Pin Cylinders

CJP2/CJP Series
ø4, ø6, ø10, ø15, ø16

2 auto switches can even be mounted on a cylinder CJ1

with ø4 bore size (5 mm stroke). CJP

CJ2
One-touch fitting can be connected. JCM
(Panel mount type)
ø2 One-touch fitting, miniature
fitting, and speed controller
CM2
can be connected.
CM3
Auto switch CG1
CG3
ø2 One-touch fitting
JMB
Double acting / CJP2 Series Single acting / CJP Series MB
MB1
CA2
CS1
CS2

D-
-X
Technical
Data
21
 Small and Light
Double acting / CJP2 Series
A
 Full
 length: Shortened
Full length: 6 toto 9.5 mm
Shortened by
by mm
Weight: Reduced
 Weight:
 by 55 to
Reduced by to 65% %

C
New aluminum body is light weight compared
with the current CJP series.
(Compared with the basic model CJP cylinder without auto switch)
(CDJP2B4-10D)
B
Dimensions Unit: mm Weight Unit: g
Bore size A B C Bore size (mm)
Stroke
29 + stroke 4 6 10 16
4 14 14.5 5 11 16 27 42
(34 + stroke)
10 13 18 29 46
6 33 + stroke
14 16.5 15 15 21 32 50
(38 + stroke)
20 17 23 35 54
10 39.5 + stroke 15 19 25 — 25 37 58
(44.5 + stroke) 30 — — 40 63
16 43.5 + stroke 35 — — 43 67
20 24.5
(48.5 + stroke) 40 — — 45 71
∗( ): Dimension for built-in magnet type

Single acting / CJP Series

Panel mount type (CJPB4-5) Embedded type (CJPS4-5)

le ::1
SSccaale
00%% le ::1
SSccaale
00%%
B

C A C A

Dimensions Unit: mm Weight Unit: g

A Stroke Bore size (mm)
Bore size B C
5st 10st 15st (mm) 4 6 10 15
4 23.5 31.5 39.5 10 11.5 5 10 10.6 28 75
6 27.5 34.5 41.5 12 13.9 10 13 13.1 33 82
10 32.5 39 46 19 22 15 15 15.6 38 92
15 37.5 43.5 50 27 31

Variation
Series Action Bore size (mm) Standard stroke (mm) Mounting Note 2) Series Action Bore size (mm) Standard stroke (mm) Mounting
Double 4 5, 10, 15 (20) Note 1) Basic Single 4 5, 10, 15 Panel mount
acting, 6 5, 10, 15, 20, 25 Flange acting, 6 5, 10, 15 type,
CJP2 Foot CJP Spring
Single 10 5, 10, 15, 20, 25, 30, 35, 40 Clevis 10 5, 10, 15 Embedded
rod 16 5, 10, 15, 20, 25, 30, 35, 40 Trunnion return 15 5, 10, 15 type
Note 1) A stroke of 20 is available with a standard product only. Note 2) Bore size of ø4 is available with basic mounting only.

Related Products
Refer to Best Pneumatics No. 7.

ø2 Speed Controller
AS Series

ø2 Miniature Fittings
M Series

ø2 One-touch Fittings ø2 Polyurethane Tubing

TU Series

22
 Pin Cylinder: Double Acting, Single Rod

CJP2 Series
ø4, ø6, ø10, ø16
CJ1
How to Order CJP
CJ2
Standard CJP2 F 10 15 D JCM
Built-in magnet CDJP2 F 10 15 D M9BW S CM2

With auto switch Made to Order CM3

(Built-in magnet) (Refer to page 24.)
CG1
Mounting
Symbol Mounting Standard
Built-in Number of auto switches CG3
magnet
Nil 2 pcs.
B Basic
S 1 pc.
F Flange JMB
L Foot
D Clevis Auto switch MB
T Trunnion Nil Without auto switch
∗ Bore size of 4 mm is available with basic mounting
only.
∗ For the applicable auto switch MB1
model, refer to the below table.
∗ Mounting bracket is shipped together (but not
assembled).
∗ Trunnion mounting type is shipped after Bore size
CA2
assembled.
4 4 mm
6 6 mm Rod end thread CS1
10 10 mm Nil With thread
16 16 mm B Without thread CS2
Built-in Magnet Cylinder Model
Cylinder standard stroke (mm) Double acting
If a built-in magnet cylinder without an auto
ø4 5, 10, 15, (20) Note)
switch is required, there is no need to
ø6 5, 10, 15, 20, 25
enter the symbol for the auto switch.
ø10, ø16 5, 10, 15, 20, 25, 30, 35, 40
(Example) CDJP2B6-20
Note) A stroke of 20 is available with a standard product only.

Applicable Auto Switches / For detailed auto switch specifications, refer to page 1575 through to 1701.
Load voltage Auto switch model Lead wire length (m)∗
Indicator

Special Electrical
Type

Pre-wired
light

Wiring (Output) Electrical entry direction 0.5 1 3 5 connector Applicable load

function entry DC AC
Perpendicular In-line (Nil) (M) (L) (Z)
3-wire (NPN) M9NV M9N IC
5 V, 12 V circuit
M9PV M9P
Solid state auto switch

— 3-wire (PNP)
2-wire 12 V M9BV M9B —
Diagnostic 3-wire (NPN) M9NWV M9NW IC
5 V, 12 V Relay,
indication Grommet Yes 3-wire (PNP) 24 V — M9PWV M9PW circuit
PLC
(2-color) 2-wire 12 V M9BWV M9BW —
Water 3-wire (NPN) M9NAV∗1 M9NA∗1 IC
resistant 5 V, 12 V
(2-color
3-wire (PNP) M9PAV∗1 M9PA∗1 circuit
indicator) 2-wire 12 V M9BAV∗1 M9BA∗1 —
3-wire (NPN equiv.) — 5V — A96V∗∗ A96∗∗ — — — IC circuit —
auto switch

