SERVICE MANUAL

D-ILA PROJECTION TELEVISION

12
2005
YA337

HD-56FH96,
HD-61FH96,
HD-70FH96
BASIC CHASSIS

RA

[HD-70FH96]

TABLE OF CONTENTS
1 PRECAUTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-3
2 SPECIFIC SERVICE INSTRUCTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-7
3 DISASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-10
4 ADJUSTMENT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-31
5 TROUBLESHOOTING . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-39

COPYRIGHT © 2005 Victor Company of Japan, Limited No.YA337

2005/12
 SPECIFICATION
Contents
Items
HD-56FH96 HD-61FH96 HD-70FH96
Dimensions ( W × H × D ) 131.8 cm × 96.7 cm × 43.4 cm 145.6 cm × 104.3 cm × 46.7 cm 162.6 cm × 116.8 cm × 51.9 cm
(52" × 38-1/8" × 17-1/8") (57-3/8" × 41-1/8" × 18-3/8") (64-1/8" × 46" × 20-1/2")
Mass 43 kg (95 lbs) 47 kg (104 lbs) 72 kg (159 lbs)
TV RF System (Analog Analog CCIR (M)
/ Digital) Digital ATSC terrestrial / Digital cable
Color System (Analog) NTSC
Stereo System (Analog) BTSC (Multi Channel Sound)
Teletext System (Analog) Closed caption (T1-T4 / CC1-CC4)
TV Receiving Channels VHF Low 02ch - 06ch : 54MHz - 88MHz
and Frequency VHF High 07ch - 13ch : 174MHz - 216MHz
(Analog) UHF 14ch - 69ch : 470MHz - 806MHz
CATV 54MHz - 804MHz
Low Band : 02 - 06
High Band : 07 - 13
Mid Band : 14 - 22
Super Band : 23 - 36
Hyper Band : 37 - 64
Ultra Band : 65 - 94, 100 - 135
Sub Mid Band : 01, 96 - 99
TV / CATV Total Channel 191 Channels
Intermediate Frequen- Video IF 45.75 MHz
cy (Analog) Sound IF 41.25 MHz (4.5MHz)
Color Sub Carrier Frequency (Analog) 3.58 MHz
Power Input AC120V, 60Hz
Power Consumption 215W 220W
Projection Source 110W High-pressure mercury lamp
Projection Device D-ILA device (Reflection active matrix type LCD) x 3(R / G /B)
Resolution Total=H:1952 × V:1088 [ Effective =H:1920 × V:1080 ]
Screen Transparent screen (unitized fresnel lens / lenticular lens), aspect ratio 16:9
Screen Size 56" (142cm) Measured diagonally 61" (155cm) Measured diagonally 70" (178cm) Measured diagonally
H:124 cm × V:69.7cm H:135 cm × V:76.0cm H:155.5 cm × V:87.2cm
Audio Power Output 10W + 10W
Speaker 10cm round type × 2 (Oblique corn)
Antenna Terminal (VHF/UHF, ATSC / DIGITAL CABLE IN) F-type connector, 75Ω unbalanced, coaxial × 2
Video / Audio Input Component Video RCA pin jack × 6
[INPUT-1/2/3/4] [INPUT-1/2]
1125i / 750p Y : 1V (p-p) (Sync signal: 0.35V(p-p), 3-value sync.), 75 Ω
Pb/Pr : ±0.35V(p-p), 75 Ω
525p / 525i Y : 1V (p-p), positive (Negative sync provided), 75 Ω
Pb/Pr : 0.7V(p-p), 75 Ω
S-Video Mini-DIN 4 pin × 3
[INPUT-1/3/4] Y: 1V (p-p), positive (Negative sync provided), 75 Ω
C: 0.286V (p-p) (Burst signal), 75 Ω
Video 1V (p-p), positive (Negative sync provided), 75 Ω, RCA pin jack × 4
Audio 500mV (rms), high impedance, RCA pin jack × 8
Digital Input Video HDMI 2-row 19pin connector × 2
(Digital-input terminal is not compatible with picture signals of personal computer)
Audio Digital: HDMI 2-row 19pin connector × 21
Anarog: 500mV(rms) (-4dBs), high impedance, RCA pin jack × 2
PC (RGB) Input D-sub 3-row 15pin × 1
R/G/B : 0.7V (p-p), 75Ω
HD / VD : 1V (p-p) to 5V (p-p), high impedance
< Available signal >
VGA : 640 pixels × 480 pixels (Horizontal : 31.5kHz / Vertical : 60Hz)
XGA : 1024 pixels × 768 pixels (Horizontal : 48.4kHz / Vertical : 60Hz)
Center Channel Input 500mV(rms) (-4dBs), high impedance, RCA pin jack × 1
Monitor / Recording S-Video Mini-DIN 4pin × 1
Output Y: 1V (p-p), 75Ω
C: 0.286V(p-p) (burst signal), 75Ω
Video 1V (p-p), 75Ω, RCA pin jack × 1
Audio 250mV(rms) (-10dBs), Fs-18dB low impedance, RCA pin jack × 2
Audio Output RCA pin jack × 2
Variable More than 0 to 1000mV (rms) (+2.2dBs)
Fix 500mV(rms) (-4dBs), low impedance (1000Hz when modulated 100%)
iLink Input/Output TS In/Out (4-pin, S400) × 2, IEEE1394 compliant DTCP digital copy protection compatible
Digital Audio Optical Output Digital SPDIF × 1
AV COMPULINK lll 3.5mm mini jack × 1
RS-232C D-sub 2-row 9 pin [External control for TV set]
Remote Control Unit RM-C14G (AA/R6 / UM-3 battery × 2)

Design & specifications are subject to change without notice.

1-2 (No.YA337)
 SECTION 1
PRECAUTION
1.1 SAFETY PRECAUTIONS
(1) The design of this product contains special hardware, (6) Isolation Check (Safety for Electrical Shock Hazard)
many circuits and components specially for safety After re-assembling the product, always perform an
purposes. For continued protection, no changes should be isolation check on the exposed metal parts of the cabinet
made to the original design unless authorized in writing by (antenna terminals, video/audio input and output terminals,
the manufacturer. Replacement parts must be identical to Control knobs, metal cabinet, screw heads, earphone jack,
those used in the original circuits. Service should be control shafts, etc.) to be sure the product is safe to operate
performed by qualified personnel only. without danger of electrical shock.
(2) Alterations of the design or circuitry of the products should a) Dielectric Strength Test
not be made. Any design alterations or additions will void The isolation between the AC primary circuit and all metal
the manufacturer's warranty and will further relieve the parts exposed to the user, particularly any exposed metal
manufacturer of responsibility for personal injury or part having a return path to the chassis should withstand a
property damage resulting therefrom. voltage of 3000V AC (r.m.s.) for a period of one second. (.
(3) Many electrical and mechanical parts in the products have . . . Withstand a voltage of 1100V AC (r.m.s.) to an
special safety-related characteristics. These appliance rated up to 120V, and 3000V AC (r.m.s.) to an
characteristics are often not evident from visual inspection appliance rated 200V or more, for a period of one second.)
nor can the protection afforded by them necessarily be This method of test requires a test equipment not generally
obtained by using replacement components rated for found in the service trade.
higher voltage, wattage, etc. Replacement parts which b) Leakage Current Check
have these special safety characteristics are identified in Plug the AC line cord directly into the AC outlet (do not use
the parts list of Service manual. Electrical components a line isolation transformer during this check.). Using a
having such features are identified by shading on the "Leakage Current Tester", measure the leakage current
schematics and by ( ) on the parts list in Service from each exposed metal part of the cabinet, particularly
manual. The use of a substitute replacement which does any exposed metal part having a return path to the chassis,
not have the same safety characteristics as the to a known good earth ground (water pipe, etc.). Any
recommended replacement part shown in the parts list of leakage current must not exceed 0.5mA AC (r.m.s.).
Service manual may cause shock, fire, or other hazards. However, in tropical area, this must not exceed 0.2mA AC
(4) Don't short between the LIVE side ground and (r.m.s.).
ISOLATED (NEUTRAL) side ground or EARTH side Alternate Check Method
ground when repairing. Plug the AC line cord directly into the AC outlet (do not
Some model's power circuit is partly different in the GND. use a line isolation transformer during this check.). Use
The difference of the GND is shown by the LIVE : ( ) side an AC voltmeter having 1000Ω per volt or more
GND, the ISOLATED (NEUTRAL) : ( ) side GND and sensitivity in the following manner. Connect a 1500Ω
EARTH : ( ) side GND. 10W resistor paralleled by a 0.15µF AC-type capacitor
Don't short between the LIVE side GND and ISOLATED between an exposed metal part and a known good earth
(NEUTRAL) side GND or EARTH side GND and never ground (water pipe, etc.). Measure the AC voltage
measure the LIVE side GND and ISOLATED (NEUTRAL) across the resistor with the AC voltmeter. Move the
side GND or EARTH side GND at the same time with a resistor connection to each exposed metal part,
measuring apparatus (oscilloscope etc.). If above note will particularly any exposed metal part having a return path
not be kept, a fuse or any parts will be broken. to the chassis, and measure the AC voltage across the
(5) When service is required, observe the original lead dress. resistor. Now, reverse the plug in the AC outlet and
Extra precaution should be given to assure correct lead repeat each measurement. Any voltage measured must
dress in the high voltage circuit area. Where a short circuit not exceed 0.75V AC (r.m.s.). This corresponds to
has occurred, those components that indicate evidence of 0.5mA AC (r.m.s.).
overheating should be replaced. Always use the However, in tropical area, this must not exceed 0.3V AC
manufacturer's replacement components. (r.m.s.). This corresponds to 0.2mA AC (r.m.s.).
AC VOLTMETER
(HAVING 1000 /V,
OR MORE SENSITIVITY)

0.15 F AC-TYPE

PLACE THIS PROBE

ON EACH EXPOSED
1500 10W METAL PART
GOOD EARTH GROUND

(No.YA337)1-3
1.2 INSTALLATION 1.3 LAMP UNIT HANDLING CAUTION
1.2.1 HEAT DISSIPATION
If the heat dissipation vent behind this unit is blocked, cooling LAMP UNIT : TS-CL110UAA
efficiency may deteriorate and temperature inside the unit will
rise. The temperature sensor that protects the unit will be
activated when internal temperature exceeds the predetermined
level and power will be turned off automatically.
Therefore, please make sure pay attention not to block the heat
dissipation vent as well as the ventilation outlet behind the unit
and ensure that there is room for ventilation around it.
Do not put foreign objects near the ventilation holes as this
can result in fire or electrical hazards.
Do not block the ventilation holes as this may cause the
internal temperature to rise and possibly result fire.

1.3.1 PRECAUTION FOR LAMP UNIT

The lamp emits high intensity white, ultraviolet and infrared
light. Do not look directly at the light during service.
Also, do not touch the lamp directly as it presents a burn
hazard.
Handle with extra care. This lamp emits high heat and
contains high-pressure during use.
Do not give any impact as this may cause the broken lamp.

Exhaust hole
Intake hole
*Diagram differs from actual appearance. 1.3.2 HOW TO CONFIRM LAMP OPERATING TIME
• MAXIMUM COUNT TIME= 65535 hours
(1) Set to "0 minutes" using the [SLEEP TIMER] key.
1.2.2 INSTALLATION REQUIREMENTS (2) Press the [VIDEO STATUS] key and [DISPLAY] key
Ensure that the minimal distance is maintained, as specified simultaneously, then enter the SERVICE MODE.
fingure, between the unit with and the surrounding walls, as well (3) When the Main Menu is displayed, press [2] key to enter
as the floor etc. the SELF CHECK MODE.
Install the unit on stable flooring. (4) The use time of a lamp is displayed on middle of the screen
Take precautionary measures to prevent the unit from tipping in by the hexadecimal number of 4 figures.
order to protect against accidents and earthquakes.
SERVICE MENU SCREEN
CAUTION FOR INSTALLATION
• Do not tilt the TV towards the left or right, or toward the back.
• Install the TV in a corner on the floor so as to keep cords out SERVICE MENU
1. ADJUST
of the way. 2. SELF CHECK
• The TV will generate a slight amount of heat during 3. I2C STOP

operation. Ensure that sufficient space is available around

the TV to allow satisfactory cooling.

