MACHINE DESIGN AND SHOP PRACTICE REFRESHER SET NO.

4
1. A steel bandsaw blade is 0.032 in thick. Find the value of the B. 32.5 psi D. 1.45 psi
bending stress when the blade is passing around a pulley of 20 in 13. An SAE C1040 eyebolt is lifting a 350 lbs block. Determine the
diameter. stress area of the bolt if it is under the Unified Coarse Series
A. 122.33 ksi C. 48 ksi Thread and has an ultimate strength of 67 ksi and yield strength
B. 59 ksi D. 96 ksi of 55 ksi.
2. What is the outside diameter of a hollow shaft replacing a 150 A. 0.3411 𝑖𝑛2 C. 0.1041 𝑖𝑛2
mm diameter solid shaft with equal torsional strength and 50% B. 0.4301 𝑖𝑛2 D. 0.1134 𝑖𝑛2
weight saved? 14. A machine shop fabricates a pair of spur gear, 2.5 module to be
A. 180 mm C. 160 mm mounted on shafts with a centerline distance of 90 mm. The
B. 190 mm D. 170 mm speed required is 3:1. (Use 20° pressure angle). Find the root
3. A 1000 lbs flywheel has a torque capacity of 2600 ft-lb. the speed diameters.
is to be maintained between 100 and 120 rpm. The effect of the A. 24.6 mm and 120.45 m
arms and hub accounts for 10% of the rim weight. Find the mean B. 32.45 mm and 145 .25 mm
diameter of the flywheel. C. 38.75 mm and 128.75 mm
A. 35.36 in C. 38.63 in D. 12.34 mm and 110.45 mm
B. 44.65 in D. 42.78 in 15. The newly installed motor drives a hoist that is use in lifting a 4-
4. A 2000 kg elevator rises from rest in the basement to the fourth ton load at a given distance of 30 ft in 30 seconds. What is the
floor, a distance of 25 m. As it passes the fourth floor, its speed power supplied to the hoist assuming hoist efficiency of 48 %?
is 3 m/s. There is a constant frictional force of 500 N. Calculate A. 42.70 hp C. 14.54 hp
the work done by the lifting mechanism. B. 30.30 hp D. 37.53 hp
A. 487 kJ C. 300 kJ 16. A set screw is necessary to fastened a pulley to a 2 in. shaft while
B. 512 kJ D. 125 kJ transmits 3 Hp and rotates at 150 rpm. Find the torque on the
5. A 6-mm fillet weld 50 mm long carries a steady load of 13,000 N set screw.
lying along the weld. The weld metal has a yield strength of 360 A. 110 ft-lb C. 120 ft-lb
Mpa. Find the value of the factor of safety. B. 105 ft-lb D. 130 ft-lb
A. 3.2 C. 1.45 17. The breaking strength of a steel cable is 20 kN. If one pulls
B. 1.75 D. 2.94 horizontally with this cable, what is the maximum horizontal
6. A double fillet welded joint with parallel fillet weld of 305 mm acceleration with can be given to an 8-metric ton resting on a
length and 10 mm leg is subjected to a tensile force of 1 kN. rough horizontal surface if the coefficient of kinetic friction is
Assuming uniform stress distribution, determine the shear stress 0.15?
in the weld. A. 1.03 m/s2 C. 3.01 m/s2
A. 0.15 MPa C. 0.57 MPa B. 2.05 m/s 2 D. 4.03 m/s2
B. 0.75 MPa D. 0.23 MPa 18. An inclined plane 12 ft long has been used to slide a 250-lb box
7. The element is subjected to the plane stress condition shown up to a loading space that is 7 ft above the ground. If 185 lbf is
(𝜎𝑥 = -200 MPa, 𝜎𝑦 = 140 Mpa, & 𝜏𝑥𝑦 = 70 Mpa). What is the needed for loading the cargo upward, what is the efficiency of
maximum shear stress? the inclined plane for this job?
