TDX 5000

Tan Delta & Capacitance

Test System
 TDX 5000
2

Power Factor, Dissipation factor (Tan Delta) and

Capacitance Diagnostic System for Power Apparatus

• Fully automatic • PADS - Power Apparatus Diagnostic Software

for automatic testing, assessment and report
• Tan Delta, capacitance, dissipation factor
measurements and excitation current test • Tan Delta test for rotating machines
(generators and motors)
• Variable output frequency: 1 ÷ 500 Hz
• USB interface and Ethernet interface
• Output voltage: from 0 V up to 12 kV for PC connection

• Voltage sweep and frequency sweep (tip up or • Compact and lightweight

down tests)
• Patented technology for capacitance
• Local control with a large graphic display and Tan Delta measurement

RCTD
COMPENSATING
REACTOR

TDMS

CAP CAL
CALIBRATOR
MODULE

TDX 5000 CAPACITANCE

AND TAN DELTA TEST SYSTEM

STOIL CELL
 Power Factor & Capacitance Diagnostic System for Power Apparatus
3

Application
The following table lists the tests that can be performed on CTs,
VTs and PTs.

N. TEST TEST DESCRIPTION

10 CT Tan Delta measurements
16 VT Tan Delta measurements
20 PT No-load / excitation current
22 PT Tan Delta measurements
23 PT Ratio with RTD
25 CB Tan Delta measurements
30 Capacitor Measurement of the
capacitance Banks

Tests are performed in accordance with the following IEC standards:

IEC61869-2; IEC61869-3; EN 60044-1; EN 60044-2; EN 60044-5;
EN 60076-1, and also in accordance with C57,12-90.

General Characteristic System Description

TDX 5000 equipment performs the measurement of the Tan Delta, The STS family includes three models : STS 5000, STS 4000 and TDX
of the dissipation factor and of the capacitance of a transformer 5000. TDX 5000 is developed as a compact solution for high voltage
or of any MV and EHV device (13.8 kV up to more than 500 kV), at Capacitance and Tan Delta (Dissipation Factor) measurements on
the frequency of the mains or in a wide frequency range. With the CT, VT, PT, bushings. Using the reactor option, TDX 5000 can also
RTD option is possible to measure the transformer ratio with high perform tests on rotating machines (motors and generators).
voltage. The measurement is performed by patented technology. In the local control mode, the selected output is adjustable and
metered on the large, graphic LCD display. With the control knob
TDX 5000 measurement circuitry incorporates a reference high and the LCD display, it is possible to enter the MENU mode, that
voltage capacitor, rated 200 pF, with a Tan Delta better than allows to set many functions and that make TDX 5000 a very
0.005%, and a reference resistor bridge, with accuracy better than powerful testing device, with manual and automatic testing
0.01%, and thermal drift less than 1 ppM/°C. The patented circuitry capabilities and with the possibility to transfer test results to a
and the variable frequency output make test results immune from PC via ETHERNET or Pen Drive. The TDMS software suite, which
external noise. comes with the test set, allows to download, display and analyse
Before each test, the TDX5000 automatic check and calibrate itself test results obtained in local mode. Remote maintenance and
with the internal reference capacitor. diagnostic of the instrument is available via Ethernet. TDMS
Available test selections: operates with all Windows® versions.
• Ungrounded: UST-A; UST-B; UST A+B The ease of operation has been the first goal of TDX 5000 unit. This
• Grounded: GST; GSTg-A; GSTg-B; GSTg-A+B. is why the LCD display is so large and the dialogue in MENU mode
TDX 5000 is powered by an internal voltage generator with is made easy.
electronic control. The instrument must be grounded during the TDX 5000 includes the detection of the digital signal coming from
operation, in case the ground is disconnected during the test, the the RTCD- Compensating Reactor option.
generation stops automatically. The instrument is housed in a transportable aluminium box, which
TDX5000 can be supplied with a portable generator without loss is provided with cover and handles for ease of transportation. A
of performances. transport trolley can be optionally supplied.