200mm
200mm

150mm 150mm SELF CHECK MODE SCREEN (Page 1)

50mm

LOB 0 FAN 0
AUD 0
ANA 9 DIG 9
*Diagram differs from actual appearance. 0000 0
0

Lamp operation time

1-4 (No.YA337)
1.3.3 LAMP UNIT REPLACEMENT 1.3.6 PRECAUTION FOR REPLACEMENT
(1) The lamp replacement message will appear when need to • Do not replace the LAMP UNIT immediately after the projector
change the lamp. After replace the lamp, need to reset the has been used.
timer which is built into TV. • The temperature of the LAMP UNIT is still high and could
(2) Life of the lamp unit is about 6000 hours over. Lamp use cause a burn.
time can be check at the lamp message MENU. • Allow a cooling period of 1 hour or more before performing
(3) If Fig.1 message appears when turn the TV on, need to replacement.
replace the lamp. • Before starting LAMP UNIT replacement work, turn off the
(4) Use the lamp timer reset only after replacing the lamp. MAIN POWER switch, and disconnect the AC power cord plug
NOTE: from the wall outlet.
• This message will appear every time turn on the TV, when • If touched, the lamp glass surface may rupture and burns may
the lamp needs to be replaced. Press the [OK] key to make result. Do not touch the glass portion or metal portion. Handle
the message disappear, or replace the lamp. only plastic handle.
• The replaced old lamp can be discarded in the same manner
as a fluorescent lamp. Check local ordinances and dispose of
LAMP REPLACEMENT MESSAGE the used lamp as prescribed.

LAMP NEEDS TO BE REPLACED.

REFER TO OWNER'S MANUAL FOR
REPLACEMENT INSTRUCTIONS.

AFTER REPLACING THE LAMP,

PLEASE RESET TIMER IN THE TV
MENU.

PRESS OK, IF YOU DO NOT WANT

TO SEE THIS MESSAGE AGAIN.

Fig.1

1.3.4 HOW TO REPLACE THE LAMP UNIT

• Refer to the "USERS GUIDE" for a detailed operating
description.
(1) Turn off the TV power.
(2) After the LAMP LED light has stopped blinking, disconnect
the power cord from the AC outlet.
(3) Loosen 1 screw then take out the lamp cover below the left
side of the TV.
(4) Loosen 2 screws then take out the lamp unit.
(5) Install the new lamp unit.
(6) Re-install the lamp cover.
NOTE:
• After installing the new lamp unit, do not forget to reset the
lamp timer.

1.3.5 HOW TO RESET THE LAMP TIMER

• Refer to the "USERS GUIDE" for a detailed operating
description.
(1) Press the [MENU] key to select CLOCK / TIMERS.
(2) Select the <LAMP TIMER RESET> with [] / [] keys.
(3) Enter the <LAMP TIMER RESET> mode the message will
appears.
(4) Press the [OK] key while the above message appears on
the screen.
(5) Turn off the power, then turn on the power.
(6) The lamp timer has now been reset, as before the HOW TO
CONFIRM LAMP OPERATING TIME.

(No.YA337)1-5
1.4 SERVICE PARTS KIT INSTRUCTIONS 1.5 SCREEN HANDLING CAUTIONS
Due to the character of this product, these OPTICAL /DRIVE 1.5.1 SCREEN STORAGE
ASS'Y are prepared. Store the SCREEN ASS'Y in a standing position in order to avoid
Please note these OPTICAL/DRIVE ASS'Y when replacing or deformation. If the screen is stored horizontally, there is risk of
ordering the parts. deforming the screen face.
When necessary to place the SCREEN ASS'Y horizontally,
OPTICAL/DRIVE ASS'Y position the screen side upwards and sure to place spacers
between the screen and resting site (floor or stand etc.) to
prevent the screen from sagging.

1.5.2 SCREEN SURFACE

Since the screen surface is easily scratched or soiled, use ample
care when handling.

1.5.3 PRECAUTIONS FOR CLEANING AND REPLACEMENT

• The SCREEN ASS'Y is made from the lenticular lens and
fresnel lens. The anti static proceeding and the surface of the
lenticular lens. Rubbing the surface with something hard, the
coating may peel off.
• When the screen is dirty, gently wipe it with a soft cloth.
If the screen is very dirty, wipe it down with a cloth dipped in a
1.4.1 PART NUMBER AND CONSTRUCTION diluted kitchen cleaner (neutrality detergent) and thoroughly
wrung-out. Then wipe immediately after with clean, dry cloth.
Kit parts number Kit part name Never use the organic solvent such as the alcohol or benzine.
TS-COP8A-SAA OPTICAL / DRIVE ASS'Y • The SCREEN ASS'Y replacement is required if the coating
was peel off. Alkaline detergent or acidity detergent can not be
be used.
1.4.2 OPTICAL / DRIVE ASS'Y CONSTRUCTION • The notched side of the lenticular lens and the fresnel lens are
(1) OPTICAL BLOCK faced each other.
(Included D-ILA DEVICE, PROJECTION LENS) • Do not rub the screen when cleaning it or replaceing it.
(2) OPTICAL BASE Rubbing the screen may cause of the scratch of the screen by
(3) DRIVE PWB ASS'Y its notch.
This PWB is mounted with 1 memory IC saved with
adjustment, setting data of the drive circuit.
(4) SHIELD COVER
*The following parts without the kits part.
• REMOTE SENSOR PWB ASS'Y
• LAMP UNIT
• LAMP FAN DUCT
• THERMOSTAT

1.4.3 PRECAUTION FOR USING

(1) In the case of the following defects/problems, replace this
kit (OPTICAL/DRIVE ASS'Y)
a) Picture defect caused by optical system/D-ILA device
related parts.
b) Picture defect caused by drive circuit.
(2) The DRIVE PWB ASS'Y is mounted with a memory IC
[IC3753] saved with adjustment/setting data (GAMMA,
SHADING, etc.) of the drive circuit.
The data of this memory IC is in the optimal state according
to individual D-ILA devices and each section of the
OPTICAL BLOCK.
(3) When replace the DRIVE PWB ASS'Y, take off the 1
memory IC from the original board and replace with new
one. When replace the DRIVE PWB ASS'Y, do same
manner. Replace 1 memory IC.
(4) After the replacement of the OPTICAL BLOCK, projection
lens focus adjustment and drive convergence / projection
adjustment are required.

1-6 (No.YA337)
 SECTION 2
SPECIFIC SERVICE INSTRUCTIONS
2.1 SYSTEM SETTEING

Be sure to carry out the following operation at the end of

the procedure. SERVICE MENU SCREEN

(1) Set to "0 minutes" using the [SLEEP TIMER] key.

SERVICE MENU
(2) While "0 minutes" is displayed, press the [VIDEO 1. ADJUST
STATUS] key and [DISPLAY] key simultaneously, then 2. SELF CHECK
3. I2C STOP
enter the SERVICE MODE.
(3) When the SERVICE MENU SCREEN is displayed, press
[2] key to enter the self check mode.
(4) Turn off the power by pressing the [POWER] key on the
remote control unit.

SELF CHECK MODE SCREEN

LOB 0 FAN 0
AUD 0

ANA 9 DIG 9
0000 0
0

2.2 FEATURES
Built in ATSC (Advanced Television Systems Committee) DIGITAL INPUT
TUNER Digital-in will display when any picture signal in Digital-in is
This TV can receive both Digital broadcasting (ATSC) and displayed.
Analogue broadcasting. V-CHIP
D.I.S.T. (Digital Image Scaling Technology) Since the V-CHIP is built in, it can choose, view and listen to a
This system uses line interpolation to double the number of healthy program.
scanning lines and achieve high resolution, flicker-free picture. MTS STEREO
SMART CAPTION The voice multiplex function of the MTS system is built in.
Smart caption will appear when you press the MUTING button, (MTS = Multi channel Television Sound system)
only on channels where the broadcast contains CLOSED NATURAL CINEMA
CAPTION information. Watching the movie or animation, press the Natural Cinema to
VIDEO STATUS adjust the out line of the images to make thin more sharp.
Expression of a favorite screen can be chosen by the VIDEO VIDEO INPUT LABEL
STATUS function. This function is used to label video input connections for the
onscreen displays.

2.3 MAIN DIFFRENCE LIST

Item HD-56FH96 HD-61FH96 HD-70FH96

MEDIA CARD VIEWER NO NO YES
DIGITAL PWB SRA0D003A-M2 SRA0D002A-M2 SRA0D001A-M2
ANALOG PWB SRA-1002A-M2 ← SRA-1001A-M2
POWER PWB SRA-9002A-M2 ← SRA-9001A-M2
CARD VIEWER PWB -------- -------- SRP-8511A-M2

(No.YA337)1-7
2.4 TECHNICAL INFORMATION
2.4.1 D-ILA DEVICE SPECIFICATION 2.4.4 D-ILA DEVICE STRUCTURE
Item Content
R / G / B DEVICE (SIDE VIEW)
Resolution H: 1952 × V:1088
Pixel number about 2123776 Glass
substrate
Pixel size H : 8.1µm × V :8.1µm
Aspect ratio 16 : 9
Incident light
Contrast ratio 5000 : 1 Projection light
Aperture ratio 89% or more Back
Plane
Effective pixel measurement 0.7 inch FRONT

Flat film
2.4.2 PROJECTION UNIT

R DEVICE

Reflective pixel Liquid Transparent

electrode crystal electrode

B DEVICE

Incident light PIXEL VIEW (FRONT VIEW)

G DEVICE Lamp unit

OPTICAL IRIS

2.4.3 IMAGE LIGHT FLOW

DEVICE UNIT SECTION (TOP VIEW) 8.1 m

Pixel
8.1 m

Projection
light

G B R Mirror
FRONT
Device

B
RG B
Device

R Incident
light

Device
Mirror Mirror
G

1-8 (No.YA337)
2.4.5 MAIN CPU PIN FUNCTION [IC7601 : DIGITAL PWB ASS'Y]
Pin Pin name I/O Function Pin Pin name I/O Function
1 VHOLD1 I Data slice for main screen closed caption 51 NC O Not used
2 HFLT1 I/O LPF for main screen closed caption video input 52 NC O Not used
3 NC O Not used 53 NC O Not used
4 NC O Not used 54 NC O Not used
5 DIGR0 O R [0] for OSD 55 NC O Not used
6 TB1in I AC power for timer clock 56 NC O Not used
7 REMO I Remote control 57 NC O Not used
8 BYTE I Data bus width select [L = 16bit (fixed)] 58 NC O Not used
9 CNVss I CPU programming mode select [Normal = L] 59 NC O Not used
10 DIGG0 O G [0] for OSD 60 NC O Not used
11 DIGB0 O B [0] for OSD 61 NC O Not used
12 RESET I Reset for main CPU [Reset = L] 62 HSYNC I H. sync for OSD
13 Xout O System clock osillation (crystal) : 16MHz 63 NC O Not used
14 Vss - GND 64 VSYNC I V. sync for OSD
15 Xin I System clock osillation (crystal) : 16MHz 65 NC O Not used
16 VccI I 3.3V stand-by power supply 66 NC O Not used
17 OSC1 I Clock for OSD 67 NC O Not used
18 OSC2 O Not used : Clock for OSD 68 NC O Not used
19 INT1 I AV COMPULINK control 69 NC O Not used
20 INT0 I Request for sub(chassis) CPU communication (serial data) 70 NC O Not used
21 OUT1 O Ys (blanking) for OSD 71 P2.1 O Clock for Inter IC (serial) bus control
22 OUT2 O YM (transparence) for OSD 72 P2.0 I/O Data for Inter IC (serial) bus control
23 NC O Not used 73 NC O Not used
24 NC O Not used 74 NC O Not used
25 NC O Not used 75 NC O Not used
26 NC O Not used 76 NC O Not used
27 CTA2/RTS2 O Not used 77 NC O Not used
28 CLK2 O Not used 78 NC O Not used
29 RxD2 I Digital tuner control 79 NC O Not used
30 TxD2 O Digital tuner control 80 P1.0 O Function LED lighting
31 SDA2 I/O Not used 81 P0.7 O Communication LED lighting
32 DIGR1 O R [1] for OSD 82 P0.6 O Test point
33 DIGG1 O G [1] for OSD 83 NC O Not used
34 DIGB1 O B [1] for OSD 84 WAKE O Reset for sub(chassis) CPU
35 TxD0 I Data receive (serial) for external programming 85 CARD_DET I Not used
36 RxD0 O Data transmission (serial) for external programming 86 POWER_SW I Power switch (mechanical) detection
37 CLK0 I Clock for external programming 87 SDA I/O Data for Inter IC (serial) bus control : memory
38 RTS0 O Busy for external programming [Operation = H] 88 SLC O Clock for Inter IC (serial) bus control : memory
39 P5.7 I Not used 89 DIGR2 O R [2] for OSD
40 P5.6 O Not used 90 DIGG2 O G [2] for OSD
41 HOLD I CPU programming mode select [Normal = H] 91 DIGB2 O B [2] for OSD
42 P5.4 O Not used 92 NC O Not used
43 P5.3 O Not used 93 KEY2 I Key scan data for front control button (MENU/CH+/CH-) KEY2
44 P5.2 O Not used 94 KEY1 I Key scan data for front control button (INPUT/VOL+/VOL-) KEY1
45 P5.1 O Not used 95 VHOLD2 I Data slice for sub screen closed caption
46 WR O CPU programming mode select [Normal = L] 96 HLF2 I/O LPF for sub screen closed caption video input
47 P4.7 O Data transmission for sub(chassis) CPU communication (serial) 97 CVIN2 I Video(Y) for sub screen closed caption
48 P4.6 I Data receive for sub(chassis) CPU communication (serial) 98 TVSETB I Test terminal [L Fixed]
49 P4.5 I Clock for sub(chassis) CPU communication (serial) 99 VCCE I 5V stand-by power supply
50 P4.4 O Not used 100 CVIN1 I Video(Y) for main screen closed caption

