
normality: Replace Left X-B/D
Yes

Is normal the Replace
remove P101~106 connector of Ctrl-
Ctrl Board? X-Board.
B/D?
Yes
After remove P1000 normal operation:
No Yes
Is normal the Is normal the output voltage after Replace Analog Board
VSC Board? remove P1000, P1200? After remove P1200 normal operation:
Replace Digital Board
Yes
No After crisis COF of each board, check the normality operates.

Is normal the
COF of X, Y, Z? If in case normality operates, correspondence COF Fail is
replace the module.
1) Is normal the output Voltage after remove P1 -> Replace X Left-Bottom B/D
2) Is normal the output Voltage after remove P5-> Replace X Left-TOP B/D
3) Is normal the output Voltage after remove P100-> Replace X Center-TOP B/D
4) Is normal the output Voltage after remove P2-> Replace X Center-Bottom B/D
5) Is normal the output Voltage after remove P4-> Replace X Right-TOP B/D
6) Is normal the output Voltage after remove P3 -> Replace X Right-Bottom B/D
- 21 -

5. In case of occur strange screen into specific mode
5-1. In case of does’t display the OSD
(1) Symptom
¯ LED is green
¯ The minute discharge continuously becomes
accomplished from module
(2) Check follow
Is normal the LVDS No Is connected the LVDS Yes

Replace the cable.
cable? cable correctly?
No
Connect the cable correctly.

Yes
Is normal the VSC No Operates the Thine Yes Operates the Yes Operates the Yes Replace the VSC
Digital Board? IC(IC1401)? IEP(IC1301)? Scaler(IC701)? Digital B/D
No No No
Replace Thine Replace the Replace the

Yes IC(IC1401). IEP(IC1301). Scaler(IC700).
Is normal the Ctrl No

Replace Ctrl B/D.
Board of Module?
- 22 -

5-2. In case of does’t display the screen into specific mode
(1) Symptom
¯ The screen does not become the display from specific input mode
(2) Check follow

¯ Check the all input mode should become normality display.
¯ Check the Video(Main)/Data(Sub), Video(Main)/Video(Sub) should become
normality display from the PIP mode or DW mode. (Re-Check it Swap)
(3) In case of becomes unusual display from RF mode
No Is connected the Tuner Yes Is normal the Input voltage, IIC

Is normal the Tuner?
Cable correctly? Communication and CVBS output?
No No
Yes
Connect the Cable correctly Replace the Tuner
No Is normal the Input voltage, IIC No

Is normal the
Replace the IC
CXA2069Q(IC301)? Communication and HV sync?
Yes
Is normal the VPC3230 No Is normal the Input voltage, IIC No

Replace the IC
or VPX3226? Communication and HV sync?
(4) in case of becomes unusual display from RF, AV mode

Is normal the
Replace the IC
CXA2069Q? Communication and HV sync?
Yes
Is normal the VPC3230 No Is normal the Input voltage, IIC No

Replace the IC
or VPX3226? Communication and HV sync?
- 23 -

(5) in case of becomes unusual display from Component, RGB-DTV/PC mode

Is normal the
Replace the IC
CXA2181Q(IC401)? Communication and HV sync?
Yes
Is normal the No Is normal the Input voltage, IIC No

Replace the IC
AD9883(IC501)? Communication and HV sync?
Yes

Is normal the Scaler? Replace the IC
Communication and HV sync?
(6) in case of becomes unusual display from DVI-DTV mode

Is normal the
Replace the IC
Sil169(IC601)? Communication and HV sync?
Yes

Is normal the Scaler? Replace the IC
(7) in case of becomes unusual display from DTV-PC mode
No Input the correct EDID in the

Is correct the EDID?
EEPROM(IC102)
Yes
Is the latest version the Graphic No Update the Graphic card driver
card driver of the PC? with the latest version
Yes

Is normal the Scaler? Replace IC
- 24 -

6. In case of no sound
(1) Symptom
¯ LED is green
¯ Screen display but sound is not output
(2) Check follow
No Yes
Is normal the SPK Is connected the SPK
Replace the SPK
cable? cable correctly?
No
Yes
Connect the Cable correctly
Is connected the Flat No Connect the Cable

cable correctly correctly.
Yes
No Yes Yes Yes

Is normal the Is normal the Is normal the Is normal the Is normal the
RF(Digital) sound? MSP4410K(IC501)? NSP6241(IC502)? TAS5122(IC503)? Scaler(IC503)?
No No No No
Replace the IC501 Replace the IC502 Replace the IC503 Replace the IC701
Yes
Yes
Is normal the Replace VSC

