Operator's Manual: VO-360 & IVO-360 Helicopter Engines
Operator's Manual: VO-360 & IVO-360 Helicopter Engines
TEXTRON Lycoming
Approved by F.A.A.
2nd Edition Part No. 60297-11
All brand and product names referenced in this publication are trademarks or registered
trademarks of their respective companies.
Mailing address:
Textron Lycoming
652 Oliver Street
Williampsort, PA 17701 U.S.A.
Phone:
Factory: 570-323-6181
Sales Department: 570-327-7268
Fax: 570-327-7101
Textron Lycoming's regular business hours are Monday through Friday from 8:00
A.M. through 5:00 P.M. Eastern Time (+5 GMT)
ATTENTION
This operator's manual contains a description of the engine, its specifications, and detailed information on
how to operate and maintain it. Such maintenance procedures that may be required in conjunction with
periodic inspections are also included. This manual is intended for use by owners, pilots and maintenance
personnel responsible for care of Textron Lycoming powered aircraft. Modifications and repair procedures
are contained in Textron Lycoming overhaul manuals; maintenance personnel should refer to these for such
procedures.
SAFETY WARNING
Although the information contained in this manual is up-to-date at time of publication, users are urged to
keep abreast of later information through Textron Lycoming Service Bulletins, Instructions and Service
Letters which are available from all Textron Lycoming distributors, or from the factory by subscription.
Consult the latest edition of Service Letter No. L114 for subscription information.
SPECIAL NOTE
The illustrations,pictures and drawings shown in this publication are typical of the subject
matter they portray; in no instance are they to be interpreted as examples of any specific
engine, equipment or part thereof
iii
TEXTRON LYCOMING OPERATOR'S MANUAL
Proper service and repair is essential to increase the safe, reliable operation of all aircraft engines. The
service procedures recommended by Textron Lycoming are effective methods for performing service
operations. Some of these service operations require the use of tools specially designed for the task. These
special tools must be used when and as recommended.
It is important to note that most Textron Lycoming publications contain various Warnings and Cautions
which must be carefully read in order to minimize the risk of personal injury or the use of improper service
methods that may damage the engine or render it unsafe.
It is also important to understand that these Warnings and Cautions are not all inclusive. Textron
Lycoming could not possibly know, evaluate or advise the service trade of all conceivable ways in which
service might be done or of the possible hazardous consequences that may be involved. Accordingly,
anyone who uses a service procedure must first satisfy themselves thoroughly that neither their safety nor
aircraft safety will be jeopardized by the service procedure they select.
WARRANTY
NEW AND REBUILT ENGINES
(1) WARRANTY AND REMEDY: Lycoming Engines, a division of Avco Corporation (hereinafter “Lycoming”)
warrants each new Lycoming reciprocating engine to be free from defect in material or workmanship under normal
use and service. Lycoming’s sole obligation under this warranty is limited to replacement or repair of parts which
are determined by Lycoming to have been defective within a period of twenty-four (24) months after new aircraft
delivery to the original retail purchaser or first user, or twenty-four (24) months from the date of first operation. The
warranty period of twenty-four (24) months commences on the earlier of the date of first operation after new aircraft
delivery to the original retail purchaser or first user, or twenty-four (24) months from the date of shipment from
Lycoming. Lycoming will, in connection with the foregoing warranty, cover reimbursement of reasonable freight
charges with respect to any such warranty replacement or repair.
(2) Within the warranty period, Lycoming will reimburse the Purchaser for labor charges associated with warranty
related issues. Lycoming will only reimburse the cost of such labor charges in connection with repair or
replacement of parts as provided in Lycoming’s then current Removal and Installation Labor and Allowance
Guidebook. Spare parts installed as warranty replacement on engines which are covered by this New Engine
Warranty will be warranted for the balance of the original warranty period or for the spare part warranty, whichever
is the greater. Replacement of parts may be with either new or reconditioned parts, at Lycoming’s election. A claim
for warranty on any part claimed to be defective must be reported in writing to Lycoming’s Warranty
Administration within 60 days of being found to require repair or replacement by the purchaser or service facility.
Warranty adjustment is contingent upon the Purchaser complying with the Lycoming’s Warranty Administration
disposition instructions for defective parts. Failure to comply with all of the terms of this paragraph may, at
Lycoming’s sole option, void this warranty.
(3) THIS WARRANTY IS GIVEN AND ACCEPTED IN PLACE OF (i) ALL OTHER WARRANTIES OR
CONDITIONS, EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES
OR CONDITION OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE AND (ii) ANY
OBLIGATION, LIABILITY, RIGHT, CLAIM OR REMEDY IN CONTRACT OR IN TORT (DELICT),
INCLUDING PRODUCT LIABILITIES BASED UPON STRICT LIABILITY, NEGLIGENCE, OR IMPLIED
WARRANTY IN LAW AND PURCHASER HEREBY WAIVES SUCH RIGHTS AND CLAIMS.
(4) THIS WARRANTY IS THE ONLY WARRANTY MADE BY LYCOMING. THE PURCHASER’S SOLE
REMEDY FOR A BREACH OF THIS WARRANTY OR ANY DEFECT IN A PART IS THE REPAIR OR
REPLACEMENT OF ENGINE PARTS AND REIMBURSEMENT OF REASONABLE FREIGHT CHARGES AS
PROVIDED HEREIN. LYCOMING EXCLUDES LIABILITY, WHETHER AS A RESULT OF A BREACH OF
CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO, DAMAGE TO THE ENGINE OR
OTHER PROPERTY (INCLUDING THE AIRCRAFT IN WHICH THE ENGINE IS INSTALLED), COSTS AND
EXPENSES RESULTING FROM REQUIRED CHANGES OR MODIFICATIONS TO ENGINE COMPONENTS
AND ASSEMBLIES, CHANGES IN RETIREMENT LIVES AND OVERHAUL PERIODS, LOCAL CUSTOMS
FEES AND TAXES, AND COSTS OR EXPENSES FOR COMMERCIAL LOSSES OR LOST PROFITS DUE TO
LOSS OF USE OR GROUNDING OF THE AIRCRAFT IN WHICH THE ENGINE IS INSTALLED OR
OTHERWISE. LYCOMING’S TOTAL LIABILITY FOR ANY AND ALL CLAIMS RELATED TO ANY
ENGINE SHALL IN NO CASE EXCEED THE ORIGINAL SALES PRICE OF THE ENGINE. SELLER MAKES
NO WARRANTY AND DISCLAIMS ALL LIABILITY WITH RESPECT TO COMPONENTS OR PARTS
DAMAGED BY, OR WORN DUE TO, CORROSION.
(5) This warranty shall not apply to any engine or part thereof which has been repaired or altered outside
Lycoming’s factory in any way so as, in Lycoming’s sole judgment, to affect its durability, safety or reliability, or
which has been subject to misuse, negligence or accident. Repairs and alterations which use or incorporate parts and
components other than genuine Lycoming parts or parts approved by Lycoming for direct acquisition from sources
other than Lycoming itself are not warranted by Lycoming, and this warranty shall be void to the extent that such
repairs and alterations, in Lycoming’s sole judgment, affect the durability, safety or reliability of the engine or any
part thereof, or damage genuine Lycoming or Lycoming-approved parts. No person, corporation or organization,
including Distributors of Lycoming engines, is authorized by Lycoming to assume for it any other liability in
connection with the sale of its engines or parts, nor to make any warranties beyond the foregoing warranty nor to
change any of the terms hereof. NO STATEMENT, WHETHER WRITTEN OR ORAL, MADE BY ANY
PERSON, CORPORATION OR ORGANIZATION, INCLUDING DISTRIBUTORS OF LYCOMING ENGINES
MAY BE TAKEN AS A WARRANTY NOR WILL IT BIND LYCOMING. NO AGREEMENT VARYING THE
TERMS OF THIS WARRANTY OR LYCOMING’S OBLIGATIONS UNDER IT IS BINDING UPON
LYCOMING UNLESS IN WRITING AND SIGNED BY A DULY AUTHORIZED REPRESENTATIVE OF
LYCOMING.
