Heat Transfer Chap03 - Lecture

Chapter 3
STEADY HEAT CONDUCTION

Objectives
• Understand the concept of thermal resistance and its
limitations, and develop thermal resistance networks for
practical heat conduction problems
• Solve steady conduction problems that involve multilayer
rectangular, cylindrical, or spherical geometries
• Develop an intuitive understanding of thermal contact
resistance, and circumstances under which it may be
significant
• Identify applications in which insulation may actually
increases thermal resistance
• finned surfaces, and assess how efficiently and effectively
fins enhance heat transfer
2
STEADY HEAT CONDUCTION IN PLANE WALLS
Heat transfer through the wall of a house can be
modeled as steady and one-dimensional.
The temperature of the wall in this case depends
on one direction only (say the x-direction) and
can be expressed as T(x).
for steady operation

In steady operation, the rate of heat transfer
through the wall is constant.
Fourier’s law of
heat conduction
3
The rate of heat conduction through
a plane wall is proportional to the
average thermal conductivity, the
wall area, and the temperature
difference, but is inversely
proportional to the wall thickness.
Once the rate of heat conduction is
available, the temperature T(x) at
any location x can be determined by
Under steady conditions, the
replacing T2 by T, and L by x.
temperature distribution in a plane
wall is a straight line: dT/dx = const.
4
Thermal Resistance Concept
Conduction resistance of the

wall: Thermal resistance of the
wall against heat conduction.
Thermal resistance of a medium Analogy between thermal and electrical
depends on the geometry and the resistance concepts.
thermal properties of the medium.
rate of heat transfer  electric current
thermal resistance  electrical resistance
Electrical resistance temperature difference  voltage difference
5
Newton’s law of cooling
Convection resistance of the

surface: Thermal resistance of the
surface against heat convection.
Schematic for convection resistance at a surface.
When the convection heat transfer coefficient is very large (h → ),

the convection resistance becomes zero and Ts  T∞.
That is, the surface offers no resistance to convection, and thus it
does not slow down the heat transfer process.
This situation is approached in practice at surfaces where boiling
and condensation occur. 6
Radiation resistance of the
surface: Thermal resistance of the
surface against radiation.
Radiation heat transfer coefficient
Combined heat transfer

coefficient
Schematic for
convection and radiation
7
resistances at a surface.
Thermal Resistance Network
The thermal resistance network for heat transfer through a plane wall subjected to
convection on both sides, and the electrical analogy.
8
Temperature drop
U overall heat
transfer coefficient
Once Q is evaluated, the

surface temperature T1 can
be determined from
The temperature drop across a layer is

proportional to its thermal resistance.
9
Multilayer
Plane
Walls
The thermal resistance
network for heat transfer
through a two-layer plane
wall subjected to
convection on both sides.
10
11
THERMAL CONTACT RESISTANCE
Temperature distribution and heat flow lines along two solid plates
12
pressed against each other for the case of perfect and imperfect contact.
• When two such surfaces are pressed
against each other, the peaks form good
material contact but the valleys form voids
filled with air.
• These numerous air gaps of varying sizes
act as insulation because of the low
thermal conductivity of air.
• Thus, an interface offers some resistance
to heat transfer, and this resistance per
unit interface area is called the thermal
contact resistance, Rc.
13
The value of thermal
contact resistance
hc thermal contact depends on:
conductance • surface roughness,
• material properties,
• temperature and
pressure at the
interface
• type of fluid trapped
at the interface.
Page 139
thermal contact resistance is significant and can even dominate the

heat transfer for good heat conductors such as metals, but can be
disregarded for poor heat conductors such as insulations. 14
The thermal contact resistance can
be minimized by applying
• a thermal grease such as silicon oil
• a better conducting gas such as
helium or hydrogen
• a soft metallic foil such as tin, silver, Effect of metallic coatings on
thermal contact conductance 15
copper, nickel, or aluminum
The thermal contact conductance is highest (and thus the contact
resistance is lowest) for soft metals with smooth surfaces at high pressure. 16
GENERALIZED THERMAL RESISTANCE NETWORKS
Thermal resistance network for two parallel layers.

