Brother Compal Galaxie Sewing Machine Instruction Manual

all
- gu
SERVICE MANUAL FOR COMPUTERIZED SEWING MACHINE
"COMPAL GALAXIE"
ide
All manuals and user guides at all-guidesbox.com

•
I sb
.... I '-
I
I•
1o
""\ :=1 x.c
••••••••• •• •• --
1-
\... Y
�
I
I DD om
\ J
GENERAL INFORM ATION SYMBOLS USED ARE:
Th1s service manual is compiled for repa1ring service of
t l
COMPUTERIZED SEWING MACHINE "COMPAL GALAXIE"
(Factory code #114-870). Move the part as this way (one way)
Use this manual with Parts Catalogue (H3030294) for
+
fault f1ndmgs when you make a repair.
Th1s machine IS manufactured based on the up-to-dated Move the part as this way (both way)
product specifications at the time of this issue. but there
may be changes of specifications for improvements.
T
Contact manufacturer or local sales company for such
Move the part to its highest or lowest

changes.
position
Brother industries. Ltd.
i
Nagoya.Japan
Set the clearance as indicated
'
1
. . .
I. Principal mechanism ........................................... ....................................................................................
11. D1sassembl1ng & Reassembling ......... . .

.. ........... ............ . 7
111.
......................................... ....... .....................
How to adjust mechanical elements ........................................................................ .............................. 2 9

IV. How to adjust electric elements .. .
.............
.
.................... .......... . .
........ ......... 57
.............. . ............................
CAUTION
1 Always use rubber glove when handling printed circuit board and do not touch the metal portion of printed circuit
.
board w1th bare hands.

2. Keep the human body earthed in order to avoid generating static electricity.
3. Pack printed circuit board w1th alumin1um f01l and avo1d impact on it when keeping or transporting.
4. Do not touch or damage on the metal portion of printed circuit board with screw driver or any other tools even
dunng repainng.
I. PRINCIPAL MECHANISMS
1. MECHANICAL CHART
Balance wheel
Eccentuc counter
weoght
Thread take-up lever assembly

Needle bar supporter ---r-±::t=fi-Ji!f'ij't{'"f"L

Needle bar crank ---"1
-------��fl/=�
Needle bar crank rod
Needle bar clamp --� Clutch mechanosm
Needle bar +-t-;;r-+11---;----Linear actuator
Verucal feed Lower shah Horozontal feed Horozontal feed Lower timong pulley
roller shah regulaung mechanism
-1 -
2 . POWER TRANSMISSION CHART
(A) Gene ra ting mechan ism o f needle bar, thread (B) Movemen ts o f feed dog and shuttle hook
take-up lever and zigzag movemen ts
@
.::: -- (\.
1-----....�
00 �
®

CD
® Balance wheel
@
Balanoe whot
o
tl
Feed regula1or
shah
-2-
3. ELECTRONIC PARTS ARRANGEMENT CHART
Sub-pronted corcuot Bobbin wonder swotch
Ne.ctle POI+Iton
(0ownt IAChCit+ng
lED
Buttonhole (BHI SWitCh
Transformer
Junction for foot controller
Sode cutter swotch Feed dog swotch Cord reel unot Speaker Common pronted circuot board
-3-
all
4. CONTROL SYSTEM BY MICRO-COMPUTER
The micro-computer being used in Compal Galaxie is 8-bit computer fabricated on a single chip using N-MOS (N
-
channel silicon gate MOS process) in 40 pins dual-in-line package with built in 4 K byte mask ROM. 96 byte RAM.
gu
oscillator. timer and 1/0 port. Moreover 1 28K bit mask ROM and 1 6 K bit RAM are expanded on external CPU. All
function of this machine are fully controlled by this micro-computer.
ide
<CONTROL SYSTEM CHART>

sb
tPotenhOi'l'letet)
Foo t com roller
Ceram• c
O S C III ai O f
CPU
o Speed volume
I
x.c
ROM (4K byte) II RAM (96 byte) I
(Other switches)
Star!/stop sw•tch.
R everse SWitCh.
Needle pos•tton
SWitCh.
(Other sensors)
S•de·cutter
detecr.ng swuch.
Bobbin Winder switch
Presser loot pos•t•on
(Dtsplay de v•cel
Pattern dtsplay
LED.
Manual d•splay
LED.
om
Panern select•on Need le pos•tlon
7 segments LED
detecung sw•tch.
button. Feed dog pOSit•on ( UP/DOWNI LED.
Manual st•tch length
Manual s titc h w1dth

detecting SWitch.
control sw•tch. Buttonhole lever
pos•flon detecttng
control sw•tch, SWitCh.
Ten �eys. Buttonhole SWitch.
Program star! key.
Joint �ev
Pattern d•splay
Program end key. change sw•tch
Foot conrroller
Tw•n needle key tack SWitCh
- 4 -
6. THE FUNCTION OF MICRO-COMPUTER (MAL-WARNING VOICE)
CPU be1ng used in this machine i s supervising the k1nd of selected pattern. position of presser foot. feed dog and
buttonhole lever. state of bobbin-winding. Start/stop switch. reverse switch. etc. If the customer operates the
machine erroneously. the error 1s pointed out by mal-warning vo1ce.
The output of voice made by voice synthetic system is PARCOR way which cons1sts of 2 pes. of P-MOS LSI. One i s mask
ROM which stores information digitally analysed for the output voice. of which memory capacity is 1 28K bit. The other
1s acting synthesiS of the voice according to the information from former ROM and CPU output. The mal-warning voice
contains 1 0 messages i n total which are as follows:
1 . Please lower presser foot lever.
2. Please change position of red knob to right to raise feed dog.

3. Please change position of red knob t o left to lower feed dog.
4. Please lower blue lever.
5 . Please raise blue lever.
6 . Reverse stitch cannot be obtained using this pattern.
7. Memory capacity full. Please check instructton book.
8. Please check instruction book.
9 . Th1s pattern combination is not acceptable. Refer to instruction book.
1 0 . Please use a foot controller.
- 5 -
6. MAIN MOTOR CONTROL
A mam motor for sewing machine IS requ1red to have stable revolution from low speed to h1gh speed against load
fluctuatiOn and temperature change. To fully comply with th1s requ1rement. th1s Compal Galaxie IS adopt1ng low
voltage D.C. motor and PWM ( Pulse W1dth Modulation) by transistors.
7. UNEAR ACTUATOR CONTROL (PATTERN GENERATING DEVICE)
(LINEAR ACTUATOR CONTROL BLOCK CHART)

0/A t0ogllfi/An•logl
swoteh
Pattern selectoon Needle bar movong
Drovong corcuot
�onwnt� devoce
Ooflerentoator
CPU
Orovong corcuot Feed regulatong devoc
- 6 -
11. DISASSEMBLING 8r. REASSEMBLING
1. Outer parts .
...................................................................... .......................... . ............ . ..
. .......................... .. ....
8
2 . Cord reel unit .................................................................................. ......................... ................................... 24
3. Printed circuit boards ..
.................... . .
.......... . . . . . . . . . ...................................... . . . .. .
............. ............ 25 .. .. ..... .. .....
4 . Lead wires ....................................... ..................... ............................................................. . . . . . . . ................... 26

5 . Transparency display plate ........................................................................................................................ 27
- 7 -
1. OUTER PARTS
1 . Raise pressure regulating lever and remove face plate by loosening a screw.
2. Remove bobbm wmder cover by loosening a screw.
3 . Remove front cover by loosening three screws.
4. Remove bed cover by loosening two screws.
5. Remove extension plate by l ooseni ng two screws.
6. Remove manual regulator cover by using screw driver.
7. Remove plug case by loosening a screw.