(6) All legal actions based upon claims or disputes pertaining to or involving this warranty including, but not limited
to, Lycoming’s denial of any claim or portion thereof under this warranty, must be filed in the courts of general
jurisdiction of Lycoming County, Commonwealth of Pennsylvania or in the United States District Court for the
Middle District of Pennsylvania located in Williamsport, Pennsylvania. In the event that Purchaser files such an
action in either of the court systems identified above, and a final judgment in Lycoming’s favor is rendered by such
court, then Purchaser shall indemnify Lycoming for all costs, expenses and attorneys’ fee incurred by Lycoming in
defense of such claims. In the event Purchaser files such a legal action in a court other than those specified, and
Lycoming successfully obtains dismissal of that action or transfer thereof to the above described court systems, then
Purchaser shall indemnify Lycoming for all costs, expenses and attorneys’ fees incurred by Lycoming in obtaining
such dismissal or transfer.
(7) Any invalidity of a provision of this Warranty shall not affect any other provision, and in the event of a judicial
finding of such invalidity, this Agreement shall remain in force in all other respects.
Lycoming Engines
652 Oliver Street
Williamsport, Pennsylvania
17701
(570) 323-6181
www.lycoming.textron.com
TEXTRON LYCOMING OPERATOR'S MANUAL
TABLE OF CONTENTS
Page
1^
vii
TEXTRON LYCOMING OPERATOR'S MANUAL
viiI
TEXTRON LYCOMING OPERATOR'S MANUAL
DESCRIPTION Page
_* SECTION 1
DESCRIPTION
The VO-360 and IVO-360 series engines are four cylinder, vertical direct drive, horizontally opposed, wet
sump, air cooled helicopter engines.
When referring to the location of the various engine components, the parts are described in their
relationship to the engine as installed in the airframe. Thus, the power take-off end is considered the top and
the accessory drive end the bottom. The induction system and magnetos are considered aft and the opposite
side, where the shroud tubes are located, is considered forward. Reference to the left and right side of the
engine is made with the observer standing aft and facing forward. The cylinders are numbered from top to
bottom; odd numbers on the left, even numbers on the right. Rotation of the crankshaft is clockwise, viewed
from the bottom of the engine. Direction of rotation for accessory drives is determined with the observer
facing the drive pad.
Cylinders - The cylinders are of conventional air cooled construction with the two major parts, head and
barrel, screwed and shrunk together. The heads are made from an aluminum alloy casting with a fully
machined combustion chamber. Rocker shaft bearing supports are cast integral with the heads along with
housings to form the rocker boxes for both valve rockers. The cylinder barrels, which are machined from
chrome nickel molybdenum steel forgings, have deep integral cooling fins and the inside of the barrels are
ground and honed to a specified finish.
Valve Operating Mechanism - A conventional type camshaft is located forward of and parallel to the
crankshaft. The camshaft actuates hydraulic tappets which operate the valves through push rods and valve
rockers. The valve rockers are supported on full floating steel shafts. The valve springs bear against
hardened steel seats and are retained on the valve stems by means of split keys.
Crankcase - The crankcase assembly consists of two reinforced aluminum alloy castings, fastened together
by means of studs, bolts and nuts. The mating surfaces of the two castings are joined without the use of a
gasket, and the main bearing bores are machined for use of precision type main bearing inserts.
Crankshaft - The crankshaft is made from a chrome nickel molybdenum steel forging. All bearing journal
surfaces are nitrided.
Connecting Rods - The connecting rods are made in the form of "H" sections from alloy steel forgings.
They have replaceable bearing inserts in the crankshaft ends and bronze bushings in the piston ends. The
bearing caps on the crankshaft ends are retained by two bolts and nuts through each cap.
Pistons - The pistons are machined from aluminum alloy forgings. The piston pin is of a full floating type
with a plug located in each end of the pin. Depending on the cylinder assembly, pistons may be machined
for three or four piston rings and may employ either full wedge or half wedge rings. Consult the latest
revision of Service Instruction No. 1037 for proper piston and ring combinations.
1-1
SECTION 1 TEXTRON LYCOMING OPERATOR'S MANUAL
DESCRIPTION VO-360, IVO-360 SERIES
Accessory Housing and Oil Sump - Two aluminum castings provide housings for the accessory drives and
also form the sump. One casting fastens to the crankcase and houses the drives for the vacuum pump, fuel
pump and tachometer. This housing also forms three sides and bottom of the oil sump. The second casting,
referred to as the magneto case, mounts on the rear of the crankcase forming a crankcase cover and the
fourth side of the sump. This casting forms a housing for the magneto drives.
Cooling System - These engines are designed to be cooled by air pressure. The cooling air on rotor driven
aircraft is usually supplied by an external fan installed by the airframe manufacturer. Baffles are provided to
build up a pressure and force air through the cylinder fins. The discharge air is exhausted to the atmosphere
through suitably arranged openings.
Induction System - Textron Lycoming VO-360 series engines are equipped with a float type carburetor. See
Table 1 for model application. The carburetor is mounted on a fabricated steel distributing zone and the
fuel-air mixture is distributed to the cylinders by individual intake pipes.
Textron Lycoming IVO-360 series engines are equipped with a Precision Airmotive Corp. RSA type fuel
injector. See Table 1 for model application. The fuel injector schedules fuel flow in proportion to air flow
and fuel vaporization takes place at the intake port.
A brief description of the carburetor and fuel injector follows:
The Precision Airmotive Corp. MA-4-5 carburetor is of the single barrel float type and is equipped with a
manual mixture control and an idle cut-off. Model MA-4-5AA is basically the same as model MA-4-5
except that this unit incorporates an automatic mixture control.
The Precision Airmotive Corp. RSA type fuel injection system is based on the principle of measuring air
flow and using the air flow signal in a stem type regulator to convert the air force into a fuel force. This fuel
force (fuel pressure differential) when applied across the fuel metering section (jetting system) makes fuel
flow proportional to air flow.
Lubrication System - The full pressure wet sump lubrication system is actuated by an impeller type pump
contained within the accessory case.
Ignition System - Dual ignition is furnished by two Scintilla magnetos. See Table 1 for model application.
Priming System - Provision for a primer system is provided on all engines employing a carburetor. Fuel
injected engines do not require a primer system.