Is normal the No No
CS5330A(IC1205), Digital B/D
RF(Analog)/ AV/ Replace the IC
MC33078(IC1206),
Component L-R sound?
Scaler(IC701)?
Yes
Is normal the
No 74LCX157(IC1203), No
Is normal the SPDIF
sound? CS8415A(IC1202), Replace the IC
74LCS244(IC1201)
Scaler(IC701)?
- 25 -

BLOCK DIAGRAM
- 26 -

MEMO
- 27 -

EXPLODED VIEW
308 309
122
307 121
120
315 311
312 123
310
301
313
551
316 303
550
302
314
304
306
201
305 212
205 200
570
203
209
202
210 211
124
208
206
580
540 207
102
590 101
530
541
501
520 215
560 214
103
400
401
430
- 28 -

EXPLODED VIEW PARTS LIST
No. Part No. Descriptions

101 5900V12003B FAN,DC D12025S SDS 120MM*120MM*25MM 12V/0.2A 1300 5V-13.2V RPM
102 4980V01018A SUPPORTER, FAN EGI LEFT PDP DN-50PY10
103 4980V01017A SUPPORTER, FAN EGI RIGHT PDP DN-50PY10
120 6400WTTX01A SPEAKER,WOOFER N21C-6539-27C 16 OHM 10/15W 78DB OTHERS 56MM*56MM
121 6400TTTX01A SPEAKER,TWEETER N08D-6560 8 OHM 10/15W 77DB OTHERS 29MM*29MM
122 3110V00351A CASE, FRONT (R)SPEAKER DN-50PY10 ABS PDP
123 3550V00396A COVER, DUCT DN-50PY10 ABS PDP
124 3110V00352A CASE, FRONT (L)SPEAKER DN-50PY10 ABS PDP
200 6348Q-C036H PDP, 16:9 1365*768 PDP50X20562.AKLGG
201 6871QRH041C PWB(PCB) ASSEMBLY,DISPLAY XRRT ASSY HAND INSERT 50X2A COF RESISTOR
202 6871QCH045A PWB(PCB) ASSEMBLY,DISPLAY CTRL ASSY HAND INSERT 4023 50X2 FOR CI
203 6871QZH036B PWB(PCB) ASSEMBLY,DISPLAY ZSUS ASSY HAND INSERT 50X2A 4LAYER
205 6871QLH035C PWB(PCB) ASSEMBLY,DISPLAY XRLT ASSY HAND INSERT 50X2A COF RESISTOR
206 6871QXH025C PWB(PCB) ASSEMBLY,DISPLAY XRCB ASSY HAND INSERT 50X2A COF RESISTOR
207 6871QLH036C PWB(PCB) ASSEMBLY,DISPLAY XRLB ASSY HAND INSERT 50X2A COF RESISTOR
208 6871QDH081A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 50X2A YDRV_BTM
209 6871QYH032B PWB(PCB) ASSEMBLY,DISPLAY YSUS ASSY HAND INSERT 50X2A YSUS 4LAYER
210 6871QDH080A PWB(PCB) ASSEMBLY,DISPLAY YDRV ASSY HAND INSERT 50X2A YDRV_TOP
211 6871QRH042C PWB(PCB) ASSEMBLY,DISPLAY XRRB ASSY HAND INSERT 50X2A COF RESISTOR
212 6871QXH024C PWB(PCB) ASSEMBLY,DISPLAY XRCT ASSY HAND INSERT 50X2A COF RESISTOR