LEGENDA:

TDMS

POWER TRANSFORMER CIRCUIT BREAKER CURRENT AND VOLTAGE ELECTRIC MOTOR POWER GENERATOR
TESTING TESTING TRANSFORMER TESTING TESTING TESTING
 TDX 5000
4

TDMS - Test & Data Management Software

TDMS, Test & Data Management Software, is a powerful

software package providing data management for acceptance
and maintenance testing activities. Electrical apparatus data
and test results are shown in the local frontal interface and are
automatically saved in the TDMS database for historical results
analysis.
The TDMS database organizes test data and results for the
majority of electrical apparatus tested with ISA test sets and
related software. All the results include the information about
the apparatus under test, location, references, operator, data,
time, ambiental conditions and graphs. With TDMS software
is possible to export the data to electronic formats like XLSX
(EXCEL), CSV, DOC, RPT, PDF, JPEG y XML.

PADS - Power Apparatus Diagnostic Software

PADS - Power Apparatus Diagnostic Software is a powerful
software application, included in TDMS software, that optionally
allows the remote control of the STS family: STS 5000, STS 4000,
TDX 5000. The software performs various tasks, such as:
• Control TDX 5000 remotely from PC
• Create test plan
• Download stored test results via Ethernet cable
• Create and customize test reports
• Print test results
This program runs under Windows© environment.
Note: Windows is trademark of Microsoft Corporation.

TDX 5000 - Front Panel

Display Keyboard

Safety Key Digital

input

Function
keys

Power Multifunction Emergency

Start/Stop
ON/OFF function knob push-button
 Power Factor & Capacitance Diagnostic System for Power Apparatus
5

TDX 5000 - Side Panels

High voltage
output

TDX 5000 - Side Panels

Measuring External
inputs devices input
Ground Remote start UST-A
connection Power supply Safety warnings UST-B Interfaces
 TDX 5000
6

Test Header
Before starting a test, all relevant test object data are input into If the device is a PT, the Capacitance tests and the no-load /
the header, which is made of four screens. These data are used by excitation current test can be pre-set together, to form a single Test
the device for the following test execution. If, during tests, some Plan. The Test Plan can be saved and recalled; up to 64 different
results do not conform and nominal data are to be modifi ed, the plans can be stored into memory.
change is made in the Header, so that consistent nominal data
and the corresponding test results are saved together.

Nominal values window: from these nominal data, Tests header window: test reference data
the program computes the nominal saturation knee

Tolerances window allows setting the tolerances for Test selection window: it allows selecting the test to
each of the available tests be performed

At the end of the programming, starting the first test will execute the complete sequence.
During the test, test results are stored in the internal memory. The test set minimizes
the test duration, in order to avoid over-heating the components. The same feature is
available when controlling the test set via PC by PADS.
 Power Factor & Capacitance Diagnostic System for Power Apparatus
7

Power Factor, Capacitance, Dissipation Factor and Tan Delta

for CT, VT, Power Transformer and CB

Power Factor, Capacitance and Tan Delta

The test is performed connecting TDX 5000 to the high AC voltage
source to test target.
Input parameters are: Winding, test voltage and frequency, test
mode, and the nominal capacitance, PF, DF.

The display shows the following data:

• Test voltage, current and frequency
• Capacitance
• Tan Delta and power factor
(absolute 0-1 or percentage 0 -1,0000% values)
• Power data: active, reactive and apparent
• Impedance: module, argument and components

It is possible to apply automatic temperature compensation in the

range 5 ÷60°C with reference temperature 20°C.

It is also possible to calculate some equivalent parameters at

different voltages (for example watt loss and current at 10 kV).

No-Load / Excitation Current

The test is performed connecting TDX 5000 to the high AC voltage

source to the test target.
Input parameters are: the tap number, the type of Tap changer,
the test voltage and the frequency.
The test set applies the high voltage and measures the output
current during the test.
The display shows:
• The test voltage
• The current and the phase shift (inductive, resistive, capacitive)
• The power losses
• The reactance

Ratio with TD

The test is performed connecting TDX 5000 to the RTD option.