(No.YA337)1-9
 SECTION 3
DISASSEMBLY
3.1 DISASSEMBLY PROCEDURE
CAUTION AT DISASSEMBLY:
• Be sure to perform the SYSTEM SETTEING, at the end of the procedure.
• Make sure that the power cord is disconnected from the outlet.
• Pay special attention not to break or damage the parts.
• When removing each board, remove the connectors as required. Taking notes of the connecting points (connector numbers)
makes service procedure manageable.
• Make sure that there is no bent or stain on the connectors before inserting, and firmly insert the connectors.
• Wait until the LAMP UNIT has cool down is completely.
• While not in repair service, place the chassis back its original position.

3.1.1 FRONT SIDE DISASSEMBLY [HD-56FH96]

3.1.1.1 REMOVING THE SPEAKER GRILL (Fig.1) 3.1.1.8 REMOVING THE SCREEN BLOCK (Fig.1)
(1) Remove the 2 screws [A]. • Remove the SPEAKER GRILL.
(2) Remove the SPEAKER GRILL. • Remove the FRONT PANEL.
NOTE: (1) Remove the 8 screws [J].
As a speaker grille is depressed downward, it is removed. (2) Remove the FRONT PANEL.
CAUTION :
• Place the SCREEN BLOCK on a flat table without fail.
3.1.1.2 REMOVING THE ORNAMENT PANEL (Fig.1) • Because of the large size, at least 2 persons are
• Remove the SPEAKER GRILL. recommended for removal and reassemble.
(1) Remove the 6 screws [B]. • Use care not to scratch the screen during work.
(2) Remove the ORNAMENT PANEL. • During assembly, be sure to engage the left and right tabs
with the cabinet mounting positions.
• When supporting the SCREEN BLOCK, avoid grasping the
3.1.1.3 REMOVING THE CENTER PANEL (Fig.1) top of the screen panel, instead grasp the left and right
• Remove the SPEAKER GRILL. areas.
(1) Remove the 4 screws [C]. • Do not leave the SCREEN BLOCK removed for long time to
(2) Remove the CENTER PANEL. prevent soiling from dust.

3.1.1.4 REMOVING THE FRONT LED PWB (Fig.1) 3.1.1.9 REMOVING THE SCREEN ASS'Y (Fig.1)
• Remove the SPEAKER GRILL. • Remove the SPEAKER GRILL.
(1) Remove the 2 screws [D]. • Remove the FRONT PANEL.
(2) Remove the FRONT LED PWB. • Remove the SCREEN BLOCK.
NOTE: (1) Remove the 12 screws [K].
Remove the earth wire connected to the FRONT LED PWB (2) Remove the SCREEN ASS'Y.
simultaneously.

3.1.1.5 REMOVING THE SPEAKER (Fig.1)

• Remove the SPEAKER GRILL.
(1) Remove the 4 screws [E].
(2) Remove the SPEAKER.
(3) Remove the opposite SPEAKER same steps.

3.1.1.6 REMOVING THE CENTER COVER (Fig.1)

• Remove the SPEAKER GRILL.
(1) Remove the 2 screws [F].
(2) Remove the CENTER COVER.

3.1.1.7 REMOVING THE FRONT PANEL (Fig.1)

• Remove the SPEAKER GRILL.
(1) Remove the 10 screws [G].
(2) Remove the 12 screws [H].
(3) Remove the FRONT PANEL.

1-10 (No.YA337)
 SCREEN BRACKET SCREEN BLOCK

FRONT BRACKET
SCREEN ASS'Y

BACK COVER

SCREEN BLOCK

FRONT PANEL
MAIN BODY

A
CENTER COVER

SPEAKER

B J
B
E G
C

FRONT
LED PWB
E
SPEAKER

CENTER
PANEL
SPEAKER GRILL
FRONT ORNAMENT PANEL
Fig.1

(No.YA337)1-11
3.1.1.10 REMOVING THE MIRROR (Fig.2) 3.1.1.13 REMOVING THE BACK COVER (Fig.2)
• Remove the SPEAKER GRILL. • Remove the SPEAKER GRILL.
• Remove the FRONT PANEL. • Remove the FRONT PANEL.
• Remove the SCREEN BLOCK. • Remove the SCREEN BLOCK.
(1) Remove the 4 screws [A] attaching the MIRROR HOLDER • Remove the SUPPORT HOLDER.
of the upper side. (1) Remove the 6 screws [F] and the 2 screws [G].
(2) Remove the 6 screws [B] attaching the MIRROR HOLDER (2) Remove the BACK COVER
of left and right side. CAUTION :
(3) Raise slightly to disengage of the MIRROR from the bottom • Because of the large size, at least 2 persons are
holder recommended for removal and reassemble.
(4) Remove the MIRROR.
NOTE :
• Do not touch the front of the MIRROR. 3.1.1.14 REMOVING THE SPEAKER BOX (Fig.2)
• Do not shock the the MIRROR. • Remove the SPEAKER GRILL.
• Because of the large size, at least 2 persons are • Remove the FRONT PANEL.
recommended for removal and reassemble. • Remove the SCREEN BLOCK.
• Remove the SUPPORT HOLDER.
• Remove the BACK COVER.
3.1.1.11 REMOVING THE SIDE CONTROL PWB (Fig.2) (1) Remove the 2 screws [H].
• Remove the SPEAKER GRILL. (2) Remove the SPEAKER BOX.
• Remove the FRONT PANEL. (3) Remove the opposite SPEAKER BOX same steps.
• Remove the SCREEN BLOCK.
(1) Remove the 2 screws [C].
(2) Remove the SIDE CONTROL BASE.
(3) Remove the 2 screws [D].
(4) Remove the SIDE CONTROL PWB.

3.1.1.12 REMOVING THE SUPPORT HOLDER (Fig.2)

• Remove the SPEAKER GRILL.
• Remove the FRONT PANEL.
• Remove the SCREEN BLOCK.
(1) Remove the 2 screws [E].
(2) Remove the SUPPORT HOLDER.

1-12 (No.YA337)
 BACK COVER

MIRROR HOLDER
MIRROR HOLDER

MIRROR MIRROR HOLDER

B
F

SIDE CONTROL
PWB

H G
SPEAKER
BOX
D

MAIN BODY

C
SIDE CONTROL
BASE

SUPPORT HOLDER

FRONT
E

SPEAKER
BOX
Fig.2

(No.YA337)1-13
3.1.2 FRONT SIDE DISASSEMBLY [HD-61FH96]
3.1.2.1 REMOVING THE SPEAKER GRILL (Fig.3) 3.1.2.7 REMOVING THE CENTER COVER (Fig.3)
(1) Remove the 2 screws [A]. • Remove the SPEAKER GRILL.
(2) Remove the SPEAKER GRILL. • Remove the FRONT PANEL with SCREEN ASS'Y.
NOTE : (1) Remove the 2 screws [J].
As a speaker grille is depressed downward, it is removed. (2) Remove the CENTER COVER.

3.1.2.2 REMOVING THE ORNAMENT PANEL (Fig.3) 3.1.2.8 REMOVING THE SPEAKER (Fig.3)
• Remove the SPEAKER GRILL. • Remove the SPEAKER GRILL.
(1) Remove the 6 screws [B]. • Remove the FRONT PANEL with SCREEN ASS'Y.
(2) Remove the ORNAMENT PANEL. (1) Remove the 4 screws [K].
(2) Remove the SPEAKER.
3.1.2.3 REMOVING THE CENTER PANEL (Fig.3) (3) Remove the opposite SPEAKER same steps.
• Remove the SPEAKER GRILL.
(1) Remove the 4 screws [C].
(2) Remove the CENTER PANEL. 3.1.2.9 REMOVING THE SPEAKER PLATE (Fig.3)
• Remove the SPEAKER GRILL.
3.1.2.4 REMOVING THE FRONT LED PWB (Fig.5) • Remove the FRONT PANEL with SCREEN ASS'Y.
• Remove the SPEAKER GRILL. • Remove the SPEAKER.
(1) Remove the 2 screws [D]. (1) Remove the 6 screws [L].
(2) Remove the FRONT LED PWB. (2) Remove the SPEAKER PLATE.

NOTE :
Remove the earth wire connected to the FRONT LED PWB 3.1.2.10 REMOVING THE BACK COVER FILTER (Fig.3)
simultaneously. • Remove the SPEAKER GRILL.
• Remove the FRONT PANEL with SCREEN ASS'Y.
(1) Remove the 1 screw [M].
3.1.2.5 REMOVING THE FRONT PANEL WITH SCREEN (2) Remove the FILTER COVER with BACK COVER FILTER.
ASS'Y (Fig.3) (3) Remove the BACK COVER FILTER from FILTER COVER.
• Remove the SPEAKER GRILL.
(1) Remove the 10 screws [E] and 4 screws [F].
(2) Remove the FRONT PANEL with SCREEN ASS'Y.
CAUTION :
• Place the FRONT PANEL with SCREEN ASS'Y on a flat
table without fail.
• Because of the large size, at least 2 persons are
recommended for removal and reassemble.
• Use care not to scratch the screen during work.
• Do not leave the FRONT PANEL with SCREEN ASS'Y
removed for long time to prevent soiling from dust.

3.1.2.6 REMOVING THE SCREEN ASS'Y (Fig.3)

• Remove the SPEAKER GRILL.
• Remove the FRONT PANEL with SCREEN ASS'Y.
(1) Remove the 20 screws [G] and 4 screws [H].
(2) Remove the SCREEN BRACKET.
(3) Remove the SCREEN ASS'Y from the FRONT PANEL.