Yes
Reed

— Grommet 12 V 100 V A93V∗∗

∗2 A93∗∗ — — Relay,
2-wire 24 V
No 5 V, 12 V 100 V or less A90V∗∗ A90∗∗ — — — IC circuit PLC
∗1 Water resistant type auto switches can be mounted on the above models, but in such case SMC cannot guarantee water resistance.
Consult with SMC regarding water resistant types with the above model numbers.
∗2 1 m type lead wire is only applicable to D-A93.
∗ Lead wire length symbols: 0.5 m ······ Nil (Example) M9NW ∗∗ The D-A9(V) switch is not attachable to ø4. D-
1 m ······ M M9NWM
3 m ······ L
5 m ······ Z
M9NWL
M9NWZ -X
∗ Auto switches marked with “” are made to order specification.
∗ For details about auto switches with pre-wired connector, refer to pages 1648 and 1649. Technical
∗ Auto switches are shipped together, (but not assembled). Data
23
CJP2 Series

Specifications

Action Double acting, Single rod

Maximum operating pressure 0.7 MPa

Minimum ø4 0.15 MPa

operating ø6 0.12 MPa
pressure
ø10, ø16 0.06 MPa
Proof pressure 1 MPa
Ambient and fluid Without auto switch: –10 to 70°C
temperature With auto switch: –10 to 60°C (No freezing)
Lubrication Not required (Non-lube)
+1.0
Stroke length tolerance 0
Rod end type With thread/Without thread
Piston speed 10 to 500 mm/s∗
Symbol Cushion Rubber bumper
Double acting, Single rod, Rubber bumper
Mounting Note) Basic, Flange, Foot, Clevis, Trunnion
Note) Bore size of ø4 is available with basic mounting only. The piston speed for a bore size of ø4 is 50 to 500 mm/s.

Standard Equipment Accessory Standard Stroke

Made to Order: Accessory Mounting Rod end Bore size

Individual Specifications nut (2 pcs.) Trunnion Stroke (mm)
nut (with (mm)
(with pin)
(For details, refer to page 33.) Mounting (1 pc.) thread)
4 5, 10, 15, 20 Note)
Symbol Specifications Basic
-X1666 Interchangeability of clevis and trunnion types 6 5, 10, 15, 20, 25
Flange
10 5, 10, 15, 20, 25, 30, 35, 40
Made to Order Foot
(For details, refer to pages 1703 to 1896.) 16 5, 10, 15, 20, 25, 30, 35, 40
Clevis
Symbol Specifications ∗ 20 stroke of bore size 4 mm is standard type only.
Trunnion
-XA Change of rod end type
-XB6 Heat resistant cylinder (150°C)
-XB7 Cold resistant cylinder Option Mounting Bracket Part No.
-XC22 Fluororubber seals
Bore size Bore size
(mm) 6 10 16 (mm) 6 10 16
Theoretical Output Description Bracket
Auto switch D-A9(V), D-M9(V), D-M9W(V) Flange CP-F006A CP-F010A CP-F016A
(N)
Single Foot CP-L006A CP-L010A CP-L016A
I-P006A I-P010A I-P016A
Bore size Operating Operating pressure (MPa) knuckle joint
(mm) direction Trunnion
0.3 0.5 0.7 Double CP-T006A CP-T010A CP-T016A
(with pin)
IN 2.8 4.7 6.6 knuckle joint Y-P006A Y-P010A Y-P016A
4 (with pin)
OUT 3.8 6.3 8.8
∗ Refer to page 30 for dimensions.
IN 6.4 10.6 14.8
6
OUT 8.5 14.1 19.8
Weight
IN 19.8 33.0 46.2 (g)
10
OUT 23.6 39.3 55.0 Stroke (mm) Bore size (mm)
IN 51.8 86.4 121.0 Mounting 4 6 10 16
16
OUT 60.3 100.5 140.7 5 11 16 27 42
10 13 18 29 46
OUT
IN 15 15 21 32 50
Basic weight

20 17 23 35 54
Moisture 25 — 25 37 58
Control Tube 30 — — 40 63
IDK Series
35 — — 43 67
When operating an actuator with a small diameter
and a short stroke at a high frequency, the dew 40 — — 45 71
condensation (water droplet) may occur inside the Flange — 5 6 16
Bracket weight

piping depending on the conditions.

Foot — 7 9 24
Simply connecting the moisture control tube to the
actuator will prevent dew condensation from oc- Clevis — 2 5 8
curring. For details, refer to the IDK series in the Trunnion (with pin) — 15 25 70
Best Pneumatics No. 6.
Additional weight for built-in magnet 2 3 5 7

24
 Pin Cylinder: Double Acting, Single Rod CJP2 Series

Allowable Kinetic Energy

Caution
When driving an inertial load, operate a cylinder with kinetic energy within the allowable value. The range in the
chart below that is delineated by bold solid lines indicates the relation between load mass and maximum driving
speeds. CJ1
Bore size (mm) 4 6 10 16 CJP
Piston speed (m/s) 0.05 to 0.5
Allowable kinetic energy (J) 0.75 x 10-2 1.2 x 10-2 2.5 x 10-2 5.0 x 10-2 CJ2
10.00
JCM
ø16
CM2
ø10 CM3
CG1
Load mass (kg)

1.00
ø6
CG3
ø4
JMB
MB
0.10
MB1
100 CA2
Maximum speed (mm/s)

CS1
Allowable Lateral Load CS2
Strictly observe the limiting range of lateral load on a piston rod. (Refer to the below graph.) If this product is used
beyond the limits, it may shorten the machine life or cause damage.
Allowable lateral load

