Service Manual: U1B/N1B/K1B /FN

Service M-CR611 /U1B/N1B/K1B
/FN
Manual NETWORK CD RECEIVER
• For purposes of improvement, specifications and design are subject to change without notice.
• Please use this service manual with referring to the operating instructions without fail.
• Some illustrations using in this service manual are slightly different from the actual set.
Ver. 4
M-CR611 Please refer to the
MODIFICATION NOTICE.
Copyright 2016 D&M Holdings Inc. All rights reserved.

S1315V04DM/DG1607 WARNING: Violators will be prosecuted to the maximum extent possible.
Contents
ABOUT THIS MANUAL.................................................................3 PROCEDURE AFTER REPLACING

What you can do with this manual............................................3 THE MICROPROCESSOR, ETC....................................................30
Using Adobe Reader (Windows version)....................................4 FIRMWARE UPDATE PROCEDURE.............................................31
SAFETY PRECAUTIONS................................................................6 1. Updating via USB................................................................31
NOTE FOR SCHEMATIC DIAGRAM...............................................7 2. Forced USB All Device Write Mode.....................................33
NOTE FOR PARTS LIST.................................................................7 3. Update Procedure in the Event of a CY920 Error................33
4. Updating via DPMS.............................................................34
TECHNICAL SPECIFICATIONS......................................................9
5. Error code table f..............................................................35
DIMENSION...............................................................................10
TROUBLE SHOOTING.................................................................36
CAUTION IN SERVICING............................................................11 1. OLED dose not light............................................................36
Initializing This Unit..................................................................11 2. No Sound. Noise generated................................................37
Service tools.............................................................................11
MEASURING METHOD AND WAVEFORMS................................45
Replacing the WLAN MODULE with a new one.......................11
1. TEST POINT..........................................................................45
Removing the AMP PCB from the MAIN PCB...........................12
2. WAVEFORMS.......................................................................46
DISASSEMBLY...........................................................................13
BLOCK DIAGRAM......................................................................48
1. TOP PANEL..........................................................................15
2. FRONT PANEL ASSY.............................................................15 POWER DIAGRAM.....................................................................49
3. CD MECHA ASSY.................................................................16 WIRING DIAGRAM.....................................................................50
4. MECHA SUPPORT L/R..........................................................16 PRINTED CIRCUIT BOARDS.......................................................51
5. TUNER.................................................................................16 SCHEMATIC DIAGRAMS (1/10)..................................................56
6. SHIELD COVER.....................................................................17 SCH01_MAIN_MCU_PWM.......................................................56
7. SMPS PCB............................................................................17 SCH02_MAIN_NETWORK.........................................................57
8. BACK CHASSIS ASSY............................................................18 SCH03_MAIN_DAB...................................................................58
9. MAIN PCB ASSY...................................................................18 SCH04_CNT..............................................................................59
NOTES ON HANDLING AND SCH05_NFC..............................................................................60
REPLACEMENT OF THE LASER PICK-UP...................................19 SCH06_AMP_611.....................................................................61
1. Protection of the LD............................................................19 SCH07_FRONT_611..................................................................62
2. Precautions when handling the laser CD mechanism........19 SCH08_INPUT...........................................................................63
3. Cautions on assembling and adjustment...........................19 SCH09_CD................................................................................64
4. Determining whether the laser pick-up is defective...........19 SCH10_SMPS............................................................................65
SPECIAL MODE..........................................................................20 EXPLODED VIEW.......................................................................66
Special mode setting button...................................................20 PACKING VIEW..........................................................................67
1. Factory Initialization Mode.................................................21 SEMICONDUCTORS...................................................................68
2. User Initialization Mode......................................................22 1. IC's.......................................................................................68
3. Version Display Mode.........................................................23 2. DISPLAY..............................................................................91
4. CD test mode......................................................................25
5. Protection History Display Mode........................................28
2
ABOUT THIS MANUAL
Read the following information before using the service manual.
What you can do with this manual
Search for a Ref. No. (phrase) Jump to the target of a schematic

(Ctrl+Shift+F) diagram connector
You can use the search function in Acrobat Reader to

search for a Ref. No. in schematic diagrams, printed
Click the Ref. No. of the target connector in the red
wiring circuit diagrams, block diagrams, and parts
box around a schematic diagram connector.
lists.
•The screen jumps to the target connector.
1.Press Ctrl+Shift+F on the keyboard.

• The Search window appears.
CP401
v
F
Shift
Ctrl
2.Enter the Ref. No. you want to search for in the

Search window, and then click the Search button. CP106
•A list of search results appears.
•Page magnification stays the same as before the

jump.
3.Click an item on the list.

• The screen jumps to the page for that item, and the
search phrase is displayed.
3
Using Adobe Reader (Windows version)
Add notes to this data (Sign) Magnify schematic / printed circuit

The Sign function lets you add notes to the data in board diagrams - 1
this manual. (Ctrl+Space, mouse operation)
Save the file once you have finished adding notes.
Press Ctrl+Space on the keyboard and drag the
[Example using Adobe Reader X] mouse to select the area you want to view.
On the "View" menu, click "Sign".
• The selected area is magnified.
• The Sign pane appears.
Ctrl Space
• When you want to move the area shown, hold

down Space and drag the mouse.
[Example using Adobe Reader 9]

On the "Document" menu, click "Sign". • When you want to show a full page view, press
Ctrl+0 on the keyboard.
Print a magnified part of the manual

The Properties dialog box and functions will vary depending on your printer.
1. Drag the mouse to magnify the part you want to print.
2. On the "File" menu, click "Print".
3. Configure the following settings in the Print dialog box.
• Properties
Click this button and check that the printer is set to a
suitable paper size.
• Page to print
Select the following checkbox.
"More Options" : "Current View"
• Page Sizing & Handling
Select the following checkbox.
"Size" / "Size Options" : "Fit"
4. Click the Print button to start printing.
4
Magnify schematic / printed circuit Magnify schematic / printed circuit
board diagrams - 2 board diagrams - 3
(Pan & Zoom function) (Loupe Tool function)
The Pan & Zoom function lets you see which part of The Loupe Tool function lets you magnify a specific
a magnified diagram is being shown in a separate part of a diagram in a separate window.
window.
[Example using Adobe Reader X]
[Example using Adobe Reader X] On the "View" menu, point to "Zoom", and then click
On the "View" menu, point to "Zoom", and then click "Loupe Tool".
"Pan & Zoom".
• The Loupe Tool window appears on the screen.

• The Pan & Zoom window appears on the screen.
[Example using Adobe Reader 9] [Example using Adobe Reader 9]

On the "Tools" menu, point to "Select & Zoom", and On the "Tools" menu, point to "Select & Zoom", and
then click "Pan & Zoom Window". then click "Loupe Tool Window".
5
SAFETY PRECAUTIONS
The following items should be checked for continued protection of the customer and the service technician.
leakage current check
Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis
resistance check. If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the
power cord is less than 460 kohms, the set is defective.
Be sure to test for leakage current with the AC plug in both polarities, in addition, when the set's power is in each state
(on, off and standby mode), if applicable.
CAUTION Please heed the following cautions and instructions during servicing and
inspection.
◎◎ Heed the cautions! ◎◎ Make a safety check after servicing!
Cautions which are delicate in particular for servicing Check that all screws, parts and wires removed or
are labeled on the cabinets, the parts and the chassis, disconnected when servicing have been put back in their
etc. Be sure to heed these cautions and the cautions original positions, check that no serviced parts have
described in the handling instructions. deteriorate the area around. Then make an insulation
◎◎ Cautions concerning electric shock! check on the external metal connectors and between
(1) A n AC voltage is impressed on this set, so if you the blades of the power plug, and otherwise check that
touch internal metal parts when the set is energized, safety is ensured.
you may get an electric shock. Avoid getting an (Insulation check procedure)
electric shock, by using an isolating transformer Unplug the power cord from the power outlet, disconnect
and wearing gloves when servicing while the set is the antenna, plugs, etc., and on the power. Using a 500V
energized, or by unplugging the power cord when insulation resistance tester, check that the insulation
replacing parts, for example. resistance value between the inplug and the externally
(2) There are high voltage parts inside. Handle with exposed metal parts (antenna terminal, headphones
extra care when the set is energized. terminal, input terminal, etc.) is 1MΩ or greater. If it is
◎◎ C
aution concerning disassembly and less, the set must be inspected and repaired.
assembly!
Through great care is taken when parts were
manufactured from sheet metal, there may be burrs on
the edges of parts. The burrs could cause injury if fingers
are moved across them in some rare cases. Wear gloves CAUTION Concerning important
to protect your hands. safety parts
◎◎ Use only designated parts! Many of the electric and the structural parts used in the
The set's parts have specific safety properties (fire set have special safety properties. In most cases these
resistance, voltage resistance, etc.). Be sure to use parts properties are difficult to distinguish by sight, and the use
which have the same properties for replacement. The of replacement parts with higher ratings (rated power
burrs have the same properties. In particular, for the and withstand voltage) does not necessarily guarantee
important safety parts that are indicated by the z mark that safety performance will be preserved. Parts with
on schematic diagrams and parts lists, be sure to use safety properties are indicated as shown below on the
the designated parts. wiring diagrams and the parts list in this service manual.
◎◎ B
e sure to mount parts and arrange the wires Be sure to replace them with the parts which have the
as they were originally placed! designated part number.
For safety seasons, some parts use tapes, tubes or other
insulating materials, and some parts are mounted away (1) Schematic diagrams........Indicated by the z mark.
from the surface of printed circuit boards. Care is also (2) Parts lists........Indicated by the z mark.
taken with the positions of the wires by arranging them The use of parts other than the
and using clamps to keep them away from heating and designated parts could cause electric
high voltage parts, so be sure to set everything back as shocks, fires or other dangerous
it was originally placed. situations.
6
NOTE FOR SCHEMATIC DIAGRAM
WARNING:
Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
CAUTION:
Before returning the set to the customer, be sure to carry out either (1) a leakage current check or (2) a line to chassis resistance check.
If the leakage current exceeds 0.5 milliamps, or if the resistance from chassis to either side of the power cord is less than 460 kohms, the
set is defective.
WARNING:
DO NOT return the set to the customer unless the problem is identified and remedied.
NOTICE:
ALL RESISTANCE VALUES IN OHM. k=1,000 OHM / M=1,000,000 OHM
ALL CAPACITANCE VALUES ARE EXPRESSED IN MICRO FARAD, UNLESS OTHERWISE INDICATED. P INDICATES MICRO-MICRO
FARAD. EACH VOLTAGE AND CURRENT ARE MEASURED AT NO SIGNAL INPUT CONDITION. CIRCUIT AND PARTS ARE SUBJECT
TO CHANGE WITHOUT PRIOR NOTICE.
NOTE FOR PARTS LIST

1. Parts indicated by "nsp" on this table cannot be supplied.
2. When ordering a part, make a clear distinction between "1" and "I" (i) to avoid mis-supplying.
3. A part ordered without specifying its part number can not be supplied.
4. Part indicated by " ★ " mark is not illustrated in the exploded view.
WARNING: Parts indicated by the z mark have critical characteristics. Use ONLY replacement parts recommended by the manufacturer.
INSTRUCTIONS FOR HANDLING SEMI-CONDUCTORS AND OPTICAL UNIT

Electrostatic breakdown of the semi-conductors or optical pickup may occur due to a potential difference caused by
electrostatic charge during unpacking or repair work.
1. Ground for Human Body

Be sure to wear a grounding band (1 MΩ) that is properly grounded to remove any static electricity that may be
charged on the body.
2. Ground for Workbench

Be sure to place a conductive sheet or copper plate with proper grounding (1 MΩ) on the workbench or other surface,
where the semi-conductors are to be placed. Because the static electricity charge on clothing will not escape through
the body grounding band, be careful to avoid contacting semi-conductors with your clothing
<Incorrect> <Correct> Grounding Band
1MΩ
CBA
CBA
1MΩ
Conductive Sheet or
Copper Plate
7
GB WARNING NL WAARSCHUWING
All ICs and many other semi-conductors are

susceptible to electrostatic discharges (ESD). Alle IC’s en vele andere halfgeleiders zijn
Careless handling during repair can reduce gevoelig voor elektrostatische ontladingen
life drastically. (ESD).
When repairing, make sure that you are Onzorgvuldig behandelen tijdens reparatie
connected with the same potential as the kan de levensduur drastisch doen
mass of the set via a wrist wrap with verminderen.
resistance. Zorg ervoor dat u tijdens reparatie via een
Keep components and tools also at this polsband met weerstand verbonden bent met
potential. hetzelfde potentiaal als de massa van het
apparaat.
Houd componenten en hulpmiddelen ook op
ditzelfde potentiaal.
F ATTENTION D WARNUNG AVVERTIMENTO

I
Tous les IC et beaucoup d’autres semi- Alle IC und viele andere Halbleiter sind Tutti IC e parecchi semi-conduttori sono
conducteurs sont sensibles aux décharges empfindlich gegen elektrostatische sensibili alle scariche statiche (ESD).
statiques (ESD). Entladungen (ESD). La loro longevita potrebbe essere fortemente
Leur longévité pourrait être considérablement Unsorgfältige Behandlung bei der Reparatur ridatta in caso di non osservazione della piu
écourtée par le fait qu’aucune précaution kann die Lebensdauer drastisch vermindern. grande cauzione alla loro manipolazione.
n’est prise a leur manipulation. Sorgen sie dafür, das Sie im Reparaturfall Durante le riparazioni occorre quindi essere
Lors de réparations, s’assurer de bien être über ein Pulsarmband mit Widerstand mit collegato allo stesso potenziale che quello
relié au même potentiel que la masse de dem Massepotential des Gerätes verbunden della massa dell’apparecchio tramite un
l’appareil et enfiler le bracelet serti d’une sind. braccialetto a resistenza.
résistance de sécurité. Halten Sie Bauteile und Hilfsmittel ebenfalls Assicurarsi che i componenti e anche gli
Veiller a ce que les composants ainsi que les auf diesem Potential. utensili con quali si lavora siano anche a
outils que l’on utilise soient également a ce questo potenziale.
potentiel.
GB D
Safety regulations require that the set be restored to its original condition Bei jeder Reparatur sind die geltenden Sicherheitsvorschriften zu beachten.
and that parts which are identical with those specified be used. Der Originalzustand des Gerats darf nicht verandert werden.
Fur Reparaturen sind Original-Ersatzteile zu verwenden.
NL I
Veiligheidsbepalingen vereisen, dat het apparaat in zijn oorspronkelijke Le norme di sicurezza esigono che l’apparecchio venga rimesso nelle
toestand wordt terug gebracht en dat onderdelen, identiek aan de condizioni originali e che siano utilizzati pezzi di ricambiago idetici a quelli
gespecifieerde worden toegepast. specificati.
F
“Pour votre sécurité, ces documents
doivent être utilisés par des Les normes de sécurité exigent que l’appareil soit remis a l’état d’origine et
spécialistes agrées, seuls habilités à que soient utilisées les pièces de rechange identiques à celles spécifiées.
réparer votre appareil en panne.”
LASER SAFETY
This unit employs a laser. Only a qualified service person should remove the cover or attempt to service this
device, due to possible eye injury.
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE

SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
AVOID DIRECT EXPOSURE TO BEAM
WARNING
The use of optical instruments with this product will increase eye hazard.
Repair handling should take place as much as possible with a disc loaded inside the player
WARNING LOCATION: INSIDE ON LASER COVERSHIELD

CAUTION VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID EXPOSURE TO BEAM
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING VED ÅBNING UNDGÅ UDSÆTTELSE FOR STRÅLING
ADVARSEL SYNLIG OG USYNLIG LASERSTRÅLING NÅR DEKSEL Å PNES UNNGÅ EKSPONERING FOR STRÅLEN
VARNING SYNLIG OCH OSYNLIG LASERSTRÅLNING NÄR DENNA DEL ÄR ÖPPNAD BETRAKTA EJ STRÅLEN
VARO! AVATT AESSA OLET ALTTIINA NÄKYVÄLLE JA NÄKYMÄTTÖMÄLLE LASER SÄTEILYLLE. ÄLÄ KATSO SÄTEESEEN
VORSICHT SICHTBARE UND UNSICHTBARE LASERSTRAHLUNG WENN ABDECKUNG GEÖFFNET NICHT DEM STRAHL AUSSETSEN
DANGER VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN AVOID DIRECT EXPOSURE TO BEAM
ATTENTION RAYONNEMENT LASER VISIBLE ET INVISIBLE EN CAS D'OUVERTURE EXPOSITION DANGEREUSE AU FAISCEAU
030804ecm
8
TECHNICAL SPECIFICATIONS
nn Audio section nn Wireless LAN section
• CD player Network type Conforming to IEEE 802.11b
Playable frequency response： 10 ～ 20 kHz (wireless LAN standard)： Conforming to IEEE 802.11g
Conforming to IEEE 802.11n
Wow & flutter： Below measurable limits (± 0.001% ) (Wi-Fi® compliant)*1
Sampling frequency： 44.1 kHz Security： WEP 64bit, WEP 128bit
• Audio amplifier WPA/WPA2-PSK(AES)
Rated output： 2-channel driving WPA/WPA2-PSK(TKIP)
50 W + 50 W Radio frequency： 2.4 GHz
(6 Ω, 1 kHz, THD+N 0.7 %) No. of channels： for N, K, F：1-13ch
Dynamic power： 60 W + 60 W for U：1-11ch
(6 Ω, 1 kHz, THD+N 10 %) *1 The Wi-Fi® CERTIFIED Logo and the Wi-Fi CERTIFIED On-Product Logo
Output terminals： Speaker：4 – 16 Ω (impedance) are registered trademarks of the Wi-Fi Alliance.
Compatible with headphones/stereo nn Bluetooth section
headphones
Communications system： Bluetooth Version 2.1 + EDR (Enhanced
Input sensitivity/Input impedance：Analog In：200 mV / 22 kΩ Data Rate)
Total harmonic distortion（1 kHz、5 W、6 Ω）：Analog In：0.1 % Transmission power： Maximum 2.5 mW (Class 2)
S/N ratio（10 W、6 Ω、IHF-A）：Analog In：90 dB Maximum communication range： Approx. 32.8 ft/10 m in line of
Tone control： Dynamic Bass Boost： +8 dB (100 Hz) sight *2
Bass： ±10 dB (100 Hz) Frequency band： 2.4 GHz band
Treble： ±10 dB (10 kHz)
Supported profiles： FHSS (Frequency-Hopping Spread
Frequency response： Analog In： 5 Hz – 40 kHz (± 3dB) Spectrum)
nn Tuner section Supported profiles：A2DP (Advanced Audio Distribution Profile) 1.2
Receiving Range： for U FM 87.50 MHz – 107.90 MHz AVRCP (Audio Video Remote Control Profile) 1.4
for N, K FM 87.50 MHz – 108.00 MHz Corresponding codec： SBC, AAC
for F FM 76.00MHz – 95.00MHz Transmission range (A2DP)： 20 Hz - 20,000 Hz
for U AM 520 kHz – 1710 kHz
for N, K AM 522 kHz – 1611 kHz *2 The actual communication range varies depending on the influence of
for F AM 522 kHz – 1629 kHz such factors as obstructions between devices, electromagnetic waves
from microwave ovens, static electricity, cordless phones, reception
Effective sensitivity： FM 1.2 μV / 75 Ω sensitivity, antenna performance, operating system, application
AM 20 μV software etc.
FM Channel separation： 42 dB (1 kHz)
nn Clock / Alarm / Sleep
FM S/N ratio： Monaural：74 dB
Stereo：70 dB Clock type： Power line frequency synchronized method
(Within ±60 seconds per month)
THD+N（1kHz）
： Monaural：0.3 %
Stereo：0.4 % Alarm： Once alarm/Everyday alarm：One system each
nn DAB tuner section Sleep： Sleep timer：Max. 90 minutes
Receiving Range： 174.928 (5A) – 239.200 (13F) MHz (BAND III) nn General
Effective sensitivity： –85 dBm Power supply： for U AC120 V, 60 Hz
for N AC 220 - 230 V, 50/60 Hz
S/N ratio： 95 dB for K AC 220 V, 50 Hz
for F AC 100V, 50/60Hz
Power consumption： 55 W
Power consumption in standby mode： 0.3 W
Power consumption in“Network Control”–“On”mode： 3W
For purposes of improvement, specifications and design are subject to
change without notice.
9
DIMENSION
Unit：in. (mm)
Weight：7 lbs 4 oz (3.4 kg)
1 7/8
(46)
12 1/8 (305)
8 5/8 (218)
1/8 1 1/2
(3) (38)
4 3/4 (120)
5 1/8 (130)
11 1/2 (292)
4 1/4 (105)
1 1/4
1/4
(6)
(30)
1 1/2 1 1/2
(35) 8 3/8 (210) (35)
10
CAUTION IN SERVICING
Initializing This Unit
Make sure to initialize this unit after replacing the microcomputer or any peripheral equipment, or the digital PCB.
1. Press the power operation button "X" to turn off the power, and remove the power plug from the socket.
2. Insert the power plug into the socket while pressing and holding the "WPS" and "iOS" buttons on the rear panel.
(Factory Reset)
3. Press the power operation button "X" to turn off the power, and remove the power plug from the socket.
4. Insert the power plug while pressing the power operation button "X". (Starts in Special mode.)
5. Press the "CURSOR d" button, and press the "Enter" button on the "Initialize" display. (Initialized)
6. Wait for more than 90 seconds after "Initialized" is displayed and then turn the power off. s
(During this time, start and initialize the network devices.)
NOTE： Initializing the device restores the customized settings to the factory settings. Write down your settings
in advance and reconfigure the settings after initialization.
WPS iOS
Service tools
Measuring Disc : CD/TCD-784
CD-R/TCD-R082W
CD-RW/TCD-W082W
z See "MEASURING METHOD AND WAVEFORMS".
Replacing the WLAN MODULE with a new one

After replacing the WLAN MODULE (CY920-C) with a new one, make sure to follow the procedure below.
NOTE WLAN MODULE and NFC PCB are supplied as a set to ensure consistency of the BT ADDRESS.
Replace as a set even if only one of the parts is faulty.
(1) Replace the WLAN MODULE with the following modules for each destination.
MODULE Name Remarks
N/U/F/K
CY920 MODULE MCR611 / NFC PCB / ANT ASSY
See the Parts list for the Parts Number.
(2) Update the firmware via the USB Memory.
(See page 31)
11
Removing the AMP PCB from the MAIN PCB
Pay close attention to the following two points when removing/attaching the AMP PCB to the MAIN PCB during servicing.
1. W
ait for approximately 5 minutes after turning the power off before removing the wire connector that connects the
SMPS PCB and AMP PCB.
When connected to the SMPS PCB wire connector, a surge current may flow due to the charge stored in the AMP PCB
causing damage to the D-AMP IC500 and IC502.
2. W
hen attaching the AMP PCB to the MAIN PCB connector, insert the connector pins into the AMP PCB in advance, and
securely connect while checking that the position is correct.
If the MAIN PCB and AMP PCB terminals are connected incorrectly (if the connection pins are misaligned), the PWM
Processor IC108, D-AMP IC500 and IC502 may be damaged by the charge stored in the condenser.
12
DISASSEMBLY
• Remove each part following the flow below.
• Reassemble the removed parts in the reverse order.
• Read "Precautions During Work" before reassembling the removed parts.
• If wire bundles are removed or moved during adjustment or part replacement, reshape the wires after completing
the work. Failure to shape the wires correctly may cause problems such as noise.
PANEL SIDE
TOP PANEL
See "DISASSEMBLY"
1. TOP PANEL
and "EXPLODED VIEW"
TOP PANEL
Ref. No. of EXPLODED VIEW : 31
NFC PCB
FRONT PANEL ASSY TUNER

See "DISASSEMBLY" See "DISASSEMBLY"
2. FRONT PANEL ASSY 5. TUNER
and "EXPLODED VIEW" and "EXPLODED VIEW"
FRONT L PCB DAB PCB
Ref. No. of EXPLODED VIEW : 23 Ref. No. of EXPLODED VIEW : 47
FRONT PCB TUNER DAB
FRONT R PCB TUNER
USB PCB
SHIELD COVER
See "DISASSEMBLY"
CD MECHA ASSY 6. SHIELD COVER
See "DISASSEMBLY" and "EXPLODED VIEW"
3. CD MECHA ASSY TOP SHIELD COVER
and "EXPLODED VIEW" Ref. No. of EXPLODED VIEW : 30
CD MECHA
CD PCB SMPS PCB BACK CHASSIS ASSY
Ref. No. of EXPLODED VIEW : 37 See "DISASSEMBLY" See "DISASSEMBLY"
7. SMPS PCB 8. BACK CHASSIS ASSY
and "EXPLODED VIEW" and "EXPLODED VIEW"
MECHA SUPPORT L/R SMPS PCB BACK CHASSIS
See "DISASSEMBLY" Ref. No. of EXPLODED VIEW : 55 Ref. No. of EXPLODED VIEW : 52
4. MECHA SUPPORT L/R
and "EXPLODED VIEW"
MECHA SUPPORT L/R MAIN PCB ASSY
Ref. No. of EXPLODED VIEW : 36 See "DISASSEMBLY"
9. MAIN PCB ASSY
and "EXPLODED VIEW"
CNT PCB
MAIN PCB
NETWORK PCB
MODULE CY920
INPUT PCB
BACK GUIDE PCB
OPTICAL PCB
13
Explanatory Photos for DISASSEMBLY
• For the shooting direction of each photos used in this manual, see the photo below.
• A, B, C and D in the photo below indicate the shooting directions of photos.
• The photographs with no shooting direction indicated were taken from the top of the unit.
• Photos of M-CR611 N1B are used in this manual.
The viewpoint of each photograph
(Shooting direction : X) [View from the top]
↓Shooting direction: B↓
Front side
↑Shooting direction: C↑
↓Shooting direction: D↓
↑Shooting direction: A↑
14
1. TOP PANEL
Proceeding : PANEL SIDE → TOP PANEL
(1) Remove the screws. Remove the connector wire.
x2 x4
CN222
↑Shooting direction: D↑ ↑Shooting direction: A↑ ↑Shooting direction: C↑
2. FRONT PANEL ASSY

Proceeding : PANEL SIDE → TOP PANEL → FRONT PANEL ASSY
(1) Open the CD tray and remove WINDOWS LOADER.
View from the bottom
View from the CD MECHA bottom
(2) Remove the screws.
x2 x2 x2
(3) Remove the screws. Remove the CORD HOLDERs and connector wires. Remove the connector wire.
x2
CP800
ALUMINUM TAPE x5
ACETATE TAPE
From R side From L side
15
3. CD MECHA ASSY
Proceeding : PANEL SIDE → TOP COVER → FRONT PANEL ASSY → CD MECHA ASSY
(1) Remove the screws. Remove the connector wire and FFC.
x3
x4
FFC
CN703
(2) Remove the FFC cable after the CD mecha's short circuit pattern for LD damage prevention has been short circuited.
Be sure to wear an earth band.
FFC
Soldering place
4. MECHA SUPPORT L/R

Proceeding : PANEL SIDE → TOP PANEL → FRONT PANEL ASSY → CD MECHA ASSY → MECHA SUPPORT L/R
See "EXPLODED VIEW" for instructions on removing the MECHA SUPPORT L/R.
5. TUNER
Proceeding : PANEL SIDE → TOP PANEL → TUNER
See "EXPLODED VIEW" for instructions on removing the TUNER.
16
6. SHIELD COVER
→ TUNER → SHIELD COVER
x2
x2 x2
x2
↑Shooting direction: D↑ ↑Shooting direction: A↑
7. SMPS PCB
→ TUNER → SHIELD COVER → SMPS PCB
(1) Remove the screws. Remove the connector wire.
CN223
x4
CN411
CN801
17
8. BACK CHASSIS ASSY
→ TUNER → SHIELD COVER → SMPS PCB → BACK CHASSIS ASSY
Shooting direction: A
x9
x1 x1
x2
9. MAIN PCB ASSY

Proceeding : PANEL SIDE → TOP COVER → FRONT PANEL ASSY → CD MECHA ASSY → MECHA SUPPORT L/R
→ TUNER → SHIELD COVER → SMPS PCB → BACK CHASSIS ASSY → MAIN PCB ASSY
x2
x3
18
NOTES ON HANDLING AND REPLACEMENT OF THE LASER PICK-UP
1. Protection of the LD
Solder a part of the LD circuit to short-circuit. After connecting the circuit, remove the soldering form. Precautions when
handling the laser CD mechanism
2. Precautions when handling the laser CD mechanism

• Be careful not to expose the laser pick-up to dust.
• Do not leave the laser pick-up bare. Be sure to cover it.
• If dust adheres on the laser pick-up lens, blow it off with a blower brush.
• Do not apply shock to the laser pick-up.
• Do not watch the light of the laser pick-up.
3. Cautions on assembling and adjustment

• Be sure that the bench, jig, head of soldering iron (with ceramic) and measuring instruments are well grounded.
• Workers who handle the laser pick-up must be grounded.
• The finished mechanism (prior to anchoring in the set) should be protected against static electricity and dust.
The mechanism must be stored where abnormal external force is not applied.
• When carrying the finished mechanism, hold it by the chassis body.
• Do not use or store the mechanism where corrosive gas such as H2S, SO2, NO2 and CI2 or toxic gas may be gener-
ated, or where substances especially organosilicon, cyanide, formalin and phenolic materials exist. In particular, make
sure that these substances which generate toxic gas do not exist in the set. This may cause the motor not rotating.
4. Determining whether the laser pick-up is defective

• Check the Iop (Laser drive current). Check lop in "SPECIAL MODE". (See page 27)
• If the present Iop (current) value is 60 mA or higher, replace the Traverse unit with a new one.
• No mechanical adjustment is necessary after the replacement.
Protective soldering place for laser diode.