- 8 -
f®
o m ��I;;]J� <:==:::::-' ��
---o=--::::
x . c
b o
e s
u i d
-l g l
a
Arm base plate
-9-
8. Remove stop nng then remove zigzag connecting link.
9. Loosen a screw on eccentric counter we1ght.
10. Lower pressure regulating lever.
1 1. & 1 2 . Remove pressure regulating mechanism by loosening two screws.

-10-
13 Remove power supply base plate cover.
14 Dtsconnect power supply swttch
connector A and transformer
connector B.
- 11 -
1 5. Remove plug case by loosenmg screw.
1 6. Remove cord reel unet by looseneng three screws.

I
I
I
I
t
I
tl11
I
I
I
I
X
- 1 2-
1 7. Loosen a screw.
1 8. Loosen a screw.
19 . Remove a eccentric shaft from lower shaft holder (Right ).
20. Remove feed mechantsm untt by loosening five screws.
I
--
--•
1
I
I
I
I
J,
I I
@
l
I I I
�I
+
I I Stud plate I
®
@
� �
® @11
- 13 -
2 1.
22.-a all
Remove ztgzag connecting lever by loosentng a stud screw.
Remove stop nng then remove ztgzag connecting ltnk. as done at step 8.
23
-b
-c
-d
-
Remove transformer by loosentng two screws.
gu
Remove ftxtng plate by loosentng a screw.
Remove supporttng plate by loosentng a screw
Remove ltnear actuator by loosentng two screws.
ide Ztgzag connecttng lever

Ztgzag connecttng hnk
sb Transformer
o
0 x.c
Ltnear actuator
om
Fuung plate
- 14 -
Reassembling
24. Determine the pos1tion to f1t feed mechan1sm unit by a pm, of which diameter IS 6 mm.
25. Fit feed mechanism unit by using five screws.
2 6. Change the pos1tion of red knob to left to lower feed dog and make sure the clearance between stud plate and
vertical arm IS more than 0. 5 mm.
2 7. Tighten the stud plate by a screw.
28. Insert the eccentric shaft into lower shaft holder (A1ght).
29. T1ghten tentatively.
Stud plate
Lower shalt holder (Left)
I
I
i I �@ I
@
@� 6
A.
- 15 -
30. Meet the convex portions of linear actuator gear and feed regulator gear to face each other then trghten i n two
screws making sure the clearance between both gears is 0.0 3 "' 0.04 mm.
31.-a Fit the zigzag connecting l i n k to vertical arm by a stud screw.
-b Attach supporting plate to the linear actuator.
-c Attach fixing plate onto supporting plate i n a screw making the lower part of the fixing plate hold the right
bushtng of lower shaft holder.
-d Tighten the supporting plate by a screw.
-e Fix transformer. Zogzag connecting lever

nsf orme r
lonear acruator
Feed
regulat�ng gear Foxong plate
-16-
32. Fit the pressure mechanism unit to vertical arm incerting eccentric counter weight into upper shaft.
3 3. Tighten pressure mechanism unit in two screws. At that time tighten upper screw slightly and after adjusting the
top of needle drop to the center of needle hole. tighten two screws securely.
34. Assemble zigzag connecting link to zigzag connecting lever and attach stop ring together with thermoplaStiC
washer.
3 5. Tighten a screw tentatively.
- 17 -
36. Lower the needle until 1ts lowest pos1t1on by turmng balance wheel.
37. Turn the balance wheel so that the base line of lower t1mmg pulley IS nght under then make sure the clearance
between eccentric counter we1ght and upper shaft bushmg IS 0 - 0.02 mm.
38. T1ghten the screw of eccentriC counter we1ght securel y.
Eccenuoc coun1er weoghl @'
,.-,
,--..,

1---o�o2mm
-18-
39. loosen a screw.
40. lower the needle from •ts highest pos1t1on by 2 1 .4 mm turnmg balance wheel forward .
o m l01H�- J
Arm port1on
"
'
a
; c
I
Needle bar stand ---

.
:I :
x I
: l 21 4 mm
b
11i---Need
le bar
b o
a : The h1ghest pos1t1on of needle bar
b . The ume thal brake 1S released
b =a+ 21.4 mm
s
(The brake os released at th1s po.nll
e
4 2 . Tighten the screw.
43 .
d
4 1 . Make sure the clearance between feed regulator and brake gum is 0 - 0.05 mm by turning eccentric shaft.
i
Ra1se the needle from its lowest position by 1 5.2 mm turnmg balance wheel forwa rd. (Brake operation startmg
u
pomt)
4 4. Make sure the brake IS properly operated to feed regulator.
-l g l
a
- 19 -
Needle bar On the way

h1gh est pomt needle bar lowenng
Brake gum
Screw
c =a+ 15.2 mm
a Measurement on the needle bar h1ghest po1nt
•
- 20 -
45. PositiOn rotation shutter so that it can cross rotat1on sensor when needle IS pos1t1oned at 22.9 mm lower than its
h1ghest position. Then pos1t1on N. P. shutter so that 1t can cross N. P. sensor when the clearance between thread
take-up lever and the nb of thread guard IS about 0 mm. (Th1s 1s temporary adJUStment and make f1nal adJUStment
later. Refer to page 34.)
'
l/0 rl_1 I
I
a
I I
I I d
I I 22 9 mm
I I
I I
I I
Posotron of rotatron shutter
The measure·
ment should be
Omm
Posrtton of N P shutter
- 21-
46 . Connect mam power sw1tch connector A and transformer connector B .
47. Fit the power supply c1rcu1t board .
48. Fit cord reel unit by t1ghtemng three screws.
49. Fit plug case by t1ghten1ng a screw.