1
Allowable lateral load (N)

0.8
ø16

0.6

0.4
ø10

0.2
ø6
ø4 D-
0
0 5 10 15 20 25 30 35 40 45
-X
Stroke (mm)
Technical
Data
25
CJP2 Series

Construction
CJP2B4 CJP2B6

i r u q w Built-in magnet
i e u q Built-in magnet

t y !1 o !0 !2 !4 !5 !1 o r !0 !2 w t !4 !5

CJP2B10, 16
i e u q Built-in magnet

!1 o r !0 !3 !2 t w !5 !4

Replacement Parts: Seal Kit

Component Parts Standard
No. Description Material Note Bore size (mm) Kit no. Contents
1 Body Aluminum alloy Hard anodized 6 CJP2B6D-PS
ø4, ø6, ø10 Brass Electroless nickel plated 10 CJP2B10D-PS Set of left nos. !0, !1, !2.
2 Head cover
ø16 Aluminum alloy Chromated 16 CJP2B16D-PS
3 Piston rod Stainless steel ∗ Seal kit includes a grease pack (5 g).
ø4 Stainless steel Order with the following part number when only the grease pack is needed.
Grease pack part number: GR-L-005 (5 g)
4 Piston ø6, ø10 Brass
ø16 Aluminum alloy Chromated XB6/Heat-resistant cylinder (–10 to 150°C)
5 Retaining ring Tool steel Phosphate coating Bore size (mm) Kit no. Contents
6 Seal retainer Special steel Nickel plated 6 CJP2B6D-XB6-PS
7 Mounting nut Brass Electroless nickel plated 10 CJP2B10D-XB6-PS Set of left nos. !0, !1, !2.
8 Rod end nut Steel Zinc chromated 16 CJP2B16D-XB6-PS
9 Bumper Urethane rubber ∗ Seal kit includes a grease pack (5 g).
10 Piston seal NBR Order with the following part number when only the grease pack is needed.
Grease pack part number: GR-F-005 (5 g)
11 Rod seal NBR
ø4 Stainless steel + NBR XB7/Cold-resistant cylinder
12 Gasket
ø6, ø10, ø16 NBR Bore size (mm) Kit no. Contents
13 Piston gasket NBR 6 CJP2B6D-XB7-PS
14 Magnet — 10 CJP2B10D-XB7-PS Set of left nos. !0, !1, !2.
ø4, ø6, ø10 Brass 16 CJP2B16D-XB7-PS
15 Magnet retainer
ø16 Aluminum alloy Chromated ∗ Seal kit includes a grease pack (5 g).
Order with the following part number when only the grease pack is needed.
Grease pack part number: GR-T-005 (5 g)

XC22/Fluororubber seal
Bore size (mm) Kit no. Contents
6 CJP2B6D-XC22-PS
10 CJP2B10D-XC22-PS Set of left nos. !0, !1, !2.
16 CJP2B16D-XC22-PS
∗ Seal kit includes a grease pack (5 g).
Order with the following part number when only the grease pack is needed.
Grease pack part number: GR-L-005 (5 g)

26
 Pin Cylinder: Double Acting, Single Rod CJP2 Series

Dimensions: Basic Mounting (ø4)

Standard: CJP2B4

29 + Stroke
14 12.5 + Stroke 2.5
CJ1
7 7 4.5 4.5
Mounting nut 6 6 2 x M3 x 0.5 CJP
Width across flats 10
7
Rod end nut CJ2
Width across flats 4
JCM

ø1.7

ø2
14.5

CM2
5

30°

CM3
2

M2 x 0.4
C

Without rod end thread

14 M8 x 1.0 3
CG1
CG3
JMB
Built-in magnet: CDJP2B4
MB
34 + Stroke MB1
14 17.5 + Stroke 2.5
7 7 4.5 4.5 CA2
Mounting nut 6 6 2 x M3 x 0.5
Width across flats 10 CS1
7
Rod end nut
Width across flats 4
CS2
ø1.7

ø2
14.5
5

30°

M2 x 0.4
C2

Without rod end thread

14 M8 x 1.0 3

D-
-X
Technical
Data
27
CJP2 Series

Dimensions: Basic Mounting (ø6 to ø16)

Standard: CJP2B6 to 16

Z + Stroke
H S + Stroke
A' F GA GB
Mounting nut A F' 2xP
Width across flats B1
A'
Rod end nut
Width across flats B2 30°

øD-1
øD
E
J

MM Without rod end thread

C

B NN W

(mm)
Symbol
A A' B B1 B2 C D E F F' GA GB H J MM NN P S W Z
Bore size
6 7 9 14 14 5.5 2 3 16.5 8 6.5 5.5 6.5 17 6 M3 x 0.5 M10 x 1.0 M3 x 0.5 16 3 33
10 10 12 15 17 7 2.5 4 19 8 6.5 6 7 20 7 M4 x 0.7 M12 x 1.0 M3 x 0.5 19.5 3 39.5
16 12 14 20 19 8 3 6 24.5 10 8.5 6.5 7.5 24 10 M5 x 0.8 M14 x 1.0 M5 x 0.8 19.5 4 43.5

Built-in magnet: CDJP2B6 to 16

Z + Stroke
H S + Stroke
A' F GA GB
Mounting nut A F' 2xP
Width across flats B1
A'
Rod end nut
Width across flats B2 30°
øD-1
øD
E
J

