TLP250

TOSHIBA Photocoupler GaAAs Ired & PhotoIC

TLP250
Transistor Inverter Inverter For Air Conditioner IGBT Gate Drive Power MOS FET Gate Drive
The TOSHIBA TLP250 consists of a GaAlAs light emitting diode and a integrated photodetector. This unit is 8lead DIP package. TLP250 is suitable for gate driving circuit of IGBT or power MOS FET. Input threshold current: IF=5mA(max.) Supply current (ICC): 11mA(max.) Supply voltage (VCC): 1035V Output current (IO): 1.5A (max.) Switching time (tpLH/tpHL): 0.5s(max.) Isolation voltage: 2500Vrms(min.) UL recognized: UL1577, file No.E67349 Option(D4) VDE Approved : DIN EN60747-5-2 Maximum Operating Insulation Voltage : 890VPK Highest Permissible Over Voltage Please designate Option(D4)
1 2 8 7 6 5

Unit in mm

TOSHIBA 1110C4 Weight: 0.54 g(Typ.)

: 4000VPK

(Note):When a EN60747-5-2 approved type is needed,

Pin Configuration (top view)

Truth Table
Tr1 Input LED On Off On Off Tr2 Off On

3 4

1 : N.C. 2 : Anode 3 : Cathode 4 : N.C.

5 : GND 6 : V O (Output) 7 : VO 8 : VCC

Schmatic
IF 2+ VF 3-

I CC VCC 8 (Tr 1) 7 IO (Tr 2) 6 VO VO

GND A 0.1F bypass capcitor must be connected between pin 8 and 5 (See Note 5). 5

2007-10-01

TLP250
Absolute Maximum Ratings (Ta = 25C)
Characteristic Forward current Forward current derating (Ta 70C) LED Peak transient forward curent Reverse voltage Junction temperature Hpeak output current (PW 2.5s,f 15kHz) Lpeak output current (PW 2.5s,f 15kHz) Output voltage Detector Supply voltage Output voltage derating (Ta 70C) Supply voltage derating (Ta 70C) Junction temperature Operating frequency Operating temperature range Storage temperature range Lead soldering temperature (10 s) Isolation voltage (AC, 1 min., R.H. 60%) (Note 4) (Note 3) (Note 2) (Note 2) (Ta 70C) (Ta = 85C) (Ta 70C) (Ta = 85C) (Note 1) Symbol IF IF / Ta IFPT VR Tj IOPH IOPL VO VCC VO / Ta VCC / Ta Tj f Topr Tstg Tsol BVS Rating 20 0.36 1 5 125 1.5 +1.5 35 24 35 24 0.73 0.73 125 25 20~85 55~125 260 2500 Unit mA mA / C A V C A A V V V / C V / C C kHz C C C Vrms

Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (Handling Precautions/Derating Concept and Methods) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). Note 1: Note 2: Note 3: Note 4: Note 5: Pulse width PW 1s, 300pps Exporenential wavefom Exporenential wavefom, IOPH 1.0A( 2.5s), IOPL +1.0A( 2.5s) Device considerd a two terminal device: Pins 1, 2, 3 and 4 shorted together, and pins 5, 6, 7 and 8 shorted together. A ceramic capacitor(0.1F) should be connected from pin 8 to pin 5 to stabilize the operation of the high gain linear amplifier. Failure to provide the bypassing may impair the switching proparty. The total lead length between capacitor and coupler should not exceed 1cm.

Recommended Operating Conditions

25

Note: Recommended operating conditions are given as a design guideline to obtain expected performance of the device. Additionally, each item is an independent guideline respectively. In developing designs using this product, please confirm specified characteristics shown in this document. Note 6: Input signal rise time(fall time)<0.5s.

2007-10-01

TLP250
Electrical Characteristics (Ta = 20~70C, unless otherwise specified)
Characteristic Input forward voltage Temperature coefficient of forward voltage Input reverse current Input capacitance H level Output current L level H level Output voltage L level VOL 4 IOPL VOH 2 3 Symbol VF VF / Ta IR CT IOPH Test Cir cuit 1 Test Condition IF = 10 mA , Ta = 25C IF = 10 mA VR = 5V, Ta = 25C V = 0 , f = 1MHz , Ta = 25C VCC = 30V (*1) IF = 10 mA V86 = 4V IF = 0 V65 = 2.5V Min 0.5 0.5 11 0.8 10 VS = 0 , f = 1MHz Ta = 25 VS = 500V , Ta = 25C R.H. 60% 110
12

