Sandvik DE130

compact core drill

Technical specification Type Fully hydraulic core drill

The DE130 has proven itself in a number of field applica- Rotation unit Drill head with chuck
tions to be the most reliable and economic drill for the Feed force 46,1 kN 10 350 lbf
general drilling contractor or mine, in both surface and Pull force 61,5 kN 13 820 lbf
underground applications. Over the years a number of re- Depth 1 200 m (B) 3 936 ft (B)
designs, modifications, improvements and adaptations to capacity, max
various applications have taken place. This process goes on Feed length* 1 700 mm 5’7’’
continuously in cooperation between manufacturer and Weight 510 kg* 1 125 lb*
user. A large number of options are available to match the (including feed boom, 560 kg** 1 235 lb**
most varied drilling conditions. drill head 77 mm, rod

holder and wall bracket)

* Underground version
**Surface version
Depth capacity

Depth capacity vertical down

“N”-head “H”-head
WL 46 mm 1 200 m (3 936 ft) Not suited
A 1 000 m (3 280 ft) Not suited
WL 56 mm 1 200 m (3 936 ft) 1 200 m (3 936 ft)
B 800 m (2 624 ft) 800 m (2 624 ft)
WL 66 mm 800 m (2 624 ft) 800 m (2 634 ft)
N 600 m (1 968 ft) 600 m (1 968 ft)
WL 76 mm 700 m (2 296 ft) 700 m (2 296 ft)
H Not suited 400 m (1 312 ft)

All capacity indications are given without any guaranty but

could be expected in “normal” ground conditions by a
well-trained drilling crew using high quality drilling tools.
Practical up-drilling capacity is about 50% of capacity in
holes vertical down.

Basic drill
Feed boom
Standard version is made of very stiff and torsion resistant
aluminium profile. The feed boom is mounted on a frame
with hydraulic tilt cylinder and mechanical supports.
The mounting frame for the underground version is spe-
cially designed for easy setting-up when fan drilling and has
a full range adjustment from vertical down to vertical up.
Positioning is simplified by a mechanical feed boom
positioner allowing a telescoping of 1 - 2 m (3 - 6’)
depending on feed boom length.

Basic facts
Feed length (underground) 1 700 mm (5’7’’)
Total length (underground) 3 065 mm (10’)
Feeding force 46,1 kN (10 350 lbf)
Pulling force 61,5 kN (13 820 lbf) Feed boom
Feed rate, drilling max 0,04 m/s (1,5’’/s)
Feed rate, rod running, max 1,1 m/s (43’’/s)
Practical rod running speed 20 m/min (60’/min)
Rotation unit
Rotation unit
Drill head with chuck
Drive spindle inner High gear
diameter 77 mm (3”) - 178 Nm at 1600 rpm (137 lbf ft)
- 550 Nm at 565 rpm (427 lbf ft)
Torque
Low gear
- 259 Nm at 1100 rpm (200 lbf ft)
- 800 Nm at 390 rpm (619 lbf ft)
Number of jaws 8
Gripping range 30-76 mm (1 3/16’’-3’’)
Gripping range, 10 mm (3/8’’)
set of jaws

Speed, infinitely variable 0-2000 rpm. Clamping by spring

action, opened hydraulically. Exchangeable rod guide and
jaws for standard drill rods and casings.
Rod holder
Clamping by accumulator action, opened hydraulically.
Exchangeable rod guide and jaws for standard drill rods,
casings and core barrels.

Basic facts
Number of jaws 2 Rod holder
Gripping range 30-106 mm (1 3/16’’-4 1/8’’)
Gripping range, 20 mm (3/4’’)
set of jaws
Max opening, 136 mm (5 5/16’’)
without jaws

Control panel

Basic facts
Type Central control of all drilling
operations, including flush Control panel
pump, wireline hoist and Standard
boom tilt
Gauges for: - hydraulic system pressure
- feeding force
- water pressure
- water flow

Power unit

Basic facts
Max working Power unit
250 bar (3 625 psi) Surface
pressure
Max oil flow 142-174 l/min (37-46 gpm)
Depending on rpm of prime mover
Tank volume 80 l (21 usg)
Electric motor - 55 kW, 50 Hz, 1 470 rpm, 380 V (75 hp)
- 63 kW, 60 Hz, 1 760 rpm, 440 V (85 hp)
Diesel engine Turbo charged four cylinder water cooled
diesel engine,
92 kW at 1 800 rpm (125 hp)

Special versions

Working platform
In the surface version the machine can be mounted on
working platform with rod rack, hydraulic jack legs, four
wheel bogie and tow bar.

Module design
The machine can also be delivered specially adapted for
helicopter transport in easily detachable modules with a
maximum weight of approx 400 kg (900 lb).
These modules are also available for mounting on user’s
own work platform, vehicle or trailer.