214 4980V00A53A SUPPORTER, ASSY NON RIGHT MODULE ASSY DN-50PY10
215 4980V00B46B SUPPORTER, MODULE AL RZ/RT/RP W/OUT PWR SUPP.
300 3091V00635A CABINET ASSEMBLY, DN-50PY10 STEREO E_PHONE AB00EA CABINET ASSY
302 4980V01073B SUPPORTER, ASSY AL FOR 50PY10 PRESS
303 4980V01076C SUPPORTER, FILTER EGI ASSY PRESS LEFT
304 4980V01074B SUPPORTER, ASSY AL FOR 50PY10 PRESS
305 5230V00020C FILTER(MECH), DU-50PY10 LG-CHEMICAL FLATRON PLASMA DELETE LG FOR AMREICA
306 4980V01075C SUPPORTER, FILTER EGI ASSY PRESS RIGHT
307 3210V00241A FRAME, FRONT UPPER AL DN-50PY10 PDP
308 4972V00106A FIXER, FRAME AL DN-50PY10 PDP
309 4811V00090A BRACKET ASSEMBLY, SPEAKER DN-50PY10 L(4810V00947) AB00EA .
310 3210V00261A FRAME, FRONT SIDE AL DN-50PY10 FOR LEFT(NEW P/NO)
311 3790V00761F WINDOW, DECO DT-50PY10 (AUS) ACRYL GENERAL BK LEFT
312 3210V00243A FRAME, FRONT AL RIGHT, DN-50PY10 PDP
313 3790V00760G WINDOW, DECO DT-50PY10 ACRYL INDEX ASSY RIGHT
314 4811V00089A BRACKET ASSEMBLY, SPEAKER DN-50PY10 R(4810V00946) AB00EA .
315 4972V00105A FIXER, FRAME AL DN-50PY10 PDP
316 3210V00242C FRAME, BOTTOM AL RZ-50PY10 TV/AV MENU VOL PR
400 3809V00441G BACK COVER ASSEMBLY, DT-50PY10 W/L 411-960K
401 3300V00364B PLATE, AV AL COVER VSC TUNER
430 3501V00178B BOARD ASSEMBLY, ASSY AP-50DY11.AL AF044A FOR WITHOUT PACKING
501 3301V00018H PLATE ASSEMBLY, ASSY 3300V00319D+3301V00029G DT-50PY10 AUSTRALIA
520 6871VMMT40A PWB(PCB) ASSEMBLY,MAIN AF-046A AUS MAIN DIGITAL MANUAL
530 6871VSMS12A PWB(PCB) ASSEMBLY,SUB TUNER AF046A AUS SUB ANALOG MANUAL
540 6871VSME92A PWB(PCB) ASSEMBLY,SUB PSW RF043A MAILBU
541 5020V00948A BUTTON, POWER DN-50PZ10 ABS, AF-303S 1KEY PDP
550 6871VSMJ97A PWB(PCB) ASSEMBLY,SUB A/V AF046A DT-50PY10 SIDE A/V MANUAL
551 4811V00095E BRACKET ASSEMBLY, SIDE AV RT/RP-50PY10 RF043B BRACKET ASSY
560 6871VSMF11B PWB(PCB) ASSEMBLY,SUB CONT AF044A DN-42PY11X CONTROLLER B/D
570 6871VSMABOB PWB(PCB) ASSEMBLY,SUB LED AF046A DT-50PY10 INDEX ASSY
580 3501V00188A BOARD ASSEMBLY, POWER RU-50PX10 RF043A SONY APS210 PDP 50 PSU H/C
590 3141VSN930A CHASSIS ASSEMBLY, SUB AF044A AC INET
- 29 -