I
I
I
I
I
I
t
t
- 22 -
50. Fit plug case by tightening a screw.
5 1 . Fit extension plate with two screws.
52. Fit bed cover with two screws.
5 3. Fit front cover with two screws.
54. Fit bobbin winder then tighten a screw.
55. Fit a face plate with a screw.
56. Fit a manual stitch control switch cover.
A rm base p late
- 23 -
2. CORD REEL UNIT
(How 10
all
remove)
- gu
1. Loosen 3 screws and remove those screws holdmg cord
reel base so that it does not turn. Turn cord reel base
counterclockwise about 4 - 5 times until it is free from the
tension of spiral spring.
2. Remove cord reel wheel from cord reel cover.
(How to fit)
3. Put cord reel washer on cord reel wheel. ide

4. Put cord reel wheel in cord reel case.
5. Make sure that cord goes as far as possible by moving the
notching lever toward outside using screw driver.
6. Turn cord reel base counterclockwise about 4 5 times
sb
o
-
and hold it not to turn clockwise in the tension of spiral

spring.
7. Fit cord reel base with 3 screws.
x.c
om
- 24 -
3. REMOVING PRINTED CIRCUIT BOARDS
St art / atop SWit ch un1 1

I
•
•
P & reverse sew. ng t c. e U ed "'ST /Sfr1 connectOf
Stan ltl O
•
W t C h connector
SuttonhoN fctUtd ·� H " ) S
i
•
• Um.pc oon&c:tor
•
8unonhote lever te l l� '"' BHL "') sw.tch connect Ot
Pres.ser fool tcaUecl · pf:

- J S'Mtcl't conn ecto r
Aottt 1on /Needle pos•hon senso r calted

c NPSEN! connec to1
Li mp SWi tch fct lltd -LPSW connector

)
r I C 1Uil0f conn ector
Leogth lt ntl
OII I� JIIt<l - Fo- 1

G
S.de c u Ut t Ccalt td - s ew ) connec tor
floG connoc 1or
T.cno..g ene rtt or ( Cf lltd I G

· ) connec'tor
Soeake r con ntct Of
- 25 -
4. LEAD WIRES ARRANGEMENT
·� ��T��r��!iiillll��ii�

.,
•a
- 26 -
5. REMOVING TRANSPARENCY DISPlAY PlATE
(The order of di..uembling)

1 . Loosen a screw then remove a stop rsng and a spring.
2 . Remove pattern change lever.
3. Loosen 2 screws.
4. Remove transparency display plate.
(The order of reaaaembling)
Proceed sn reverse order of disassembling. Make sure to f1t
sprsng as Illustrated.
- 27 -
Fitting position of micro-switch
1 . Make sure the micro-switch actuator i s in l1ne with micro
switch body. Make sure LED is lighted when mi cro-switch
lead wire IS connected t o printed circuit board and pattern
Pattern dtsplay change lever
change lever is moved to right.
2. Make sure micro-switch actuator is not contacted with I
�--�1-Mtcro-swttch
-- actuator
pattern change lever when pattern change lever is moved
to left. Make sure LED continues to light to left direction
when mi cro-switch 1s connected to printed circuit board
and pattern change lever 1s moved to left then the pattern T o be
selection switch (left) is keeping depressed .

Mtcro-swttch
Pattern dtsplay change lever
Some clearance
- 28 -
Ill. HOW TO ADJUST THE MECHANICAL ELEMENTS
1 . Position of shuttle hook
·········· · · · · · · · · · · · · · · · · · · ··········································· ···················································
30
2 . Height of needle bar ........ ........................................................................................................................ 31
o m
3. Bobbi n case holder bracket ............................... ............. ....... .................................................................
4 . Height of presser bar .............. ................................................. ..... ...........................................................
5 . He1gh t of feed dog ....................... ....... ....................... ............................................................... ............... 33
32
32
. c
6. Position of rotation shutter & N.P. (needle position) shutter ..................................... .........................
7. Brake timing for feed regu lator ..................................................................................... ............ .............
8. Tensio n of motor belt ......................................................................................... ............. ............. ...........
x 34
36
37
................ .................................................................... .......................................... 8
9 . Tension of tim1ng belt 3

o
1 0. R.P. M. of main motor ............................................................................................................................... 39
11. Needle stopping speed ...... .......... ..... .............................................. ............ .................................... . . . . ..... 41
b
12. Centering of the needle ....... ......................................................................... ........................................... 42
s
1 3. Settrng of the maximum needle swing ..................................... ..................
........................................... 43
1 4 . Forward feeding at straight stitches ... ..................................... ........................ .................................. . . . . 44
e
1 5 . Length of forward and reverse stitches for super automatiC patterns ............................................... 45
1 7. Upper tension dial . .

1 8 . T hread tension release
....
.........
........
.................... ... ..............

..
......................... .............................. .. . .
.....................
............................................................
u .
d
1 6 . Position of buttonhol e sw1tch lever .................. ............... ................... ... ................................................ 46
i . ........
..................
48
.......... ................
49
1 9 . Side-cutter adjustme nt (lock lever posi ti on) ................................................................ ........................ . 50
...
20. Side-cutter adjustment (lower & upper kn 1ves) ................. ................................. ..........................
..... 51
21. Side-cutter adJUStment (upper knife does not work) ............................................... .......... ........... .......
l
23. N eed e threader
..
22. Side-cutter adjustment (attachrng guide plate A & B) ............................... ................ ........................
-l g
................................................... ............................................................... ......................
24. Needle threader (exchange) ............................................................................................. .......................

52
53
54
55
l
2 5 . Needle threader (checki ng the hook position) ................. ......... ............................................................
2 6 . Needle threader (adjustment of hook position) .................................... ................................................
a
56
57
- 29 -
1. POSITION OF SHUTTLE HOOK
STANDARD
When z1gzag stitch is selected and the width IS set at its maximum position.
1. When needle raises from its lowest pos1tion by 4.0-4.3 mm. the hook point should meet with the side of the needle
at left needle movement.
2. The clearance between the hook and needle IS less than 0.1 mm and never touch each other.
ADJUSTMENT
1. Set the machine at z1gzag pattern.
2 . Set zigzag width at its maximum position.
3. Loosen three screws.

4. Adjust the hook to achieve above two standard.
5. T1ghten the screws. .
NOTE
Make sure two standard are ach1eved if you loosen the screws.
(2/
r,,
(i)
J
�l--, - -- �
--- .i'�I---,IJ
00 I .,
, ,.
• De
o
Atmomo n
0tl I ' b I
�edtt bar
Less than
:- lit'I 0. 1 mm
-
c{o....•
1 1 and
I 1
;t,
3 mm
I o
The lowest pos1t1on of needle bar

The measurement when hook po1nt
a
b
meet w1th lhe s1de of needle 4 0-4.3 mm
la-4 o-a-4. 3)
-30-
2 . HEIGHT OF NEEDLE BAR
STANDARD
When the zigzag st1tch IS selected and the w1dth 1s set at 1ts max1mum position.
1. The clearance between the upper top of needle eye and bottom top of hook IS 0.4- 1.0 mm when needle and hook
meet at left needle POSitiOn.
ADJUSTMENT
1. Set the machme at z1gzag pattern.
2 . Set the zigzag w1dth at its max1mum pos1tion and seek the POSitton that needle meets with hook point by turn1ng the
balance wheel.
3. Loosen the screw.
4 . Move the needle bar up or down to obtam correct postt1on.