TABLE I
MODEL APPLICATION
Magnetos
Model Left Right Carburetor Fuel Injector
VO-360-A1A 4373 4373 MA-4-5 -------
VO-360-AIB S4LN-204 S4LN-200 MA-4-5AA -------
VO-360-B A S4LN-204 S4LN-200 MA-4-5AA --------
IVO-360-A1A S4LN-204 S4LN-200 RSA-5AD1
1-2
TEXTRON LYCOMING OPERATOR'S MANUAL
SPECIFICATIONS Page
SPECIFICATIONS
ALL MODELS
2-1
SECTION 2 TEXTRON LYCOMING OPERATOR'S MANUAL
SPECIFICATIONS VO-360, IVO-360 SERIES
DETAIL WEIGHTS
VO-360-A1A
VO-360-A1 B
2-2
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 2
VO-360, IVO-360 SERIES SPECIFICATIONS
VO-360-B1A
IVO-360-A1A
2-3
SECTION 2 TEXTRON LYCOMING OPERATOR'S MANUAL
SPECIFICATIONS VO-360, IVO-360 SERIES
DETAIL WEIGHTS
VO-360 SERIES
IVO-360 SERIES
VO-360 SERIES
IVO-360 SERIES
* - Formerly Prestolite.
2-4
TEXTRON LYCOMING OPERATOR'S MANUAL
SECTION 3
OPERATING INSTRUCTIONS
1. GENERAL. Close adherence to these instructions will greatly contribute to long life, economy, and
satisfactory operation of the engine.
NOTE
New engines have been carefully run-in at Textron Lycoming; however, cruising should be done at 65%
to 75% power until a total of 50 hours has accumulated or oil consumption has stabilized. This is to ensure
proper seating of the rings and is applicable to new engines, and engines in service following cylinder
replacement of top overhaul of one or more cylinders. (See latest revision of Service Instruction No. 1427.)
New or newly overhauled engines should be operated on a straight mineral oil for a minimum of 50 hours or
until oil consumption has stabilized. After this period, a change to an approved additive oil may be made, if
so desired. (See latest revision of Service Instruction No. 1014.)
The minimum fuel octane rating is listed in the flight chart, Part 8 of this section. Under no circumstances
should fuel of a lower octane rating or automotive fuel (regardless of octane rating) be used.
2. PRESTARTING ITEMS OF MAINTENANCE. Before starting the aircraft engine for the first flight of the
day, there are several items of maintenance inspection that should be performed. These are described in
Section 4 under Daily Pre-Flight Inspection. They must be observed before the engine is started.
3-1
SECTION 3 TEXTRON LYCOMING OPERATOR'S MANUAL
OPERATING INSTRUCTIONS VO-360, IVO-360 SERIES
(f) Prime engine by opening and closing throttle or with primer system if so equipped. Do not prime a hot
engine.
(h) When engine fires evenly, open throttle to an indicated speed of approximately 800 RPM.
(i) If oil pressure is not indicated within thirty seconds, stop engine and determine trouble.
(e) Turn on fuel boost pump (until there is a slight indication on gage).
(i) When engine fires, move mixture control smoothly to "full rich".
() If oil pressure is not indicated within thirty seconds, stop engine and determine trouble.
NOTE
Starting Flooded Engine - Set throttle in full open position. Set mixture control in full closed
position. Set magneto switch and boost pump off. Use starterto turn engine to clear cylinders
and induction system of fuel. Repeat startingprocedure but keep both throttle and mixture
controlsfully closed until engine starts.
5. COLD WEATHER STARTING. During extremely cold weather it may be necessary to preheat the engine
and oil before starting.
3-2
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 3
VO-360, IVO-360 SERIES OPERATING INSTRUCTIONS
(d) Leave carburetor heat control in "cold" position, unless ice forms in the induction system and heat is
necessary to clear the system.
(c) (Where Applicable.) Set carburetor heat in "hot" position to check for proper operation. Loss of RPM
and manifold pressure will result if control is working properly. Return to "cold" position.
(d) A proper magneto check is important. A magneto preflight test is useful to determine that both
magnetos are functioning properly and that no spark plug is misfiring. Additional factors, other than
the ignition system, affect drop-off. The important thing is that the engine runs smoothly because
magneto drop-off is affected by the variables listed above.
(e) Make the magneto check in accordance with the following procedure:
(1) Set engine to operate at 2850/2900 RPM and adjust manifold pressure to 15-16 inches Hg.
CA UTION
AVOID OPERATING IN THE 2500-2600 RPM RANGE ANY LONGER THAN NECESSARY.
(2) Switch from both magnetos to one and not drop-off, return to both until engine regains speed.
Switch to other magneto and note drop-off, return to both. Drop-off should not exceed 125 RPM
on either magneto. A smooth drop-off past normal is usually a sign of a too lean or too rich
mixture.
(3) Do not operate on a single magneto for too long a period, 2 to 3 seconds is usually sufficient to
note drop-off and will minimize plug fouling.
NOTE
Summer - Engine is warm enough for take-off when engine acceleration is smooth and the
oil temperature reaches a minimum of 100F.
Winter - In extremely cold weather it may be necessary to preheat the engine and oil before
starting.
(e) Limit ground running to minimum time necessary for correct manifold pressures for power
settings.
8. OPERATION IN FLIGHT.
(a) See airframe manufacturer's instructions for correct manifold pressures for power settings.
3-3
SECTION 3 TEXTRON LYCOMING OPERATOR'S MANUAL
OPERATING INSTRUCTIONS VO-360, IVO-360 SERIES
(b) Manual Mixture Control Leaning Procedure (Uncompensated Carburetor and Fuel Injector) -
Opinion varies among operators regarding manual leaning procedures to obtain most economical fuel-
air-ratios with a certain margin of safety. Improper fuel and oil mixtures take their toll in high
replacement parts in the form of cracked cylinder head, burned pistons, warped piston ring lands and
warped and failed valves. The procedures set forth in the latest revision of Textron Lycoming Service
Instruction No. 1094 have proven to be the most economical, both in low fuel consumption and low
parts replacement rates, and it is recommended that all Textron Lycoming operators adhere to these
procedures.
NOTE
For maximum engine life and reliability, it is recommended the cylinder head temperatures
for continuous cruise operationbe held to observed 400°F. or less.
(1) A more accurate method of determining the correct fuel-air ratio is a sensitive fast-responding
exhaust temperature indicator. Refer to latest revision of Textron Lycoming Service Instruction
No. 1094 for additional information on exhaust gas temperature gages.
CAUTION
1. NEVER OPERATE AN ENGINE ABOVE THE MAXIMUM CYLINDER HEAD
TEMPERA TURE SPECIFIED.
2. DO NOT INCREASE POWER FOR CLIMBING TO HIGHER ALTITUDES ABOVE 5000
FEET WITHOUT FIRST INCREASING ENGINE FUEL MIXTURE TO "FULL RICH".
READJUST ENGINE FUEL MIXTURE AFTER ATTAINING NEW ALTITUDE TO
DESIRED SETTING.
3. NEVER MANUALLY LEAN ENGINES EQUIPPED WITH ALTITUDE COMPENSATED
CARBURETORS OR FUEL INJECTORS.
(c) Use of CarburetorHeat Control- Under certain moist atmospheric conditions, it is possible for ice to
form in the induction system even in summer weather. This is due to the high air velocity through the
carburetor venturi and the absorption of heat from this air by evaporation of the fuel. The temperature
in the mixture chamber may drop 20°F. to 70°F. below the temperature of the incoming air. If this air
contains a large amount of moisture, the cooling process will cause precipitation in the form of ice.
These ice formations generally begin in the vicinity of the butterfly and will often build up to such an
extent that a drop in power output results. This loss of power is reflected by a drop in manifold
pressure and RPM. If not detected, this condition will continue to such an extent that the reduced
power will cause complete engine stoppage.
