Compressors

Under supervision of Dr. Sameh Tawfeek

By: Mahmoud Mohamed Abdellatif
WHAT ARE COMPRESSORS ?

• Compressors are machines used to increase the total

energy level of a compressible fluid (either gas or
vapor).

• Molecular weight of compressed gas vary from 2

(Hydrogen) ~ 352 (uranium hexafluoride)
Main Types of Compressors
• The compressor is the heart of a mechanical refrigeration system.
• There is the need for many types of compressors because of the variety
of refrigerants and the capacity, location and application of the
systems.
• Generally, the compressor can be classified into two basic types:
positive displacement and Roto-dynamic.
 Advantages of Positive Displacement and Turbo-Compressors

Positive Displacement Turbo—compressors

➢ available for small and large capacities ➢ large capacities
➢ good rangeability ➢ Steady flow
➢ usually high efficiency ➢ relatively small dimensions
➢ suitable for light and heavy gases ➢ for large capacities
➢ little maintenance
➢ high reliability
➢ no oil contamination
➢ no valves
➢ low maintenance cost
➢ low wear
➢ low noise
➢ no severe vibration problems
➢ light foundation
 Disadvantages of Positive Displacement- and Turbo-Compressors

Positive Displacement Turbo—compressors

➢much maintenance required ➢not suitable for small capacities

➢low reliability ➢limited rangeability
➢often noisy (surge/stonewall)
➢often severe vibration problems ➢efficiency much dependent upon
good design and on operating
➢requires heavy foundation point
➢not suitable for very large ➢high compression ratio
capacities
➢difficult to obtain
➢less suitable for light gases
Reciprocating Compressor
 POSITIVE DISPLACEMENT COMPRESSORS

Positive Displacement Compressors, are machines in

which successive volumes of gas are confined within a
closed space where the pressure is increased as volume
of the closed space is decreased.
HOW RECIPROCATING COMPRESSORS
WORK ?

Reciprocating compressors are positive

displacement machines that compress and move
gases by using a combination of Rotational and
Linear (Reciprocating) motion

Ideal Reciprocating Compressor cycle as following:

➢ Suction
➢ Compression
➢ Discharge
➢ Expansion
 RECIPROCATING COMPRESSORS
CLASSIFICATION

Reciprocating compressors are available in:-

Single Acting (Trunk or automotive piston Type)
Double acting (Cross Head Type)
Trunk
Piston
Cylinder
Volume

Head-End Crank-End
Cylinder Cylinder Rod Connecting
Volume Volume Packing Rod

Crank

Piston Piston Cross

Rod Head
Principle of Operation

Line 4-1:
Discharge
volume

The suction valve opens at point 4. 3 2

As the piston travels toward the
bottom dead center, the volume of the
cylinder increases and the vapor pressure

flows into the cylinder. Clearan

ce Suction intake volume

1
The pressure inside the cylinder is 4

slightly less than suction line Piston displacement

pressure. The pressure difference Total cylinder volume

pushes the valve open on during the

volume
suction stroke.
Principle of Operation

Line 1-2:
Discharge
volume
The suction valve returns to close under
3 2
the spring force as the vapor pressure
across the valve is equalized when the
piston has reached the bottom dead center.
pressure

The piston then changes the moving Clearan

ce Suction intake volume
direction at point 1. The cylinder volume
decreases as the piston moves towards the 4 1

top dead center, raising the pressure inside Piston displacement

the cylinder. Total cylinder volume

The shape of the compression line (Line volume

1-2) is determined by the properties of the
refrigerant and the compression exponent.
Principle of Operation

Line 2-3: Discharge

volume

At point 2, the pressure inside the cylinder has 3 2

become slightly greater than discharge line
pressure.
pressure
This causes the valve opening allowing the gas
to flow out of the cylinder. Clearan
ce Suction intake volume

The volume continues to decrease toward point 4 1

3, maintaining a sufficient pressure difference
Piston displacement
across the discharge valve to hold it open.
Total cylinder volume

volume
Principle of Operation
Line 3-4:
At point 3, the piston reaches the top dead center
and reverses direction.
At top dead center, as the piston comes to a Discharge
volume
complete stop prior to reversing direction, the 3 2
pressure across the valve is equal.
So, the discharge valve is closed.
As the piston moves towards point 4, the volume
increases and the pressure decreases in the pressure
cylinder.
Clearan
The gas trapped in the cylinder expands as the ce Suction intake volume

volume increases until to point 4.