5. T1ghten the screw.
NOTE
Care should be taken when you adJuSt the needle bar. the needle bar eastly turns and 1f tightened mcorrectly, 1t m1ght
be caused the trouble of twm needle sewmg.
.!.
CD �
J
I
• OCJI I IIll'
11
OCJ
- 31 -
3. BOBBIN CASE HOLDER BRACKET 4. HEIGHT OF PRESSER BAR
STANDARD STANDARD
1 . The clearance between the bracket and hook 1s 0.5- 0 7 1 . The clearance between presser foot and needle plate 1s 6 .0
mm. -6.5 mm.
ADJUSTMENT ADJUSTMENT
1. Select zigzag pattern and set Z1gzag width at ··o··. 1 . Ra1se presser foot lever.
2 . Loosen two screws. 2 . Loosen screw.
3 Adjust the pos111on of bracket (reght to left or back and 3. AdjuSt the height of presser bar.
forth). 4. T1ghten the screw
4 T1ghten screws. NOTE

Make sure the presser foot and feed dog are en l1ne.
<D J
l
A ! •I
0 c:::J I I,,,.
Oo
0 .5-0 7 mm
-32-
5. HEIGHT OF FEED DOG
STANDARD
1. The feed dog is higher than needle plate by 0.9 - 1 . 1 mm
when drop feed IS set at up posit1on and 1t reaches its
h1ghest position.
2. The clearance between the feed dog and needle plate 1s
more than 0. 3 mm (below) when drop feed IS set at down
position and feed dog reaches its h1ghest pos1tion.
ADJUSTMENT
1 . Set the drop feed at up position.
2. Turn the balance wheel and seek the posit1on that feed dog
reaches 1ts highest poSitiOn. Loosen the set screw and turn
--=kt
the stud. Tighten the set screw.
....
0 9-U mm
_J;r·,··
-33-
all
6. POSITION OF ROTATION SHUTTER & N.P. (NEEDLE POSITION) SHUTTER
-
STANDARD
1. D1sappear the LED md1cat1ng ··w (horizontal) when needle 1 s reached at the position of 22.9 mm lower than 1ts
gu
h1ghest pos111on by turnmg balance wheel at test mode.
2. In case that needle is set at 1ts up position. the top of needle IS stopped at the pos1t1on of 8 mm upper than needle
plate also thread take-up lever is stopped at the position of 1 4 ± 1 mm upper than thread tension bar.
ADJUSTMENT
2.
set a test mode.
Set ide
1. Turn the power supply sw1tch on w1th keep1ng both manual StitCh length/w1dth control sw1tches depressed to be
the needle at the positiOn of 22.9 mm lower than 11s highest position by turnmg balance wheel.

sb
3. Loosen a hexagon socket screw of rotat1on shutter
4. Turn the rotat1on shutter forth slowly and seek the pos1t1on that the LED ''H'' disappears.
5. Tighten the screw.
o
6. Start sewing and stop 11 by usmg start/stop switch.
7. Loosen a hexagon socket screw of N. P shutt er.
x.c
8. Seek the correct stop pos1tion (h1ghest pos1t1on) of thread take-up lever to meet with above standard by turnmg
N.P. shulter forth or back.
·1n case that the shulter turns too soon. thread take-up lever stops before 11 reaches to 1ts h1ghest pos1 110n.
In case that the shuller turns too late. thread take-up lever stops after 11 IS over at 1ts h1ghest pos1t10n .
1 0. Check 1f the adJUStment meets w1th above standard when the needle stops at its up position.
om
-34-
22.9 mm
N. P . sensor
l!'lllZZ:��!'lZZZlZ.i!'lZZZlZ.i
R otatoon sen sor
\ Needle lowest
Rotatoon shutter
poont
Upper face of
needle plate
- 35 -
7. BRAKE TIMING FOR FEED REGULATOR
STANDARD
When balance wheel i s turned forward. feed regulator is released from the brake at the position that needle i s lowered
by 21.4 mm from its highest pos1tion and brake operates again from the position that the need le 1s raised at 15.2 m m
until its h1ghest posit1on through its lowest position.
ADJUSTMENT
1. Lower the needle by 21.4 m m from its highest position by turnmg balance wheel.
2. Loosen a screw.
3. Adjust the clearance between feed regulator and brake-gum to be 0 "' 0.05 mm by turning eccentric shaft.

5. Raise the needle by 15.2 mm from its lowest position through 1ts lowest position .
6. Make sure that the brake IS properly operated on feed regulator.
On the way
needle bar is ra1s1ng
Needle bar On the way
h1ghest pomt needle bar IS lowerm gh.,.......---,-�-.
c
c =a+ 15.2 mm
a . Needle bar h1ghest po1nt
-36-
8. TENSION OF MOTOR BELT
STANDARD
There should be some slacks (4 - 6 mm) when the motor belt is JUSt pushed (about 200 g pressure.)
ADJUSTMENT
1. Loosen two screws.
2. Adjust belt tension by moving motor holder to meet with
above standard.
3. Tighten the screws. I
I
I
---c:l
Change che car·
wears off aboul 3

bon brushwhen 11
mm
CD®
l1
-37 -
9. TENSION OF TIMING BELT
STANDARD
There should be some slacks ( 3- 5 mm) when the timing
belt is just pushed (abotu 200 g pressure.)
ADJUSTMENT
1 . Loosen a screw.
2. Adjust the posit1on o f idle pulley to meet with above
standard.

- 38 -
10. R.P.M. OF MAIN MOTOR
STANDARD
Speed
o m <D
I
<D.@.®
•I
I I1 1 1 1�11
1 1 Ill1 I
I 111111111g111111111 I
Control
Lever I c • • •
R.P.M .
• •
100-1 20R. P.M.

•
x . 800-85 0R .P. M. (STRAIGHT) 700-75 0 R.P. M . (ZIGZAG)

380-420R.P. M . (MEMORY & PROGRAM PATIERNS)
CAUTION o
As each volumes are locked by paint. turn them slightly to the direction of rotation and not give any pressure to the
b
direction of thrust. After adjustment. make sure t o be again locked by paint.
ADJUSTMENT
1 . Set a machine at test mode. e s
2. Set the speed control lever at its leftest position (lowest speed position ) .
1 00- 1 20R.P.M.
d
3. Start the machine and turn the volume of VR 1 clockwise or counterclockwise so that number of rotat1on should be
i
4. Set the speed control lever at its rightest position (h1ghest speed position) and select the straight stitch.
u
5 . Start the machine and turn the volume VR2 clockwise or counterclockwise so that numbers of rotat1on should be
800-850R. P.M.
6. Select zigzag st itch.
-l g
7. Start the machine and turn the volume VR3 clockwise or counterclockwise so that numbers of rotation should be
700- 75 0R.P. M.
8. Change to the memory mode and select one of memory patterns. (No. 4 7-67). l
a
9 . Start the machine and turn the volume VR4 clockwise or counterclockw1se so that numbers of rotat1on should be
380-4 20R. P.M.
- 39 -
-
<D
�- VR9 VR10
t() D 00�, i<=i��VR2
VR6 VR7
31\eil �1831
::[i]
0 000§• !c=l�@vRJ
&� �� == �VRB VR5 eVR4