To avoid this condition, all installations are equipped with a system for preheating the incoming air
supply to the carburetor. In this way, sufficient heat is added to replace the heat loss to vaporization of
fuel, and the mixing chamber's temperature cannot drop to the freezing point of water. This air
preheater is essentially a tube or jacket through which the exhaust pipe from one or more cylinders is
passed, and the air flowing over these surfaces is raised to the required temperature before entering the
carburetor. Consistently high temperatures are to be avoided because of a loss in power and a decided
variation of the mixture. High charge temperatures also favor detonations and preignition, both of
which are to be avoided if normal service life is to be expected from the engine. The following outline
is the proper method of utilizing the carburetor heat control.
3-4
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 3
VO-360, IVO-360 SERIES OPERATING INSTRUCTIONS
(1) Take-Off- Take-off should be made with carburetor heat in full cold position. The possibility of
icing at wide throttle opening is very remote.
(2) Flight Operation - The carburetor air heat control should be left in the cold position during
normal flight operation. On damp, cloudy, foggy or hazy days, regardless of outside temperature,
keep a sharp lookout for loss of power. This loss of power will be shown by unaccountable loss in
manifold pressure and RPM. When this situation arises, apply full carburetor air heat and open the
throttle to limiting manifold pressure. This will result in a slight additional drop in manifold
pressure which is normal, and this drop will be regained as the ice is melted out of the induction
system. When the ice has been melted from the induction system the carburetor heat control
should be returned to the cold position. In those aircraft equipped with a carburetor air temperature
gage, partial heat may be used to keep the mixture temperature above the freezing point (32°F.).
WARNING
CAUTION MUST BE EXERCISED WHEN OPERATING WITH PARTIAL HEAT ON
AIRCRAFT THAT DO NOT HAVE A CARBURETOR AIR TEMPERATURE GAGE.
MOISTURE IN CRYSTAL FORM THAT WOULD ORDINARILY PASS THROUGH THE
INDUCTION SYSTEM, CAN BE RAISED IN TEMPERATURE BY USE OF PARTIAL HEAT
TO THE POINT WHERE THE CRYSTALS ARE MELTED INTO LIQUID FORM THIS
MOISTURE CAN FORM CARBURETOR ICE DUE TO THE TEMPERATURE DROP AS IT
PASSES THROUGH THE VENTURI OF THE CARBURETOR. IT IS ADVISABLE,
THEREFORE, TO USE EITHER FULL HEAT OR NO HEAT IN AIRCRAFT THAT ARE
NOT EQUIPPEDWITHA CARBURETOR AIR TEMPERATURE GAGE.
(3) Landing Approach - In making an approach for a landing, carburetor air heat should not be used
unless icing conditions exist. If carburetor heat is applied during descent and emergency power
should be needed, it is possible that detonation might occur resulting in a further loss of power
under critical conditions. See aircraft flight manual for specific instructions.
9. ENGINE FLIGHTCHART.
Fuel ......................................... Aviation Grade Fuel 91/96 octane minimum
Oil -
Average *Recommended Grade Oil
Ambient Air Single Viscosity Multi Viscosity
Above 60°F. SAE 50 40 or 50
30° to 90°F. SAE 40 40
0° to 70°F. SAE 30 40 or 20W-30
Below 10°F. SAE 20 20W-30
* - Refer to latest revision of Service Instruction No. 1014.
Oil Sump Capacity ................................... ..................... 6 U. S. Quarts
Minimum Safe Quantity of Oil in Sump ........................................ 1-1/2 U.S. Quarts
It is recommended that the lubricating oil be changed every fifty flying hours.
3-5
SECTION 3 TEXTRON LYCOMING OPERATOR'S MANUAL
OPERATING INSTRUCTIONS VO-360, IVO-360 SERIES
OPERATING CONDITIONS
3-6
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 3
VO-360, IVO-360 SERIES OPERATING INSTRUCTIONS
.70
I
.65
PART THROTTLE SPEC.
FUEL CONSUMPTION
-1
.60
0
.55
.50
3-7
SECTION 3 TEXTRON LYCOMING OPERATOR'S MANUAL
OPERATING INSTRUCTIONS VO-360, IVO-360 SERIES
z
3
Figure 3-2. Sea Level and Altitude Performance Curve - VO-360-A1A
3-8
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 3
VO-360, IVO-360 SERIES OPERATING INSTRUCTIONS
ALTITUDE COMPENSATION
2900 R.P.M. FULL THROTTLE
.55 I
\^~~^^ 'LB/BHP/HR
.50
.45
11
.65 \
.55
.50
80 100 120 140 160 180
BRAKE HORSEPOWER
3-9
SECTION 3 TEXTRON LYCOMING OPERATOR'S MANUAL
OPERATING INSTRUCTIONS VO-360, IVO-360 SERIES
r
-----------
Figure 3-4. Sea Level and Altitude Performance Curve - VO-360-A1B, -B1A
3-10
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 3
VO-360, IVO-360 SERIES OPERATING INSTRUCTIONS
111
HIGH LIMIT
10
,L FLOW ,
9
8
LOW LIMIT
, 7
0
NOZZLE PRESSURE PSIG
3-11
SECTION 3 TEXTRON LYCOMING OPERATOR'S MANUAL
OPERATING INSTRUCTIONS VO-360, IVO-360 SERIES
CURVE NU.12921
--- 110
90
80
70
60
50
40
50 60 70
80 90 100
PERCENT NORMAL RATED POWER
3-12
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 3
VO-360, IVO-360 SERIES OPERATING INSTRUCTIONS
.N
- - --
1_
-
-
a
NeZ
Figure 3-7. Sea Level and Altitude Performance Curve - IVO-360-A1A
3-13
TEXTRON LYCOMING OPERATOR'S MANUAL
SECTION 4
PERIODIC INSPECTIONS
NOTE
Perhapsno other factor is quite so important to safety and durability of the aircraft and its
components as faithful and diligent attention to regular checks for minor troubles and
prompt repairwhen they arefound.
The operator should bear in mind that the items listed in the following pages do not constitute a complete
aircraft inspection, but are meant for the engine only. Consult the airframe manufacturer's handbook for
additional instructions.
Pre-StartingInspection - The daily pre-flight inspection is a check of the aircraft prior to the first flight of
the day. This inspection is to determine the general condition of the aircraft and engine.
The importance of proper pre-flight inspection cannot be over emphasized. Statistics prove several
hundred accidents occur yearly directly responsible to poor pre-flight.
Among the major causes of poor pre-flight inspection are lack of concentration, reluctance to
acknowledge the need for a check list, carelessness bred by familiarity and haste.
4-1
SECTION 4 TEXTRON LYCOMING OPERATOR'S MANUAL
PERIODIC INSPECTIONS VO-360, IVO-360 SERIES
1. DAILY PRE-FLIGHT
2. 25-HOUR INSPECTION. After the first twenty-five (25) hours of operating time, new, remanufactured or
newly overhauled engines should undergo a 50-hour inspection including draining and renewing lubricating
oil. Change oil every 25 hours. Also, inspect and clean the oil suction and pressure screens.
3. 50-HOUR INSPECTION. In addition to the items listed for daily pre-flight inspection, the following
maintenance checks should be made after every 50 hours of operation.
(a) Ignition System -
(1) Remove spark plugs; test, clean and regap. Replace if necessary.
(2) Examine spark plug leads of cable and ceramics for corrosion and deposits. This condition is
evidence of either leaking spark plugs or improper cleaning of the spark plug walls or connector
ends. Where this condition is found, clean the cable ends, spark plug walls and ceramics with a
dry, clean cloth or a clean cloth moistened with methyl-ethyl ketone. All parts should be clean and
dry before reassembly.