The Ratio test is performed by measuring the RTD sample
capacitance two times.
Input parameters are: the tap number, voltages primary and
secondary side, vector group, nominal ratio, test voltage and
frequency, the nominal RTD capacitance.
The display shows the following data:
• Test voltage, nominal capacitance
• Voltage, current, angle, high voltage side
• Measured capacitance
• Ratio
 TDX 5000
8

Other Functions
Pads Software

The PADS software is a powerful application, included in the

TDMS software, which provides connectivity to the instruments
of the STS family. The software performs various tasks, such as:
• Edit and upload to the instrument the test headers
• Create and modify plans containing one or more tests
• Optionally remote control of the execution of test
plans (start, interruption, results assessment)
• Download and save results of tests previously
performed by the instrument
• Open and save results on the PC
• Print test results
• Export test results (excel, CSV, DOC, RPT, PDF,JPEG, XMLformat)

TDX 5000 Specification

Generator Characteristics
typical: ± 0.03% of the value ± 0.1 pF; guaranteed:
MAX VOLTAGE CURRENT MAX OUTPUT
FREQUENCY < 0.1% of the value +1 pF (from 45 to 70 Hz)
OUTPUT OUTPUT DURATION
Hz
V A T Max
• Measurement range 2: from 5 µF to 200 µF. Resolution: 6 digits (or
12000 300 mA 240 s 1 to 500
0.01 nF). Accuracy, tipical: ±0.1% of the value ±0.1 nF, guaranteed:
12000 125 mA > 1 hour 1 to 500
<0.5% of the value ±1 nF
12000 100 mA steady 1 to 500
Tan Delta or dissipation factor DF
Note1: the maximum voltage output may decrease for frequency The TDX5000 can measure Tan delta or Dissipation factor between
below 45Hz and above 400Hz. 0 and more than 100%. There are 3 automatic ranges:
Note2: at 10 kV the output (current value and duration) has the
same characteristic. • Measurement range 1: from 0 to 10% (capacitive).
Note3: output power is 3.6 kVA @12 kV @240 s Resolution: 6 digits (or 0.000001%); accuracy, typical: 0.05% of the
value ± 0.005 %; guaranteed: 0.1% of the value ± 0.005 % (from 45
Voltage and current output metering accuracy to 70 Hz, current < 10 mA)
and resolution
• Measurement range 2: from 0 to 100%. Resolution: 6 digits (or
INTERNAL RESOLUTION TYPICAL GUARANTEED 0.00001%); accuracy, typical: 0.3% of the value ± 0.01 %; guarante-
MEASURE ACCURACY ACCURACY
ed: 0.5% of the value ± 0.02 %
±% ±% ± % (rdg) ± % (rg)
(rdg) (rg)
• Measurement range 3: over 100%. Resolution: 6 digits; accuracy,
12.000 V AC 1V ±0,2% ±0,5 V <0,3% +1V typical: 0.5% of the value ± 0.03 %; guaranteed: 0.8% of the value
5 A AC ± 0.05 %
(10A AC @10s
model PII50185) 0,1 mA ±0,2% ±1 mA < 0,5% < 0,5%
(@ inputs A o B> Power factor PF (or cos(φ))
10 mA)
The TDX5000 can measure power factor between 0 and 100%.
<10 mA AC
(@ inputs A o B) 0,1 µA ±0,2% ±0,1 μA < 0,3% +0,1 μA There are 2 automatic ranges:
• Measurement range 1: from 0 to 10% (capacitive). Resolution: 6
• Frequency range: 1 ÷ 500 Hz digits (or 0.000001); accuracy, typical: 0.05% of the value ± 0.005 %;
• Connections: by a double shielded HV connector, two guaranteed: 0.1% of the value ± 0.005 % (from 45 to 70 Hz, current
Ground sockets (case and external shield of HV cable), and two < 10 mA)
measurement sockets (A and B) • Measurement range 2: from 0 to 100%. Resolution: 6 digits (or
• All measuring are indipendent by the power supply and for 0.00001); accuracy, typical: 0.3% of the value ± 0.02 %; guaranteed:
this they are repetible. The voltage generator is independent by 0.5% of the value ± 0.02 %
the power supply.
Impedance
Test Measurements From 1kOhm to 1400 MOhm. Accuracy, typical 0.3% of the value ±
0.1%, guaranteed <0.5% of the value. Resolution: 6 digits.
Capacitance
Power dielectric losses
The TDX5000 can measure capacitance between 0 and 200 μF.
There are 2 automatic ranges: Measurement ranges: from 0 to 10kW or 100kW or 1mW. Resolution
• Measurement range 1 The TDX5000 can measure capacitance (6 digits): 0.1 mW; accuracy: <0.5% of the value ± 1 mW. The same
between 0 and 200 μF. There are 2 automatic ranges: from ranges and accuracies are applied to reactive and apparent power
0 pF to 5 µF. Resolution: 6 digits (or 0.01 pF). Accuracy, measurements
 Power Factor & Capacitance Diagnostic System for Power Apparatus
9