D
•
� (t}vRt
\�
c:a CI
NOTE
1 . Each speed s never exceed to the standard.
2. The sewi ng speed is indicated by 2 digits in digita l display window.
Ex. "1 2" means "1 20R .P.M:·.
- 40 -
11. NEEDLE STOPPING SPEED
STANDARD
When needle stops at 1ts up pOSitiOn. needle threader can be usable and pass the thread to thread take-up lever �aslly.
ADJUSTMENT
1 . Set the machine at test mode.
2. Set the sew1ng speed at 1 40R.P.M. by movmg speed control lever.
3. Turn the volume VR5 clockw1se until LED 1nd1cating (vertical) w1ll be lighted.
4. Turn the volume VR5 counterclockwise unt1l the LED w1ll disappear.
))
I)
J �:tD
J
. .
.•
.:-, , ,
_) ®
-�
-41-
12. CENTERING OF THE NEEDLE
STANDARD
1. Needle should drop at the canter of needle hole when z1gzag pattern is selected w1th its mmimum stitch width.
ADJUSTMENT
1. Set a machine at test mode.
2 . Select the zigzag st1tch.
3. Turn the volume VR10 clockwise or counterclockw1se so that needle should drop at the center of needle hole.

J
& ij
,..----'i----
<Z>
•
��
-42-
13. SETTING OF THE MAXIMUM NEEDLE SWING
STANDARD
1. Needle enters the needle hole balanced when zigzag stitch IS selected w1th ItS max1mum st1tch w1dth.
ADJUSTMENT
1. Set a machme at test mode.
2. Select z1gzag stitch
3. Set the z1gzag w1dth at 1ts max1mum pos1110n .
4. Turn the volume VR9 clockw1se o r counterclockw1se so that max1mum z1gzag w1dth should be 6.8"" 7.0 mm
VR9
@'
J
® �•
6 B-7.0 mm
-43 -
all
14. FORWARD FEEDING AT STRAIGHT STITCHES
-
STANDARD
1 . There should be no feeding when stitch length is set at its minimum position.
ADJUSTMENT
1. Set a machine at test mode. gu
2 . When setting at stra1ght st1tch. 1 1 stitches are sewn 1n 24 mm.
ide
2. Set the speed control lever at 1ts maximum position.
3. Turn the volume VR-8 clockwise or counterclockwise so that no feeding is obtainable in sewing on paper when
stitch length IS set at its minimum position. (The paper is not fed at least 5 seconds.)
4. Set the machme at pattern (} .

Maximum stitch length should be more than 4.5 mm.
VR6 sb
5. Start th1s pattern on paper until it is finished and adjust to meet with above standard 2 by turnmg volume VR6 .
G
(j) --
))
o @(}
x.c •
om
_)cv TT
JJ<mm
@'
l [ Jji;l
o 1 1 slltches
-44-
15. LENGTH OF FORWARD AND REVERSE STITCHES FOR SUPER AUTOMATIC
PATTERNS
STANDARD
Make sure to obtain proper length of both forward and reverse stitches to make fine pattern.
ADJUSTMENT
1 . Change to memory mode by moving pattern change lever to right.
2. Input following pattern numbers to sew as EPS . No. 04 + N o. 1 5 + No. 18.
.. .
3. Set the length fine adjustmg volume on the right side of machine to be honzontal direction.
4. Depress the start/stop button to sew sample.
5. Turn the volume VR7 clockwise or counterclockwise so that reverse stitch meets with forward stitch.
• In case that longer reverse stitch is required Turn the volume clockwise.
· · · · · ·
In case that shorter reverse stitch is required Turn the volume counterclockwise.
· · · · ·
§;0
•
� �- -
-r - �+
==
- 45 -
16. POSITION OF BUTTONHOLE SWITCH LEVER
STANDARD
1 . When buttonhole lever {Blue lever) and presser foot lever
are lowered. BHO touches with BH 1.
2. The legs of buttonhole should be d1ameter of button plus Bunonhole sw•tch body
2. 5 mm.
ADJUSTMENT
1. Select buttonhole pattern. 0 mm-·-""��-- 0 m
m
2. Fit the buttonhole foot and push the top port1on of rt
/1\ BH 1
....L..W"
... v
backward as far as 1t will go.

3. Loosen a screw.
4. In case that the legs are shorter than the standard. bend the �""
f.-f-.
BH 1 to be far from BHO. BH2�
In case that the legs are longer than the standard. bend the
BH2 to be near BHO . BHO ®
5 . Tighten the screw.
<D u
•
O.Smm
- 46 -
17. UPPER TENSION DIAL
STANDARD
1. The clearance between two discs should be 0 - 0.3 mm
when presser foot i s lowered and tension dial is set at 0.

2. Spnng i s touched with spring holder and the top of thread
release plate begins to depress on the tension disc B. when
presser foot is lowered and tension dial rs set at 8.
ADJUSTMENT
1. Set upper tension dial at 0.
2. Lower the presser foot lever.
3. Loosen two screws.

4. Adjust the position of thread tension bracket to meet wrth
above standard 1.
5. Tighten the screws.
6. Set upper tension dial at 8.
7. Loosen a hexagon socket screw.
8. Adjust the position of spring holder to meet with above
Screw
standard 2.
-47-
18. THREAD TENSION RELEASE
STANDARD
The clearance between two discs should be more than 0.5
mm when presser foot IS ra1sed and tens1on d1al IS set at 9.
ADJUSTMENT
1 . Set upper tens1on d1al at 9 and raise the presser foot lever.
2. AdJuSt the position of thread tens1on release B to meet w1th
above standard.
3. T1ghten the screw and check 1f the clearance between two
d•scs IS more than 0.5 mm by moving presser foot lever u p

and down.
-48-
19. SIDE-CUTTER ADJUSTMENT (LOCK LEVER POSITION)
STANDARD
When the lock lever IS fully pushed down (2.5- 3.0 kgs). the lower part of lock lever should be pos1t10ned w1thm the
red mark.
ADJUSTMENT
o m
1 . Loosen two screws and take out the upper plate.
3. Loosen a screw. . c
2. Take out bracket case and attach the s1de-cutter on the tubular arm.
4. Turn the eccentnc stud with screw dnver and adJuSt the clearance between the lower s1de of lock lever and Side
cutter to be 3 5 mm. x

6. Attach the bracket cover and check agam.
b o
e s
u i d
Lock lever
-l g l
a
- 49 -
20. SIDE-CUTTER ADJSUTMENT (LOWER 8t UPPER KNIVES)
STANDARD
1. When Side-cutter IS out of machine and upper kn1fe holder 5. Move the holder downward and loosen a set screw. Adjust
IS at h1ghest pos1t1on. both knives meet each other by 0. 7- the clearance between guide axis and holder be 0 mm and
1.2 mm. then tighten the set screw.
2. Lower and upper kmves b1te each other by 1.5- 2.5 mm
when needle bar moves to its lowest pos1110n.
ADJUSTMENT
1. Remove bracket case by loosening two screws.
2. Keeping holder at highest position. adJUSt lower and upper

kn1ves to meet each other by about 1 .0 mm and set upper
kn1fe temporanly.
3. Attach the side-cutter to tubular arm and set needle bar at
1ts lowest posit1on makmg sure they meet each other by 1.5
- 2.5 mm.
4. Remove side-cutter from machine and f1rmly tighten the
upper knife with securing holder.
""' <O� f
Upper knofe holder
- 50 -
21. SIDE-CUTTER ADJUSTMENT (UPPER KNIFE DOES NOT WORK)
Upper kn1fe should work when 1t IS set to machane.