A. 183.85 MPa C. -213.85 MPa A. 85.48 % C. 82.41 %
B. 153.85 MPa D. -153.85 MPa B. 78.82 % D. 74.52%
8. The element is subjected to the plane stress condition shown 19. A hydraulic press has a pressure inside its cylinder equal to 1.2
(𝜎𝑥 = -200 MPa, 𝜎𝑦 = 140 Mpa, & 𝜏𝑥𝑦 = 70 Mpa). What is the ksi. What is the thickness of the cylinder if its diameter is 10
maximum and minimum normal principal stress? inches and the allowable tensile stress is 2.5 ksi?
A. 234.85 MPa C. -122.85 MPa A. 4.5 in C. 5.2 in
B. 153.85 MPa D. -645.85 MPa B. 3.9 in D. 1.5 in
9. The element is subjected to the plane stress condition shown 20. If the gear has tooth thickness of 0.30 inch and the backlash of
(𝜎𝑥 = -200 MPa, 𝜎𝑦 = 140 Mpa, & 𝜏𝑥𝑦 = 70 Mpa). What is the 0.007 inch, calculate its space width.
orientation of the principal (normal) and shear stress plane A. 0.307 inch C. 0.254 inch
respectively? B. 0.203 inch D. 0.365 inch
A. 𝜃𝑝 = -15.2deg, 𝜃𝑠 = 34.82deg 21. Compute the power to be taken off the driven shaft on an open
B. 𝜃𝑝 = -11.2deg, 𝜃𝑠 = 33.82deg belt drive operated by a driving pulley 76 inches in diameter at
C. 𝜃𝑝 = -21.2deg, 𝜃𝑠 = 33.82deg 200 rpm. Note: the diameter of driven pulley is 32 inches and the
D. 𝜃𝑝 = -11.2deg, 𝜃𝑠 = 35.82deg total tensions on the tight and slack sides are 300 and 100 lbs
10. An 80 cm radius wheel rolls along a flat surface at 4 m/s. If points respectively.
A and B are 90° away from each other, what is the velocity of A A. 20 hp C. 18 hp
when B contacts the ground? B. 24 hp D. 26 hp
A. 3.75 m/s C. 5.65 m/s 22. Calculate the pressure is required to punch a hole 3 in. diameter
B. 2.25 m/s D. 4.24 m/s through a ¼ in. steel plate.
11. A leather belt running at 15 m/s transmits 20 kW to a cast iron A. 60 tons C. 22 tons
B. 30 tons D. 39 tons
pulley rotating at 150 rpm. If the belt density is 968.625 kg/𝑚 3
calculate for the centrifugal stress experience by the belt during 23. Determine the minimum whole depth of spur gear of 14.5°
the run. involute type with diametral pitch of 24 and circular pitch of
0.1309 inch.
A. 2.108 MPa C. 0.218 MPa
B. 0.518 MPa D. 0.812 MPa A. 0.09000 inch C. 0.08879 inch
12. Cast iron pulleys, 4 in. and 20 in. in diameters, are lo transmit 3 B. 0.0899 inch D. 0.086535 inch
hp at 1200 rpm of the smaller pulley, through a single ply oak- 24. What is the elongation of a 1.5 m aluminum bar of modulus of
elasticity 70 Gpa when subjected to a tensile stress of 150 MPa?
tanned leather belt. Calculate the centrifugal stress if the center
to center distance is 10 ft. Note: for leather belt f = 0.30, density A. 4.32 mm C. 1.24 mm
is 0.035 lb/in3. B. 3.21 mm D. 2.34 mm
A. 5.75 psi C. 23 .6 psi
 MACHINE DESIGN AND SHOP PRACTICE REFRESHER SET NO. 4
25. Solve the tooth thickness of a 14.5° spur gear with diametral 39. The newly installed motor drives a hoist that is use in lifting a 4-
pitch of 5. ton load at a given distance of 30 ft in 30 seconds. What is the
A. 0.24352 inch C. 0.31416 inch power supplied to load if the hoist efficiency is 48% and motor
B. 0.24352 inch D. 0.05643 inch efficiency is 90%?
26. Calculate the tooth thickness on the tooth circle of a 20-degree A. 42.7 hp C. 24.54 hp
full depth involute tooth having a circular pitch of 20 mm and B. 30.3 hp D. 14.54 hp
whole depth of tooth at 16 mm. 40. What is the mass of a 120-lbf man is standing in an elevator?