(Connect the connector, and disconnect before powering the APC circuit)
19
SPECIAL MODE
Special mode setting button
b No. 1 - 13： Insert the power plug while pressing button "A", and wait for more than 3 seconds.
Select the mode using the "CURSOR d" and "CURSOR f" buttons, and press the "Enter" button to enter.
b No. 14 - 15： Insert the power plug while pressing button "A", and wait for more than 3 seconds.
b No. 16： Insert the power plug while pressing buttons "A" and "B" together, and wait for more than 3 seconds.
Press and hold the respective buttons to enter your desired mode until the "Standby Indicator" button lights up.
No. Mode Button A Button B Descriptions
Mode used to overwrite the firmware during production.
1 Fuctory Update Mode X -
This is not used during servicing.
MAC address rewrite mode
2 MAC address rewrite mode X -
The firmware version is shown on the display.
3 Version display mode X -
(See page 23)
Mode used during production.
4 Product mode 1 X -
5 Product mode 2 X -
(This is not used during servicing.)
6 Protection history display mode X - Displays the protection occurrence history. (See page 28)
Mode used for development.
7 DPMS forced up date mode X -
Mode used for development.
8 Access to development server mode X -
9 CD test mode X - Servo adjustment, laser current(See page 25)
10 Heat Run mode X -
(This is not used during servicing.)
11 CY920 rewrite mode X -
12 USB Update mode X - Switches this unit to USB Update mode. (See page 31)
Differences with factory initialization are as below. s
•Does not clear the version information such as rewriting failed log.
13 User initialized X -
•Does not clear the history of protection.
•Network devices are started and initialized. (See page 22)
14 232C forced up date mode iOS -
Mode used when this unit cannot be recovered.
15 USB forced up date mode WPS -
Forcibly switches this unit to USB update mode. (See page 33)
Restores to the default settings.
bThe Recently Played list will not be initialized. (See page 21)
16 Factory Initialization mode iOS WPS
bBe sure to do the "User Initialization" after the "Factory Initial-
ization".d
Cursor
Cursor
WPS iOS
20
1. Factory Initialization Mode
The setting values are initialized. See "Initialization Items (Default setting)".
After initialization, the Unit returns to normal mode.
CAUTION
Clears the version information such as rewriting failed log.
Clears the history of protection.
Initial value of laser current and the accumulated laser on time are not cleared.
Power failure flag is not cleared.
Can't erase the Recently Played list.
1.1. Operations
Press and hold the "WPS" and "iOS" buttons on the rear panel before inserting the power plug, then insert the power
plug while holding down the buttons and wait for more than 3 seconds.
Release the "WPS" and "iOS" buttons when the Standby Indicator lights. The unit switches to the factory initialization
mode.
Startup display
All indicators light (2 seconds)：Standby indicator lights green
↓
All off(2 seconds)
↓
Standby indicator lights orange (4 seconds)
↓
"Factory Reset" is displayed for 5 seconds.
Initialization Items (Default setting)

Default
source Internet Radio
DBB OFF
BASS 0 dB
TREBLE 0 dB
BALANCE CENTER
DIMMER 100%
VOLUME 5
TUNER Preset (Favorite list) Clear all
Favorite list Clear all
Clock 00:00 (Except NA) 12:00AM (NA)
TIMER (EVERYDAY/ONCE) Timer function CD
ON TIME 0:00 (Except NA) 12:00AM (NA)
OFF TIME 0:00
Speaker Response Flat
Bi-Amp Disable
iPod mode From iPod
Auto-Standby ON (EU), OFF (Except EU)
Protection history NO PROTECT
Auto Adjust Time Zone:+1h (EU),+9h (JP)
Summer Time:Off (0h)
Network setting DHCP (On)
Network Control OFF
21
2. User Initialization Mode
The setting values are initialized. See Initialization Items (Default setting).
After initialization, the Unit returns to normal mode.
CAUTION
The following 3 points are different from the Factory Reset.
• Does not clear the version information such as rewriting failed log.
• Does not clear the history of protection.
• Network devices are started and initialized. s
2.1. Operations
Press and hold the power operation button "X" before inserting the power plug, then insert the power plug while hold-
ing down the button and wait for more than 3 seconds.
Select "Initialize" using "CURSOR d" and "CURSOR f", then press the "Enter" button to select.
Startup display
"Initialized" is displayed for 5 seconds.
Wait for more than 90 seconds after "Initialized" is displayed and then turn the power off. s
(During this time, start and initialize the network devices.)
22
3. Version Display Mode
The unit functions normally. The item "Version" is added to the menu.
3.1. Starting up
Select "Version Check" using "CURSOR d" and "CURSOR f", then press the "Enter" button to select.
Startup display
"Version" is displayed for 5 seconds.
3.2. Version display

Press the "Input" button, and use "CURSOR 1" and "CURSOR 0" to select (press the "Enter" button) the Version within
the Setup items.
3.3. Display Order

q system μ -com Version → w system μ-com (Boot Loader) Version
→ e Network u-com (Boot Loader) Version → r Network u-com (image) Version
→ t Serial No → y Bluetooth Mac Address
Select "Version" in the "Setup".
"ENTER"
q system μ -com Version：
The version of the System u-com is displayed.
"CURSOR f"
w system μ -com (Boot Loader) Version：
The version of the boot loader System u-com is displayed.
"CURSOR f"
e Network u-com (Boot Loader) Version：
The version of the boot loader Network u-com is displayed.
"CURSOR f"
23
r Network u-com (image) Version：
The version of the image Network u-com is displayed.
When Network Module CY920 startup is incomplete
"CURSOR f"
t Serial No：
MZ_：Fixed characters・b：Last digit of year・cc：Week number・dddddd：Serial number
"CURSOR f"
y Bluetooth Mac Address：
Displays the Bluetooth Mac Address
24
4. CD test mode
4.1. Operations
Select "CD Test Mode" using "CURSOR d" and "CURSOR f", then press the "Enter" button to select.
Startup display
"CD Test Mode" is displayed for 5 seconds.
CD TEST MODE indicator (when disc is loaded)

Remove the power plug to exit this mode.
4.2. Before starting the test

Open the tray and set the disc.
Even when a disc is already set, open and close the tray before the test.
4.3. Servo check

Press "1/3" button. Execute the following steps.
z Press and hold the "1/3" button continuously for over 1 second to skip to SUB CODE readout in step t. "INPUT" but-
ton to return to "0 CD TEST MODE".
"1/3"
q LD ON
"1/3"
w FOCUS ON
"1/3"
e CLV ON
"1/3"
25
r TRACKING ON
"1/3"
t SUB CODE readout (playback sound output)
The BER (Block Error Rate) generated for 1 second time is displayed.
"CURSOR 0" "CURSOR 1"
"CURSOR 0" "CURSOR 1"
The unit moves to the inner circumference (IN), middle circumference (MID) and outer circumference (OUT) positions for
playback and performs the error count.
4.4. Pickup movement

When CD test mode is ready to start, press the "CURSOR 1" / "CURSOR 0" button to move the pickup in FWD (outwards)
or REV (inwards) direction.
Release the button to stop the pickup. (The pickup keeps moving while the button is pressed.)
You can also stop the pickup by pressing the "CURSOR 0"button. After the inner switch is set to on, the pickup stops.
26
4.5. "All servo on" and "Auto Adjustment"
Press the "CURSOR d" button to turn on the all servos and perform auto adjustment. After auto adjustment completes,
the playback operation starts. (playback sound is output)
Stop (stop to the playback state after auto adjustment)
Press the "SOURCE" button to stop the playback operation and servo. The following screen will be displayed.
After stopping, the auto adjustment values will be read.
Adjustment value display (After turning on the all servo and performing auto adjustment)
Press the "SOURCE" button, after turning on the all servo and performing auto adjustment.
When "CURSOR d/f" button is pressed, the adjustment values are displayed in the following order.
qFOCUS BALANCE
wFOCUS GAIN
eTRACKING BALANCE
rTRACKING GAIN
tFOCUS OFFSET
yTRACKING OFFSET
uRFRP
(Caution) If you have not completed the adjustment, the displayed values are not correct.
4.6. Displaying the laser current

In CD TEST MODE, press and hold the "VOLUME d" button for over 1 second to turn on the laser and measure the laser
current.
The laser drive current undergoes A/D conversion for calculation. Figures below decimal point are omitted.
The current value is updated every 3 seconds.
Press the "SOURCE" button, to return to the CD TEST MODE screen.
Stored data is not cleared, even when the Unit is reset(Factory/User).
Overwriting the stored data

With the laser current displayed, press and hold the "1/3" button for over 5 second to save the current value on EEPROM
(overwrite the stored data).
After overwriting, the laser current appears again. Rewriting is performed upon shipment from the factory and when the
mechanism is replaced.
The Count value is reset upon shipment from the factory and when the mechanism is replaced.
27
4.7. Displaying the accumulated laser-on time
In CD TEST MODE, press and hold the "Volumef" button for over 1 second to display the accumulated laser-on time.
The laser drive time is added and the result is displayed.

Time counting is executed every 10 minutes and the counted value is displayed in 1 hour increments. Displays up to
10922 hours.
Press the "SOURCE" button, to return to the CD TEST MODE screen.
The count values are not cleared, even when the set is reset (Factory/User).
Resetting the count value

With the accumulated laser-on time displayed, press and hold the "1/3" button for over 5 second to reset the count
value (overwrite the stored data).
5. Protection History Display Mode

5.1. Operations
Select "Protection History" using "CURSOR d" and "CURSOR f", then press the "Enter" button to select.
Startup display
"Detect Protection" is displayed for 5 seconds.
Remove the power plug to exit this mode.

(a) No detected history
(b) Thermal error detection
Detects abnormal temperature raises in D-AMP (TAS5142)
28
(c) Speaker short protection
Detected that the potential difference between both ends of the speaker terminal became DC
± 3V or more.
(d) Over current
Detected over-current for the digital amplifier(TAS5142).
(e) DC protect 1
Power-line short-circuit.(+29V(D-AMP power))
(f) DC protect 2
Power-line short-circuit.(+12V_D, +12V_A, -12V, +5V)
Resetting the protection history

With the protection history displayed, press and hold the "CURSORd" button for over 5 seconds to clear the protection
history.
After the history is cleared, "No Protection" is displayed.
Protection history is not cleared, even when the set is reset (User Reset).
29
PROCEDURE AFTER REPLACING THE MICROPROCESSOR, ETC.
The procedure after replacing the u-COM (microprocessor), flash ROM, etc. is as follows.
Proce-
dure after
PCB Name Ref. No. Description Remark
Replace-
ment
MAIN IC112 R5F56108VNFP B
SOFTWARE : SYSTEM
EXPLODEDd 40,24, ★ d CY920 MODULE ASSY D Also be sure to replace the NFC Module at the
same time.
b1 The firmware for the CY920 MODULE is written to the INTERNAL ROM of the CY920 and the IC812 (EXTERNAL ROM) of the DIGITAL
circuit board.
"CY920 Error" appears in the display if the DIGITAL PCB or the CY920 is replaced, as this results in the version of the INTERNAL ROM
differing from that of the EXTERNAL ROM.
In this case, see "Update Procedure in the Event of a CY920 Error".
(This does not require special operations such as pushing multiple buttons at the same time. The firmware also cannot be updated via
DPMS.)
Procedure after Replacement

A : The software has been written. The software is not written at the time of replacement.
B : The software has been written. The software may need to be rewritten by version updates. Check the version.
C : The software has not been written. The software needs to be written after replacement.
See "Firmware Update Procedure" for information on writing the software.
D : The software has been written. Be sure to rewrite with the latest software for your service region.
See "Firmware Update Procedure" for information on writing the software.
30
FIRMWARE UPDATE PROCEDURE
1. Updating via USB
The latest firmware can be downloaded to a USB memory for updates.
1.1. Connecting to the USB Memory
(1) Preparation
• Use a memory that supports USB2.0.
• USB format : Prepare a USB memory formatted in FAT16 or FAT32.
• Do not run the USB memory through a hub.
• Do not connect a computer to the USB port of this unit using a USB cable.
• Do not use an extension cable when connecting the USB unit.
• If a USB memory device cannot be updated, replace it with a different USB memory device and perform the update
again.
1.2. Unzipping the Downloaded File

Unzip the downloaded file on your computer.
MCRXXXXXXX USB_MCR-XXXXXXX_XXXXXXXXXXXX-XXXX.zip
copy to USB flash drive
The "firmwares" folder is created upon unzipping the file.

Copy that folder to USB flash drive.
The "firmwares" folder must be in the root directly of the USB flash drive (memory).
31
1.3. File structure on USB Memory
Copy the update files to the USB memory with the following structure.
USB memory root
Model Name Model Area Product ID
North America (U) 100200090100

Europe (N) 100200090200
M-CR611
China (K) 100200090500
Japan (F) 100200090400
+ firmwares
+ X00200XXXXXX
+ enc_update.xml
+ IMG.bcd
+ SBL.bcd
+ SYS.bin
1.4. Insert the USB memory into the USB port.

NOTE : Remove the LAN cable from this unit when performing updates.
Download ﬁrmware
in USB ﬂash drive.
1.5. Start the update.

Press and hold the power operation button before inserting the power plug, then insert the power plug while holding
down the button and wait for more than 3 seconds.
Select "USB Update" using "CURSOR d" and "CURSOR f", then press the "Enter" button to select.
1.6. Display during USB update

The following message appears on the display.
Display
1.7. Press the "ENTER" key on the remote control unit or this unit.
Then start Firmware Update.
Display
32
1.8. The firmware update finishes.
The unit restarts after the update is finished.
---Cautions on Firmware Update---

• Wait 60 seconds before turning the power on again( AC ON → OFF → ON ).
• Never remove the USB memory before the update is finished.
• Do not turn off the power until updating is completed.
Approximately 30 minutes is required for the updating procedure to be completed.
Once an update is started, normal operations cannot be performed until it is completed.
Also, setting items may be initialized.
Note down the settings before updating, and set them again after updating.
2. Forced USB All Device Write Mode

2.1. Actions
Mode used when this unit cannot be recovered.
Forcibly switches this unit to USB update mode.

Perform the procedures in steps 1.1 to 1.4.
2.3. Operations
Press and hold the "WPS" button on the Rear panel before inserting the power plug, then insert the power plug while
holding down the button and wait for more than 3 seconds.
Select "USB Update" using "CURSOR d" and "CURSOR f", then press the "Enter" button to select.
2.4. Forced USB All Device Write Mode

The following message appears on the display.
Display
2.5. The firmware update finishes.

Restart after the update, and all devices are updated.
3. Update Procedure in the Event of a CY920 Error

3.1. Actions
Perform the following update procedure if "CY920 Error" appears in the display when the power is turned on after replac-
ing the CY920.

Perform the procedures in steps 1.1 to 1.4.
3.3. Operations
(1) Remove the AC power plug and turn off the power.
(2) Copy the update file to a USB memory device and insert the USB memory device in the USB port.
(3) Insert the AC plug and turn on the power.
(4) The update starts automatically after "CY920 Error" appears in the display.
(5) The firmware update finishes.

The unit restarts after the update is finished.
(6) After the update, check that "CY920 Error" is no longer displayed, and check the version of the new firmware.
See "1. Version Display Mode" (20 page ).
33
4. Updating via DPMS
Download the latest firmware from our website and update the firmware.
4.1. Network Connection
(1) System Requirements
• Internet Connection by Broadband Circuit
• Modem
• Router
• Ethernet cable (CAT-5 or greater is recommended)
(2) Setting
Internet
Computer
Modem
ComputerLAN port / Ethernet connector
To WAN port
Router
To LAN port
To LAN port
Ethernet connector of this Unit
4.2. Check and update the firmware

Check if there is a firmware update available. It is also possible to check approximately how long the update will take.
(1) Turn on the power pressing "X" button.

(2) Press "INPUT" and "Cursor 0/1" buttons select to "Setup". Press "ENTER" button.
• Press "Cursor d/f" buttons select to General For "General". Press "ENTER" button.
• Press "Cursor d/f" buttons select to "Firmware". Press "ENTER" button.
• Press "Cursor d/f" buttons select to "Update". Press "ENTER" button.
• Press "Cursor d/f" buttons select to "Check for Update".
(3) Press the "ENTER" button.
• The latest version of the firmware uploaded to the web is displayed.
• If the latest firmware version is on the web, proceed to (4).
• If the latest firmware is already installed, press the "INPUT" button to close the Update menu.
(4) Press "ENTER" button. Select "YES", then press "ENTER" button.
(5) Firmware Update will be started.
---Cautions on Firmware Update---

• For the update procedure, a proper broadband Internet connection environment and settings are required.
• Do not turn off the power until updating is completed.
• It takes around 1 hour to complete the update.
Once an update is started, normal operations cannot be performed until it is completed.
The GUI menu settings and image adjustment settings of this unit may be initialized.
Note down the settings before updating, and set them again after updating.
34
5. Error code table f
• Preparation operation rewritten, Update error code checking.
ErrCode DPMS Update
Hex The occurred event FL Message
01 Login failed（DPMS Access Login Incorrect notification） Login failed 01
02 Login failed（DPMS Access Server Busy information） Server is busy 02
03 Login failed（DPMS Access link failure information） Connection fail 03
04 Firmware Individual information acquisition failure Connection fail 04
05 Firmware Individual information acquisition TimeOut Connection fail 05
06 Firmware all information acquisition failure Connection fail 06
07 Firmware all information acquisition TimeOut Connection fail 07
08 Error notification received at the time of Firmware Info request Connection fail 08
09 Firmware Info response acquisition Time Out Connection fail 09
0A Firmware Down Load failed（(NG）information recieved） Download fail 0A
0B Firmware Down Load failed（(ServerBusy）information recieved） Download fail 0B
0C Firmware Down Load failed（(Connection failed）information recieved） Download fail 0C
0D Received Package Version is wrong Connection fail 0D
20 Transition to the Boot Loader Mode（Failure to acquire the IP Address（AutoIP）） Connection fail 20
21 Transition to the Boot Loader Mode（Failure to acquire the IP Address（TimeOut）） Connection fail 21
22 Transition to the Boot Loader Mode（DDPMS Access Login Incorrect notification） Login failed 22
23 Transition to the Boot Loader Mode（DPMS Access Server busy infomation） Server is busy 23
Transition to the Boot Loader Mode (DPMS Access connection failed i nformation
24 Connection fail 24
recived）
25 Transition fails to Boot Loader Mode Connection fail 25
27 Write failure to the Boot Loader Mode to transition after the EEPROM Connection fail 27
• Firm error codes at the main microprocessor rewritten.

ErrCode DPMS Update
Firm Info response acquisition Time Out (Main rewrite Firmware recived failure (Time
10 Updating fail 10
Out))
11 Firm Info response acquisition recived error (Main rewrite Firmware recived failure (Error) Updating fail 11
Firm Info response acquisition recived error (Main rewirte Firmware recived data incorrect
12 Updating fail 12
(Check Sum Error))
13 Rewrite failure (Block Erase failued before Main rewriting ) Erase fail 13
14 Rewrite failure (Block Write failued before Main rewriting) Updating fail 14
15 Rewrite failure (Verify incorrect after Main rewriting) Updating fail 15
22 Transition to the Boot Loader Mode (DPMS Access Login Incorrect notification) Login failed 22
23 Transition to the Boot Loader Mode (DPMS Access Server busy infomation) Server is busy 23
24 Transition to the Boot Loader Mode (DPMS Access connection failed infomation) Connection ｆ ail 24
39 Login failure (DPMS Access access Time Out) Connection ｆ ail 39
3A Down Load failure (Download error (NG)information recieved) Download fail 3A
3B Down Load failure (Download error (Server Busy) information recieved) Server is busy 3B
3C Down Load failure (Download error (connection failed)information recived) Connection fail 3C
3D Transition to the Boot Loader Mode (Failure to acquire the IP Address (Auto IP)) Connection ｆ ail 3D
3E Transition to the Boot Loader Mode (Failure to acquire the IP Address (Time Out)) Connection ｆ ail 3E
3F Fail in moving into Boot Loader Mode. Connection fail 3F
• CX920 error codes when firmware rewriting.

ErrCode DPMS Update
A0 Failure to acquire the IP Address（AutoIP） Connection ｆ ail A0
A1 Failure to acquire the IP Address（TimeOut） Connection ｆ ail A1
A2 Login failed（DPMS Access Login Incorrect notification） Login failed A2
A3 Login failed（DPMS Access Server busy infomation） Server is busy A3
A4 Login failed（DPMS Access connection failed infomation） Connection ｆ ail A4
A6 Error notification received at the time of Firmware Info request Updating fail A6
A7 Firmware Info response acquisition Time Out Updating fail A7
AE Down Load failure (Download error (NG)information recieved) Download fail AE
AF Down Load failure (Download error (Server Busy) information recieved) Download fail AF
B0 Down Load failure (Download error (connection failed)information recived) Download fail B0
B1 Down Load failure（Error at the time of Download（TimeOut）） Download fail B1
B2 Firmware Down Load failed Updating fail B2
B4 Transition fails to Boot Loader Mode Updating fail B4
B5 Transition fails to Application Mode Updating fail B5
35
TROUBLE SHOOTING
1. OLED dose not light
Check Power Supply Voltages for SMPS.

Check the following voltages when the unit is connected to the AC
power supply.
SMPS PCB
NG
• CN221 : 1 pin Pulse signal of 50 or 60 Hz of 4 V(P-P) Replace the SMPS PCB.
• CN221 : 9 pin 5 V
• CN221 : 11 pin 20 V
If these voltages are not output, a fault may have occurred in the
SMPS PCB. Furthermore, the voltages of pins within CN221 other than
those listed above are only output when the power is ON.
OK
Check Power Supply Voltages for System μ-com. NG Check Soldering or replace for the following parts.
MAIN PCB • CP103 : 9 pin
• +STBY 5 V CP103 : 9 pin • SMPS PCB
OK
Check Reset signal for Main μ-com. Check Soldering or replace for the following parts.
NG • IC112, IC117
MAIN PCB
• IC112 : 19 pin RESET
"Hi" level O.K.?
OK
Check Oscillation waveform.

NG
MAIN PCB Check Soldering or replace for the following parts.
• IC112 : 20 pin • X102 on MAIN PCB
12MHz OK?
OK
Check Power Supply Voltages for OLED. Check Soldering or replace for the following parts.
MAIN PCB NG • IC114 on MAIN PCB
• CP103 : 11 pin +18V_OLED • FPC104 on MAIN PCB
• FPC104 : 10 pin, 12 pin +16V_OLED • FPC1 on DISPLAY PCB
• FPC104 : 8 pin +3.3V_OLED • FPC2 on DISPLAY PCB
OK
Check Soldering or replace for the following parts.
• IC112 on MAIN PCB
Check Drive Signals for OLED. NG • IC116 on MAIN PCB
DISPLAY PCB • Q133 on MAIN PCB
• FPC1 : D0 to D7, EL_RD, EL_RW, EL_DC, EL_CS, EL_RST • FPC1 on DISPLAY PCB
• OLED MODULE
END
36
2. No Sound. Noise generated
2.1. COMMON (signal)
Check Digital Audio Data output from CODEC.

NG
• IC107 : 1
7, 18, 19, 20 pin • IC107 : 17, 18, 19, 20 pin on MAIN PCB
DIR_LRCK, DIR_SCLK, DIR_SDATA, DIR_MCLK
OK
Check Digital Audio Data input for PWM CONTROLLER.