4 1
At point 4, the gas pressure inside the cylinder
becomes less than the suction line pressure, so Piston displacement

the suction valve opens again. Total cylinder volume

The cycle then starts over again.

The shape of the re-expansion line (Line 3-4) is volume
dependent on the same compression exponent
that determines the shape of the compression
line.
 3. Clearance Space and Clearance Fraction
 In order to prevent the piston from striking the valve plate, a clearance
volume must be allowed at the end of the piston compression stroke.

 Manufacturing design tolerances require this to allow for reasonable bearing

wear, which would effectively lengthen the stroke.

 The space between the bottom and top of the valve assembly adds extra to
the clearance volume.

17
 The clearance volume will cause the vapor not being completely discharged
after compression.
 The remaining vapor trapped in the clearance volume will re-expend in the
next suction stroke.
 As a result, the volume of the vapor sucked in by the compressor in each
stroke is less than the volume the piston swept through.
 So the compressor volumetric displacement must be greater than the volume
of vapor to be drawn in.
 Other factors that cause reduction to the compressor capacity are:
 pressure drop through valves which reduces the amount of vapor sucked or
discharged; vapor leaks around closed valves or between the piston and
cylinder; refrigerant evaporating out of oil in the cylinder space; the vapor
heated by the cylinder walls, thus, increasing its specific volume.
 The performance of reciprocating compressors can be described by
volumetric efficiency.
 Here we only consider the actual and the clearance volumetric efficiencies.
The actual volumetric efficiency is defined as

volume  flow  rate  entering  compressor , m3 s

va 
displacement  rate  of  compressor , m3 s
Effect of Compression Ratio and Volume Clearance % on Volumetric Efficiency
Screw Compressor
The Construction and operation of Screw Compressors

 Screw compressors are also

belong to the positive
displacement compressor family.
 In screw compressors, the
compression is accomplished by
the enmeshing of two mating
helically grooved rotors suitably
housed in a cylinder equipped
with appropriated inlet and
discharge ports.
 The rotors are the main components of the screw
compressor.
 A cross view of the two principle rotating elements
of the screw compressor is shown in Fig.
 The male rotor is normally the driving rotor and
consists of a series of lobes (usually four) along the
length of the rotor that mesh with similarly formed
corresponding helical flutes (usually six) on the
female rotor.
 As the rotors turn, vapor is drawn through the inlet
opening to fill the space between the male lobe and
the female flute.

 As the rotors continue to rotate, the vapor is moved

past the suction port and sealed in the interlobe space.

 The vapor so trapped in the interlobe space is moved

both axially and radially and is compressed by direct
volume reduction as the enmeshing of the lobes
progressively reduced the space occupied by the vapor.
 Compression of the vapor continues until the interlobe
space communicates with the discharge ports in the
cylinder and the compressed vapor leaves the cylinder
through these ports.

 The length and diameter of the rotors determine the

capacity and the discharge pressure.

 The longer the rotors, the higher the pressure.

 The larger the diameter of the rotors, the greater the

capacity.
Advantages of the screw compressor

 Screw compressors are reliable and compact.

 Compressor rotors can be manufactured with very small clearances at an economic cost.
 In many applications, the screw compressor offers significant advantages over reciprocating
compressors.
1. Its fewer moving parts mean less maintenance. There is no need to service the items such as
compressor valves, packing and piston rings, and the associated downtime for replacement.

2. The absence of reciprocating inertial forces allows the screw compressor to run at high speeds. So, it
could be constructed more compact.
 3. The continuous flow of cooling lubricant allows much higher single-stage compression ratios.