A. 12 mm C. 14mm A. 3.73 lb C. 5.45 lb
B. 10 mm D. 17mm B. 3.73 slugs D. 2.86 slugs
27. What is the chordal thickness at the standard pitch diameter for 41. A vise is equipped with a 1-inch single square thread, with 4
a pinion that has 15 teeth of 3 diametral pitch? threads per inch. The frictional diameter of the collar is 0.5 inch.
A. 0.3255 in C. 0.2342 in The coefficient of friction for both the collar rind threads is 0.20.
B. 0.2375 in D. 0.5226 in How much external torque must be applied to produce a force
28. Determine the Hp lost when a collar is loaded with 2000 lb, of 200 lb against the jaws of the vise?
rotates at 50 rpm, and has a coefficient of friction of 0.15. The A. 39.73 in-lb C. 33.97 in-lb
outside diameter of the collar is 4 inches and the inside diameter B. 36.23 in-lb D. 39.37 in-lb
is 2 inches. 42. In a power screw square threads, the torque required to raise
A. 0.7314 Hp C. 0.3572 Hp the given load is found to be 8800 N-in. Compute the shear stress
B. 0.4713 Hp D. 0.4371 Hp caused by this torque considering that the core diameter of the
29. What is the average time to cut by automatic oxy-acetylene screw is 40 mm.
(machine) crosswise a 4ft. x 8 ft x 4 in thick steel plate given that A. 700 Mpa C. 24.5 ksi
the rate is 9 in/min? B. 350 Mpa D. 10.5 ksi
A. 3.32 min C. 12 min 43. A ball with speed of 20 cm/s rolls off the edge of the table 90 cm
B. 320 sec D. 540 sec high. How long does it take to drop to the ground.
30. A steel tape was used to measure a distance from A to B and A. 0.34 s C. 0.54 s
found out to be 5,368.25 ft at 22°F. Compute the true distance B. 0.43 s D. 0.25 s
between A and B if the tape was a standard 100.00 ft at 68°F and 44. A 10-lb weight is attached to a 1.5-ft cord and is whirled in a
the tape's coefficient of expansion is 0.0000065. vertical circle with an angular velocity of 120 rpm. Compute the
A. 5 366.5 ft C. 5 363.5 ft tension in the cord in the event that the weight is at the bottom
B. 5 348.7 ft D. 2 358.7 ft of the circle.
31. A piece of stock of length 24 inches has taper per foot of ¼ in., A. 73.5 lbf C. 63.5 lbf
compute the diameter of one end given that the smaller end is B. 83.5 lbf D. 53.5 lbf
1.5 inches in diameter. 45. What is the time needed to saw a 5 in wood using a handsaw
A. 1.75 in C. 1.25 in with a cutting rate of 0.010 mm/rev and speed of 200 rpm?
B. 2.0 in D. 2.75 in A. 63.5 min C. 35.2 min
32. A 1.5 in bolt is screwed up tightly in a packed joint. If the B. 52.4 min D. 60.7 min
allowable stress is 12 ksi, calculate its working strength. 46. A pair of spur gears with 2.5 module to be mounted on shafts
A. 10350 lbs C. 12500 lbs with a centerline distance of 90 mm. The speed required is 3:1
B. 20400 lbs D. 15250 lbs and a pressure angle of 20°. Calculate its dedendum distance.
33. How many 5/16 inch holes can be punch in one motion in a steel A. 3.125 mm C. 1.345 mm
plate made of SAE 1010 steel 7/16 inch thick using a force of 55 B. 2.135 mm D. 2.435 mm
tons. The ultimate strength for shear is 50 ksi and use 2 factor of 47. A machine shop fabrication a pair of spur gear, 2.5 module to be