STANDARD
ADJUSTMENT
1. Attach the s1de-cutter to tubular arm and set the needle bar at 1ts h1ghest pos1t1on.
2 Loosen a screw.
3. By mov1ng the holder up and down. seek the pos1tion that the pan 1s fitted 1nto gu1de plate.
4 . T1ghten the screw.
Pon
Upper knofe holder
- 51 -
22. SIDE-CUTTER AD JUSTMETN (ATTACHING GUIDE PLATE A & B)
STANDARD
The clearance between gUide plate A and upper knife should be 0 mm.
ADJUSTMENT
1 . S e t the holder at 1ts h1ghest pos111on.
2. Loosen the screws on gu1de plate A & B and adJUSt the clearance between the gu1de plate A and upper kn1fe to beO.
3. T1ghten the screw A & B

Guode plate B
®'
Omm
- 52 -
23. NEEDLE THREADER
1. Needle threader accept o nly circle marked needle and thread combmations.
2. marked combination is not recommended since it might lead to the breakage of needle threader imperfect
•
performance.
3. Lower the presser foot when you use needle threader.
4. Do not use needle threader when you use twin needle.
5 . Nylon transparent thread is applicable in needle # 1 4
- 1 6.
6. Do not turn the balance wheel when you use needle threader.
7. Do not touch needle threader when machine i s running.
8 . Needle should be located above needle plate for more than 8 mm for threading.
9. Needle threader does not work when you use the side-cutter.
�
N
#30
X
#50
X
#60
X
#80 #100 #120
#9 0 0 0
#1 1 X X 0 0 0 .
#14 X 0 0 0 . .
#16 . 0 0 . . .
#18 . . . . . .
- 53 -
all
24. NEEDLE THREADER (EXCHANGE)
-
How to exchange needle threader
gu
1 . Remove needle and lower the presser foot.
2 . Push down needle threader to take out
3 Place new one so that gu1de IS 1mmed1ately under the gu1de
p1n.
ide
4. Push needle threader all the way up so that gUide 1s placed
10 the pm.

sb
o x.c
om
- 54 -
26. NEEDLE THREADER (CHECKING THE HOOK POSITION)
STANDARD
1 . The clearance between the top of hook and the top of
needle eye 1s 0.
2. Threadmg is capable when needle IS located h1gher than 8
mm from the needle plate.
CHECK
Case A
Hook pos1t10n 1s too h1gh.
Case B
Hook pos1t1on IS too low. (Hook enters needle eye but tt

catches bottom part of needle eye.)
Top of
hook
A B
Needle
Hook
X X
- 55 -
26. NEEDLE THREADER (ADJUSTMENT OF HOOK POSITION)
ADJUSTMENT
Case A (Hook pomt 1S too h1gh)
1 Remove face plate and loosen the screw.
2. Adjust needle threader slightly down and check the clearance between the top of hook and top of needle eye 1 s zero.
3. Check 1f part ®and part 1s m line
@
Case B (Hook pomt 1s too low)
Adjust needle threader slightly up and check the clearance between the top of hook and top of needle eye 1s zero.
Note
In case part ® and part @ IS not m I me. hook does not work. AdjuSt needle threader by loosenmg the screw.

+-
� - Needle bar
'-::::::�
::t: :1
.Jr-t- Needle rhreader
X X
pos1110n sener
Frg. 1 Frg 2
- 56 -
IV. HOW TO ADJUST ELECTRONIC ELEMENTS
1.
Power supp ly ······································· · · · ················ · · · · ···············
··············································· ··················
59
2. When power supply is on . z1gzag st1tch is not indicated by LED ············································ ·············
63
3. P attern selection ···························•····· ······························ · · · · · ·····················
· · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · · ············•···
63
3-1 . P anern d1splay is not moved when pattern selection switch is depressed ···································
64
3-2. Memory mode is not selected when pattern display change lever is moved to right ··········•······
65
3-3. Other patterns than the ones for Side-cutter are selected when side-cutter is attached ············
66
4. Main motor
····································································
·································· ············· · · · · · · ························
67
4- 1 . Main moto r does not rotate when start/stop switch is depressed .... . .......... .... ........ ... .. ............. ... 68
4- 2 . Machine stops with warning buzzer in a second after it runs ....... . ....
. ......................... ... . . ....... .. .. .. 69
4-3 . Out of speed control ····························· · · · · · ·············· · · · · · ················· ···································· ·················
69
5 . Main motor stop ··········································· · · · · · ············ · · · · · · · · · · · · · · · · · · ···························································
70
5 - 1 . Main motor does not stop ························· · · · · · · · · ····························································
·····················
71
5-2. Needle stop position (UP/DOWN) i s incorrect ··················································
· · · · · · · · · · · · · · · · · · · ···········
71
6 . Pattern generation ················· ························································ ·············································· ···············
72
6-1 . Zigzag width is not correct · · · · · · · · · · · · ············· · · · · · · ························· ································
·························
73
6-2. Stitch length is not correct ······························· ······················································
····························
74
6 - 3. Buttonhole is not obtained ....... . . .. ............ . ........................... ... ........... ..... ........ . ................ ..... ............ . 76
7. Mal-warning voice is not made ·······························································
················· · · · · · · · · · · · · · · · · · · · · ············
77
- 57 -
CONNECTORS TABLE
Start/stop swotch u not

Start/stop & reve rse stotch connector
Buu onhole swotch connec tor
Lamp connector
Maon pronted corcu o t board
Buttonhole lever swotch connector
otatoon/ needle posotoon connector

Lamp swotch connector
Wodth lo near actuator connector
Length lonear actuator connector
Sode-cuner swotch connector
Feed dog switch connector
ache-generator connector
Maon motor connector
Speaker connector
Sub-pr.nted corcuot board
Speaker connector
- 58 -
-trHow to adjust electric elements
1. POWER SUPPLV
o m Secondary voltage of transformer (P13)
Terminals AC Voltage Notes
AC
Power
source x . c 1-7
4-7
9- 1 1
about 1 5 . 5V
1 5 . 5V
about 1 3 .0V
for circu1t &
main motor
for lamp
• Cord reel unit 8t Power supply switch