MM
C

Without rod end thread

B NN W

(mm)
Symbol
A A' B B1 B2 C D E F F' GA GB H J MM NN P S W Z
Bore size
6 7 9 14 14 5.5 2 3 16.5 8 6.5 5.5 6.5 17 6 M3 x 0.5 M10 x 1.0 M3 x 0.5 21 3 38
10 10 12 15 17 7 2.5 4 19 8 6.5 6 7 20 7 M4 x 0.7 M12 x 1.0 M3 x 0.5 24.5 3 44.5
16 12 14 20 19 8 3 6 24.5 10 8.5 6.5 7.5 24 10 M5 x 0.8 M14 x 1.0 M5 x 0.8 24.5 4 48.5

28
 Pin Cylinder: Double Acting, Single Rod CJP2 Series

Mounting Bracket Dimensions

Flange: C(D)JP2F6 to 16
Flange Flange (mm)
Symbol
FC FT FW FX FY FZ
Bore size
CJ1
FW

6 3.4 1.6 18.5 24 16 32

FY

10 4.5 1.6 21 28 18 37

2 x øFC FT 16 5.5 2.3 25.5 36 22 49 CJP

FX
∗ Other dimensions are the same as basic mounting.
FZ CJ2
JCM
Foot: C(D)JP2L6 to 16 CM2
LX Foot (mm)
øL
C
Symbol
CM3
2x X Y LC LH LT LW LX LZ
Bore size
CG1
Y

6 6.5 10.5 3.4 11 1.6 21.5 20 28

X

10 7 12 4.5 13 1.6 25 24 33

Foot
16 10 16.5 5.5 18 2.3 32.5 30 43 CG3
∗ Other dimensions are the same as basic mounting.
LW

JMB
LH

MB
LT

LZ

MB1
Clevis: C(D)JP2D6 to 16 CA2
ZZ + Stroke Clevis (mm) CS1
S + Stroke Symbol
CD CK GB Q
GB Bore size
6 3 +0.040 4 11.5 —
CS2
Q 0
10 5 +0.065 6.5 18 0
17 –0.5
øCD with flange bushing 0
16 +0.065
6 0 10 22 0
22 –0.5
(None for ø6)
Symbol S Z ZZ
Without Built-in Without Built-in Without Built-in
Bore size magnet magnet magnet magnet magnet magnet

Z + Stroke CK 6 21 26 34 39 38 43
10 30.5 35.5 44 49 50.5 55.5
16 34 39 48 53 58 63

Trunnion: C(D)JP2T6 to 16 Rotation angle

ZZ + Stroke CT
Pin hole dia. øCD
2 x øCY
CU

C-type retaining ring

Trunnion ≈A
CH

°
CX 20

Q Z + Stroke CK ≈B
Mounting dimensions of
trunnion bracket T CZ

Trunnion (mm)
Symbol Z ZZ Applicable bore ø6 ø10 ø16 D-
CD CH CK CT CU CX CY CZ Q T Without Built-in Without Built-in ≈A 54° 62° 55°
-X
Bore size magnet magnet magnet magnet ≈B 110° 110° 102°
6 3 16 4 12 1.6 18 3.4 26 18.5 20.4 34 39 38 43 ∗ Provided as guidelines.
10 5 20 6.5 13.5 1.6 24 4.5 33 20.5 23.9 44 49 50.5 55.5 The values are varied depending on the condition. Technical
16 6 25 10 15 2.9 29 5.5 42 28 31.7 48 53 58 63 Data
29
 CJP2 Series
Accessory Bracket Dimensions
Single knuckle joint Double knuckle joint
øND hole H10
Axis d9

Material: Rolled steel ∗ Knuckle pin and retaining ring are included. Material: Rolled steel
Applicable Applicable
Part no. bore size A B L1 L2 MM NDH10 NX R1 R2 U Part no. bore size A B L L1 L2 MM NDd9 NDH10 NX R1 R2 U
(mm) (mm)
I-P006A 6 5 6 12 3.5 M3 x 0.5 3+0.040
0 3 5 4 5 Y-P006A 6 5 6 9 12 3.5 M3 x 0.5 3–0.020
–0.045 3+0.040
0 3 5 4 5
I-P010A 10 6.5 10 16 5.5 M4 x 0.7 5+0.048
0 5 8 6.3 7 Y-P010A 10 6.5 10 13.6 16 5.5 M4 x 0.7 5–0.030
–0.060 5+0.048
0 5 8 6.3 7
I-P016A 16 7 12 19 7 M5 x 0.8 6 +0.048
0 6 10 7.8 9 Y-P016A 16 7 12 15.8 19 7 M5 x 0.8 6–0.030
–0.060 6+0.048
0 6 10 7.8 9

Knuckle pin Trunnion pin

L1 L1

Material: Stainless steel Material: Stainless steel

Applicable Applicable
Retaining∗ Retaining∗
Part no. bore size D d9 L d L1 m t ring
Part no. bore size D d9 L d L1 m t ring
(mm) (mm)
IY-P006 6 3 –0.020
–0.045 9 2.85 6.2 0.75 0.65 Clip C-type 3 CT-P006 6 3–0.020
–0.045 20.4 2.85 17.6 0.75 0.65 Clip C-type 3
IY-P010 10 5–0.030
–0.060 13.6 4.8 10.2 1 0.7 C-type 5 CT-P010 10 5–0.030
–0.060 23.9 4.8 20.5 1 0.7 C-type 5
IY-P015 16 6 –0.030
–0.060 15.8 5.7 12.2 1 0.8 C-type 6 CT-P015 16 6–0.030
–0.060 31.7 5.7 28.1 1 0.8 C-type 6
∗ Included ∗ Included

Mounting nut Rod end cap

Flat type: CJ-CF
A MM
øD
5

Material: Brass N
0.
C

Part no. Applicable bore size (mm) d H B C W

SNPS-004 4 M8 x 1.0 3 10 11.5 L
SNP-006 6 M10 x 1.0 3 14 16.2
SNP-010 10 M12 x 1.0 3 17 19.6
Round type: CJ-CR
SNP-015 16 M14 x 1.0 4 19 21.9