safety mounted on shafts with a centerline distance of 90 mm. The
A. 5.8 C. 5 speed required is 3:1. (Use 20° pressure angle). Find the outside
B. 3.7 D. 6.5 diameters.
34. Compute the speed of the gear mounted on a 52.5 mm diameter A. 50 mm and 140mm
shaft receiving power from a driving motor with 250 Hp. B. 30 mm and 120 mm
A. 2 182 rpm C. 2 071 rpm C. 24 mm and 120 mm
B. 2 265 rpm D. 2 341 rpm D. 13 mm and 130 mm
35. Three extension springs are hooked in series that support a 48. Calculate the tooth thickness of on the tooth circle of a 20-deg
single weight of 100 kg. The first spring is rated at 4 kN/m and full depth involute tooth having a diametral pitch of 5.
the other two springs are rated 6 kN/m each. Determine the A. 0.3142 inch C. 0.4428 inch
equivalent stiffness of the three springs. B. 0.2509 inch D. 0.9734 inch
A. 1.71 kN/m C. 5 kN/m 49. An eyebolt is lifting a block weighing 350 lbs. The eyebolt is of
B. 2.71 kN/m D. 3.71 kN/m SAE C 1040 material with Su = 67 ksi and Sy = 55 ksi what is the
36. What is the speed of the tip of the second hand relative to the stress area (in inches square) of the bolt if it is under the unified
watch if it is 2.5 cm long? coarse series thread?
A. 0.00267 m/s C. 0.00987 m/s A. 1341 C. 0.991
B. 0.10914 m/s D. 0.00197 m/s B. 0.1134 D. 1043
37. If the lowest cutting speed for cast iron is 50 fpm, calculate the 50. The power hacksaw does 120 strokes/min and the feed/stroke is
rpm for machining a cast iron work piece 6 inches in diameter. 0.127 mm. How much is the time need to saw a rectangular
A. 32.5 C. 45.7 magnesium bar 5 in. wide and 2 in. thick if the length of cut is 5
B. 31.8 D. 52.6 in?
38. A 36-tooth pinion turning at 300 rpm drives 120-tooth gear of A. 250 s C. 450 s
14.5° involute full depth pressure angle. Determine the rpm of B. 500 s D. 120 s
the driven gear. 51. If there 440 persons occupying the whole building other than the
A. 60 rpm C. 45 rpm first floor, how many elevators are required?
B. 75 rpm D. 90 rpm A. 2 C. 4
 MACHINE DESIGN AND SHOP PRACTICE REFRESHER SET NO. 4
B. 3 D. 1 rope equivalent to 40 lbf through a distance of 38 ft. Calculate
52. A 900-N man stands on a scale on the floor of an elevator. The the efficiency of the machine used by the mechanic.
scale records the force it exerts on whatever is on it. What is the A. 85 % C. 89.7 %
scale reading if the elevator has an acceleration of 1.2 m/s 2 B. 94.7 % D. 95.4 %
down? 65. The newly installed motor drives a hoist that is use in lifting a 4-
A. 870 N C. 640 N ton load at a given distance of 30 ft in 30 seconds. What is the
B. 790 N D. 820 N power supplied to the motor assuming hoist and motor
53. Calculate the average time to cut by oxy-acetylene (automatic efficiencies are 48 % and 87% respectively.
machine) lengthwise a 5ft. x 10 ft 4 in thick steel plate. Oxy A. 42.70 hp C. 76.43 hp
acetylene cuts 25.4 cm of length every minute. B. 34.83 hp D. 65.95 hp
A. 540 s C. 720 s 66. By applying a constant torque to a grindstone, its flywheel
B. 320 s D. 450 s reaches an angular velocity of 1100 rpm in 10 seconds. Assuming
54. Find the angle of contact on the small pulley for a belt drive with it stunted from rest. Calculate its angular acceleration if the
a 72-in center distance if the pulley diameters are 6 inches and grindstone’s moment of inertia is equal to 1.2 x 10 3 kg-m2.