REPLACEMENT PARTS LIST
LOCA. NO PART NO DESCRIPTION LOCA. NO PART NO DESCRIPTION
IC702 0IMMRSS041D K4S641632H-TL75 54P TSOP
IC
IC703 0IMMRSS041D K4S641632H-TL75 54P TSOP
IC1001 0IMCRXL004A XC95288XL-10TQG144C XILINX 144P IC704 0IMMRSS041D K4S641632H-TL75 54P TSOP
IC1003 0ICTMLG013A LGDT1901A LG IC 24P SSOP IC705 0IMMRSS041D K4S641632H-TL75 54P TSOP
IC1004 0IMCRCY002A CY2309SC-1HT CYPRESS SOIC 16P IC801 0IMI372726A COPY M37272EFSP6(OTP) 42SDIP
IC101 0IMI623200B M62320FP,I/O EXPANDER 16P SOP TP IC802 0IKE704200J KIA7042AF SOT-89 TP 4.2V
IC101 0IMMRAL014B AT24C02N-10SI-2.7 ATMEL 8P SOIC IC803 0IMCRAL006A AT24C16AN-10SI-2.7 ATMEL 8P SOIC
IC102 0IMI623200B M62320FP,I/O EXPANDER 16P SOP TP IC901 0IMCRSS016A S3C44BOX01-EDRO LQFP-160
IC102 0IMMRAL014B AT24C02N-10SI-2.7 ATMEL 8P SOIC IC904 0IMMRSS041D K4S641632H-TL75 54P TSOP
IC103 0IMCRTI003A SN74HCT08D 16P R/TP QUADRUPLE IC905 0IMMRSS041D K4S641632H-TL75 54P TSOP
IC105 0IMCRFA015A KA7805R FAIRCHILD 2P D-PAK R/TP 500MA IC906 0IAL242561B AT24C256W-10SI-2.7V 8P SOIC ST
IC1101 0IMCRPH026A PCA9516PW PHILIPS 16P TSSOP
IC1102 0IMCRSG010A ST3232CDR SOP16 R/TP RS232
TRANSISTOR
IC1103 0IKE702900G KIA7029AF SOT-89 TP 2.9V Q101 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1104 0IPH741400E 74HC14D 14SOP TP SHITTER TRIGGER Q101 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1105 0IMCRPH026A PCA9516PW PHILIPS 16P TSSOP Q102 0TR150400BA CHIP 2SA1504S(ASY) KEC
IC1201 0IMCRFA013A 74LCX244MTC FAIRCHILD 20P TSSOP Q102 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1202 0ICB841500B CS8415A-CZR 28P TSSOP R/TP 96KHZ Q102 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1203 0ITO741570C TC74LCX157FT 16P,TSSOP TP Q103 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1204 0ITO741570C TC74LCX157FT 16P,TSSOP TP Q103 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1205 0ICB533100A CS5331A-KSR 8SOIC TP ADC Q103 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1206 0IMO330780B MC33078D 8/SOIC TP LINEAR +-18V OP AMP Q104 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1301 0ICTMLG018A LGDP4410 LG IC 176P TQFP Q104 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1401 0IMCRTH002A THC63LVD103 64P TQFP TRAY 10BIT LVDS TX Q105 0TR150400BA CHIP 2SA1504S(ASY) KEC
IC1501 0IDS162100B DS1621V 8P SOIC ST THERMOSTAT - Q105 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1502 0IPMGKE032A KIA78R09F KEC 5PIN DPAK Q106 0TR150400BA CHIP 2SA1504S(ASY) KEC
IC1503 0IPMGKE032A KIA78R09F KEC 5PIN DPAK Q106 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1602 0IMCRRH001A BA033FP-E2 ROHM 3P-SOP,TO252-3 Q107 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1603 0IMCRSJ001A SC1565IST-1.8 SEMTECH 3P SOT223 TP Q108 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1604 0IMCRFA010A KA7809R, FAIRCHILD 2P D-PAK Q109 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC1605 0IPRPML001A MIC39100 MICREL 3P SOT223 Q110 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC201 0IIT323000E VPC3230D C5 80P QFP Q111 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC301 0ILNRMN005A VPX3226E MICRONAS 44 QFP Q112 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC301 0ISO206900A CXA2069Q QFP64 BK I2C BUS AV S/W Q113 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC401 0IMCRMN023A SDA6001 QH B12 MICRONAS 128P MQFP Q114 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC401 0IMCRSO025A CXA2181Q SONY 48P QFP Q201 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC402 0IMMRHY001F HY57V641620HGT-H HYNIX 54P TSOPII Q201 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC403 0IMMRMR006B MX29LV160ATTC-70 MACRONIX 48P TSOP Q202 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC404 0IMCRAL006A AT24C16AN-10SI-2.7 ATMEL 8P SOIC Q202 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC405 0IKE702700D KIA7027AF 3, SOT-89 TP RESET IC 2.7V Q203 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC501 0IMCRAD002A AD9883AKST-110 80P TQFP Q203 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC501 0IMCRMN028B MSP4410K MICRONAS 80P/PQFP Q204 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC502 0IMCRNL001A NSP-6241B NEOFIDELITY 64P TQFP Q204 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC503 0IMCRTI028C TAS5122DCAR 56P/TSSOP R/TP 30W Q205 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC601 0IMCRS5003A SIL169CT100 SILICON IMAGE 100P LQFP Q205 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC601 0ITK118100B TK11840L 8P SOT23L R/TP DC-DC Q206 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC603 0IMCRFA010A KA7809R, FAIRCHILD 2P D-PAK Q301 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC604 0IPRPML001A MIC39100 MICREL 3P SOT223 Q302 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC606 0IMCRSJ001A SC1565IST-1.8 SEMTECH 3P SOT223 Q303 0TR387500AA CHIP 2SC3875S(ALY) KEC
IC701 0ICTMLG009A LGDT1102 HD2 LG IC SBGA-432PIN Q304 0TR387500AA CHIP 2SC3875S(ALY) KEC
- 30 -

For Capacitor & Resistors, CC, CX, CK, CN : Ceramic RD : Carbon Film
the charactors at 2nd and 3rd CQ : Polyestor RS : Metal Oxide Film
digit in the P/No. means as CE : Electrolytic RN : Metal Film
follows; RF : Fusible
Q305 0TR387500AA CHIP 2SC3875S(ALY) KEC

CAPACITOR
Q306 0TR387500AA CHIP 2SC3875S(ALY) KEC
Q401 0TR150400BA CHIP 2SA1504S(ASY) KEC C104 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP
Q401 0TR387500AA CHIP 2SC3875S(ALY) KEC C104 0CE476DF618 47UF STD 16V M FL TP5
Q402 0TR387500AA CHIP 2SC3875S(ALY) KEC C104 0CE476SF6DC 47UF MVG 16V M SMD R/TP
Q402 0TR387500AA CHIP 2SC3875S(ALY) KEC C105 0CE476DF618 47UF STD 16V M FL TP5
Q501 0TR102009AG CHIP KRC102S KEC TP SOT-23 NA NA C1110 0CE476SF6DC 47UF MVG 16V M SMD R/TP
Q502 0TR150400BA CHIP 2SA1504S(ASY) KEC C124 0CE476SF6DC 47UF MVG 16V M SMD R/TP
Q503 0TR150400BA CHIP 2SA1504S(ASY) KEC C125 0CE476SF6DC 47UF MVG 16V M SMD R/TP
Q504 0TR150400BA CHIP 2SA1504S(ASY) KEC C1267 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
Q505 0TR150400BA CHIP 2SA1504S(ASY) KEC C1268 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
Q506 0TR387500AA CHIP 2SC3875S(ALY) KEC C1269 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
Q508 0TR102008AA KRA102S R/TP KEC SOT23 CHIP TR C1271 0CE107SF6DC 100UF MVG 16V M SMD R/TP
Q601 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR C1272 0CE107SF6DC 100UF MVG 16V M SMD R/TP
Q601 0TRKE80038A KTC3552T-RTK KEC R/TP SOT-23F 50V 3A C1273 0CE107SF6DC 100UF MVG 16V M SMD R/TP
Q602 0TR830009BA BSS83 TP PHILIPS N-CHANNEL S/W TR C1274 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
Q901 0TR102008AA KRA102S R/TP KEC SOT23 CHIP TR C1276 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C1277 0CE476SF6DC 47UF MVG 16V M SMD R/TP
DIODE 470UF MVG 16V 20% R/TP(SMD) SMD
C1278 0CE477SF6DC
D101 0DD226239AA CHIP KDS226 SOT-23 C1279 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
D102 0DD226239AA CHIP KDS226 SOT-23 C1280 0CE476SF6DC 47UF MVG 16V M SMD R/TP
D104 0DD184009AA KDS184S CHIP 85V 300MA KEC TP C1282 0CE476SF6DC 47UF MVG 16V M SMD R/TP
D1101 0DD184009AA KDS184S CHIP 85V 300MA KEC TP C1283 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
D602 0DD184009AA KDS184S CHIP 85V 300MA KEC TP C1288 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
ZD101 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A C1293 0CE476SF6DC 47UF MVG 16V M SMD R/TP
ZD106 0DR050008AA SD05.TC R/TP SEMTECH SOD323 5V 5A 15A C1298 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
ZD501 0DZ820009AH MTZJ8.2B TP ROHM-K DO34 - 8.2V 5UA - C1303 0CE476SF6DC 47UF MVG 16V M SMD R/TP
- 31 -