(3) Examine ignition harness for security of mounting clamps and be sure connections are tight at
spark plug and magneto terminals.
(b) Fuel and Induction System -
(1) Check primer lines for leaks and security of clamps. Drain carburetor or fuel injector and clean
fuel strainer. Check mixture control and throttle linkage for travel, freedom of movement and
security of clamps; lubricate if necessary.
(2) Check induction air intake ducts for leaks, security, filter damage; evidence of dust or other solid
material in the ducts is indicative of inadequate filter care or damaged filter. Check vent lines for ^
evidence of fuel or oil seepage; if present, fuel pump may require replacement.
4-2
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 4
VO-360, IVO-360 SERIES PERIODIC INSPECTIONS
(c) LubricationSystem -
(1) Check oil lines for leaks, particularly at connections for security of anchorage, for wear due to
rubbing or vibration and for dents and cracks.
(2) Drain and refill sump with new oil. See the latest revision of Service Instruction No. 1014 for
recommended lubricating oils. Seasonal grades are listed in Section 3, Item 8, of this manual.
(3) Remove oil suction and oil pressure screens and clean thoroughly as described in Section 5, Item 3
of this manual. Note carefully for presence of metal particles that are indicative of internal engine
damage. Change oil every 25 hours.
(4) If engine is equipped with external oil filters, service in accordance with filter manufacturer's
instructions.
(d) Exhaust System - Check attaching flanges at exhaust ports on cylinders for evidence of leakage. If
they are loose they must be removed and machined flat before they are reassembled and tightened.
Examine exhaust manifolds for general condition.
(e) Cooling System - Check cowling for damage and secure anchorage. Any damaged or missing part of
the cooling system must be repaired or replaced before the aircraft resumes operation.
(f) Cylinders -
(1) Check rocker box covers for evidence of oil leaks. If found, replace gasket and tighten screws to
specified torque (50 in. Ibs.).
(2) Check cylinders for evidence of excessive heat which is indicated by burned paint on the cylinder.
This condition is indicative of internal damage to the cylinder, and if found, its cause must be
determined and corrected before the aircraft resumes operation.
(3) Heavy discoloration and appearance of seepage at cylinder head and barrel attachment area is
usually due to emission of thread lubricant used during assembly of the barrel at the factory orby
slight gas leakage which stops after the cylinder has been in service for awhile. This conditions
neither harmful nor detrimental to engine performance and operation. If it can be proven that
leakage exceeds these conditions, the cylinder should be replaced.
(g) Carburetor - Check throttle body attaching screws for tightness. The correct torque for these screws
is 40 to 50 inch pounds.
4. 100-HOUR INSPECTION. In addition to the items listed for daily pre-flight and 50-hour inspection, the
following maintenance checks should be made after every 100 hours of operation.
(a) ElectricalSystem -
(I) Check all wiring connected to the engine or accessories. Any shielded cables that are damaged
should be replaced. Replace faulty clamps or loose wires and check terminals for security and
cleanliness.
4-3
SECTION 4 TEXTRON LYCOMING OPERATOR'S MANUAL
PERIODIC INSPECTIONS VO-360, IVO-360 SERIES
(2) Remove spark plugs; test, clean and regap. Replace if necessary.
(c) Magnetos - Check breaker points for pitting and minimum gap. Check for excessive oil in the breaker
compartment; if found, wipe dry with a clean lintless cloth. The felt located at the breaker points
should be lubricated in accordance with the magneto manufacturer's instructions. Check magneto-to-
engine timing. Timing procedure is described in Section 5, 1. b. of this manual.
(d) Engine Accessories - Engine mounted accessories such as pumps and temperature and pressure
sensing units should be checked for secure mounting, tight connections and terminals.
(f) Engine Mounts - Check engine mounting bolts and bushings for security and excessive wear. Replace
any bushings that are excessively worn.
(g) Fuel Injection Nozzles and Fuel Lines - Check fuel injector nozzles for looseness; tighten to 60 inch
pounds torque. Check fuel line connection for dye stains indicating leakage and security of line.
Repair or replace before the aircraft resumes operation.
5. 400-HOUR INSPECTION. In addition to the items listed for daily pre-flight, 50-hour and 100-hour
inspections, the following maintenance check should be made after every 400 hours of operation.
Valve Inspection - Remove rocker box covers and check for freedom of valve rockers when valves are
closed. Look for evidence of abnormal wear or broken parts in the area of the valve tips, valve keeper,
springs and spring seats. If any indications are found, the cylinder and all of its components should be
removed (including the piston and connecting rod assembly) and inspected for further damage. Replace any
parts that do not conform with limits shown in the latest revision of Special Service Publication No.
SSP1776.
4-4
TEXTRON LYCOMING OPERATOR'S MANUAL
Ignition System
Fuel System
Lubrication System
Cylinder Assembly
SECTION 5
MAINTENANCE PROCEDURES
The procedures in this section are intended to guide and instruct personnel in performing maintenance
operations that may be required in conjunction with the periodic inspections listed in the preceding section.
No attempt is made to include repair and replacement operations that will be found in the applicable Textron
Lycoming Overhaul Manual.
(a) Ignition Harness and Wire Replacement - In the event that an ignition harness or an individual lead is
to be replaced, consult the wiring diagram to be sure harness is correctly installed. Mark location of
clamps and clips to be certain the replacement is clamped at correct location.
(b) Timing Magnetos to Engine - Although several combinations of magnetos are used in this series
engines, (see Table of Models, Section 1, for model application) the timing procedures in the
following paragraphs are the same for all magnetos.
NOTE
Either the impulse coupling or retard breaker magneto (whichever is applicable) is installed
on the right side of the engine.
(1) Remove a spark plug from No. 1 cylinder and place a thumb over the spark plug hole. Rotate the
crankshaft in direction of normal rotation until the compression stroke is reached, this is indicated
by a positive pressure inside the cylinder tending to push the thumb off the spark plug hole.
Continue rotating the crankshaft in direction of normal rotation until the advance timing mark of
the top face of the starter ring gear is in exact alignment with the small hole located at the two
o'clock position on the front face of the starter housing. At this point, the engine is ready for
assembly of the magnetos.
NOTE
If the crankshaft is accidentally turned in the direction opposite normal rotation, repeat the
above procedure as accumulated backlash will make the final timing incorrect.
(2) Remove the inspection plugs from both magnetos and turn the drive shafts in direction of normal
rotation until the first painted chamfered tooth on the distributor gear is aligned in the center of the
inspection window. Being sure that the gear does not move from this position, install gaskets and
magnetos on the engine. Secure with washers and nuts; tighten only finger tight.
NOTE
In order to turn the shaft on an impulse coupling magneto, depress the pawl on the impulse
coupling with the finger.
5-1
SECTION 5 TEXTRON LYCOMING OPERATOR'S MANUAL
MAINTENANCE PROCEDURES VO-360, IVO-360 SERIES
I r
1 -I
3
FIRING ORDER
1-2-3-4 4
2 REAR
( 4 REAR
5-2
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 5
VO-360, IVO-360 SERIES MAINTENANCE PROCEDURES
(3) Using a battery powered timing light, attach the positive lead to a suitable terminal connected to
the ground terminal of the magneto and the negative lead to any unpainted portion of the engine.
Rotate the magneto in its mounting flange to a point where the light comes on, then slowly turn it
in the opposite direction until the light goes out. Bring the magneto back slowly until the light just
comes on. Repeat this with the second magneto.
