LED-TV

Chassis : UNV81
Model : UA32T4202A*

SERVICE Manual

LED TV Contents

1. Precautions

2. Product specifications.

3. Disassembly and Reassembly

4. Trouble Shooting
4.1. Trouble Shooting
4-2. Factory Mode Adjustments
4-3. White Balance - Calibration
4-4. Software Upgrade

5. Exploded View & Part List

5-1.Rear Cover Dimension

6. Wiring Diagram
6-1. Wiring Diagram
6-2. Connector
6-3. Cables

7. Design
7.1 Front Rear View & Connections
7.2 Front Controls
7.3 Remote control
7.4 Viewing Front
T4202

Refer to the service manual in the GSPN (see the rear cover) for the more information.
1. Precautions
1-1. Safety Precautions
Follow these safety, servicing and ESD precautions to prevent damage and to protect against potential hazards such as
electrical shock.
1-1-1. Warnings
1. For continued safety, do not attempt to modify the circuit board.
2. Disconnect the AC power and DC power jack before servicing.
1-1-2. Servicing the LED TV
1. When servicing the LED TV, Disconnect the AC line cord from the AC outlet.
2. It is essential that service technicians have an accurate voltage meter available at all times.
Check the calibration of this meter periodically.
1-1-3. Fire and Shock Hazard
Before returning the LED TV to the user, perform the following safety checks:
1. Inspect each lead dress to make certain that the leads are not pinched or that hardware is not lodged between the
chassis and other metal parts in the LED TV.
2. Inspect all protective devices such as nonmetallic control knobs, insulating materials, cabinet backs, adjustment and
compartment covers or shields, isolation resistorcapacitor networks, mechanical insulators, etc.
3. Leakage Current Hot Check (Figure 1-1):
WARNING : Do not use an isolation transformer during this test.
Use a leakage current tester or a metering system that complies with American National Standards Institute (ANSI
C101.1, Leakage Current for Appliances), and Underwriters Laboratories (UL Publication UL1410, 59.7).

4. With the unit completely reassembled, plug the AC line cord directly into a 120V AC outlet. With the unit’s AC switch
first in the ON position and then OFF, measure the current between a known earth ground (metal water pipe, conduit,
etc.) and all exposed metal parts, including: metal cabinets, screwheads and control shafts.
The current measured should not exceed 0.5 milliamp.
Reverse the power-plug prongs in the AC outlet and repeat the test.
1-1-4. Product Safety Notices
Some electrical and mechanical parts have special safetyrelated characteristics which are often not evident from visual
inspection. The protection they give may not be obtained by replacing them with components rated for higher voltage,
wattage, etc. Parts that have special safety characteristics are identified by on schematics and parts lists. A substitute
replacement that does not have the same safety characteristics as the recommended replacement part might create
shock, fire and/or other hazards. Product safety is under review continuously and new instructions are issued whenever
appropriate.

1-2. Servicing Precautions

WARNING: An electrolytic capacitor installed with the wrong polarity might explode.
Caution: Before servicing units covered by this service manual, read and follow the Safety Precautions section of
this manual.
Note: If unforeseen circumstances create conflict between the following servicing precautions and any of the
safety precautions, always follow the safety precautions.
1-2-1 General Servicing Precautions
1. Always unplug the unit’s AC power cord from the AC power source and disconnect the DC Power Jack before
attempting to:
(a) remove or reinstall any component or assembly, (b) disconnect PCB plugs or connectors, (c) connect a test
component in parallel with an electrolytic capacitor.
2. Some components are raised above the printed circuit board for safety. An insulation tube or tape is sometimes
used. The internal wiring is sometimes clamped to prevent contact with thermally hot components. Reinstall all such
elements to their original position.
3. After servicing, always check that the screws, components and wiring have been correctly reinstalled. Make sure that
the area around the serviced part has not been damaged.
4. Check the insulation between the blades of the AC plug and accessible conductive parts (examples: metal panels,
input terminals and earphone jacks).
5. Insulation Checking Procedure: Disconnect the power cord from the AC source and turn the power switch ON.
Connect an insulation resistance meter (500 V) to theblades of the AC plug.
The insulation resistance between each blade of the AC plug and accessible conductive parts (see above) should be
greater than 1 megohm.
6. Always connect a test instrument’s ground lead to the instrument chassis ground before connecting the positive lead;
always remove the instrument’s ground lead last.
1-3. Electrostatically Sensitive Devices (ESD) Precautions
Some semiconductor (solid state) devices can be easily damaged by static electricity. Such components are commonly
called Electrostatically Sensitive Devices (ESD). Examples of typical ESD are integrated circuits and some field-effect
transistors. The following techniques will reduce the incidence of component damage caused by static electricity.
1. Immediately before handling any semiconductor components or assemblies, drain the electrostatic charge from your
body by touching a known earth ground. Alternatively, wear a discharging wrist-strap device. To avoid a shock hazard,
be sure to remove the wrist strap before applying power to the LED TV.
2. After removing an ESD-equipped assembly, place it on a conductive surface such as aluminum foil to prevent
accumulation of an electrostatic charge.
3. Do not use freon-propelled chemicals. These can generate electrical charges sufficient to damage ESDs.
4. Use only a grounded-tip soldering iron to solder or desolder ESDs.
5. Use only an anti-static solder removal device. Some solder removal devices not classified as “anti-static” can generate
electrical charges sufficient to damage ESDs.
6. Do not remove a replacement ESD from its protective package until you are ready to install it. Most replacement ESDs
are packaged with leads that are electrically shorted together by conductive foam, aluminum foil or other conductive
materials.
7. Immediately before removing the protective material from the leads of a replacement ESD, touch the protective
material to the chassis or circuit assembly into which the device will be installed.
Caution: Be sure no power is applied to the chassis or circuit and observe all other safety precautions.
8. Minimize body motions when handling unpackaged replacement ESDs. Motions such as brushing clothes together,
or lifting your foot from a carpeted floor can generate enough static electricity to damage an ESD.