NG
• IC108 : 1
1, 22, 23, 24, 26 pin • IC108 : 11, 22, 23, 24, 26 pin on MAIN PCB
MCLK, LRCK, SCLK, SDIN1, SDIN2_1
OK
Check the PWM waveform output of PWM CONTROLLR using an 2.1.A

oscilloscope. PWM waveform (square wave) is not output.
NG Fault in the DIR (PCM9211) or PWM CONTROLLER
AMP PCB
• PF103 : 2
, 4 pin (Lch, SPK-B) (TAS5558). Check“2.2. COMMON (power supply, com-
6, 8 pin (Lch, SPK-A) munication line)”,and then replace the IC108 (TAS5558)
10, 12 pin (Rch, SPK-B) if there are no faults.
14, 16 pin (Rch, SPK-A)
2.1.B
Check the waveform of the terminals above when the input function
NG PWM waveform (square wave) is disrupted.
is "Analog" and in a state "Volume 1" or higher.
There is a high probability there are some faults in IC500
If an approximate 3.3VP-P square wave can be confirmed at each
and IC502 (TAS5142).
terminal, there are no problems with DIR (PCM9211) and the PWM
Replace the IC500 and IC502 (TAS5142).
CONTROLLER (TAS5558).
If the fault still occurs after replacement, check“2.1.A”.
OK
2.1.C
No fault was detected in the PWM waveform at each terminal.
Check the PWM output of IC41, IC42 (TAS5142).
• L502 : TAS5142 side terminal (Rch, SPK - B)
• L503 : TAS5142 side terminal (Rch, SPK - B)
• L504 : TAS5142 side terminal (Rch, SPK - A)
• L505 : TAS5142 side terminal (Rch, SPK - A)
NG
• L510 : TAS5142 side terminal (Lch, SPK - B)
• L511 : TAS5142 side terminal (Lch, SPK - B)
• L512 : TAS5142 side terminal (Lch, SPK - A)
• L513 : TAS5142 side terminal (Lch, SPK - A)
A test terminal or cable needs to be attached to the bottom side of
the AMP board to measure the waveform of each terminal.
There are no faults in the IC500 or IC502 (TAS5142) if an approx.
29VP-P square wave is confirmed at each terminal.
OK
No faults
Identify the input function from which sound is not output or from
which noise occurs, and then check the troubleshooting sections
from 2.3 onwards.
37
2.2. COMMON (POWER Control signal)
Check Power Supply Voltages for DIR.

NG
• IC107 : 46pin +5V_A • IC110 : IN : +12V_A / OUT : +5V_A
• IC107 : 22, 36, 42pin +3V_D1 • IC113 : IN : ST+5V / OUT : +3V_D1
O.K.? •MAIN PCB
OK
Check Power Supply Voltages for PWM CONTROLLER.AMP PCB.

NG
• IC108 : 9
, 14, 35, 50 pin • R325 : +3V3_5558
+3.3V_5558 OK?
OK
Check Power Supply Voltages for AMP IC.

AMP PCB Check Soldering or replace for the following parts.
• IC500, IC502 : 1, 36, 18, 19 pin NG
• PF103 : 7 pin : +12V_5142
+12V_5142 OK? • CN500 : 1, 2, 5, 6 pin : +29V
• IC500, IC502 : 21, 26, 29, 34 pin •AMP PCB
+29V OK?
OK
Check Reset signal for DIR.

NG
• IC107 : 3
4pin DIR_RESET • IC112 : 68pin DIR_RESET on MAIN PCB
"Hi" level O.K.?
OK
Check Reset signal for PWM CONTROLLER.

NG
• IC108 : 1
1pin RESET • IC112 : 77pin 5558 RESET on MAIN PCB
"Hi" level O.K.?
OK
Check Reset signal for AMP IC.

NG Check Soldering or replace for the following parts.
AMP PCB
• IC108 : 37 pin VALID on MAIN PCB
• IC500, IC502 : 5,15, 15pin VALID
• PF103 : 15 pin Reset
"Hi" level O.K.?
OK

NG
• IC107 : 4
0 pin TXO • X101 on MAIN PCB
24.576 MHz OK?
OK

MAIN PCB NG Check Soldering or replace for the following parts.
• IC108 : 1
1 pin MCLK • IC107 : 20 pin → IC108 : 63 pin DIR, MCLK
MCLK OK?
OK
38
Check control signal for DIR.
MAIN PCB
• IC112 : 86, 87, 88, 89 pin → IC107 : 23, 24, 25, 26 pin
• IC107 : 2
3, 24, 25, 26 pin
DIR_DO, DIR_DI, DIR_CLK, DIR_CE
DIR_DO, DIR_DI, DIR_CLK, DIR_CE
OK
Check control signal for PWM CONTROLLER.

MAIN PCB
• IC108 : 2
0, 21 pin NG Check Soldering or replace for the following parts.
SDA, SCL • IC112 : 82, 83pin
• IC108 : 1
8, 14pin SDA, SCL on MAIN PCB
PDN, MUTE • IC108 : 77, 79, 80 pin A_PWM_RST, A_PWM_PDN,
"Hi" level O.K.? A_PWM_MUTE on MAIN PCB
END
39
2.3. CD playback
Check Power Supply Voltages for CD.

CD PCB
NG CD PCB
• CN703 : 4 pin +12V_D
• CN703, IC705, IC704
• IC705 : IN +12V_D / OUT : +7V5_D1
SMPS PCB
• CN703 : 2 pin D+5V
• IC441
• IC704 : IN D+5V / OUT : A+3V
OK
Check Power Supply Voltages for CD. NG

CD PCB
• IC703 on CD PCB
• IC703 : 2 pin OUT 1.5V OK?
OK
Check Reset signal for CD.

CD PCB NG
• IC701 : 69pin /RST "Hi" level O.K.? • IC112 : 115pin DECRST on MAIN PCB
OK

NG
CD PCB Check Soldering or replace for the following parts.
• IC701 : 4
9 pin XO • X701 on CD PCB
16.9344 MHz OK?
OK
Check Digital Audio Data Input for CODEC. NG Check Soldering or replace for the following parts.
MAIN PCB • IC701 : 33pin CD_SPDIF on CD PCB
• IC107 : 30 pin CD_SPDIF • IC107 : 30pin CD_SPDIF on MAIN PCB
• CN702 : 20 pin CD_SPDIF
OK
END
40
2.4 . TUNER (U / F / K Only)
Check Power Supply Voltages for TUNER. NG Check Soldering or replace for the following parts.
INPUT PCB • IC110 : IN : +12V_A / OUT : +5V_A on MAIN PCB
• TM1 : 3 pin +5V_A • CP106 : 17 pin A+5V on MAIN PCB
OK
Check Analog Audio Data output from TUNER PACK. NG Check Soldering or replace for the following parts.
INPUT PCB
• C63, C65
• TM1 : 1 pin : L-OUT / 2pin : R-OUT
OK
Check the Output form Analog selector. NG Check Soldering or replace for the following parts.
• IC2 : 2, 9 pin : IN1 A, IN1 B • IC112 : 17 pin AIN_CNT1
: 5 pin : CNT1 [L]
OK
NG
Check the DIR input. Check Soldering or replace for the following parts.
• IC107 : 47, 48 pin : L_CH / R_CH on MAIN PCB • C62, C63 on INPUT PCB
OK
to 2.1. COMMON(signal)
2.5 . TUNER (N Only)

Check Power Supply Voltages for TUNER. NG • IC801 : IN +5V
DAB PCB • L802
• IC801 : OUT 3.3V • CP2 : +5V on INPUT PCB
• IC111 : 1 pin +5V on MAIN PCB
OK
Check Digital Audio Data output from TUNER PACK. NG Check Soldering or replace for the following parts.
DAB PCB
• R811
• CP803 : 26 pin : SPDIF
OK
NG
• IC107 : 32 pin • CP106
OK
41
2.5. Analog In 1
Check Analog Audio Signal from Analog1. NG

INPUT PCB
• JK2
• JK2 : L, R
OK
ALL Model Area

• C75, C82 : (L/R) NG
U / F / K only Check Soldering or replace for the following parts.
• IC2 : 4, 7 pin (L/R) • IC2 : 5 pin AIN_CNT
5 pin : AIN_CNT1 [H]
OK
NG
• IC107 : 47, 48 : L CH / R CH • C62, C63 on INPUT PCB
OK
2.6. Digital In 1/2
Check Power Supply Voltages for OPTICAL Input IC. NG Check Soldering or replace for the following parts.
OPTICAL PCB
• CP3 : 9pin +3.3V
• JK810, JK811 : 3 pin +3.3V
• IC133 : +STBY+5V / OUT : +3.3V
• IC113 : +3.3V
OK
Check Digital Audio Data from OPTICAL Input terminal. NG

MAIN PCB
• JK810, JK811 1pin for the OPTICAL PCB
• IC107 : 33 pin (for OPTICAL1), 35 pin (for OPTICAL2)
OK
42
2.7. USB / ETHERNET / Wi-Fi

Check Power Supply Voltages for Network. NG Network PCB
Network PCB • CP805 : 1, 2, 3 pin : NET_5V
• CP805 : 1, 2, 3 pin : NET_5V • CN223 : 1, 2, 3 pin : NET_5V
SMPS PCB
OK
Check Power Supply Voltages for USB. Check Soldering or replace for the following parts.
Network PCB • IC800, IC811 : 1 pin +5V
• FRONT USB : IC800 : 1 pin +5V NG • CN807 : 1 pin +5V Case of FRONT USB
• REAR USB : IC811 : 1 pin +5V • JK901 (FRONT USB), CP809 (Case of REAR USB)
OK
Check Power Supply Voltages for CY920.

Network PCB
• IC804 on Network PCB
• IC804 : 7 pin +3.3V NG
• IC807 : 7 pin +2.5V
• IC803 : 7 pin +1.8V
• IC807 : 7 pin +1.2V
• CN801 on Network PCB
• CN801 : 61 pin +5V
OK
Check Reset signal for ETHERNET PCB (CY920).

Network PCB
• CN801 : 15 pin
• CN801 : 15pin
• CP813 : 14 pin
"Hi" level O.K.?
OK
Case of PCM signal

Check Digital Audio Data for CODEC. NG Check Soldering or replace for the following parts.
Network PCB Case of PCM signal
• CP813 : 25 pin CY920_MCLK • CP813 : 25 pin CY920_MCLK
• CP813 : 23 pin CY920_BCK/DSD_BCK • CP813 : 23 pin CY920_BCK/DSD_BCK
• CP813 : 24 pin CY920_LRCK • CP813 : 24 pin CY920_LRCK
• CP813 : 21 pin CY920_DATA • CP813 : 21 pin CY920_DATA
Case of DSD signal Case of DSD signal
• CP813 : 23 pin CY920_BCK/DSD_BCK • CP813 : 23 pin CY920_BCK/DSD_BCK
• CP813 : 22 pin CY920_DSDR • CP813 : 22pin CY920_DSDR
• CP813 : 21 pin CY920_DATA/DSDL • CP813 : 21 pin CY920_DATA/DSDL
OK
43
2.8. ANALOG AUDIO OUT
Check the power supply for the STA309A AUDIO processor NG Check Soldering or replace for the following parts.
MAIN PCB MAIN PCB
• IC102 : 3, 12, 44, 52, 59 309_+3.3V_ • IC102 : 3, 12, 44, 52, 59 309_+3.3V_
• IC113 : OUT +3.3V_D1 • IIC113 : OUT
OK
Audio input signal (for PCM) for the STA309A AUDIO processor NG
Check the I2S signal. Check Soldering or replace for the following parts.
• IC102 : 11 pin STA309_BCKO Audio signal (for PCM) for the STA309A AUDIO processor
10 pin STA309_LRCKO • IC102 : 11 pin STA309_BCKO
9 pin STA309_DOUT 10 pin STA309_LRCKO
9 pin STA309_DOUT
Audio signal (for DSD) for the STA309A AUDIO processor • CP102 : 23 pin CY920_BCK/DSD_BCK
Check the DSD signal. • IC107 : 13 pin STA309_LRCKO
• IC2 : 20 pin XTI 14 pin STA309_DOUT
1 pin DSD_BCK
6 pin DSD_R Audio signal (for DSD) for the STA309A AUDIO processor
9 pin DSD_L • IC102 : 20 pin XTI
1 pin DSD_BCK
6 pin DSD_R
9 pin DSD_L
• IC107 : 11 pin DSD_SCKO
• CP102 : 23 pin CY920_BCK/DSD_BCK
22 pin CY920_DSDR
OK 21 pin CY920_DATA/DSDL
• IC103 : 5 pin CLK
NG
Check the PWM output signal of the STA309A AUDIO processor • Replace the IC102 : STA309A
MAIN PCB
• IC102 : STA309A 49, 50 pin PWM waveform L CH
47, 48 pin PWM waveform R CH
OK
NG
Check the Audio output signal of the STA309A AUDIO processor Check Soldering or replace for the following parts.
• IC101 : 7 pin (L CH), 1 pin (R CH) • IC101, IC102
OK
NG
Check the MUTE circuit. Check the MUTE circuit.
MAIN PCB MAIN PCB
• Q106, Q107, Q113, Q114 : 2 pin (BASE) • Q112 : 2 pin (BASE)
or or
• R141,0R142, R150, R151 • IC112 : 72 pin PRE_OUT_MUTE
Make sure the voltage for the points above is Make sure the voltage for the points above is
"Lo" level O.K.? "Lo" level O.K.?
OK
Replace each device.

MAIN PCB
• Q106, Q107, Q113, Q114
44
MEASURING METHOD AND WAVEFORMS
To check the waveforms on the Main board, connect the GND (-) probe of the oscilloscope to the specified reference volt-
age.
Except for lnner SW, TRVSW
NOTES
Measuring Disc : CD/TCD-784
CD-R/TCD-R082W
CD-RW/TCD-W082W
(It is recommended to use extension wires between the probe and test points.)
• When watching the HF waveform, use the extending wire as short as possible.
• When the HF waveform is noisy or the eye-pattern is unidentifiable, replace the Traverse Unit.
• For points q to Q5, take measurements at the points shown in the diagram below.
1. TEST POINT
MAIN PWB：Bside
R150
C146
Q122 Q113 Q114
R178
R183
R142 R151
R204
C147
R219
R141
C358
C357
C167
R520 IC101 Q124 Q106 Q107
R182
R177
R384
R382
R380
NJM8068 IC102
C124
R519 STA309A
C143 C153
R518 R421 C166
R422 R514 R589
R513
R536
R515
R516
R517
R423
C173
C170
C280
R373
R372
R510 R590
C101 C163 C169
C356
C257R345
R344R430
R190R200
L106 R189
R188
15
C259
R343
D115
R273
R271
R270
R470 R187
R546
R545
R544
IC113 R469 R552
R 5 37
R427
R359
R346
R385
C283
R386
AZ1117CH-3.3 R468 R132 R591
R242 53 33
C349
R 5
R614
R
R249 2
R366
2
52
R528
R503 R529
R464 R531
R199 R530
R527
R524
R252
R256
R478
R
R244
R523
R195 R326R328 R463

R315 R146
R160
R157
R465
R466
R467
R473
R400
R396
R243
C203
R223
R261
C197
C258 D122 R277 IC107 R192 R319R321 R461

D117
R417 C274R535 PCM9211

C320 C319 R276
R336C242 R275 C207 R462
C224
C225
R237
R374
R370
R379
R378
R367
R365
R363
R361
R331
R291R292 R460
C231
R318
C229
C279 R225 R304
13
R305R306 R459
C285 R227
C321 C228C227 R228
R255
R299
ICS511
C288 R229
IC103
R313
R615
R390
R376
R230 R296 R311

C289 R285R286
C213
R232
R231
C295 R278 R283

R484 R266R263
C298 R294 R260R258
C316 R253
R184
C317
R481
R485
R247
L124 R391
R254
R389 C184
L129
R233
R234
R257
R259
R262
R479
R480
R235
R500
D108 C209 C210 L128 R239

23.R_OUT
R613
C201 C159C157 22.AGND IC112

C200 R5F56108VNFP
14
L104 R181C156 21.L_OUT
20.AGND
C194
R236
R224
R512 19.AIN_CONT
D102R116 R107
R412
R413
R414
C190
IC108 18.A_+5V
Q103
R226
D101 17.A_+5V
TAS5558DCAR C232 16.DGND
R434
R193
D103 C303 15.TU_INT/DO
R122R131
R130R123
R136
C294 C233
D121 IC104 14.TU_RST
R217R216
R215R214
R437R436
R211 R210
R438R207
R206
NJM4556AM D113 13.TU_CE
12.TU_SDA/DI
11.TU_CLK
11.+18V_OLED
R209
10.TU/DAB_ON C176
12.NFC_ACK
3.POWER_H
9.STBY_+5V
9.ST_+5V
1.P_DOWN
8.ST_+5V
2.BI_AMP
8.D_+12V
4.A_+12V
10.DGND
Q119 D107D105 D112

6.A_-12V
Q109 7.DGND
7.DGND
5.AGND
R439
6.SPDIF
5.WPS_ON
2.AGND
R521 4.OPT2
3.HP_L
1.USB_OE
1.HP_R
3.OPT1 2.FET_5V_ON
R525 2.DGND 3.FET_2V2_ON
R526 1.D_+3V3 4.DC/DC_1V8_ON
5.DC/DC_2V5_ON
6.DC/DC_3V3_ON
R162
R159
R156
R138
R148
R154
7.IOS(WIFI)
R496
R497
C353
8.U_PWR2
9.U_PWR1
10.REAR_USB_SW(OE2)
11.FRONT_USB_SW(OE1)
R327 12.OC_FLAG1
R541
R542
R543
13.OC_FLAG2
R153
R147
R137
Q134
R539
R538
R540
14.E_RST
15.SPI_MOEI
Q136
D114 16.SPI_MIEO
17.SPI_CLK
18.SPI_CS
C352 R498 19.FACT_RST
20.SPI_REQ
D104
Q135
R494 21.CY920_DATA/DSDL
22.CY920_DSDR
2D_+12V
4.D_+5V
D118
1.DGND
3.DGND
5.DGND
Q137 23.CY920_BCK/DSD_BCK
R495
C354
R499
Q108 24.CY920LRCK
25.CY920_MCLK
26.MGND 1.CD_LDCHK
27.MGND 2.CD_CLOSE
3.CD_OPEN
B
4.CD_MSTBY
5.CD_SBSY
FPC106
6.CD_DREQ
7.CD_DECRST
8.CD_INSW
9.CD_CLSW
10.CD_CPSW
11.CD_BUCK
12.CD_CCE
13.BUS0
14.MGND
15.BUS1
16.BUS2
17.BUS3
18.CD_SRAMSTB
19.MGND
20.SPDIF
21.MGND 1.CPU_+3V3
2.TXT_232
33.LED_+5V 34.NC 3.RXD_232
31.LED_RST 32.LED_+5V 4.MGND
C326 29.I2S_SCL 30.I2S_SDA
C325 27.EL_CS 28.DGND
25.EL_RW 26.EL_RST
C323 23.D0 24.EL_DC
C327 21.D2 22.DGND
19.D4 20.EL_RD
C328 17.D6 18.D1
15.DGND 16.D3
C329 13.D7 14.D5
11.KEY1 12.OLED_+16V
C330 9.KEY2 10.OLED_+16V
C331 7.LED_OR 8.OLED_+3V3
5.HP_DET 6.REMOTE
C332 3.LED_GREEN4.CPU_+3V3
1.LED_RED 2.KEY3
R383
C304
Q131
C300
C336
C343 C296
C344 R368
C335
C334
C333
Q133
C284
C297
C290
L123
CD PWB：Bside
BAR CODE LABEL
7
GND
D+5V
GND_DA
+12V_D
GND_DA
11 4
TR-
RD
E
C
GND
FO+
VC
12
A+3.3V
LOAD+
6
D
PD
FO-
LOAD-
B
TR+
9
LD
OP_SW
FCO
GND_DRV
FMO
CL_SW
3
TRO
C
FEI
TEI
CD_LDCHK
CD_CLOSE
VC
CD_OPEN
10
CD_M_MUTE
SP+ CD_SBSY
5
CD_DREQ
CD_DECRST
SP- CD_LMSW
SLED+ CD_CLSW
A
CD_OPSW
RFO
SLED- CD_BUCK
CD_CCE
GND_DRV BUS0
2
GND
LMSW BUS1
RFEQO
BUS2
CD
SRAMSTB
GND
SPDIF
GND
1
DMO
45
No. Symbol No. Symbol Reference voltage
q TP RFEQO Ⓐ C766(+) VC：q - i
w TP RFO Ⓑ CP103(10) DGND：Q3 - Q5
e TP FEI Ⓒ CN704(3) MGND：o - Q2
r R850 FOC1
t TP TEI
y R842 TRO1
u R843 FMO1
i R844 DMO1
o CN705(3) OPSW
Q0 CN705(5) CLSW
Q1 CN705(1) LOAD+
Q2 CN705(2) LOAD-
Q3 R228 LRCK
Q4 R229 SCLK
Q5 R227 SDATA
2. WAVEFORMS
1. DISC PLAY RF WAVEFORM (EYE-PATTERN) 2. DISC DETECTION
CD(TCD784) PLAY CD(TCD784) DETECTION
wRFO 1V/div
eFEI 500mV/div
rFOO 1V/div
qRFEQO
tTEI 1V/div
yTRO 1V/div
uFMO 500mV/div
iDMO 1V/div
3. TOC READ 4. FOCUS ADJUSTMENT

CD(TCD784) READ CD(TCD784) FOCUS ADJUSTMENT
wRFO 1V/div
1.2 CD-R (TCDR082W) PLAY 2.2 CD-R (TCDR082W) DETECTION
eFEI 500mV/div
rFOO 1V/div
wRFO 1V/div
eFEI
1V/div 500mV/div
tTEI
rFOO 1V/div
yTRO 1V/div
RFEQO
qu FMO 500mV/div
tTEI 1V/div
iDMO 1V/div
yTRO 1V/div
uFMO 500mV/div
iDMO 1V/div
3.2 CD-R (TCDR082W) READ 4.2 CD-R (TCDR082W) FOCUS ADJUSTMENT
1.3 CD-RW (TCDW082W) PLAY 2.3 CD-RW (TCDW082W) DETECTION

wRFO 1V/div
eFEI 500mV/div
46
wRFO 1V/div
rFOO 1V/div
eFEI 500mV/div
4. CD Playback
Q3LRCK
Q4SCLK
Q5SDATA
STANDARD GND
(B)
5. LOADER OPEN-CLOSE
oOPSW
Q0FCLSW
Q2LOAD-
Q1LOAD+
OPEN CLOSE
STANDARD GND
(C)
47
BLOCK DIAGRAM
AUDIO(DIGTAL) SIGNAL
M-CR611/511 BLOCK DIAGRAM AUDIO(ANALOG) SIGNAL

MICOM CONTROL
NFC ANT PCB

BACKLIGHT PCB FRONT PCB BACKLIGHT PCB SMPS PCB
R R
LED PWM DRIVER POWER LED
G OLED G
TLC59108
S020-MXS4035A
D0 EL_DC
B I2C(DATA,CLK) D1 EL_RW
D2 EL_RST LED_RED KEY1 B
RST D3
EL_CS
LED_GREEN KEY2
D4 LED_OR KEY3
MCR611 ONLY
REMOTE
FRONT USB PCB W D5
D6 W
NFC_INT
D7
USB D+/-
POWER_DOWN
BI_AMP FOR CHINA FONT NJM8068
POWER_H CHINA ONLY DSDL/R/CLK L
OC_FLAG1 E_RXDMOEI SPI_REQ I2C
MCLK(DSD/I2S) STA309A
BD11600NUX
IOS E_TXDMIEO FACT_RST I2S(DSD->PCM)
PREOUT
OC_FLAG2
WPS SPI_CS
U_PWR1 SPI_CLK I2S
U_PWR2 SPI_MIEO MUTE
FUSB_SW SPI_MOEI R5F56108VNFP GD25Q32B
IOS RUSB_SW E_RST
USB_OE I2C
R
WPS CY920 R1EX24128BSA
FLASH
D+/-
SUBWOOFER
CLK/DATA/RST/PDN PREOUT_MUTE
CHARGE MODE
NJM8068
REAR D+/- PCM9211

USB 12MHZ
24M576(10P)
X101
D+/-
MUTE
MFI
X100
SW_MUTE
BD11600NUX TAS5558 NJM4556
I2S
HEADPHONE
TD+/-,RD+/-
LAN A/D
MUTE
DSD BCK
2.8224MHZ 11.2896MHZ
WIFI ANT I2S/DSD DSDL/R/CLK
ICS511(X4)
CY920_I2S CLK/DATA/RST/MUTE/HP/PDN/MUTE H/P_MUTE
OPT2_SPDIF
BT ANT OPT1_SPDIF
L
DAB_SPDIF
SPK OUT
CD_SPDIF
NETWORK PCB
CD_PCB AMP PCB R
CD_SDRAMSTB CD_SPDIF SD/OTW
BUS3
TU_CLK/DATA//CE/RST/INT/ BUS2
BUS1
BUS0 CD_DSP TAS5142 BTL LPF
NJM2752RB2
CD_CCE
SELECTOR
INPUT_SEL
CD_BUCK
CD_OPSW
TC94A92FG
INPUT
CD_CLSW
CD_INSW
CD_DECRST BTL
TUNER CD_DREQ
CD_SBSY
LPF
OPT2_SPDIF
EXCEPT EU
OPT1_SPDIF
CD_M_STBY
DAB_SPDIF
CD_OPEN
CD_CLOSE
L
CD_LDCHK
OPT2 SD/OTW
SPK OUT
(BIAMP)
MCR611 ONLY
MOTOR DRIVER TAS5142 BTL
LPF
OPT1 IP4001CR
BTL
ANALOG INPUT PCB CL_SW LMSW R
OP_SW SLED+/-
LPF
LOADING+ SPINDLE+/-
DAB INPUT PCB TR+/-
FC+/-
ONLY EU PD
A/B/C/D/E/F
MCR611 ONLY
VERONA2
DAB
CD_MECHA
DAB_RX
DAB_TX
DAB_VCC_PWR
MCR611 ONLY
48
POWER DIAGRAM
+29V 5.6A
+29V OR +19V(BI-AMP) BIAMP(+19V) TAS5142
DIGITAL AMP
0.196A
+12V_D +12V_D TAS5142
+12V DIGITAL AMP
0.5A
TPS54340 +8V
CONTROLLLER LM7808 IP4001CR
MOTOR DRIVER IC
M-CR611 ONLY
HGND
0.02A
A_5V NJM2752
AUDIO_SELECTOR
0.035A
TU_+5V
TUNER
0.06A
+12V A1281 KIA7812 LM7805 DIR_+5V PCM9211
S/W TR +12V_LDO DIR/ADC
+5V_LDO
0.06A
A_+12V NJM8068/NJM4556
OPAMP
AGND
CONTROLLLER
0.06A
-12V C3209 KIA79L12 A_-12V
NKM2068/NJM4556
S/W TR -12V_LDO OPAMP
+20V NJM2387 0.06A OLED_16V S020-MXS4035A

16V_LDO OLED
SWITCH
M3V3 R5F56108VNFP
MICOM
M3V3 BD4730
RESET_IC
+5V ST_BY_0.3W (TAGET_0.2W) +5V AZ1117_3V3 0.7A M3V3 R1EX24128BSAS0I
+3V3_LDO EEPROM
M3V3 GD25Q32B M-CR611 CHINA
FLASH MEMORY ONLY
FET FET M3V3 S020-MXS4035A
SWITCH TR SWITCH OLED_3V3
SWITCH
TLC59108
PWM_CONTROL M-CR611 ONLY
NETWORK_ST_BY_4W (TAGET_3W)
+5V AZ1117_3V3 0.7A DIR_3V3 PCM9211

