DUNGS GW 150 A6 (Pressure Switch Aux Boiler)
DUNGS GW 150 A6 (Pressure Switch Aux Boiler)
DUNGS GW 150 A6 (Pressure Switch Aux Boiler)
switches
for gas and air
GW…A6
GW…A6/1
5.01
Application
Pressure monitoring in combustion,
ventilation and air-conditioning tech-
nologies.
Suitable for gases of families 1,2,3 and
other neutral gaseous media.
1…6
Functional description GW…A6 pressure switch
Switching function
Single-acting pressure switch in over- The control unit responds to pressure. If
pressure range. the setpoint is exceeded or undershot,
If pressure increases:
The pressure switches operate without the circuit is switched on, off or over.
1 NC opens, 2 NO closes.
any power supply.
If pressure drops:
GW… / …A6 double pressure
1 NC closes, 2 NO opens.
Switching response switch
GW…A6 Combination of two flanged GW...
Short response time during pressure A6 single pressure switches. The two
fluctuations. setpoints are set separately and inde-
pendently. A combination of different 2 NO
GW…A6/1 setpoint ranges is therefore possible. COM
Slow response time during short-term The two control units are fed from the
pressure fluctuations by additional same medium at the medium’s pres- 3
damping nozzle. sure. 1 NC
p
2 NO
COM
Definition of ∆p switching differ-
ence 3 1 NC
The ∆p switching difference is the Pressure at
control unit
pressure difference between the up-
p
Setting tolerance
per and lower switching pressure. upper switching N
Adjustment when
∆p switching difference
pressure (ON)
pressure drops
2 NO
COM
falling
3 1 NC
lower switching
rising
pressure (OFF)
p N
3,5 27,5
25
3 22,5
20
2,5
17,5
2
[ mbar]
15
[ mbar ]
12,5
1,5
10
1 7,5
5
0,5 2,5
0
0
p↓ [mbar]
p ↓ [mbar]
2…6
Specifications
Pressure connection Standard (V0): centrally on housing bottom, G 1/4 inner thread
as per ISO 228
Special design (V3): additionally G 1/4 inner thread (side right)
Electrical connection Terminal connection for line sockets as per DIN EN 175 301-803, 3-pin,
protection-insulated without ground connection
Setting tolerance ± 15% switch point deviation referred to setpoint, adjusted for dropping pres-
sure, vertical diaphragm position
Deviation Permissible deviation of the set value ≤ ± 15 % in the service life test according
to EN 1854
1 no
2 no Pressure tap 3
Pressure tap 4
Pressure tap 1
3 pe (p1)
Pressure tap 2
4 pa (p2)
3…6
Dimensions [mm]
Pressure connection, optional
with damping nozzle in GW…A6/1
GW … A6, A6/1
Optional
ø 5,2
27,4
Pressure connection G 1/4
34
43
53,75
73
12,5
2
3
ø 4,2
1
58,4
39,2
10,3
18
Test nipple ø 9
Sealing screw
Oblong slot 1,0
72
42
Made in Germany
26
IP 54
Installation position
2
1
3
higher.
1
3
a pressure lower.
2 1
3
1
2
α
switch switches at pressure deviating from the set reference value.
4…6
Designation
Pressure connection
V0 Pressure connection G 1/4
position 0
V3 Pressure connection G 1/4
position 3
Sealing screw
VS0 Sealing screw at position 0
VS3 Sealing screw at position 3
Test nipple
MS9 Test nipple at position 9
GW 150 A6 [Ag-G3-MS9-V0-VS3]
Accessories for GW A6
pressure switch
5…6
Compact pressure switches
for gas and air
GW…A6
GW…A6/1
We reserve the right to make any changes in the interest of technical progress.