1-4. Installation Precautions

1. For safety reasons, more than a people are required for carrying the product.
2. Keep the power cord away from any heat emitting devices, as a melted covering may cause fire or electric shock.
3. Do not place the product in areas with poor ventilation such as a bookshelf or closet. The increased internal
temperature may cause fire.
4. Bend the external antenna cable when connecting it to the product. This is a measure to protect it from being exposed
to moisture. Otherwise, it may cause a fire or electric shock.
5. Make sure to turn the power off and unplug the power cord from the outlet before repositioning the product. Also check
the antenna cable or the external connectors if they are fully unplugged. Damage to the cord may cause fire or electric
shock.
6. Keep the antenna far away from any high-voltage cables and install it firmly. Contact with the highvoltage cable or the
antenna falling over may cause fire or electric shock.
7. When installing the product, leave enough space (0.4m) between the product and the wall for ventilation purposes.
A rise in temperature within the product may cause fire.
2. Product specifications
Inch 32 inch(Real Inch 32)
Product Size(S-excluded) 732.9 x 440.3 x 78.5 mm
(S-included) 967.4 x 462.8 x 163.7 mm
(Box Package) 806.0 × 141.0 × 531.0mm
Stand Size 683.8 x 165.3mm
Viewing Angle 178/178
Power Consumption 48W
Weight (S-excluded) 4.2 kg
(S-included) 4.3 kg
(Box Package) 5.8 kg
Voltage (V) AC110-120V
Wall Mounted Yes
Stand Weight: 0.1 kg
USB, HDD Capacity Yes
IR OUT N/A
External Input HDMI/COMP/AV/ANT IN/USB
S-Video N/A
HDMI 1.4 Yes
USB
Yes
(Media Play)
3. Disassembly and Reassembly
This section of the service manual describes the disassembly and reassembly procedures
for the UN32T4202 LED TV.
WARNING: This LED TV contains electrostatically sensitive devices. Use caution when handling these components.

3-1. Disassembly and Reassembly

Cautions: 1. Disconnect the LED TV from the power source before disassembly.
2. Follow these directions carefully; never use metal instruments to pry apart the cabinet.
Description Picture Description
1. Place TV face down on cushioned
table.

2. Remove the 14screws on the back

cover.

3.
(1)Dismantling the Rear Cover .
(2)Take off the speaker wire.
(3)Take off the keypad wire.
(4)Take off the WIFI wire.