+3V3_LDO DIR
DIR_3V3
DGND OPTICAL
+3V3
DIR_3V3
STA309 M-CR611 ONLY
DSD TO PCM
DIR_3V3
M-CR611 ONLY TAS5508
PWM PROCESSOR
+5V AZ1117_3V3 0.7A
+3V3_LDO CD_3V3 CD_MECHA
PICK_UP M-CR611 ONLY
CD_3V3
TC94A92FG M-CR611 ONLY
CD DSP
1117_1V5 CD_1V5
DAB ONLY TC94A92FG M-CR611 ONLY
+1V5_LDO CD DSP
+5V AP7361_3V3 0.3A
+3V3_LDO DAB3V3 VERONA2 M-CR611 EU
DAB ONLY
NET_3V3 BD11600NUX X2
USB_SW
NET_3V3 MX25L25635FMI-10G
MCR511/611 POWER_DIAGRAM
+5V EN5339QI 0.52A FLASH
DC/DC 3.3
SWITCH NET_3V3 MFI337S3959
MFI CHIP
NET_3V3
CY920_3V3
+5V EN5339QI 0.2A NET_2V5
DC/DC 2.5 CY920_2V5
SWITCH
+5V EN5339QI 0.3A NET_1V8

DC/DC 1.8 CY920_1V8
SWITCH
+5V EN5339QI
DC/DC 1.2 0.4A NET_1V2
CY920_1V2
SWITCH
+5V BD82065FVJ
VBUS5V
VBUS_SW FRONT_USB 5V(1A)
1A
VBUS5V
+5V BD82065FVJ REAR_USB 5V(1A)
1A VBUS_SW
49
WIRING DIAGRAM
AC INLET
MCR511/611 WIRE BLOCK
INPUT / CNT
(MCR611 / MCR511)
OPTICAL AMP
6P WAFER
6P WIRE
DAB
5P BD TO BD
5P BD TO BD
6P BD`TO BD (MCR511) 6P BD`TO BD (MCR511)
(ONLY 611 EU) 10P BD`TO BD (MCR611) 10P BD`TO BD (MCR611)
11P B`D TO B`D
11P B`D TO B`D
16P BD`TO BD
MCR611 ONLY
MCR611 ONLY
Verona2
26P B`D TO B`D
5P BD TO BD (MCR511) MAIN
26P B`D TO B`D 23P BD TO BD (MCR611)
TRANS
5P WIRE 6P BD`TO BD (MCR511) 6P BD`TO BD (MCR511)

[OPTICAL/WPS] 10P BD`TO BD (MCR611) 10P BD`TO BD (MCR611)
(OPTICAL2 ONLY 611)
(IOS ONLY 511)
16P BD`TO BD
NETWORK 5P BD TO BD (MCR511)
23P BD TO BD (MCR611)
11P WAFER
11P WIRE
MAIN SMPS
3P WAFER
21P CARD 5P WIRE
6P WAFER
6P WIRE
CY920
MECHA
16P FFC
64P B`D TO B`D
64P B`D TO B`D

64P B`D TO B`D
64P B`D TO B`D
27P BD TO BD
27P BD TO BD
21P CARD 5P WAFER 16P FFC
CD SUB
5P WIRE
MCR611 ONLY
TRANS
29P FFC (MCR511)
33P FFC (MCR611)
H/P
29P FFC (MCR511) 5P WAFER 6PWAFER
3P WIRE
33P FFC (MCR611)
CONNECTOR
B`D
29P FFC (MCR511) 5P WAFER 3P WAFER 4P WAFER
33P FFC (MCR611)
6PWAFER
29P FFC (MCR511)

33P FFC (MCR611) FRONT 3P WIRE
5P WAFER
2P WIRE
LED L OLED MODULE LED R

FRONT USB MCR611 ONLY MCR611 ONLY
NFC
3P WAFER
4P WAFER
4P WIRE
3P WIRE
30P FFC
KEY L KEY R
MCR611 ONLY MCR611 ONLY
5P PATTERN 5P PATTERN
50
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
PRINTED CIRCUIT BOARDS

Lead-free Solder
A When soldering, use the Lead-free Solder (Sn-Ag-Cu). A
鉛フリー半田
半田付けには、鉛フリー半田 (Sn-Ag-Cu) を使用してください。
MAIN (A SIDE) MAIN (B SIDE)
B B
RED BLACK BLACK RED

WHITE RED BLACK
C C
C130 R109
611 611
511 511
R115 C117
C109
C120
C121 C116
C122
C115
C111
C128
R110
C160
R418
R420
R419
R165
R471
C149
R179
C148
R472
R164
C114
C127
C129 R114
R150
C146
L105
JACK105 C110 Q122 Q113 Q114
C168
R178
R183
R142 R151
L102 L101
R204
R111
C147
R113
JACK104
R127 R152
R125 C136
R124 C135
C125 R126 R149
C123
R221
R121 JACK102
GND
R112
C108
GND
R490 R134 R487 C137 PF101
LB+
LA+
RB+
RA+
PF102
R219
LB-
LA-
RB-
RA-
FPC101 10P C139 C131 R493 10P C119
R141
R491 R133 R135
C103 C105
R240
R238
C358
C357
FPC103 R489R106R104 C167
2.CPU_+3V3
R477R476 R108
D R407 C112C104R492 R520 IC101 Q124 Q106 Q107
D
R182
R177
R384
R382
R380
L127 IC102
7.DSP BOOT
C161
C174
C175
NJM8068
C126
R488R105R486
C124
1.RESET
9.TRST#
R410 STA309A
5.MGND
L122
2.CPU_+3V3
R519
8.EMLE
10.TDO
R101
11.TMS
C143 C153
6.CNVSS
7.MD1
6.MD0
4.TCK
R409
5.MGND
3.TDI
R421
8
C152 R518 C166
1.RESET
50
R514 R589
C118
R422
R
C145 R513
4.RXD
3.TXD
R536
R515
R516
L119 R517
C199
C198
R423
R502
C217
L120
C173
C170
C280
R373
R372
C134
R416
C355
R415
D120 R176 R510 R590

R594
C138 BKT805 C101 C163 C169
C356
R272
C257R345
R344R430
R190R200
R501 R323 C133 L106 R189
C308 C162 R188
R322 C348
R342 C307R387
C259
R343
D115
IC117 R592R593
R547
R548
C144
R273
R271
R270
R1EX24128BSAS0I
L118 R470 R187
R546
R545
R544
BD4730 IC113
R339 R381C314
X102 R469 R552

R186
R 5 37
R427
R359
R346
R385
C283
R386
AZ1117CH-3.3 R468 R132 R591
C347
L107
R242 53 33
C349
R 5
C155
R614
R249 2
R426
C315
GD25Q32B
R143
R511
R366
BKT804
C346
2
R341
R425
R144
C140
52
IC109
R528
R503 R529
R464 R531
R199 R530
R527
R524
R252
R256
R478
R218
R
IC106
L109
C132
C141
Q128 C262
L108
C219
R244
C238 R185 Q127 C102
R375 R483
R523
MCR611 23P
R428 R475R474 L114

C237 R195 R326R328 R463
C158
C345
C154
C263
C266
C264
C267
R315 R146
R160
R157
R465
R466
R467
R473
R400
R396
R243
C203
R223
R482
C222
R261
C197
R504 C258 D122 IC107 R319R321
E R192 R461
E
Q132 Q129
R277
D117
C248 R417 C274R535
C235
C244
R312
C276 R276 PCM9211

24.576MHz
C249 C272 R325 C320 C319

R424 R364
R534
R336C242
R388
C255 C187 C192 R275 C207 R462
C275
C271 C214 C224
C225
C220 R338 R237
R374
R370
R379
R378
R367
R365
R363
R361
R331
R291R292 R460
C231
R318
C229
R309 R340
Q111
R303R316R314 C279 R304
Q110
R220 R225 R459
R302
R317 R305R306
R505
C226
X101
C282
C291
C292
C293
23.R_OUT R227
R347
R349
R351
R353
R355
R357
R295 R307 R301 22.AGND R399 C285 C321 C228C227 R228

R298 R308 C260
R255
R299
Q112 Q115
21.L_OUT
C236
ICS511
C288 R229
IC103
R300 R293 R297 R313
R360 R334
R337
R335
R393
R394
R615
R390
R376
Q116
L125
R429 20.AGND C265 R230 R296 R311

19.AIN_CONT C269 C289 R285R286
C213
C205
R232
R231
R506 18.A_+5V C212 C273 C295 R278 R283
C221
C202
17.A_+5V R405 C211 R484 R266R263

C206R310
C215 R166
C223
R452 R171 R404 R403 C298
Q117
16.DGND
R222
R324
R320
C186 R294 R260R258
R348
R213 R350
R198 R352
R435 R354
R356
R358
R333
R451 C216 R432 15.TU_INT/DO R406 IC105 C239 C316 R253
R184
C181 C204 NJM8068 C240 Q126 C317
C251
R284
R481
R485
14.TU_RST
C253
R431 R247
R161
R158
R453
IC111
R391
C208
L117
R250 13.TU_CE L124

R269
R274
R454
R455
R254
R401 R145 R389 C184
R330
R332
R194
C278
C277
C281
R450 12.TU_SDA/DI
R201
L129
C254
R233
R234
R257
R259
R262
R479
R480
R235
R500
R449 R398 C179
R172
C164
R448 11.TU_CLK
C252
C142
R447 R241 10.TU/DAB_ON R408 C243 R329 D108 C210 L128 R239
R155 C209
C299
R446 R205 23.R_OUT
Q123 R433
C180
R613
R445 C171 C230 22.AGND IC112
D111 C201 C159C157
L115
L116
R440 C193 R369 C200 R5F56108VNFP
C177
C178
L104 R181C156 21.L_OUT

Q125
R441 C185 20.AGND

D106
C194
R236
R224
R442 R212 R402 C150 R512 19.AIN_CONT
C310 R202
C234 R196Q104 R117Q101 R102
Q121
L103
D102R116 R107
R412
R413
R414
R443
C324
R397
C190
MCR511 5P
18.A_+5V
F R444 R395 R139 R119 C106 Q103 IC108
F
R226
17.A_+5V
R208 C165
C241
Q118 C322 R128 D101

R174
TAS5558DCAR C232 16.DGND
R434
R193
R170
R173
R180
R175
D103 C303
C309
15.TU_INT/DO
C311
R122R131
R130R123
R136
D110 D109 IC110 C294 C233
R509 PF103 D121 IC104 14.TU_RST
R217R216
R215R214
R437R436
R209R210
R438R207
R206
LM7805
R191
16P NJM4556AM D113 13.TU_CE

12.TU_SDA/DI
9.ST_+5V 11.TU_CLK
11.+18V_OLED
R211
R507
8.ST_+5V 10.TU/DAB_ON C176
12.NFC_ACK
3.POWER_H
C172
9.STBY_+5V
R169 7.DGND CP106 9.ST_+5V
1.P_DOWN
C245
6.SPDIF 23P 8.ST_+5V
2.BI_AMP
8.D_+12V
4.A_+12V
10.DGND
Q119 D107D105 D112
6.A_-12V
Q109 7.DGND
7.DGND
5.WPS_ON
5.AGND
R439
RING,TER WIRE
4.OPT2 C256 L126 GND101 6.SPDIF

3.OPT1 C246 C188 5.WPS_ON
R140Q105 R118
R103
C107
R203
2.AGND
2.DGND R129Q102 R521 4.OPT2
3.HP_L
1.USB_OE
1.HP_R
1.D_+3V3 R197 R120 3.OPT1
R290
R289
R288
R287
2.FET_5V_ON
L113
L112
L110
L111
R525 2.DGND
MTG
3.FET_2V2_ON
Pb R526 1.D_+3V3 4.DC/DC_1V8_ON

R559 R558 R282R281 R280 R279 5.DC/DC_2V5_ON
R578
R577
R246R268 R248R267 6.DC/DC_3V3_ON
R162
R159
R156
R138
R148
R154
R245R265 R251R264 7.IOS(WIFI)
C189C196 C191C195
R496
R497
C353
CP102 8.U_PWR2
R576
27P 9.U_PWR1
R553
R554
10.REAR_USB_SW(OE2)
G CP103
G
C302
C306
C313
C312
C301
C305
R392 11.FRONT_USB_SW(OE1)
2.AGND
CP101
1.HP_R
3.HP_L
C151 1.USB_OE 12P R327 12.OC_FLAG1
R541
R542
R543
C318 13.OC_FLAG2
R153
R147
R137
R163
2.FET_5V_ON
Q134
C182 C183
R539
R538
R540
3P
R167 3.FET_2V2_ON C341 14.E_RST
15.SPI_MOEI
Q136
4.DC/DC_1V8_ON C340 D114 16.SPI_MIEO
Q120
5.DC/DC_2V5_ON
11.+18V_OLED
6.DC/DC_3V3_ON C342 17.SPI_CLK

18.SPI_CS
12.NFC_ACK
R555
R556
R557
IN ICT OP ADJ FI
3.POWER_H
7.IOS(WIFI)
9.STBY_+5V
Q130 R498 19.FACT_RST

1.P_DOWN
8.U_PWR2 C352 20.SPI_REQ

2.BI_AMP
8.D_+12V
4.A_+12V
10.DGND
9.U_PWR1
6.A_-12V
4.D_+12V
D104
C350
Q135
C351
7.DGND
21.CY920_DATA/DSDL
5.AGND
R168 R494
2.D_+5V
10.REAR_USB_SW(OE2) C337
C339
C338
5.DGND
3.DGND
1.DGND
11.FRONT_USB_SW(OE1) 22.CY920_DSDR
2D_+12V
4.D_+5V
D118
1.DGND
3.DGND
5.DGND
12.OC_FLAG1 CP104 Q137 23.CY920_BCK/DSD_BCK
L121
R495
C354
R499
13.OC_FLAG2 Q108 24.CY920LRCK
25.CY920_MCLK
0
14.E_RST
56
15.SPI_MOEI 26.MGND 1.CD_LDCHK

R
C261 16.SPI_MIEO 27.MGND 2.CD_CLOSE

17.SPI_CLK 3.CD_OPEN
18.SPI_CS 4.CD_MSTBY
5.CD_SBSY
1
19.FACT_RST
FPC106
56
20.SPI_REQ 6.CD_DREQ
D119
R
21.CY920_DATA/DSDL 7.CD_DECRST
FPC102 22.CY920_DSDR 8.CD_INSW
H 21P 23.CY920_BCK/DSD_BCK
24.CY920LRCK
9.CD_CLSW
10.CD_CPSW H
25.CY920_MCLK 11.CD_BUCK
MCR511:30P MCR611:34P
C287
1.CD_LDCHK 26.MGND 12.CD_CCE

2.CD_CLOSE C268 27.MGND 13.BUS0
3.CD_OPEN 14.MGND
4.CD_MSTBY 15.BUS1
5.CD_SBSY 16.BUS2
6.CD_DREQ 17.BUS3
7.CD_DECRST C286 18.CD_SRAMSTB
D116
8.CD_INSW 19.MGND
9.CD_CLSW 20.SPDIF
10.CD_CPSW 21.MGND 1.CPU_+3V3
11.CD_BUCK R411 2.TXT_232
12.CD_CCE 3.RXD_232
13.BUS0 IC116 33.LED_+5V 34.NC
31.LED_RST 32.LED_+5V 4.MGND
14.MGND AZ1117CH-3.3
15.BUS1 C326 29.I2S_SCL 30.I2S_SDA
16.BUS2 R563R562 C325 27.EL_CS 28.DGND
17.BUS3 25.EL_RW 26.EL_RST
18.CD_SRAMSTB C323 23.D0 24.EL_DC
19.MGND C327 21.D2 22.DGND
20.SPDIF 19.D4 20.EL_RD
21.MGND 17.D6 18.D1
J 34.NC
32.LED_+5V
33.LED_+5V
31.LED_RST
C328
C329
15.DGND
13.D7
16.D3
14.D5 J
30.I2S_SDA 29.I2S_SCL 11.KEY1 12.OLED_+16V
28.DGND 27.EL_CS C330 9.KEY2 10.OLED_+16V
26.EL_RST 25.EL_RW C331 7.LED_OR 8.OLED_+3V3
24.EL_DC 23.D0 5.HP_DET 6.REMOTE
22.DGND 21.D2 C332 3.LED_GREEN4.CPU_+3V3
20.EL_RD 19.D4 1.LED_RED 2.KEY3
C247 18.D1 17.D6
R383
R566
R567
R564R565 16.D3 15.DGND

14.D5 13.D7 C304
Q131
12.OLED_+16V 11.KEY1 C300
10.OLED_+16V 9.KEY2 C336
R362
R377 8.OLED_+3V3 7.LED_OR C343 C296

6.REMOTE 5.HP_DET C344 R368
C250
R371 4.CPU_+3V3 3.LED_GREEN

2.KEY3 1.LED_RED
C335
C334
C333
Q133
R456 FPC104
K C284 K
CLP101
R457
R458
IC114
Pb NJM2387ADL3 C270
C297
C290
L123
L L
M M
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
51
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
AMP (A SIDE) AMP (B SIDE) CNT (A SIDE)
B B
C522 PF101_A R581
ADGND
PF102_A
R578
LB+LB+
LA+LA+
LB- LB-
LA- LA-
R580
R576
ADGND
CP6
C579
C521
C585
L513 C528 R560
L510 C572
L502 C534
R557 R559 611 OPTION
ADGND
ADGND
R555
C529 C583 C573
MCR511(30P)/MCR611(34P)
+29V
+29V
30.NC / I2C_SDA
+29V
+29V
29.NC / I2C_SCL
C519
C532 C570
3.LED_GREEN
25.EL_RW,WR
C580
32.LED_RST
C533
1.LED_RED
4.3V3_CPU
FPC4
26.EL_RST
6.REMOTE
31.LED_5V
33.LED_5V
5.H/P_DET
24.EL_D/C
7.LED_OR
20.EL_RD
27.EL_CS
8.3V3_D1
15.DGND
22.DGND
28.DGND
C518
C C569 C584
C
11.KEY1
C517 C548
2.KEY3
9.KEY2
ADGND
ADGND
10.16V
12.16V
+29V
+29V
+29V
+29V
C597
34.NC
13.D7
14.D5
16.D3
17.D6
18.D1
19.D4
21.D2
23.D0
C568
ADGND
C549 FPC4
CP6
PF101_A
R589 L505 C550
RB+RB+
RA+RA+
RB-RB-
RA-RA-
MCR511(29P) / MCR611(33P)
Pb 1.LED_RED 18.D1
ADGND
2.KEY3 19.D4
C508
C560
C561
C509
C504 C505
C598 C547
C556 C557
3.LED_GREEN20.EL_RD
CN500 4.3V3_CPU 21.D2
5.H/P_DET 22.DGND
IN
C511 C506 C555 C558 6.REMOTE 23.D0
7.LED_OR 24.EL_D/C
Pb
C554 L504 8.3V3_D1 25.EL_RW,WR
ICT
C507
C503
3300/50 9.KEY2
C510
C559
26.EL_RST
C562
3300/50
10.16V
C5005
27.EL_CS
C5001
C515
C566 C586 C535 11.KEY1 28.DGND
12.16V 29.NC / I2C_SCL
OP ADJ
R562
13.D7
C5007
C5006
C5003
C5002
30.I2C_SDA
C5008
R554
R583
D 14.D5 D
C5004
R575
32.LED_5V 611 OPTION
C544
15.DGND
C553
C571 C581 C520 C530

16.D3 32.LED_RST IN ICT OP ADJ FI
C536 33.LED_5V
C513
17.D6
C514
C565
C595
C589
C538
C577
C524
C526
C575
L512
R551
MCR511/611_CNT(MP)
L511 L503 C587 C567
C516
R567
C592
R588
C564
C541
7020-07849-000-0S
FI
C531
TAS5142DKDR
TAS5142DKDR
L507
R558 R582
L515
C523
C574
C582
C502
L501
R572
C512
R561 R579
IC500
IC502
L500
C591
R571
R566
C593
PWM_P1C501
C563
C594
C540
L514
C552
C527
R556
R553
C525
L509
PWM_M8
PWM_M7
PWM_M2
PWM_M1
PWM_P8
PWM_P7
PWM_P2
C578
C576
R577
R574
L508 100/16 L506 C543
R550
C551 R587
C542
E 100/16 E
R573
Q502 Q500
C590
PF103_A
C596
R564 R563
R585 R584
CNT (B SIDE)
R552
100/16
C500
100/16
100/16
SP_MCH
SP_PCH
R565
C537
ADGND
C545
C539
C588
R586
RESET
Q501
OTW
+12V
+29V
Q503
SD
R570
R569
F F
INPUT (A SIDE) INPUT (B SIDE) J1
C81 C91
MCR511(30P)/MCR611(34P) C77 C68
C74 C64
34.NC
33.LED_5V
32.LED_RST
31.LED_5V
30.NC / I2C_SDA
29.NC / I2C_SCL
28.DGND
27.EL_CS
26.EL_RST
25.EL_RW,WR
24.EL_D/C
23.D0
22.DGND
21.D2
20.EL_RD
19.D4
18.D1
17.D6
16.D3
15.DGND
14.D5
13.D7
12.16V
11.KEY1
10.16V
9.KEY2
8.3V3_D1
7.LED_OR
6.REMOTE
5.H/P_DET
4.3V3_CPU
3.LED_GREEN
2.KEY3
1.LED_RED
CP6
15.TU_INT/DO CP1(21P_MALE) C61
CP1(21P_MALE) MCR611 INPUT B`D (MP) 16.GND 1.3V3
FPC4
C76
1.3V3 17.A+5V 2.GND MCR511(29P) / MCR611(33P)
18.A+5V 18.D1 C73
2.GND 3.OPT_OUT1 1.LED_RED
3.OPT_OUT1 19.AIN_CON 4.OPT_OUT2 19.D4 2.KEY3 C72
4.OPT_OUT2
5.WPS
7020-07845-000-0S 20.GND
21.L_OUT 5.WPS 20.EL_RD
21.D2
3.LED_GREEN
4.3V3_CPU
C92
C86
-
6.SPDIF
G 6.SPDIF
7.GND
22.GND
23.R_OUT 7.GND 22.DGND
23.D0
5.H/P_DET C84 G
8.D+5V 6.REMOTE C83
8.D+5V 9.D+5V 611 OPTION 24.EL_D/C 7.LED_OR
9.D+5V 10.DAB_ON 25.EL_RW,WR 8.3V3_D1 C93
10.DAB_ON
11.TU_CLK
11.TU_CLK MCR511/611 CNT B`D (MP) 26.EL_RST
27.EL_CS
9.KEY2
BURRING 10.16V J2
12.TU_SDA/DI
12.TU_SDA/DI
7020-07849-000-0S 28.DGND
C88
13.TU_CE 11.KEY1
13.TU_CE 14.TU_RST 29.NC / I2C_SCL12.16V
J12
14.TU_RST 30.I2C_SDA 13.D7
C85
C87
BKT1 J25
15.TU_INT/DO L8 32.LED_5V 14.D5
16.GND 32.LED_RST 15.DGND
C78
J13
J14
J15
J16
Pb
17.A+5V CP2(11P_MALE) 33.LED_5V 16.D3
CP2
18.A+5V CP2(11P_MALE) 1.SPDIF 17.D6
C58
C59
C60
19.AIN_CON 1.SPDIF 2.GND
C79
20.GND 2.GND 3.D+5V
J20
3.D+5V CUSHION
21.L_OUT J11 4.D+5V 611 OPTION
22.GND 4.D+5V 5.DAB_ON
C67
C69
C70
23.R_OUT 5.DAB_ON 6.GND
CP1
H 6.GND 7.DAB_OUT H
J26
J27
C66 7.DAB_OUT 8.DAB_IN
J2
8.DAB_IN 9.DAB_L J17 L7
R54
R55
3
9.DAB_L 10.GND
J10 10.GND 11.DAB_R
C63
J2
11.DAB_R
4
J21
NJM2752RB2
J9 R56
C80
J8
J22
FI
7020-07845-000-0S
MCR611 INPUT B`D (MP)
C62
IC2
J7
L6
C71
J6
OP ADJ
J5 J4
C94 C95
C65
R53
CP3(5P_MALE)
J 5.3V3
5.3V3
4.GND
J
J19
J18
4.GND 3.OPT_OUT1
ICT
3.OPT_OUT1 L_OUT 2.GND