1-14 (No.YA337)
 BACK COVER E

SPEAKER
PLATE

SPEAKER

K
BACK COVER
M FILTER
L
FILTER
COVER A
M
J CENTER
COVER SPEAKER
L PLATE
SCREEN BRACKET
G
SPEAKER

FRONT PANEL

B FRONT SCREEN ASS'Y

LED PWB SCREEN BRACKET
D
E
C

CENTER
PANEL
SPEAKER GRILL
FRONT ORNAMENT PANEL
Fig.3

(No.YA337)1-15
3.1.2.11 REMOVING THE MIRROR (Fig.4) 3.1.2.13 REMOVING THE CORNER COVER (Fig.4)
• Remove the SPEAKER GRILL. • Remove the SPEAKER GRILL.
• Remove the FRONT PANEL. • Remove the FRONT PANEL.
(1) Remove the 6 screws [A] attaching the MIRROR HOLDER (1) Remove the 1 screw [E].
of the upper side. (2) Remove the CORNER COVER.
(2) Remove the 6 screws [B] attaching the MIRROR HOLDER (3) Remove the opposite CORNER COVER same steps.
of left and right side.
(3) Raise slightly to disengage of the MIRROR from the bottom
holder 3.1.2.14 REMOVING THE BACK COVER (Fig. 4)
(4) Remove the MIRROR. • Remove the SPEAKER GRILL.
NOTE : • Remove the FRONT PANEL.
• Do not touch the front of the MIRROR. • Remove the SPEAKER and SPEAKER PLATE.
• Do not shock the MIRROR. (1) Remove the 2 screws [F], 9 screws [G] and 6 screws [H].
• Because of the large size, at least 2 persons are (2) Remove the BACK COVER from MAIN BODY.
recommended for removal and reassemble. CAUTION :
• Because of the large size, at least 2 persons are
recommended for removal and reassemble.
3.1.2.12 REMOVING THE SIDE CONTROL PWB (Fig.4)
• Remove the SPEAKER GRILL.
• Remove the FRONT PANEL.
(1) Remove the 2 screws [C].
(2) Remove the SIDE CONTROL BASE.
(3) Remove the 2 screws [D].
(4) Remove the SIDE CONTROL PWB.

1-16 (No.YA337)
 BACK COVER

MIRROR HOLDER

MIRROR HOLDER CORNER

COVER

MIRROR HOLDER

F H
MIRROR

SIDE CONTROL
PWB E
B CORNER
COVER

MAIN BODY
D

C SIDE CONTROL
BASE

FRONT

Fig.4

(No.YA337)1-17
3.1.3 FRONT SIDE DISASSEMBLY [HD-70FH96]
3.1.3.1 REMOVING THE SPEAKER GRILL (Fig.5) 3.1.3.7 REMOVING THE SCREEN BLOCK (Fig.5)
(1) Remove the 2 screws [A]. • Remove the SPEAKER GRILL.
(2) Remove the SPEAKER GRILL. • Remove the SPEAKER.
NOTE : • Remove the FRONT PANEL.
As a speaker grille is depressed downward, it is removed. (1) Remove the 6 screws [H] and 8 screws [J].
(2) Remove the SCREEN BLOCK.
CAUTION :
3.1.3.2 REMOVING THE ORNAMENT PANEL (Fig.5) • Place the SCREEN BLOCK on a flat table without fail.
• Remove the SPEAKER GRILL. • Because of the large size, at least 2 persons are
(1) Remove the 6 screws [B]. recommended for removal and reassemble.
(2) Remove the ORNAMENT PANEL. • Use care not to scratch the screen during work.
• During assembly, be sure to engage the left and right tabs
with the cabinet mounting positions.
3.1.3.3 REMOVING THE CENTER PANEL (Fig.5) • When supporting the SCREEN BLOCK, avoid grasping the
• Remove the SPEAKER GRILL. top of the screen panel, instead grasp the left and right
(1) Remove the 4 screws [C]. areas.
(2) Remove the CENTER PANEL. • Do not leave the SCREEN BLOCK removed for long time to
prevent soiling from dust.

3.1.3.4 REMOVING THE FRONT LED PWB (Fig.5)

• Remove the SPEAKER GRILL. 3.1.3.8 REMOVING THE SCREEN ASS'Y (Fig.5)
(1) Remove the 2 screws [D]. • Remove the SPEAKER GRILL.
(2) Remove the FRONT LED PWB. • Remove the SPEAKER.
NOTE : • Remove the FRONT PANEL.
Remove the earth wire connected to the FRONT LED PWB • Remove the SCREEN BLOCK.
simultaneously. (1) Remove the 12 screws [K].
(2) Remove the SCREEN BRACKET and SCREEN ASS'Y.

3.1.3.5 REMOVING THE SPEAKER (Fig.5)

• Remove the SPEAKER GRILL. 3.1.3.9 REMOVING THE CENTER COVER (Fig.5)
(1) Remove the 4 screws [E]. • Remove the SPEAKER GRILL.
(2) Remove the SPEAKER. • Remove the FRONT PANEL.
(3) Remove the opposite SPEAKER same steps. (1) Remove the 2 screws [L].
(2) Remove the CENTER PANEL.

3.1.3.6 REMOVING THE FRONT PANEL (Fig.5)

• Remove the SPEAKER GRILL.
• Remove the SPEAKER.
(1) Remove the 10 screws [F] from rear side.
(2) Remove the 20 screws [G] from front side.
(3) Remove the FRONT PANEL.

1-18 (No.YA337)
 SCREEN BLOCK
K
SCREEN ASS'Y
SCREEN BRACKET

F
SCREEN BRACKET
BACK COVER

FRONT PANEL H

MAIN BODY

SCREEN BLOCK

SPEAKER

E
B J
D

C CENTRE COVER
L
FRONT
LED PWB

E
G
FRONT
SPEAKER
CENTER PANEL
ORNAMENT PANEL SPEAKER GRILL
Fig.5

(No.YA337)1-19
3.1.3.10 REMOVING THE MIRROR (Fig.6) 3.1.3.12 REMOVING THE SIDE CONTROL PWB (Fig.6)
• Remove the SPEAKER GRILL. • Remove the SPEAKER GRILL.
• Remove the SPEAKER. • Remove the SPEAKER.
• Remove the FRONT PANEL. • Remove the FRONT PANEL.
• Remove the SCREEN BLOCK. • Remove the SCREEN BLOCK.
(1) Remove the 2 screws [A] attaching the MIRROR HOLDER (1) Remove the 4 screws [M].
STOPPER. (2) Remove the SIDE CONTROL BASE.
(2) Remove the 2 screws [B] and 2 screws [C] attaching the (3) Remove the 2 screws [N].
MIRROR HOLDER upper side. (4) Remove the SIDE CONTROL PWB.
(3) Remove the 2 screws [D], 6 screws [E] and 2 screws [F]
attaching the MIRROR HOLDER of left and right side.
(4) Raise slightly to disengage of the MIRROR from the bottom 3.1.3.13 REMOVING THE SPEAKER BOX (Fig.6)
holder • Remove the SPEAKER GRILL.
NOTE : • Remove the SPEAKER.
• Do not touch the front of the MIRROR. • Remove the FRONT PANEL.
• Do not shock the MIRROR. • Remove the SCREEN BLOCK.
• Because of the large size, at least 2 persons are • Remove the BACK COVER BRACKET.
recommended for removal and reassemble. (1) Remove the 3 screws [P].
(2) Remove the SPEAKER BOX.
(3) Remove the opposite SPEAKER BOX same steps.
3.1.3.11 REMOVING THE BACK COVER BRACKET (Fig.6)
• Remove the SPEAKER GRILL.
• Remove the SPEAKER. 3.1.3.14 REMOVING THE BACK COVER (Fig.6)
• Remove the FRONT PANEL. • Remove the SPEAKER GRILL.
• Remove the SCREEN BLOCK. • Remove the SPEAKER.
(1) Remove the 6 screws [G] and 3 screws [H]. • Remove the FRONT PANEL.
(2) Remove the rear side BACK COVER BRACKET. • Remove the SCREEN BLOCK.
(3) Remove the 4 screws [J], 1 screw [K] and 1 screw [L]. • Remove the BACK COVER BRACKET.
(4) Remove the left side BACK COVER BRACKET. • Remove the SPEAKER BOX.
(5) Remove the righ side BACK COVER BRACKET same (1) Remove the 4 screws [Q] and 2 screws [R].
step. (2) Remove the BACK COVER.

1-20 (No.YA337)
C B MIRROR HOLDER STOPPER BACK COVER
P
A
MIRROR HOLDER(top)

MIRROR HOLDER
BRACKET(top)
D E
D

MIRROR
HOLDER MIRROR
HOLDER P
(side)
(side)

F
E
MIRROR
R
G

F Q

BACK COVER
BRACKET
(REAR) H
SIDE
CONTROL
N PWB
G
BACK COVER
BRACKET
J (L/R)

K
L
M SIDE
CONTROL
BASE

BACK COVER J
BRACKET
(FRONT) P
MAIN BODY

SPEAKER BOX

FRONT
SPEAKER BOX

Fig.6

(No.YA337)1-21
3.1.4 REAR SIDE DISASSEMBLY 3.1.4.4 REMOVING THE AV TERMINAL BOARD (Fig.7)
3.1.4.1 REMOVING THE LAMP UNIT (Fig.7) • Remove the LAMP COVER.
(1) Remove the 1 screw [A]. • Remove the BODY COVER.
(2) Remove the LAMP COVER. • Remove the BODY BRACKET.
(3) Remove the 2 screws [B] • Remove the MAIN UNIT.
(4) Pull out the LAMP UNIT. (1) Remove the 3 screws [G], 2 screws [H], 6 screws [J], 3
screws [K].
NOTE : (2) Remove the 4 hex screws [L].
• Do not leave the LAMP COVER removed for long time to (3) Remove the nut attaching the ANTENNA TERMINAL.
prevent dirt and dust form covering the lens. (4) Remove the AV TERMINAL BOARD.
• Make sure that the LAMP COVER is completely installed.

3.1.4.5 REMOVING THE POWER PWB (Fig.7)

3.1.4.2 REMOVING THE BODY COVER (Fig.7) • Remove the LAMP COVER.
(1) Remove the 11 screws [C] and the 5 screws [D] • Remove the BODY COVER.
(2) Remove the BODY COVER. • Remove the BODY BRACKET.
NOTE : • Remove the MAIN UNIT.
• Do not leave the BODY COVER removed for long time to (1) Remove the POWER CORD.
prevent soiling from dust. (2) Remove the 5 screws [M].
(3) Remove the POWER PWB.

3.1.4.3 REMOVING THE MAIN UNIT (Fig.7)

• Remove the LAMP COVER. 3.1.4.6 REMOVING THE TUNER PWB (Fig.7)
• Remove the BODY COVER. • Remove the LAMP COVER.
(1) Remove the 4 screws [E] • Remove the BODY COVER.
(2) Remove the BODY BRACKET. • Remove the BODY BRACKET.
(3) Remove the 2 screws [F] • Remove the MAIN UNIT.
(4) The MAIN UNIT is pulled out to the back side. (1) Remove the 1 screw [N].
(2) Remove the HANGER BRACKET with TUNER PWB.
CAUTION :
(3) Remove the 4 screws [P].
• Except for confirmation of projection images on the screen
(4) Remove the TUNER PWB.
and audio output through the speakers, the removed MAIN
UNIT is still workable in the same state as if it is still built-in
the TV set. Therefore, the MAIN UNIT can be removed, if
3.1.4.7 REMOVING THE ANALOG PWB (Fig.7)
necessary, for board diagnosis, electric testing, etc. apart
• Remove the LAMP COVER.
from confirmation of screen images and audio output. Do not
• Remove the BODY COVER.
leave the MAIN UNIT removed for long time to prevent
• Remove the BODY BRACKET.
soiling from dust.
• Remove the MAIN UNIT.
• Because of the large size, at least 2 persons are
• Remove the POWER PWB and TUNER PWB.
recommended for removal and reassemble.
• Remove the AV TERMINAL BOARD.
• When carrying the MAIN UNIT, use care not to drop, shock
(1) Remove the 4 screws [Q].
or shake it.
(2) Remove the ANALOG PWB.
• Do not stain or damage the projection lens.
• Do not look directly at the light during service.
• Do not touch the lamp directly as it presents a burn hazard.
3.1.4.8 REMOVING THE DIGITAL PWB (Fig.7)
NOTE : • Remove the LAMP COVER.
• When not performing repair work, attach the cap on the lens • Remove the BODY COVER.
to preventing dust from covering. • Remove the BODY BRACKET.
• When mounting to the set, make sure the front of the lens is • Remove the MAIN UNIT.
in contact with the cushion on the set (body) side. • Remove the POWER PWB and TUNER PWB.
• Make sure that FRONT LED PWB connector is completely (1) Remove the 1 screw [R].
connect to the ANALOG PWB connector. (2) Remove the DIGITAL PWB BRACKET with DIGITAL PWB
• When wire clamps are removed during work, use care to and ATSC TUNER MODULE.
restore them precisely to their original positions. (3) Remove the 4 screws [S].
Performance can be affected if these are not returned to the (4) Remove the DIGITAL PWB SHIELD COVER.
original positions. (5) Remove the 9 screws [T].
(6) Remove the DIGITAL PWB.
CAUTION :
Make sure to perform the "SYSTEM SETTEING", when
DIGITAL PWB is replaced.