12 inches respectively. A. 10.54 rad/s2 C. 11.52 rad/s2
A. 175.22 deg. C. 125.7 deg. B. 12.54 rad/s 2 D. 9.54 rad/s2
B. 145.45 deg. D. 152.2 deg. 67. A 120-lbf man is standing in an elevator. What is the force on the
55. A pulley system used in a machine shop with an ideal mechanical man's feet when the elevator stand still?
advantage of 5 requires a force of 12 N to lift a load of 45 N. A. 80 lbf C. 100 lbf
Compute the actual mechanical advantage of the pulley system. B. 120 lbf D. 90 lbf
A. 3.75 C. 135 68. A 900-N man stands on a scale on the floor of an elevator. The
B. 0.267 D. 1.067 scale records the force it exerts on whatever is on it. What is the
56. A single square thread power screw is to raise a load of 70 kN. scale reading if the elevator has an acceleration of 1.2 m/s 2 up?
The screw has a major diameter of 36 mm and a pitch of 6 mm. A. 828.5 N C. 0
The coefficient of thread friction and collar friction are 0.13 and B. 1010.1 N D. 940 N
0.10 respectively. If the collar mean diameter is 90 mm and the 69. By applying a constant torque to a grindstone, the flywheel
screw turns at 60rpm, find the combined efficiency of screw and reaches an angular velocity of 1100 rpm in 10 seconds. With the
collar. moment of inertia equivalent to 1.2 x 10 -3 kg-m2, find the torque
A. 13.4% C. 15.5 % if it started from rest.
B. 14.5% D. 12.5 % A. 0.210 N-m C. 0.138 N-m
57. How fast is the drill turning if it penetrates 100 mm every minute B. 0.124 N-m D. 0.329 N-m
considering a steel drill with a feed of 0.005 in/rev.? 70. The moment of inertia of a 12-cm grinding disc is 0.03 kg.m2.
A. 1520 rpm C. 787 rpm What is the angular acceleration if the 15 N force is applied to
B. 620 rpm D. 505 rpm the periphery of the disk.
58. If the weight of 7” ø x 5’ long SAE 1030 shaking is 297.4 kg, then A. 50 rad/s2 C. 60 rad/s2
what will be the weight of chromium SAE 51416 of same size? B. 40 rad/s2 D. 80 rad/s2
A. 344.4 lbs C. 578.9 lbs 71. What is the moment of inertia of a 6-kg wheel if the radius of
B. 655.8 lbs D. 877.2 lbs gyration is 30 cm?
59. Find the horsepower required to drive a power screw lifting a A. 0.32 kg-m2 C. 0.54 kg-m2
load of 4000 lbs. A 2 and 1/2 inches double square thread with B. 0.42 kg-m2 D. 0.74 kg-m2
two threads/in is to be used. The friction radius of the collar is 2 72. What is the frequency of revolution of the second hand which is
inches and the coefficients of friction are 0.1 for the threads and 2.5 cm long?
0.15 for the collar. The velocity of the nut is 10 ft/min A. 0.017 rev/s C. 0.208 rev/s
A. 5.245 HP C. 4.395 HP B. 0.109 rev/s D. 0.098 rev/s
B. 2.453 HP D. 3.342 HP 73. Calculate the rotational KE of a 20-kg wheel rotating at 5 rev/s if
60. A pulley system used in a machine shop with an ideal mechanical the radius of gyration of the wheel is 0.18 m?
advantage (IMA) of 5 requires a force of 12 N to lift a load of 45N. A. 320 J C. 140 J
