17

CI/SfB: n5
Dec 2012

Fosroc® Supercast SW constructive solutions

Swellable waterstops for in-situ concrete Supercast SWX also enables Supercast SW sections to be
linked into conventional Supercast PVC waterstop networks.
Uses This allows the use of Supercast PVC for expansion joints
and Supercast SW for construction joints whilst maintaining
Integral sealing for construction joints in concrete cast an integrated waterproofing network.
in-situ.
Convenient and problem solving in situations where a Design criteria
conventional waterstop would require complex shuttering. Supercast SW should be used to prevent the passage of water
Typical uses include secant piled and diaphragm walled through non-movement joints in both new in-situ concrete and
basements, pile caps and casting against old concrete. The between new and existing concrete. Supercast SW increases
Supercast SW range can provide simple solutions to detailing in volume up to a maximum of 200% and gives resistance to
pipe entries, construction joints in the vertical plane and to hydraulic pressure.
kicker joints. Swelling of Supercast SW in fresh concrete is minimal
They can be linked to Supercast PVC waterstops to give an therefore maximising the positive pressure seal provided by
appropriate effective combination of waterstops which maintain the hydrophilic to the protected joint.
network continuity. Supercast SW20 has a larger section and so offers a greater
surface area of contact to the concrete in areas of higher risk,
Advantages such as when waterproofing Grade 3 basements.
 Easy to install by adhesive bonding, or casting into joint Both Supercast SW10 and SW20 have a delayed swell action
faces which helps prevent pre-swell during wet site conditions (see
 Supercast SWX enables full integration of Supercast SW limitations).
and Supercast PVC networks
The minimum thickness of concrete cover required to
 Supercast SW Adhesive and Supercast SWX can be accommodate pressure developed during the swelling process
applied to damp substrates is 75mm for Supercast SW10 and 80mm for SW20.
 Solves detailing problems in conjunction with Supercast
PVC waterstops Standard compliance
 Swelling properties unaffected by long term wet/dry cycling
Supercast SW10 and Supercast SW20 are suitable for use in
 Tolerant of salts in concrete and groundwater contact with potable water and are Water Regulations Advisory
 Sustains effective seal in wet conditions Service approved products.
 Highly adaptable to accommodate complex joint shapes Drinking Water Inspectorate Regulation 25(1)b of the Water
Supply (Water Quality) Regulations 1989.
Description
The Supercast SW range consists of swellable waterstops; Specification clauses
Supercast SW formed sections, Supercast SWX gun-applied Supercast SW
paste and Supercast SW Adhesive.
Water swellable polymeric hydrophilic waterstops (and
Supercast SW sections are made from high performance attachments) where shown on the drawings, shall be Fosroc
synthetic elastomer strips. The swelling action of the Supercast Supercast SW10 (or SW20) obtained from Fosroc Limited,
SW range is the result of contact between water and hydrophilic Drayton Manor Business Park, Coleshill Road, Tamworth,
groups which are an intimate part of the Supercast SW Staffs. B78 3TL. It shall be used in accordance with the
polymeric structure. These hydrophilic groups are not subject manufacturer’s current application instructions.
to extraction and loss of swelling performance by prolonged
or repeated wetting.
Expansion of the waterstop creates a positive pressure against
the faces of the concrete joint, thus preventing water passing
through the joint.
Supercast SWX is a grey, elastomeric water-swellable gun
applied paste. Supercast SWX can be used as a swellable
adhesive to adhere Supercast SW waterstop to concrete. It
has the capability to fill undulations and surface holes in the
concrete beneath the waterstop and swell into these when
required.

Page 1
 17
CI/SfB: n5
Dec 2012

Fosroc® Supercast SW

Water swellable polymeric hydrophilic waterstop where shown

on the drawings, shall be made from a preformed elastomeric
strip which can integrate into existing waterstop networks. It
shall be free from rubber, bentonite or other inclusions. The
Supercast SW
waterstop shall have an unrestrained volumetric expansion of waterstop
up to 300%. It must not deteriorate under prolonged wet/dry
cycling. It must be able to withstand a hydrostatic head of up to
50 metres (refer SW grade). It shall be used in accordance with
the methods given in the manufacturer’s current data sheet.
Properties

Form: Rectangular section

elastomeric strips
Size:
Supercast SW10: 5 mm x 20 mm
Supercast SW20: 10 mm x 20 mm
Solids content: 100%
Colour:
Supercast SW10: Black
Supercast SW20: Red Pile cap detail using Supercast SW waterstop
Unrestrained volumetric
expansion ratio: Up to 200%
Application temperature
range: –5°C to 50°C
Service temperature
range: –30°C to 70°C Secant piled Supercast SWX
wall gunned between
Hydrostatic pressure SW10: 30 metres bulbs to form
resistance*: SW20: 50 metres seal
Supercast SW
*(In concrete construction joint with no movement) waterstop
Unrestrained volume swell

Supercast
Rearguard
waterstop

Dry Supercast SW, Supercast SWX and Supercast Rearguard

Number of wet/dry cycles
0 10 20 30
waterstops at secant pile wall and floor slab junction

Graphic showing reproducibility of volume swell with

wet/dry cycling

constructive solutions
Page 2
 17
CI/SfB: n5
Dec 2012

Fosroc® Supercast SW

Application instructions SW Details with 2 cages of reinforcement

Supercast SW may be positioned by bonding with Supercast
SWX or Supercast SW Adhesive. The waterstop may be
installed either into a suitable groove cast in the concrete or
directly onto the concrete surface.