2.GND R61 1.OPT_OUT2
R_OUT
R65
R69
C75 C82 1.OPT_OUT2 C90 C89

NFC (B SIDE)
A+5V
CP3(5P_MALE) SCLK
R60
R68 R67
NFC (A SIDE)
IN
C101
SDA R72 R71

CP3
R59
SEN
RST L_OUT R58
JK2
INT R_OUT
R73
TM1(TUNER) A+5V R57

SCLK
TM1
SDA
SW15 SEN
CN910
RST
INT 7020-07846-000-0S
TUNER
K GND(BK) K
FD(WHT)
Pb
C958
7020-07846-000-0S
R958
NFC-NTAG203F-00
NTAG203F
IN ICT OP ADJ FI
IC901
C956
L L
M M
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
52
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
FRONT (A SIDE) KEY L (A SIDE) KEY L (B SIDE)
B LED_L LED_R IN ICT OP ADJ FI B
30.16V_OLED
GND4 GND12
15.EL_RW,WR
25.VDDIO
2.16V_OLED
13.D0_SCLK
12.D1_SDIN
29.VLSS
MCR611 KEY_L B`D (MP)
23.IREF
20.EL_RST
26.VDD
FPC2(30P)
18.EL_D/C
28.VSL
C33
27.VCI
14.EL_RD
19.EL_CS
3.VCCMH
24.NC
21.DGND
D3 22.CL
1.DGND
C51 C37
7020-07845-000-0S
4.VLSS
16.BS0
17.BS1
5.CLS
10.D3
11.D2
C40 C44
6.D7
7.D6
8.D5
9.D4
MCR611 FRONT B`D (MP) C55
C52
R G
7020-07842-000-0S
C47
C46
IN ICT OP ADJ FI
R50
C38
R51
C27
R44
C28
C26
C32
R46
R47
R48
C45
R49
C49
C48
LED1 CURSOR UP
C36 SW3
C43
R13
C6
25.EL_RW,WR
C5 RC1
MCR611 KEY_L B`D (MP)
32.LED_RST
R10 R8
30.I2C_SDA
29.I2C_SCL
26.EL_RST
R9
31.LED_5V
33.LED_5V
R52
FPC1(33P)
24.EL_D/C
R12 R5
27.EL_CS
22.DGND
28.DGND
C
R7 R11 C20 CURSOR LEFT 7020-07845-000-0SCURSOR RIGHT C
Pb
R6 R19
23.D0
C41 R20
R15
Q4 Q1 R4
Q2 Q3 CN2(4P_WIRE) C18
FPC2 4.KEY1_2 J3
CN2
CN3(3P_WIRE) 3.DGND R14
R33 2.KEY3 L2 SW5 SW6
R45
1.KEY2
C31
2.KEY3 1.KEY2
C3 C14
R42
R40
R38
R34
CN3 3.DGND CN1(3P_WIRE)
C2 C11 3.H/P_L ENTER
L4 C39 C10 C24
C1 C8 2.AGND SW10
C22
C12
C30
C29
C50
R35
R39
R41
R43
1.H/P_R
C9
C7
L3
C17
C19
C16
C13
D2
D1
L5 C56 IC1 JK1
TLC59108 CN1
C34
SW4
D R32 R28 CURSOR DOWN
D
C57
3.LED_GREEN
FPC1 R31 R29
Pb
R1
R2
R3
R30 C23
1.LED_RED
4.3V3_CPU
C35
6.REMOTE
5.H/P_DET
FPC1(33P)
7.LED_OR
R27
C54
C43
C36
20.EL_RD
8.3V3_D1
15.DGND
C42
11.KEY1
R26
C4
2.KEY3
9.KEY2
R37
10.16V
12.16V
C53
13.D7
14.D5
16.D3
17.D6
18.D1
19.D4
21.D2
SW1 C25
R36 L1
R21
C15
CP5
INPUT
SW9 3.DGND
C21
CP5(3P)
2.KEY3
E FRONT (B SIDE) 1.KEY2
E
1.KEY2
2.KEY3
CP5(3P)
3.DGND
30.16V_OLED
29.VLSS
28.VSL
27.VCI
26.VDD
25.VDDIO
24.NC
23.IREF
22.CL
21.DGND
20.EL_RST
19.EL_CS
18.EL_D/C
17.BS1
16.BS0
15.EL_RW,WR
14.EL_RD
13.D0_SCLK
12.D1_SDIN
11.D2
10.D3
9.D4
8.D5
7.D6
6.D7
5.CLS
4.VLSS
3.VCCMH
2.16V_OLED
1.DGND
FPC2(30P)
F G
R F
KEY R (A SIDE) KEY R (B SIDE)
CN2(4P_WIRE)
4.KEY1_2
3.DGND
2.KEY3 32.LED_RST
33.LED_5V
31.LED_5V
30.I2C_SDA
29.I2C_SCL
28.DGND
27.EL_CS
26.EL_RST
25.EL_RW,WR
24.EL_D/C
23.D0
22.DGND
21.D2
20.EL_RD
19.D4
18.D1
17.D6
16.D3
15.DGND
14.D5
13.D7
12.16V
11.KEY1
10.16V
9.KEY2
8.3V3_D1
7.LED_OR
6.REMOTE
5.H/P_DET
4.3V3_CPU
3.LED_GREEN
2.KEY3
1.LED_RED
FPC1(33P)
1.KEY2
IN ICT OP ADJ FI
G MCR611 FRONT B`D (MP) G
CN1(3P_WIRE)
7020-07842-000-0S
3.H/P_L
2.AGND OPEN/CLOSE
1.H/P_R SW2
CN3(3P_WIRE)
1.KEY2 MCR611 KEY_R B`D (MP) MCR611 KEY_R B`D (MP)
2.KEY3
3.DGND SKIP_REV 7020-07845-000-0S SKIP_FWD 7020-07845-000-0S
R25
H SW13 SW14
H
PLAY/PAUSE
SW8
R17
STOP
CP5(4P)
1.KEY1_2
SW12 2.DGND
R24 3.KEY3
4.KEY2
CP4
J
FRONT L (A SIDE) FRONT L (B SIDE) R23
J
VOL_UP Pb
C52
C41
C34
CP5(4P) R22
1.KEY1_2 SW11 R16
LED6 LED8
L 2.DGND
3.KEY3
4.KEY2
LED9 LED7
K K
VOL_DOWN
SW7
FRONT R (A SIDE) FRONT R (B SIDE)
L LED3 LED5 L
R
LED4 LED2
M M
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
53
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
B CD (A SIDE) NETWORK (A SIDE) NETWORK (B SIDE) B
7020-07844-000-0S FROM POWER
BKT802
M-CR611 MP [ CD ] 2015. 05. 13 CN703
HOLE
CLP4
Q701 C809 C706 IN ICT OP ADJ FI
GND_DRV
Pb
+12V_D
R706
C710
GND
D+5V
FO+
GND
GND
TR-
C703
RD
VC
C
A
E
A+3.3V
TR+
FO-
PD
LD
D
B
F
R701 C739
GND700 R703
R702
R705
R704
D701
R572
R573
R574
R575
C738
C705
C C
C950
C701
C702
C740
C755 L701 C742
R568
R569
R570
R571
C743 R795
L707 C741
C796
L705
L706 LOAD+
MCR511/611_NETWORK L824
EN5339QI C865
LOAD-
C868
C867
C866
R931
R848
R857
C864
D718
D717
OP_SW
L820
D716
R787 R790
C775
16 D715 GND_DRV
R715
C704
D711C765
R765 R763 R712 TO CD Pick-up CL_SW
R716 C719
IC806
C772 C769 C768 CN701 C861
TO DECK
C725 R717 C720
R588
CN705
C771 R764 R762 C773
R932 R850
R718 C721 C792
R786 C717 R711 R713
R846 R587 C857
C718 R852
R586R585
C876
C737
C794
R843
R788
CD_LDCHK C869 L821

CD_CLOSE L825
CLP3
EN5339QI
CN702R789
CD_OPEN
IC807
CD_M_MUTE C791 C793
C879
C878
C877
C734
MCR511/611_NETWORK
CD_SBSY
R849
R860
C875
C736
TO MAIN
C789
CD_DREQ R721 C767 C790
CD_DECRST
R743
C787
CD_LMSW C858
D C862 D
C798
CD_CLSW
TC94A92FG-301 C788 L823 R845 R853
R851
IC705
CD_OPSW R796 L827
LM7808
R847
C730
C833
AP1117-3.3
R722
IC704
C882 L805
IC701
C731
L807
X701
C766
TO DECK
GND_M
CN704
C779
CD_BUCK
C716
EN5339QI
GND_M
15P
CD_CCE
BUS0
R831
R839
C832
IC803
MCLK
C836
C835
C834
C786
R723
C727
GND
C763 IP4001CR R781
BUS1 IC702 27.GND_M LRCK
BUS2
C729 C762
L806
L809
BUS3
26.GND_M BCK
C728
R780
25.MCLK R897 C830 R828
C715
CD_SRAMSTB C761
24.LRCK DSDR C825
R900
C757
GND C783
23.BCK DATA R832 R835
SPDIF R829 R905
C760
R836
R840
C846
C817 22.DSDR
GND
C782
21.DATA SPI_REQ R906
C785
C750
D705 R799
C726 C744 C759 R775 20.SPI_REQ
R907
C816
C724 SP+
R779 19.F_RST F_RST
18.SPI_CS IC804EN5339QI
SP-
C758 C799 R774 SPI_CS
C847
R761 SLED+ 17.SPI_CLK
C754
C714 SLED- 16.SPI_MIEO SPI_CLK

C747 15.SPI_MOEI
C756
R798
14.E_RST SPI_MIEO
C839
C848
C849
C850
GND_DRV
AP1117-1.5
R749 C770 R797

13.OC_FLAG2
IC703
LMSW
12.OC_FLAG1 SPI_MOEI
E 11.FUSB_SW E_RST
E
R748
R750 C751 R714 10.RUSB_SW
9.PWR3 OC_FLAG2 L811
R778 8.PWR4 L814
C748 R771 7.WIFI OC_FLAG1 C831 R833 R841
R776 6.E_POWER1
5.E_POWER2
FUSB_SW R837 R842
C713 6.N_GND R834
R766
RUSB_SW R879
R738 R740 C746
4.E_POWER3
R733 R735 R745 5.N_GND 3.E_POWER4
C778
PWR3
16 2
C749
4.N_GND
R747
2.FET_5V
L8 81
R732 R734 R736 C774 C784
R746
3.NET_5V 1.USB_OE PWR4
L
R737 R739 R741 R794
2.NET_5V C829
R744 R955 R777 WIFI
J851
J850
1.NET_5V
C745
R838
R772 C795
E_POWER1
R930
C803
C764
IC802
R742
C781 E_POWER2 FDC608
R826
C826
C828
C712
C707
C708
C711
C777
E_POWER3
C780 BAR CODE LABEL C853 E_POWER4 R800
C818
C819
C797
IN ICT OP ADJ FI R782 FET_5VC805 C802

USBOE R803 R804
L800
R783
3.D+ C800
R784
CP813 L804 R605

CP805 R801 IC800 R827 L803
1.VBUS
6P C804 27P TPS2065CDBVR
L843
4.GND
CN807
R830
F L842 F
1.VBUS
2.D-
4.GND
C801
CY920 BKT800
3.D+
2.D-
R604
CN802 M3 BRACKET Q800
CD (B SIDE)
CN801
R600
C898R872 N_GND
R870
R869
R868
N_GND
R599
C894 N_GND
R874 NET_5V
L832
91 3
NET_5V
R867
R 91
1
BD11600NUX NET_5V
R
R915
R598
R601
IC810
L836
R912
R928
R910
R606
R923 IC809 L841 R927
BAR CODE LABEL R921 BD11600NUX
R864
C897 R863
R920
R919
R873R866
C901R865
C893
R918 R908 R902 R901
C914
C915
IC808
R871
BD82065FVJ R898
R893 R896
R602
GND
D+5V
GND_DA
+12V_D
GND_DA
R894
G R862 R899 G
R861
3
60
TR-
R917
R916
RD
R
R904
R903
C890 C887 IC812
E
R891
GND
FO+
C889 C886 MX25L25635FM

VC
R892 R889 R597 C888

A
M-CR611 MP [ CD ] 2015. 05. 13
R888 R607R608
R885 R875
R609 L830 R611
R596
R595
R876
A+3.3V
R890
C902
LOAD+
R612
D
R936
C900
C842
C841
C838
C837
C840
PD
FO-
LOAD-
B
TR+
R878
LD
OP_SW R877
FCO
GND_DRV
FMO
C844
L831
C851
CL_SW
C892
C891
C899
R935
C855
C854
C852
C856
C845 R584
R583
TRO
C859
H C860 R934 R933 H
R942C941
FEI
TEI
CD_LDCHK
Q801
CD_CLOSE
C920
VC
CD_OPEN
C909
C903
CD_M_MUTE CP811 C910
C885 R859 L822

C872 L826
R844
R
SP+ CD_SBSY
61
CD_DREQ
C873
CD_DECRST
R581 C871
R858
C896
C874
R582 C870
R549
R550
R551
SP- CD_LMSW IC805
MFI337S3959
SLED+ CD_CLSW
CD_OPSW
R937
C895
C881
C884
C880
C883
RFO
SLED- CD_BUCK
TPS2065CDBVR
CD_CCE R580R579
GND_DRV BUS0 C916
GND C917
LMSW BUS1 C930
RFEQO
C929 R929
L835
BUS2
C904
C928 L839
CD
EXT
IC811 L834
C927
C905R882
SRAMSTB
R926SW801
C933
R925 L840
GND
J SPDIF C931
C940 J
R895
GND
C939
INT C937
R924
R922
C938
C918
C919
L837
L838
C936
C907
C912
C911
C913
C935
R909
R914
C934
DMO
C908
C906
R886
L833
JACK800
GND
R855
R856
L828
D+
D-
BKT801 VBUS
BURING
R854
CP808 L829
C863
SW800
CP809
C922
C924
K C923
C932
K
L L
M M
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
54
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
SMPS (A SIDE) SMPS (B SIDE) DAB (A SIDE) DAB (B SIDE)

MCR611_DAB
B
Pb B
CP804
C823
C824
C812
R811
1.DAB_SPDIF R816 R818 R813 1.DAB_SPDIF
2.DGND 2.DGND
3.+5V 3.+5V
4.+5V R822
4.+5V
5.DAB_ON R821 5.DAB_ON

6.DGND
6.DGND 7.DAB_TX
7.DAB_TX 8.DAB_RX
C821
C822
C820
R815
R819
9.DAB_L
8.DAB_RX
L802
9.DAB_L C811 10.AGND
11.DAB_R
10.AGND
11.DAB_R
C819 IC801 R825
R824
R823
C C
C817
R817
BKT803
BURRING
C818
R820
C813
R814
C815
C814
C816
L801
R812
R810
C809
C810 C808
R809
R808
CP803
D D
C807
R807
E E
USB (A SIDE) USB (B SIDE)
F F
LUG800 LUG801
MCR511 MCR611
JK901
MCR611 C806
C843
MCR511/611_F_USB
G G
DLP11SN121SL2L
511MTG 611MTG
L810
1.VBUS
4.GND
1.VBUS
2.D-
3.D+
4.GND
3.D+
2.D-
Pb
CP800
H H
J J
OPTICAL (A SIDE) OPTICAL (B SIDE)
BKT901
K K
C953
C954
Pb
R938 C956
R939
JK810 C944
MCR611_OPTICAL
C943
C942
R941
2.DGND
4.DGND
R940
4.DGND
2.DGND
1.OPT2
3.OPT1
3.OPT1
1.OPT2
L L
5.3V3
C945
5.3V3
JK811
C957
CP812
M M
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
55
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A R546 100N R514 100N R543 - R526 -

CP101 A
M-CR511/611 MCU/PWM
R545 10N R513 10N R542 10N R525 10N C101 100N
2.AGND
1.HP_R
M-CR511 M-CR611 M-CR511 M-CR611
3.HP_L
CP101 R101 8K2
1 2 3
GND OPTION
JACK102 JACK104 R544 1000P R517 1000P R541 - R521 - HP_3P_WIRE R486
JACK101 JACK103 12K
4P(MCR611) 4P(MCR611) C103 C102 220/16
2P(MCR511) 2P(MCR511) M-CR611 ONLY
TO CN1
10
10
C357 10N R520 100N R540 - R547 10N R492 12K 68P
(Ref.NO : 100~)
C104
1
8K2
68P
C358 - R519 10N R538 10N R548 100N 1000P
3
3
5 6 7 8
5
1
3 2 3 2
NJM8068
R102
R103
D_+3V3
R534 0 R518 1000P R539 - C356 10N VCC
IC101
AGND
C105
C106 C107
R105
R106
R104
4K7
4K7
100P 100P
MGND
MGND
AGND
AGND
5R6-F 10N
AGND
AGND
AGND
C108 R108 C111 R107 10K Q101 Q102 C118
R109 C109 C110 R110 R111 220/16
10N 5R6-F 5R6-F 10N KTC2875B KTC2875B VSS
10N 5R6-F R396 100N R410 10N D101 1SS355T C112
R115 C117 1200P 4 3 2 1
R488
C114 R112 R113 C115 C116 R114
GND OPTION
D102 R116
3K6
47/25
10N 5R6-F
C125
5R6-F 10N 10N 5R6-F
R489
3K6
R117
R118
5R6-F R400 10N R407 1000P 1SS355T 22K C123 68P
47/25
10N C132
C126
C119 C120 C121
R119
R120
Q103 C124
47
47
220/10
20K
20K
A_+12V
B - - - C122 - R409 100N KRC102S C217 100N
B
R123
R487
C127 C128 C129
R469 0 STA309_LRCKI
STA309_BCKI
100N
8K2
STA309_PDN
STA309_DATA
NET01088
C131 R493
12K
- - R124 R125
R470 220
- - C130 R122 100K C134 1000P 12K
100N 4K7 4K7
AGND
MGND
AGND
BD121
BD121
R128
R129
L119
L120
MGND
10K
10K
R134
4K7
R131 1K R121
R552 10K
R614
R130
8K2
R133
C139
M-CR611 ONLY
68P
R126
R127
8K2
4K7
R414 100N R536 1000P
0
A_-12V C133 1200P C135 C136
100N
C346
R468 0
1SS355T D103
R132
1K
1K
KTC2875B
KTC2875B
100K 100N 100P 100P
_PF101 _PF102
Q104
R413 10N R515 10N
R136
100K
Q105
R510
R423
R491
0
R138
R490
3K6
C137
0
2 4 6 8 10 2 4 6 8 10
3K6
R135
-
R412 1000P R516 100N R137 10K -
KTC2875B
KTC2875B
MGND
1 3 5 7 9 1 3 5 7 9 R139 R140
2.2/50
ST+5V
PF101 PF102
2.2/50
C142
R143
R144
150K
150K
2.2/50
C141
Q106
Q107
R145
BD121
BD121
64
63
62
61
60
59
58
57
56
55
54
53
52
51
50
49
150K
C140
Q108 Q109 4K7 4K7
AGND
MGND
AGND
MGND
L122
L127
M-CR611 M-CR611 KRC102S D104 R148 R421
GND GND
GND GND
GND GND
GND GND
D105
R141
R142
-
NC
GND
NC
GND
PWDN
VDD
VDD
BICKO
EAPD
SDO_78
SDO_56
SDO_34
SDO_12
LRCKO
CH1_A
CH1_B
RA+ RA+
RA+ RA+
RB+
RB+
LA+ R146 0
LA+
LB+
LB+
RA-
RA-
RB-
RB-
LA-
LA-
LB-
10.REAR_USB_SW(OE2) LB-
10K
10K
1SS355T - -
33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
10P HEADER 10P HEADER
1
R147 22K
KRA102S
0
11.FRONT_USB_SW(OE1)
23.CY920_BCK/DSD_BCK
D_+12V
M-CR511 M-CR511
TO PF102_A
2
48.CH2_A
LA+
LA+
RA-
RA-
21.CY920_DATA/DSDL
LA-
LA-
Q111
100N
MGND
R149
R150
R151
R152
6P HEADER 6P HEADER
KTC2875B
KTC2875B
1.DSD_BCK
R154 Q110
R422
47.CH2_B
20K
20K
VDD NC
TO PF101_A
3
2.GND
KRA102S
1K
1K
Q113
Q114
4.DC/DC_1V8_ON
5.DC/DC_2V5_ON
6.DC/DC_3V3_ON
KRA102S
-
220/10
MGND R156
Q112
C145
KRC102S
KRC102S
R153
22.CY920_DSDR
25.CY920_MCLK
10K - GND GND
24.CY920_LRCK
3.FET_1V2_ON
C C
4
15K R155 10K
2.FET_5V_ON
CP102
12.OC_FLAG1
13.OC_FLAG2
19.FACT_RST
MGND
Q116
Q117
C144
TO CP813
16.SPI_MIEO
15.SPI_MOEI
R160 NC VDD
7.IOS(WIFI)
MGND
20.SPI_REQ
5
17.SPI_CLK
1.USB_OE
9.U_PWR1
8.U_PWR2
Q115 0
100N
C143
18.SPI_CS
14.E_RST
+29V
26.MGND
27.MGND
Q118 Q119 KRC102S DSD_R OUT3_A
6
KRC102S D106 D107 KRC102S R157
GND Reinforcement OPTION 1SS355T 1SS335T L103 BD121 DSD_L IC102 OUT3_B C146 C147
7
A_-12V 0
L101
L102
R524 0 R508 0 A_+5V
R158 22K R159 22K STA309A - -
L104 BD121 DGND OUT4_A C148 C149
0
CP102 A_+12V
R465 0 100P 100P
R527 0 R511 0 R161 R162 D108 SDI_12 OUT4_B
16 15 14 13 12 11 10 9
BTOB_27P
M-CR611 ONLY
MGND 1SS355T R466 0 LRCKI OUT5_A R472 47K
CY920_BCK/DSD_BCK
R528 0 R512 0 - 5K6 R471 47K
100/16
R166
C150
R467 0
150K
CY920_DATA/DSDL
JACK105
MGND MGND BICKI OUT5_B
PRE_OUT_MUTE
1SS355T
A_DC_PROT2
STA309_LRCKO
CY920_BCK/DSD_BCK
R529 0 R522 0
D121
STA309_DOUT
47P
47P
47P
47P
CY920_DSDR
STA309_BCKO
R165
VDD NC
CY920_DATA/DSDL
MGND
USB_SW_FRONT
HP_MUTE
CY920_DSDR A_DC_PROT1
R164
100N
C153
USB_SW_REAR
R530 0 R523 0
220/10
C345
GND GND
0
+5V_P_CONT
CY920_MCLK
E_FACT_RST
CY920_LRCK
+1V2_CONT
+1V8_CONT
+2V5_CONT
+3V3_CONT
47P
L-CH
E_SPIMOEI
E_SPIMIEO
C267
C266
C264
C263
C154
0
E_SPIREQ
34.OUT6_A
E_SPICLK
47P
U_PWR2
U_PWR1
E_SPICS
R531 0 NC VDD
USB_OE
MGND
U_FLG1
U_FLG2
IOS_ON
C155
100N
33.OUT6_B 3
MGND
E_RST
FILTER_PLL
R532 0
RESET
6 R-CH
C152
OUT8_B
OUT8_A
OUT7_B
OUT7_A
2
CKOUT
DIR_MCLK
DIR_LRCK
DIR_SDATA
PRE_OUT_MUTE
DIR_RST
CY920_BCK/DSD_BCK
DIR_SCLK
PLLB
HP_MUTE
D D
GNDA
VDDA
100N R473
GND
VDD
SDA
M-CR611 ONLY
SCL
R533 0 SW
XTI
NC
NC
A_5142_OTW
A_5558_MUTE
SA
A_5558_PDN
HP_ON
A_5142_SD
A_5558_RST
USB_SW_REAR
141126 D&M
5
+5V_P_CONT
IOS_ON
WPS_ON
STA309_RST
STA309_RST
R169 10K
I2C_SDA
I2C_SDA
SUB_P_CONT
0
I2C_SCL
I2C_SCL
HP_DET
+2V5_CONT
+1V8_CONT
+1V2_CONT
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
USB_OE
R537 0 R474
R177
R178
C158
R170 10K R171 10K
0
IC103 10K C160 100P
10N
C159
BD221
MGND
MGND
R173 10K R174 10K R175 47K R431 - R475 - R176 1

10K
10K
100N
ICS511
-
R192
R503
STA309_PDN
R180 47K
DSD_SCKO
10K
R179
0
0
0
0
SP_PROT
R181 R182 R183
-
-
R196
R197
I2C_SDA
220/10
I2C_SCL
100N
R435 47K
47P
47P
47P
C161
C163
47K
R191
-
X2 X1/CLK
10K
C165
CY920_BCK/DSD_BCK
8
10
10
R195 0 100K 100K
CY920_DATA/DSDL
ICS511_ON
R440
R439
C162
R193 10K R194 - OE VDD
R185
R186
R187
R188
R189
R190
7
10N
C349
C348
C347
- R464 L106 BD121
CY920_MCLK
CY920_LRCK
L105
S0 GND
C178
-
6
3
10K R184
10/16
10/16
C169 100P
DIR_RST
R202
10N
R203
R198 R509 0 CLK S1
C166 C167 C168 100N
CPU_+3V3 L128 1N 1N
4
R200
47
47
C157
C156
47K C170 100P
FPC102 C171 10N R199 10K BD121 3K4
C177
100N
FPC102 100
KTC2875B
AGND
C176 10N R201 C173 1200P
Q122
FPC_CNT_21P Q121
C174
C175
47K L107
KRA102S
220/16
220/16
309_+3V3
C179 100P BD121
- 141126 D&M
21.MGND C172 DIR_CE