A MM
Rod end nut
øD

RR

N
W
L

Material: Polyacetal
Material: Iron Part no. Applicable
bore size A D L MM N RR W
Part no. Applicable bore size (mm) d H B C Flat type Round type (mm)
NTJ-004 4 M2 x 0.4 1.6 4 4.6 CJ-CF004 CJ-CR004 4 5 6 9 M2 x 0.4 3 6 5
NTP-006 6 M3 x 0.5 1.8 5.5 6.4 CJ-CF006 CJ-CR006 6 6 8 11 M3 x 0.5 5 8 6
NTP-010 10 M4 x 0.7 2.4 7 8.1 CJ-CF010 CJ-CR010 10 8 10 13 M4 x 0.7 6 10 8
NTP-015 16 M5 x 0.8 3.2 8 9.2 CJ-CF016 CJ-CR016 16 10 12 15 M5 x 0.8 7 12 10
30
 CJP2 Series
Auto Switch Mounting 1
Auto Switch Proper Mounting Position (Detection at Stroke End) and Its Mounting Height
D-A9(V), D-M9(V), D-M9W(V), D-M9A(V)
B CJ1
CJP
CJ2
≈ H3

≈ H2
JCM
A
≈ H1
CM2
CM3
Applicable Auto Switches: D-A9, D-A9V (mm)
A
Bore size (When detecting at extended
B (When detecting at retracted stroke end position)
H1 H2 H3 CG1
stroke end position) 5 st 10 st 15 st 20 st 25 st 30 st 35 st 40 st
ø4 — — — — — — — — — — — — CG3
ø6 1 6 11 16 21 26 — — — 13 10 20
ø10 1 6 11 16 21 26 31 36 41 16 9.5 19 JMB
ø16 1 6 11 16 21 26 31 36 41 18 12 24
MB
Applicable Auto Switches: D-M9, D-M9V, D-M9W, D-M9WV, D-M9A, D-M9AV (mm)
A B (When detecting at retracted stroke end position) MB1
Bore size (When detecting at extended H1 H2 H3
5 st 10 st 15 st 20 st 25 st 30 st 35 st 40 st
ø4
stroke end position)
4 9 14 19 — — — — — 14.5 11.5 23
CA2
ø6 5 10 15 20 25 30 — — — 15 11.5 23
ø10 5 10 15 20 25 30 35 40 45 18 10.5 21
CS1
ø16 5 10 15 20 25 30 35 40 45 20 13 26
Note) Only adjust the setting position after confirming the auto switch is properly activated.
CS2
W

Mounting: Basic, Flange, Foot (mm)

Auto switch
model D-M9 D-M9V D-A96 D-A90
D-M9A D-M9AV
D-M9W D-M9WV D-A9V D-A93
Bore size W
ø4 6 4 8 6 — —
ø6 6 4 8 6 2 4.5
ø10 2.5 0.5 4.5 2.5 0 1
ø16 2.5 0.5 4.5 2.5 0 1

Mounting: Clevis, Trunnion (mm)

Auto switch D-M9V
model
D-M9 D-M9WV
D-M9A D-M9AV
D-M9W D-A9
D-A9V
Bore size W
ø4 — — — — D-
ø6 1 0 3 2
ø10 0 0 2 2 -X
ø16 0 0 2 2
∗ 0 (zero) denotes the auto switch does not protrude from the end surface. Technical
Note) Adjust the auto switch after confirming the operating conditions in the actual setting. Data
31
 CJP2 Series
Auto Switch Mounting 2
Operating Range Minimum Stroke for Auto Switch Mounting
(mm) (mm)
Bore size Applicable auto switch model
Auto switch model
4 6 10 16 No. of auto D-M9W, D-M9WV
D-A9(V) — 5 6 7 switches mounted D-M9, D-M9V D-M9A, D-M9A(V)
D-M9(V) D-A9, D-A9V
D-M9W(V) 2.5 2.5 3 3.5 1 5 5
D-M9A(V) 2 5 10
∗ Since the operating range is provided as a guideline
including hysteresis, it cannot be guaranteed (assuming
approximately ±30% dispersion). It may vary
substantially depending on an ambient environment.

Mounting and Moving Auto Switches

Watchmaker’s screwdriver

Auto switch mounting screw

q Fit an auto switch into the auto switch mounting groove to set it roughly to the
mounting position for an auto switch.
w After reconfirming the detecting position, tighten the auto switch mounting screw∗ to
secure the auto switch.
e Modification of the detecting position should be made in the condition of q.
Auto switch ∗ When tightening an auto switch mounting screw, use a watchmaker’s screwdriver with a handle of
approximately 5 to 6 mm in diameter.
(Use a tightening torque of approximately 0.10 to 0.20 N · m.)

Tightening torque for auto switch

mounting screw (N·m)
Auto switch model Tightening torque
D-A9(V) 0.10 to 0.20
D-M9(V)
D-M9W(V) 0.05 to 0.15
D-M9A(V)

Specific Product Precautions

Before handling auto switches, refer to pages 8 to 12 for Auto Switches Precautions.

Caution
1. If auto switch cylinders are used in parallel, keep the distance
between cylinders in accordance with the below chart.

Mounting Pitch (mm)

Bore size
Auto switch model
4 6 10 16
D-A9(V) — 20 25 30
D-M9(V)
D-M9W(V) 25 25 30 35 Mounting pitch
D-M9A(V)
Use caution not to use them, getting closer than the specified
pitch. Otherwise, it may cause auto switch to malfunction.