4.
(1)Pull down wire harness on the main
PCB
(2)Take off thd fix main PCB screw,
Remove the main PCB
(2)Take off thd fix T-con PCB screw,
Remove the T-con PCB
5. Take off the buckle line.
4. Trouble Shooting

4-1. Trouble Shooting

Main Ass'y

LVDS cable
WiFi cable

EMI solution

EMI solution

Function Ass'y

EMI solution

EMI solution WiFi

Speaker Speake
Block Diagram
PBA Board Picture
4-2. Factory Mode Adjustments
4-2-1 Entering Factory Mode
To enter ‘Service Mode’ Press the remote-control keys in this sequence :
● If you do not have Factory remote- control
Power Off Mute 8 2 Power On
●If you have Factory remote-control
INFO Factory
* If you don’t have Factory remote control, can’t control some menu.
Option
Control
Debug
SVC
ADC/WB
Advanced

4-2-2 Entering Factory Mode (SAMPLE)

※ If you replace the main board with new one, please change the factory option as well.
The options you must change are “Type”.
Model Name UN32T4202AGXPE UN32T4202AGXPR UN32T4202APXPA UN32T4202AGXZS
Vendor SDC
Panel
Code LSF320AN09-N
Vendor Solu-M Solu-M Solu-M Solu-M
SMPS
Code VT32HS048L0/RK VT32HS048L2/RK VT32HS048L3/RK VT32HS048L1/RK
1 Type 32A6AH0DT 32A6AH0DT 32A6AH0DT 32A6AH0DT

2 Local Set PERU_DTV PRA_DTV SELA CHILE_DTV

3 SW Model UT4300J UT4300J UT4300J UT4300J

4 BOM Model NA NA NA NA
5 Front Color UT5300MJ-U32NJ1 UT5300MJ-U32NJ1 UT5300MJ-U32NJ1 UT5300MJ-U32NJ1
6 Model Code UN32T4202AGXPE UN32T4202AGXPR UN32T4202APXPA UN32T4202AGXZS
(depending on the (depending on the
7 Tuner (depending on the country) (depending on the country)
country) country)
8 Ch Table NONE NONE NONE NONE

Factory Menu Name DATA DATA DATA DATA

Option
Factory Reset - - - -
Type 32A6AH0DT 32A6AH0DT 32A6AH0DT 32A6AH0DT
Local Set PERU_DTV PRA_DTV SELA CHILE_DTV
SW Model UT4300J UT4300J UT4300J UT4300J
BOM Model NA NA NA NA
Front Color UT5300MJ-U32NJ1 UT5300MJ-U32NJ1 UT5300MJ-U32NJ1 UT5300MJ-U32NJ1
Model Code UN32T4202AGXPE UN32T4202AGXPR UN32T4202APXPA UN32T4202AGXZS
TUNER (Auto detact, Depending on the country) (Auto detact, Depending on the country)(Auto detact, Depending on the country)(Auto detact, Depending on the country)
Ch Table NONE NONE NONE NONE
 Model Name UN32T4202AGXPE UN32T4202AGXPR UN32T4202APXPA UN32T4202AGXZS
Vendor HKC
Panel
Code PT320AT03-3
Vendor Solu-M Solu-M Solu-M Solu-M
SMPS
Code VT32HS048L4/RK VT32HS048L6/RK VT32HS048L7/RK VT32HS048L5/RK
1 Type 32K6AH0JN 32K6AH0JN 32K6AH0JN 32K6AH0JN

2 Local Set PERU_DTV PRA_DTV SELA CHILE_DTV

3 SW Model UT4300J UT4300J UT4300J UT4300J

4 BOM Model NA NA NA NA
5 Front Color UT5300MJ-U32NJ1 UT5300MJ-U32NJ1 UT5300MJ-U32NJ1 UT5300MJ-U32NJ1
6 Model Code UN32T4202AGXPE UN32T4202AGXPR UN32T4202APXPA UN32T4202AGXZS
(depending on the
7 Tuner (depending on the country) (depending on the country) (depending on the country)
country)
8 Ch Table NONE NONE NONE NONE

Factory Menu Name DATA DATA DATA DATA

Option
Factory Reset - - - -
Type 32K6AH0JN 32K6AH0JN 32K6AH0JN 32K6AH0JN
Local Set PERU_DTV PRA_DTV SELA CHILE_DTV
SW Model UT4300J UT4300J UT4300J UT4300J
BOM Model NA NA NA NA
Front Color UT5300MJ-U32NJ1 UT5300MJ-U32NJ1 UT5300MJ-U32NJ1 UT5300MJ-U32NJ1
Model Code UN32T4202AGXPE UN32T4202AGXPR UN32T4202APXPA UN32T4202AGXZS
TUNER (Auto detact, Depending on the country) (Auto detact, Depending on the country) (Auto detact, Depending on the country)
(Auto detact, Depending on the country)
Ch Table NONE NONE NONE NONE