C1305 0CE476SF6DC 47UF MVG 16V M SMD R/TP C414 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1307 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD C416 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1315 0CE105SK6DC 1UF MVG 50V M SMD R/TP C429 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1317 0CE227VF6DC 220UF MV 16V 20% R/TP(SMD) SMD C431 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD
C1319 0CE476SF6DC 47UF MVG 16V M SMD R/TP C432 0CE105SK6DC 1UF MVG 50V M SMD R/TP
C201 0CE476SF6DC 47UF MVG 16V M SMD R/TP C438 0CE476SF6DC 47UF MVG 16V M SMD R/TP
C203 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C507 0CE476SF6DC 47UF MVG 16V M SMD R/TP
C204 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C509 0CE335SK6DC 3.3UF MVG 50V 20% SMD R/TP
C205 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C511 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C206 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP C520 0CE335SK6DC 3.3UF MVG 50V 20% SMD R/TP
C207 0CE476SF6DC 47UF MVG 16V M SMD R/TP C531 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C212 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C556 0CK105DF64A 1UF 2012 16V 20% R/TP F(Y5V)
C213 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD C560 0CK105DF64A 1UF 2012 16V 20% R/TP F(Y5V)
C251 0CE476SF6DC 47UF MVG 16V M SMD R/TP C576 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP
C307 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP C583 0CE108DJ618 1000UF STD 35V M FL TP5
C308 0CE227VF6DC 220UF MV 16V 20% R/TP(SMD) SMD C597 0CE108DJ618 1000UF STD 35V M FL TP5
C309 0CE105SK6DC 1UF MVG 50V M SMD R/TP C602 0CE107SF6DC 100UF MVG 16V M SMD R/TP
C309 0CE476SF6DC 47UF MVG 16V M SMD R/TP C603 0CE107SF6DC 100UF MVG 16V M SMD R/TP
C309 0CK105DF64A 1UF 2012 16V 20% R/TP F(Y5V) C604 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C318 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP C607 0CE105SK6DC 1UF MVG 50V M SMD R/TP
C319 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP C609 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C325 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP C610 0CE227VF6DC 220UF MV 16V 20% R/TP(SMD) SMD
C327 0CK225DFK4A 2.2UF 2012 16V 20%,-20% F(Y5V) R/TP C611 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C328 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP C612 0CE477DJ618 470UF STD 35V 20% FL TP 5
C329 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP C613 0CE227VF6DC 220UF MV 16V 20% R/TP(SMD) SMD
C330 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP C614 0CE477DJ618 470UF STD 35V 20% FL TP 5
C331 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP C615 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C356 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP C616 0CE105SK6DC 1UF MVG 50V M SMD R/TP
C370 0CK823DK56A 82000PF 2012 50V 10% R/TP X7R C617 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
C388 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP C624 0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
- 32 -

C638 0CE107SF6DC 100UF MVG 16V M SMD R/TP JK101 6630VGA001C 68114-1521 MOLEX 15PIN 2.29MM ANGLE SN
C646 0CE107SF6DC 100UF MVG 16V M SMD R/TP JK103 6630GZ00724 67351-4006 MOLEX 24P 1.91MM DVI-D RIGHT ANGLE
C647 0CE107SF6DC 100UF MVG 16V M SMD R/TP P1102 6630VGA004B 69107-0921 MOLEX 9P 2.77MM FORK
0CE477SF6DC 470UF MVG 16V 20% R/TP(SMD) SMD
RESISTOR
C652
C653 0CE476SF6DC 47UF MVG 16V M SMD R/TP AR101 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P
C662 0CE227VF6DC 220UF MV 16V 20% R/TP(SMD) SMD AR1303 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P
C681 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP AR1401 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P
C686 0CE475SK6DC 4.7UF MVG 50V 20% SMD R/TP AR1405 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P
C728 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD AR602 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P
C827 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP AR606 0RRZVTA001D 22 OHM 1 / 16 W 1608 5% R/TP 4P
C902 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD AR901 0RRZVTA001C 4.7K OHM 1 / 16 W 1608 5% R/TP 4P
C903 0CE106SF6DC 10UF MVG 16V 20% R/TP(SMD) SMD AR902 0RRZVTA001C 4.7K OHM 1 / 16 W 1608 5% R/TP 4P
C909 0CE476SF6DC 47UF MVG 16V M SMD R/TP R1101 0RD0182H609 18 OHM 1/2 W 5.00% TA52
C918 0CE107SF6DC 100UF MVG 16V M SMD R/TP R1209 0RS0562H609 56 OHM 1/2 W 5.00% TA52
C919 0CE107SF6DC 100UF MVG 16V M SMD R/TP R1210 0RS0562H609 56 OHM 1/2 W 5.00% TA52
C920 0CE107SF6DC 100UF MVG 16V M SMD R/TP R310 0RN1002F409 10K OHM 1/6 W 1.00% TA52
C953 0CE107SF6DC 100UF MVG 16V M SMD R/TP R801 0RKZVTA001L 1.0M OHM 1/2 W 5% TA52
C954 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP R802 0RKZVTA001L 1.0M OHM 1/2 W 5% TA52
C955 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
LED
C973 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP
C974 0CE226SF6DC 22UF MVG 16V 20% SMD R/TP DL1601 0DL233309AC SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
DL1602 0DL233309AC SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
COIL
DL1603 0DL233309AC SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
L1601 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4 DL1604 0DL233309AC SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
L1603 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4 IC103 6301V00003A UEX-LD-048 WHITE WHITE LED INDEX
L1604 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4 IC104 6301V00003A UEX-LD-048 WHITE WHITE LED INDEX
L1623 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4 LD601 0DL233309AC SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
L506 6140VB0024A LPK-1322A SOOJUNG 22UH +-10% LD602 0DL233309AC SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
L509 6140VB0024A LPK-1322A SOOJUNG 22UH +-10% LED101 0DL233309AC SAM2333 GREEN/RED GREEN:10MCD, RED:6MCD
L601 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4
6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4
SWITCH
L602
L603 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4 SW1101 6600VR1004A SKHMPW 5P CHIP TACT J-ALPS
L604 6140VB0004B 26UH 1UEWPHY 22.5TURN YL-9N 0.4 SW201 140-315A TACT SKHV17910B LG C&D 12V
SW202 140-315A TACT SKHV17910B LG C&D 12V
SW203 140-315A TACT SKHV17910B LG C&D 12V
- 33 -