1-22 (No.YA337)
3.1.4.9 REMOVING THE ATSC TUNER MODULE PWB (Fig.7) 3.1.4.11 REMOVING THE IRIS PWB (Fig.7)
• Remove the LAMP COVER. • Remove the LAMP COVER.
• Remove the BODY COVER. • Remove the BODY COVER.
• Remove the BODY BRACKET. • Remove the BODY BRACKET.
• Remove the MAIN UNIT. • Remove the MAIN UNIT.
• Remove the POWER PWB and TUNER PWB. • Remove the POWER PWB and TUNER PWB.
(1) Remove the 1 screw [R]. (1) Remove the 2 screws [Z].
(2) Remove the DIGITAL PWB BRACKET with ATSC TUNER (2) Remove the IRIS PWB.
MODULE PWB.
(3) Remove the 4 screws [U].
(4) Remove the ATSC TUNER COOLING FAN. 3.1.4.12 REMOVING THE REMOCON PWB (Fig.7)
(5) Remove the 8 screws [V]. • Remove the LAMP COVER.
(6) Remove the ATSC TUNER SHIELD COVER. • Remove the BODY COVER.
(7) Remove the 5 screws [W]. • Remove the BODY BRACKET.
(8) Remove the ATSC TUNER MODULE PWB. • Remove the MAIN UNIT.
• Remove the POWER PWB and TUNER PWB.
(1) Remove the 1 screw [a].
3.1.4.10 REMOVING THE SD CARD PWB (Fig.7) (2) Remove the REMOCON PWB.
• Remove the LAMP COVER.
• Remove the BODY COVER.
• Remove the BODY BRACKET.
• Remove the MAIN UNIT.
• Remove the AV TERMINAL BOARD.
(1) Remove the 2 screws [X].
(2) Remove the SD CARD BRACKET with SD CARD PWB.
(3) Remove the 2 screws.
(4) Remove the SD CARD PWB.

(No.YA337)1-23
 LAMP UNIT B
MAIN BODY
A

FRONT LAMP COVER

BODY BRACKE
TUNER PWB DIGITAL PWB S
N T
R
P
HANGER ATSC TUNER
BRACKET SHIELD COVER

ATSC TUNER W
COOLING FAN
DIGITAL PWB
SHIELD COVER

POWER ANALOG PWB

PWB DIGITAL PWB
BRACKET
M
ATSC TUNER MODULE PWB
V
U

Y SD CARD PWB

SD CARD
BRACKET
AV TERMINAL BOARD

X BODY COVER

ANTENNA
MAIN UNIT TERMINAL J

F
L

H K

G
POWER CORD

Fig.7

1-24 (No.YA337)
3.1.4.13 REMOVING THE LAMP COVER SW PWB (Fig.8) 3.1.4.18 REMOVING THE IRIS PWB (Fig.8)
• Remove the LAMP COVER. • Remove the LAMP COVER.
• Remove the BODY COVER. • Remove the BODY COVER.
• Remove the BODY BRACKET. • Remove the BODY BRACKET.
• Remove the MAIN UNIT. • Remove the MAIN UNIT.
(1) Remove the 2 screws [A]. (1) Remove the 2 screws [K].
(2) Remove the LAMP COVER SW BRACKET with LAMP (2) Remove the IRIS PWB.
COVER SW PWB.
(3) Remove the 1 screw [B].
(4) Remove the LAMP COVER SW PWB. 3.1.4.19 REMOVING THE REMOCON PWB(Fig.8)
• Remove the LAMP COVER.
• Remove the BODY COVER.
3.1.4.14 REMOVING THE LAMP FAN DUCT (Fig.8) • Remove the BODY BRACKET.
• Remove the LAMP COVER. • Remove the MAIN UNIT.
• Remove the BODY COVER. (1) Remove the 1 screws [a].
• Remove the BODY BRACKET. (2) Remove the REMOCON PWB.
• Remove the MAIN UNIT.
(1) Remove the 2 screws [C].
(2) Remove the THERMOSTAT. 3.1.4.20 REMOVING THE OPTICAL / DRIVE ASS'Y (Fig.8)
(3) Remove the 5 screws [D]. • Remove the LAMP COVER.
(4) Remove the LAMP FAN DUCT. • Remove the BODY COVER.
• Remove the BODY BRACKET.
• Remove the MAIN UNIT.
3.1.4.15 REMOVING THE LAMP COOLING FAN (Fig.8) • Remove the LAMP FAN DUCT.
• Remove the LAMP COVER. (1) Remove the 5 screw [L], 6 screw [M] and 1 screw [N].
• Remove the BODY COVER. (2) Remove the OPTICAL / DRIVE ASS'Y.
• Remove the BODY BRACKET. NOTE :
• Remove the MAIN UNIT. • The OPTICAL / DRIVE ASS'Y contains precision
(1) Remove the 2 screws [E]. opticalcomponents.
(2) Remove the COOLING FAN BRACKET by pulling • Handle carefully and avoid imparting strong shock.
transversally • OPTICAL / DRIVE ASS'Y construction
(3) Remove the 2 screws [F]. (1) OPTICAL BLOCK:
(4) Remove the LAMP COOLING FAN. (D-ILA device, PBS, Field lens, Integrater, Mirror etc.)
(2) PROJECTION LENS
(3) OPTICAL BASE
3.1.4.16 REMOVING THE BALLAST UNIT COOLING FAN (4) DRIVE PWB
(Fig.8) (5) IRIS PWB
• Remove the LAMP COVER. (6) TOP DUCT
• Remove the BODY COVER. (7) SHIELD COVER
• Remove the BODY BRACKET. • When not performing repair work, attach the cap on the lens to
• Remove the MAIN UNIT. preventing dust from covering.
• Remove the COOLING FAN BRACKET. • When mounting to the set, make sure the front of the lens side
(1) Remove the 2 screws [G]. is in contact with the cushion on the body side.
(2) Remove the BALLAST UNIT COOLING FAN. • Do not leave the OPTICAL / DRIVE ASS'Y removed for long
time to prevent soiling from dust.
3.1.4.17 REMOVING THE LAMP BALLAST BLOCK (Fig.8)
• Remove the LAMP COVER. 3.1.4.21 REMOVING THE DRIVE PWB (Fig.8)
• Remove the BODY COVER. • Remove the LAMP COVER.
• Remove the BODY BRACKET. • Remove the BODY COVER.
• Remove the MAIN UNIT.. • Remove the BODY BRACKET.
(1) Remove the 1 screw [H]. • Remove the MAIN UNIT.
(2) Remove the LAMP BALLAST BLOCK. (1) Slide the TOP DUCT PLATE and remove it.
(3) Remove the 2 screws [I]. (2) Remove the 1 screw [P] and the 1 screw [Q].
(4) Remove the LAMP BALLAST DUCT. (3) Remove the TOP DUCT.
(5) Remove the 2 screws [J]. (4) Remove the SHIELD TOP CASE.
(6) Remove the LAMP BALLAST UNIT. (5) Remove the 2 screws [R].
(6) Remove the DEVICE SHIELD.
(7) Remove the 3 screws [S] and the 1 screw [T].
(8) Remove the DRIVE PWB.

(No.YA337)1-25
3.1.4.22 REMOVING THE OPTICAL BLOCK COOLING FAN 3.1.4.24 REMOVING THE CARD VIEWER PWB [HD-70FH96]
(Fig.8) (Fig.8)
• Remove the LAMP COVER. • Remove the LAMP COVER.
• Remove the BODY COVER. • Remove the BODY COVER.
• Remove the BODY BRACKET. • Remove the BODY BRACKET.
• Remove the MAIN UNIT. • Remove the MAIN UNIT..
• Remove the LAMP FAN DUCT. (1) Remove the 2 screws [X].
• Remove the OPTICAL / DRIVE ASS'Y (2) Remove the CARD VIEWER BRACKET.
(1) Remove the 2 screws [U]. (3) Remove the 2 screws [Y].
(2) Remove the SIROCCO TOP CASE. (4) Remove the CARD VIEWER SHIELD COVER.
(3) Remove the 2 screws [V]. (5) Remove the 4 screws [Z].
(4) Remove the OPTICAL BLOCK COOLING FAN. (6) Remove the CARD VIEWER PWB.

3.1.4.23 REMOVING THE PROJECTION LAMP(Fig.8)

• Remove the LAMP COVER.
• Remove the BODY COVER.
• Remove the BODY BRACKET.
• Remove the MAIN UNIT.
(1) Remove the 4 screws [W].
(2) Remove the PROJECTION LAMP.

1-26 (No.YA337)
 OPTICAL / DRIVE ASS'Y
C
FRONT
REMOCON TOP DUCT PLATE
PWB THERMOSTAT
P Q
LAMP BALLAST BLOCK D
LAMP BALLAST TOP DUCT
a
DUCT
K
I
IRIS LAMP FAN DUCT
PWB
DEVICE R
SHIELD G LAMP
LAMP E COOLING FAN
BALLAST SHIELD
J UNIT TOP
CASE
T
S
H
DRIVE
PWB

BALLAST UNIT
LAMP BALLAST COOLING FAN
BRACKET
F
L

COOLING FAN
BRACKET

THERMO PWB

SIROCCO TOP U SHIELD COVER

CASE
W M

V
LAMP COVER SW
BRACKET
CARD VIEWER
SHIELD COVER
OPTICAL A
Y BLOCK

OPTICAL
BLOCK N
COOLING FAN
Z
LAMP COVER
B SW PWB

CARD
VIEWER
PWB
X

CARD
VIEWER
BRACKET
UNIT BASE
(Only HD-70FH96)

Fig.8

(No.YA337)1-27
3.2 MEMORY IC REPLACEMENT
• This model uses the memory IC.
• This memory IC stores data for proper operation of the video and drive circuits.
• When replacing, be sure to use an IC containing this (initial value) data.
3.2.1 MEMORY IC TABLE
Simbol Number of pins Mounting PWB Main content of data
IC3753 8-pin DRIVE PWB Adjustment and setting data (GAMMA, SHADING, etc.) of
IC3701(DRIVE CPU) are memorized.
IC7201 48-pin DIGITAL PWB Progaram(Video process) of IC6001(System CPU) is memorized.
IC7602 8-pin DIGITAL PWB Setting value of IC7601(MAIN CPU) is memorized.

3.2.2 MEMORY IC REPLACEMENT PROCEDURE

1. Power off
Switch off the power and disconnect the power plug from the AC outlet.
2. Replace the memory IC
Be sure to use the memory IC written with the initial setting values.
3. Power on
Connect the power plug to the AC outlet and switch on the power.
4. Receiving channel setting
Refer to the OPERATING INSTRUCTIONS and set the receive channels (Channels Preset) as described.
5. User setting
Check the user setting items according to the given in page later. Where these do not agree, refer to the OPERATING
INSTRUCTIONS and set the items as described.
6. SERVICE MODE setting
Verify what to set in the SERVICE MODE, and set whatever is necessary (Fig.1). Refer to the SERVICE ADJUSTMENT for setting.