Inductance Dimensions: 450 (W) x 530 (H) x 215 (D) mm

The TDX5000 can measure inductance between 1 H and 200 10 MH.
Weight: 39 kg
There are 2 automatic ranges:
• Measurement range 1: from 1 H to 10 kH. Resolution (6 digits): Protections
0.1 mH; accuracy, typical: 0.3% of the value ± 0.5 mH; guaranteed: • Short circuit protection: if maximum current limits and time
0.5% of the value duration of power transformer generators are trespassed, the
• Measurement range 2: from 100 H to 10 MH. Resolution (6 digits): generation is interrupted, and the operator is warned by an alarm
1 H; accuracy, typical: 0.3% of the value; guaranteed: <0.5% of the message.
value
• Emergency switch: if emergency pushbutton is pressed,
No Load / Excitation current all main generation will stop immediately.
The TDX5000 can measure no load / excitation current between 0 • High Voltage Lock: the HV output is controlled by a key lock. if
and 300 mA. There are 2 automatic ranges: not turned on, the HV output will be not generated.
• Range 1: 10 mA. Resolution: 0.1 µA; accuracy, typical: 0.2% of the • Ground Detection: if the test set is not connected to the ground,
value ± 0.1µA; guaranteed: 0.3% of the value ± 0.1µA it does not allow power generation and warns the
operator with a diagnostic message and a fixed led light
• Range 2: 300 mA. Resolution 1 mA; accuracy, typical: 0.2% of the • Warning Strobe Light
value ± 1 mA; guaranteed: 0.5% of the value ± 0.5% of the range • Remote Safety Switch

Output frequency Accessories Supplied

AC output frequency range: 1 to 500 Hz Connection Cables
• One mains supply cable, 2 m long
Max interference conditions at line • One grounding cable, 6 m long as standard or as option with
• Electrostatic: 15 mA rms of the interference current into any lead increased lenght
or cable with no loss of measurement accuracy. Applicable to a • One ETHERNET interface cable
maximum ratio of interference current to specimen current 20:1 • One USB pen drive
• Electromagnetic: 500 µT, at 50/60 Hz in any direction • 1 High voltage coaxial cable double shielded, 20 m long, 25 kV,
with earth screen, for the connection to the device under test,
Digital input terminated on the device side with an isolated tearproof plug
Binary input used only for RCTD - Compensating reactor option or hook and on the TDX 5000 side with two plugs: one for the
HV and the other one for the ground. The cable is mounted on
Display a wheel
The large graphic display has the following characteristics: • 1 clamp, 25 mm opening, with a connector which mates with
• Pixels: 640 x 480, coloured the HV cable
• LCD type: TFT • 1 bigger clamp, 60 mm opening, with a connector which mates
• View area: 132 x 99 mm with the HV cable
• Backlight • 2 shielded connection cables, 20 m long, for the connection to
the metering points. Terminated on the TDX 5000 side with the
Local test set control metering connector and on the device side with a plug. Cables
Local test control: by the START / STOP pushbutton. After the test are mounted on wheels
selection, pressing it, the output is generated, according to the • 2 clamps, 25 mm opening, terminated with sockets, which
type of test. During ON, if a manual control test is selected, the allow connecting to the metering point
operator adjusts the output at the desired value. • 2 Kelvin type clamps, 65 mm opening, with plugs, which allow
Test saving: connecting to the metering point
• Automatic save • 1 hot collar cable, 1m long, with connector
• After operator confirmation
Transport Case
Other Characteristics As option, transport case with wheels and handles, with IP67
to protect against dust and water. The transport case allows
Communication interfaces
delivering TDX 5000 with no concern about shocks up to a fall
• Slave USB and ETHERNET for the PC connection of 1 m.
• USB port for the USB key
Interfaces to external modules:
• Alarms to a flashing light
• Remote start input
Main supply
• 100-230 V ± 15%; (85 ÷ 264V); 47÷63 Hz
• Maximum supply current: 16 A
• Standard plug: schuko
Other plugs: on requirement (for example with socket type CEE,
NEMA, CEI, BS, AS and others)