Special power packs

On request the power pack can be adapted for use at very
high altitudes.
Options

Alternative feed booms Wireline Mast

Detachable mast with rod support roller, prepared for
Feed booms attachment of wireline sheave wheel assembly.
Feed boom 900 mm (36’’) 2 200 mm (7’3’’)
Mast length
Total length 2 265 mm (7’5’’) 3 565 mm (11’8’’)
Underground version 1 000 mm (40’’)
- Alternatively 500 mm (20’’)
Surface version 2 000 mm (6’6’’)
All steel version
Heavy duty version Available in 1 m modules
The DE130 is also available in an all-steel version for use in (39 3/8’’)
conditions where aluminium may not be allowed.
Rotation unit
Drive spindle inner diameter 103 mm (4 1/16”).
High torque version
H-head
For applications where higher torque is required two
Torque - 312 Nm at 1100 rpm (230 lbf ft)
alternative rotation units are available. - 937 Nm at 460 rpm (691 lbf ft)
(Only for unit with 77 mm ID).
Speed infinitely variable 0-1 250 rpm
Number of jaws 12
High torque Medium torque
Gripping range 38-102 mm (1 31/64’’-4 1/64’’)

rpm 10-100 10-280 Gripping range, set of 15 mm (19/32’’)

jaws
Speed torque Nm 1 900 1 080
lbf ft 1 400 800
A modified carrier and a rodholder adaptor plate will be
required to fit this rotation unit on the feed boom.
Flush pump
Triplex flush pumps for mud or clear water. Capacities up
to 150 l/min (40 gpm). Maximum pressure up to 100 bar Alternative rod holders
(1450 psi).

Underground
Drive options: hydraulic, electric or diesel. Hydraulic drive
Type Cup springs for gripping,
will allow operation from the control panel. hydraulics for opening
Gripping range 37-80 mm (1 1/2’’-3 1/8’’ )
Gripping range for set of 18 mm (3/4’’)
Wireline hoist jaws
Two alternative wireline hoists, hydraulic drive, operated Number of jaws 2
from control panel. Max opening without jaws 89 mm (3 1/2’’)

“Big Jaw”
Type Hydraulics for gripping and
Drum capacity with 5 mm - 800 m (2 600’)
opening
(3/16’’) wire rope - 1 200 m (3 900’)
Gripping range - 36-150 mm (13/8’’-57/8’’)
Drum capacity with 6 mm - 600 m (1 960’)
- 53-300 mm (21/16’’-11 3/4’’)
(1/4’’) wire rope - 800 m (2 600’)
Number of jaws 2
Pulling force, bare drum 12,4 kN (2 700 lbf)
Speed, full drum 2,7 m/s (9’/s)

The 1 200 m wireline hoist is also available featuring cable

levelling winder to avoid premature wire rope failure and
to simplify operation.
Dimensions

Underground Surface
Drill unit mm inch mm inch mm inch
Feed length 1 700 67 900 36 2 200 87
A 4 065 160 3 265 129 5 565 219
B 2 980 118 2 180 86 3 480 137
C 3 065 121 2 265 90 3 565 140
D 1 050 42 1 050 42 1 050 41
E 1 020 41 1 020 41 1 050 41
F 650 26 650 26 650 26

Power unit
55 kW 92 kW
mm inch mm inch
I 1 600 63
K 1 430 56 2 100 83
L 860 34
M 1 040 41 1 900 75
N 840 33 1 000 39

Underground Underground/Surface
Mounting frame Control panel
mm inch mm inch
G 1 255 49 O 1 165 46
H 510 20 P 480 19
R 525 21
Weights

Underground Aluminium boom Surface

kg lb kg lb
Drill unit including feed boom, drill head 77 mm (N), rod holder and wall bracket 510 1 125 560 1 235
D:o with 103 mm (H) head 630 1 390 680 1 500
Mounting frame including tilt cylinder and support legs 200 440 225 496
Power pack 55 kW 640 1 411
Power pack diesel 92 kW 920 2 028
Hydraulic hoses 80 176 80 176
Control panel 110 242 110 242
Wireline hoist 800 m excl wire rope 87 192 87 192
Wireline hoist 1200 m excl wire rope 107 236 107 236
Wireline mast 1000 mm 40 88
Wireline mast 2000 mm 50 110

Working range

mm inch mm inch mm inch

Feed length 900 36 1 700 67 2 200 87
A 3 300 130 4 100 161 4 600 181
B 2 300 91 3 100 122 3 600 142
C 630 25 630 25 630 25
D 1 750 69 2 550 100 3 050 120

This equipment is constantly liable to review and

improvement and no responsibility can be accepted for
subsequent modifications making all or part of these
specifications obsolet.
 Sandvik is a high-technology engineering group with
world-leading positions in selected areas - tools for metal
working, advanced materials technology, and mining
and construction. We employ more than 50000 people
and are represented in 130 countries.

Sandvik Mining and Construction represents one third

of the overall Sandvik Group and serves a broad range
of customers in construction, mineral exploration,
mining and bulk materials handling. Our construction
expertise covers quarrying, tunnelling, demolition and
recycling, and other civil engineering applications. Our
mining products and services support customers on the
surface and under ground, including, coal, copper ore
and gold ore mining.

® SANDVIK is a registered trademark owned by Sandvik Companies in Sweden and other countries. © 2009 SANDVIK
Sandvik DE130 compact core drill 001ENG

SANDVIK MINING AND CONSTRUCTION • www.sandvik.com