What is the efficiency of the pulley system? B. 400 J D. 120 J
A. 0.75 C. 135 74. A small motor delivers 0.25 hp when its shaft is turning at 1200
B. 0.267 D. 1.067 rev/min. Compute the torque.
61. A flywheel weighing 457 kg has radius of 375 mm. How much A. 1.48 ft-lb C. 3.24 ft-lb
energy in N -m does the flywheel loss from 3.0 rev/sec to 2.8 B. 1484 N-mm D. 2310 N-mm
rev/sec? 75. The shaft having an interference fit has a maximum diameter of
A. 1542 N-m C. 120 N-m 4.0 cm and a nominal diameter of 3.990 cut. What is the
B. 1472 N-m D. 40 N-m minimum diameter of the shaft of its upper and lower deviations
62. A mechanic uses a pulley system to raise a 120-lbf load 12 ft from are 0.006 and 0.005 cm respectively?
the ground. For job to be done, he needed to exert a force on A. 3.995 cm C. 3.991 cm
the rope equivalent to 40 lbf through a distance of 38 ft. B. 3.985 cm D. 3.9955 cm
Calculate the work the mechanic must do. 76. An engine delivers 120 hp at 600 rpm. What is the angle of twist
A. 1440 N-m C. 480 ft-lb in the 6-ft drive shaft if its diameter is 2.5 inches and modulus of
B. 1952.8 N-m D. 1920 ft-lb rigidity is 12,000 ksi.
63. A ball with speed of 20 cm/s rolls off the edge of the table 90 cm A. 2.04 deg C. 3.09 deg
high. How far horizontally from the table edge does the ball B. 1.12 deg D. 4.05 deg
strike the ground? 77. What is the angular frequency of the block having a mass of 3 kg
A. 9.54m C. 7.32 m that is hang from a spring with spring modulus equal to 700 N/m?
B. 8.56 m D. 5.48 m A. 12.5 rad/s C. 11.2 rad/s
64. A mechanic uses a pulley system to raise a 120-lbf load that is 12 B. 15.3 rad/s D. 10.3 rad/s
ft from the ground. For job to be done, he exerted a force on the
 MACHINE DESIGN AND SHOP PRACTICE REFRESHER SET NO. 4
78. A block of mass 1.5 kg hangs from a spring of modulus 600 N/m. B. 120.5 D. 147.5
The block is pulled 12 cm below equilibrium and released. What 91. Mechanisms that are derived from the same kinematic chain but
is the period of the motion? have a different link fixed to ground.
A. 0.423 s C. 0.114 rad/s A. Linkage
B. 0.314 s D. 0.415 rad/s B. Mechanism
79. A certain vibrator obeys the following equation y =1.20 sin (1.10t C. Kinematic Chain
- 0.25) cm, for t is in seconds, and the angle is in radian. Calculate D. Kinematic Inversions
its velocity at t = 0 92. A steel bandsaw blade is 0.60 mm thick. If the modulus of
A. 2.34 cm/s C. 1.27 cm/s elasticity of steel is given to be 209 Gpa, calculate the bending
B. 1.39 cm/s D. 3.24 cm/s stress of the blade that is passing around the pulley of 420 mm
80. Calculate the tooth thickness on the pitch circle of 14 1/2 deg full diameter.
depth tooth of 16 diametral pitch. A. 298.6 Mpa C. 259.6 Mpa
A. 0.0982 in. C. 0.0897 in B. 329.8 Mpa D. 423.6 Mpa
B. 0.1209 in D. 0.0789 in 93. A multiple-disc clutch consists of 8 steel disc and 6 bronze discs.
81. What is the length in meters of a pendulum given that the period The effective diameters are 6 in and 4 in respectively. Compute
is 3.6 s? its power capacity if an axial force of 100 lb is applied to the shaft
A. 3.22 m C. 1.66 m rotating at 1000 rpm given the coefficient of friction of 0.32 using
B. 2.43 m D. 0.45 m uniform wear theory.
82. What is the value of the bending stress for a beam 40 mm wide A. 20.5 hp C. 43.2 hp
and 50 mm deep that is subjected to 3.7 kN-m bending moment B. 16.5 hp D. 13.4 hp
at each end? 94. A ventilating fan having an 18-in. cast iron pulley is driven from
A. 222 Mpa C. 332 Mpa a 25-hp at 870 rpm normal-torque motor placed directly below
B. 322 Mpa D. 252 Mpa it. The steel pulley on the motor is 10 in. in diameter, and the
83. A certain vibrator obeys the following equation y = 1.20 sin (1.10t center distance is 5 ft. What is the total length of the belt?