Heavy duty transport case

 TDX 5000
10

Optional Accessories CAP - CAL Calibrator Module

RCTD Compensating Reactor Purpose of the calibrator is to check the correctness of TDX 5000
measurement. The calibrator includes an extremely high accuracy
This module is useful for testing Tan Delta in rotating machines high voltage capacitor, which comes with a certificate issued by ISA
with TDX 5000 and allows increasing the test current and getting lab.
the maximum test voltage with high capacitive burdens. Each
RCTD is composed by two inductors with a nominal value of
40H and a steady current of 0.4A. The maximum current on each
inductor can be up to 1A for more than 10s. The inductors can
be connected in parallel on the load in order to increase the test
frequency. It is possible to connect two RCTD in parallel in order
to have three or four inductors connected together (2 x 80 H total).

CAP - CAL

STOIL Cell for the HV Test of the Dielectric Oil

The option allows testing (Power Factor, Capacitance and Tan
Delta) that the oil characteristics of isolation are met and that there
is no contamination.
The option is made of a suitable glass container with electrodes;
RCTD the electrodes are connected to TDX 5000 for the test execution.
The test result, displayed by TDX 5000, is the oil Tan Delta. Cell
characteristics are the followings:
• Maximum test voltage: 12 kV
Digital Thermo Hygrometer • Cell volume: about 1l
• Capacitance of the empty cell: 60 pF
Tan Delta tests are influenced by temperature and humidity.
The option allows measuring these parameters and to input
them into the test settings. Meter characteristics:
• Temperature range: -10÷60°C
• Temperature measurement accuracy: ± 0.4°C
• Humidity measurement range: 5÷5% RH
• Accuracy of humidity measurement: ± 2.5% RH, over the whole
range
• Dimensions: 141 x 71 x 27 mm. Weight: 150 g

Oil cell

Digital Thermo Hygrometer

 Power Factor & Capacitance Diagnostic System for Power Apparatus
11

RTD Capacitance for transformer ratio at Applicable Standards

high voltage
The test set conforms to the EEC directives regarding
This option allows to measure the turn ratio of the transformers
Electromagnetic Compatibility and Low-Voltage instruments.
using the high voltage generator up to 12kV. The RTD is a simple
capacitance turn ratio precision: 0.1% • Electromagnetic Compatibility: Directive 2014/30/UE.
Applicable Standard: EN61326-1:2013; IEC61000-6-5
Remote Safety Switch • Low Voltage Directive: Directive n. 2014/35/UE.
It’s possible add further remote safety switch with cable length Applicable standards: CEI EN61010-1:2010
as required. If it is desired to start the test remotely from the test In particular:
set, the optional switch allows to do it, up to the distance of 20 - Input/output protection: IP 2X - IEC69529; IP 4X for HV output
m, which is the length of the cable provided. It’s possible to add - Operating temperature: -10÷55 °C; storage: -20÷70 °C
further remote safety switch with cable length as required. - Relative humidity: 0÷95% without condensing

Warning Strobe Light

The warning strobe light alerts when the test is completed, or when Ordering Information
there are alarms. The light is self-powered, and turns on (flashes)
upon the test set command. A siren is also included. Hook for HV CODE MODULE
connection
In add to the HV clamps included with the standard cable set, it 65175 TDX 5000 - with TDMS software*,
is possible to order an hook to connect the HV cable with internal standard test cable kit
diameter 100 mm and length 250 mm. 38175 and heavy duty transport case
10176T PADS software (trasfo)- Power transformer
Hook for HV connection and Tan Delta test module
In add to the HV clamps included with the standard cable set, it
40175 CAP-CAL Calibration module
is possible to order an hook to connect the HV cable with internal
42175 Remote safety switch
diameter 100 mm and length 250 mm.
44175 Digital thermo hygrometer
IN-A and IN-B current measure inputs up to 10A 43175 Warning strobe light
Optionally IN-A and IN-B current inputs can measure up to 10A for 47175 RCTD - Compensating reactor for TDX 5000
a maximum of 10s. These inputs have the same characteristics as 48175 Cable test kit for RCTD
for standard inputs 5A, refer to chapter 3.3. This option must be 19175 Transport case for RCTD
selected at the order 13175 STOIL Cell for the eletric test of insulating oil
of the transformer
68175 Trolley for TDX 5000
Optional Software 66175 Cable test kit for TDX 5000
41185 RTD capacitance for transformer ratio at
PADS - Power Apparatus Diagnostic Software high voltage
PADS - Power Apparatus Diagnostic Software is a powerful software 42185 Hook for HV connection
application, included in TDMS software, that allow the remote 50185 IN-A and IN-B current measure inputs up to
control of the STS family: STS 5000, STS 4000, TDX 5000. Please 10 A
refer to PADS datasheet for more information. *PADS - Power Apparatus Diagnostic Software is NOT included into
basic unit price. It should be expressly ordered.