3.2.3 SERVICE MODE SETTING

„SERVICE MODE SCREEN „SETTING ITEM
Setting items Settings Item No.
SERVICE MENU SCREEN
Video system setting Adjust S001 - S009
Audio system setting Adjust T001 - T003
SERVICE MENU
1. ADJUST Main CPU system setting Fixed M001 - M224
2. SELF CHECK
3. I2C STOP
Drive system setting Fixed F001 - F002
(NOT USED) Fixed D001
(NOT USED) Fixed Z001

ADJUSTMENT MODE SCREEN

S001 R DRIVE137
NTSC3 FULL STD LOW

Fig.1

1-28 (No.YA337)
3.2.4 SETTINGS OF FACTORY SHIPMENT
3.2.4.1 BUTTON OPERATION 3.2.4.2 REMOTE CONTROL DIRECT OPERATION
Setting item Setting position Setting item Setting position
POWER Off INPUT TV
CHANNEL CABLE-02 CHANNEL CABLE-02
VOLUME 10 VOLUME 10
INPUT TV MUTING OFF
DISPLAY OFF
ASPECT NTSC Reguler
HD FULL
SLEEP TIMER OFF
THEATER PRO OFF
NATURAL CINEMA AUTO
C.C. OFF
MTS STEREO
TWIN LEFT SIDE CABLE-02
SOURCE RIGHT SIDE INPUT-1
SOUND A.H.S OFF
BBE ON
SMART SOUND OFF
HYPER BASS OFF

3.2.4.3 REMOTE CONTROL MENU OPERATION

„ PICTURE ADJUST „ SOUND ADJUST
Customers can adjust the picture setting of menu screen as their
own like but the picture standard value during factory shipment is as Setting item Setting position
below. BASS 00
[NTSC MODE] TREBLE 00
BALANCE 00
Setting item DYNAMIC STANDARD GAME THEATER
TINT +15 00 -10 00 „ CLOCK / TIMERS
COLOR 00 00 00 00
Setting item Setting position
PICTURE 00 00 00 00
ON / OFF TIMER NO
BRIGHT 00 00 00 00
DETAIL +05 00 00 00 „ INITIAL SETUP
COLOR TEMPERATURE HIGH HIGH HIGH HIGH
Setting item Setting position
COLOR MANAGEMENT ON ON ON ON
VIDEO-1 MONITOR OUT OFF
DYNAMIC GAMMA ON ON ON ON
TV SPEAKER ON
SMART PICTURE OFF ON ON ON
AUDIO OUT FIX
DIGITAL VNR AUTO AUTO AUTO AUTO
DIGITAL-IN AUTO
MPEG NR OFF OFF OFF OFF
DIGITAL-IN AUDIO AUTO
[HD MODE] CENTER CH INPUT OFF
Setting item DYNAMIC STANDARD GAME THEATER NOISE MUTING ON
PICTURE +15 00 -10 00 FRONT PANEL LOCK OFF
BRIGHT 00 00 00 00 V1 SMART INPUT OFF
COLOR 00 00 00 00 VIDEO INPUT LABEL All blank
TINT 00 00 00 00 POSITION ADJUSTMENT Center
DETAIL +05 00 00 00 POWER INDICATOR HIGH
COLOR TEMPERATURE HIGH LOW HIGH LOW LANGUAGE ENG.
COLOR MANAGEMENT ON ON ON ON CLOSED CAPTION OFF
DYNAMIC GAMMA ON ON ON ON AUTO SHUT OFF OFF
SMART PICTURE OFF ON ON ON XDS ID ON
DIGITAL VNR AUTO AUTO AUTO AUTO AUTO TUNER SETUP Unnecessary to set
MPEG NR OFF OFF OFF OFF V-CHIP OFF

(No.YA337)1-29
3.3 REPLACEMENT OF CHIP COMPONENT
3.3.1 CAUTIONS
(1) Avoid heating for more than 3 seconds.
(2) Do not rub the electrodes and the resist parts of the pattern.
(3) When removing a chip part, melt the solder adequately.
(4) Do not reuse a chip part after removing it.

3.3.2 SOLDERING IRON

(1) Use a high insulation soldering iron with a thin pointed end of it.
(2) A 30w soldering iron is recommended for easily removing parts.

3.3.3 REPLACEMENT STEPS

1. How to remove Chip parts 2. How to install Chip parts

[Resistors, capacitors, etc.] [Resistors, capacitors, etc.]

(1) As shown in the figure, push the part with tweezers and (1) Apply solder to the pattern as indicated in the figure.
alternately melt the solder at each end.

(2) Grasp the chip part with tweezers and place it on the
solder. Then heat and melt the solder at both ends of the
chip part.

(2) Shift with the tweezers and remove the chip part.

[Transistors, diodes, variable resistors, etc.]

[Transistors, diodes, variable resistors, etc.]
(1) Apply solder to the pattern as indicated in the figure.
(1) Apply extra solder to each lead. (2) Grasp the chip part with tweezers and place it on the
solder.
(3) First solder lead A as indicated in the figure.
SOLDER SOLDER

A
(2) As shown in the figure, push the part with tweezers and
alternately melt the solder at each lead. Shift and remove B
the chip part.
C

(4) Then solder leads B and C.

B
NOTE :
After removing the part, remove remaining solder from the C
pattern.

1-30 (No.YA337)
 SECTION 4
ADJUSTMENT
4.1 ADJUSTMENT PREPARATION 4.3 MEASURING INSTRUMENT AND FIXTURES
(1) There are 2 ways of adjusting this TV : One is with the • Oscilloscope
REMOTE CONTROL UNIT and the other is the • Signal generator (Pattern generator)
conventional method using adjustment parts and [NTSC / 525i / 525p / 750p / 1125i]
components. • TV audio multiplex signal generator
(2) The adjustment using the REMOTE CONTROL UNIT is • Remote control unit
made on the basis of the initial setting values. The
setting values which adjust the screen to the optimum
condition can be different from the initial setting 4.4 ADJUSTMENT ITEMS
values. „ FOCUS
(3) Make sure that connection is correctly made AC to AC • LENS FOCUS adjustment
power source.
(4) Turn on the power of the TV and measuring instruments for „ DRIVE CIRCUIT
warning up for at least 30 minutes before starting • DRIVE CONVERGENCE adjustment
adjustments. • DRIVE CENTER POSITION adjustment
(5) If the receive or input signal is not specified, use the most „ VIDEO CIRCUIT
appropriate signal for adjustment. • WHITE BALANCE (HIGHLIGHT) adjustment
(6) Never touch the parts (such as variable resistors,
„ MTS CIRCUIT
transformers and condensers) not shown in the adjustment
• MTS INPUT LEVEL adjustment
items of this service adjustment.
• MTS SEPARATION adjustment
4.2 PRESET SETTING BEFORE ADJUSTMENTS
Unless otherwise specified in the adjustment items, preset the
following functions with the REMOTE CONTROL UNIT.
Setting item Settings
VIDEO STATUS STANDARD
Picture adjustments 00
COLOR TEMPERATURE LOW
COLOR MANAGEMENT ON
DYNAMIC GAMMA ON
SMART PICTURE OFF
DIGITAL VNR OFF
MPEG NR OFF
NATURAL CINEMA AUTO
Sound adjustments 00
A.H.S OFF
BBE OFF
SMART SOUND OFF
ASPECT FULL

(No.YA337)1-31
4.5 BASIC OPERATION OF SERVICE MODE
4.5.1 HOW TO ENTER THE SERVICE MODE 4.5.4 ADJUSTMENT MODE
(1) Set to "0 minutes" using the [SLEEP TIMER] key. This mode is used to adjust the VIDEO CIRCUIT and the MTS
(2) While "0 minutes" is displayed, press the [VIDEO STA- CIRCUIT.
TUS] key and [DISPLAY] key simultaneously, then enter 4.5.4.1 HOW TO ENTER THE ADJUSTMENT MODE
the SERVICE MODE (Fig.1) When the SERVICE MENU SCREEN of SERVICE MODE is
displayed, press [1] key to enter the ADJUSTMENT MODE
(Fig.2).
SERVICE MENU SCREEN
4.5.4.2 DESCRIPTION OF STATUS DISPLAY OF
SERVICE MENU ADJUSTMENT MODE
1. ADJUST
2. SELF CHECK
3. I2C STOP
ADJUSTMENT MODE
SETTING ITEM No. SETTING ITEM SETTING VALUE (DATA)

S001 R DRIVE137
NTSC3 FULL STD LOW

Fig.1
NOTE:
• Before entering the SERVICE MODE, confirm that the
setting of TV/CATV switch of the REMOTE CONTROL UNIT
is at the "TV" side and the setting of VCR/DVD switch is at
the "VCR" side. If the switches have not been properly set,
you cannot enter the SERVICE MODE. SIGNAL SYSTEM SCREEN MODE VIDEO STATUS WHITE BALANCE
• When a number key other than the [1] or [9] keys is pressed Fig.2
in the SERVICE MENU SCREEN, the other relevant screen
may be displayed. (1) SIGNAL SYSTEM
This is not used in the adjustment procedure. Press the The signal displayed on the screen is displayed.
[MENU] key to return to the SERVICE MENU SCREEN.
NTSC3 : 525i (Composite / S-video input)
525I : 525i (Component input)
4.5.2 HOW TO EXIT THE SERVICE MODE 525P : 525p
Press the [ BACK ] key to exit the Service mode. 1125I6 : 1125i
750P : 750p
4.5.3 SERVICE MODE SELECT KEY LOCATION
PCVGA : PC (VGA)
VCR/DVD switch PCXGA : PC (XGA)
H525I : HDMI 525i
TV/CATV switch POWER H525P : HDMI 525p
SLEEP TIMER H125I6 : HDMI 1125i
DISPLAY H750P : HDMI 750p
D525I : ATSC 525i
NUMBER D525P : ATSC 525p
D125I6 : ATSC 1125i
VIDEO STATUS
CHANNEL + (2) SCREEN MODE
MUTING State of the SCREEN SIZE or MULTI PICTURE is displayed.
VOLUME +
SINGLE SCREEN
VOLUME - BACK
FULL : FULL
MENU CHANNEL -
1609 : CINEMA, CINEMA ZOOM
PANO : PANORAMA, HD PANORAMA
REGU : REGULAR
MULTI SCREEN
M2 : TWIN, FREEZE screen
M12 : INDEX screen

1-32 (No.YA337)
(3) VIDEO STATUS 4.5.5 RGB BOX PATTERN MODE
STD : STANDARD This mode is used to adjust the DRIVE CIRCUIT.
DYN : DYNAMIC 4.5.5.1 HOW TO ENTER THE RGB BOX PATTERN MODE
TH : THEATER When the SERVICE MENU SCREEN of SERVICE MODE is
displayed, press [9] key to enter the RGB BOX PATTERN
GAME : GAME
MODE (Fig3).
(4) WHITE BALANCE
4.5.5.2 DESCRIPTION OF STATUS DISPLAY OF RGB BOX
HIGH : HIGH PATTERN MODE
LOW : LOW

(5) SETTING ITEM NAME RGB BOX PATTERN MODE

Setting item name are displayed. The setting item numbers to
be displayed are listed below.
Item No. Setting item
S001 - S009 Video system setting
T001 - T003 Audio system setting
M001 - M224 Main CPU system setting
F001 - F002 Drive system setting RGB
D001 (NOT USED)
Z001 (NOT USED)
ADJUSTMENT COLOUR MODE
(6) SETTING ITEM NO.
Setting item numbers are displayed. For the setting item
names to be displayed, refer to "Initial setting value of Fig.3
adjustment mode".
(1) RGB BOX PATTERN
(7) SETTING VALUE (DATA) The checkered pattern is displayed. White is a synthesis of
The SETTING VALUE is displayed. RGB.

4.5.4.3 CHANGE AND MEMORY OF SETTING VALUE (2) ADJUSTMENT COLOR MODE
Presently selected ADJUSTMENT COLOR MODE is
„SELECTION OF SETTING ITEM
displayed.
• [CH+] / [CH-] key.
Change the setting items up/ down.
„SELECTION OF SETTING ITEM
S001... ↔ T001... ↔ M001... ↔ F001... ↔ D001... ↔ Z001... • [CH+] / [CH-] key.
Move the selected RGB BOX PATTERN up/ down pixel by
• [SLEEP TIMER] key. pixel.
Switches to the next items.
• [VOL+] / [VOL-] key.
S001 → T001 → M001... → F001... → D001 → Z001 Move the selected RGB BOX PATTERN left/ right pixel by
pixel.

„CHANGE OF SETTING VALUE (DATA) • [SLEEP TIMER] key.

• [VOL+] / [VOL-] key. Adjusts the data reset.
Change the setting values up/down.
• [DISPLAY] key.
Adjusts the selected COLOR BOX PATTERN.
„MEMORY OF SETTING VALUE (DATA)
Changed setting value is memorized by pressing [MUTING] R → B → RGB
key.
• [BACK] key.
Returns to the SERVICE MENU SCREEN from the RGB
BOX PATTERN MODE.

„MEMORY OF SETTING VALUE (DATA)

With the RGB BOX PATTERN MODE, the changed date is
written in the MEMORY instantly.