Model Name UN32T4202AGXPE UN32T4202AGXPR UN32T4202APXPA UN32T4202AGXZS

Vendor CSOT
Panel
Code ST3151A07-2
Vendor Solu-M Solu-M Solu-M Solu-M
SMPS
Code VT32HS048L8PRK VT32HS048LAPR VT32HS048LBPRK VT32HS048L9PRK
1 Type 32S6AH0DB 32S6AH0DB 32S6AH0DB 32S6AH0DB

2 Local Set PERU_DTV PAR_DTV SELA CHILE_DTV

3 SW Model UT4300JV UT4300JV UT4300JV UT4300JV

4 BOM Model NA NA NA NA
5 Front Color UT5300MJ-U32NJ1 UT5300MJ-U32NJ1 UT5300MJ-U32NJ1 UT5300MJ-U32NJ1
6 Model Code UN32T4202AGXPE UN32T4202AGXPR UN32T4202APXPA UN32T4202AGXZS
(depending on the
7 Tuner (depending on the country) (depending on the country) (depending on the country)
country)
8 Ch Table NONE NONE NONE NONE

Factory Menu Name DATA DATA DATA DATA

Option
Factory Reset - - - -
Type 32S6AH0DB 32S6AH0DB 32S6AH0DB 32S6AH0DB
Local Set PERU_DTV PAR_DTV SELA CHILE_DTV
SW Model UT4300JV UT4300JV UT4300JV UT4300JV
BOM Model NA NA NA NA
Front Color UT5300MJ-U32NJ1 UT5300MJ-U32NJ1 UT5300MJ-U32NJ1 UT5300MJ-U32NJ1
Model Code UN32T4202AGXPE UN32T4202AGXPR UN32T4202APXPA UN32T4202AGXZS
TUNER (Auto detact, Depending on the country) (Auto detact, Depending on the country) (Auto detact, Depending on the country)
(Auto detact, Depending on the country)
Ch Table NONE NONE NONE NONE
4-3. White Balance - Calibration
4-3-1 White Balance -Calibration
Factory

ADC / WB AV Calibration
Comp Calibration
HDMI Calibration

4-3-2 Service Adjustment

- You must perform Calibration in the Lattice Pattern before adjusting the White Balance.C10
■ Color Calibration
Adjust spec.
1. Source : HDMI
2. Setting Mode : 1280*720@60Hz
3. Pattern : Pattern #24 (Only Chess Pattern)

4. Use Equipment : CA210 & Master MSPG925 Generator

Use other equipment only after comparing The result with that of The Master equipment.
Input mode Calibration Pattern
CVBS IN (Model_#1) Perform in NTSC B&W Pattern #24 Lattice
Component IN (Model_#6) Perform in 720p B&W Pattern #24 Lattice
HDMI IN Perform in 720p B&W Pattern #24 Lattice

■ Method of Color Calibration (AV)

1) Apply the NTSC Lattice (N0. 3) pattern signal to the AV IN 1 port
2) Press the Source key to switch to “AV1” mode
3) Enter Service mode
4) Select the “ADC” menu
5) Select the “AV Calibration” menu.
6) In “AV Calibration Off” status, press the “ ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “AV Calibration” status from Failure to Success.
■ Method of Color Calibration (Component)
1) Apply the 720p Lattice (N0. 6) pattern signal to the Component IN 1 port
2) Press the Source key to switch to “Component1” mode
3) Enter Service mode
4) Select the “ADC” menu
5) Select the “Comp Calibration” menu.
6) In “Comp Calibration Off” status, press the “ ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “Comp Calibration” status from Failure to Success.

■ Method of Color Calibration (HDMI)

1) Apply the 720p Lattice (N0. 6) pattern signal to the HDMI1/DVI IN port
2) Press the Source key to switch to “HDMI1” mode
3) Enter Service mode
4) Select the “ADC” menu
 5) Select the “HDMI Calibration” menu.
6) In “HDMI Calibration Off” status, press the “ ” key to perform Calibration.
7) When Calibration is complete, it returns to the high-level menu.
8) You can see the change of the “HDMI Calibration” status from Failure to Success.

4-3-3 White Balance - Adjustment

Factory (Low light) (High light)

Sub Bright Sub Contrast

ADC / WB - White Balance
R offset R gain
G offset G gain
B offset B gain

4-4. Software Upgrade

Samsung may offer upgrades for the TV’s firmware in the future.
These upgrades can be performed via the TV
when it is connected to the Internet, or by downloading the new
firmware from samsung.com to a USB memory device.
● Alternative Software (Backup) shows The previous version
that will be replaced.
● Software is represented as ‘Year/Month/Day_Version’.
The more recent the date, the newer the software version
Installing the latest version is recommended.