Comparison Table of the STS Family

STS MODEL HIGH HIGH LOW TAN DELTA OPTIONAL
CURRENT, VOLTAGE AC-DC TESTS HIGH AC
AC & DC OUTPUTS CURRENT
WITH BUX
STS 5000 1)
with
TD 5000

STS 4000 1) with

NOT AVAILABLE
TD 5000

TDX 5000
NOT AVAILABLE NOT AVAILABLE NOT AVAILABLE NOT AVAILABLE

1)
For USA and Germany, only TDX 5000 and STS 3000 light with TD 5000 are available.
 Comparison Table of the STS Family Tests
NO. TEST OF TEST DESCRIPTION STS 5000 STS 4000 TDX 5000

1 CT Ratio, Voltage mode NOT AVAILABLE

2 CT Ratio, polarity and burden with high AC current
WITH BUX NOT AVAILABLE
3 CT Burden; secondary side NOT AVAILABLE
4 CT Excitation curve NOT AVAILABLE
5 CT Winding or burden resistance NOT AVAILABLE
6 CT Voltage withstand NOT AVAILABLE
7 CT Remote polarity check NOT AVAILABLE NOT AVAILABLE
8 CT Rogowski coil transformers WITH BUX NOT AVAILABLE
9 CT Low power transformers WITH BUX NOT AVAILABLE
10 CT Tan(δ) measurements WITH TD 5000 WITH TD 5000
11 VT Ratio; polarity NOT AVAILABLE
12 VT Burden, secondary side NOT AVAILABLE
13 VT Ratio, electronic transformers NOT AVAILABLE
14 VT Voltage withstand NOT AVAILABLE
15 VT Remote polarity check NOT AVAILABLE NOT AVAILABLE
16 VT Tan(δ) measurements WITH TD 5000 WITH TD 5000
17 PT Ratio per TAP NOT AVAILABLE
18 TP Vector Group NOT AVAILABLE

19 PT Static and dynamic resistance of Tap Changer NOT AVAILABLE

contacts
20 PT No Load / Excitation current WITH TD 5000 WITH TD 5000
21 PT Short circuit impedance NOT AVAILABLE
22 PT Tan(δ) measurements WITH TD 5000 WITH TD 5000
23 PT Ratio with RTD WITH TD 5000 WITH TD 5000
24 CB High DC current micro-Ohmmeter test NOT AVAILABLE NOT AVAILABLE
25 CB Tan(δ) measurements WITH TD 5000 WITH TD 5000
26 VT CB RELAY Current threshold and timing NOT AVAILABLE
27 R Ground resistance and resistivity NOT AVAILABLE
28 R Step and touch voltages NOT AVAILABLE
29 L Measurement of line impedance and of the NOT AVAILABLE
related parameters
30 Capacitor Measurement of the capacitance WITH TD 5000 WITH TD 5000
Banks
DS TDX 5000 EN - REV. 02/2022

ISA - Altanova Group Srl

Via Prati Bassi 22,
21020 Taino (Va) - ITALY
Phone +39 0331 95 60 81
Email isa@altanova-group.com

www.altanova-group.com

The product and the information contained herein may be changed at any time without prior notification. This document nor any parts thereof may not be reproduced or transmitted in any form either
electronically or mechanically, including photocopying and recording, without the express written consent of ISA - Altanova Group Srl.