CTQIUV05

Universal Wireless
Charging Solution

IN THE KIT
• Mounting Frame • Tap Splices (x4)
• Anti-Skid Mat • Fibre Optice Cable (300mm)
• Charging Subsystem • Fibre Optic Mount Accessories
• Connection Cable • Double Sided Tape (x2)

ABOUT THIS PRODUCT

The CTQIUV05 is a universal, retrofit solution which enables Qi certified, wireless charging within
your vehicle. With the installation of this wireless charging pad, you are able to benefit from 15W
charging power for your selected Qi compatible device/smartphone.

FEATURES
• Qi Certified product
• Easy to install
• Gain Qi wireless charging in your vehicle (for compatible devices)
• Integrates seamlessly with the factory storage tray

The “Qi” symbol is a trademark of the “Wireless Power Consortium”.

DISCLAIMER
The information provided in this document is subject to change without notice due to manufacturer changes and/or improvements to the product/s. This
instruction manual is based on documented data and research. The manufacturer of this product cannot be held responsible for any changes made to the
vehicle by the manufacturer or damages that may occur through the installation of this product in accordance with the steps outlined herein.

CTQIUV05_v1
PRIOR TO INSTALLATION
Read the manual prior to installation. Technical knowledge is necessary for installation. The place of installation must be
free of moisture and away from heat sources. Please ensure that the correct tools are using during the installation to avoid
damage to the vehicle or product. Connects2 can not be held responsible for the installation of this product.

INSTALLATION GUIDE
The installation of the CTQIUV05 is easy, straightforward, and versatile for any consumers needs, however,
placement of the unit is key. Below is a diagram of how the CTQIUV05 pieces together.
Please note: if installing under a vehicle’s surface, the maximum distance between the ‘charging subsystem’ and the
‘anti-skid mat’ is 5mm. There must be no metal placed between the charging coil and the smartphone.

Anti-Skid Mat
Charging
Subsystem

Fibre Optic LED

(optional)

Double-Sided
Tape

Mounting
Frame

INTEGRATED FOREIGN OBJECT DETECTION (FOD)

IMPORTANT INFORMATION:
Please don‘t place any metallic objects such as coins, keys, credit cards etc. onto the CTQIUV05 surface - especially
smartphones with attached ring stand holder - otherwise the integrated ‘Foreign Object Detection‘ (FOD) will interrupt
the wireless charging process for safety reasons.

CARD
xxxx xxxx xxx

!
2 CTQIUV05_v1
INSTALLATION GUIDE

1
Begin by placing the charging subsystem
into the mounting frame. Make sure that
orientation is correct so that the power
supply connection is easily accessible
within the cut-out of the mounting frame
(circled).

2 Utilising the double-sided tape, attach to

both sides of the mounting frame.
Once the placement has been decided,
proceed to stick the frame combination
up against the vehicle dash/area utilising
the double-sided tape again. On the
external surface, you will then need to
place the anti-skid mat.

Please note: max distance between ‘charging

subsystem’ and the ‘anti-skid mat’ is 5mm.
There must be no metal placed between the
charging coil and the smartphone.

Now take the power connection cable

from within the kit and attach the 2-pin
connector to the subsystem as shown.
Note that this step can be taken either
before or after mounting the frame to the
vehicles surface.

Need help? Visit support.connects2.com/tickets/technical

3 CTQIUV05_v1
INSTALLATION GUIDE
4
Locate both a source of +12V switched
as well as a source of Ground near to the
charging unit. Take a set of ‘tap splices’
and simply snap them over the wiring.

Please note: dependent on the sizing of the

vehicles wiring, there are two different sizes
of tap splices provided. Simply utilise the
needed blade depth and disregard the others.

Ø 1.5mm² <|> Ø 2.5mm²

+12V switched
With both tap splices attached securely,
grab the power connection cable and
push both the spade connections here
onto the relevant tap splice spines.
Ensure that the 12V wire goes onto the
12V tap splice and the Ground wire to the
Ground tap splice.

- GND

4 CTQIUV05_v1
INSTALLATION GUIDE
The following steps surrounding the fitment of a fibre optic dashboard LED are optional and aren’t fully required
for the correct functionality of the CTQIUV05. Feel free to place any of the fibre optic components in storage.
Note: fitment of the LED does require modification/cutting of the dashboard.

Take the fibre optic mounting plate and

attach it to the 2x prongs on the side of
the mounting frame. With the mounting
plate attached, simply line up the 300mm
length of fibre optic filament to the
circular aperture on the mount and bond
it via means of a transparent adhesive
(not provided).

7
Surface of vehicle Guide the fibre optic filament toward the
surface of the vehicle. Attach the black
coupling grommet to the end of the
300mm length of fibre optic filament and
on the other end, you will need to place
the smaller length of filament (19.1mm).
From here, you will need to drill a 2.9mm
hole in the dashboard, this will allow the
smaller length of fibre optic filament to
protrude out through the dashboard.

With the fibre optic LED installed correctly, you will be able to visually tell the status of the CTQIUV05.
Dependent on it’s condition, the unit will display one of the following:
START
- Standby / ACC STOP

- Wireless Charging in Progress

- Phone fully charged (dependent on phone) 100%

- Detection of foreign object(s) (FOD - see
page 2.) on charging pad. Charging process
stopped for safety reasons.

Please ensure all due care is taken when modifying the vehicle. Connects2 promotes the aid of professional
installers and will not be held liable for damage due to improper installation.

Need help? Visit support.connects2.com/tickets/technical

5 CTQIUV05_v1
PRODUCT INFORMATION

165.3 mm

76mm
135mm

Maximum distance (including anti-skid mat): 5mm Anti-skid mat Surface in vehicle

MAX
5mm 17.9mm

Input Voltage 12V (DC)

Output Voltage 5V 9V 9V
Output Current 1.1A 1.2A 1.6A
Output Power 5W 10W 15W

+12V

!
5A / 60W MAX

PLEASE NOTE: After installation of the wireless charging device, other devices that
use more than 5A / 60W should not be operated via the +12V socket. Otherwise a
risk of overvoltage can occur!

6 CTQIUV05_v1
NOTES

Need help? Visit support.connects2.com/tickets/technical

7 CTQIUV05_v1
NOTES

8 CTQIUV05_v1