17
Two assumptions in solving complex
multidimensional heat transfer
problems by treating them as one-
dimensional using the thermal
resistance network are
(1) any plane wall normal to the x-axis is
isothermal (i.e., to assume the
temperature to vary in the x-direction
only)
(2) any plane parallel to the x-axis is
adiabatic (i.e., to assume heat transfer Thermal resistance network for
to occur in the x-direction only) combined series-parallel
Do they give the same result? 18
arrangement.
HEAT CONDUCTION IN CYLINDERS AND SPHERES
Heat transfer through the pipe
can be modeled as steady
and one-dimensional.
The temperature of the pipe
depends on one direction only
(the radial r-direction) and can
be expressed as T = T(r).
The temperature is
independent of the azimuthal
angle or the axial distance.
This situation is approximated
in practice in long cylindrical
Heat is lost from a hot-water pipe to
pipes and spherical
the air outside in the radial direction,
containers.
and thus heat transfer from a long
pipe is one-dimensional.
19
A long cylindrical pipe (or spherical
shell) with specified inner and outer
surface temperatures T1 and T2.
Conduction resistance of the cylinder layer

20
A spherical shell
with specified
inner and outer
surface
temperatures T1
and T2.
Conduction resistance of the spherical layer

21
for a cylindrical layer
for a spherical layer

network for a cylindrical (or
spherical) shell subjected
to convection from both the
inner and the outer sides.
22
Multilayered Cylinders and Spheres

network for heat transfer
through a three-layered
composite cylinder
subjected to convection
on both sides.
23
Once heat transfer rate Q has been
calculated, the interface temperature
T2 can be determined from any of the
following two relations:
24
CRITICAL RADIUS OF INSULATION
Adding more insulation to a wall or
to the attic always decreases heat
transfer since the heat transfer area
is constant, and adding insulation
always increases the thermal
resistance of the wall without
increasing the convection
resistance.
In a a cylindrical pipe or a spherical
shell, the additional insulation
increases the conduction
resistance of the insulation layer
but decreases the convection An insulated cylindrical pipe exposed to
resistance of the surface because convection from the outer surface and
of the increase in the outer surface the thermal resistance network
area for convection. associated with it.
The heat transfer from the pipe
may increase or decrease,
depending on which effect
dominates. 25
The critical radius of insulation
for a cylindrical body:
(P153E )
The critical radius of insulation

for a spherical shell:
The largest value of the critical

radius we are likely to
encounter is p-161
We can insulate hot-water or

steam pipes freely without
worrying about the possibility of The variation of heat transfer
increasing the heat transfer by rate with the outer radius of the
insulating the pipes. 26
insulation r2 when r1 < rcr.
HEAT TRANSFER FROM FINNED SURFACES
Newton’s law of cooling: The rate of heat transfer
from a surface to the surrounding medium
When Ts and T are fixed, two ways to
increase the rate of heat transfer are
• To increase the convection heat transfer
coefficient h. This may require the
installation of a pump or fan, or replacing
the existing one with a larger one, but this
approach may or may not be practical.
Besides, it may not be adequate.
• To increase the surface area As by
attaching to the surface extended surfaces
called fins made of highly conductive
materials such as aluminum.
27
The thin plate fins of a car
radiator greatly increase the
rate of heat transfer to the air.
28
Fin Efficiency
29
Zero thermal resistance or infinite
thermal conductivity (Tfin = Tb)
30
Summary
• Steady Heat Conduction in Plane Walls
 Thermal Resistance Concept
 Thermal Resistance Network
 Multilayer Plane Walls
• Thermal Contact Resistance
• Generalized Thermal Resistance Networks
• Heat Conduction in Cylinders and Spheres
 Multilayered Cylinders and Spheres
• Critical Radius of Insulation
• Heat Transfer from Finned Surfaces
 Fin Equation
 Fin Efficiency
 Fin Effectiveness
 Proper Length of a Fin
• Heat Transfer in Common Configurations
31

Heat Transfer Chap03 - Lecture

Uploaded by

Copyright:

Available Formats

Heat Transfer Chap03 - Lecture

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Heat Transfer Chap03 - Lecture

Uploaded by

Copyright:

Available Formats

Chapter 3

STEADY HEAT CONDUCTION

for steady operation

Conduction resistance of the

Convection resistance of the

Schematic for convection resistance at a surface.

When the convection heat transfer coefficient is very large (h → ),

Radiation heat transfer coefficient

Combined heat transfer

Once Q is evaluated, the

The temperature drop across a layer is

thermal contact resistance is significant and can even dominate the

Thermal resistance network for two parallel layers.

Conduction resistance of the cylinder layer

Conduction resistance of the spherical layer

for a spherical layer

The thermal resistance

The critical radius of insulation

The largest value of the critical

We can insulate hot-water or

You might also like