1 . Take out cord reel unit from machine.
b o Transfurmer
transformer connector B.
3. Turn the power supply sw1tch on.
e s
2. Take out power supply SWitCh connector A and
4. Measure the resistance between terminal 1 & 3

on connector A.
1 u i d
....::: I
No
R (Resistance) s: 1 fi? Exchange power supply switch
Yes1
1 . Insert power supplv plug to outlet.
2. Measure the voltage between terminal 1 & 3 on
connector B .
-l g l
-= AC
_l
Power supply voltage No
iExchange cord reel unitl
a
T
Ves
- 59 -
• Transformer (Secondary Voltage)
1 . Connect transformer connector Band take out

circuit board cover.
Fit cord reel unit to the machine.
2. Take out face plate and front cover.
3. D1sconnect transformer connector P1 3 from
common c�rcu1t board.
4. Insert power supply plug to outlet and turn the
power supply switch on.
5. Measure the AC voltage between terminal 1 &

7. 4 & 7 and 9 & 1 1 on the connector 1 3 .
No
Exchange transformer
Yes
1
Che ck other portions
1 . Turn the power supply switch off and connect

connector P1 3.
2. Turn the power supply sw1tch on.
3. Measure DC+ 1 7. 5V and DC-1 7. 5V. (Refer to
printed circuit board diagram on page BO.)
- 60 -
No
1 . Turn the power supply switch off.
2 . Disconnect main motor connector P 1 S and linear
actuator connector PS & P9 from c1rcu1t board .
• Internal resiStance
Yes
"=>
- _ �Refer @
--:
Main motor connector P 1 8 1 - 2 about 2.00
on page 62.
Linear actuator connector PS & P9 1 -2 about 8. 50
Disconnect connector P6 (for rotat1on & N.P.

sensor). PS (for linear actuator) and P9 (for linear
actuator) from mam circuit board. Yes
Exchange main motor

and/or linear actuator
Connect connector P6
to mam circu1t board.
Exchange mam CirCUit board units.
__,_
.__ Y""
e"'"
s
__ ___.� Exchange linear actuator
- 61 -
1 . R between P3 connector (for lamp) & GND = oo?
R between P7 connector (for lamp switch) & GND = oo?
No 2. R of P3 connector = 34-380?
3. R of P7 connector at lamp switch on = 10?
R of P7 connector at lamp switch off = oo?

Yes
Normal
No
Exchange lamp. lamp switch

or lead wire.
Exchange main c1rcuit
board units.
..
Note: .. R stands for resistance.
.. GND.. stands for frame ground (lt IS connected to .O.V)
. .
.
. oo·· stands for infinite resistance.
-
82 -
2. WHEN POWER SUPPLY IS ON, ZIGZAG STITCH IS NOT INDICATED BY LED
Check 1f the power supply IS normal.

No 1. Refer to item 1 "POWER SUPPLY" on page 59.
Exchange mam ClfCUit board un1ts.

3. PATTERN SELECTION
0 Flow chart 1 (Movement of machme when pattern selecting sw1tch is depressed)
Patternos depressed?
sWitCh
selectong A
Shifting to utility mode

Revolution stop
Yes
No�------�
Pforattern selectmg wothon 4 patterns
sode-cuner
-�========� � ��
att�er n dlever
Pchange
� p�
o s�
� R ig�
v =:::::::��
la=: ht
�
-
,- - _ _ _ _-- - _ _ _ _ _ __ __ __ �
Pat l e rn select o n g o ul o f m em o�
patterns
- 63 -
all
3-1. Pattern display ia not moved when pattern selection switch ia depressed
1.
2.
-
Turn the power supply switch off.
gu
D1sconnect connector P1 from c1rcu1t
board.
3. Measure A between terminal 4 and 5 on P-1
ide
R between termmal 4 and 7 on P-1
No
Exchange start/stop switch unit

Disconnect connector P 1 4
sb
Measure A between terminal 1 and 2 on P 1 4
No o x.c Exchange foot controller jack
Exchange main c1rcuit board umts

om
- 64 -
3-2. Memory mode is not selected when pattern display change lever is moved to right
1 . D1sconnect connector P1 0 for s1de-cuner Check the f1tt1ng position of

SWitCh. m1cro-sw1tch. (Refer to page
28)
2. Turn power supply sw1tch on and shift
pattern display change lever to nght.
-c:=:::::� ��
Memor y� ��
mode IS��=======---------��
selected? Y�
e�
s --�
.
J\ Exchange side-cutter sw1tch.
No
1 . D1sconnect connector P1 7 for m1cro
switch and shift pattern display change
lever to right.
2. Measure R between terminal 1 & 2 on Pl 7 .
No
R :ai 1 n J Exchange m1cro sw1tch
'--
-- -- -- -- -- -- -- )
Yes
( Exchange main circuit board units.
-65-
3-3. Other patterns than the ones for side-cutter are selected when side-cutter is attached
1. Attach side-cutter to the tubular arm.

2. Remove connector P 1 0.
3. Measure R between terminal 1 & 2 on P 1 0

No
R :ii lfl J
\
Exchange Side-cutter sw1tch )
Yesl
Exchange main circuit board units.
- 66 -
4. MAIN MOTOR
Flow chart 2 (Movement of mach1ne when start/stop button or foot controller is depressed)
OFF
Motor does not st art

Motor do
e s not stan. No
Mal-warnmg voice
Motor is revolutmg at setting speed?

Mal-warning voice
Motor 1s revolut1ng at set

point?
No The revolution is stopped and warnmg

is made by buzzer for 5 seconds.
- 67 -
4-1. Main motor does not rotate when start/stop switch is depressed
Warnong os made by buzzer?

No Disconnect connector and measure the
P1
resistance between terminal 4 & 7 on P 1
Yes while start/stop button is depressed.
Turn the balance wheel both clockwise and
counterclockwise.
Yes
Too much torque
AdtuSl mechanocal
® poruons.

Exchange main circuit
board units.
Disconnect connector P 1 8. Measure the resistance

between two terminals on P 1 8.
= about 20
R
Yes Exchange main motor
No
-
68 -
4-2. Machine stops with warning buzzer in a second after it runs
Make the check as same as ® on page 68.

o m Rotation & N.P. shutter
are properly pos111oned'
No Adjust the rotation/N.P. shutter.
. c
(Refer to page 34
Yes
Exchange N.P. circuit board.
x
4-3. Out of speed control b o

e s
onnector P 1 2 IS p r OI)t!rly No Re-connect
connected?
Yes
Disconnect connector P1 2 and measure the resistance u i d
between terminal 1 & 2 on P12.
Yes
365n?
-l g
No Exchange main motor
l
a
- 69 -
5. MAIN MOTOR STOP
0 Flow chart 3 (movement when stopping machine)
Set the machine at its lowest speed.
Yes

No
No
No
0 The relat1on of posit1on between N.P. sensor & N.P. shutter. (Refer to page 34)
When N.P. sensor 1s blocked by N.P. shutter Needle-up position
· · · · • · ·
When N.P. sensor •s opened from N.P. shutter Needle-down position

· · ·
- 70 -
6-1. Main motor does not stop
Adjust R.P.M. at the lowest speed by turmng VR1 .

(Refer to page 39)
Adjust needle stop speed. (Refter to page 41)
Yes Finish
Exchange main circuit board unets

6-2. Needle stop position (UP/DOWN) is incorrect
Turn balance wheel by hand.

