MBB HELICOPTERS

MAINTENANCE MANUAL MBB - B0 105.

834 EXTERNAL LOUDSPEAKER SYSTEM B0 105 S

Table of Contents

Paragraph Title Page

834 - 1 DESCRIPTION - .... .
EXTERNAL LOUDSPEAKER SYSTEM B0 105 S 3
834 - 2 TROUBLESHOOTING - EXTERNAL LOUDSPEAKER SYSTEM B0 105 S . . . 5
834 - 3 INSPECTION SCHEDULE - EXTERNAL LOUDSPEAKER SYSTEM B0 105 S . 8
834 - 4 INSPECTION FOR CONDITION - EXTERNAL LOUDSPEAKER SYSTEM
B0 105 S .. ..................... . 9

834 - 5 FUNCTIONAL CHECK - EXTERNAL LOUDSPEAKER SYSTEM B0 105 S . . . 9

834 - 7 Installation - ............... .

loudspeaker 11
834 - 8 Removal - amplifier .................. . 11
834 - 9 Installation- amplifier ................ . 12

B0 105
CHAPTER 834
Page 112
 MBB HELICOPTERS
MAINTENANCE MANUAL MBB - B0 105

834 - 1 DESCRIPTION - EXTERNAL LOUDSPEAKER SYSTEM B0 105 S

1. General

The i n t e g r a t e d loudspeaker system i s i n s t a l l e d i n t h e h e l i c o p t e r f u s e l a g e

between frames 4V and 3B. It i s used by t h e h e l i c o p t e r Crew t o broadcast
messages a t a s u f f i c i e n t loudness l e v e l .

2. Description
The system c o n s i s t s of t h e following components:
- 2 loudspeakers 6TD, 7TD (450 W)
- 1 microphone 5TD
- 1 c o n t r o l u n i t 3TD ( c o n t r o l s volume) with preamplifier W450
- 1 a m p l i f i e r 4TD
- 1 r e l a y 2TD
- 1 c i r c u i t breaker 1TD
- 1 f u s e 9TD

3. Operation
The e x t e r n a l loudspeaker system i s s u p p l i e d with dc voltage from a u x i l i a r y
bus PP22 and i s p r o t e c t e d by c i r c u i t breaker 1TD and fuse 9TD i n c o n t r o l
u n i t 2VE.
Heatset-microphone and hand-held microphone a r e connected t o t h e
p i l o t / c o p i l o t junction box o r t o t h e c o n t r o l u n i t .
Switch SI i s s e l e c t e d t o ON and e n e r g i z e s r e l a y 2TD, a c t i v a t i n g a m p l i f i e r
4TD. Then f o u r - p o s i t i o n s e l e c t o r switch on c o n t r o l u n i t i s s e t t o L/S.

I f t h e t o g g l e switch on t h e junction box i s s e l e c t e d t o L/S-FMI, a l l

on-board mirophones may be operated, with c i r c u i t switching g i v i n g t h e
hand-held microphone p r i o r i t y over t h e headset-microphone. S e t t i n g t h e
t o g g l e switch t o ON enables t h e loudspeaker system t o be operated from a
ground s t a t i o n using t h e h e l i c o p t e r a s a r e l a y s t a t i o n .

B 0 105
CHAPTER 834
Page 3
 MBB HELICOPTERS
MAINTENANCE MANUAL MBB - B0 105

1 Amplifier
2 Control u n i t
3 C i r c u i t breaker
4 Loudspeaker

Fig. 834-1 External loudspeaker system B0 105 S

B0 105
CHAPTER 834
Page 4
 MBB HELICOPTERS
MAINTENANCE MANUAL MBB - B0 105

834 - 2 TROUBLESHOOTING - EXTERNAL LOUDSPEAKER SYSTEM B0 105 S

General
- Troubleshoot i n conjunction with wiring diagram 834-1 i n t h e Wiring
Diagram Manual (WDM) .
- Where possible, check t h a t a l l a s s o c i a t e d e l e c t r i c a l connections a r e t i g h t
and secure.
- Functionally check c i r c u i t breaker SPEAKER 1TD and o t h e r system switches.

- Connect e x t e r n a l power supply (EPU) and s e l e c t b a t t e r y switch 16P on

instrument panel t o BATT OFF/EPU ON.
- Depress c i r c u i t breaker SPEAKER.

No. TROUBLE SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION

1 The loudspeaker Defective c i r c u i t Check c i r c u i t breaker

system does not breaker 1TD f o r c o n t i n u i t y and
operate v i a connections f o r proper
hand-held o r c o n t a c t . Replace
headset-microphones defective parts

Defective fuse 9TD Check fuse f o r

( c o n f i g u r a t i o n I1 only) c o n t i n u i t y . Replace
i f defective
Defective f u s e S i 1 i n Check fuse f o r
c o n t r o l u n i t 3TD .
c o n t i n u i t y Replace
i f defective

Defective t o g g l e switch Inspect toggle switch

S1 i n c o n t r o l u n i t 3TD f o r c o n t i n u i t y and
connections f o r proper
.
contact Replace
defective parts

Defective r e l a y 2TD Check r e l a y f o r voltage

between pins A l and X2.
Replace r e l a y i f
no voltage i s present

Table 834-1 Troubleshooting (1 of 3)

B 0 105
CHAPTER 834
Page 5
 MBB HELICOPTERS
MAINTENANCE MANUAL MBB - B0 105

TROUBLESHOOTING (continued)

No. TROUBLE SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION

One o r more defective Check fuses f o r

fuses ( S i 101, S i 102, c o n t i n u i t y . Replace
S i 103) i n f i n a l d e f e c t i v e fuses
amplifier 4TD

Defective preamplifier Replace preamplifier

3TD
Defective f i n a l amplifier Replace f i n a l amplifier
4 TD

Defective wiring Check wiring f o r

c o n t i n u i t y using
relevant wiring
diagram. Repair
o r replace defective
part s
2 No broadcasting Defective press-to-talk Check press-to t a l k
through loudspeaker on corresponding c y c l i c switch and replace
system from headset pitch stick a s necessary
microphone

Defective headset Replace headset

microphone
Defective s t a t i o n box Replace affected
s t a t i o n box
Refer t o item no. 1 Refer t o item no. 1
3 No broadcasting Defective press-to-talk Check press-to-talk
through loudspeaker switch i n hand-held switch and, i f
system from microphone or hand-held necessary, replace
hand-held Mcrophone microphone defective hand-held.microphone
Refer t o item no. 1 Refer t o item no. 1
4 Broadcasting from Defective loudspeaker, Reverse connector
one speaker only f i n a l s t a g e fuse or 4TDc and TDd i n
f i n a l stage speaker outputs on
f i n a l amplifier 4TD

Table 834-1 Troubleshooting ( 2 of 3)

B0 1 0 5
CHAPTER 834
Page 6
 MBB HELICOPTERS
MAINTENANCE MANUAL MBB - B0 105
TROUBLESHOOTING (continued)

No. TROUBLE SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION

- After connector
reversal, broad-
casting from other
speaker only:
Check fuses S i 1 0 1 and
S i 103 i n f i n a l
amplifier 4TD and
replace as necessary.
Replace f i n a l amplifier
i f fuses a r e i n t a c t
- Broadcast from
Same speaker
a f t e r connector
reversal:
Replace inoperative
speaker

Scratched or Defective speaker Replace speaker

distorted membrane
transmission
Magnetic s l o t of one Clean magnetic s l o t
of t h e speakers
defective

Scratch noises occur Defective slide-actuated Replace potentiometer

when the audio potentiometer i n
l e v e l control i s preamplifier 3TD
operated

Table 834-1 Troubleshooting (3 of 3)

B0 105
CHAPTER 834
Page 7
 EUROCOPTER MAlNTENANCE MANUAL B 0 105

1 834 - 3 INSPECTION SCHEDULE (refer to Chapter 101)

CHAPTER 834 Revision 18

Page 8
 MBB HELICOPTERS
MAINTENANCE MANUAL MBB - B0 105
834 - 4 INSPECTION FOR CONDITION - EXTERNAL LOUDSPEAKER SYSTEM B0 105 S

1. Pul1 c i r c u i t breaker 1TD and unscrew and remove f u s e 9TD from instrument
panel .
2 . Remove turnlock f a s t e n e r s and Cover (4, f i g . 834-2).
Unscrew r i g h t and l e f t f a i r i n g s ( 6 ) and remove them downward from t h e
a i r f rame .
3 . Inspect loudspeaker ( 7 ) and mounting bracket f o r cracks, deformation,
o t h e r mechanical damage, corrosion,'damaged s u r f a c e p r o t e c t i o n , and
s e c u r i t y of i n s t a l l a t i o n .
a. Replace mounting bracket i f cracked o r defomed.

b. P o l i s h out mechanical damager corrosion, and damage t o surface

p r o t e c t i o n using 400 g r i t abrasive c l o t h . A f t e r applying wash primer
(CM 423), touch up with s i n g l e - l a y e r lacquer (CM 407).

C. Tighten loose a t t a c h i n g hardware.

4 . Repair o r r e p l a c e damaged e l e c t r i c a l cable.

5 . Inspect e l e c t r i c a l connections f o r condition and s e c u r i t y ; replace damaged

p a r t s and t i g h t e n l o o s e connector.
6. Replace missing o r damaged lockwires.
7 . Inspect a m p l i f i e r ( 2 ) f o r s e c u r i t y of i n s t a l l a t i o n ; t i g h t e n loose
a t t a c h i n g hardware a s necessary.

8. Inspect p r e a m p l i f i e r f o r s e c u r i t y of i n s t a l l a t i o n , t i g h t e n loose a t t a c h i n g
hardware a s necessary.

834 - 5 FUNCTIONAL CHECK - EXTERNAL LOUDSPEAKER SYSTEM B0 105 S

1. Connect e x t e r n a l power supply (EPU) and s e l e c t b a t t e r y switch 16P on

instrument panel t o BATT OFF / EPU ON.

2 . Press c i r c u i t breaker SPEAKER on instrument panel; p r e s s c i r c u i t breaker

on p i l o t / c o p i l o t s t a t i o n box.

3 . S e l e c t t o g g l e switch SI on c o n t r o l u n i t 3TD t o ON; r e s e t volume c o n t r o l t o

V.

4 . Move s e l e c t o r switch on c o n t r o l u n i t t o L/S.

B 0 105
CHAPTER 834
Page 9
 MBB HELICOPTERS
MAINTENANCE MANUAL MBB - B 0 105

5. Connect headset-microphone and hand-held microphone.

6. Broadcast through t h e loudspeaker system by speaking i n t o t h e hand-held

microphone. A t t h e Same time, t u r n up t h e volume a t t h e volume c o n t r o l .

7. Move toggle switch i n junction box t o L/S-FMI.

8. Press p r e s s - t o - t a l k button on c y c l i c s t i c k and make a t e s t broadcast v i a

t h e headset-microphone.

9. Verify p r i o r i t y of t h e hand-held microphone by simultaneously pressing

t h e press-to-talk buttons of t h e hand-held microphone and t h e
headset-microphone.

10. Switch o f f c o n t r o l u n i t 3TD and pul1 c i r c u i t breaker SPEAKER and c i r c u i t

breaker on p i l o t / c o p i l o t s t a t i o n box.

834 - 6 Removal - loudspeaker

1. Pul1 c i r c u i t breaker 1TD and unscrew and remove f u s e 9TD on instrurnent
panel .
2. Remove t u r n lcck f a s t e n e r s and Cover ( 4 , f i g . 834-2). Unscrew r i g h t and
l e f t f a i r i n g s (6) and remove them downward from t h e airframe.
3. Disconnect angle connectors (8 and 6, f i g . 834-3) of r i g h t and l e f t
loudspeaker f rom amplif i e r (1).
4. Unscrew bonding jumpers ( 4 and 5) f rom mounting bracket; disconnect
e l e c t r i c a l l e a d from a n t i - c o l l i s i o n l i g h t (5, f i g . 834-2).
5. Remove clamps (10, f i g . 834-3) from mounting bracket. Remove four screws
(1, f i g . 834-2) from each loudspeaker and remove loudspeaker.

B 0 105
CHAPTER 834
Page 1 0
 MBB HELICOPTERS
MAINTENANCE MANUAL MBB - B0 105

834 - 7 Installation - loudspeaker

Install loudspeaker in reverse order of removal.

1 Screw
2 Amplifier 4TD
3 Cover
4 Cover
5 Anti-collision light
6 Fairing
7 Loudspeaker

Fig. 834-2 Removal and installation - loudspeaker

834 - 8 Removal - amplifier

1. Pul1 circuit breaker 1TD and unscrew and remove fuse 9TD.
2. Remove turnlock fasteners and cover (4, fig. 834-2).
3. Disconnect electrical lead from anti-collision light (5) and disconnect
angle connectors (6, 7 and 8, fig. 834-3) from amplifier (1); unscrew and
remove bonding jumper (9).
4. Remove four screws from cover (2) and two screws (11) from mounting
bracket. Remove cover by pulling downward and carefully pul1 amplifier out
of mounting bracket.

B0 105
CHAPTER 834
Page 11
 MBB HELICOPTERS
MAINTENANCE MANUAL MBB - B0 105

834 - 9 Installation - amplifier

I n s t a l l a m p l i f i e r i n r e v e r s e order t o removal.

1 Arnplifier
2 Cover
3 Loudspeaker
4 Bonding jumper RH
5 Bonding jumper LH
6 Angle connector LH
7 Angle connector ( a m p l i f i e r )
8 Angle connector RH
9 Bonding jumper ( a m p l i f i e r )
10 Clamps
11 Screws (mounting b r a c k e t )

Fig. 834-3 Removal and i n s t a l l a t i o n - amplifier

BQ 105
CHAPTER 834
Page 12