NOTE
AC timing lights operate in the reverse manner as described above, the light goes out when
the breakerpoints open.
(4) After both magnetos have been timed, check, as described below, to ascertain that both magnetos
are set to fire simultaneously.
(5) Back off the crankshaft a few degrees from 25° BTC, the timing light should go out. Bring the
crankshaft slowly back in direction of normal rotation until the timing mark and the hole in the
starter housing are in alignment. At this point, both lights should go on simultaneously. Tighten
nuts to specified torque.
(c) Generator or Alternator Output - The generator or alternator (whichever is applicable) should be
checked to determine that the specified voltage and current are being obtained.
2. FUEL SYSTEM.
(a) Repair of Fuel Leaks - In the event a line or fitting in the fuel system is replaced, only a fuel soluble
lubricant (such as clean engine oil or Loctite Hydraulic Sealant) may be used sparingly on the tapered
threads. Any other thread lubricant or compound must not be used. Do not apply the sealant to the
first two threads.
(b) Carburetoror Fuel Injector Inlet Screen Assembly - Remove the assembly and check the screen for
distortion or openings in the strainer. Replace for either of these conditions. Clean screen assembly in
solvent and dry with compressed air. To install the screen assembly, place the gasket on the screen
assembly and install the assembly in the throttle body and tighten to 35-40 inch pounds torque.
(c) Fuel Grades and Limitations - Subject engines are designed to operate on 91/96 octane (minimum)
aviation grade fuel. In the event that the specified fuel is not available at some locations, it is
permissible to use higher octane fuel. Fuel of a lower octane than specified is not to be used. Under no
circumstances should automotive fuel be used (regardless of octane rating).
NOTE
It is recommended that personnel be familiar with the latest revision of Service Instruction
No. 1070 regardingspecifiedfuelfor Textron Lycoming engines.
(d) Air Intake Ducts and Filter - Check all air intake ducts for dirt or restrictions. Inspect and service air
filters as instructed in the airframe manufacturer's handbook.
5-3
SECTION 5 TEXTRON LYCOMING OPERATOR'S MANUAL
MAINTENANCE PROCEDURES VO-360, IVO-360 SERIES
5-4
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 5
VO-360, IVO-360 SERIES MAINTENANCE PROCEDURES
(2) Remove rocker box drain tube, intake pipe, baffle and any clips that might interfere with the
removal of the cylinder.
(3) Disconnect ignition cables and remove the bottom spark plug.
(4) Remove rocker box cover and rotate crankshaft until piston is approximately at top center of the
compression stroke. This is indicated by a positive pressure inside of cylinder tending to push
thumb off of bottom spark plug hole.
(5) Slide valve rocker shafts from cylinder head and remove the valve rockers. Valve rocker shafts
can be removed from the engine. Remove rotator cap from exhaust valve stem.
(6) Remove push rods by grasping ball end and pulling rod out of shroud tube. Detach shroud tube
spring and lock plate and push shroud tubes through holes in cylinder head.
NOTE
The hydraulic tappets, push rods, rocker arms and valves must be assembled in the same
locationfrom which they were removed
(7) Remove cylinder base nuts and hold down plugs (where employed) then remove cylinder by
pulling directly away from crankcase. Be careful not to allow the piston to drop against the
crankcase as the piston leaves the cylinder.
(b) Removal of Piston from Connecting Rod - Remove the piston pin plugs. Insert piston pin puller
through piston pin, assemble puller nut; the proceed to remove piston pin. Do not allow connecting
rod to rest on the cylinder pad of the crankcase. Support the connecting rod with heavy bands,
discarded cylinder base oil ring seals or any other non-marring method.
(c) Removal of Hydraulic Tappet Sockets and Plunger Assemblies - It will be necessary to remove and
bleed the hydraulic tappet plunger assemblies so that dry tappet clearance can be checked when the
cylinder assembly is reinstalled. This is accomplished in the following manner: A special Textron
Lycoming tool is available for removal of the sockets and plunger assemblies. In the event the tool is
not available, proceed as described below.
(1) Remove the hydraulic tappet push rod socket by inserting the forefinger into the concave end of
the socket and withdrawing. If the socket cannot be removed in this manner, it may be removed by
grasping the edge of the socket with a pair of needle nose pliers. However, care must be exercised
to avoid scratching the socket.
(2) To remove the hydraulic tappet plunger assembly, use the special Textron Lycoming service tool.
In the event that the tool is not available, the hydraulic tappet plunger assembly may be removed
by a hook in the end of a short piece of lockwire, inserting the wire so that the hook engages the
spring of the plungers assembly. Draw the plunger assembly out of the tappet body by gently
pulling the wire.
5-5
SECTION 5 TEXTRON LYCOMING OPERATOR'S MANUAL
MAINTENANCE PROCEDURES VO-360, IVO-360 SERIES
CA UTION
(d) Assembly of Hydraulic Tappet Plunger Assemblies - To assemble the unit, unseat the ball by inserting
a thin clean bronze wire through the oil inlet hole. With the ball off its seat, insert the plunger and
twist clockwise so that the spring catches. All oil must be removed before the plunger is inserted.
(e) Assembly of Cylinder and Related Parts - Rotate the crankshaft so that the connecting rod of the
cylinder being assembled is at top center of compression stroke. This can be checked by placing two
fingers on the intake and exhaust tappet bodies. Rock crankshaft back and forth over top center. If the
tappet bodies do not move the crankshaft is on the compression stroke.
(1) Place each hydraulic tappet plunger assembly in its respective body and assemble socket on top of
plunger assembly.
(2) Assemble piston with rings so that the cylinder number stamped on the piston pin boss is toward
the top of the engine. The piston pin should be a push fit. If difficulty is experienced in inserting
the piston pin, it is probably caused by carbon or burrs in the piston pin hole. During assembly,
always use a generous amount of oil, both in the piston pin hole and on the piston pin.
(3) Assemble one piston pin plug at each end of the piston pin and place a new cylinder base oil seal
ring around the cylinder skirt. Coat piston, rings and the inside of the cylinder generously with oil.
S
(4) Using a piston ring compressor, assemble the cylinder over the piston so that the intake and
exhaust ports are toward the rear of the engine.
NOTE
At any time a cylinder is replaced, it is necessary to retorque the thru-studs on the cylinder
on the opposite side of the engine.
(5) Push the cylinder down onto the cylinder mounting studs.
NOTE
Before installing cylinder hold down nuts, lubricate crankcase thru-stud threads with any
one of the following lubricants, or combination of lubricants.
(6) Assemble hold down plates and cylinder base hold down nuts and tighten as directed in the
following steps:
5-6
TEXTRON LYCOMING OPERATOR'S MANUAL SECTON 5
VO-360, IVO-360 SERIES MAINTENANCE PROCEDURES
NOTE
At any time a cylinder is replaced, it is necessary to retorque the thru-studs on the cylinder
on the opposite side of the engines.
a) Install shims between cylinder base hold down plates and cylinder barrel, as directed in Figure
5-2, and tighten 1/2 inch hold down nuts to 300 inch pounds (25 foot pounds) torque, using the
sequence shown in Figure 5-2.
b) Remove shims, and using the same sequence, tighten the 1/2 inch cylinder base nuts to 600
inch pounds (50 foot pounds) torque.
c) Tighten the 3/8 inch hold down nuts to 300 inch pounds (25 foot pounds) torque. Sequence of
tightening is optional.
d) As a final check, hold the torque wrench on each nut for about five seconds. If the nut does not
turn, it may be presumed to be tightened to the correct torque.