4-4-1. By USB
Insert a USB drive containing the firmware upgrade downloaded
from samsung.com into the TV.
Firmware folder must be on thre root directory of the USB.
Please be careful to not disconnect the power or remove
the USB drive while upgrades are being applied.

"MENU-->Support--> Software Update"

The TV will turn off and turn on automatically

after completing the firmware upgrade. Please check the firmware
version after the upgrades are complete (the new version will
have a higher number than the older version).
When software is upgraded, video and audio settings you have
made will return to their default (factory) settings. We recommend
you write down your settings so that you can easily reset them
after the upgrade.

4-4-2. By Online
Upgrades the software using the Internet.
● First, configure your network. For detailed procedures on using the Network Setting,
refer to the ‘Setting the Network’ instructions.
● If The internet connection doesn’t operate properly, connection can be broken, please retry downloading.
If the problem still happens, download by USB and upgrade.
4-4-3. Alternative Software (Backup)
If there is an issue with the new firmware and it is affecting operation, you can change the software to the previous
version.
● If Software was changed, existing Software is displayed.
● you can change current Software to Alternative Software by ‘Alternative Software’.
4-4-4 How to Check the Software Version
Use The Main Menu
1. press the "MENU" key in remote controller.
2. Select "Support" menu.
3. Locate the menu cursor "Software Upgrade" menu
4. Click the "INFO" Key.
Check the Main SW and Micom version

Use Factory Mode

4-4-5 How to Upgrade Software and Micom
Insert a USB drive containing the firmware upgrade downloaded from samsung.com into the TV.
Please be careful not to disconnect the power or remove the USB drive while upgrades are being applied.
The TV will turn off and turn on automatically after completing the firmware upgrade.
Please check the firmware version after the upgrades are complete (the new version will have a higher number than the older version).
When software is upgrade, video and audio settings you have made will return to their default(factory)settings.
We recommand you write down your settings before beginning firmware update. After is completed, restore your previous settings.
Main Software Upgrade
1. Store the sw program named "T-KTS2UABC" in USB memory stick.
Connect the USB

2. Click the "MENU" key in Remote Controler.

3. Select "Support" menu.
Locate the menu sursor "Software Update" menu.

4. Locate the menu sursor "Software now" menu.

5. Click the "ENTER" key.
6. Click the "ENTER" key.
Wait for upgrade complete.
Check the Software Version.
5. Exploded View & Part List
5-1.Rear Cover Dimension

wall mount pitch 100*100(mm)

6. Wiring Diagram

6-1. Wiring Diagram

■ UN32T4202

CN1402_HD

MAIN ASSY CN1202

CN1201

CN402
LED
CNL802 ASSY

SDC O/C

Function WiFi
ASSY Speaker Speaker ASSY
6-2. Connector
6-2-1. For All Inch

6. CNL802(to LED)
1 LED+ 3 LED-
2 NC

7. CN402 (to Speaker)

1 R+ 3 L+
2 R- 4 L-

8. CN1201( to Function/IR )
1 IR 5 MSDA_I2C
2 GND 6 KEY_INPUT1
3 A3.3V 7 KEY_INPUT2
4 MSCL_I2C 8 LED_STB_OUT

9. CN1202(to WIFI)
1 WIFI_NRESET 6 WIFI_+_USB_WIFI
2 WIFI_WOL 7 GND
3 A5V_PW 8 WIFI_PHY_ON
4 GND 9 NC
5 WIFI_-_USB_WIFI 10 BT_WAKE

10. CN1402_HD(to OC)

1 PANEL_VCC 16 EVEN_CLK+
2 PANEL_VCC 17 EVEN_CLK-
3 PANEL_VCC 18 GND
4 PANEL_VCC 19 EVEN2+
5 PANEL_VCC 20 EVEN2-
6 GND 21 GND
7 GND 22 EVEN1+
8 GND 23 EVEN1-
9 TCON_WP 24 GND
10 GND 25 EVEN0+
11 NC 26 EVEN0-
12 GND 27 GND
13 EVEN3+ 28 TCON_SDA
14 EVEN3- 29 TCON_SDL
15 GND 30 NC
6-3. Cables

use LVDS CALBE FUNCTION WIFI Wire

code 046028301631 098009000501 046030100660

photo
7. Design
7.1 Front Rear View & Connections

Rear Inlay
7.2 Front Controls
7.3 Remote control
7.4 Viewing Front