- 0 .25) cm, for t is in seconds, and the angle is in radian. Calculate A. 176.5 in C. 109.7 in
its acceleration at t = 0. B. 164.25 in D. 280.2 in
A. 0.16 cm/s2 C. 0.55 cm/s2 95. A plate clutch has single friction surface with outside diameter of
B. 0.36 cm/s 2 D. 0.26 cm/s2 12 inches and inside diameter of 6 inches. Calculate the torque
84. A ventilating fan having an 18-in. cast iron pulley is driven from that the clutch can carry given that the axial force is equal to
a 25-hp at 870 rpm normal-torque motor placed directly below 4000 lbf and a coef. of friction of 0.20. Note: use uniform
it. The steel pulley on the motor is 10 in. in diameter, and the pressure theory rind f= 0.2.
center distance is 5 ft. Calculate the belt speed. A. 4350 in-lbf C. 4508 in-lbf
A. 2280 fpm C. 1320 fpm B. 3733 in-lbf D. 2039 in-lbf
B. 2050 fpm D. 1540 fpm 96. A railroad track with rails 33 feet long is laid at a temperature of
85. A brass condenser tube 1 in. in diameter and 4 ft long has a wall 15°F with gaps of 0.01 feet between the ends of the rails. What
thickness equivalent to No. 16 BWG (wall thickness= 0.065 in). stress will result from a temperature at 110°F with a condition
Calculate the collapsing pressure. that they are prevented from buckling?
A. 3591 psi C. 1250 psi A. 9434 psi C. 9097 psi
B. 2450 psi D. 4250 psi B. 9787 psi D. 9654 psi
86. Two gear wheels are meshed together. The larger wheel has a 97. What is the maximum normal stress on an element of hollow
diameter of 0.75 cm and the smaller is 0.25 cm. how many sphere of radius 10” and thickness 0.1” that is subjected to an
revolutions does the smaller wheel turn when the larger turns 4 internal pressure of 100 psig?
revolutions. A. 5 000 psi C. 10 000 psi
A. 10 C. 12 B. 7 070 psi D. 14 140 psi
B. 14 D. 16 98. What is the cutting speed in fpm for a spindle speed of a lathe
87. A 12-in diameter pulley is belt driven with a net torque of 120 ft- that is turning an 8 in. diameter bronze using a spindle speed of
lb. Calculate the minimum tension in the belt if the ratio of 120 rpm?
tensions in the tight to slack sides of the belt is 3 is to 1? A. 220 fpm C. 2510 fpm
A. 360 lbf C. 240 in-lbf B. 301 fpm D. 251 fpm
B. 120 lbf D. 320 in-lbf 99. A helical-coil spring has a mean coil diameter of 1 inch and a wire
88. A brass condenser tube 1 in. in diameter and 4 ft long has a wall diameter of 1/8 inch. Determine the Wahl factor of the spring.
thickness equivalent to No. 16 BWG (wall thickness = 0.065 in). A. 1.148 C. 1.184
Determine the permissible working pressure with an apparent B. 1.41 D. 1.814
factor of safety of 10. 100. A 912 mm driving pulley and a 1220 mm driven pulley are being
A. 359.1 psi C. 253.2 psi set-up on a 3 meter center distance. The output of the driven
B. 254.7 psi D. 425.3 psi shaft is 72 hp. Compute the rpm of the driven shaft considering
89. A multiple-disk clutch has 22 pairs of identical mating friction that the belt speed is 1280 m/min with a coefficient of friction of
surfaces each with 10.25 in. outside diameter and 3.125 in. inside 0.30 and a slip of 1.5% each pulley.
diameter annular contact area. The disks are cast iron and steel A. 329 rpm C. 452.9 rpm
operating in an oil bath with a maximum pressure of 1,200 psi. B. 454 rpm D. 543.5 rpm
After this clutch has been in operation for a period of time and
has become worn, determine the probable power rating of this
clutch at 1,800 rpm. Note: f=0.06 for cast iron against steel (wet).
A. 2590 hp C. 1590 hp
B. 5290 hp D. 5350 hp
90. If rod’s diameter is 1.5 inches and its length is 65 inches, calculate
the slenderness ratio considering both ends are hinged.
A. 173.5 C. 150.7