SW204 140-315A TACT SKHV17910B LG C&D 12V L1630 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
SW800 6600VM2006A SDDF3PATP011 250V 4A HORIZONTAL .G L1633 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
X1001 6600VR1004A SKHMPW 5P CHIP TACT J-ALPS L205 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
L206 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
FILTER & CRYSTAL L207 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
F201 6200C000010 H354LAI-K5202 R/TP RN-49NZ10HA L208 6210VC0005A BK2125 HS 750 2X1.25X0.85MM R/TP
F302 6200C000010 H354LAI-K5202 R/TP RN-49NZ10HA L211 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA
IC502 0IZZVF0022C AFM730F6M00X3(AF9397A) SIP 15P ST ACTIVE LPF L216 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA
L101 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP L217 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA
L102 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP L302 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
L106 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA L607 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
L107 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA L608 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP
L1616 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP R102 6200JB8010L MLB-201209-1000L-N2 R/TP 1000OHM 350MA
L1621 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP X201 6202VDB007B RESONATOR,CRYSTAL HC49U 20.250MHZ
L1622 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP X301 6202VDB007B RESONATOR,CRYSTAL HC49U 20.250MHZ
L1624 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP X401 6202VDT002K RESONATOR,CRYSTAL SX-1 SUNNY 6MHZ
L1625 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP X401 6212AB2015A RESONATOR,CRYSTAL HC-49/SM4H 4MHZ
L1626 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP X402 6212BA2002C RESONATOR,CRYSTAL CSALA2M69G4ZF01-B0
L1627 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP X501 156-A02M RESONATOR,CRYSTAL HC49U 18.432MHZ
L1628 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP X801 6202VDT002D RESONATOR,CRYSTAL SX-1SMD 8.0MHZ
L1629 6210VC0006A FBMH3216 HM501NT 3.2X1.6X1.6MM R/TP X901 6212AB2015E RESONATOR,CRYSTAL HC-49/SM 10.0MHZ
- 34 -

JACK
JK102 380-068E UEJ-CV-018 UGCOM D3.5 E/P
JK103 6613V00026A UJB-03-28A
JK1101 380-068E UEJ-CV-018 UGCOM D3.5 E/P
JK1201 6612BBBHN4A TOTX179 OPTIC TX MODULE JACK
JK1202 6612BBBHN4B TORX179 S/PDIF OPTICAL RX JACK
JK1203 6612BBBHN4B TORX179 S/PDIF OPTICAL RX JACK
JK201 6612VJH020C PPJ122C A/V 6P(COMPONENT)+SHIELD+GOLD
JK202 6612VJH020B PPJ122B A/V 6P+SHIELD+GOLD
JK203 6612VJH019B PPJ121B A/V 4P+SHIELD+GOLD
P201 380-363G 6046B-01S H=8.0 WITH S/W,SHIELD
ACCESSORIES
A1 3828VA0505A MANUAL,OWNERS, AF046A LG EN TX 026H
A2 6710V00116X REMOTE CONTROLLER, MB04EA PIP
A3 6410VSH001E POWER CORD, BP3110 SAA 2800MM
A4 4810V00509B BRACKET, WALL AP-60DA10
A5 6850J00005A CABLE,DVI LVDS UL20276 AWG30 500MM
A6 6850VA0004F CABLE,COAXIAL UL1365AWG26 200 MM
A7 6851V00022C CABLE,COAXIAL UL1365#26 VW-1
MISCELLANEOUS
F801 0FS1002B53K FUSE,SLOW BLOW 10000MA 250 V 5.2X20
TU101 6700MF0001J TUNER, TAUH-Z340D 4SYSTEM 2IN1 0001C
TU102 6700DF0001A TUNER, TDFB-Z205P OFDM DEMODULATOR
X1001 6204B60001B OSCILLATOR, VCXO BUBANG 27MHZ
- 35 -

