FOREWORD

This manual is intended for persons who engage in maintenance operations, and explains procedures for dis-
assembly and reassembly of the machine, check and maintenance procedures, maintenance reference values,
troubleshooting and outline specifications, etc. Please use this manual as a reference in service activities to
improve maintenance techniques.
Further, please be advised that items contained in this manual are subject to change without notice due to design
modifications, etc.

MACHINE FRONT AND REAR, LEFT AND RIGHT

The end where the dozer blade is mounted is the front and the end with the travel motors is the rear. Also the right
and left sides of the operator when he is seated in the operatorʼs seat are the right and left sides of the machine.

MACHINE SERIAL NUMBER

The machine serial number is stamped on the identification plate. When sending reports and inquiries, and when
ordering parts, etc., be sure to include this number.

MANUAL CONTROL
Information on those to whom this manual is distributed is recorded in the ledger in the section in charge at this
company, so please decide on a person to be in charge of it and control it. When there are updates or additions,
etc., we will notify the person in charge.

SYMBOLS
means “Please refer to the section quoted.”

Indicates the tightening torque at the specific section that requires special attention in designing.

Indicates the mass of a part or device.

0-2
 I . GENERAL
II . SPECIFICATIONS
III . MACHINE CONFIGURATION
IV . HYDRAULIC UNITS
V. TROUBLESHOOTING
VI . ENGINE

0-3
I . GENERAL

1-1
 GENERAL

CONTENTS

Safety precautions ...................................................................................................................................................3

Cautions during Disassembly and Assembly ..........................................................................................................9
Cautions during Removal and Installation of the Hydraulic Units .........................................................................9
Cautions during Removal and Installation of Piping ............................................................................................10
Handling of Seals ..................................................................................................................................................10
Tightening Torques ............................................................................................................................................... 11

I-2
 GENERAL
SAFETY PRECAUTIONS

SAFETY ALERT SYMBOL

This symbol means Attention! Be Alert! Your Safety Is Involved.
The message that follows the symbol contains important information about safety.
Read and understand the message to avoid personal injury or death.

■ SIGNAL WORDS
Safety messages appearing in this manual and on machine decals are identified by the words “DANGER”,
“WARNING” and “CAUTION”. These signal words mean the following:

DANGER WARNING CAUTION

The word “DANGER” indi- The word “WARNING” indi- The word “CAUTION” indi-
cates an imminently hazard- cates a potentially hazardous cates a potentially hazardous
ous situation which, if not situation which, if not avoided, situation which, if not avoided,
avoided, can result in serious could result in serious injury may result in minor or moder-
injury or death. or death. ate injury.

IMPORTANT: The word “IMPORTANT” is used to alert against operators and maintenance personnel
about situations which can result in possible damage to the machine and its components.

This manual is intended for trained and qualified personnel only. Warnings or cautions described in this manual
do not necessarily cover all safety measures. For maintenance work, each person must take adequate safety
precautions against possible hazards present in the respective working environment.

Observe all safety rules

• Operation, inspection and maintenance of this
machine must be performed only by a trained and
qualified person.
• All rules, regulations, precautions and safety pro-
cedures must be understood and followed when
performing operation, inspection and mainte-
nance of this machine.
• Do not perform any operation, inspection and
maintenance of this machine when under the
adverse influence of alcohol, drugs, medication,
fatigue, or insufficient sleep.

• Wear a hard hat, safety shoes, safety glasses, filter

Wear appropriate clothing and personal
mask, heavy gloves, ear protection and other pro-
protective equipment
tective equipment as required by job conditions.
• Do not wear loose clothing or any accessory that Wear required appropriate equipment such as
can catch on controls or in moving parts. safety glasses and filter mask when using grind-
• Do not wear oily or fuel stained clothing that can ers, hammers or compressed air, as metal frag-
catch fire. ments or other objects can fly and cause serious
injury.
• Use hearing protection when operating the ma-
chine. Loud prolonged noise can cause hearing
impairments, even the total loss of hearing.

I-3
 GENERAL

Provide a fire extinguisher and first aid Anti-explosive lighting

kit

Use anti-explosive electrical fixtures and lights

• Know where a fire extinguisher and first aid kit when inspecting fuel, oil, coolant, battery fluid, etc.
are located and understand how to use them. If lighting that is not anti-explosive should break,
• Know how to contact emergency assistance and the substance could ignite, resulting in serious injury
first aid help. or death.

Attach a “DO NOT OPERATE” tag Do not allow unauthorized personnel in

the work area
Severe injury could result if an unauthorized person
should start the engine or touch controls during in-
spection or maintenance.
• Stop the engine and remove the key before per-
forming maintenance.
• Attach a “DO NOT OPERATE” tag to the starter
switch or control lever.

Use the correct tools

Do not allow unauthorized personnel in the work
area. Chips or other debris can fly off machine parts
when grinding, welding or using a hammer.

Prepare the work area

• Select a firm, level work area. Make sure there is
adequate light and, if indoors, ventilation.
• Clear obstacles and dangerous objects. Eliminate
Do not use damaged or weakened tools or tools de- slippery areas.
signed for other purposes. Use tools suited for the
operation at hand.
Cautions on tilting up the platform
• Raising or lowering the platform while the engine
Replace important safety parts
is running may cause the machine to move, and
periodically
cause serious injury or death. Lower the work-
• Replace fuel hoses periodically. Fuel hoses be- ing equipment to the ground and stop the engine
come weaker over time, even if they appear to be before raising or lowering the platform.
in good shape. • When the floor is tilted up, support it firmly with
• Replace important safety parts whenever an ir- the stopper to prevent it from falling.
regularity is found, even if it is before the normal
time for replacement.

I-4
 GENERAL

Always clean the machine Securely block the machine or any com-
ponent that may fall

• Clean the machine before performing mainte-

nance. • Before performing maintenance or repairs under
• Cover electrical parts when washing the machine. the machine, set all working equipment against
Water on electrical parts could cause short-cir- the ground or in the lowermost position.
cuits or malfunctions. • Securely block the tracks.
Do not use water or steam to wash the battery, • If you must work beneath the raised machine or
sensors, connectors or the operatorʼs seat area. equipment, always use wood blocks, jack-stands
or other rigid and stable supports. Never get un-
der the machine or working equipment if they
are not sufficiently supported. This procedure is
Stop the engine before performing
especially important when working on hydraulic
maintenance
cylinders.
• Avoid lubrication or mechanical adjustments with
the machine in motion or with the engine running
while stationary.
Securely block the working equipment
• If maintenance must be performed with the engine
running, always work as a 2-person team with To prevent unexpected movement, securely block
one person sitting in the operatorʼs seat while the the working equipment when repairing or replacing
other works on the machine. the cutting edges or bucket teeth.
• When performing maintenance, be sure to
keep your body and clothing away from mov-
ing parts.
Secure the engine hood or cover when
opened
Be sure to secure the engine hood or cover when
Stay clear of moving parts
opening it. Do not open the engine hood or cover on
slopes or in strong wind.

Place heavy objects in a stable position

• Stay clear of all rotating and moving parts. Wrap-

ping or entanglement may result in serious injury
or death.
• Keep hands, clothing and tools away from the
rotating fan and running fan belts.
When removing or installing the hoe attachment,
place it in a stable position so that it does not tip
over.

I-5
 GENERAL

Cautions on working on the machine Handling of hoses

Fuel, oil or hydraulic fluid leaks can cause a fire.
• Do not twist, bend or hit the hoses.
• Never use twisted, bent or cracked hoses, tubes
and pipes. They may burst.
• Retighten loose connections.

Be careful with hot and pressurized

components
• When performing maintenance on the machine,
clean up the foot area and strictly observe the fol-
lowing so as not to fall:
• Do not spill oil or grease.
• Do not leave tools laying around.
• When walking, watch your step.
• Never jump off the machine. Use the steps and
handrails when climbing on and off the machine,
and always support your body at three points with
your hands and feet.
• Use protective equipment as required by job con- Stop the engine and allow the machine to cool down
ditions. before performing inspection and maintenance.
• The engine, muffler, radiator, hydraulic lines,
sliding parts and many other parts of the machine
Use caution when fueling
are hot directly after the engine is stopped. Touch-
ing these parts will cause burns.
• The engine coolant, oil and hydraulic fluid are
also hot and under high pressure.
Be careful when loosening caps and plugs. Work-
ing on the machine under these conditions could
result in burns or injuries due to the hot oil spurt-
ing out.

Be careful with hot cooling systems

• Do not smoke or permit open flames while fuel-

ing or near fueling operations.
• Never remove the fuel cap or refuel with the en-
gine running or hot. Never allow fuel to spill on
hot machine components.
• Maintain control of the fuel filler nozzle when
filling the tank.
• Do not fill the fuel tank to capacity. Allow room
for expansion. Do not remove the radiator cap or drain plugs when
• Clean up spilled fuel immediately. the coolant is hot. Stop the engine, let the engine
• Tighten the fuel tank cap securely. Should the and radiator cool and loosen the radiator cap or drain
fuel cap be lost, replace it only with the original plugs slowly.
manufacturerʼs approved cap. Use of a non-ap-
proved cap without proper venting may result in
pressurization of the tank.
• Never use fuel for cleaning purposes.
• Use the correct fuel grade for the operating sea-
son.

I-6
 GENERAL
High pressure nitrogen gas is enclosed in the accu-
Be careful with fluids under pressure
mulator and incorrect handling could possibly bring
about serious injury due to explosion. The following
matters should be strictly observed:
• Do not disassemble.
• Do not bring close to fire or throw into a fire.
• Do not make hole, weld, or fuse.
• Do not subject to shock such as hitting or rolling.
• At time of disposal, it will be necessary to release
the enclosed gas. Please contact a Takeuchi sales
or service agent.

Be careful with grease under pressure

Pressure can be maintained in the hydraulic circuit
long after the engine has been shut down.
• Release all pressure before working on the hy-
draulic system.
• Hydraulic fluid under pressure can penetrate the
skin or eyes and cause injury, blindness or death.
Fluid escaping from a small hole can be almost
invisible. Wear a safety goggles and heavy gloves
and use a piece of cardboard or wood to search E3A6201

for suspected leaks.

If fluid is injected into the skin, it must be removed The track adjuster contains highly pressurized
within a few hours by a doctor familiar with this grease. If the tension is adjusted without following
type of injury. the prescribed procedure, the grease discharge valve
may fly off, resulting in injury.
• Loosen the grease discharge valve slowly. Do not
unfasten it more than one full turn.
Release all pressure before working on
• Do not put your face, arms, legs or body in front
the hydraulic system
of the grease discharge valve.
Oil may spurt out if caps or filters are removed or
pipes disconnected before releasing the pressure in
the hydraulic system.
Disconnect the battery
• Gradually loosen the vent plug to relieve tank
pressure.
• Move all the control levers and pedals several
times in all directions to release the pressure from
the working equipment circuitry. (For link type
controls)
• When removing plugs or screws or disconnect-
ing hoses, stand to the side and loosen slowly
to gradually release the internal pressure before
removing.
Disconnect the battery before working on the electri-
cal system or doing any welding. Remove the nega-
Handling of the Accumulator
tive (–) battery cable first. When reconnecting the
battery, connect the negative (–) battery cable last.

I-7
 GENERAL

Avoid battery hazards Checks after maintenance

• Batteries contain sulfuric acid which will damage • Gradually raise the engine speed from a low idle
eyes or skin on contact. to maximum speed and check that no oil or air is
• If acid contacts eyes, flush immediately with leaking from serviced parts.
clean water and get prompt medical attention. • Move the controls and check that the machine is
• If acid is accidentally swallowed, drink large operating properly.
quantities of water or milk and call a physician
immediately.
• If acid contacts skin or clothing, wash off imme-
Disposing of wastesa
diately with clean water.
• Wear safety glasses and gloves when working
with batteries.
• Batteries generate flammable and explosive gas-
es. Keep arcs, sparks, flames and lighted tobacco
away.
• Use a flashlight to check battery electrolyte lev-
el.
• Stop the engine and shut off electrical equipment
while inspecting or handling the battery.
• Do not short circuit the battery posts with metal • Funnel spent fluids from the machine into con-
items. tainers. Disposing of fluids improperly destroys
• Always unfasten the negative (–) battery cable the environment.
first when disconnecting the battery cable. Al- • Follow the prescribed regulations when disposing
ways connect the negative (–) battery cable last of oil, fuel, engine coolant, refrigerant, solvents,
when fastening the battery cable. filters, batteries or other harmful substances.
• Loose battery terminals may result in sparks. Be
sure to fasten terminals tightly.
• Make sure the vent caps are tightened securely.
• Do not charge a battery or jump-start the engine if
the battery is frozen. Warm to 15°C (60°F) or the
battery may explode.

Have a Takeuchi service agent repair

welding cracks or other damage
Ask a Takeuchi service agent to repair any welding
problems which are detected. If not feasible, make
sure the welding is done by a qualified person in a
properly equipped workplace.

Safety signs
• Keep all safety signs clean and legible.
• Replace all missing, illegible or damaged safety
and warning signs.

I-8
 GENERAL
CAUTIONS DURING DISASSEMBLY AND CAUTIONS DURING REMOVAL AND INSTALLA-
ASSEMBLY TION OF THE HYDRAULIC UNITS

1. Clean the machine before disassembly opera- 1. Make sure that the hydraulic oilʼs temperature
tion. has dropped.

2. Before disassembly, check the machine condi- 2. To prevent a loss of flow of the hydraulic oil, the
tions and record them. residual pressure in the piping and the internal
• Model, Machine Serial Number, Hourmeter pressure in the hydraulic oil tank should be bled
• Reason for Repairs, Repair History out.
• Dirtiness of Filters
• Fuel and Oil Conditions 3. Be sure to install caps or plugs on all openings
• Damage to each parts, etc. in the hydraulic unit to prevent dirt from getting
into the unit through the openings.
3. To make reassembly operations easy, make
matching marks at the necessary points. PLUG

4. Clean all disassembled parts and new parts, then

arrange them in the proper sequence.

5. Be sure to replace all seals and cotter pins, etc.,

with new parts.

6. Keep parts which should not come in contact PLUG

with oil and water separate from parts with oil
on them.
• Electrical Parts, Rubber, V-Belts, etc. Y2-A103E

7. When installing bearings, bushings and oil seals, 4. It is easy to mistake hydraulic oil adhering to the
as a rule, use a press. When a hammer, etc., is hydraulic unit for an oil leak, so wipe the unit
used, it leaves bruises. off thoroughly.

8. Wipe all joining surfaces clean so that there is 5. Be sure that no damage is done to the plating on
no dirt or dust adhering to them. the rod in the hydraulic cylinder.

9. Wrap seal tape from the front end, Wrapping it 6. As a rule, removal and installation of the hy-
tight and leaving 1 or 2 threads bare, Overlap the draulic cylinder should be done with the rod
tape by about 10 mm. fully retracted.

SEALING TAPE 7. Be sure to bleed the air after replacing the hy-
draulic oil or removing any of the hydraulic
devices.
• Damage to each parts, etc.
“III. Machine Configuration, Hydraulic
System”

8. After installation of the hydraulic unit, be sure

to pressurize the hydraulic tank. If this operation
is forgotten, it could cause cavitation of the hy-
LEAVE 1 OR 2 THREAD MARGIN
draulic pump. Also, it could have a drastic effect
Y2-A102E
on the life of the hydraulic pump.
“III. Machine Configuration, Hydraulic
10. When fitting the snap rings, the bigger, rounder System”
side of their circumferences should face the
mating surfaces.

I-9
 GENERAL

CAUTIONS DURING REMOVAL AND INSTAL- HANDLING OF SEALS

LATION OF PIPING
1. Clean the grooves for O-rings and if there is any
1. When hydraulic hoses are installed, tighten them burr, etc., remove it.
once to the prescribed torque, then loosen them
slightly and retighten them to the prescribed
torque.
• Tighten the fittings after the installation sur-
BURR
faces fit snugly together.
• Pieces wrapped with seal tape are excluded.

2. Use 2 spanners, each on an opposite side, to DIRT

remove and tighten fittings so that the hoses or
steel pipes are not twisted.
Y2-A105E

2. Be careful not to twist O-rings. If an O-ring is

twisted, remove the twist with the fingertips.

3. During insertion, be careful not to damage the

seal.

4. Handling of Floating Seals

• Wipe all oil off the O-ring and housing of the
floating seal.
• When assembling, apply a thin coating of
gear oil to the contact surface of the housing.
• After assembly, turn the seal 2 or 3 times to
3. After installation of hydraulic hoses or steel get it to fit snugly.
pipes, apply the maximum working pressure 5
or 6 times and confirm that there is no leakage. 5. Apply grease to the lip of the oil seal.
• This is to prevent wear when it is first started
up after assembly.

GREASE
Y2-A106E

I-10
 GENERAL
TIGHTENING TORQUES

Hydraulic Hoses
Torque
UNION NUT
Hose Fitting Size Union Nut (G) Taper Thread (R)
N·m ft-lb N·m ft-lb
1/8 9.8 +4.9
0 7.3 +3.5
0 11.8 ±1.2 8.7 ±0.8
1/4 24.5 +4.9
18.1 +3.5
29.4 ±2.9 21.7 ±2.1 TAPER THREAD
0 0

3/8 49 +4.9
0 36.2 +3.5
0 53.9 ±5.4 39.8 ±3.9
+4.9 +3.5
1/2 58.8 0 43.4 0 88.3 ±8.8 65.1 ±6.4
3/4 117.7 +4.9
0 86.8 +3.5
0 147.1 ±14.7 108.5 ±10.7
Y2-A107E
+4.9 +3.5
1 137.3 0 101.3 0 196.1 ±19.6 144.7 ±14.3

Bite Type Pipe Fitting for Steel Pipe

Pipe Outer Diameter Torque
(mm) N·m ft-lb
8 34.3 ±4.9 25.3 ±3.5
10 41.7 ±2.5 30.7 ±1.7
12 58.8 ±4.9 43.4 ±3.5
15 88.3 ±4.9 65.1 ±3.5
16 93.2 ±4.9 68.7 ±3.5
18 132.4 ±4.9 97.6 ±3.5
22 205.9 ±9.8 151.8 ±7.2
27.2 245.2 ±9.8 181.0 ±7.2
28 313.8 ±19.6 231.4 ±14.3
32 313.8 ±19.6 231.4 ±14.3
35 411.9 ±19.6 303.7 ±14.3

I-11
 GENERAL

Joints for Piping

Nominal Thread Torque

Diameter Steel Cast Steel
(R) N·m ft-lb N·m ft-lb
1/8 11.8 ±1.2 8.7 ±0.8 10.8 ±1.1 8.0 ±0.7
1/4 29.4 ±2.9 21.7 ±2.1 24.5 ±2.5 18.1 ±1.7
3/8 53.9 ±5.4 39.8 ±3.9 49 ±4.9 36.2 ±3.5
1/2 88.3 ±8.8 65.1 ±6.4 73.5 ±7.4 54.3 ±5.3
3/4 147.1 ±14.7 108.5 ±10.7 127.5 ±12.7 94.1 ±9.3
1 196.1 ±19.2 144.7 ±14.3 171.6 ±17.2 126.6 ±12.5

Joints for Piping (O-ring Seal Type)

Nominal Thread Torque

Diameter
(G) N·m ft-lb
1/8 19.6 ±2.0 14.5 ±1.4
1/4 34.3 ±4.9 25.3 ±3.5
3/8 53.9 ±4.9 39.8 ±3.5
1/2 63.7 ±4.9 47.0 ±3.5
3/4 93.2 ±4.9 68.7 ±3.5
O-RING
1 107.9 ±9.8 79.5 ±7.2
1-1/4 117.7 ±9.8 86.8 ±7.2
1-1/2 137.3 ±9.8 101.2 ±7.2

Nominal Thread Torque

Diameter
(UNF) N·m ft-lb Y2-A110

7/16–20 16.7 ±2.0 12.3 ±1.4

1/2–20 22.6 ±2.0 16.6 ±1.4
9/16–18 31.4 ±2.9 23.1 ±2.1
3/4–16 59.8 ±4.9 44.1 ±3.5
1-1/16–12 102.0 ±5.9 75.2 ±4.4
1-5/16–12 135.3 ±7.8 99.8 ±5.8
1-5/8–12 181.4 ±9.8 133.8 ±7.2

I-12
 GENERAL

Bolts and Nuts (for ISO Strength Category 10.9)

Torque
Thread Size × Pitch General Tightening Points Special Tightening Points
N·m kgf·m ft-lb N·m kgf·m ft-lb
M6 × 1.0 9.8 ±0.5 1.0 ±0.05 7.2 ±0.4 11.8 ±0.6 1.2 ±0.06 8.7 ±0.4
M8 × 1.25 22.6 ±1.1 2.3 ±0.11 16.6 ±0.8 26.5 ±1.3 2.7 ±0.13 19.5 ±0.9
M10 × 1.5 47.1 ±2.4 4.8 ±0.24 34.7 ±1.7 54.9 ±2.7 5.6 ±0.28 40.5 ±2.0
Coarse M12 × 1.75 83.4 ±4.1 8.5 ±0.42 61.5 ±3.0 97.1 ±4.8 9.9 ±0.49 71.6 ±3.5
M14 × 2.0 134.4 ±6.7 13.7 ±0.68 99.1 ±4.9 155.9 ±7.7 15.9 ±0.79 115.0 ±5.7
M16 × 2.0 207.9 ±10.4 21.2 ±1.06 153.3 ±7.7 241.2 ±12.1 24.6 ±1.23 177.9 ±8.9
M20 × 2.5 410.9 ±20.5 41.9 ±2.09 303.1 ±15.1 475.6 ±23.7 48.5 ±2.42 350.8 ±17.5
M8 × 1.0 24.5 ±1.2 2.5 ±0.12 18.1 ±0.9 28.4 ±1.4 2.9 ±0.14 21.0 ±1.0
M10 × 1.25 50.0 ±2.5 5.1 ±0.25 36.9 ±1.8 58.8 ±2.9 6.0 ±0.30 43.4 ±2.2
M12 × 1.5 87.3 ±4.3 8.9 ±0.44 64.4 ±3.2 102.0 ±5.1 10.4 ±0.52 75.2 ±3.8
Fine
M14 × 1.5 135.3 ±6.8 13.8 ±0.69 99.9 ±5.0 157.9 ±7.8 16.1 ±0.80 116.5 ±5.8
M16 × 1.5 220.6 ±11.0 22.5 ±1.12 162.7 ±8.1 256.0 ±12.7 26.1 ±1.30 188.8 ±9.4
M20 × 1.5 452.1 ±22.6 46.1 ±2.30 333.4 ±16.6 524.7 ±26.1 53.5 ±2.66 387.0 ±19.2

1. General Tightening Points (Non-lubricated) 4. If tightening torque values are provided in this
• All securing points other than the special manual, then tightening should be done accord-
tightening points. ing to those values.
(This indicates that the tightening torque differs
2. Special Tightening Points (Grease with molyb- from the values given in this table.)
denum disulfide applied.)
• Points where particularly necessary due to 5. In order to tighten bolts and nuts evenly, they
function. should be tightened alternately top, bottom, left,
Special tightening positions and associated right.
instructions are given in the text.

3. Points where thread-locking compound is used

(Three Bond #1324 is applied.)
Thread-locking compound positions and associ-
ated instructions are given in the text.

I-13
II . SPECIFICATIONS

II-1
 SPECIFICATIONS

CONTENTS

Names of Components ............................................................................................................................................3

Dimensions .............................................................................................................................................................4
Machine Dimensions ........................................................................................................................................4
Operating Ranges .............................................................................................................................................5
Lifting Capacities ....................................................................................................................................................6
Specifications Tables ...............................................................................................................................................9
Specifications....................................................................................................................................................9
Specifications of Devices ...............................................................................................................................10
Mass Tables ...........................................................................................................................................................12
Unit Mass (Dry Mass) ....................................................................................................................................12
Recommended Lubricants ....................................................................................................................................13
Servicing Standards ..............................................................................................................................................14
Travel System .................................................................................................................................................14
Working Equipment........................................................................................................................................15
Standards for Judging Performance ......................................................................................................................16
Reference Value Table ....................................................................................................................................16
Mehhods for Inspecting Performance ....................................................................................................................... 18

In regard to Standard Values and Allowable Values

The terms used in the items “Servicing Standards” and “Standards for Judging Performance” have the following
meanings.

Standard Value ............ This indicates the standard value for the new machine at the time of shipping from the
factory. It should be used as the target value for maintenance work after operation.
Allowable Value .......... The dimensions of parts change during use because of wear and deformation. Also, the
performance of pumps, motors, and other hydraulic equipment drops, and this is the
estimated value indicating the use limit for the respective part. It is decided under refer-
ence to the standard at the time of shipping, the results of various tests, etc. As the use
conditions, the degree of repairs, etc., differ for each machine, these should be combined
and used as reference for servicing standards and standards for judging performance.
* Do not use the standard values and the allowable values as standards for customer
claims.

II-2
NAMES OF COMPONENTS SPECIFICATIONS
NAMES OF COMPONENTS

1. Canopy 12. Idler 23. Boom

2. Engine Hood 13. Track Roller 24. Boom Cylinder
3. Fuel Tank 14. Shoe Slide 25. Swing Bracket
4. Hydraulic Tank 15. Travel Motor 26. Swing Cylinder
5. Hydraulic Pump 16. Slew Bearing 27. Dozer Blade
6. Slew Motor 17. Track Adjuster 28. Dozer Blade Cylinder
7. Pilot Valve 18. Swivel Joint
8. Battery 19. Bucket
9. Control Valve 20. Bucket Cylinder
10. Engine 21. Arm
11. Crawler Belt 22. Arm Cylinder

II-3
BUY NOW
Then Instant Download
the Complete Manual
Thank you very much!