4. The compactness tends to reduce package costs.

5. Low vibration due to reducing or eliminating pulsations by screw technology

6. Higher speeds and compression ratios help to maximize available production horsepower.

 A major problem with screw compressors is that the pressure difference between entry and
exit creates very large radial and axial forces on the rotors whose magnitude and direction is
independent of the direction of rotation.
Sliding Vane Compressor
Vane Type Compressors
• The vane type compressor，which is also
called as “sliding vane compressor”or “multi-
vane compressor” by some companies,
employs a series of rotating vanes or blades
which are installed equidistant around the
periphery of a slotted rotor
 The rotor shaft is mounted eccentrically in a
steel cylinder so that the rotor nearly touches
the cylinder wall on one side, the two being
separated only by an oil film at this point.
 Directly opposite this point the clearance
between the rotor and the cylinder wall is
maximum.
 Heads or end-plates are installed on the ends
of the cylinder and to hold the rotor shaft.
Vane Type Compressors
• The vanes move back and forth radially in the rotor
slots as they follow the contour of the cylinder wall
when the rotor is turning.
• The vanes are held firmly against the cylinder wall
by action of the centrifugal force developed by the
rotating rotor.
• In some instances, the blades are spring-loaded to
obtain a more positive seal against the cylinder wall.
 The suction vapor drawn into the cylinder through
suction ports in the cylinder wall is entrapped
between adjacent rotating vanes.
 The vapor is compressed by the reduction in
volume that results as the vanes rotate from the
point of maximum rotor clearance to the point of
minimum rotor clearance.
 The compressed vapor is discharged from the
cylinder through ports located in the cylinder wall
near the point of minimum rotor clearance.
• The discharge ports are so located as to allow discharge of the
compressed vapor at the desired point which is the design point of
the compressor during the compressing process.
• Operation of the compressor at compression ratios above or below
the design point will result in compression losses and increasing
power consumptions.
• Current practice limits compression ratios to a maximum of 7 to 1.
2- Sliding Vane Compressors
A

A Compressor Cover Side View

• Sliding vane compressors are positive displacement
compressors.
• Sliding vane compressors are similar to Reciprocating
compressors.
• they have relatively lower capacity lower discharge pressure
compared with other types of compressors(centrifugal, axial
or reciprocating, screw respectively).
• Vane compressor can be used to 50 psi in single stage form
and 125 psi in multi-stage form
• Often operate as pre-compressors or booster compressors.
• They exist as single stage or even three-stage system with
inter-coolers.
• The vanes must travel fast enough to seal against the
cylinder wall but not so fast that they cause excessive wear.
• The vane number influences the differential pressure
between adjacent vane cells. This influence becomes less as
the number of vanes increases
• Rolling element bearings are widely used, generally the
roller type.
• Seals are either a packing or mechanical contact type.
• Packing and bearings are lubricated by a pressurized system.
Centrifugal Compressor
The construction and operation of turbo
Compressors
 Vapor enters axially at the center wheel
1 and flows through the passage 3 in the
impeller 2.
 The pressure and absolute velocity of
the vapor rises when it passes the
impeller because of the centrifugal
force.
 In the stationary diffuser 4 the flow of
vapor is decelerated to further raise the
vapor pressure.
 The compressed vapor is collected in
the scroll or volute 5 and discharged to
the delivery pipe 6.
Different types of Impellers
 1- GAS INITIAL CONDITION AT INLET

2- GAS AFTER ACCELERATION

2

3 3- GAS AFTER DECELERATION

1
Single Stage Centrifugal compressor
Multistage Centrifugal Compressor
Axial Flow Compressors
• Axial compressors are rotating, aero foil based compressors in which
the working fluid principally flows parallel to the axis of rotation. This
is in contrast with centrifugal and mixed‐flow compressors where the
air may enter axially but will have a significant radial component on
exit.
• One stage comprises a row of rotor blades followed by row of stator
vanes
• A no. of such stages with rotors on a common shaft form the
compressor
 PRINCIPLE OF OPERATION

The rotor blades increase the gas velocity.

The velocity is then converted into
pressure as the gas enters the stator
section and is slowed down.
As the pressure is increased through the
successive sets of rotors and stators, the
volume decreases, as does the area of the
rotor and stator blades.
 Axial Flow Compressor Pressure

Velocity

Pressure

Stator Rotor Stator Rotor Stator

27 November 2017 52
AIR IN COMPRESSOR STAGES

STATOR STATOR
BLADES BLADES

FIXED FIXED