32
 CJP2 Series
Made to Order: Individual Specifications
Please contact SMC for detailed dimensions, specifications and lead times.
Made
to
Order

Symbol
1 Clevis / Trunnion Type Mounting Interchangeable -X1666
CJP2 series standard model no. X1666 CJ1
Clevis / Trunnion type mounting interchangeable (Former CJP)
CJP

Specifications CJ2
Applicable series CJP2
Bore size ø6, ø10, ø16
JCM
Other specifications Same as standard type. CM2
∗ ø6 is available for both standard and built-in magnet types.
∗ ø10 and ø16 are available for the standard type (The built-in magnet type is CM3
interchangeable.)

CG1
CG3
Dimensions
JMB
MB
ZZ + Stroke
H
A'
MB1
CA2
CS1
CS2
Z + Stroke

Bore size(mm) A' H Z ZZ

18.5 26.5
6 (13.5) (21.5)
43.5 47.5

10 17 25 49 55.5
16 19 29 53 63
∗ Dimensions other than above are same as basic type.
( ): For the built-in magnet type

D-
-X
Technical
Data
33
 CJP2 Series
Specific Product Precautions
Be sure to read this before handling the products. Please consult with SMC for the use
other than the specifications.

Mounting

Caution w Do not apply more tightening torque than the below specified
range when attaching a load on the rod end, rod end cap,
Mounting nut maximum tightening torque and panel single or double knuckle joint.
width Applicable bore size Thread size
Maximum tightening
q Do not apply more torque than the maximum torque range torque (N·m)
when mounting the cylinder or bracket. Also, do not attach a ø4 M2 x 0.4 0.1
panel with a thickness beyond the specified range. ø6 M3 x 0.5 0.3
ø10 M4 x 0.7 0.8
Maximum A dimension
Cylinder Thread ø16 M5 x 0.8 1.6
tightening maximum value
bore size
torque (N·m) (mm)
ø4 M8 x 1 6.2 3
Load
ø6 M10 x 1 12.5 4
ø10 M12 x 1 21.0 4
ø16 M14 x 1 34.0 5

Panel

Rod end load mounting

Rod end cap (flat type) Rod end cap (round type)

Panel mounting Panel maximum thickness

Flange bracket

Rod end cap (flat type) mounting Rod end cap (round type) mounting

Foot bracket Single knuckle joint Double knuckle joint

Foot mounting Flange mounting

Single knuckle joint mounting Double knuckle joint mounting

Piping Disassembly and Maintenance

Caution Caution
The piping port size of CJ26 and CJP210 is M3 x 0.5. Snap ring installation / removal
If using piping tube O.D. ø6, piping is possible on M3 1. To replace seals or grease the cylinder during maintenance,
One-touch fittings (applicable tube O.D. ø4) when use an appropriate pair of pliers (tool for installing a C-type re-
used with a reducer (KQ2R06-04A). taining ring for hole).
After re-installing the cylinder, make sure that the retaining
∗ For details of One-touch fittings, refer to Best Pneumatics No. 7. ring is placed securely in the groove before supplying air.
2. To remove and install the retaining ring for the knuckle pin or
the trunnion pin, use an appropriate pair of pliers (tool for in-
stalling a C-type retaining ring for hole). In particular, use a
pair of ultra-mini pliers, for removing and installing the retain-
ing rings on the ø6 cylinder.
Do not disassemble the CJP4 cylinder. Do not loosen or re-
move the head cover.

A 34
 Pin Cylinder: Single Acting, Spring Return

CJP Series
ø4, ø6, ø10, ø15
CJ1
A short stroke miniature cyl- How to Order CJP
inder with a shorter overall
length.
The installation space can be significantly
CJP B 10 15 H4 CJ2

reduced because this cylinder can be JCM

Pin cylinder Made to Order
recessed directly into a machine body or
installed on a panel. Thus, the machine
Refer to the table below.
CM2
can be made more compact.
Mounting Rod end thread CM3
B Panel mount type Nil With thread
S Embedded type B Without thread CG1
Bore size Hose nipple CG3
4 4 mm (Applicable to the mounting
6
10
6 mm type B panel mount type JMB
10 mm (ø6 to ø15) only.)
15 15 mm (Hose nipple is not attached to
embedded type.)
MB
Nil Without hose nipple ∗
Cylinder standard stroke (mm) H4 For ø4/ø2.5 tubing MB1
ø4, ø6, ø10, ø15 5, 10, 15 H6 For ø6/ø4 tubing
Embedded type Panel mount type ∗ Refer to caution on piping on page 39. CA2
Symbol Specifications CS1
Single acting, Spring return

Action Single acting, Spring return CS2

Maximum operating pressure 0.7 MPa
ø4 0.3 MPa
Minimum operating
pressure ø6 0.2 MPa
Made to Order (ø6 to ø15) ø10, ø15 0.15 MPa
(For details, refer to pages 1703 to 1896.)
Proof pressure 1 MPa
Symbol Specifications
Ambient and fluid temperature –10 to 70°C (No freezing)
XC17 Pin cylinder with rod quenched
Lubrication Not required (Non-lube)
XC22 Fluororubber seals
Piston speed 50 to 500 mm/s
Cushion None
Mounting +1.0
Stroke length tolerance 0

Panel mount type Embedded type Rod end type With thread/Without thread
Mounting Panel mount type Embedded type

Mounting nut (1)

Accessory Standard Mounting nut (2)
Gasket (1)
(Standard equipment Rod end nut (2) ∗
Rod end nut (2) ∗
equipment)
Option Hose nipple (Except ø4) —
∗ When rod end is threaded.
∗ For details about the hose nipple (accessory), refer to page 39.

