Nice RF
Nice RF
www.nicerf.com SA828
Catalogue
1. Description ............................................................................................................................................................. - 3 -
2. Features .................................................................................................................................................................. - 3 -
3. Application ............................................................................................................................................................. - 3 -
4. Internal block diagram ........................................................................................................................................... - 3 -
5. Interface description ...............................................................................................................................................- 4 -
6. Specification ...........................................................................................................................................................- 4 -
7. Typical application schematic ................................................................................................................................- 5 -
8. Parameter configuration .........................................................................................................................................- 6 -
9. Communication protocol ....................................................................................................................................... - 7 -
10. Accessories ...........................................................................................................................................................- 9 -
11. Pin definition ...................................................................................................................................................... - 10 -
12. Mechanism Dimension(Unit:mm) ..................................................................................................................... - 11 -
13. Order information ...............................................................................................................................................- 11 -
14. FAQ .................................................................................................................................................................... - 12 -
Appendix 1:Display and Sending Table of CTCSS/CDCSS ................................................................................- 13 -
Appendix 2: Analog subtone comparison table .......................................................................................................- 16 -
Appendix 3:SMD Reflow Chart ........................................................................................................................... - 17 -
6. Specification
Parameter Test condition Min Typ. Max Unit
Power supply 3.3 4.2 5.5 V
Working Temperature range -30 25 70 ℃
Current Consumption
Sleep current ≤3 uA
RX current 60 mA
TX current(High power) 800 900 mA
TX current(low power) 350 450 mA
Transmitting RF Parameters
UHF 400 450 470 MHz
Frequency range VHF 134 150 174 MHz
350 320 350 400 MHz
Out power(high power) 30 31.5 32.5 dBm
@VCC=4.0V
Out power(low power) 25 26.5 28 dBm
@1.5KHz/2.5KHz
modulation sensitivity 10 mV
Frequency deviation
@1.5KHz/2.5KHz
Audio distortion 2 5 %
Frequency deviation
@1.5KHz/2.5KHz
Signal to noise ratio 38 40 45 dB
Frequency deviation
Adjacent-channel power @12.5K offset -60dBc dBm
CTCSS modulated frequency
0.35 0.5 0.75 KHz
deviation
RX frequency Parameter
RX sensitivity -124 dBm
@1.5KHz
RX SNR 45 50 dB
Frequency deviation
Audio output power 2 W
Audio output impedance 8 OHm
PC software can read the module’s parameter after connecting successfully, As shown below:
9. Communication protocol
Commands Format:
After module running, the standard setting of serial port as below::
Baud Rate:9600 bps Date Bit:8 Stop:1 Parity: None
Instruction return format:
Return true:OK\r\n,Return false:ERROR\r\n
Frame format Definition :
ASCII is used in communication protocol。
★ Note: CDCSS can be checked in Appendix1
Read parameter
Format:AA FA 1
Return:AA FA TFV1,RFV2,.....,TFV16,RFV16,TX_SUBAUDIO,RX_SUBAUDIO,
SQ
Format:AA FA 2
Return Value:“OK\r\n”OR "ERROR\r\n"
Example:AA FA 2 (Hex 41 41 46 41 32 )
Return:OK\r\n(Hex 4f 4b 0d 0a)
10. Accessories
1) Antenna
The antenna is very important for RF communication. Its performance will affect the communication .
The module requires the antenna with 50Ω impedance. Universal antennas are Rod antenna, sucker
antenna and telescopic antenna, User can choose the right antenna according to their application. We
advise to use antennas listed on our website to get better performance.
Subtone
1 2 3 4 5 6 7 8 9 10
coding
Sub-audio
67 71.9 74.4 77 79.7 82.5 85.4 88.5 91.5 94.8
frequency
Subtone
11 12 13 14 15 16 17 18 19 20
coding
Sub-audio
97.4 100 103.5 107.2 110.9 114.8 118.8 123 127.3 131.8
frequency
Subtone
21 22 23 24 25 26 27 28 29 30
coding
Sub-audio
136.5 141.3 146.2 151.4 156.7 162.2 167.9 173.8 179.9 186.2
frequency
Subtone
31 32 33 34 35 36 37 38
coding
Sub-audio
192.8 203.5 210.7 218.1 225.7 233.6 241.8 250.3
frequency
We recommend you should obey the IPC related standards in setting the reflow profile: