NT10

TRANSFORMER PROTECTION RELAY

RESTRAINED DIFFERENTIAL
FOR TWO WINDINGS TRANSFORMERS WITH OVERCURRENT
ELEMENTS AND THERMAL IMAGE

— Application
The NT10 relay is suitable for two windings MV, LV power transformers.
The adjustment of amplitude and phase current differential protection can be achieved through internal compen-
sation (sw) or through the use of external adapters.

NT10

74CT 37 46 49 50/51
- Protective & control functions
BF
52
37 Phase undercurrent
74TCS 46 Negative-sequence overcurrent
49 Thermal image
50/51 Phase overcurrent
50N.1/51N.1 87NHIZ 64REF 50N/51N
50N/51N Residual overcurrent
64REF Biased restricted differential ground fault
side H I2/I1 Phase interruption under low-load condition
87T
side L 87NHIZ High impedance restricted ground fault
87T Double slope biased differential for two
windings transformers
50N.2/51N.2 87NHIZ 64REF 50N/51N
BF Breaker Failure
74CT CTs monitoring
74TCS Trip circuit supervision

74TCS BF

74CT 37 46 49 50/51

Control functions COMMUNICATION

- RS232
METERING
- I L1..I L3,I E - Modbus RS485
- Oscillography - Modbus TCP/IP
- IEC 870-5-103/DNP3
- Events & Faults log

NT10 - Flyer- 08 - 2012

— Firmware updating — Differential protection for two-windings transformer
The use of flash memory units allows on-site firmware updating. In order to correct any polarity reversals or phase cyclic se-
quence, equal amplitude and phase currents on the two sides of
— Construction differential protection and to clearing the zero sequence compo-
According to the hardware configurations, the protection relay nent, the relay performs the compensation of amplitude, polarity,
can be shipped in various case styles depending on the required to phase and cyclic sequence and zero sequence currents.
mounting options (flush, projecting mounting, rack or with sepa- In the case of internal compensation, the compensation is cal-
rate operator panel). culated by the relay as follows:
• Calculation of the rated currents of the transformer sides from
— Modular design rated power and voltages
In order to extend I/O capability, the NT10 hardware can be cus- • Calculation of the difference (mismatching) between the CT
tomized through external auxiliary modules: primary rated current and rated current of the sides of the
• MRI - Output relays and LEDs transformer
• MID16 - Binary inputs • Choosing the side of the transformer (RefSide) that compensa-
• MCI - 4...20 mA converter tions in current amplitude are related.
• MPT - Pt100 probe inputs. The polarity compensation (Polarity matching) allows us to con-
sider each input current with its angular phase or with opposite
— Measuring inputs phase angle, thus allowing the correction of any reverse polarity
• Three phase current inputs for the H side sw amperometric due to link errors.
• Three phase current inputs for the L side The phase compensation and cyclic sequence and zero se-
• Two residual current inputs for the H side or the L side quence allows the sw correction of the currents displacement
For all inputs the rated currents are independently selectable to on the sides of the transformer due to the vectorial group, any
1 A or 5 A through DIP-switches. phases reversal cyclic sequence and the elimination of any zero
sequence components that may occur on some side due to the
— Binary inputs windings connecting and its ground connection when ground
Two binary inputs are available with programmable active state fault outside the zone of differential protection arises.
(active-ON/active-OFF) and programmable timer (active to
OFF/ON or ON/OFF transitions). — Two set point profiles (A,B)
Two independent groups of settings are provided. Switching from
— Output relays profiles may be operated by means of MMI, binary input and com-
Six output relays are available (two changeover, three make and munication.
one break contacts); each relay may be individually programmed
as normal state (normally energized, de-energized or pulse) and — MMI (Man Machine Interface)
reset mode (manual or automatic). The user interface comprises a membrane keyboard, a backlight
A programmable timer is provided for each relay (minimum pulse LCD alphanumeric display and eight LEDs.
width). The user may program the function of each relay in ac- The green ON LED indicates auxiliary power supply and self di-
cordance with a matrix (tripping matrix) structure. agnostics, two LEDs are dedicated to the Start and Trip (yellow
for Start, red for Trip) and five red LEDs are user assignable.
— Metering
NT10 provides metering values for phase and residual currents,
making them available for reading on a display or to communica-
tion interfaces.
Input signals are sampled 16 times per period and the RMS value
of the fundamental component is measured using the DFT (Dis-
crete Fourier Transform) algorithm and digital filtering.
With DFT the RMS value of 2nd and 5th harmonic of differential
phase current are also measured.
On the base of the direct measurements, the calculated residual
current, the stabilization currents, the sequence currents, the
thermal image, the differential phase currents, minimum-peak-
fixed-rolling demand, mean-minimum-maximum absolute phase
currents are processed.
The measured signals can be displayed with reference to nomi-
nal values or directly expressed in amperes.

Id

Id1=(K2/100) ∙ IS -Q

Id>>

TRIP Id1=(K1/100) ∙ IS

NO TRIP
Id>
α1 α2
0 Is

-Q

2 NT10 - Flyer- 08 - 2012

— Control and monitoring Cold Load Pickup (CLP)
Several predefined functions are implemented: The Cold Load Pickup feature can operate in two following
• Circuit Breaker commands and diagnostic. modes:
• Activation of two set point profiles. • Each protective element can be blocked for a adjustable time.
• Phase CTs monitoring (74CT). • Each threshold can be increased for a programmable time.
• Logic selectivity. It is triggered by the circuit breaker closing.
• Cold load pickup (CLP) with block or setting change.
• Trip circuit supervision (74TCS). — Self diagnostics
• Harmonic restraint. All hardware and software functions are repeatedly checked
• Remote tripping. and any anomalies reported via display messages, communica-
User defined logic may be customized according to IEC 61131-3 tion interfaces, LEDs and output relays.
standard protocol (PLC). Anomalies may refer to:
• Hw faults (auxiliary power supply, output relay coil interrup-
Circuit Breaker commands and diagnostic tions, MMI board...).
Several diagnostic, monitoring and control functions are provided: • Sw faults (boot and run time tests for data base, EEPROM
• Health thresholds can be set; when the accumulated duty memory checksum failure, data BUS,...).
(ΣI or ΣI2t), the number of operations or the opening time ex- • Pilot wire faults (break or short in the wire).
ceeds the threshold an alarm is activated. • Circuit breaker faults.
• Breaker failure (BF); breaker status is monitored by means
52a-52b and/or through line current measurements.
— Communication
Multiple communication interfaces are implemented:
• Trip Circuit Supervision (74TCS).
• One RS232 local communication front-end interface for com-
• Breaker control; opening and closing commands can be car-
munication with ThySetter setup software
ried out locally or remotely.
• Two back-end interfaces for communication with remote mon-
Harmonic restraint itoring and control systems by:
To prevent unwanted tripping of the protective functions on - RS485 port - ModBus® RTU, IEC 60870-5-103 or DNP3 protocol,
transformer inrush current, the protective elements can be - Ethernet port (RJ45 or optical fiber) - ModBus/TCP or IEC61850
blocked when the ratio between the second and/or the fifth har- protocol.
monic differential currents and the relative fundamental current
is larger than a user programmable threshold. — Blocking input/outputs
The function can also be programmed to switch an output relay One output blocking circuit and one input blocking circuit are
so as to cause a blocking protection relays lacking in second provided.
harmonic restraint. The output blocking circuits of one or several Pro_N relays,
shunted together, must be connected to the input blocking cir-
Virtual I/O cuit of the protection relay, which is installed upwards in the
Through ThySetter and ThyVisor tools the type of operation and electric plant. The output circuit works as a simple contact,
links between eight outputs (Virtual Output - VOUT1 ... 8) and whose condition is detected by the input circuit of the upwards
ten virtual inputs (Virtual Inputs - VIN1 ... VIN10) may be defined protection relay. For long distances, when high insulation and
using RPC or IEC 61850 communication protocols over Ethernet high EMC immunity is essential, a suitable pilot wire to fiber optic
network. converter (BFO) is available.
The system allows:
• Availability of eight inputs and ten outputs independently pro- — Event storage
grammable by the user Several useful data are stored for diagnostic purpose; the events
• Simplify wiring using one channel as the Ethernet are stored into a non volatile memory.
• Eliminate the need to install communication devices and / or They are graded from the newest to the older after the “Events
external conversion reading” command (ThySetter) is issued:
• Significantly reduce costs • Sequence of Event Recorder (SER)
• Dynamically change from sw connections and associated The event recorder runs continuously capturing in circular
functions. mode the last three hundred events upon trigger of binary in-
The virtual I / O can be usefully employed for: put/output.
• Transmit information between protections installed in dis- • Sequence of Fault Recorder (SFR)
tance The fault recorder runs continuously capturing in circular
• Achieve accelerated logic discrimination in which some pro- mode the last twenty faults upon trigger of binary input/output
tection elements can be blocked by the activation of the down- and/or element pickup (start-trip).
stream protection start • Trip counters
• Circuit Breaker commands, Selection of setting profiles, Re-
mote trip, etc... — Digital Fault Recorder (Oscillography)
Logic selectivity Upon trigger of tripping/starting of each function or external sig-
With the aim of providing a fast selective protection system nals, the relay records in COMTRADE format:
some protective functions may be blocked. • Oscillography with instantaneous values for transient analysis.
The selectivity logic may be accomplished by: • RMS values for long time periods analysis.
• input and output block circuits, • Logic states (binary inputs and output relays).
• output relays and logic inputs,
• virtual input and output with messages on Ethernet network. — Programming and settings
To guarantee maximum fail-safety, the relay performs a run time All relay programming and adjustment operations may be per-
monitoring for pilot wire continuity and pilot wire shorting. Ex- formed through MMI (Keyboard and display) or using a Personal
actly the output blocking circuit periodically produces a pulse, Computer with the aid of the ThySetter software.
with small width in order to be ignored as an effective blocking The same PC setup software is required to set, monitor and con-
signal by the input blocking circuit of the upstream protection, figure all Pro_N devices.
but suitable to prove continuity of the pilot wire. Full access to the available data is provided:
Furthermore a permanent activation (or better, with a duration • Read status and measures.
longer than a preset time) of the blocking signal is identified, as • Read/edit settings (on-line or off-line edit).
a warning for a possible short circuit in the pilot wire or in the Two session level (User or Administrator) with password for sen-
output circuit of the downstream protection. sible data access are provided.

NT10 - Flyer- 08 - 2012 3

 SPECIF ICAT IONS
GENERAL INPUT CIRCUITS
— Mechanical data — Auxiliary power supply Uaux
Mounting: flush, projecting, rack or separated operator panel Nominal value (range) 24...48 Vac/dc, 115...230 Vac/110...220 Vdc
Mass (flush mounting case) 2.0 kg Operative range (each one of the above nominal values) 19...60 Vac/dc
85...265 Vac/75...300 Vdc
— Insulation tests Power consumption:
Reference standards EN 60255-5 • Maximum (energized relays, Ethernet TX) 10 W (20 VA)
High voltage test 50Hz 2 kV 60 s • Maximum (energized relays, Ethernet FX) 15 W (25 VA)
Impulse voltage withstand (1.2/50 μs) 5 kV
Insulation resistance >100 MΩ — Phase current inputs - sides H and L
Nominal current In 1 A or 5 A selectable by DIP Switches
— Voltage dip and interruption Permanent overload 25 A
Reference standards EN 61000-4-29 Thermal overload (1s) 500 A
Rated consumption (for any phase) ≤ 0.002 VA (In = 1 A)
— EMC tests for interference immunity ≤ 0.04 VA (In = 5 A)
1 MHz damped oscillatory wave EN 60255-22-1 1 kV-2.5 kV — Residual current inputs - IE1 and IE2
Electrostatic discharge EN 60255-22-2 8 kV Nominal current IEn 1 A or 5 A selectable by DIP Switch
Fast transient burst (5/50 ns) EN 60255-22-4 4 kV Permanent overload 25 A
Conducted radio-frequency fields EN 60255-22-6 10 V Thermal overload (1s) 500 A
Radiated radio-frequency fields EN 60255-4-3 10 V/m Rated consumption ≤ 0.006 VA (IEn = 1 A), ≤ 0.012 VA (IEn = 5 A)
High energy pulse EN 61000-4-5 2 kV
Magnetic field 50 Hz EN 61000-4-8 1 kA/m — Binary inputs
Damped oscillatory wave EN 61000-4-12 2.5 kV Quantity 2
Ring wave EN 61000-4-12 2 kV Type dry inputs
Conducted common mode (0...150 kHz) EN 61000-4-16 10 V Max permissible voltage 19...265 Vac/19...300 Vdc
Max consumption, energized
— Emission 3 mA
Reference standards EN 61000-6-4 (ex EN 50081-2) — Block input (Logic selectivity)
Conducted emission 0.15...30 MHz Class A Quantity 1
Radiated emission 30...1000 MHz Class A Type polarized wet input (powered by internal isolated supply)
Max consumption, energized 5 mA
— Climatic tests
Reference standards IEC 60068-x, ENEL R CLI 01, CEI 50 OUTPUT CIRCUITS
— Mechanical tests — Output relays K1...K6
Reference standards EN 60255-21-1, 21-2, 21-3 Quantity 6
• Type of contacts K1, K2 changeover (SPDT, type C)
— Safety requirements • Type of contacts K3, K4, K5 make (SPST-NO, type A)
Reference standards EN 61010-1 • Type of contacts K6 break (SPST-NC, type B)
Pollution degree 3 Nominal current 8A
Reference voltage 250 V Nominal voltage/max switching voltage 250 Vac/400 Vac
Overvoltage III Breaking capacity:
Pulse voltage 5 kV • Direct current (L/R = 40 ms) 50 W
Reference standards EN 60529 • Alternating current (λ = 0,4) 1250 VA
Protection degree: Make 1000 W/VA
• Front side IP52 Short duration current (0,5 s) 30 A
• Rear side, connection terminals IP20
— Block output (Logic selectivity)
— Environmental conditions Quantity 1
Ambient temperature -25...+70 °C Type optocoupler
Storage temperature -40...+85 °C
Relative humidity 10...95 % — LEDs
Atmospheric pressure 70...110 kPa Quantity 8
• ON/fail (green) 1
— Certifications • Start (yellow) 1
Product standard for measuring relays EN 50263 • Trip (red) 1
CE conformity • Allocatable (red) 5
• EMC Directive 2004/108/EC
• Low Voltage Directive 2006/95/EC GENERAL SETTINGS
Type tests IEC 60255-6
— Rated values
COMMUNICATION INTERFACES Relay nominal frequency (f n) 50, 60 Hz
Relay phase nominal current - sides H and L (InH, InL ) 1 A, 5 A
Local PC RS232 19200 bps Phase CT nominal primary current (InpH, InpL ) 1 A...50 kA
Network: Relay residual nominal current (IEn1, IEn2 ) 1 A, 5 A
• RS485 1200...57600 bps Residual CT nominal primary current (IEn1p, IEn2p) 1 A...50 kA
• Ethernet 100BaseT 100 Mbps Primary nominal current choised as reference (Inref ) [1] -A
Protocol ModBus® RTU/IEC 60870-5-103/DNP3, TCP/IP, Side reference for compensation (Refside) [1] - (H)
IEC61850 Current matching type (Matchtype)
INTERNAL/EXTERNAL
Note 1 - Calculated by the relay

4 NT10 - Flyer- 08 - 2012

— Transformer data I2H>> Element
Transformer nominal power (Snt ) 0.01...1000 MVA • I2HCLP >> Activation time (t 2HCLP>>) 0.00...100.0 s
Transformer nominal voltage side H (VntH) 0.200...500 kV • I2H>> Reset time delay (t 2H >> RES) 0.00...100.0 s
Transformer nominal current side H (IntH) [1] - Definite time
Transformer mismatching factor side H (mH) [1] - • 46 Second threshold definite time (I2H >> def ) 0.100...40.00 InH
Transformer base current side H (IBH) [1] - InH • I2H >> def within CLP (I2HCLP>>def ) 0.100...40.00 InH
Transformer grounding side H (GndH) In/Out • I2H >> def Operating time (t 2H >> def ) 0.03...10.00 s
Transformer connection side H (ConnH) Y/D/Z
Transformer vector group side H (VectGroupH) 0 — Negative sequence - 46 side L
Transformer nominal voltage side L (VntL ) 0.200...500 kV I2L> Element
Transformer nominal current side L (IntL ) [1] - • I2L> Curve type DEFINITE
Transformer mismatching factor side L (mL ) [1] - IEC/BS A, B, C - ANSI/IEEE MI, VI, EI, I2t or EM
Transformer base current side L (IBL ) [1] - InL • I2LCLP > Activation time (t 2LCLP>) 0.00...100.0 s
Transformer grounding side L (GndL ) In/Out • I2L> Reset time delay (t 2L > RES) 0.00...100.0 s
Transformer connection side L (ConnL ) y/d/z Definite time
Transformer vector group side L (VectGroupL ) 0-1-2...11 • 46 First threshold definite time (I2L > def ) 0.100...10.00 InL
Note 1 - Calculated by the relay • I2L > def within CLP (I2LCLP>def ) 0.100...10.00 InL
• I2L > def Operating time (t 2L > def ) 0.03...200 s
— Binary input timers Inverse time
ON delay time (IN1 tON, IN2 tON,...IN5 tON) 0.00...100.0 s • 46 First threshold inverse time (I2L >inv) 0.100...10.00 InL
OFF delay time (IN1 tOFF, IN2 tOFF,...IN5 tOFF) 0.00...100.0 s • I2L >inv within CLP (I2LCLP>inv) 0.100...10.00 InL
Logic Active-ON/Active-OFF • I2L >inv Operating time (t 2L >inv) 0.02...60.0 s
I2L>> Element
— Relay output timers • I2LCLP >> Activation time (t 2LCLP>>) 0.00...100.0 s
Minimum pulse width (t TR) 0.000...0.500 s • I2L>> Reset time delay (t 2L >> RES) 0.00...100.0 s
Definite time
— Input sequence • 46 Second threshold definite time (I2L >> def ) 0.100...40.00 InL
Phase current sequence side H (I-SequenceH) • I2L >> def within CLP (I2LCLP>>def ) 0.100...40.00 InL
IL1-IL2-IL3, IL1-IL3-IL2.... • I2L >> def Operating time (t 2L >> def ) 0.03...10.00 s
Phase current sequence side L (I-SequenceL)
IL1-IL2-IL3, IL1-IL3-IL2.... — Negative sequence current / positive sequence current
— Polarity ratio - I2 /I1 side H
C09-C10 (IL1H) NORMAL/REVERSE (I2H /I1H)> Element
C11-C12 (IL21H) NORMAL/REVERSE • (I2H /I1H)CLP> Activation time (t 21HCLP>) 0.00...100.0 s
C...- C... (I..) NORMAL/REVERSE Definite time
C07-C08 (IE2) NORMAL/REVERSE • I2H /I1H First threshold definite time (I21H >def) 0.10...1.00
• (I2H /I1H)>def within CLP (I21HCLP>) 0.10...1.00
PROTECTIVE FUNCTIONS • (I2H /I1H)> Operating time (t 21H>def) 0.04...15000 s
— Thermal protection with RTD thermometric probes - 26 — Negative sequence current / positive sequence current
Alarm
• Alarm threshold θALx (x=1...8) 0...200 °C ratio - I2 /I1 side L
• Operating time t θALx (x=1...8) 0....100 s (I2L /I1L )> Element
• (I2L /I1L )CLP> Activation time (t 21LCLP>) 0.00...100.0 s
Trip Definite time
• Trip threshold θ>x (x=1...8) 0...200 °C • I2L /I1L First threshold definite time (I21L >def) 0.10...1.00
• Operating time t θ >x (x=1...8) 0....100 s • (I2L /I1L )>def within CLP (I21LCLP>) 0.10...1.00
Note: The element becomes available when the MPT module is enabled and • (I2H /I1H)> Operating time (t 21H>def) 0.04...15000 s
connected to Thybus
— Thermal image - 49 side H
— Undercurrent - 37 side H Common configuration:
IH< Element • Initial thermal image ΔθINH (D thINH ) 0.0...1.0 ΔθBH
• 37 Operating logic (Logic37H) AND/OR • Reduction factor at inrush (KINRH) 1.0...3.0
• 37 First threshold definite time (IH <def ) 0.10...1.00 I nH • Thermal time constant τ (TH) 1...200 min
• IH < Operating time (t IH <def ) 0.04...200 s • DthCLPH Activation time (t DthCLPH) 0.00...100.0 s
DtHAL1H Element
— Undercurrent - 37 side L • 49 First alarm threshold ΔθAL1H (D thAL1H) 0.3...1.0 ΔθBH
IL< Element DtHAL2H Element
• 37 Operating logic (Logic37L ) AND/OR • 49 Second alarm threshold ΔθAL2H (D thAL 2H) 0.5...1.2 ΔθBH
• 37 First threshold definite time (IL<def ) 0.10...1.00 I nL Dth> Element
• IL< Operating time (t IL<def ) 0.04...200 s • 49 Trip threshold ΔθH (D thH>) 1.100...1.300 ΔθBH
— Negative sequence - 46 side H
I2H> Element
— Thermal image - 49 side L
Common configuration:
• I2H> Curve type DEFINITE
• Initial thermal image ΔθINL (D thINL ) 0.0...1.0 ΔθBL
IEC/BS A, B, C - ANSI/IEEE MI, VI, EI, I2t or EM
• Reduction factor at inrush (KINRL) 1.0...3.0
• I2HCLP > Activation time (t 2HCLP>) 0.00...100.0 s
• Thermal time constant τ (TL) 1...200 min
• I2H> Reset time delay (t 2H > RES) 0.00...100.0 s
• DthCLPH Activation time (t DthCLPL) 0.00...100.0 s
Definite time
DtHAL1L Element
• 46 First threshold definite time (I2H > def ) 0.100...10.00 InH
• 49 First alarm threshold ΔθAL1L (D thAL1L) 0.3...1.0 ΔθBL
• I2H > def within CLP (I2HCLP>def ) 0.100...10.00 InH
• DtHAL2L Element
• I2H > def Operating time (t 2H > def ) 0.03...200 s
• 49 Second alarm threshold ΔθAL2L (D thAL 2L) 0.5...1.2 ΔθBL
Inverse time
• Dth> Element
• 46 First threshold inverse time (I2H >inv) 0.100...10.00 InH
• 49 Trip threshold ΔθL (D thL>) 1.100...1.300 ΔθBL
• I2H >inv within CLP (I2HCLP>inv) 0.100...10.00 InH
• I2H >inv Operating time (t 2H >inv) 0.02...60.0 s
NT10 - Flyer- 08 - 2012 5
— Phase overcurrent - 50/51 side H — Computed residual overcurrent - 50N/51N side H
IH> Element IEH> Element
• IH> Curve type (IH>Curve) DEFINITE • IEH> Type characteristic (IEH>Curve) DEFINITE
IEC/BS A, B, C, ANSI/IEEE MI, VI, EI, RECTIFIER, I2t or EM IEC/BS A, B, C, ANSI/IEEE MI, VI, EI, EM
• IHCLP > Activation time (t HCLP>) 0.00...100.0 s • IEHCLP > Activation time (t ECLP>) 0.00...100.0 s
• IH> Reset time delay (t H> RES) 0.00...100.0 s • IEH> Reset time delay (t EH > RES) 0.00...100.0 s
Definite time Definite time
• 50/51 First threshold definite time (IH> def ) 0.100...40.0 InH • 50N/51N First threshold definite time (IEH>def) 0.002...10.00 InH
• IH> def within CLP (IHCLP>def ) 0.100...40.0 InH • IEH>def within CLP (IEHCLP>def ) 0.002...10.00 InH
• IH> def Operating time (t H> def ) 0.04...200 s • IEH>def Operating time (t EH > def) 0.04...200 s
Inverse time Inverse time
• 50/51 First threshold inverse timee (IH>inv) 0.100...20.00 InH • 50N/51N First threshold inverse time (IEH >inv) 0.002...2.00 InH
• IH>inv within CLP (IHCLP>inv) 0.100...20.00 InH • IE>inv within CLP (IEHCLP>inv) 0.002...2.00 InH
• IH>inv Operating time (t H>inv) 0.02...60.0 s • IE>inv Operating time (t EH >inv) 0.02...60.0 s

IH>> Element IEH>> Element

• IH>> Type characteristic (IH>>Curve) DEFINITE, I2t • IEHCLP >> Activation time (t EHCLP>>) 0.00...100.0 s
• IHCLP >> Activation time (t HCLP>>) 0.00...100.0 s • IEH>> Reset time delay (t EH >> RES) 0.00...100.0 s
• IH>> Reset time delay (t H>> RES) 0.00...100.0 s Definite time
Definite time • 50N/51N Second threshold inverse time (IEH>>def) 0.002...10.00 InH
• 50/51 Second threshold definite time (IH>>def) 0.100...40.0 InH • IEH>>def within CLP (IEHCLP>>def ) 0.002...10.00 InH
• IH>> def within CLP (IHCLP>>def ) 0.100...40.0 InH • IE>>def Operating time (t E>> def ) 0.03...10.00 s
• IH>> def Operating time (t H>> def ) 0.03...10.00 s IEH>>> Element
Inverse time • IEHCLP >>> Activation time (t EHCLP>>>) 0.00...100.0 s
• 50/51 Second threshold inverse time (IH>>inv) 0.100...20.00 InH • IEH >>> Reset time delay (t EH >>> RES) 0.00...100.0 s
• IH>>inv within CLP (IHCLP>>inv) 0.100...20.00 InH Definite time
• IH>>inv Operating time (t H>>inv) 0.02...10.00 s • 50N/51N Third threshold definite time (IEH>>>def) 0.002...10.00 InH
• IEHCLP >>> def within CLP (IEHCLP>>>def ) 0.002...10.00 InH
IH>>> Element • IEH >>> def Operating time (t EH >>> def ) 0.03...10.00 s
• IHCLP >>> Activation time (t HCLP>>>) 0.00...100.0 s
• IH>>> Reset time delay (t H>>> RES) 0.00...100.0 s — Computed residual overcurrent - 50N/51N side L
Definite time IEL> Element
• 50/51 Third threshold definite time (IH>>> def ) 0.100...40.0 InH • IEL> Curve type (IEL>Curve) DEFINITE
• IH>>> def within CLP (IHCLP>>>def ) 0.100...40.0 InH IEC/BS A, B, C, ANSI/IEEE MI, VI, EI, EM
• IH>>> def Operating time (t H>>> def ) 0.03...10.00 s • IELCLP > Activation time (t ECLP>) 0.00...100.0 s
• IEL> Reset time delay (t EL > RES) 0.00...100.0 s
— Phase overcurrent - 50/51 side L Definite time
IL> Element
• 50N/51N First threshold definite time (IEL >def) 0.002...10.00 InL
• IL> Curve type (IL>Curve) DEFINITE
• IEL>def within CLP (IELCLP>def ) 0.002...10.00 InL
IEC/BS A, B, C, ANSI/IEEE MI, VI, EI, RECTIFIER, I2t or EM
• IEL>def Operating time (t EL > def) 0.04...200 s
• ILCLP > Activation time (t LCLP>) 0.00...100.0 s
Inverse time
• IL> Reset time delay (t L> RES) 0.00...100.0 s
• 50N/51N First threshold inverse time (IEL >inv) 0.002...2.00 InL
Definite time
• IE>inv within CLP (IELCLP>inv) 0.002...2.00 InL
• 50/51 First threshold definite time (IL> def ) 0.100...40.0 InL
• IE>inv Operating time (t EL >inv) 0.02...60.0 s
• IHL> def within CLP (ILCLP>def ) 0.100...40.0 InL
• IL> def Operating time (t L> def ) 0.04...200 s IEL>> Element
Inverse time • IELCLP >> Activation time (t ELCLP>>) 0.00...100.0 s
• 50/51 First threshold inverse time (IL>inv) 0.100...20.00 InL • IEL>> Reset time delay (t EL >> RES) 0.00...100.0 s
• IL>inv within CLP (IHCLP>inv) 0.100...20.00 InL Definite time
• IL>inv Operating time (t L>inv) 0.02...60.0 s • 50N/51N Second threshold inverse time (IEL>>def) 0.002...10.00 InL
• IEL>>def within CLP (IELCLP>>def ) 0.002...10.00 InL
IL>> Element • IE>>def Operating time (t E>> def ) 0.03...10.00 s
• IL>> Type characteristic (IL>>Curve) DEFINITE, I2t
• IHLCLP >> Activation time (t LCLP>>) 0.00...100.0 s IEL>>> Element
• IL>> Reset time delay (t L>> RES) 0.00...100.0 s • IELCLP >>> Activation time (t ELCLP>>>) 0.00...100.0 s
Definite time • IELCLP >>> Reset time delay (t EL >>> RES) 0.00...100.0 s
• 50/51 Second threshold definite time (IL>>def) 0.100...40.0 InL Definite time
• IL>> def within CLP (ILCLP>>def ) 0.100...40.0 InL • 50N/51N Third threshold definite time (IEL>>>def) 0.002...10.00 InL
• IL>> def Operating time (t L>> def ) 0.03...10.00 s • ELCLP >>> def within CLP (IELCLP>>>def ) 0.002...10.00 InL
Inverse time • IEL >>> def Operating time (t EL >>> def ) 0.03...10.00 s
• 50/51 Second threshold inverse time (IL>>inv) 0.100...20.00 InL
• IL>>inv within CLP (ILCLP>>inv) 0.100...20.00 InL — Measured residual overcurrent IE1 - 50N/51N
• IL>>inv Operating time (t L>>inv) 0.02...10.00 s IE1> Element
• IE1> Curve type (IE1>Curve) INDIPENDENTE
IL>>> Element IEC/BS A, B, C, ANSI/IEEE MI, VI, EI, EM
• ILCLP >>> Activation time (t LCLP>>>) 0.00...100.0 s • IE1CLP > Activation time (t E1CLP>) 0.00...100.0 s
• IL>>> Reset time delay (t L>>> RES) 0.00...100.0 s • IE1> Reset time delay (t E1> RES) 0.00...100.0 s
Definite time Definite time
• 50/51 Third threshold definite time (IL>>> def ) 0.100...40.0 InL • 50N/51N First threshold definite time (IE1>def) 0.002...10.00 IEn1
• IL>>> def within CLP (ILCLP>>>def ) 0.100...40.0 InL • IE1>def within CLP (IE1CLP>def ) 0.002...10.00 IEn1
• IL>>> def Operating time (t L>>> def ) 0.03...10.00 s • IE1>def Operating time (t E1> def) 0.04...200 s
Inverse time
• 50N/51N First threshold inverse time (IE1>inv) 0.002...2.00 IEn1
• IE1>inv within CLP (IE1CLP>inv) 0.002...2.00 IEn1
• IE1>inv Operating time (t E1>inv) 0.02...60.0 s
6 NT10 - Flyer- 08 - 2012
 IE1>> Element — Breaker failure - BF side H
• IE1CLP >> Activation time (t E1CLP>>) 0.00...100.0 s BF Phase current threshold (IBFH >) 0.05...1.00 InH
• IE1>> Reset time delay (t E1>> RES) 0.00...100.0 s BF Residual current threshold (IEBFH >) 0.01..2.00 InH
Definite time BF Time delay (t BFH) 0.06...10.00 s
• 50N/51N Second threshold inverse time (IE1>>def)0.002...10.00 IEn1
• IE1>>def within CLP (IE1CLP>>def ) 0.002...10.00 IEn1 — Breaker failure - BF side L
• IE1>>def Operating time (t E1>> def ) 0.03...10.00 s BF Phase current threshold (IBFL >) 0.05...1.00 InL
BF Residual current threshold (IEBFL >) 0.01..2.00 InL
IE1>>> Element BF Time delay (t BFL) 0.06...10.00 s
• IE1CLP >>> Activation time (t E1CLP>>>) 0.00...100.0 s
• IE1CLP >>> Reset time delay (t E1>>> RES) 0.00...100.0 s — Selective block - BLOCK2
Definite time Selective block IN:
• 50N/51N Third threshold definite time (IE1>>>def) 0.002...10.00 IEn1 • BLIN Max activation time for phase protections (tBH-Iph)
• IE1CLP >>> def within CLP (IE1CLP>>>def ) 0.002...10.00 IEn1 0.10...10.00 s
• IE1>>> def Operating time (t E1>>> def ) 0.03...10.00 s • BLIN Max activation time for earth protections (tBH-IE)
0.10...10.00 s
— Measured residual overcurrent IE2 - 50N/51N Selective block OUT:
IE2> Element • BLOUT Dropout time delay for phase protections (tFH-Iph) 0.00...1.00 s
• IE2> Curve type (IE1>Curve) INDIPENDENTE • BLOUT Drop-out time delay for ground protections (tFH-IE)0.00...1.00 s
IEC/BS A, B, C, ANSI/IEEE MI, VI, EI, EM • BLOUT Drop-out time delay for phase and ground protections
• IE2CLP > Activation time (t E1CLP>) 0.00...100.0 s (tFH-Iph/IE) 0.00...1.00 s
• IE2> Reset time delay (t E1> RES) 0.00...100.0 s
Definite time — Internal selective block - BLOCK4
• 50N/51N First threshold definite time (IE1>def) 0.002...10.00 IEn2 Output selective block dropout time for phase protections (tF-IPh)
• IE2>def within CLP (IE2CLP>def ) 0.002...10.00 IEn2 0.00...10.00 s
• IE2>def Operating time (t E2 > def) 0.04...200 s Output selective block dropout time for ground protections (tF-IE)
Inverse time 0.00...10.00 s
• 50N/51N First threshold inverse time (IE2 >inv) 0.002...2.00 IEn2 — CT supervision - 74CT side H
• IE2>inv within CLP (IE2CLP>inv) 0.002...2.00 IEn2 74CT Threshold (S H <) 0.10...0.95
• IE2>inv Operating time (t E2 >inv) 0.02...60.0 s 74CT Overcurrent threshold (I H* ) 0.10...1.00 I nH
S H < Operate time (t SH) 0.03...200 s
IE2>> Element
• IE2CLP >> Activation time (t E2CLP>>) 0.00...100.0 s — CT supervision - 74CT side L
• IE2>> Reset time delay (t E2 >> RES) 0.00...100.0 s
74CT Threshold (S L<) 0.10...0.95
Definite time 74CT Overcurrent threshold (I L* ) 0.10...1.00 I nH
• 50N/51N Second threshold inverse time (IE2 >>def) 0.002...10.00 IEn2 S L< Operate time (t SL ) 0.03...200 s
• IE2>>def within CLP (IE2CLP>>def ) 0.002...10.00 IEn2
• IE2>>def Operating time (t E2>> def ) 0.03...10.00 s
— Circuit Breaker supervision side H
IE2>>> Element Number of CB trips (N.OpenH) 0...10000
• IE1CLP >>> Activation time (t E2CLP>>>) 0.00...100.0 s Cumulative CB tripping currents (SumIH) 0...5000 InH
• IE2CLP >>> Reset time delay (t E2 >>> RES) 0.00...100.0 s CB opening time for I^2t calculation ΣI2t (t breakH) 0.05...1.00 s
Definite time Cumulative CB tripping I^2t (SumI^2tH) 0...5000 I nH2.s
• 50N/51N Third threshold definite time (IE2>>>def) 0.002...10.00 IEn2 CB max allowed opening time (t breakH >) 0.05...1.00 s
• IE2CLP >>> def within CLP (IE2CLP>>>def ) 0.002...10.00 IEn2
• IE2 >>> def Operating time (t E2 >>> def ) 0.03...10.00 s — Circuit Breaker supervision side L
Number of CB trips (N.OpenL ) 0...10000
— Low impedance restricted ground fault - 64REF side H Cumulative CB tripping currents (SumIL ) 0...5000 InL
• 64REF Minimum threshold (IREFH>) 0.05...2.00 IEn1 CB opening time for I^2t calculation ΣI2t (t break L ) 0.05...1.00 s
• 64REF Intentional delay (t REFH>) 0.03...60.00 s Cumulative CB tripping I^2t (SumI^2tL ) 0...5000 I nL2.s
CB max allowed opening time (t break L >) 0.05...1.00 s
— Low impedance restricted ground fault - 64REF side L
• 64REF Minimum threshold (IREFL>) 0.05...2.00 IEn2 — Pilot wire diagnostic
• 64REF Intentional delay (t REFL>) 0.03...60.00 s BLOUT1 Diagnostic pulses period (PulseBLOUT1)
OFF - 0.1-1-5-10-60-120 s
— Differential for two windings transformer - 87T BLIN1 Diagnostic pulses control time interval (PulseBLIN1)
Harmonic restraint: OFF - 0.1-1-5-10-60-120 s
• 2nd harmonic restraint (2nd-REST>) 10...80% Id
• 5th harmonic restraint (5th-REST>) 10...80% Id
• Restraint reset intentional delay (t HREST-RES) 0.00...10.00 s
• Cross-harmonic restraint enabling (CROSS H-RES) ON/OFF
• CT saturation detector
• 87T Saturation detector enable (Sat-Det) ON/OFF
• 87T Saturation detector reset intentional delay (tSat-Det-RES)
0.00...0.50 s
• Id> Element Definite time
• 87 First threshold definite time (Id>) 0.05...2.00 Inref
• 87T First stretch slope percentage (K1) 10...50%
• 87T Second stretch slope percentage (K2) 25...100%
• 87T Second stretch Intersection with vertical axis (Q) 0.00...3.00 Inref
• 87T First threshold operating time 0.04 s
Id>> Element Definite time
• 87T Second threshold definite time (Id>>) 0.5...30.00 Inref
• 87T Second threshold operating time 0.03 s
NT10 - Flyer- 08 - 2012 7
 METERING & RECORDING — Digital Fault Recorder (Oscillography)
File format COMTRADE
— Measured parameters Records depending on setting [1]
Direct: Recording mode circular
• Frequency f Sampling rate 16 sample/cycle
• Fundamental RMS phase currents side H I L1H , I L 2H , I L 3H
Trigger setup:
• Fundamental RMS phase currents side L I L1L , I L 2L , I L 3L
• Pre-trigger time 0.05...1.00 s
• Fundamental RMS residual currents (measured) I E1, I E2
• Post-trigger time 0.05...60.00 s
Calculated: • Trigger from inputs IN1, IN2...INx
• Calculated residual current side H and L I EH , I EL • Trigger from outputs K1...K6...K10
• Thermal image side H and L D ThH , D ThL • Communication ThySetter
• Maximum current between IL1-IL2-IL3 side H and L ILmaxH, ILmaxL
Set sample channels:
• Minimum current between IL1-IL2-IL3 side H and L ILminH, ILminL
• Instantaneous phase currents side H i L1H, i L2H, i L3H
• Average current between IL1-IL2-IL3 side H and L ILH, ILL
• Instantaneous phase currents side L i L1L, i L2L, i L3L
• Compensated phase currents side H I L1cH , I L 2cH , I L 3cH
• Compensated phase currents side H i L1cH , i L 2cH , i L 3cH
• Compensated phase currents side L IL1cL , IL2cL , IL3cL
• Compensated phase currents side L i L1cL , i L 2cL , i L 3cL
• Stabilization currents (87 element) ISL1, ISL2 , ISL3
• Stabilization currents (87 element) i SL1, i SL 2 , i SL 3
• Differential currents IdL1, IdL2 , IdL3
• Differential currents i dL1, i dL 2 , i dL 3
• Stabilization current (64REF-1 element) side H IESH
• Instantaneous measured residual currents i E1, i E2
• Stabilization current (64REF-2 element) side L IESL
Set analog channels (Analog 1...12):
Sequence:
• Frequency f
• Positive sequence current side H and L I 1H , I 1L
• Fundamental RMS phase currents side H I L1H , I L 2H , I L 3H
• Negative sequence current side H and L I 2H , I 2L
• Fundamental RMS phase currents s side L I L1L , I L 2L , I L 3L
• Maximum of the second harmonic phase currents/fundamental
• Thermal image side H and side L D ThH , D ThL
component percentage ratio side H and L I-2nd /IL I2H /I1H, I2L /I1L
• Fundamental RMS residual currents (measured) I E1, I E2
2nd harmonic: • Fundamental RMS residual currents (computed) side H and L I EH , I EL
• Second harmonic differential currents I d2L1, I d2L 2 , I d2L 3 • Compensated phase currents side H I L1cH , I L 2cH , I L 3cH
5th harmonic: • Compensated phase currents side L I L1cL , I L 2cL , I L 3cL
• Fifth harmonic differential currents I d5L1, I d5L 2 , I d5L 3 • Stabilization currents (87 element) I SL1, I SL 2 , I SL 3
On demand: • Differential currents I dL1, I dL 2 , I dL 3
• Phase fixed currents demand side H I L1FIXH , I L 2FIXH , I L 3FIXH • Second harmonic differential currents Id2L1, Id2L2 , Id2L3
• Phase rolling currents demand side HI L1ROLH , I L 2ROLH , I L 3ROLH • Fifth harmonic differential currents I d5L1, I d5L 2 , I d5L 3
• Phase peak currents demand side HI L1MA XH , I L 2MA XH , I L 3MA XH • Stabilization current (64REF-1 element) side H I ESH
• Phase minimum currents demand side H I L1MINH , I L 2MINH , I L 3MINH • Stabilization current (64REF-2 element) side L I ESL
• Phase fixed currents demand side L I L1FIXL , I L 2FIXL , I L 3FIXL • Fundamental RMS positive sequence currents side H and L I 1H , I 1L
• Phase rolling currents demand side L I L1ROLL , I L 2ROLL , I L 3ROLL • Fundamental RMS negative sequence currents side H and LI 2H , I 2L
• Phase peak currents demand side L I L1MA XL , I L 2MA XL , I L 3MA XL • Maximum of the second harmonic phase currents/fundamental
• Phase minimum currents demand side L I L1MINL , I L 2MINL , I L 3MINL component percentage ratio side H and L I-2nd /IL I2H /I1H, I2L /I1L
• Temperature T1...T8
— Event recording (SER) Set digital channels (Digital 1...12):
Number of events 300 • Output relays state K1...K6...K10
Recording mode circular • Binary inputs state IN1, IN2...INx
Trigger: Note [1] - For instance, with following setting:
• Start/Trip of enabled protection or control element • Pre-trigger time and Post-trigger time 0.25 s
• Binary inputs switching (OFF/ON or ON/OFF) IN1...INx • Sampled channels i L1H, i L2H, i L3H, i L1L, i L2L, i L3L, i dL1, i dL2 , i dL3 , i E1, i E2
• Setting changes • Analog channels I L1H , I L2H , I L3H , I L1L , I L2L , I L3L , I dL1, I dL2 , I dL3 , I E1, I E2
• Auxiliary supply Power UP/Power DOWN • Digital channels K1, K2, K3, K4, K5, K6, IN1, IN2
Data recorded: up to 200 records can be stored with f = 50 Hz
• Counter (resettable by ThySetter) 0...10 9
• Cause binary input/trip/setting change/Power ON/OFF
• Time stamp Date and time

— Fault recording (SFR)

Number of faults 20
Recording mode circular
Trigger:
• Output relays of enabled protection or control element (OFF-ON)
• External trigger (binary inputs) IN1...INx
Data recorded:
• Counter (resettable by ThySetter) 0...10 9
• Time stamp Date and time
• Cause tripped element
• Phase currents side H and side L IL1Hr, IL2Hr, IL3Hr, IL1Lr, IL2Lr, IL3Lr
• Measured residual currents I E1r, I E2r
• Differential currents I dL1r, I dL 2r, I dL 3r
• 2nd harmonic of differential currents I d2L1r, I d2L 2r, I d2L 3r
• 5th harmonic of differential currents I d5L1r, I d5L 2r, I d5L 3r
• Thermal image side H and side L D T hetaH-r, D T hetaH-r
• Binary inputs state IN1, IN2...INx
• Output relays state K1...K6...K10
• Fault cause info (operating phase) L1, L2, L3

8 NT10 - Flyer- 08 - 2012

— One line diagram NT10

74CT 37 46 49 50/51

74TCS BF
side H

side H or side L
50N.1/51N.1
64REF 50N/51N

87NHIZ.1
side H
87T
side H or side L side L

50N.2/51N.2
64REF 50N/51N
87NHIZ.2

74TCS BF side L

74CT 37 46 49 50/51

Control functions
COMMUNICATION
- RS232
METERING - Modbus RS485
- I L1H...I L3H,I L1L...I L3L,... - Modbus TCP/IP
- Oscillography - IEC 870-5-103/DNP3
- Events & Faults log - IEC 61850

NT10

74CT 37 46 49 50/51

74TCS BF
side H

side H or side L
50N.1/51N.1
64REF 50N/51N

87NHIZ.1
side H
87T
side H or side L side L

50N.2/51N.2
64REF 50N/51N
87NHIZ.2

side L
74TCS BF

74CT 37 46 49 50/51

Control functions
COMMUNICATION
- RS232
METERING - Modbus RS485
- I L1H...I L3H,I L1L...I L3L,... - Modbus TCP/IP
- Oscillography - IEC 870-5-103/DNP3
- Events & Faults log - IEC 61850

NT10 - Flyer- 08 - 2012 9

— Connection diagram example

L1 L2 L3 NT10

P2 C9
S2 A3
C10 IL1H K1
S1 A4
P1 C11 A5

C12 IL2H K2 A6

SIDE H
A7
C13
A8

OUTPUT RELAYS
C14 IL3H
K3 A9

K4 A10
P2 C15
S1 A11
IE1
S2 C16
P1 K5 A12

K6 A13

A14
CURRENT INPUTS

F1
F2
F3
RS485

B- F4
C7 Supervision
A+ F5
IE2
unit
P1 C8
S1
S2
P2
ETHERNET
SIDE L

C1
D1
HUB
C2 IL1L
P1
S1 C3
S2
P2 C4 IL2L
C5 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28
THYBUS

E1
IL3L
C6
OUTPUT INPUT
RUN
BUS
ON

1
2
3
4
5

MODULO 4 RELE’ + 8 INGRESSI DIGITALI MRI

4 RELAYS + 8 BINARY INPUTS MODULE
BLOCK OUT
BLOCK IN

BLOUT- 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27

A17 A15
A18 BLOUT+
A16
BINARY INPUTS

A19
IN1
A20 FRONT PANEL
A21
IN2
RS232

A22

A1 ≅
UAUX
A2

NOTE
- Incoming currents to the protected transformer must match to the the reference current inputs of the relay, with current direction leaving the
protected transformer must match current output from the current inputs of the relay.
- Incoming currents in the reference terminals of of the relay current inputs are considered positive, the outgoing negative.
- This convention applies to indicate the P1 CTs polarity toward the protected transformer.

Transformer protection - differential (87) and LV side restricted earth fault protection (64REF)

10 NT10 - Flyer- 08 - 2012

 L1 L2 L3 NT10

P2 C9
S2 SIDE H
IL1H BF
S1 C10
P1 C11

C12 IL2H 74CT 37 46 I2/I1 49 50/51

SIDE H
C13
50N/51N
C14 IL3H

P2 C15
S1
IE1 50N.1/51N.1
S2 C16
P1

CB position

87T
CURRENT INPUTS

C7
IE2 50N.2/51N.2
C8

G SIDE L
50/51 50N/51N
C1

C2 IL1L 74CT 37 46 I2/I1 49

P1
S1 C3
S2
SIDE L

P2 C4 IL2L
C5
IL3L
C6

P1
S1 BF
BINARY INPUTS

S2
P2
CB position

NOTE
- Incoming currents to the protected transformer must match to the the reference current inputs of the relay, with current direction leaving the
protected transformer must match current output from the current inputs of the relay.
- Incoming currents in the reference terminals of of the relay current inputs are considered positive, the outgoing negative.
- This convention applies to indicate the P1 CTs polarity toward the protected transformer.

Differential protection for Transformer-Generator system

NT10 - Flyer- 08 - 2012 11

 DIMENSIONS
FRONT VIEW REAR VIEW
128.5
120 ø 4.5 110
107 101

D1 D1

C C
A1 A1
1 1
A2 A2
9 9

ø 4.5 A3
A4
A5
2

3
10 RX
F1
F2
A3
A4
A5
2

3
10 RX
F1
F2
F3 F3
A6 11 F4 A6 11 F4
TX TX
A7 4 F5 A7 4 F5
A8 12 A8 12
5 5
A9 13 B1 A9 13 B1
A10 6 B2 A10 6 B2

171
149

200
168
177

A11 14 B3 A11 14 B3
A12 7 B4 A12 7 B4
ON 1 2 3 4 5 START ON 1 2 3 4 5 START A13 15 B5 A13 15 B5
A14 8 B6 A14 8 B6
80

TRIP TRIP
A15 16 B7 A15 16 B7
A16 B8 A16 B8

A17 A17
A18 A18
A19 A19
A20 A20
A21 A21
A22 A22
31

E1 E1

20
FLUSH MOUNTING PROJECTING MOUNTING FLUSH MOUNTING PROJECTING MOUNTING
(Separate operator panel)

SIDE VIEW

212.5 275
25 15
205 30 5 30 ø 4.5
170

FLUSH MOUNTING SEPARATE PROJECTING MOUNTING PROJECTING MOUNTING

OPERATOR PANEL (Separate operator panel) (Stand alone)

RACK MOUNTING FLUSH MOUNTING CUTOUT

482.6 102.5 ±0.3

465 70
177 (4U)

161
101.6

154

ON 1 2 3 4 5 START ON 1 2 3 4 5 START ON 1 2 3 4 5 START ON 1 2 3 4 5 START

TRIP TRIP TRIP TRIP

N.4 holes ø 3.5

Headquarter: 20139 Milano - Piazza Mistral, 7 - Tel. +39 02 574 957 01 ra - Fax +39 02 574 037 63
Factory: 35127 Padova - Z.I. Sud - Via dell’Artigianato, 48 - Tel. +39 049 894 770 1 ra - Fax +39 049 870 139 0

www.thytronic.it www.thytronic.com thytronic@thytronic.it