PRINTED CIRCUIT BOARD
MAIN (TOP) MAIN (BOTTOM) POWER S/W(TOP) POWER S/W(BOTTOM) SIDE A/V (TOP)
SIDE A/V (BOTTOM)
CONTROL (TOP) CONTROL (BOTTOM)
INDEX (TOP)
INDEX (BOTTOM)
TUNER (TOP) TUNER (BOTTOM)

Nov., 2004
P/NO : 3828VD0193B Printed in Korea

DT 50 Py 10

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

DT 50 Py 10

Uploaded by

Copyright:

Available Formats

website:http://biz.LGservice.

Downloaded from www.Manualslib.com manuals search engine

SAFETY PRECAUTIONS ...................................................................................3

DESCRIPTION OF CONTROLS ........................................................................ 4

ADJUSTMENT INSTRUCTIONS ........................................................................9

TROUBLE SHOOTING GUIDE ..........................................................................12

BLOCK DIAGRAM .............................................................................................26

EXPLODED VIEW ..............................................................................................28

EXPLODED VIEW PARTS LIST ........................................................................29

REPLACEMENT PARTS LIST...........................................................................30

SCHEMATIC DIAGRAM ........................................................................................

PRINTED CIRCUIT BOARD ..................................................................................

Downloaded from www.Manualslib.com manuals search engine

IMPORTANT SAFETY NOTICE

General Guidance Leakage Current Hot Check (See below Figure)

Due to high vacuum and large surface area of picture tube,

Good Earth Ground

Downloaded from www.Manualslib.com manuals search engine

Remote Control Key Functions

displays the selected device. POWER

TIME REVEAL ? MIX INDEX DVD BUTTONS

Downloaded from www.Manualslib.com manuals search engine

<Front Panel Controls>

Remote Control Sensor

Power Standby Indicator

ON/OFF TV/AV MENU VOL PR

Downloaded from www.Manualslib.com manuals search engine

1. UPGRADE PORT 6. AUDIO/VIDEO IN SOCKETS (A/V INPUT 1)

Downloaded from www.Manualslib.com manuals search engine

PIP PR- PIP INPUT

PLAY PAUSE STOP RECORD

SPLIT ZOOM LIST

Owner’s Manual Alkaline batteries Remote Control handset

2-TV bracket bolts

Joinning the TV assembly to the wall to protect the set tumbling

Ceiling mounting bracket Video cables Audio cables

Downloaded from www.Manualslib.com manuals search engine

1 Broadcasting system PAL-B/G, DTV : DVB-T

Downloaded from www.Manualslib.com manuals search engine

operate prior to adjustment.(Or white condition in HEAT-

[ Set is activated HEAT-RUN without signal generator in <3501V00182B>

Digital pattern(13 CH), Cross Hatch Pattern), an afterimage DMM Va ADJ

3. EPLD Download P807

P801 P802 P803

Downloaded from www.Manualslib.com manuals search engine

5-1. Required Test Equipment

Downloaded from www.Manualslib.com manuals search engine

RS-232C Command CENTER

7-3. Adjustment of White Balance(manual)

(1) Enter ‘3.White-Pattern’ by pressing ADJ KEY on the

DT-42PY10X : R Offset : 50/ B Offset : 48/ B Offset: 50

Color temperature: 9,000°K±500°K

(7) After adjustment is complete, move to Ez - Adjust screen

Downloaded from www.Manualslib.com manuals search engine

Doesn't the Yes It is identical No Is the Interface

No 1. Check the Power Off 2. Check the Interface

Doesn't the Yes Doesn't the No Doesn't the No Doesn't the

Yes Yes Yes

Doesn't the Yes Doesn't the No Doesn't the Doesn't the

Yes Yes Yes

When remove When When

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine