Ohp (2171912)

ALPHA COLLEGE OF ENGINEERING & TECHNOLOGY
ODD SEM 2018

SUB : OHP (2171912) 7TH SEM
ASSIGNMENT 1
Ch. 1 Introduction
Sr. No. Questions Marks Year
7 Nov-16
1. Explain open loop closed circuits and closed loop closed circuits for hydrostatic systems.
7 Nov-16
2. Basic Components of a Hydraulic System
3. Explain Brahma‟s press principle with the help of neat sketch. 3 May-17
7 May-17
4. Compare advantages and disadvantages of pneumatic and hydraulic system?
5. Draw the general layout of hydraulic system. Explain the function of each component. 3 Nov-17
3 Nov-17
6. Distinguish between Hydraulic system & Pneumatic system.
3 Nov-17
7. List the electric devices used in the control of fluid power system.
8. Write a note on thermocouple type temperature sensor 4 Nov-17
Give ISO/ANSI symbol of following. 7 Nov-17
1. Unidirectional fixed displacement hydraulic pump
2. Single acting cylinder with spring return
3. 4/3 DCV
4. FRL unit
9. 5. Variable restriction flow control valve
6. Spring loaded accumulator
7. Air filter
Subject In Charge HOD

ODD SEM 2018
ASSIGNMENT 2
Ch. 2 System Components, Hydraulic Oils, Fluid Properties and Filter

What is a by-pass filter? State its advantages and disadvantages. 7 Nov-16

1.
7 Nov-16
2. Advantages and disadvantages of High - Water Content Fluid (HWCF).
Name and explain the properties of hydraulic oil used in hydraulic 7 May-17
3.
circuit.
7 Nov-17
4. Draw Symbol of filter & explain the working of by-pass type filter

ODD SEM 2018
ASSIGNMENT 3
Ch. 3 Hydraulic Pumps, Motors and Actutors

7 Nov-16
1. Construction and working of an internal gear pump.
Explain control of a bi-directional motor by 4/2 way valve. 7 Nov-16
2.
3. Differentiate between a hydrostatic and hydrodynamic system. 7 Nov-16, Nov-
7 17
May-17
Classify hydraulic pumps. Explain the principle of working of a
4. positive displacement pump.
Explain the working of balanced vane pump with the help of neat 7 May-17
5.
sketch.
Show the construction of double acting cylinder with labelled diagram. 7 May-17
6.
Give the classification of Pumps. Sketch & Explain working of internal 7 Nov-17
7.
gear pump.
8. Sketch & Explain the working of Ge- rotor pump. 4 Nov-17
9. What is an actuator? Give the classification of hydraulic actuators. 3 Nov-17

ODD SEM 2018
ASSIGNMENT 4
Ch. 4 Hydraulic Valves and Hydraulic System Accessories

Cite the classification of check valves and explain the function of pilot-operated 7 Nov-16
1. check valve, giving the necessary drawing.
2. State the different ways of control of DCVs. 7 Nov-16
3. Draw the symbols of Pressure control valves used in hydraulic systems. 7 Nov-
16
Draw the symbols for following hydraulic components according to ISO: (A) 4 May-17
4. Double acting cylinder with cushioning on both sides (B) Lever operated, spring
returned, 3/2 DCV (C) Pilot operated check valve (D)Sequence valve.
List different types of accumulators and describe functioning of any two with the 7 May-17
5. help of neat sketch.
Explain the working of “Pilot operated, spring centered 4-port, 3-position 7 May-17
6. direction control (spool) valve” with the help of neat sketch.
List different pressure control valves giving its application. Explain construction and 7 May-17
7. working of any one in detail with the help of neat sketch.
What do you mean by pressure relief valve? sketch & explain with neat sketch 7 Nov-
8. the working of pilot operated pressure relief valve (Compound Relief valve) 17
4 Nov-
9. List the Power loss in flow control circuits & explain in detail.
17
3 Nov-
10. Explain 4/3 sliding spool direction control valve working. 17
7 Nov-
11. Describe Working of sequence valve with neat sketch & draw its symbol
17

ODD SEM 2018
ASSIGNMENT 5
Ch. 5 Design of Hydraulic Circuits

Sr. Questions Marks Year
No.
A single acting cylinder is to be operated from two different sources A and B Nov-16
such that its forward motion can be actuated from either of the two locations. 7
1.
Draw and explain a circuit diagram.
Explain the control of a surface grinder table by pilot-operated valve with detail Nov-16
2. 7
drawing.
Differentiate between direct and indirect control. Draw simple hydraulic circuit Nov-16
3. 7
diagrams of both and explain the differences.
Draw a hydraulic circuit diagram of a hydraulic system having a double acting Nov-16
cylinder which has a rapid approach speed, than slow feed motion and at the 7
4.
end of the stroke the cylinder returns rapidly.
Draw and explain the working of „Sequential circuit‟ for sequential operation 7 May-17
5. of two - double acting cylinders, using two sequence valves.
Draw and explain the working of „Regenerative circuit‟ for achieving same 7 May-17
6. speed of double acting cylinder in both strokes.
3 Nov-17
7. Draw speed controlled actuator, Meter- out circuits for DAC for extension.
7 Nov-17
8. Draw the hydraulic circuit for Drilling machine & explain its working.
7 Nov-17
9. Bleed off Circuits – sketch & explain its working.

ODD SEM 2018
ASSIGNMENT 6
Ch. 6 Introduction to Pneumatic Systems

7 Nov-16
1. Construction and working of time delay valve of pneumatic systems.
7 Nov-
2. List the six basic components used in a pneumatic system.
16,
7 May-17
Nov-17
3. Compare advantages and disadvantages of pneumatic and hydraulic system?
7 May-17
4. Explain construction & working of pressure regulator used in pneumatic system.
With the help of neat sketch, explain the principle and working of Shuttle valve (OR gate) 7 May-
5. and Twin Pressure valve (AND gate). 17,
7 Nov-
Nov-17
Give ISO/ANSI symbol of following.
1. Unidirectional fixed displacement hydraulic pump 17
2. Single acting cylinder with spring return
3. 4/3 DCV
4. FRL unit
6. 5. Variable restriction flow control valve
6. Spring loaded accumulator
7. Air filter
If diameter of piston is 60 mm, diameter of piston rod is 10 mm, & air pressure is 100 4 Nov-
7. N/mm2, what will be the force in advance stroke & return stroke. 17

ODD SEM 2018
ASSIGNMENT 7
Ch. 7 Pneumatic Circuits

Design a circuit to control speed of a double acting pneumatic cylinder in both the 7 May-17
1. strokes and explain its working.
What is functional diagram in pneumatic circuit? Explain Movement diagram, 7 May-17

2. Travel-Time diagram and Position-step diagram with the help of an example.
7 Nov-17
3. Sketch & explain Pneumatic Circuit using Quick Exhaust valve.
7 Nov-17
4. Draw Pneumatic circuit for operating DAC by 4/3 DCV.
7 Nov-17
5. Draw Throttle-out circuits for extension stroke for pneumatic system.

ODD SEM 2018
ASSIGNMENT 8
Ch. 8 Introduction to Automation

4 Nov-
1. What do you mean Automation? Give classification of Automation. 17

Ohp (2171912)

Uploaded by

Copyright:

Available Formats

Ohp (2171912)

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ohp (2171912)

Uploaded by

Copyright:

Available Formats

ALPHA COLLEGE OF ENGINEERING & TECHNOLOGY

ODD SEM 2018

Subject In Charge HOD

Ch. 2 System Components, Hydraulic Oils, Fluid Properties and Filter

What is a by-pass filter? State its advantages and disadvantages. 7 Nov-16

Subject In Charge HOD

Ch. 3 Hydraulic Pumps, Motors and Actutors

9. What is an actuator? Give the classification of hydraulic actuators. 3 Nov-17

Subject In Charge HOD

Ch. 4 Hydraulic Valves and Hydraulic System Accessories

Subject In Charge HOD

Ch. 5 Design of Hydraulic Circuits

Subject In Charge HOD

Ch. 6 Introduction to Pneumatic Systems

Subject In Charge HOD

Ch. 7 Pneumatic Circuits

What is functional diagram in pneumatic circuit? Explain Movement diagram, 7 May-17

Subject In Charge HOD

Ch. 8 Introduction to Automation

Subject In Charge HOD

You might also like