CAUTION
AFTER ALL CYLINDER BASE NUTS HAVE BEEN TIGHTENED, REMOVE ANY NICKS
ON THE CYLINDER FINS BY FILING OR BURRING.
(7) Insert a new shroud tube oil seal over each end of the shroud tube.
(8) Install each shroud tube through the rocker box and seat the end firmly in the crankcase. Place a
spacer, two springs, a lockplate and nut over the stud provided in the rocker box and secure both
shroud tubes in place. Bend the tang of the lockplate to prevent the nut and spring from loosening.
(9) Assemble each push rod in its respective shroud tube, install rotator cap on exhaust valve stem and
assemble each rocker in its respective position by placing rockers between bosses and sliding
valve rocker shaft in place to retain rockers.
(10) Be sure that the piston is at top center compression stroke and that both valves are closed. Check
clearance between the valve stem tip and the valve rocker. In order to check this clearance, place
the thumb of one hand on the valve rocker directly over the end of the push rod and push down so
as to compress the hydraulic tappet spring. While holding the spring compressed, check valve
clearance, which should be between .028 and .080 inch. If the clearance does not come within
these limits, remove the push rod and insert a longer or shorter push rod, as required to correct
clearance.
(11) Install gaskets and rocker box covers, intake pipes, drain tubes and exhaust manifold. Install spark
plugs, ignition harness and exhaust valve oil line tube.
(12) After removal and replacement of one or more cylinders, consult the latest revision of Service
Instruction No. 1427 for proper run-in.
5-7
SECTION 5 TEXTRON LYCOMING OPERATOR'S MANUAL
MAINTENANCE PROCEDURES VO-360, IVO-360 SERIES
5. GENERATOR OR ALTERNATOR DRIVE BELT TENSION ,Check the tension of a new belt 25 hours
after installation. Refer to latest revision of Service Instruction No. 1129 and latest revision of Service Letter
No. L 160 for methods of checking generator or alternator belt tension.
HIM
REQ'D PER CYLINDER
010 IN tHICK X .50/.70 IN. WIDE)
1
HORIZONTAL CENTER
LINE OF ENGINE
VIDE)
Figure 5-2. Location of Shims Between Cylinder Barrel and Hold Down Plates and
Sequence of Tightening Cylinder Base Hold Down Nuts
5-8
TEXRON LYCOMING OPERATOR'S MANUAL
TROUBLE-SHOOTING Page
SECTION 6
TROUBLE-SHOOTING
General - Experience has proven the best method of "trouble-shooting" is to decide on the various possible
causes of a given trouble and then to eliminate these causes one by one, beginning with the most probable.
The following chart lists some of the more common engine trouble usually found in maintaining aircraft
engines.
Failure of Engine to Start Lack of fuel Check fuel system for leaks.
Fill fuel tank. Clean dirty lines,
strainers or fuel cocks.
Failure of Engine to Idle Properly Incorrect idle adjustment Adjust throttle stop to obtain
correct idle.
6-1
SECTION 6 TEXTRON LYCOMING OPERATOR'S MANUAL
TROUBLE-SHOOTING VO-360, IVO-360 SERIES
TROUBLE
CAUSE REMEDY
Failure of Engine to Idle Properly Low cylinder compression Check condition of piston rings
(Cont.) and valve seats.
Low Power and Uneven Running Mixture too rich; indicated by Check primer shut-off valve for
sluggish engine operation, red leakage. Readjustment of carb-
exhaust flame at night. Extreme uretor or fuel injector by author-
cases indicated by black smoke ized personnel is indicated.
from exhaust.
Mixture too lean; indicated by Check fuel lines and filters for
overheating or backfiring dirt or other restrictions. Re-
adjustment of carburetor or fuel
injector by authorized personnel
is indicated.
Failure of Engine to Develop Throttle lever out of adjustment Adjust throttle lever.
Full Power
6-2
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 6
VO-360, IVO-360 SERIES TROUBLE-SHOOTING
Failure of Engine to Develop Restriction in carburetor air scoop Examine air scoop and remove
Full Power (Cont.) restrictions. Clean air filter.
Low Oil Pressure Insufficient oil Fill sump to proper level with
oil of recommended grade.
Air lock or dirt in relief valve Remove and clean oil pressure
relief valve.
High Oil Temperature Insufficient air cooling Check air inlet and outlet for
deformation or obstruction.
6-3
SECTION 6 TEXTRON LYCOMING OPERATOR'S MANUAL
TROUBLE-SHOOTING VO-360, IVO-360 SERIES
Excessive Oil Consumption Low grade of oil Fill tank with oil conforming to
specification.
Engine Does Not Stop Linkage does not permit full Readjust linkage for full travel.
travel of "Idle Cut-Off'
6-4
TEXTRON LYCOMING OPERATOR'S MANUAL
Duration............................................................... 7-2
SECTION 7
Preparationof Engine for Installation - Before installing an engine that has been prepared for storage,
remove all dehydrator plugs, bags of dessicant and preservative oil from the engine. Preservative oil can be
removed by removing the bottom spark plugs and turning the crankshaft three or four revolutions by hand.
The preservative oil will then drain through the spark plug holes. Draining will be facilitated if the engine is
tilted from side to side during the above operation. Preservative oil which has accumulated in the sump can
be drained by removing the oil sump plug. Engines that have been stored in a cold place should be removed
to an environment of at least 70°F. (21°C.) for a period of 24 hours before preservative oil is drained from
the cylinders. If this is not possible, heat the cylinders with heat lamps before attempting to drain the engine.
Should any of the dehydrator plugs, containing crystals of silica-gel or similar material, be broken during
their term of storage or upon their removal from the engine, and if any of the contents should fall into the
engine, that portion of the engine must be disassembled and thoroughly cleaned before using the engine.
The oil strainers should be removed and cleaned in an approved hydrocarbon solvent. The fuel drain screen
located in the fuel inlet of the carburetor should also be removed and cleaned in a hydrocarbon solvent.
After the oil sump has been drained, the plug should be replaced, safety-wired and the sump refilled with
lubricating oil. The crankshaft should again be turned several revolutions to saturate the interior of the
engine with the clean oil. When installing spark plugs, make sure that they are clean, if not, wash them in
clean petroleum solvent. Of course, there will be a small amount of preservative oil remaining in the engine,
but this can cause no harm. After twenty-five hours of operation, the lubricating oil should be drained while
the engine is hot. This will remove any residual preservative oil that may have been present.
CA UTION
Inspection of Engine Mounting - If the aircraft is one from which an engine has been removed, make sure
that the engine mount is not bent or damaged by distortion or misalignment as this can produce abnormal
stresses with the engine.
Attaching Engine to Mounts - See airframe manufacturer's recommendations for method of mounting the
engine.
Engine Accessories - Considerable time and effort can be saved if the accessories are installed on the engine
before the engine is mounted in the airframe. The locations of the various accessories and drives on the
engine are called out on the accompanying installation drawings.
7-1
SECTION 7 TEXTRON LYCOMING OPERATOR'S MANUAL
INSTALLATION AND STORAGE VO-360, IVO-360 SERIES
Oil and Fuel .ine Connections - The oil and fuel line connections
are called out
connections are on the accompanying
the
called accompanying
out on
installation drawings.