80
Estimating
Pack sizes
Supercast SW10: 5 mm x 20 mm x 15 metre
 Minimum wall height above
rolls kicker is 1m
Supercast SW20 : 10 mm x 20 mm x 5 metre  Minimum wall thickness
rolls 190mm with SW 10
200mm with SW20
Supercast SWX: 310 ml cartridge packed in SW20 80mm min.
SW10 75mm min.
cartons of 20, or as a single SW20 80mm min.
 Minimum concrete cover to SW
75mm with SW10
SW10 75mm min.
tube 80mm with SW20

Supercast SW Adhesive: 380 ml cartridge packed in Note:

cartons of 20 assuming 20mm diameter rebar.

Coverage

Supercast Usually single run of strip per

SW10 /SW20: joint
Supercast SWX: 6 mm diameter bead
(per cartridge) - 11 metres run
12mm diameter bead SW Details with 1 cage of reinforcement placed
- 2.7 metres run centrally
Supercast SW Adhesive: 6 mm diameter bead
(per cartridge) - 13.5 metres run
12 mm diameter
- 3.4 metres run
80

The above coverages are approximate and make no

allowances for wastage.

Limitations
Supercast SW should not be used for expansion joints or
those subject to movements in excess of 2mm.
SW20 80mm min.
Supercast SW swell rate is dependent on the quality (solids SW10 75mm min.
content) of water and the temperature of water. The lower SW20 80mm min.
SW10 75mm min.
the temperature and the greater the solids content, the lower
the swell rate.
Supercast SW should not be used in locations which allow
free unrestrained swelling or for free standing walls, such as
bund or dwarf walls, where the swell pressure is sufficient to
lift the wall from its foundations. Contact Fosroc for product/
method recommendations in this case.
Supercast SW may be fixed with Supercast SW Adhesive on
smooth surfaces, but Supercast SWX Adhesive should be used
where concrete is rough. In both instances the bead diameter
of the adhesive should be a minimum of 12mm.
Supercast SW must not be immersed in water prior to concrete
placement, however, Supercast SW20 can tolerate upto 3

constructive solutions Page 3

 17
CI/SfB: n5
Dec 2012

Fosroc® Supercast SW

Storage Precautions
Supercast SW Health and safety
Shelf life: 12 months
Supercast SW
Store in original unopened cartons or bags in
cool, dry conditions, away from sunlight. There are no known health hazards associated with
Supercast SW10 and SW20 in normal use.
Supercast SWX
Shelf life: 9 months Supercast SWX
Store in original unopened cartridges or cartons
Supercast SWX may cause sensitisation by skin contact.
in cool, dry conditions, away from sunlight
Avoid contact with skin and eyes. Wear suitable gloves and
Supercast SW Adhesive eye/face protection. Use only in well ventilated areas.
Shelf life: 12 months Supercast SW Adhesive
Store in original unopened cartridges or cartons
in cool, dry conditions, away from sunlight No significant hazard. For additional information see
relevant product safety data sheet.
Additional information

Ancillary materials

Supercast SWX
Form: Elastomeric water
swellable paste
Colour: Grey
Tack-free time: Approximately 1 hour
(20°C / 50% RH)
Cure rate: 3mm in 24 hours
Volume swell ratio: 200%
Concrete pour: 2 to 8 hours

Supercast SW Adhesive
Form: Grey paste
Application temperature: 5°C to 30°C
Maximum open time: 30 minutes
Concrete pour: 2 to 8 hours
Adhesion: Can be used on damp concrete provided it is
rag dry.
The above data represents typical values and should not
be considered as a purchase specification.

Fosroc and Supercast are trademarks of

Fosroc International Limited

Important note
Fosroc products are guaranteed against defective materials and manufacture and are sold subject to its standard Conditions for the
Supply of Goods and Services, copies of which may be obtained on request. Whilst Fosroc endeavours to ensure that any advice, recom-
mendation, specification of information it may give is accurate and correct, it cannot, because it has no direct or continuous control over
where or how its products are applied, accept any liability either directly or indirectly arising from the use of its products, whether or not in
accordance with any advice, specification, recommendation of information given by it.

Fosroc Limited
constructivesolutions
constructive solutions
telephone: Aydinevler Mah.
fax: Telephone:
email: E-mail:
Fosroc Idea
Drayton Manor Business Park,
Coleshill Road, Tamworth, +44 0 (1827) 262222 +44 0 (1827)
Sanayi Cad. Demirtas 262444
Plaza +90 216 463 69 63 enquiryturkey@fosroc.com
enquiryuk@fosroc.com
Construction
Staffordshire B78 3TL. UK No: 13 D: 7-8, 34854, Fax:
Chemicals Co.
www.fosroc.com
Maltepe – Istanbul / TURKEY +90 216 463 67 76 www.fosroc.com
Certificate number FM 610

Page 4