21
10N C180 100P

E E
NFC_ACK
R208
R204
DIR_CLK
10K
TP3
10K
20.SPDIF C181 100P
A_+12V
20
A_-12V
DIR_DI
DIR_DO
C184 100P M-CR511 ONLY
19.MGND
19
R441 -
C182
C183
BD121
33
33
22
22
22
22
18.CD_SRAMSTB
18
L129
R442 -
0
0
0
0
0
0
0
220/6.3
R212 C185 100N
C187
Q123
C186
100N
17.BUS3 10K R434 10K BD121
17
R443 -
R219
KRA102S
10K
1K
R218 - L108
R205
R206
R207
R438
R209
R210
R211
R436
R437
R213
R214
R215
R216
R217
16.BUS2
16
R444 - IC104
BD121 R220
15.BUS1 L109 NJM4556
15
0
R222
R433
108 107 106 105 104 103 102 101 100 99 98 97 96 95 94 93 92 91 90 89 88 87 86 85 84 83 82 81 80 79 78 77 76 75 74 73
10K
10K
M-CR611 ONLY
R221
14.GND 0
14
R445 -
VCC
VCC
VCC
BUS1
BUS2
BUS3
VSS
DIR_DO
/HP_ON
VSS
DIR_DI
WPS_ACK
USB_OE
TEST3
IOS_ACK
HP_DET
DIR_RERR
DIR_CE
DIR_CLK
I2C_SCL
I2C_SDA
/SW_MUTE
NFC_ACK
/5142_OTW
/5142_SD
/HP_MUTE
SUB_P_CONT
CD_SRAMSTB
+5V_P_CONT
/5558_PDN
/5558_RST
/5558_MUTE
USB_SW_REAR
STA309_RST
R225
+1V8_NET_P_CONT
+2V5_NET_P_CONT
+3V3_NET_P_CONT
1
33
33
33
33
R224 0
1K
R223
220/16
0
0
0
13.BUS0 109 BUS0 72 0
C188
C189
Q124
120P
13
100N
R446 -
C190
C191
120P
E_SPICLK STA309_DOUT KTC2875B
R226 0
110 CD_CCE 71
D_+3V3
12.CD_CCE
12
R447 -
R238
GND -> 10K PU
2
R227
R228
R229
R230
R231
R232
R233
R234
R236 0 E_SPIMIEO STA309_LRCKO
1K
R235
11.CD_BUCK 111 CD_BUCK E_SPIMIEO 70
Q125
11
R448 -
R245
R246
KRA102S R237 Q135 R240
27K
3K3
R239 0
R251 3K3
E_SPIMOEI
R248
10.CD_CPSW 112 CD_OPSW E_SPIMOEI 69 0 KTC3875S C138
10
3
27K
R449 -
13
14
15
16
17
18
19
20
21
22
23
24
72./PRE_OUT_MUTE R241 33 47/25 4K7
AGND
9.CD_CLSW 113 CD_CLSW DIR_RST 68
F R450 - 71.E_SPICLK R499 100K
F
BCK
DOUT
DGND
MPO0
MPO1
LRCK
DIR_DO
DIR_DI
DVDD
SCKO
STA309_BCKOR242
STA309_DOUT
9
STA309_LRCKO
R243 0
VSS
M-CR611 ONLY
9 10 11 12
36 35 34 33 32 31 30 29 28 27 26 25
4
8.CD_INSW R451 - 114 CD_INSW DIR_INT 67 IC105
DSD_SCKO R244
8
0 C354 1000P NJM8068
C194
100N
R247 0 10N TP2 0 DIR_CE C192
7.CD_DECRST 115 CD_DECRST STA309_PDN 66
R250
STA309_DATAR249 100N
7
25.DIR_CLK
CPU_+3V3
0 12.STA309_BCKO R403 10K
10K
C164
1SS355T
1SS355T
1SS355T
3K3
C353 1000P
MODE
VCC
6.CD_DREQ 116 CD_DREQ TEST2 65 11.DSD_SCKO C195 C196
1
R452 - STA309_LRCKIR252
6
R497 47K
0 R253 0
100K
D109
D110
D111
C193
220/16
120P 120P
R255
R254 0 USB_SW_FRONT STA309_LRCKI 10.STA309_DATA E_DIN
R265
5.CD_SBSY R453 - 117 CD_SBSY USB_SW_FRONT 64
47K
3K3
STA309_BCKI R256
5
R258 0 R172 10K 0 R257 0
0
STA309_BCKI E_LRCK
AGND
2
R267 R268
8
4.CD_MSTBY 118 DRVMUTE +1V2_NET_P_CONT 63 C198 100N
R264
Q136
4
+3V3_CONT
C197
R478 0 R259 0
10N
R260 0
10K
10K
SCK E_BCK KTA1504S
7
119 CD_OPEN SP_PROT 62
10K
10K
3.CD_OPEN IC107 27K 27K
R498
R432
3
C199 10N PCM9211PTR R262 0
3
R263 33
R261
10K TU_RST MPIO_A3 E_SCK
6
2.CD_CLOSE 120 CD_CLOSE TU_RST 61
C200 C201
2
R479 0
AGND
R495
R496
100K
U_FLG1 R266 33 TU_CE MPIO_A2 DAB_SPDIF NET00239 560P 560P
47K
R279
R280
R281
R282
5
121 VBUS_FLUG1 TU_CE 60
VSS
1.CD_LDCHK
R270
R271
R269 100K
4K7
4K7
4K7
4K7
C202
1
4
R272
R273
R480 0
47K
100N
10N
U_FLG2 100N MPIO_A1 OPT1
1K
4
122 VBUS_FLUG2 VCC 59
10K
R274 100K
TO CN702
35.OPT2
R454 CS# VCC
R276
1
8
RESET
R278
36.VDDRX
R613 -
1K
10K ICS511_ON MPIO_A0 RST
KTC3875S
KTA1504S
3
123 CD_LDCHK ICS511_ON 58
SO/SIO1 HOLD#
R481 0 C209 C210
Q137
Q134
C204
100N
NPCM
0
CD_SPDIF
C203
U_PWR1 C205 470P 470P
R287
R288
R289
R290
R275
R277
2
124 VBUS_CTL1 VSS 57
AGNDAD
C207
4K7
4K7
4K7
4K7
GNDRX
10N WP# SCLK ERROR
VCCAD
3
VCOM
IC112
AGND
R283 0
C206
G G
U_PWR2 OLED_3V3_CONT NET00322
VINR
VINL
VCC
TXO
1
125 VBUS_CTL2 OLED_3V3_CONT 56
R284
KDS160
FLT
R5F56108VNFP
TXI
R455 10K R429 GND SI/SIO0
MGND
4700P
KDS160
4
220/6.3
E_FACT_RST
C211
100N
D114
D118
R285 0 10K E_RST
BD121
BD121
BD121
BD121
126 E_FACT_RST E_RST 55 NET00321
C208
48
47
46
45
44
43
42
41
40
39
38
37
L110
L111
L112
L113
WPS_ON
R291
R292
AGND
R506 0 R286 0
22K
22K
TLC59108_RST
TP4 127 TEST4 TLC59108_RST 54 IOS_ON
R484
100K
R295 R293 0 IC106 SP_PROT
GD25Q32_HOLD
LED_OR GD25Q32_HOLD C352
128 LED_ORANGE GD25Q32_HOLD 53
GD25Q32_CLK
GD25Q32B
R494
10K C212 100N R294 0
GD25Q32_WP
GD25Q32_SO
GD25Q32_CS
R297
100N
GD25Q32_SI
10K
R309
100
LED_RED R296 0 E_SPICS
C213
100N
129 LED_RED /E_SPICS 52
-
CBW160808U121T
C216 C214 22/16
C215 R298 0 GD25Q32_WP
130 VSS GD25Q32_WP 51
R485
100K
C351 C350 SP_P_CH
10K
10K
100N M-CR611 K Region ONLY
CLZ9R001Z ->
D_+3V3
R317
100N R299 0 OLED_P_CONT C219 100N 220/25 220/25 SP_M_CH
R304 680
R307 131 LED_GREEN OLED_P_CONT 50
-
LED_GREEN
10K 0
4700P
C221 R301 0 EEPROM_SCL
C222 22/16 C223 16P R505
MGND
132 VCC EEPROM_SCL 49
10N
BD121
C220
220/6.3
R303 0 IC108
R482
R483
EEPROM_SDA
133 REGION(0.0V:K1(CN)/1.65V:F(JP)/2.47V:U1(NA)/3.3V:N1(EU)) EEPROM_SDA 48
24.576MHz
TAS5558DCAR
R305
R306
R311 R308 0 GD25Q32_CS 2 1
MGND
SUB_P_CONT
R310
X101
134 MODEL(L(0V):MCR511, H(3.3V):MCR611) GD25Q32_CS 47
R315
470
C224
100K
0
1M
4700P
R302 R312 0 GD25Q32_SO PWM_HPM_L
29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56
C225 68N
3 4
1
REGION 10K 135 DC_PROT1 GD25Q32_SO 46 IC109 PWM_P_6
R318
R300
470
R1EX24128BSAS0I PWM_HPP_L
C234 220/6.3
R307 R309 R317 R314 0
NET00069
NET00070
4700P
GD25Q32_SI
R459
-
2
136 DC_PROT2 GD25Q32_SI 45 AGND PWM_M_6
L114
C232 100N
C233 100N
EU 10K OPEN OPEN C226 16P
H R313 REMOTE
H
PWM_HPM_R
R316 0
47N
GD25Q32_CLK
NA 10K 15K 15K
3
137 REMOTE_IN GD25Q32_CLK 44
-
SDA GND PWM_P_5
C227
5
4
100K MGND MGND
R322 4K7
R323 4K7
JP 10K 10K 0 KEY3 R319 0 E_SPIREQ PWM_HPP_R C230
+29V
4
138 KEY3 E_REQ 43
47N
CH OPEN 10K 0 R460 SCL A2
R320 47K PWM_M_5 100N
6
3
HP_DET
C228
L115
100N
10K R321 0
C239
C240
C229
TU_SCL AVSS VR_PWM
5
139 KEY2 TU_SCL 42
10N
WP A1 0 R325
7
2
P_DOWN KEY2
PLL_FLTM
R461 C235 100N 5558_+3V3
6
4
3
140 VREFL PLLVSS 41
C231
MODEL 10K VCC A0 R500 - AVSS_PWM
8
1
L116 1 PLL_FLTP
R302 R300 R326
_PF103
KEY1 TU_INT
7
5
2
R462 141 KEY1 TU_INT/DO 40 AVDD_PWM
611 10K OPEN 33
R324
R481 R485 R500 PWM_P_8 PWM_P_8
10K 0 VR_ANA
100/6.3
C236
511 OPEN 10K
RXD_MI232O
8
6
1
142 VREFH PLLVCC 39
TXD_MO232I
R329
511 OPEN OPEN 0 PWM_P_8
TU/DAB_ON
EL_R/W,WR
C242
0
P01/TRST#
IC111 PWM_M_8 PWM_M_8

R328
D_+3V3
611
C237
C238
R327
0 100K OPEN
TU_SDA AVDD PWM_M_8
10N
10N
EL_E_RD
P_DOWN
PF103
AIN_CNT
28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9
143 AVCC TU_SDA/DI 38
100N
FDC608 18P
-
EL_RST
BI_AMP
33
10N
KRC102S
220/10
R330 15K
RESET
EL_DC
EL_CS
PWM_P_7 PWM_P_7
TEST1
ASEL_EMO2
XOUT
EMLE
Q126
AVSS
C251
144 TCK D0 37 1.DGND
MDE
MD1
MD0
TMS
TDO
VCC
TCK PWM_P_7
VSS
VSS
VCL
NMI
XIN
PWM_P_8
TDI
R331 47
D7
D6
D5
D4
D3
D2
D1
DIR_MCLK PWM_M_7 PWM_M_7
1
C244 MCLK PWM_M_7
2.PWM_P_8
C247 47/35
R463
10N
MGND
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 R332 18K-F
10K
22
C253
C254
100N
OSCRES PWM_P_4
10N
3R3
10K
10K
10K
10K
3.SP_P_CH
C248
C249
CPU_+3V3
C250 10N PWM_M_8

100N
D122 1SS355T D112 1SS355T DVSS2_CORE
3
22
33
4700N
4.PWM_M_8
C252
PWM_M_4 SP_P_CH
-
TMS
100N
10K
10K
4K7
100N
DVDD2_CORE
220
C256
10K
R333
IC113 AZ1117CH-3.3TRG1 L118 IC110

33
33
33
33
33
22
22
22
22
22
22
22
22
22
22
PWM_P_3 5.SP_M_CH
A_+5V
LM7805
J J
PWM_P_7
100N
-
IN OUT
R334
R335
R336
R337
R338
A_+12V
A_-12V
5
R339
R504
R360
C255
3 2 MGND EMO1 PWM_M_3

TU/DAB_ON
R340
D113 6.PWM_P_7
AIN_CONT
1
BD121 1K
1
SP_M_CH
R362
C258 100N AGND

1SS355T R361 33
NJM2387ADL3
A_5558_RST PWM_P_2 PWM_P_2

C259
15K
C257
R425
VIN CON RESET PWM_P_2

R341
R342
R343
R344
R345
R424
R346
R347
R348
R349
R350
R351
R352
R353
R354
R355
R356
R357
R358
R359
7.5142_+12V
MGND
C261 100N PWM_M_7

220/10 C243 100N HP_ON R363 33 PWM_M_2 PWM_M_2
7
C246
C245
100/16
C260 D115 HP_SEL PWM_M_2
8.PWM_M_7
GND 5 1SS355T
R426
L117 R365 33 PWM_P_1 PWM_P_1

10K
IC114
R366 10K 100/16 C262 PDN PWM_P_1

9.+29V
R427
L121 BD121
R364 D116 PWM_P_2

R368
VOUT VOUT
10K
D117
VADJ
R367 33
10
220/10 PWM_M_1 PWM_M_1
1K
9
47K 1SS355T BD121 MUTE PWM_M_1
10.PWM_P_2
0
FPC106 3 6 C265 1000P C241 R369

4
100N
100N
100N
100N
100N
TDI
EL_RST
EL_RW
EL_RD
EL_DC
TP1
MGND
EL_CS
C271
10N
100N
UPGRADE 4P C268 OLED_3V3_CONT 220/10 SDA VALID
11.OTW
10N
D7
D6
D5
D4
D3
D2
D1
D0
C280 1000P
R428 C269 10N 47 PWM_M_2
C270
12
11
R430
10K C283 10/6.3 SCL DVSS1_CORE

10K
R371
4.GND 47/50 C279 1000P C273 100N 12.PWM_M_2

1K6
TRST 100N R370 47

4
AGND
C272 LRCLK
C274
C275
C276
C277
C278
R502 C284
100/16
C285 10N 13.5142_SD

C287
3.RXD_232 DVDD1_CORE
R373
NET00032 NET00032 100N - 100N R374 47 C294 4700N

PWM_P_1
3
3 2 1
14
13
R372
CPU_+3V3
C288 100N SCLK BKND_ERR
47
47
R377
R375 - C355
BD221
14.PWM_P_1
C281 47P
C282 47P
2.TXD_232 1
C299 220/6.3
L123
10K
NET00033 NET00033 2 3 AGND

R376 47
2
10/16 C289 1000P C303 100N

GND
NC
SUB
1000N
C286
C291
C292
C293
C290 SDIN1 PSVC/MCLK
10N
10N
10N
1.CPU_+3V3 C308 IC116 PWM_M_1
15.VALID
EMLE X102 1000P
R381
1
16
15
- R380 AZ1117CH-3.3TRG1 C295 10N A_+12V
100
12MHz IC117 100N C301 1000P SDIN2 TEST

16.PWM_M_1
R378
R379
TDO BD4730 R383 C297
4K7 R382 D120 100N C298 100N C305 10N R390 47 SDIN2_1
VOUT
VCC
1000P
C312 100N
K K
100N
KDS160 LRCLKO(LRCK_2)
R385
47K
FPC101 MD1 10K
10N
C316
3
ST+5V
BD121
A_-12V SDIN2_2
D119
4K7 R384 R501

TO PF103_A
1.0_7P C302 1000P
14P
100N SCLKO(SCLK_2)
0
MGND
MD0 220 C306 10N

4
4 5 NFC_ACK
KRC107S
VR_DIG
KRA102S
33
33
14P
R386 C313 100N Q127

D_+3V3
-
SDOUT(SDIN5)
KRC107S
A_+5V
RESET
C315
C309
C310
C311
1
1K C307 1N C296 1000P
Q128
Q129
R388 10K
C314
+3.3V_CPU - Q130 C300 10N L125 BD121

2
NET00064
R415
R615
R389
R391
KRC102S R387 Q131 C304 100N
10/16
TXD
L124
C317
NET00033
R392
100K
3
RESET KRC102S R615 R391

- R393
C330 1000P
511
RXD OPEN 33
C332 100N
NET00032
-
4
BI_AMP
C331 10N
R416 MGND
BI_AMP C319 18P 611 33 OPEN
GND_D
5
C318
100N
Q132 C320 18P

C327 1000P
R395
MGND
C329 100N
KRA102S 10K
C328 10N
CNVSS MD0
R394 C321 18P
6
MGND
-
DSP_BOOT MD1
7
A_5558_MUTE
R398 10K R399 5558_+3V3
A_5558_PDN
C322 100N
TU_SCL
TU/DAB_ON
TU_SDA
TU_RST
DIR_SDATA
R397
TU_INT
TU_CE
NET01088
DIR_LRCK
DIR_SCLK
C323 100N
AIN_CONT
A_5142_OTW
R402
I2C_SDA
10K
I2C_SCL
R401 10K 10K
A_5142_SD
C325 10N I2C_SDA C324 100N
R405 R477 0
0
TLC59108_RST R404 -
EL_RW
LED_RED
D7
D5
D3
D6
D1
D4
D2
D0
EL_RD
EL_DC
EL_CS
KEY3
KEY2
KEY1
EL_RST
REMOTE
LED_GREEN
LED_OR
C326 1000P I2C_SCL

- R476 0
L TMS R406 10K
L
11
TMS
Q133 R408 10K
1000P
KRA102S L126
100N
C340
C341
C342
10
TDO TDO
10N
C333 100N BD121

TRST# TRST D_+12V 5142_+12V
9
C334 10N R456 10K

EMLE EMLE
C335 1000P R457 10K R411 10K C151
8
D_+5V
R458 10K NET00321

C339 1000P
MD1 MD1 C336 100N

C337 100N
7
_CP103
C338 10N
1000P AGND
MD0 MD0 C343 10N
6
MGND
R163
NET00322
C344 1000P 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32
GND_D
0
5
MGND
FPC104 CP103
TCK TCK
FPC_CNT_33P 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 WAFER_11P 5 4 3 2 1
4
R167 Q120 CP104 CP106

MGND
TDI TDI
_FPC104 BSS138 WIRE_5P
TO __FPC1
- BTOB_23P
3
10.TU/DAB_ON
1.D_+3V3
11.+18V_OLED
15.TU_INT/DO
10.OLED_+16V
12.OLED_+16V
12.TU_SDA/DI
3.LED_GREEN
19.AIN_CONT
2.DGND
5.GND_DRV
8.OLED_+3V3
(511 : 5P)
3.OPT1
4.OPT2
12.NFC_ACK
+3.3V_CPU R168
3.POWER_H
9.STBY_+5V
32.LED_RST
2
4.CPU_+3V3
14.TU_RST
31.LED_+5V
33.LED_+5V
11.TU_CLK
5.WPS_ON
30.I2C_SDA
29.I2C_SCL
1.LED_RED
1.P_DOWN
2.D_+12V
23.R_OUT
26.EL_RST
6.REMOTE
13.TU_CE
21.L_OUT
CPU_+3V3
7.LED_OR
25.EL_RW
4.D_+5V
16.DGND
5.HP_DET
2.BI_AMP
20.AGND
22.AGND
8.D_+12V
1.DGND
3.DGND
4.A_+12V
20.EL_RD
24.EL_DC
27.EL_CS
10.DGND
6.A_-12V
RESET
8.ST+5V
9.ST+5V
15.DGND
22.DGND
28.DGND
17.A+5V
18.A+5V
6.SPDIF
7.DGND
10K
1
7.DGND
11.KEY1
5.AGND
TO FRONT
2.KEY3
9.KEY2
13.D7
14.D5
16.D3
17.D6
18.D1
19.D4
21.D2
23.D0
FPC101 1 2 3 4 5
M 1.0-11-11P
M
MGND
511 D_+3V3 DGND OPT1 IOS_ON WPS_ON
SCHEMATIC DIAGRAMS (1/10)

FPC103 611 D_+3V3 DGND OPT1 OPT2 WPS_ON
_CP106
TO CN221 TO __CP1
GND LINE POWER+ LINE POWER- LINE ANALOG SIGNAL L ANALOG SIGNAL R DIGITAL SIGNAL SUBWOOFER
SCH01_MAIN_MCU_PWM
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
56
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
CP805
MCR511/611 NETWORK _PCB ASSY
8.2P(2012)
141118
C830
L803 BD221 R826 -
REF_NO: 800~
AVIN 1000N
C825
NET_5V NET+5V
NET_5V
L804 BD221
NET_5V
169K
4 5 6
FDC608
47K
R827
1000N
N_GND
IC802
C829
R930
16
15
14
13
10K
100N C826
C828 100N
N_GND 3 2 1
C827 -
348K
AGND
VFB
NC
R829 100K
R828
N_GND POK TST0
17
12
AVIN
R831 10
76K8
PGND
0
KRC102S R830
E_POWER3 ENABLE TST1 NET00250
18
11
8.2P(2012)
R832
16
15
14
13
CP805
2K
L805 PVIN TST2
19
10
B CB05YTYH221
B
348K
VFB
NC
AGND
R834 100K L806
R833
Q800
PVIN PGND
20
POK TST0 CB05YTYH221
R835
17
12
FET_5V_ON
R836 10
TO CN223 NC(SW) PGND
PGND
21
ENABLE TST1
8
E_POWER1
18
11
141118
22UF-16V(X5R)
R837
C831
L811 L807 NC(SW) VOUT NET_1V8
22
PVIN TST2
7
0
19
10
CB05YTYH221 CB05YTYH221 L809
22UF-6.3V
10UF-6.3V
L812 NC(SW) VOUT
PGND
23
PVIN PGND CB05YTYH221
6
20
EN5339QI
CB05YTYH221
R838
141118 NC(SW)
24
10K
NC(SW) PGND
5
VOUT
21
22K
22K
22UF-16V(X5R)
IC803
-
-
1N
-
C838 100N
-
L814 NC(SW) VOUT NET+3.3V
22
7
CB05YTYH221
22UF-6.3V(X5R)
10UF-6.3V(X5R)
L816
4
PGND
R839
C832
C833
C834
C835
C836
C837
C840
C841
C842
VOUT
NC(SW) VOUT
C839
23
CB05YTYH221
R936
EN5339QI
NC(SW)
10K
PGND
PGND
NC(SW)
24
100N
5
VOUT
22K
22K
-
IC804
-
1N
-
4
R840
R935
C846
C847
C850
C851
C852
C854
C855
C856
VOUT
C853
PGND
PGND
NC(SW)
C848
C849
C C
8.2P(2012)
E_POWER4
100 R855 WIFI WIFI R933
C941
SW800 Q801
R854 - IC805
C862
IOS -
0 -
100N
C863
R856
GND_D
-
0
L829
AVIN 1000N
AVIN 1000N
C857
C858
GND
316K
110K
-
R932
8.2P(2012)
L828
E_POWER1
16
15
14
13
16
15
14
13
-
348K
348K
AGND
VFB
NC
AGND
VFB
NC
R846 100K R847 100K
R843
R844
R845
POK TST0 POK TST0
17
12
17
12
D R931 R848 10 R849 10
D
PGND
PGND
ENABLE TST1 E_POWER2 ENABLE TST1
18
11
18
11
BKT802
-
GND_OPTION
C861
L820 L821
R850
R851
PVIN TST2 PVIN TST2
0
19
10
19
10
CB05YTYH221 L822 CB05YTYH221 L823
141128 PVIN PGND PVIN PGND
20
20
R934 0 CB05YTYH221 CB05YTYH221
9
R852
R853
NC(SW) PGND NC(SW) PGND
21
21
22UF-16V(X5R)
8
8
22UF-16V(X5R)
L824 NC(SW) VOUT R942 0 L825 NC(SW) VOUT
22
22
7
7
CB05YTYH221 CB05YTYH221
10UF-6.3V
L826 L827
22UF-6.3V
22UF-6.3V
10UF-6.3V
NC(SW) VOUT NC(SW) VOUT
PGND
PGND
23
23
CB05YTYH221 CB05YTYH221
6
EN5339QI
EN5339QI
BKT801 NC(SW) NC(SW)
100N
-
-
24
24
10K
100N
5
5
VOUT VOUT
NET_2V5
22K
22K
IC806
IC807
-
-
1N
1N
-
-
-
1
4
R857
R858
R859
R860
C864
C866
C867
C868
C870
C871
C872
C873
C874
C875
C876
C877
C878
C879
C880
C881
C883
C884
C885
VOUT
VOUT
C869
C882
C865
R937
PGND
PGND
PGND
PGND
NC(SW)
NC(SW)
NET+5V
GND_D GND_D
E NET+3.3V NET+3.3V
E
NET_1V2
TPS2065CDBVR R801 0 NET_1V8

OC_FLAG1
NET+5V
2.0mm USB WIRE IC800
NET+5V
CN807 R800 0 L842
I2C_SDA1
I2C_SCL1
U_PWR1
L800 BD221 BD221 NET_2V5
vbus 1 OUT
IN 5
-DATA R803 BD221 2 GND

100/6.3 C803
L843
10K
L830
-
0
+DATA 3 FLAG
EN 4 BD221
-
1N
1N
GND C886 - C887 1N

NET00390
R804
C805
C801
C802
C804
100N
C888 100N C889 100N
NET_1V8
NET_1V2
C800
0
F F
L831
C890 1N
0
R861
R862
C891 100N
8
C892 1N
7
USB_OTG_DN_1
6
USB_OTG_DP_1
5
100N
C893
C894
100N
100N
IC808 C895
MFI337S3959
GND_D
IC809 IC810 CN801
47K
75K
75K
47K
47K
75K
75K
47K
L832 0 CN802
C896
100N
BD11600NUX BD11600NUX
-
-
C897
C903 1000N
2
1
1
0
C898
1D- VCC
9 10
9 10
VCC 1D+
C909 100N
1
C920 100N
R863
R864
R865
R866
R867
R868
R869
R870
R871 R872
3
4
4
1D+ S S 1D-
2
1000N
C899 100N
C910
G 0
G
5
6
6
2D+ D- D+ 2D+
3
C859 1000N
4K7
4K7
10K
10K
0
7
8
8
2D- D+ D- 2D- 1.0mm FPC WAFER
4
R873 0 R874 C860 100N
64 62 60 58 56 54 52 50 48 46 44 42 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10
64 62 60 58 56 54 52 50 48 46 44 42 40 38 36 34 32 30 28 26 24 22 20 18 16 14 12 10
9
9
GND OE OE GND
5
C844 1000N NC
7
R875
R876
63 61 59 57 55 53 51 49 47 45 43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11
63 61 59 57 55 53 51 49 47 45 43 41 39 37 35 33 31 29 27 25 23 21 19 17 15 13 11
R877
R878
C845 100N NC
-
USB_OE USB_OE
6
GND
C901
5
FRONT_USB_SW FRONT_USB_SW C900 100N
BKT800 E_RESET
DEBUG_RX
M3 BRAKET
4
REAR_USB_SW REAR_USB_SW
USB_D+
OC_FLAG2 OC_FLAG2 - C902 DEBUG_TX
3
USB_D-
IC811 +3.3V
2
TPS2065CDBVR R883 0 BCO_SPDIF
L833 0 L834 0 NC
1
CP809 R890 0*4
1 OUT
IN 5
R885 -
R886 0 E_SPI_MOEI CP808
VBUS 2 GND
5
L835 0 R888 100
4
E_SPI_MIEO NET/USB_MCK
-DATA 3 FLAG
EN 4 U_PWR2
H CP813 H
6
3
R889 100
GND_D
R882 E_SPI_CLK NET/USB_LRCK
+DATA 0
100/6.3
7
E_SPI_CS R891 100 CASMOS BD TO BD
10K
NET/USB_BCK
-
1N
GND
8
100N
R893 100
L836
NET/USB_DSDR
1N
R892 10K
0
R894 0 R896 100 NET/USB_PCM_DATA/DSDL 27.MGND

E_FACT_RST
R895
C904
C905
26.MGND
C907
C908
C906
I2C_SDA1 R897 BD121

R898 - R899 - NET/USB_MCK NET/USB_MCK_1 25.CY920_MCLK
-
I2C_SCL1 R900 0
NET/USB_LRCK NET/USB_LRCK 24.CY920_LRCK
R901 - R902 - R903 - R904 - R905 BD121
C911
NET/USB_BCK NET/USB_BCK1/DSDBCK 23.CY920_BCK/DSD_BCK

R906 0
E_SPI_REQ NET/USB_DSDR NET/USB_DSDR_1 22.CY920_DSDR
R907 0
NET/USB_PCM_DATA/DSDL NET/USB_PCM_DATA/DSDL 21.CY920_DATA/DSDL
GND_D
ETH_TX+
E_SPI_REQ 20.SPI_REQ
R908 10K
E_FACT_RST 19.FACT_RST
FROM MAIN PCB ASSY

ETH_TX-
J ETH_RX+
E_SPI_CS 18.SPI_CS J
RJ45_CH
33*4 E_SPI_CLK 17.SPI_CLK

R910 ETH_RX-
E_SPI_MIEO 16.SPI_MIEO
FLASH_CLK
E_SPI_MOEI 15.SPI_MOEI
4
R909 - FLASH_DIN USB_OTG_DN_1

E_RESET 14.E_RST
3
FLASH_DOUT
RJ45
ETH_TX+ USB_OTG_DP_1 OC_FLAG2 13.OC_FLAG2
2
4 3
JACK800 DLW21SN900HQ2L INT_FLASH_CS
U_PWR_EN R911 - R912 0 OC_FLAG1 12.OC_FLAG1
L837
1
1 2 U_OTG_VBUS R913 0 FRONT_USB_SW

-
TD+ ETH_TX- 11.FRONT_USB_SW(OE1)