(No.YA337)1-33
4.6 INITIAL SETTING VALUES IN THE SERVICE MODE
• Perform fine-tuning based on the "initial values" using the remote control when in the Service mode.
• The "initial values" serve only as an indication rough standard and therefore the values with which optimal display can be achieved
may be different from the default values. But, don't change the values that are not written in "ADJUSTMENT PROCEDURE". They
are fixed values.
4.6.1 VIDEO SYSTEM SETTING Item No. Item Variable range Setting value
Item No. Item Variable range Setting value M028 1E1B 00 - FF 00
S001 R DRIVE 000 - 255 136 M029 1E1C 00 - FF 00
S002 G DRIVE 000 - 255 138 M030 1E1D 00 - FF 00
S003 B DRIVE 000 - 255 138 M031 1E1E 00 - FF 00
S004 RESREV 000 - 255 000 M032 1E1F 00 - FF 00
S005 RESREV 000 - 255 002 M033 1E20 00 - FF 00
S006 RESREV 000 - 255 002 M034 1E21 00 - FF 00
S007 RESREV 000 - 255 002 M035 1E22 00 - FF 00
S008 RESREV 000 - 255 002 M036 1E23 00 - FF 00
S009 RESREV 000 - 255 002 M037 1E24 00 - FF 00
4.6.2 AUDIO SYSTEM SETTING M038 1E25 00 - FF 00
M039 1E26 00 - FF 00
Item No. Item Variable range Setting value
M040 1E27 00 - FF 00
T001 INPLEVEL 000 - 015 006
M041 1E28 00 - FF 00
T002 LOWSEPA 000 - 063 020
M042 1E29 00 - FF 00
T003 HIGHSEPA 000 - 063 038
M043 1E2A 00 - FF 00
4.6.3 MAIN CPU SYSTEM SETTING (Fixed values) M044 1E2B 00 - FF 00
Item No. Item Variable range Setting value M045 1E2C 00 - FF 00
M001 1E00 00 - FF 00 M046 1E2D 00 - FF 00
M002 1E01 00 - FF 00 M047 1E2E 00 - FF 00
M003 1E02 00 - FF 0A M048 1E2F 00 - FF 00
M004 1E03 00 - FF 3B M049 1E30 00 - FF 00
M005 1E04 00 - FF 10 M050 1E31 00 - FF 00
M006 1E05 00 - FF 00 M051 1E32 00 - FF 00
M007 1E06 00 - FF 00 M052 1E33 00 - FF 00
M008 1E07 00 - FF 00 M053 1E34 00 - FF 00
M009 1E08 00 - FF 10 M054 1E35 00 - FF 00
M010 1E09 00 - FF 00 M055 1E36 00 - FF 02
M011 1E0A 00 - FF 05 M056 1E37 00 - FF 00
M012 1E0B 00 - FF 00 M057 1E38 00 - FF 01
M013 1E0C 00 - FF 01 M058 1E39 00 - FF 06
M014 1E0D 00 - FF 00 M059 1E3A 00 - FF 10
M015 1E0E 00 - FF 00 M060 1E3B 00 - FF 83
M016 1E0F 00 - FF 00 M061 1E3C 00 - FF 00
M017 1E10 00 - FF 00 M062 1E3D 00 - FF 00
M018 1E11 00 - FF 00 M063 1E3E 00 - FF 00
M019 1E12 00 - FF 00 M064 1E3F 00 - FF 00
M020 1E13 00 - FF 01 M065 1E40 00 - FF 00
M021 1E14 00 - FF 01 M066 1E41 00 - FF 00
M022 1E15 00 - FF 00 M067 1E42 00 - FF 02
M023 1E16 00 - FF 00 M068 1E43 00 - FF 03
M024 1E17 00 - FF 00 M069 1E44 00 - FF 04
M025 1E18 00 - FF 00 M070 1E45 00 - FF 03
M026 1E19 00 - FF 00 M071 1E46 00 - FF 02
M027 1E1A 00 - FF 00 M072 1E47 00 - FF 00

1-34 (No.YA337)
Item No. Item Variable range Setting value Item No. Item Variable range Setting value
M073 1E48 00 - FF 00 M123 1E7A 00 - FF 00
M074 1E49 00 - FF 00 M124 1E7B 00 - FF 00
M075 1E4A 00 - FF 00 M125 1E7C 00 - FF 00
M076 1E4B 00 - FF 00 M126 1E7D 00 - FF 00
M077 1E4C 00 - FF 00 M127 1E7E 00 - FF 01
M078 1E4D 00 - FF 00 M128 1E7F 00 - FF 00
M079 1E4E 00 - FF 00 M129 1E80 00 - FF 01
M080 1E4F 00 - FF 00 M130 1E81 00 - FF 00
M081 1E50 00 - FF 00 M131 1E82 00 - FF 01
M082 1E51 00 - FF 00 M132 1E83 00 - FF 00
M083 1E52 00 - FF 00 M133 1E84 00 - FF 00
M084 1E53 00 - FF 00 M134 1E85 00 - FF 00
M085 1E54 00 - FF 00 M135 1E86 00 - FF 00
M086 1E55 00 - FF 00 M136 1E87 00 - FF 00
M087 1E56 00 - FF 00 M137 1E88 00 - FF 00
M088 1E57 00 - FF 00 M138 1E89 00 - FF 00
M089 1E58 00 - FF 00 M139 1E8A 00 - FF 00
M090 1E59 00 - FF 00 M140 1E8B 00 - FF 00
M091 1E5A 00 - FF 00 M141 1E8C 00 - FF 00
M092 1E5B 00 - FF 00 M142 1E8D 00 - FF 00
M093 1E5C 00 - FF 01 M143 1E8E 00 - FF 00
M094 1E5D 00 - FF 00 M144 1E8F 00 - FF 00
M095 1E5E 00 - FF 00 M145 1E90 00 - FF 00
M096 1E5F 00 - FF 00 M146 1E91 00 - FF 00
M097 1E60 00 - FF 00 M147 1E92 00 - FF 00
M098 1E61 00 - FF 00 M148 1E93 00 - FF 00
M099 1E62 00 - FF 00 M149 1E94 00 - FF 00
M100 1E63 00 - FF 00 M150 1E95 00 - FF 00
M101 1E64 00 - FF 00 M151 1E96 00 - FF 00
M102 1E65 00 - FF 00 M152 1E97 00 - FF 00
M103 1E66 00 - FF 00 M153 1E98 00 - FF 00
M104 1E67 00 - FF 00 M154 1E99 00 - FF 00
M105 1E68 00 - FF 00 M155 1E9A 00 - FF 01
M106 1E69 00 - FF 00 M156 1E9B 00 - FF 00
M107 1E6A 00 - FF 02 M157 1E9C 00 - FF 03
M108 1E6B 00 - FF 00 M158 1E9D 00 - FF 00
M109 1E6C 00 - FF 00 M159 1E9E 00 - FF 00
M110 1E6D 00 - FF 00 M160 1E9F 00 - FF 00
M111 1E6E 00 - FF 00 M161 1EA0 00 - FF 00
M112 1E6F 00 - FF 00 M162 1EA1 00 - FF 00
M113 1E70 00 - FF 00 M163 1EA2 00 - FF 01
M114 1E71 00 - FF 00 M164 1EA3 00 - FF 00
M115 1E72 00 - FF 00 M165 1EA4 00 - FF 00
M116 1E73 00 - FF 00 M166 1EA5 00 - FF 00
M117 1E74 00 - FF 00 M167 1EA6 00 - FF 00
M118 1E75 00 - FF 00 M168 1EA7 00 - FF 00
M119 1E76 00 - FF 00 M169 1EA8 00 - FF 00
M120 1E77 00 - FF 00 M170 1EA9 00 - FF 00
M121 1E78 00 - FF 03 M171 1EAA 00 - FF 00
M122 1E79 00 - FF 00 M172 1EAB 00 - FF 00

(No.YA337)1-35
Item No. Item Variable range Setting value Item No. Item Variable range Setting value
M173 1EAC 00 - FF 09 M205 1ECC 00 - FF 02
M174 1EAD 00 - FF 00 M206 1ECD 00 - FF 00
M175 1EAE 00 - FF 00 M207 1ECE 00 - FF 00
M176 1EAF 00 - FF 00 M208 1ECF 00 - FF 00
M177 1EB0 00 - FF 0A M209 1ED0 00 - FF 00
M178 1EB1 00 - FF 00 M210 1ED1 00 - FF 00
M179 1EB2 00 - FF 01 M211 1ED2 00 - FF 00
M180 1EB3 00 - FF 00 M212 1ED3 00 - FF 00
M181 1EB4 00 - FF 00 M213 1ED4 00 - FF 00
M182 1EB5 00 - FF 00 M214 1ED5 00 - FF FF
M183 1EB6 00 - FF 00 M215 1ED6 00 - FF 00
M184 1EB7 00 - FF 00 M216 1ED7 00 - FF 00
M185 1EB8 00 - FF 00 M217 1ED8 00 - FF 00
M186 1EB9 00 - FF 00 M218 1ED9 00 - FF 00
M187 1EBA 00 - FF 00 M219 1EDA 00 - FF 00
M188 1EBB 00 - FF 00 M220 1EDB 00 - FF 00
M189 1EBC 00 - FF 00 M221 1EDC 00 - FF 00
M190 1EBD 00 - FF 00 M222 1EDD 00 - FF 00
M191 1EBE 00 - FF 00 M223 1EDE 00 - FF 00
M192 1EBF 00 - FF 00 M224 1EDF 00 - FF 00
M193 1EC0 00 - FF 00
4.6.4 DRIVE SYSTEM SETTING (Fixed values)
M194 1EC1 00 - FF 00
M195 1EC2 00 - FF 00 Item No. Item Variable range Setting value
M196 1EC3 00 - FF 00 F001 DD 000 - 001 000
M197 1EC4 00 - FF 00 F002 RAM REF 000 - 001 000
M198 1EC5 00 - FF 00 4.6.5 NOT USED (Fixed values)
M199 1EC6 00 - FF 00
Item No. Item Variable range Setting value
M200 1EC7 00 - FF 00
D001 RESREV 000 - 255 002
M201 1EC8 00 - FF 00
M202 1EC9 00 - FF 00 4.6.6 NOT USED (Fixed values)
M203 1ECA 00 - FF 00 Item No. Item Variable range Setting value
M204 1ECB 00 - FF 00 Z001 RESREV 000 - 255 002

4.7 ADJUSTMENT PROCEDURE

4.7.1 FOCUS
Measuring
Item Test point Adjustment part Description
instrument
LENS FOCUS Hexagon FOCUS knob (1) Remove the SPEAKER GRILL and CENTER
wrench [PROJECTION LENS] PANEL.
(2.5mm) (2) Display the MENU screen.
(3) Loosen the focus lock screw.
(4) Adjust the FOCUS knob so that the center
Projection lens
screen may become the best focus.
(5) Fix the focus lock screw by using the Hexagon
wrench.
• On this occasion, hold the FOCUS knob with
your left hand.
FOCUS Focus lock (6) Confirm the whole focus of the best screen.
knob screw (7) Install the CENTER PANEL and SPEAKER
GRILL.

