The document provides information on calculating the dead and wind loads for a proposed two story apartment building. It includes the unit weights of various building materials, floor finishes, and mechanical equipment. It also includes wind pressure calculations. The summary provides calculations to determine the design base shear, including the total dead load weight, seismic coefficients, and governing minimum and maximum base shear values.
The document provides information on calculating the dead and wind loads for a proposed two story apartment building. It includes the unit weights of various building materials, floor finishes, and mechanical equipment. It also includes wind pressure calculations. The summary provides calculations to determine the design base shear, including the total dead load weight, seismic coefficients, and governing minimum and maximum base shear values.
The document provides information on calculating the dead and wind loads for a proposed two story apartment building. It includes the unit weights of various building materials, floor finishes, and mechanical equipment. It also includes wind pressure calculations. The summary provides calculations to determine the design base shear, including the total dead load weight, seismic coefficients, and governing minimum and maximum base shear values.
The document provides information on calculating the dead and wind loads for a proposed two story apartment building. It includes the unit weights of various building materials, floor finishes, and mechanical equipment. It also includes wind pressure calculations. The summary provides calculations to determine the design base shear, including the total dead load weight, seismic coefficients, and governing minimum and maximum base shear values.
L = 1.64795 kPa B= 8 m Width of Building L= 20 m Length of Building h= 6.75 m Roof Mean Height h= 6 m Height to Roof Beams Adjustment Factor = 1 h= Topographic Factor = 1 Figure 207A.8-1 Page 100
a= 0.8 m 10% of least horizontal dimension
a= 2.7 m 0.4H B
amin = 0.9 m but not less than 4% of horizontal dimension or 0.9m
Used a = 0.9 m Used 2a = 1.8 m Remaining Length Normal To Ridge = 18.2 m
Horizontal Pressures Vertical Pressures Overhangs
Wind Pressures A B C D E F G H EOH GOH 2.53 -0.67 1.69 -0.37 -2.2 -1.53 -1.53 -1.16 -3.08 -2.41
Horizontal Pressures Vertical Pressures Overhangs
Adjusted Wind Pressures A B C D E F G H EOH GOH 2.53 0.67 1.69 0.37 -2.2 -1.53 -1.53 -1.16 -3.08 -2.41
2a L -2a TOTAL Wind Lateral Force = 27.324 1.809 184.548 10.101 223.782 kN
Base Shear = 123.46076 kN Err:508
Engineering Report PROPOSED TWO STOREY Structural Calculation APARTMENT BUILDING
Design Base Shear
Design Parameters No. of Storey 2 Soil Profile Type = D Seimic Zone = 0.4 Rwx = 8.5 Numerical Coefficient for Structural Systems Rwz = 8.5 Numerical Coefficient for Structural Systems Na = 1.5 Near Source Factor (see table) Nv = 2.0 Near Source Factor (see table) Ct = 0.0731 hn = 6.2 I= 1 Importance Factor W = 636.01 Total Weight of Dead Loads Ca = 0.66 Seismic Coefficient (see table) Cv = 1.28 Seismic Coefficient (see table) Ta = Cthn3/4 0.287218 T = 1.3*Ta < Tb 0.373383 Structural Period for Design Dim. of Building Along X = Dim. of Building Along Z = Design of Base Shear Center of Max along X Cx = V = CvIW/RT = 256.5078 kN Total Design Base Shear Center of Mass along Z Cz= Vmax = 2.5CaIW/R = 123.46 kN Total Design Base Shear Shall not Exceed Center of Rigidity along X = Vmin1 = 0.11*CaIW = 46.17 kN Total Design Base Shear Shall not be less than Center of Rigidity along Z = Vmin2 = 0.8ZNvIW/R 47.89 kN Total Design Base Shear Shall not be less than Ex = 0 Governing Base Shear (V) 123.460765 kN Ez = 0
Ft = - Ft = 0.07TV < 0.25V if T is more than 0.7sec, Ft = 0 if T is less than 0.7sec
#REF! Engineering Report PROPOSED TWO STOREY Structural Calculation APARTMENT BUILDING
m m m m m m m m
Torsion-z (kN-m) #REF!
#REF!
#REF!
#REF!
#REF!
#REF! Engineering Report PROPOSED TWO STOREY Structural Calculation
Design Base Shear
Design Parameters No. of Storey 2 Soil Profile Type = D Seimic Zone = 0.4 Rwx = 8.5 Numerical Coefficient for Structural Systems Rwz = 8.5 Numerical Coefficient for Structural Systems Na = 1.5 Near Source Factor (see table) Nv = 2.0 Near Source Factor (see table) Ct = 0.073 hn = 6.2 I= 1 Importance Factor W = 1497.926 Total Weight of Dead Loads Ca = 0.660 Seismic Coefficient (see table) Cv = 1.280 Seismic Coefficient (see table) Ta = Cthn3/4 0.287 T = 1.3*Ta < Tb 0.373 Structural Period for Design Dim. of Building Along X = Dim. of Building Along Z = Design of Base Shear Center of Max along X Cx = V = CvIW/RT = 604.12514 kN Total Design Base Shear Center of Mass along Z Cz= Vmax = 2.5CaIW/R = 290.77 kN Total Design Base Shear Shall not Exceed er of Rigidity along X = Vmin1 = 0.11*CaIW = 108.75 kN Total Design Base Shear Shall not be less than idity along Z = Vmin2 = 0.8ZNvIW/R 112.79 kN Total Design Base Shear Shall not be less than Governing Base Shear (V) 290.77 kN
Ft = - Ft = 0.07TV < 0.25V if T is more than 0.7sec, Ft = 0 if T is less than 0.7sec