1
R914 -
TD- R916 - R917 10K REAR_USB_SW
10.REAR_USB_SW(OE2)
FLASH_HOLD
FLASH_WPROT
R915 10K
2
R922 -
R918
R919
R920
R921
U_PWR1
9.U_PWR1
EXT_FLASH_CS
RD+
3
U_PWR2
TCT ETH_RX+ 8.U_PWR2
10K
R923
4
3
L839
4 DLW21SN900HQ2L WIFI 7.IOS(WIFI)
RCT L838
K BD121
K
5
1 2 E_POWER1 6.DC/DC_3V3_ON
RD- ETH_RX-
6
E_POWER2 5.DC/DC_2V5_ON
NC
7
R924 - E_POWER3 4.DC/DC_1V8_ON

GNDC
8
E_POWER4 3.FET_1V2_ON
0
FET_5V_ON 2.FET_5V_ON
R925
SW801 USB_OE 1.USB_OE

C914 100N
C912
C913
1N
100P
EXT_FLASH_CS
C915 1N R926 0
TO CP102
-
IC812 INT_FLASH_CS
MX25L25635FMI-10G
R927
0 R928 -
DNU/SIO3 SCLK
9 10 11 12 13 14 15 16
FLASH_HOLD FLASH_CLK
1
R929 10 L840
NET+3.3V VCC SI/SIO0 FLASH_DOUT
2
22N
L L
-
L841 RESET# NC CP811

100N
0
1N
NC NC
4
FLASH_CLK SCK
1
GND_D
NC NC
5
C918
C917
C919
C916
DGND
2
NC NC
6
FLASH_DOUT MOSI
3
RJ45_CH
EXT_FLASH_CS CS# GND

7
D_3.3V
4
FLASH_DIN SI/SIO1 WP/SIO2 FLASH_WPROT
8
CS
5
FLASH_DIN MISO
6
-
-
-
-
1N
1N
1N
1N
1N
1N
1N
1N
1N
1N
100N
DGND
7
C922
C923
C924
C927
C928
C929
C930
C931
C932
C933
C934
C935
C936
C937
C938
C939
C940
1.0mm FPC WAFER

GND_D
M SCHEMATIC DIAGRAMS (2/10) M
GND LINE POWER+ LINE POWER- LINE ANALOG SIGNAL L ANALOG SIGNAL R DIGITAL SIGNAL SUBWOOFER SCH02_MAIN_NETWORK
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
57
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
REF_NO: 800~
B MCR511/611 NETWORK PCB ASSY B
C C
R802 0
CP800
2.0mm WAFER
TO NETWORK PCB
JK901 L810
DLP11SN121SL2L
VBUS VBUS
-DATA -DATA
D D
GND_CH
USB_OTG_DN
+DATA USB_OTG_DP
+DATA
GND GND
100/6.3
R805 0
-
R806 0
C806
C843
GND_D1
E E
MCR511/611 FRONT_USB B'D
OPTICAL B`D
F
MCR611 C954
0-1608
F
BKT901
CP812 C953
TO INPUT PCB
0-1608
OPT_OUT2
R938 - JK810 OPT JACK 1
C956
GND_D
10P
R939 0 C944 0
OPT_OUT1 OUT
1
GND_D GND_D OPT1
2
10/16
100N
3V3 3V3
3
CP812
G G
10P
C942
C943
COSMOS_5P_AN
DGND1
CP803
TO CP3
C957
JK811 OPT JACK 2
ADC3 CP804 R940 0 C945 0
OUT
1
ADC2 R941 -
GND_D OPT2
2
GND COSMOS BD TO BD
3V3
3
ADC1
CP804
ADC0
AUDIO_L DAB_R
DAB_R
AGND AGND
DAB_L
AUDIO_R DAB_L
SCL0
H DO
H
TO NETWORK PCB
SDA0 DI
NC
OPTICAL B`D
DGND
IRDATA_IN DAB_ON
POR_N L801 +5V
MCR511
3V3 OUT IN +5V
MAX 300mA L802 0
GND 0 DGND
R819 R815
ADJ
R816
CONT
3K6
1V1 R2 GND SPDIF

-
DAB_TX_M_RX TUNER_SDIO/DAB_TX
11K
22/6.3
1N-K
TO CP2
10K
DAB_RX_M_TX TUNER_INT/DAB_RX AP7361-sot89-5

IC801
C819
10/16
GPIO
GPIO
C822
R821
R1
4K7
MFIO22
TO CNT PCB
J R822 Vref =0.8V
J
C821
MFIO23 Vo=Vref(1+R2/R1)
100 R948
SPI_CLK WPS WPS
100 R949
SPK_TXD IOS IOS
C947 100N
C946 100N
0 R950
-
OPT_OUT1
GND DGND1 - R951
GND_D
C955
10P
PWM3(SPDIF)
3V3
R947
R946
10/16
C949 100N
0
CP821
5P_WAFER
C950
C948
DGND1
0
C951
0-1608
0-1608
C952
SW914 SW913
R944
R943
K K
1 2 3
iOS WPS
BKT900
JK900
3V3
OUT
GND_D
MCR511/611 DAB B'D OPT JACK 1
L L
M M
SCH03_MAIN_DAB
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
58
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
MCR511 / 611 CNT

REFERENCE NO.
1 ~ 101
B B
C C
D D
CONNECTOR
FPC4
NC / I2C_SCL
MCR511(29P)
LED_GREEN
MCR611
+16V_OLED
+16V_OLED
EL_RW,WR
EL_RESET
MCR611(33P)
+3V3_CPU
OPTION
LED_RED
LED_RST
E E
REMOTE
I2C_SDA
+3V3_D1
LED_OR
H/P DET
LED_5V
LED_5V
EL_D/C
GND_D
GND_D
GND_D
EL_RD
EL_CS
KEY3
KEY2
KEY1
D7
D5
D3
D6
D1
D4
D2
D0
FPC4 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33
FPC_CNT_33P
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32
C61 100N-K
MCR611
OPTION
C64 10N-K C67 100N-K
LED_GREEN
C68 1N-K
LED_RED
3V3_CPU
C69 10N-K
REMOTE
H/P_DET
LED_OR
KEY3_1
3V3_D1
EL_RW,WR
EL_RESET
16V_OLED
C70 1N-K
LED_RST
I2C_SDA
DGND_1
I2C_SCL
LED_5V
KEY2_1
KEY1_1
EL_D/C
EL_RD
EL_CS
F F
D7
D5
D3
D6
D1
D4
D2
D0
C72 100N-K
C73 10N-K C74 0
C76 1N-K C77 0
C81 0
C83 100N-K
C84 10N-K C85 0
C86 1N-K C87 0
C88 0
C91 10N-K
C92 10N-K
G C93 10N-K G
DGND CH_GND
CP6
FPC_CNT_34P
NC / I2C_SCL
+3V3_CPU
LED_RST
NC / I2C_SDA
LED_GREEN
+3V3_D1
LED_RED
+16V_OLED
GND_D
KEY1
REMOTE
+16V_OLED
H/P DET
LED_5V
LED_5V
KEY3
KEY2
LED_OR
EL_RESET
EL_D/C
EL_CS
D7
D5
D3
D6
D1
D4
D2
D0
EL_RW,WR
GND_D
GND_D
EL_RD
MCR611
OPTION
NC
CP6
H MCR511(30P) H
MCR611(34P)
J J
K K
L L
GND LINE POWER+ LINE POWER- LINE ANALOG SIGNAL L ANALOG SIGNAL R DIGITAL SIGNAL SUBWOOFER SCH04_CNT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
59
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
B B
C C
D D
E E
NFC
F F
NFC ANTTENA
FROM NETWORK PCB

4 3
1R5
18P-J
NTAG203F
IC901
R958
C956
1 2
NFC_INTRP
100N-K
C958
DGND
2
G G
CN910
2P WIRE
2.0mm WIRE
H H
J J
K K
L L
M M
SCH05_NFC
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
60
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
Ref No : 500 ~ 600
B B
MCR-611 AMP
C500 100/16
C501 C502
10000N/25V L500 L501 10000N/25V
BD120 BD120
1000N
1000N
1000N
1000N
C504
C505
C506
C507
C508
C509
C510
R551
C511
C R550
C
10N
10N
10N
10N
10 10
C503
IC500 3300/50 PF101_A
TO MAIN UNIT PF101_A

C512 TAS5142DKDR
100N C513 100N
19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
GVDD_B GVDD_A
1
C514 33N(20)
OTW BST_A
2
R552 C515 100N L502
330P/100V
0
C516
SD PVDD_A PF101_A
4700(M)
3
10uH
C517
47N
PWM_A OUT_A
R558 R554
4
C5001
18-F 18-F
C521
C522
RESET_AB
1000N RB+
5
DGND_A
R553 0 R555 51K
RB+
-
PWM_B DGND_B
C5002
330P/100V
C518
Q500 R556 56K 1000N R557 51K
C519
KRC107S RB-
47N
OC_ADJ OUT_B
7
C520 100N L503
C523
DGND PVDD_B RB-
8
C525 100N C524 33N(20) 10uH
D AGND BST_B GND
D
18 17 16 15 14 13 12 11 10 9
C526 33N(20)
VREG BST_C GND
L504
330P/100V
Q501 C530 100N
C531
KRA107S RA+
4700(M)
M3 PVDD_C
C527 1000N 10uH
C532
R559 51K
47N
M2 OUT_C RA+
R562 R561
C5003 R560 51K
18-F 18-F
M1 DGND_C 1000N RA-
-
C528
C529
PWM_C DGND_D
C5004 RA-
C533
330P/100V
1000N
R563
C534
1K
RESET_CD OUT_D
47N
C535 100N L505
C536
PWM_D PVDD_D
C538 33N(20) 10uH
TO _PF101
VDD BST_D
C540 100N C541 100N
C537 R564
PF103_A 100N 1K GVDD_C GVDD_D
FROM MAIN UNIT PF103_A
R565 1 L506 L507 C544
C542
100N
C539
100/16
BD120 BD120 10000N/25V
E E
16
16.PWM_M_1
R566 R567
C543
CN500
FROM SMPS UNIT

10000N/25V 10 10
15
15.VALID
14
14.PWM_P_1
C545
100/16
13
13.5142_SD
12
12.PWM_M_2
11
11.OTW
CN500
C549
C547
C548
100N
10N
10
10.PWM_P_2
1N
9.+29V +29V
9
-
8.PWM_M_7 +29V
8
7.5142_+12V ADGND
7
6.PWM_P_7 ADGND
6
R589
+29V
F F
5.SP_M_CH
5
4.PWM_M_8 +29V
4
10N
C598
C597
C550
100N
-
3.SP_P_CH
3
2.PWM_P_8
2
1.ADGND
1
C551 100/16
TO CN411
-
PF103_A
C552
R569
R570
L508 C553
10000N/25V L509 10000N/25V
BD120 BD120
TO _PF103
1000N
1000N
1000N
1000N
R571 R572
C555
C556
C557
C558
C559
C560
C561
C562
10
10N
10N
10N
10N
10
C554
IC502 3300/50
C563 TAS5142DKDR PF102_A
TO MAIN UNIT PF102_A

G 100N C564 100N G
19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36
GVDD_B GVDD_A
1
C565 33N(20)
OTW BST_A
2
L510
330P/100V
R573 0 C566 100N
C567
SD PVDD_A PF102_A
4700(M)
3
10uH
C568
47N
PWM_A OUT_A
R579 R575
4
C5005
18-F 18-F
C572
C573
RESET_AB
1000N LB+
5
DGND_A
R574 0 R576 51K
C5006 LB+
-
PWM_B DGND_B
330P/100V
C569
Q502 R577 56K 1000N R578 51K
C570
KRC107S OC_ADJ OUT_B LB-
47N
7 C571 100N L511
C574
8 DGND PVDD_B LB-
C576 100N C575 33N(20) 10uH
AGND BST_B GND
18 17 16 15 14 13 12 11 10 9
C577 33N(20)
VREG BST_C GND
Q503 C581 100N L512
330P/100V
C582
KRA107S LA+
4700(M)
M3 PVDD_C
C578 1000N 10uH
C583
51K
47N
R580
M2 OUT_C LA+
H H
R583 R582
C5007 R581 51K
18-F 18-F
M1 DGND_C 1000N LA-
-
C579
C580
PWM_C DGND_D C5008 LA-
C584
330P/100V
1000N
R584
C585
1K
47N
RESET_CD OUT_D
C586 100N L513
C587
PWM_D PVDD_D
C589 33N(20) 10uH
VDD BST_D
C591 100N C592 100N
C588 R585 GVDD_C GVDD_D
1K
TO _PF102
100N
R586 1 R587 R588 C595

C593
100N
C590
100/16
10 10 10000N/25V
C594 L514 L515

10000N/25V BD120 BD120
J J
C596
100/16
K K
L L
GND LINE POWER+ LINE POWER- LINE ANALOG SIGNAL L ANALOG SIGNAL R DIGITAL SIGNAL SUBWOOFER SCH06_AMP_611
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
61
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
MCR611 FRONT
REFERENCE NO.
__FPC1 1 ~ 101
MAIN B`D
B TO _FPC104 B
LED_GREEN
+16V_OLED
+16V_OLED
EL_RW,WR
EL_RESET
+3V3_CPU
LED_RED
LED_RST
REMOTE
H/P_DET
I2C_SDA
+3V3_D1
I2C_SCL
LED_OR
LED_5V
LED_5V
EL_D/C
GND_D
GND_D
GND_D
EL_RD
EL_CS
KEY3
KEY2
KEY1
D7
D5
D3
D6
D1
D4
D2
D0
FPC1
1.0-11-33P
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33
2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32
FRONT
C1
C2
C3
100N-K
10N-K
1N-K
DGND
+3V3_CPU
C LED_GREEN C
LED_RED
POWR LED STATUS
-
LED_OR LED_R LED_G LED_OR
H/P_DET RED L H L DGND H/P_DET
R1
R2
R3
GREEN L L H
BD121T
LED_5V
ORANGE H L L KEY2
NOTHING L L L Q2 Q1 KEY3
KRC102S
WEJ3290W
KRC102S KEY1
DGND
LED1
+16V_OLED
EL_RST
EL_RW
LED_SDA
LED_RST
LED_SCL
EL_RD
EL_DC
EL_CS
R4
+3V3_D1
KEY1
D7
D5
D3
D6
D1
D4
D2
D0
0
L1
R5
0
R6
1K5
CN2
POWER
10N-K
C4
SW1
JK1 R7 R8
H.P-JACK 270 110
KEY1_2
C7 100N-K
C5
C6
100N-K
100N-K
D D
220
C8 100N-K C9 100N-K
H/P
C10 -
120
R10
R11 R12 C11 100N-K
C12 - DGND
C13 10N-K
+3V3_CPU
R9 TO KEY_R
0 0 C14 100N-K
Q3 Q4 RC1
C16 100N-K KRC102S KRC102S
R94EH1A KEY3
C17 100N-K C18 47/16(5*7) OUT
KEY2
GND
TO CP4
C19 100N-K VCC
R19 47 C20 100N-K
BD121T
BD121T
CN1 D1 1SS355
DGND R20 0
L2
L3
MAIN B`D
D2 1SS355
CN3
H/P_R
CH_GND
H/P_L
+16V_OLED
C22 27N-K
E H/P_R +3V3_D1 E
3 2 1
TO KEY_L
KEY2
GND_A AGND C23 100N-K KEY3
-
C24 27N-K IC1
H/P_L CH_GND
TLC59108 C25 C26 47P-J
TO CP5
R28 R29 47/16(5*7) C27 47P-J
CN1 1 20
R26
R27
Rext Vcc +3V3_D1
3P_WIRE
BD221T
0 1K
DGND
R30 22 C28 47P-J
L4
2 A0 SDA 19 LED_SDA
D7
D6
D5
D4
D3
D2
D1
D0
R31 22
3 A1 SCL 18 LED_SCL
TO CP101
R32 22
4 A2 RESET 17 LED_RST
R33 10K
100N-K
C29 1000N-Z
10N-K
C34 100N-K
0
5 A3 GND 16
R34 0 R35 0 C32 47P-J
BD221T
6 OUT0 OUT7 15
L5
R37 -
R38 0 R39 0
C30
C31
7 14
R36
OUT1 OUT6
8 GND GND 13 C33 100N-K C37 100N-K C35 100N-K

DGND
R40 0 R41 0
F 9 OUT2 OUT5 12 F
1M
C46 4700N-K
C47 4700N-K
C45 1000N-Z
D3 UDZ2.7B
100N-K
C39 4700N-K
0
0
0
0
0
C40 10N-K C44 10N-K C42 10N-K
C38
10N-K
1000N-Z
R42 0 R43 0
10/35(5*5)
10 OUT3 OUT4 11
C50 100N-K C51 1N-K C55 1N-K C53 1N-K
C56
R44
R45
R46
R47
R48
R49
LED2
LED3
LED4
LED5
C48
C49
C57
LED6
LED7
LED8
LED9
CH_GND
CH_GND
CH_GND
-
DGND
DGND
DGND
-
W B G O O G B W 10/35(5*5)
C52 100N-K C41 100N-K
0
DGND
0
C43 47/16(5*7) C36 R50 0 DGND DGND CH_GND DGND
EL_RD
EL_DC
EL_CS
EL_RW
EL_RST
47/16(5*7)
R51
R52
LED_VCC
FPC2 CH_GND CH_GND

- 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30
1 3 5 7 9 11 13 15 17 19 21 23 25 27 29
G G
VCI
CL
NC
VSL
VLSS
CLS
D7
D6
D5
D4
D3
D2
BS0
BS1
CS#
VLSS
D/C#
IREF
VDD
RES#
GND_D
GND_D
E,RD#
VDDIO
VCCMH
D1_SDIN
RW#,WR#
D0_SCLK
+16V_OLED
+16V_OLED
TO OLED
H H
J J
K K
L L
GND LINE POWER+ LINE POWER- LINE ANALOG SIGNAL L ANALOG SIGNAL R DIGITAL SIGNAL SUBWOOFER SCH07_FRONT_611
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
62
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
MCR611 TU-INPUT_KEY
REFERENCE NO.
1 ~ 101
B B
__CP1
MAIN B`D TO _CP106
C R53 C62,C63 L6 C
OPT_OUT2
OPT_OUT1
TU_SDA/DI
TU_INT/DO
AIN_CON1
IC2 R54 C65,C66,C71R55 C78 C80 C79 C7
DAB_ON
TU_CLK
TU_RST
R_OUT
L_OUT
TU_CE
EU(DAB)
SPDIF
OPEN 0Ohm OPEN OPEN OPEN OPEN OPEN OPEN
A+5V
A+5V
D+5V
D+5V
WPS
GND
GND
GND
GND
GND
3V3
NA,JP,CN(TUNER) NJM2752 OPEN 10/16 1K 100/16 1U 100N BEAD
CP1
C125Z2-23C
L_OUT CH_GND
GND GND
A_5V
D D
R_OUT
C58 10N-K
TU_INT/DO
OPT_OUT2
OPT_OUT1
TU_SDA/DI
C59 100N-K
DAB_ON
TU_RST
TU_CLK
L6 BD221T
TU_CE
SPDIF
C60 1N-K
CP2
D_5V
3V3
L7 BD221T C125Z1-11
GND CP2
0
IC2 DAB_R
11
L8
0
NJM2752RB2
GND
10
DAB B`D
C62 10/16
R53
C63 10/16 BD221T DAB_L

9 10
9
C65 10/16 C66 10/16
DAB_IN
R54
2
(OLNY EU)
DAB_OUT
8
7
GND
7
6
C71 10/16 R55 1K AIN_CON1 DAB_ON
E
6
5
D+5V
1000N-K
4
RCA_L
RCA_R
D+5V
10/16
10/16
100/16(6.3*11)
-
C79 100N-K
3
TM1
GND
GND
2
-
C78
SPDIF
1
C75
C80
C82
R57 33
R56
TU_INT
TU_RST 8
7 R58 33
TU_SEN
R59 33
TO CP804
6
WPS
R60 33
TU_SDA
5
R61 33
TU_SCLK
4
C89 C90 TU+5V CP3

3
R_OUT
2
100P-J 100P-J R65 100

L_OUT 100N-K
OPT_OUT2
1
F F
470/10(6.3*11)
R67 R71 R67 R68

R68 R72 R69 - GND
C94
100K 100K
DAB 100K 0 OPT_OUT1
C95
GND
R71
R72
TUNER 15K 15K

0
0
3V3
GND
C101 100N-K
0
CP3
C125Z1-05
TO CP812
R73
GND
JK2
INPUT
SW15
L R
CNT1 WPS
(5PIN)
AUX H
TUNER L
G G
KEY B`D
H CP4 H
KEY1_2
OPEN/CLOSE
DGND
TO CN2 KEY3
SW2
KEY2
R16 R17
10K 6K8
CP5
PLAY/PAUSE
C34 100N-K
VOL DOWN
C41 10N-K
J J
SW8
SW7
KEY2
KEY3 C52 1N-K

DGND
CH_GND
DGND
TO CN3 R22 R23 R24 R25
DGND
3K3 2K7 3K9 6K8 - -
SKIP FWD
SKIP REV
VOL UP
STOP
SW11
SW12
SW13
SW14
K R13
CURSOR DOWN
R14 R15
K
CURSOR RIGHT
1K5 1K8 2K7
CURSOR LEFT
CURSOR UP
C15 10N-K
SW3
SW4
SW5
SW6
C36 100N-K
C43 10N-K
R21 C54 1N-K
1K5
CH_GND
C21 10N-K
DGND
ENTER
INPUT
SW10
SW9
L DGND
- - L
GND LINE POWER+ LINE POWER- LINE ANALOG SIGNAL L ANALOG SIGNAL R DIGITAL SIGNAL SUBWOOFER SCH08_INPUT
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
63
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
B B
CD PART
PDIC VCC
PDIC VC
TO CD Pick-up
CN701
C C
C701 0.01
C702 0.1
KTA1504S
Q701 L701 10UH C703 470/10V C809 0.1
R702 39
D701 1SS355
R703 39 GND_DRV
C816 0.1
91
R704 39 C704 0.1 C706 102 C817 0.01 GND
R705 39 C705 470/10V C707 0.1
R701
GND_DRV
C708 0.01
GND_DRV
C818 0.1
AGND C711 0.1
C710 C819 0.01
+1.5V
GND
100/10V C712 0.1
OPEN
IC703 AGND GND
C950
AZ1117-1.5V
D IN OUT
GND_DRV
D
D
B
E
F
PD
100/10V
100/10V
1SS355
G
0.1
0.1
GND_DA
FO+
TR+
FO-
TR-
C716
C715
C714
C713
D705
GND_DA
LD_CHK R706 1K
CD_SPDIF
SDTI R766 OPEN
E BICK
LRCK
C774 0.047u
E
DMO
SBSY C773 OPEN

R765 0 FMO
C772 0.047u
IC702
GND_DA
+1.5V
R764 0 TRO
IP4001CR
0.1
33
33
33
33
0
0
0
0
R763 0 FCO LMSW LMSW
C786 0.1
R718
R717
R716
R715
GND_DRV
C721
C720
C719
0.033u C771
R714
R712
22P
22P
22P
C718
R713
R711
C717 5600P
SLED-
OPEN
R762
SLED+
C770 C784 OPEN
C769
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
24
23
22
21
470P
100/10V SP-
22 23 24 25 26 27 28
PGND2 DO1-
1
C768 C781
FSMoNiT
C767 0.1
VDD1-3
60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41
DVSS3R
9 10 11 12 13 14 15 16 17 18 19 20
SP+
AVDD3
470P
F F
DO4- DO1+
VSS-3
RFRP
FMoS
2
Pio11
Pio10
0.1
RFZi
DMo
PD
FMo
R776 OPEN
Pio9
Pio8
TRo
FCo
TEi
Ro
DO4+ IN1
3
C724 C766 R771 470 R772 R777 470
CN704
DVDD3R LDo FMO DMO
0.1 100/10V IN4 IN1A
4
MDi
OPEN C787 0.1
C725 DVDD3L AVSS3 VRo
Pio12/CDMoN0/FGiN
IN4A N/C
5
100/10V E C788 0.01
C726
Lo TNi C777 REF REO
GND
Pio14/CDMoN2
Pio13/CDMoN1
6
0.1 F 0.1 R778 0
DVSS3L TPi M_MUTE
C778 VCC2 MUTE
GND GND_DRV
7
CDMoN3
B 100/10V
R955
XVSS3
47K
FPi1
D C780
30
29
FIN FIN
Xi FPi2 0.1
A
Xo FNi1
C779
15 16 17 18 19 20 21
VCC1 SGND GND_DRV
8
C727 C765 C 470/16V
IC701
0.1 XVDD3 FNi2 R779 4.7K OPEN
0.1 GND_DRV CTL FWD
14 13 12 11 10 9
C728 C763 TRO R774 47K R780 0 FCO
VDD1-2 RVSS3
OPEN IN3 IN2
0.1
R775 0
TC94A92FG-301
GND_DA VSS-2 RFo TR+ C785 OPEN FO+
DO3+ DO2+
DREQ C762 0.1 C764 C782
Pio0 AGCi TR- 0.1 FO-
G R721
0
R722
1M Pio1 DCoFC
8
7 C761
0.01
C783
DO3- DO2- CLSW
CL_SW G
100
DO5- PGND1
4700P 0.1 R781 4.7K
Pio2 RFEQo CLOSE GND_DRV
6
X701 C760 0.1 DO5+ REV OPSW

16.9344M OP_SW
D+3.3V
Pio3 RFRPi
5
Pio5
R723
Pio4 Pio6 RFi C759 LOAD-

4
PVREF
Pio7 4700P
VCoF
LPFo
SLCo LOAD+
3
MOTOR DRIVE
C758 0.01
/SRAMSTB
RVDD3 A+3.3V
0.1
0.1
2
VDD1-1
VDDM1
2200P
CN705
C756 C755
VSS-1
BUCK
TMAX
C729
VDD3
BUS0
BUS1
BUS2
BUS3
TEST
LPFN
/CCE
/RST
PDo
15P VCoi
100/10V
MS
C730 R761 C757 +8VM
C790
C789
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
61
62
63
64
65
15P
0.1
0.015u
220 C754
R742
GND_DA C731 0.1

0.1
0
R748
330K
C744
C751 GND_DRV
0.1
AGND
0.01
C747
GND_DA
H +1.5V
AGND
H
47K
15K
C745
0.1
R750
R749
C746
10K
R732 10K 1000P

D+3.3V
C748 47P
R733 10K
R743
VC
GND_DA
47/25V
R734 10K
C750
C749
0.1
R735 10K R744 10K

R736 10K R745 10K
C798 0.1
R746 10K AGND
R794 0.1 C799 OPEN

0.1uF -> OPEN change
100
100
100
100
100
33
R795 0.1
IC704
D715 1SS355T R796 0.1
J AZ1117-3.3V
IC705 OUT J
R737
R738
R739
R740
R741
R747
LM7808 C795 0.1 R797 0