Preparationof Enginefor Storage - The following procedure is intended for application to installed engines
which are being removed from aircraft, and will provide protection from corrosion for a period of 30 to 60
days.
PreservationRun - Immediately prior to removal of the engine from the aircraft, the engine should be given
a preservation run under the following operating conditions.
Oil - Fill sump to normal capacity with preservative type lubricating oil.
Durationof Run - Operate the engine for a period of four minutes, holding the engine speed to a maximum
of 1800 RPM. All precautions pertaining to ground running should be carefully observed. Cylinder head,
ignition harness and magneto temperatures should not be allowed to exceed the prescribed limits.
Compound Injection - Upon completion of the preservation run, drain the preservative oil from the engine
and remove, clean and replace the oil suction and oil pressure screens. Perform any engine checks, such as
valve clearance or ignition timing, which require rotation of the crankshaft. Disconnect the ignition harness
and remove the spark plugs. Starting with cylinder no. 1, make certain piston is at the bottom of
compression stroke. Fill cylinder with preservative oil (use same oil as specified for preservation run) and
rotate crankshaft until piston is at top center. Oil will spill out of spark plug hole. In order to preserve the
top wall of the cylinder, it will be necessary to either rock the engine, or blow compressed air with very light
pressure into the spark plug hole. Following the engine firing order, preserve the remainder of the cylinders
in the same manner. When all cylinders have been treated, then spray the exhaust port and valve of each
cylinder with the piston 1/4 turn before top center of the exhaust stroke. When absolutely certain that no
further need exists for turning the crankshaft, again spray each cylinder through the spark plug holes.
(Maintain spray nozzle temperature at 200°F. to 220°F. (93°C. to 104°C.) for all spraying operations.)
Installation of Seals and Plugs - Install cylinder dehydrator plugs (Textron Lycoming P/N 40238 or
equivalent) in spark plug holes. Install ignition cable protectors (Textron Lycoming P/N 40239 or
equivalent) over the spark terminal of each ignition cable and secure by attaching to the end of the
dehydrator plug. Flush all accessory drives for which oil seals are provided with preservative oil before
assembling the drive covers. Suitable covers (Textron Lycoming P/N 74156 or equivalent) should be used in
sealing the exhaust ports; moisture resistant tape (Minnesota Mining and Manufacturing Company, 711
Acetate Fibre Tape or equivalent) will be sufficient for the ground connections and similar openings. Install
a plug (Textron Lycoming P/N 1540 or equivalent) in the thermometer well at the rear of the oil pressure
screen housing. Install sealing caps (Textron Lycoming P/N 61596 or equivalent) over the breather opening
and generator blast tube. Install tachometer drive cap (Textron Lycoming P/N 61545 or equivalent) over
tachometer drive. Make sure all other openings are properly sealed.
Exterior Surfaces - All exposed cadmium plated and machined surfaces should be coated with soft film
corrosion-preventative compound (E.F. Houghton and Company, Cosmoline 1059 or equivalent). The
starter ring gear in particular should receive a liberal coating of the compound.
7-2
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 7
VO-360, IVO-360 SERIES INSTALLATION AND STORAGE
Carburetor- Drain all residual gasoline from the carburetor, fill with flushing oil and flush the interior
surfaces by rocking the carburetor. After flushing, drain the carburetor, replace all plugs, lock the throttle in
the closed position and pack the carburetor in a cardboard carton.
Fuel Injector - Any unit taken out of service, or units being returned for overhaul, must be flushed with
preserving oil (Specification MIL-0-6081, Grade 1010), using the following procedure.
(a) Remove plugs and drain all fuel from the injector. If available, apply 10 to 15 psi air pressure to the
fuel inlet, until all fuel is discharged from the injector.
(b) Replace plugs and apply flushing oil filtered through a 10 micron filter at 13 to 15 psi to the fuel inlet
until oil is discharged from the servo line.
CA UTION
(d) After filling with preservative oil, the injector should be protected from dust and dirt, and given such
protection against moisture as climatic conditions at the point of storage required. In most cases,
storing the unit in a dry area will be sufficient.
~(e) If the unit is to be stored near or shipped over salt water, the following precautions should be
observed.
(1) Spray the exterior of the injector with an approved preservative oil, Socony "Avrex 901" or
equivalent.
(2) Pack in a sealed dust proof container, wrap the container with moisture and vapor proof material,
and seal. Pack the wrapped unit in a suitable shipping case. Pack a one-half pound bag of silica-
gel crystals in the dust proof container with the injector. The bag must not touch the injector.
CA UTION
7-3
SECTION 7 TEXTRON LYCOMING OPERATOR'S MANUAL
INSTALLATION AND STORAGE VO-360, IVO-360 SERIES
Shipping Case - Upon completion of the preceding steps, the engine should be secured in a suitable engine
shipping container. The date of preservation and the following legend should be legibly marked on the side
of the container:
"On (Date)__ the engine was preserved for 60 days short term storage with the
preservative oil and cylinder and crankcase dehydratorplugs. The dehydratorplugs shall be
inspected on arrivalat destination or 30 days after the above date (whichever occurs sooner)
to determine if renewal of the dehydrating agent is necessary."
Recommended Procedures for Preservation - The engine shall be examined every 30 days (or less,
depending on weather and locality). If any evidence of corrosion is present, the affected area should be
cleaned free of corrosion and the engine represerved.
Engines prepared in the preceding manner are not adequately protected for extended periods of storage. If
at the end of 60 days it is found that the engine must remain in storage for an additional period, the engine
must be represerved according to the foregoing procedure.
NOTE
Inspection and represervationwill not be the responsibility of the engine manufacturer after
engines have been shipped from the engine manufacturer's plant. It shall be the
responsibility of the consignee to put engine into service in the order of storage preparation
date to reduce the storageperiod to a minimum.
7-4
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 7
VO-360, IVO-360 SERIES INSTALLATION AND STORAGE
/
~~~~\
LD PRESS
PRIMING LINE
CONNECTION
CENTER OF
GRAVITY
PRIMER
IL PRESS
-REEN
7-5
SECTION 7 TEXTRON LYCOMING OPERATOR'S MANUAL
INSTALLATION AND STORAGE VO-360, IVO-360 SERIES
STARTER DRIVE n
.ER TUBE
EL GAGE
/ALVE
7-6
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 7
VO-360, IVO-360 SERIES INSTALLATION AND STORAGE
7-7
TEXTRON LYCOMING OPERATOR'S MANUAL
TABLES Page
SECTION 8
TABLES
CONSULT THE LATEST REVISION OF SERVICE INSTRUCTION NO. 1029 AND NO.
1150 FOR INFORMATION PERTINENT TO CORRECTLY INSTALLING CYLINDER
ASSEMBLY.
8-1
SECTION 8 TEXTRON LYCOMING OPERATOR'S MANUAL
TABLES VO-360, IVO-360 SERIES
8-2
TEXTRON LYCOMING OPERATOR'S MANUAL SECTION 8
VO-360, IVO-360 SERIES TABLES
S^~~
^CENTIGRADE-FAHRENHEIT CONVERSION TABLE
Example: To convert 15°C. to Fahrenheit, find 15 in the center column headed (F-C); then read 59.0°F. in
the column (F) to the right. To convert 15°F. to Centigrade; find 15 in the center column and read -9.44°C.
in the (C) column to the left.
C FC F C FC F
8-3
SECTION 8 TEXTRON LYCOMING OPERATOR'S MANUAL
TABLES VO-360, IVO-360 SERIES
8-4