Too much to rque.
AdJUSI mechamcal
portoons.
Adjust the pos1tion of N.P. shutter. (Refer to page 34)
Ad1ust the lowest speed. (Refer to page 39)

Adjust needle stop speed. (Refer to page 41)
Exchange mam c1rcuit board unets.

- 71 -
6. PATTERN GENERATION
0 Flow chart 4
Honzontal feed link IS

moved.

Needle bar is moved.
0 Timing chart (Needle highest position = 0°)
ij
pos1 t1_
7.io· r·-··:.::"'"
..-
---T
NT-
eed.;,.
;..;
;.. le,;.
·d..;..won..;.. _ 0_
n___ N.P shutter (for detecung needle SlOP POS1t1on)
...,..,.,..,
Non-bloc ,...
k
40" 160° 180°

Needle-up pos1110n pulse Needle-up pos1t1on pulse
W1dth dr�ve
----
81ock
= = ---
--:
:-:
I
1 2 :6 • )
:-:1.'\. eed dr�ve
Non-block
�
2 Rota110n shutter (for detect1ng pattern pulse oulput pos1t1on)
-Lock1ng mechan1sm
I
-
,-- ---
Lock�ng
120"
Non-locking I
260"
''LOCK MECHANISM'' 1s operated to hold honzontal feed link mechanically during fabric is fed.
1 . Horizontal feed link is hold at locked position.
2. Horizontal feed link is free at non-locked position and position of honzontal feed link can be moved by linear
actuator. which means feed volume can be changed.
- 72 -
6-1 Zigzag width is not correct
.
Turn the power supply swttch off and move

needle bar right and left by hand.
===---...:N..:;o:<...__,� AdJUSt rotauon shutter.

(Refer to page 34 & 35)
Disconnect connector PS and measure the restst·

ance between termmal 1 & 2.
No
Exchange linear actuator unit.
Measure the resistance between terminal 3 & 4 on PS

while needle bar is moving.
Yes
No
Exchange linear actuator unit.
Yes
- 73 -
all
6-2. Stitch length is not correct
-
Check following points:
gu
height of feed dog (refer to page 33) . pressure lever. brake
timing for feed regulator (refer to page 36). forward stitch
length (VR6 & VRB. refer to page 44). forward & back stitch
length for super automatic pattern (VR7. refer to page 45).
ide Yes

sb No
o
Disconnect connector P9 and measure the resist
ance between terminal 1 & 2 .
x.c
om
No
Exchange linear actuator unit
Measure the resistance between terminal

3 & 4 while feed regulating mechanism is
operated.
No
Exchange linear actuator unit
- 74 -
0 Flow chart 5 (Buttonhole)
Movement Movement Movement Movement Movement
® @ © @ ®
l
I
rr
I
l
I I
I I
f!
I
-�
)f 11
I I
I I
I I
f!
I
-� -
I I
I
q l
t I
I
f!
I
-� -
- 75 -
6-3. Buttonhole is not obtained
(Different length of nght and left leg)
Let BHSW lever work by hand to make buttonhole.

AdJUSt the posit1on of BH lever. (Refer to page 46)
1 . D1sconnect connector P2.

2 . Measure the resistance between termmal 1
& 2 and 2 & 3 while BH lever is pushed
back.
Exchange BH switch.
Measure the resistance between terminal 1 & 2

and 2 & 3 while BH lever is pushed forth.
Exchange BH switch
Exchange mam circuit board umts.
- 76 -
7. MAL-WARNING VOICE IS NOT MADE
No
Exchange sw1tches or sensors.
01sconnect connector P 1 6. Measure the

res1stance between termmal 1 & 2 on P 1 6.
No
Exchange speaker
Exchange ma.n circu1t board um ts.
- 77 -
Common Pnnted Circuit Board

<Printed Circuit Board>
'tfCAUTION
Take care following points when handling printed circu1t board:
1 . Do not touch the connecting portion of the connector. especially
the pin for the plug with bare hands. for example. could be
generated. causing bad connection.
2. If the surface of the connecting portion is dirty. polish it with
aJco�
Sub- Pnnted Circu1t Board

om
x.c
bo
id es
gu-
all

Brother Compal Galaxie Sewing Machine Instruction Manual

Uploaded by

Copyright:

Available Formats

Brother Compal Galaxie Sewing Machine Instruction Manual

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Brother Compal Galaxie Sewing Machine Instruction Manual

Uploaded by

Copyright:

Available Formats

all

All manuals and user guides at all-guidesbox.com

Th1s service manual is compiled for repa1ring service of

Use this manual with Parts Catalogue (H3030294) for

All manuals and user guides at all-guidesbox.com

11. D1sassembl1ng & Reassembling ......... . .

How to adjust mechanical elements ........................................................................ .............................. 2 9

board w1th bare hands.

Thread take-up lever assembly

Needle bar supporter ---r-±::t=fi-Ji!f'ij't{'"f"L

All manuals and user guides at all-guidesbox.com

Sub-pronted corcuot Bobbin wonder swotch

Buttonhole (BHI SWitCh

Junction for foot controller

All manuals and user guides at all-guidesbox.com

Foo t com roller

Manual s titc h w1dth

2. Please change position of red knob to right to raise feed dog.

7. UNEAR ACTUATOR CONTROL (PATTERN GENERATING DEVICE)

(LINEAR ACTUATOR CONTROL BLOCK CHART)

All manuals and user guides at all-guidesbox.com

Orovong corcuot Feed regulatong devoc

4 . Lead wires ....................................... ..................... ............................................................. . . . . . . . ................... 26

All manuals and user guides at all-guidesbox.com

All manuals and user guides at all-guidesbox.com

All manuals and user guides at all-guidesbox.com

ide Ztgzag connecttng lever

All manuals and user guides at all-guidesbox.com

Lower shalt holder (Left)

All manuals and user guides at all-guidesbox.com

All manuals and user guides at all-guidesbox.com

Needle bar stand ---

All manuals and user guides at all-guidesbox.com

Posotron of rotatron shutter

All manuals and user guides at all-guidesbox.com

All manuals and user guides at all-guidesbox.com

and hold it not to turn clockwise in the tension of spiral

St art / atop SWit ch un1 1

Pres.ser fool tcaUecl · pf:

Aottt 1on /Needle pos•hon senso r calted

Li mp SWi tch fct lltd -LPSW connector

OII I� JIIt<l - Fo- 1

floG connoc 1or

T.cno..g ene rtt or ( Cf lltd I G

Soeake r con ntct Of

All manuals and user guides at all-guidesbox.com

(The order of di..uembling)

All manuals and user guides at all-guidesbox.com

Pattern dtsplay change lever

9 . Tension of tim1ng belt 3

1 7. Upper tension dial . .

.................... ... ..............

24. Needle threader (exchange) ............................................................................................. .......................

All manuals and user guides at all-guidesbox.com

The lowest pos1t1on of needle bar

4 . Move the needle bar up or down to obtam correct postt1on.

All manuals and user guides at all-guidesbox.com

All manuals and user guides at all-guidesbox.com

All manuals and user guides at all-guidesbox.com