IN OUT 4 GND
IN 1 3
C796 0.1 R798 0
VIN VOUT
C734 G C793
0.1 220/16V G2 GND
C797 0.1 R799 0
1SR159
D716
GND_DRV GND_DRV AGND
100/10V
GND_DA
470/16V
1SS355
C737
C736
C792
D711
C791
0.1
C775
0.1
GND
0.1uF -> 0 change
100/10V C794
D718 D717 GND_DRV
1SR159 0.1
1SR159 GND_DRV AGND
GND_DRV
GND_DA
GND_DRV
SRAMSTB
R782 0
DSPRST
BUCK
BUS0
BUS1
BUS2
BUS3
CCE
GND_DA
R783 0
R784 0
DSPRST
LD_CHK
DREQ
BUCK
CD_SPDIF
BUS0
SBSY
SRAMSTB
CCE
BUS3
BUS2
BUS1
GND_DA
K R786 10K
K
CLOSE
M_MUTE
OPEN
OPSW
LMSW
CLSW
GND_DA
R787 10K D+3.3V

R788 10K
R789 10K
1000P
1000P
C743
C738
C741
C740
C739
C742
0.01
0.01
GND_DA R790 10K

0.1
0.1
GND_DA GND_DRV
CN702
GND_DA GND_DRV CN702
CN703
GND
BUS3
BUS2
BUS1
BUS0
CD_CCE
CD SRAMSTB
GND
SPDIF
GND
CD_BUCK
CD_OPSW
CD_CLSW
CD_LMSW
CD_DREQ
CD_SBSY
CD_OPEN
CD_CLOSE
CD_LDCHK
CD_DECRST
CD_M_MUTE
GND
GND
D+5V
+12V_D
GND_DRV
L L
TO FPC102
GND LINE POWER+ LINE POWER- LINE ANALOG SIGNAL L ANALOG SIGNAL R DIGITAL SIGNAL SUBWOOFER SCH09_CD
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
64
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
A A
CN411
DC_LINK T821 D411 L411 C443 L441 CN411
PQ3225 MBRF20200CT 5.6uH +29V +29V 104K 47uH TO CN500 5267-6A
1 (BAR) (1608) (7.3*7.3mm)
1 10 2 +12V_D +29V 1
3
2
R828 R821 C821 C441 C445 C444
1
D801 C805 C823 220K 220K 103J + C411 + C412 C413 C414 4.7uF 104K IC441 D441 22uF 2
D15SB60 + 470uF SW_220V 103K (3225) (3225) 630V HSD411 1000uF 470uF 104K 104K 35V Y5V (1608) TPS54340 SS26 16V Y5V
2
200V JUMPER 630V (MPE) MH3520-30 50V 35V (2012) (2012) (3216) (X7R) SK26 (3216)
2
SW_110V (105') (MPE) 2 (105'_MK) (105') 1 8 R444 3
BOOT SW
1
B JUMPER 56KF B
1
C822 D821 (1608)
~
~
330pF UF4007 4
1KV 9 R446 R449 2 7
VIN GND
2
C806 (3216) 47K 39K
+ 470uF 3 (1608) (1608) 5
-
+29V
200V R411
2
(105') 330 3 6
C824 B821 (3216) Q441 EN COMP
8 6
P_VCC
3
104K (3550) MMBT2222A R445
(2012) HSQ821 C415 2 R450 C450 R442 4KF
2 1
1 2 MH3520-30 102K 5K 104K 4 5 12K (1608)
Q821 1KV (1608) (1608) RT/CLK FB (1608) CN221 CN221
1
3
SMK08N70 4 7 (3216) (NC) R441 C449 20010WS-12
C 1 1 Q442 120K 100pF C
P/S
KRC119S (1608) C442 (1608) P/D 1
3
R822 R823 682K (X7R)
2
8
5
4.7 10K (1608)
D811 (3216) (2012) R447 (X7R) BI_AMP(19V) 2
HV
GATE
NC
VDD
HS1M IC821 5 6 R428 22K
FL6300A +29V 4.7K (1608)
R824 (2012) P/S 3
100
2
(2012)
R813 R826 R421 +12V_A 4
GND
DET
270K 220K 2.2K Q421
CS
FB
+12V_D
1
(3216) +5V C825 R825 (2012) (2012) KN2907AS
D L802 22pF 0.2 5 D
4
CV615280S (2012) 1W
1
D822 C826 PC821 R422 R423 R426 R427 -12V_A 6
1
R272 UZ22B 104K EL817B 1K 53KF 86.6KF 47K R443 R448 C446 C447 C448
PC811 4.7K (2012) PC-17K1 (2012) (2012) (2012) (2012) 1.2K 1.2K 102K 103K 104K
2
EL817B (2012) (3216) (3216) (2012) (2012) (2012) 7
3 2
PC-17K1 (X7R) (X7R) (X7R)
3
R827
3
C803 C804 20K C421 R425 8
P/D +12V_D
SD102M SD102M R271 (2012) IC421 1 473K 1K R424 1 BI_AMP(19V)
AC250V AC250V 1K LR431 (2012) (2012) 5KF
(2012) C827 TL431 (2012) Q422 +5V 9
2
3
E R811 SD102M KRC119S E

470K 2 Q271 AC250V
(3216) MMBT2222A 10
R273 C271
1
10K 224K
R812 (2012) (2012) +20V 11
C802 120K (X7R)
0.1uF
AC275V
(3216) TO _CP10312
T871 D221
2
EE2525(V-13P) HS1G Q221 IC221

(SMA) C3209 KIA79L12 CN222
1 13 1 3 2 3 20010WR-04
F DC_LINK +20V IN OUT -12V_A F
GND
1
1
C877 R871 C871 4
2
333K 150K 103K + C221 R221 C224 C225
2
L801 630V 1W 630V 100uF 10K R222 + 47uF 104K
1
CV615280S (MPE) (MPE) 50V (2012) 3.3K 25V (2012) 3
OPTION TABLE
1
2 (105') (2012) (105')
D222
AC100V HS1G R229 2
AC220V-240V
1
C872 D871 (SMA) 1K
3
330pF HS1M 10 (2012)

SW_110V JUMPER NM 1KV R228 1
2
(3216) 3 C222 R223 2.2K
SW_220V NM JUMPER
3
+ 220uF 6.8K Q222 (2012)
G 470uF/200V NM IC871 35V (2012) A1298 Q224 2 G
R801 C805 ICE3BR1765J 11 (105') MMBT2222A
P/S
1.5M C806 330uF/400V R227 CN224
470uF/200V
1
1/2W (SURGE) 5 4 10K 20010WS-03
DRAIN DRAIN
R812 120K/(3216) NM R872 D223 (2012)
0.68 HS1G Q243 IC222 1
C801 1/2W (SMA) A1281 KIA7812
0.22uF 6 3 4 12 1 3 +12V_A
AC275V N.C CS IN OUT
2
GND
1 2 + C226 + C227 C228
7 2 220uF 47uF 104K 3
VCC FB
t
2
RV801 C875 9 35V R224 25V (2012)
H TH801 14D561 0.22J 5 (105'_WB) 6.2K (105') H
10D13 (2012) (3216)
8 1 1 2 D224 R225 CN225
GND BA SS36 2.2K 20010WR-03
3
7 (SMC) (2012)
Q223 2 P/S 1
MMBT2222A
2
D225 R226
1
R873 SS36 10K 2
F801 P_VCC_IN Q871 P_VCC D874 10 (SMC) (2012)
T5AL 250V KN2907AS BAV21W (3216)
3
1
D226 L221
2
R874 SS36 5.6uH

J D872 + C873 R875 + C878 D873 C874 + D875 10 (SMC) (BAR)
J
CN223
1
UZ22B 33uF 10K 33uF UZ22B 47uF BAV21W (3216) +5V CN223
50V (2012) 50V 50V P_VCC_IN B221 5268-6A
(105') (NC) (105') R241 (3550)
1
470 + C229 + C230 C231 C232 +5V 2 1 1

CN801 (2012) 3300uF 470uF 104K 104K
YW396-03AV +5V 10V 10V (2012) (2012)
(105'_MK) (105') 2
R876
2
47K PC871 R243

1
(2012) D876 C876 EL817B R242 5.3KF R251 R253 R255 3

R877 R879 UZ22B 473K PC-17K1 1K (2012) 0 0 0
K
330 0 (2012) (2012) (2012) (2012) (2012) TO CP805 K
2
(2012) (2012) (X7R) (NC) 4

1
P/S
3
R252 R254 R256

4
PC872 C879 R245 C241 0 0 0 5

PCB EL817B R878 SD102M IC241 1 33K 224K R244 (2012) (2012) (2012)
FR-4(177*93mm) PC-17K1 10K AC250V LR431 (2012) (2012) 5KF
(2012) TL431 (X7R) (2012) 6
3
P C B
L L
: To reduce the risk of electric shock,leakage current or resistance measurement

shall be carried out before the appliance returned to the customer
GND LINE POWER+ LINE POWER- LINE AUDIO SIGNAL TMDS SIGNAL ANALOG VIDEO DIGITAL VIDEO SCH10_SMPS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
65
EXPLODED VIEW
Please see the last chapter for the part list.
S9*4 47
42
31 48
S2*2 43 49
S5*2(U/F/K)
50
S2*3
44 65 53
S2*1"N"ONLY
40 66
45 RD
BK
46 51
BK
70 S4*1 RD
35 S10*2
34
33 52
S7*1
S2*4
32
S7*3
21 S7*1
S7*2 S1*9
41 54
22 S11*4
41 S5*2
S11*4 38 62
24 39
37 S3*2
23
28 69 S2*4
9 10 S7*1
36 S6*4
29
20 55
8 11 19
12 18 S2*12
67 56
7 S9*4
5 6 S2*2
S2*2
4
13
3 64
S11*4
S2*2
2 57
68
31
27 64 58 59
26 60
S8*4
25
57
17
16 58
15 S12*4
67
S7*4
14 68 30
1
S6*6
63
WARNING:
66 Parts marked with this symbol z have critical characteristics.
Use ONLY replacement parts recommended by the manufacturer.
PACKING VIEW
Please see the last chapter for the part list.
* BOX BOTTOM TAPE( O )
38
2
6
NR1501
3
FB
37
Ad
hes
ive
7
1 8
5
39
9
19
32
C
D
13
14
10
8
12 15
11
8
19 MANUAL ASSY(N1W) 32 ANT ASSY(K1B)
18
26
21 35
23
17
20
C
20
D
511
MCR
SE
TF 25
22 RO
24 NT 16
19 MANUAL ASSY(U1B) 19 MANUAL ASSY(FN) 19 MANUAL ASSY(K1B) 32 ANT ASSY(FN)

14 22 26
21 22
23 26 29
29
C
20
D
27 20 20 23 20
23
28
22 31 25
30
25
67
SEMICONDUCTORS
Only major semiconductors are shown, general semiconductors etc. are omitted to list.
The semiconductor which described a detailed drawing in a schematic diagram are omitted to list.
1. IC's
R5F56108VNFP (MAIN : IC112)
68
R5F56108VNFP Terminal Function
STANDBY MODE
Pin Port Name PD/PU I/O TIMER Network OLED OLED+NW Note
STBY
STBY STBY STBY STBY
1 TDI PU I I I I I I Emulator Connection terminal
2 TMS PU I I I I I I Emulator Connection terminal
3 TEST1 PD I I I I I I Boot for Check PCB mode
4 OPEN - O O/L O/L O/L O/L O/L OPEN
5 AVSS - - - - - - - GND
6 TRST# PD I I I I I I Emulator Connection terminal
7 RXD MI232O PU I I I I I I UPDATE
8 TXD MO232I - O O/L O/L O/L O/L O/L UPDATE
9 P.Down PU I I I I I I P.Down Detect（INT）
10 EMLE PD I I I I I I Emulator Connection terminal
11 TDO PU_OPEN O O/L O/L O/L O/L O/L Emulator Connection terminal
12 VSS - - - - - - - GND
13 MDE PD I I I I I I Operation Mode Setting
Smoothing capacitor (0.1uF) connection
14 VCL - I I I I I I
terminal
15 MD1 PU I I I I I I Emulator Connection terminal
16 MD0 PU I I I I I I Emulator Connection terminal
Analog Switch IC Control 1 (AUX1=H,
17 AIN_CNT1 - O O/L O/L O/L O/L O/L
TUNER=L)
19 RESET PU I I I I I I Reset
20 X-OUT - - - - - - - Clock Output (12MHz)
21 VSS - - - - - - - GND
22 X-IN - - - - - - - Clock Input (12MHz)
23 VCC - - - - - - - +3.3V_CPU
24 NMI PU I I I I I I Basic Functions of Microcomputer
25 EL RESET PD O O/L O/L O/L O/H O/H Reset for OLED (L: Reset)
26 EL E,RD - O O/L O/L O/L O O EL Readout
Switching Data/Commando (H : Data, L :
27 EL D/C - O O/L O/L O/L O O
Command)
28 EL R/W,WR - O O/L O/L O/L O O EL Writing
29 EL CS - O O/L O/L O/L O/L O/L EL Chip Select (L : I/F communication)
30 D7 - O O/L O/L I O O Data Bus for OLED
38 TU_SDA PU O O/L O/L O/L O/L O/L I2C Data for TUNER
39 PLLVCC - - - - - - - +3.3V_CPU
40 TU_INT - I I I I I I TUNER Interrupt
41 PLLVSS - - - - - - - GND
42 TU_SCL PU O O/L O/L O/L O/L O/L I2C Clock for TUNER
43 E_REQ PD I I I I I I DM870 Interrupt
44 GD25Q32_CLK - O O/L O/L O/L O/L O/L GD25Q32-6P, CLK
45 GD25Q32_SI PU I/O I I I I I GD25Q32-5P,SI ( IO0 )
46 GD25Q32_SO PU I/O I I I I I GD25Q32-2P,SO ( IO1 )
47 GD25Q32_CS - O O/L O/L O/L O/L O/L GD25Q32-1P, CS
48 EEPROM SDA PU I/O I I I I I EEPROM R1EX24256A Control
49 EEPROM SCL PU O I I I I I EEPROM R1EX24256A Control
50 OLED_P_CONT PD O O/L O/L O/L O/H O/H Power Control for OLED +18V
51 GD25Q32_WP PU I/O I I I I I GD25Q32-3P,WP# ( IO2 )
52 /E_SPICS PU(CX870) O O/L O/L O O/L O SCI or CS Signal Output to the DM870
53 GD25Q32_HOLD PU I/O I I I I I GD25Q32-7P,HOLD# ( IO3 )
55 E_RESET PU(CX870) O O/L O/L O/H O/L O/H Reset for DM870
56 OLED_3V3_CONT PD O O/L O/L O/L O/L O/L OLED_3.3V_CONT
57 VSS - - - - - - - GND
59 VCC - - - - - - - +3.3V_CPU
60 TU_CE - O O/L O/L O/L O/L O/L Tuner Control (CE)
61 TU_RST PU O O/L O/L O/L O/L O/L Reset Tuner
69
STANDBY MODE
STBY
STBY STBY STBY STBY
62 SP_PROTECT PU I I I I I I DC Power Detect (SPK OUT)
+1V2_NET_P_
63 PD O O/L O/L O/H O/L O/H Power Control for CY920_+1.2V
CONT
PD(DIR_
67 DIR_INT RERR) I I I I I I PCM9211(DIR) Control
Common
68 DIR_RST PD O O/L O/L O/L O/L O/L PCM9211(DIR) Control
69 E_SPIMOEI - O O/L O/L O/L O/L O/L CY920 SPI
70 E_SPIMIEO - I I I I I I CY920 SPI
71 E_SPICLK - O O/L O/L O/L O/L O/L CY920 SPI
Analog Input Detection from PCM9211 (Not
72 DIR_INT1 PD I I I I I I
used)
73 /H/P_MUTE PD O O/L O/L O/L O/L O/L H/P MUTE
74 VCC - - - - - - - +3.3V_CPU
75 SW_MUTE PD O O/L O/L O/L O/L O/L SW MUTE
76 VSS - - - - - - - GND
77 /5558_RESET PU O O/L O/L O/L O/L O/L TAS 5558 System Reset input (11 pin)
TAS 5558 Headphone in/out selector (12
78 /H/P_ON PU O O/L O/L O/L O/L O/L
pin)
79 /5558_PDN PU(DTA) O O/L O/L O/L O/L O/L TAS 5558 Power down (12 pin)
80 /5558_MUTE PU(DTA) O O/L O/L O/L O/L O/L TAS 5558 Soft mute of outputs (14 pin)
82 5558_SDA PU I/O I I I I I TAS 5558 I2C SDA (24 pin)
83 5558_SCL PU I/O I I I I I TAS 5558 I2C SCL (25 pin)
84 /5142_SD PU I I I I I I TAS 5142 Shutdown Signal
85 /5142_OTW PU I I I I I I TAS 5142 Overtemperature Warning Signal
86 DIR_DO - I I I I I I PCM9211(DIR) Control
87 DIR_DI - O O/L O/L O/L O/L O/L PCM9211(DIR) Control
88 DIR_CL - O O/L O/L O/L O/L O/L PCM9211(DIR) Control
89 DIR_CE - O O/L O/L O/L O/L O/L PCM9211(DIR) Control
90 DIR_RERR PD I I I I I I PCM9211(DIR) Control
91 VCC - - - - - - - +3.3V_CPU
93 VSS - - - - - - - GND
+3V3_NET_P_
CONT
+2V5_NET_P_
CONT
+1V8_NET_P_
CONT
Mute Control When Switching USB Route
97 USB_OE - O O/L O/L O/L O/L O/L
(H：MUTE / L：Enable)
98 AUDIO_P_CONT PD O O/L O/L O/L O/L O/L Power Control (-/+3.3V_D1, -/+12V_A)
99 +5V_P_CONT PD O O/L O/L O/H O/L O/H Power Control for CY920_+5V
100 HP/DET PU I I I I I I H/P detect
101 FRONT_USB_SW PD O O/L O/L O/L O/L O/L Front USB Switch IC Control
102 NFC_ACK PU I I I I I I Bluetooth Pairing Mode
103 iOS_ACK PU I I I I I I WiFi Sharing Start
104 WPS_ACK PU I I I I I I WPS Start
105 SRAMSTB PU O O/L O/L O/L O/L O/L SRAMSTB Control for CD DSP
106 BUS3 PU I/O O/L O/L O/L O/L O/L CD DSP (TC94A92FG) Control
110 CCE PU O O/L O/L O/L O/L O/L CD DSP Control (Chip Enable)
111 BUCK PU O O/L O/L O/L O/L O/L CD DSP Control (BUS CLK)
112 OPSW PU I I I I I I Open SW from CD Mecha
113 CLSW PU I I I I I I Close SW from CD Mecha
114 LNSW PU I I I I I I Limit SW from CD Mecha
115 DECRST PU O O/L O/L O/L O/L O/L Reset for CD DSP (TC94A92FG)
116 DREQ - I I I I I I CD DSP (TC94A92FG) DREQ
CD Monitor (Default: SBSY) from CD DSP
117 SBSY PU I I I I I I
(TC94A92FG)
70
STANDBY MODE
STBY
STBY STBY STBY STBY
118 DRVMUTE PU_OPEN O O/L O/L O/L O/L O/L CD Driver Mute (H: Mute Off, L: Mute On)
119 CD_OPEN - O O/L O/L O/L O/L O/L Open CD Tray
120 CD_CLOSE - O O/L O/L O/L O/L O/L Close CD Tray
121 VBUS_FLUG1 PU I I I I I I Check VBUS Voltage 1 (Front USB), L : Error
123 LD_CHK AD I I I I I I Check CD Laser Diode Current
124 VBUS_CTL1 PD O O/L O/L O/L O/L O/L VBUS Control 1 (Front USB)
SMPS_BURST_
125 - O O/L O/L O/L O/L O/L SMPS Burst mode Control
CONT
126 DM_VBUS_CONT - O O/L O/L O/H O/L O/H DM870 VBUS Control
128 LED_ORANGE PD O O/L O/H O/L O/L O/L Control ORANGE (Red + Green) LED
129 LED_RED PD O O/L O/L O/H O/L O/H Control RED LED
130 VSS - - - - - - - GND
131 LED_WT PD O O/L O/L O/L O/L O/L Control WHITE LED (POWER ON: H)
132 VCC - - - - - - - +3.3V_CPU
133 MODEL AD I I I I I I Model Select (L (0V):N4, H (3.3V):N9)
134 REGION AD I I I I I I Region Select (H (3.3V):E2, E3/MID (1.64V):JP)
135 DC_PROT1 PU I I I I I I Power Down Detect (+29V LINE)
136 DC_PROT2 PU I I I I I I Power Down Detect
137 REMOTE IN PU(open) I I I I I I Remote Input
138 KEY3 PU I I I I I I Key Input 3 (A/D Port)
140 VREFL - - - - - - - GND
142 VREFH - - - - - - - +3.3V_CPU
143 AVCC - - - - - - - +3.3V_CPU
144 TCK PU I I I I I I Emulator Connection terminal
71
Pin Layout (Top View)
TC94A92FG (CD : IC701)
DVDD3R
DVDD3L
DVSS3R
DVSS3L
VDD1-2
XVDD3
XVSS3
VSS-2
Pio7
Pio6
Pio5
Pio4
Pio3
Pio2
Pio1
Pio0
Ro
Xo
Lo
Xi
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
VDD3 61 40 CDMoN3
BUS0 62 39 Pio14/CDMoN2
BUS1 63 38 Pio13/CDMoN1
BUS2 64 37 Pio12/CDMoN0/FGiN
BUS3 65 36 Pio11
BUCK 66 35 Pio10
/CCE 67 34 Pio9
MS 68 TC94A92FG 33 Pio8
/RST 69 32 VDD1-3
TEST 70 (Top View) 31 DMo
VDD1-1 71 30 FMoS
VSS-1 72 29 FMo
/SRAMSTB 73 28 VSS-3
VDDM1 74 27 TRo
PDo 75 26 Foo
TMAX 76 25 AVDD3
LPFN 77 24 TEi
LPFo 78 23 RFRP
PVREF 79 22 RFZi
VCoF 80 21 FSMoNiT
TC94A92FG
10
11
12
13
14
15
16
17
18
19
20
1
2
3
4
5
6
7
8
9
VCoi
RFi
RFRPi
AGCi
TPi
TNi
MDi
DCoFC
RVDD3
RVSS3
FNi2
FNi1
FPi2
FPi1
SLCo
RFo
AVSS3
VRo
LDo
RFEQo
Block Diagram
TC94A92FG Block Diagram
BUCK / CLK / SCL

BUS3 / Si / SDA
BUS0 / Pio15
BUS1 / MS2
/SRAMSTB
BUS2 / So
VDDM1
PVREF
TMAX
VDD1
VDD3
/CCE
VCoF
TEST
LPFN
VSS1
/RST
LPFo
VCoi
PDo
MS
SRAM SRAM
- 512kbit 512kbit MCU I/F
SLCo PLL For
(4kw*128bit) (4kw*128bit) Resume
DSP-VCO
slicer
+ DSP
EFM
RFi VCO TMAX

PVREF PVREF I2C
SRAM I/F
RVDD3
RVSS3
Intrupt
IRQ
Cont.
Synchronous
RF Ripple Subcode
RFRPi DET.(RFRP)
guarantee EFM
decoder
3 2009-05-27
decoder
RFRP
round & limit round & limit Instruction

Auto Gain Decoder
AGCi Pio7
Cont.(AGC)
Pio0-7
40bit Pio6
General I/O
IO_CTR
/ATT
DCoFC 1024w Pio5

RF-EQ 4KB SRAM
IP
A3 A2 A1 A0
I/F
(40bit)
RFEQo Pio4
DC level ALU MAC PRAM Pio3
DET(RFDC) AY AX MZ MY MX 4kw*9=36kw Pio2
(40bit)
Correction
Pio1
Address
RFo PROM
RFDC
Error
register Pio0
X0/X1/X2 Program
FNi2 RF Y0/Y1/Y2 Control
FNi1 Y-Bus
Focus Bus
FEI X-Bus Switch
FPi2 Error
(FE)
servo
CLV
C-Pointer Y-Pointer X-Pointer

FPi1
Automatic adjustment
register register register 4kw*11=44kw 4kw 4kw 4kw

Digital equalizer
(24bit) (24bit) (24bit) (24bit)

circuit
Address Calc. CROM ERAM YRAM XRAM

Bias circuit 2sets
VREF
PVREF RESiN
Reference
Control
Servo
Voltage
VRo gene.(VRO)
ROM
RAM
Reference CD monitor General I/O

Service Manual: U1B/N1B/K1B /FN

Uploaded by

Copyright:

Available Formats

Service Manual: U1B/N1B/K1B /FN

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: U1B/N1B/K1B /FN

Uploaded by

Copyright:

Available Formats

Service M-CR611 /U1B/N1B/K1B

Manual NETWORK CD RECEIVER

Copyright 2016 D&M Holdings Inc. All rights reserved.

ABOUT THIS MANUAL.................................................................3 PROCEDURE AFTER REPLACING

What you can do with this manual

Search for a Ref. No. (phrase) Jump to the target of a schematic

You can use the search function in Acrobat Reader to

1.Press Ctrl+Shift+F on the keyboard.

2.Enter the Ref. No. you want to search for in the

•Page magnification stays the same as before the

3.Click an item on the list.

Add notes to this data (Sign) Magnify schematic / printed circuit

• When you want to move the area shown, hold

[Example using Adobe Reader 9]

Print a magnified part of the manual

2. On the "File" menu, click "Print".

3. Configure the following settings in the Print dialog box.

4. Click the Print button to start printing.

• The Loupe Tool window appears on the screen.

[Example using Adobe Reader 9] [Example using Adobe Reader 9]

NOTE FOR PARTS LIST

INSTRUCTIONS FOR HANDLING SEMI-CONDUCTORS AND OPTICAL UNIT

1. Ground for Human Body

2. Ground for Workbench

<Incorrect> <Correct> Grounding Band

All ICs and many other semi-conductors are

F ATTENTION D WARNUNG AVVERTIMENTO

USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURE OTHER THAN THOSE

AVOID DIRECT EXPOSURE TO BEAM

WARNING LOCATION: INSIDE ON LASER COVERSHIELD

Replacing the WLAN MODULE with a new one

FRONT PANEL ASSY TUNER

2. FRONT PANEL ASSY

View from the bottom

View from the CD MECHA bottom

(2) Remove the screws.

View from the bottom

From R side From L side

4. MECHA SUPPORT L/R

↑Shooting direction: D↑ ↑Shooting direction: A↑

9. MAIN PCB ASSY

2. Precautions when handling the laser CD mechanism

3. Cautions on assembling and adjustment

4. Determining whether the laser pick-up is defective

Protective soldering place for laser diode.

Initialization Items (Default setting)

3.2. Version display

3.3. Display Order

Select "Version" in the "Setup".

The version of the System u-com is displayed.

The version of the boot loader System u-com is displayed.

The version of the boot loader Network u-com is displayed.

The version of the image Network u-com is displayed.

When Network Module CY920 startup is incomplete

MZ_：Fixed characters・b：Last digit of year・cc：Week number・dddddd：Serial number

Displays the Bluetooth Mac Address

CD TEST MODE indicator (when disc is loaded)

4.2. Before starting the test

4.3. Servo check

•Page magnification stays the same as before the

• When you want to move the area shown, hold