Moisture
Control Tube Application Examples
IDK Series
When operating an actuator with a small diameter Clamper Ejector Gripper Stopper
and a short stroke at a high frequency, the dew
condensation (water droplet) may occur inside the
piping depending on the conditions.
D-
Simply connecting the moisture control tube to the
actuator will prevent dew condensation from oc- -X
curring. For details, refer to the IDK series in the
Best Pneumatics No. 6. Technical
Data
35
CJP2 Series

Standard Stroke Weight Theoretical Output

(g) (N)
Bore size (mm) Stroke (mm) Stroke (mm) Bore size Operating Operating pressure (MPa)
Model
4 5, 10, 15 5 10 15 (mm) direction 0.3 0.5 0.7
6 5, 10, 15 CJP4 10 13 15 OUT 0.97 3.48 6.00
4
10 5, 10, 15 CJP6 10.6 13.1 15.6 IN 1.0
15 5, 10, 15 CJP10 28 33 38 OUT 4.56 10.2 15.9
6
CJP15 72 82 92 IN 1.42
∗ Weight of hose nipple (4 g) for panel mounting is OUT 17.6 33.3 49.0
excluded. 10
IN 2.45
OUT 42.2 77.5 113
15
Spring Reaction Force Hose Nipple Dedicated for IN 4.41

(N)
Panel Mount Type
(With fixed orifice)
Bore size Stroke Retracted Extended
(mm) (mm) side side
4 5, 10, 15 2.80 1.00 Applicable tubing Part no.
6 5, 10, 15 3.92 1.42 For ø4/ø2.5 tubing CJ-5H-4
10 5, 10, 15 5.98 2.45 For ø6/ø4 tubing CJ-5H-6
15 5, 10, 15 10.80 4.41
∗ Same spring force for each stroke.

Construction (Not able to disassemble.)

Panel mount type Embedded type
i e u q rw t y

Component Parts
No. Description Material Note
1 Cover Brass Electroless nickel plated Mounting nut
2 Piston Stainless steel
ø4 Brass + Electroless nickel plated
3 Collar Oil-impregnated sintered alloy
ø6, ø10 Bronze
4 Return spring Steel wire Zinc chromated
Material: Brass
5 Piston seal NBR
Applicable
6 Gasket NBR Special product (O-ring) embedded type only Part no.
bore size (mm) d H B C
7 Mounting nut Brass Electroless nickel plated SNPS-004 4 M8 x 1.0 3 10 11.5
8 Rod end nut Steel Zinc chromated SNPS-006 6 M10 x 1.0 3 12 13.9
SNPS-010 10 M15 x 1.5 4 19 22
Dedicated Nut / Part No. SNPS-015 15 M22 x 1.5 5 27 31
Bore size
(mm) 4 6 10 15
Description Rod end nut
Mounting nut SNPS-004 SNPS-006 SNPS-010 SNPS-015
Rod end nut NTJ-004 NTP-006 NTP-010 NTP-015

Replacement Parts / Gasket Material: Steel

Bore size (mm) Order no. Contents Applicable
Part no.
bore size (mm) d H B C
4 CJPS4-G
6 CJPS6-G ∗ For the plug mounting type NTJ-004 4 M2 x 0.4 1.6 4 4.6
Above no. y
10 CJPS10-G ∗ Since gaskets (10 pcs./set) do not include a NTP-006 6 M3 x 0.5 1.8 5.5 6.4
grease pack (10 g), order it separately.
15 CJPS15-G Grease pack part number: GR-S-010 (10g) NTP-010 10 M4 x 0.7 2.4 7 8.1
∗ Dedicated for the embedded type. NTP-015 15 M5 x 0.8 3.2 8 9.2

36
 Pin Cylinder: Single Acting, Spring Return CJP Series

Allowable Kinetic Energy

Caution
When driving an inertial load, operate a cylinder with kinetic energy within the allowable value. The range in the
chart below that is delineated by bold solid lines indicates the relation between load mass and maximum driving
speeds. CJ1
Bore size (mm) 4 6 10 15 CJP
Piston speed (m/s) 0.05 to 0.5
Allowable kinetic energy (J) 0.5 x 10-3 3x 10-3 8x 10-3 19 x 10-3 CJ2
10.000 JCM
ø15

1.000
ø10 CM2
ø6
Load mass (kg)

CM3
ø4
0.100 CG1
CG3
0.010
JMB

0.001 MB
100
Maximum speed V (mm/s) MB1
CA2
Allowable Lateral Load CS1
Strictly observe the limiting range of lateral load on a piston rod. (Refer to the below graph.) If this product is used CS2
beyond the limits, it may shorten the machine life or cause damage.

0.7
ø15
0.6
Allowable lateral load W (N)

0.5

0.4

ø10
0.3

0.2
ø6
0.1

ø4
0.0
5 10 15
Stroke ST (mm)

D-
-X
Technical
Data
37
CJP Series

Recommended Mounting Hole Dimensions for Embedded Type

When embedded (mm)
Bore size
(mm)
Stroke A B C D E F G

Air 5 12 8.5 6
4 10 20 16.5 14 3.5 M8 x 1.0 6.5 3
15 28 24.5 22
G 5 16 12.5 10
6 10 23 19.5 17 3.5 M10 x 1.0 8.5 3
Machining dimensions E A
15 30 26.5 24
for mounting B –0.5
0
D O-ring seal
5 17 13.5 10.5
C 10 10 23.5 20 17 3.5 M15 x 1.5 12 4
15 30.5 27 24
5 19 14.5 11.5
øFH8

Air
15 10 25 20.5 17.5 4.5 M22 x 1.5 19 5
15 31.5 27 24
Note) E and øF should be machined in a concentric manner.