1-36 (No.YA337)
4.7.2 DRIVE CIRCUIT
Measuring
Item Test point Adjustment part Description
instrument
DRIVE Remote [9.RGB BOX PATTERN] (1) Set to "0 minutes" using the [SLEEP TIMER]
CONVERGENCE control unit key.
(2) Press the [VIDEO STATUS] key and
Vertical RGB box pattern Horizontal RGB box pattern [DISPLAY] key simultaneously, to enter the
SERVICE MODE.
(3) Press the [9] key, to select "RGB BOX
PATTERN MODE" from the SERVICE MODE.
(4) Set the adjustment color mode to "R" to set the
red color adjustment mode.
(5) At Horizontal RGB box pattern, adjust the top
edge position as same or less than 0.5 pixel
hight as green.
(6) At Vertical RGB box pattern, adjust the right
edge position as same or less than 0.5 pixel
hight as green.
R (7) Set the adjustment color mode to "B" to set the
blue color adjustment mode.
(8) At Horizontal RGB box pattern, adjust the top
Adjustment color
edge position as same or less than 0.5 pixel
hight as green.
(9) At Vertical RGB box pattern, adjust the right
edge position as same or less than 0.5 pixel
hight as green.
(10) Check to see that the cross pattern is white. If
the cross pattern is not white, repeat the step
4. to 9. as abobe.
NOTE:
• Green is a fixed. (It can not be removed.)
• With this adjustment mode, the changed data is
written in the MEMORY instantly.
DRIVE CENTER Remote [9.RGB BOX PATTERN] (1) Receive a center cross (or crosshatch) pattern.
POSITION control unit (2) Set to "0 minutes" using the [SLEEP TIMER]
key.
Signal (3) Press the [VIDEO STATUS] key and
generator [DISPLAY] key simultaneously, to enter the
SERVICE MODE.
(B=B") B B" (4) Press the [9] key, to select "RGB BOX
PATTERN MODE" from the SERVICE MODE.
(5) Set the adjustment color mode to "RGB" to set
A
the display position adjustment mode.
(6) Adjust the top and the bottom width to make A
and A" even.
(7) Adjust the left and the right width to make B
A" and B" even.
RGB
NOTE:
• With this adjustment mode, the changed data is
(A=A") Adjustment color written in the MEMORY instantly.

(No.YA337)1-37
4.7.3 VIDEO CIRCUIT
Measuring
Item Test point Adjustment part Description
instrument
WHITE Remote [1.ADJUST] (1) Receive a NTSC 75% all white pattern.
BALANCE control unit S001: R DRIVE (Red drive) (2) Set "VIDEO STATUS" to "STANDARD".
(HIGHLIGHT) S002: G DRIVE (Green drive) (3) Set "ASPECT" to "FULL".
Signal S003: B DRIVE (Blue drive) (4) Select "COLOR TEMPERATURE" to "LOW".
generator (5) Select "1.ADJUST" from the SERVICE
MODE.
(6) Adjust to keep one of < S001 > (Red drive),
< S002 > (Green drive) or < S003 > (Blue
drive) unchanged, then lower the other two
so that the all-white screen is equally white
throughout.
NOTE:
Set one or more of < S001 >, < S002 >, and
< S003 > to "128".
(7) Check that white balance is properly tracked
from low light to high light. If the white balance
tracking is deviated, adjust to correct it.
(8) Press the [MUTING] key to memoirze the set
value.

4.7.4 MTS CIRCUIT

Measuring
Item Test point Adjustment part Description
instrument
MTS INPUT Remote [1.ADJUST] (1) Receive the any broadcast.
LEVEL control unit T001: IN LEVEL (2) Select "1.ADJUST" from the SERVICE
MODE.
(3) Verify that the < T001 > (IN LEVEL) is set at its
initial setting value.
(4) Press the [MUTING] key to memorize the set
value.
MTS TV audio L OUT [1.ADJUST] (1) Input the stereo L signal (300Hz) from the TV
SEPARATION multiplex R OUT T002: LOW SEP audio multiplex signal generator to the antenna
signal T003: HI SEP terminal.
generator (2) Connect an oscilloscope to L OUT pin of the
AUDIO OUT, and display one cycle portion of
Oscilloscope the 300Hz signal.
(3) Change the connection of the oscilloscope to
Remote R OUT pin of the AUDIO OUT, and enlarge the
control unit voltage axis.
(4) Select "1.ADJUST" from the SERVICE
MODE.
L-Channel R-Channel (5) Set the initial setting value of the < T002 >
signal waveform crosstalk portion (LOW SEP).
(6) Adjust the < T002 > so that the stroke element
Minimum
of the 300Hz signal will become minimum.
(7) Change the signal to 3kHz, and similarly
1 cycle adjust the < T003> (HI SEP).
(8) Press the [MUTING] key to memorize the set
value.

1-38 (No.YA337)
 SECTION 5
TROUBLESHOOTING
5.1 SELF CHECK FEATURE 5.1.5 POINTS TO NOTE WHEN USING THE SELF CHECK
5.1.1 OUTLINE FEATURE
This unit comes with the "Self check" feature, which checks the In addition to circuit failures (abnormal operation), the following
operational state of the circuit and displays/saves it during cases may also be diagnosed as "Abnormal" and displayed and
failure.Diagnosis is performed when power is turned on, and counted as "NG".
information input to the main microcomputer is monitored at all (1) Temporary defective transmissions across circuits due to
time.Diagnosis is displayed in 2 ways via screen display and LED pulse interruptions
flashes. Failure detection is based on input state of I2C bus and (2) Misalignment in the on/off timing of power for I2C bus
the various control lines connected to the main microcomputer. (VCC) when turning on/off the main power.
Diagnosis may be impeded if a large number of items are
5.1.2 HOW TO ENTER THE SELF CHECK MODE displayed as "NG". As such, start Self check check only after 3
Before entering the Self check Display mode, confirm that the seconds in the case of receivers and 5 seconds in the case of
setting of TV/CATV SW of the REMOTE CONTROL UNIT is at panels upon turning on the power. If recurrences are expected,
the "TV" side and the setting of VCR/DVD SW is at the "VCR" ensure to clear (reset) the failure history and record the new
side. If the switches have not been properly set, you cannot enter diagnosis reults.
the Self check Display mode.
(1) Set to "0 minutes" using the [SLEEP TIMER] key. SERVICE MENU SCREEN
(2) While "0 minutes" is displayed, press the [VIDEO STATUS]
key and [DISPLAY] key simultaneously, then enter the SERVICE MENU
service mode. 1. ADJUST
2. SELF CHECK
(3) Press the [2] key (SELF CHECK) before the service mode 3. I2C STOP
screen disappears.
(4) Press the [SLEEP TIMER] key to enter Page 2 of the SELF
CHECK MODE.
• When the [RETURN+] key pressed, the first page
change screen.
NOTE:
When a number key other than the [2] key is pressed in
the SERVICE MENU SCREEN, the other relevant SELF CHECK MODE SCREEN (Page 1)
screen may be displayed.
This is not used in the SELF CHECK. Press the [MENU]
key to return to the SERVICE MENU SCREEN. LOB 0 FAN 0
AUD 0

5.1.3 HOW TO EXIT THE SELF CHECK MODE ANA 9 DIG 9

0000 0
TO SAVE FAILURE HISTORY: 0

Turn off the power by unplugging the AC power cord plug when
in the Self check display mode.

TO CLEAR (RESET) FAILURE HISTORY:

Turn off the power by pressing the [POWER] key on the remote
Item Failure history
control unit when in the Self check display mode.

5.1.4 FAILURE HISTORY

Failure history can be counted up to 9 times for each item. When
the number exceeds 9, display will remain as 9. Failure history SELF CHECK MODE SCREEN (Page 2)
will be stored in the memory unless it has been deleted.
NOTE: TMP 0 L 1 0
L 2 0 DDT 0
Only SYNC (with/without sync signals) will be neither counted FAN 0 L C 0
nor stored. IRS 0

Item Failure history

Fig.1

(No.YA337)1-39
5.1.6 DETAILS
Self check is performed for the following items:
< Page 1 of screen >
Diagnosis
Detection item Display Detection content Detection timing
signal (line)
Low bias line short LOB Detection of the low bias line(5V/9V/12V) short. LB_PRO Detection starts 3 seconds after
protection Q9821, Q9831, Q9861 [POWER PWB] the power is turned on. If error
continues between 200ms the
power is turned off.
Fan lock FAN Not used ---- ----
Audio AUD Not used ---- ----
Devices on the ANALOG ANA Confirmation of reply of ACK signal which uses SDA If it checks whenever I2C
PWB I2C communication. communication is performed and
IC101, IC102, IC281, IC381, IC601, IC606, no reply of ACK signal an error
IC061, TU001 [ANALOG PWB] will be counted.
Devices on the DIGITAL DIG Confirmation of reply of ACK signal which uses SDA If it checks whenever I2C
PWB I2C communication. communication is performed and
IC6401, IC8831 [DIGITAL PWB] no reply of ACK signal an error
will be counted.
< Page 2 of screen >
Diagnosis
Detection item Display Detection content Detection timing
signal (line)
Temp. sensor TMP Confirmation of the abnormal inner cabinet TXD It will count if the serial
temperature. (53°C) communication from a DD
IC2001 [THERMO PWB] MICOM is always supervised and
an error occurs.
Lamp does not light up L1 Confirm that the lamp dose not light up. TXD It will count if the serial
CNBCT [DRIVE PWB] communication from a DD
MICOM is always supervised and
an error occurs.
Lamp goes out L2 Confirm that the lamp dose not goes out. TXD It will count if the serial
CNBCT [DRIVE PWB] communication from a DD
MICOM is always supervised and
an error occurs.
Abnormal DD CPU DDT Confirmation of the serial communication error TXD It will count if the serial
circuit between DRIVE PWB and DIGITAL PWB. communication error is error
IC3701 [DRIVE PWB] occurs.
Fan lock FAN Confirmation of the lock signals outputting the TXD It will count if the serial
operation(circuit) status of the cooling fan. communication from a DD
IC8005 [DRIVE PWB] MICOM is always supervised and
an error occurs.
Lamp cover open LC Confirmation of the interlock switch status for the TXD It will count if the serial
lamp cover. communication from a DD
S0861 [LAMP COVER SW PWB] MICOM is always supervised and
an error occurs.
Abnormal of optical iris IRS Confirmation of the abnormal optical iris TXD It will count if the serial
operation. communication from a DD
IC5005 [IRIS PWB] MICOM is always supervised and
an error occurs.

1-40 (No.YA337)
5.1.7 DISPLAY METHOD WHEN RASTER IS NOT AVAILABLE
In a state where a display screen does not appear due to the failure of this unit, the POWER LED (blue) and LAMP/PROGRAM LED
(orange) can be flushing and display a trouble mode.
The factors in case the power is forcibly shut down at the time of failure are memorized and those are displayed.
LED flash cycle

Check item Contents Classifications LAMP/

POWER LED
PROGRAM LED
(BLUE)
(ORANGE)
Fan lock (stop) and MAIN CPU detects the command of the Fan lock (stop)
CABLE CARD error for and CABLE CARD error which ATSC TUNER MODULE
1 --- 2 sec interval
ATSC tuner has detected.
IC7601 [DIGITAL PWB]
Low bias line short Detection of the low bias line(5V/9V/12V) short.
2 --- 1 sec interval
protection Q9821, Q9831, Q9861 [POWER PWB]
Lamp cover open Detection of the interlock switch status for the lamp
cover. (H = Abnormal) 3 0.1 sec interval Simultaneously
S0861 [LAMP COVER SW PWB]
Lamp goes out Detection of lamp return (LAMP_RTN) signals output
depending on the status of the lamp supply electric
current monitored constantly within the lamp ballast unit. 6 0.1 sec interval Simultaneously
(H = Off)
CNBCT [DRIVE PWB]
Lamp does not light up Detection of lamp return (LAMP_RTN) signals output
depending on the status of the lamp supply electric
current monitored constantly within the lamp ballast unit. 6 0.1 sec interval Simultaneously
(H = Off)
CNBCT [DRIVE PWB]
Fan lock (stop) for Detection of LOCK signals outputting the operation
optical system (circuit) status of the cooling fan. (H=Abnormal) 4 0.5 sec interval Alternately
IC8005 [DRIVE PWB]
Abnormal DD CPU Detection of serial communication error between MAIN
circuit DRIVE PWB and RECEIVER PWB. 5 0.5 sec interval Alternately
IC3701 [DRIVE PWB]
Abnormal D-ILA Detection of abnormal inner cabinet temperature. (53°C)
7 0.5 sec interval Alternately
DEVICE temperature IC2001 [THERMO PWB]
EXPLANATION ON ACTION
If NG is detected on an item being diagnosed, turn off the power on this unit. As soon as the power goes off, turn on and off POWER
LED and LAMP LED immediately. After the power is shut down, it becomes impossible to turn on the power until the power cable
is either plugged in or unplugged from the AC outlet.
• When the error of [1] or [2] occur, [3], [4], [5], [6], [7] are no longer recognized.

(No.YA337)1-41
Victor Company of Japan, Limited
ILA Display Category 12, 3-chome, Moriya-cho, Kanagawa-ku, Yokohama-city, Kanagawa-prefecture, 221-8528, Japan

(No.YA337)
Printed in Japan
VPT