Typ.* 1.6 2.0 45 1.5 2 12.8 14.2 7 7.5 1.2 1.0 10

Max 1.8 10 250

Unit V mV / C A pF

A V 12.5 11 11 5 35 2.0 mA V V pF mA

VCC1 = +15V, VEE1 = 15V RL = 200, IF = 5mA VCC1 = +15V, VEE1 = 15V RL = 200, VF = 0.8V VCC = 30V, IF = 10mA Ta = 25C VCC = 30V, IF = 10mA

H level Supply current L level Threshold input current Threshold input voltage Supply voltage Capacitance (inputoutput) Resistance(inputoutput) Output LH Output HL

ICCH

ICCL

VCC = 30V, IF = 0mA Ta = 25C VCC = 30V, IF = 0mA

IFLH

VCC1 = +15V, VEE1 = 15V RL = 200, VO > 0V VCC1 = +15V, VEE1 = 15V RL = 200, VO < 0V

VFHL
VCC CS RS

* All typical values are at Ta = 25C

(*1): Duration of IO time 50s

2007-10-01

TLP250
Switching Characteristics (Ta = 20~70C , unless otherwise specified)
Characteristic Propagation delay time Output rise time Output fall time Common mode transient immunity at high level output Common mode transient immunity at low level output LH HL Symbol tpLH tpHL tr tf CMH 6 CML VCM = 600V, IF = 0mA VCC = 30V, Ta = 25C 5000 V / s VCM = 600V, IF = 8mA VCC = 30V, Ta = 25C 5 IF = 8mA VCC1 = +15V, VEE1 = 15V RL = 200 Test Cir cuit Test Condition Min 5000 Typ.* 0.15 0.15 Max 0.5 0.5 V / s s Unit

All typical values are at Ta = 25C

Test Circuit 1 : IOPH 8 1 VCC 0.1F IF A 4 IOPH V8-6

Test Circuit 2 : IOPL 8 1 0.1F A 4 IOPL V6-5 VCC

Test Circuit 3 : VOH 8 1 VCC1 0.1F IF RL V VOH 4

Test Circuit 4 : VOL 8 1 0.1F VF V 4 VEE1 RL VOL VCC1

VEE1

2007-10-01

TLP250
Test Circuit 5: tpLH, tpHL, tr tf 8 IF 0.1F VO RL VO VCC1 IF tr

tf VOH GND VOL 80% 80%

100

tpLH VEE1

tpHL

Test Circuit 6: CMH, CML 8 1 SW A IF B VO 4 VCM + 0.1F VCC

600V VCM 90% 10% tr tf

SW :A(IF=8mA) CMH VO SW :B(IF=0) 3V 26V CHL

CML = 480 (V) tr (s) CMH = 480 (V) tf (s)

CML(CMH) is the maximum rate of rise (fall) of the common mode voltage that can be sustained with the output voltage in the low (high) state.

2007-10-01

TLP250

IF V F
100 50 30 Ta = 25 C -2.6

VF / Ta IF

Forward voltage temperature coefficient VF / Ta (mV / C)

-2.4

(mA)

10 5 3 1 0.5 0.3 0.1 0.05 0.03 0.01 1.0 1.2 1.6

-2.2

Forward current IF

-2.0

-1.8

-1.6

-1.4 0.1

0.3 0.5

10

30

Forward voltage

VF (V)

Forward current

IF (mA)

IF Ta
40 40

VCC Ta

Allowable forward current IF (mA)

20

Allowable supply voltage VCC

30

(V)
30 20 10 10 0 0 0 0

40

60

80

100

20

40

60

80

100

Ambient temperature Ta (C)

Ambient temperature Ta (C)

IOPH, IOPL Ta
PW 2.5 s, f 15 KHz

Allowable peak output current IOPH, IOPL (A)

0 0

20

40

60

80

100

Ambient Temperature Ta (C)

2007-10-01

TLP250

RESTRICTIONS ON PRODUCT USE

20070701-EN

TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the Handling Guide for Semiconductor Devices, or TOSHIBA Semiconductor Reliability Handbook etc. The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (Unintended Usage). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customers own risk. The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. GaAs(Gallium Arsenide) is used in this product. The dust or vapor is harmful to the human body. Do not break, cut, crush or dissolve chemically. Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations.

2007-10-01