Dimensions: Panel Mount Type

CJPB4 Exhaust port NN M3 x 0.5
Rod end nut
MM C
0.
3
øG
C

øQ

H
W
R

(mm)
B A F E Bore size F
H S (mm)
A B C E st st st
G H K MM
5 10 15
Z 4 6 10 11.5 3 13 21 29 6.5 7.5 — M2 x 0.4
ø8.5 (ø6.5)

6 7 12 13.9 6 12.5 19.5 26.5 8.5 9 3.5 M3 x 0.5

CJPB6, 10, 15 NN M5 x 0.8 10 10 19 22 6 14.5 21 28 12 12 3.5 M4 x 0.7
Exhaust port ø6: C0.5
ø10,15: C1 MM 15 12 27 31 7 16.5 22.5 29 19 14 4.2 M5 x 0.8

Bore size S Z
øQ

øG

NN R W Q
C

(mm) 5st 10st 15st 5st 10st 15st

H Hose nipple 4 M8 x 1.0 7 16 24 32 3 23.5 31.5 39.5 2
W K Refer to page 39.
Without 6 M10 x 1.0 9 18.5 25.5 32.5 3 27.5 34.5 41.5 3
R rod end thread A F E Mounting dimensions of
B H S CJ-5H-6. ( ) denotes 10 M15 x 1.5 13 20.5 27 34 4 32.5 39 46 5
Rod end nut the dimensions of 15 M22 x 1.5 20 23.5 29.5 36 5 37.5 43.5 50 6
Z 13 (12)
Refer to page 36. CJ-5H-4.

Dimensions: Embedded Type

CJPS4 Exhaust port NN
MM
ø0.4

C
0.
3
øGd9
C

øQ

R W K H (mm)
B A F E Bore size F
H S (mm)
A B C E st st st
G H K MM
5 10 15
Z
4 6 10 11.5 6 10 18 26 6.5 7.5 3.5 M2 x 0.4
CJPS6, 10, 15 6 7 12 13.9 6 12.5 19.5 26.5 8.5 9 3.5 M3 x 0.5
NN 10 10 19 22 14.5 21 28
Exhaust port ø6: C0.5 6 12 12 3.5 M4 x 0.7
MM
ø0.8

ø10,15: C1 15 12 27 31 7 16.5 22.5 29 19 14 4.2 M5 x 0.8

øGd9

S Z
øQ

Bore size
C

(mm)
NN R W Q
5st 10st 15st 5st 10st 15st
H
W K 4 M8 x 1.0 7 16 24 32 3 23.5 31.5 39.5 2
R Without
rod end thread A F E 6 M10 x 1.0 9 18.5 25.5 32.5 3 27.5 34.5 41.5 3
B H S 10 M15 x 1.5 13 20.5 27 34 4 32.5 39 46 5
Rod end nut
Refer to page 36. Z 15 M22 x 1.5 20 23.5 29.5 36 5 37.5 43.5 50 6
38
 CJP Series
Specific Product Precautions
Be sure to read this before handling the products. Please consult with SMC for the use
other than the specifications.

Piping Mounting

Caution Caution CJ1

The following fittings are recommended for this cylin- Do not use it in such a way that a load could be ap-
der connection. However, there may be a case where plied to the piston rod during the retraction. CJP
the piston speed exceeds 500 mm/sec. even with the The spring that is built into the cylinder provides only
recommended fittings for this cylinder. Use a speed enough force to retract the piston rod. Thus, if a load CJ2
controller in such cases. is applied, the piston rod may not be able to retract to
the end of the stroke.
JCM
Cylinder Applicable Connection
Fitting type Model
bore size bore size thread CM2
One-touch fitting KQ202-M3G
ø4 M3 x 0.5
ø2
Miniature fitting M-3AU-2 CM3
One-touch fitting KQ202-M5N
ø6
ø10
Miniature fitting
M5 x 0.8
M-5AU-2 CG1
ø15 ø4/2.5 Dedicated hose nipple CJ-5H-4
ø6/4 (with fixed orifice) CJ-5H-6 CG3
∗ Please be aware that cylinder speed may slow down on the retracting side when us-
ing the above one-touch fittings and miniature fittings with a cylinder bore size of
ø15. JMB
Hose nipple
CJ-5H-4 CJ-5H-6
MB
(For ø4/ø2.5 tubing) (For ø6/ø4 tubing)
MB1
CA2
Width across flats 7

Gasket
CS1
Gasket
Width across flats 8
CS2
In addition to the above fittings and hose nipples, the
below fittings can also be attached to the cylinder.
When using the below fittings be sure to provide a
speed controller after adjusting it to 500 mm/s or less.
Cylinder Applicable Connection
Fitting type Model
bore size bore size thread
3.2 KQ223-M3G
ø4 M3 x 0.5
4 KQ204-M3G
One-touch
ø6 3.2
fitting
KQ223-M5
ø10 4 M5 x 0.8 KQ204-M5
ø15 6 KQ206-M5
Recommended Speed Controller
Applicable Connection Elbow type Universal type In-line type
bore size (mm) thread meter-in meter-in meter-in
M3 AS1211F-M3-02 —
ø2 AS1002F-02
M5 AS1211F-M5E-02A —
M3 AS1211F-M3-23 AS1311F-M3-23
ø3.2 AS1002F-23
M5 AS1211F-M5E-23A AS1311F-M5E-23A
M3 AS1211F-M3-04 AS1311F-M3-04
ø4 AS1002F-04
M5 AS1211F-M5E-04A AS1311F-M5E-04A
ø6 M5 AS1211F-M5E-06A AS1311F-M5E-06A AS1002F-06
∗ For details about one-touch fittings, miniature fittings and speed controllers (applicable
tubing O.D. ø2 only), refer to the Best Pneumatics No. 7.
Also, for details about speed controllers (applicable tubing O.D. ø3.2 to ø6), refer to
the Best Pneumatics No. 7. D-
∗ Refer to the Fittings and Tubing Precautions (Best Pneumatics No. 7) for how to
handle one-touch fittings.
-X
Technical
Data
39 A