CS6 & CS8 SERIES

PARTS LIST AND SERVICE MANUAL

U.S. Pat. 5,542,306

Muncie Power Products, Inc. General Offices and Distribution Center • P.O. Box 548 • Muncie, IN 47308-0548
(765) 284-7721 • FAX (765) 284-6991 • E-mail info@munciepower.com • Web site http://www.munciepower.com
Drive Products, Inc., Toronto, Exclusive Agents for Canada
 CS6 & CS8 SERIES PTO
EXPLODED VIEW

2 MUNCIE POWER PRODUCTS, INC. Rev. 11-00

 PARTS LIST AND DESCRIPTION
ITEM QTY PART NO. DESCRIPTION ITEM QTY PART NO. DESCRIPTION
1 1 See Chart Page 4 37 1 14T39137 Hyd Flange (“G” Only)
2 2 10T34006 Input Bearing (03 & 04) 14T36836 Hyd Flange (“I” Only)
2a 2 10T35776 Input Bearing (05 - 14) 14T39141 Hyd Flange (“Q” “T” Only)
3 1 18T34622 Spacer (03 & 04) 14T35464 Hyd Flange (“S” Only)
4 4 21T34621 Thrust Race (03 & 04) 14T37779 Hyd Flange (“V” Only
4a 1 18T35781 Shim (05 - 14) 14T37378 “2” Companion Flange
18T36229 Shim (05 - 14) 14T37357 “C” Companion Flange
18T36230 Shim (05 - 14) 37a 1 49T36833 Coupler (“I” Only)
5 2 10T34620 Thrust Bearing (03 & 04) 37b 1 18T36864 Spacer (“I” Only)
6 4 19T35237 Capscrew 37c 1 19T38266 Capscrew (“2” “C” “X”)
7 1 15T36717 Bearing Cover, Closed 37d 1 21T20092 Flat Washer (“2” “C” “X”)
15T36860 Closed Cover (CS6G) 38 4 19T33233 Capscrew (“B”)
8 1 11T36124 Seal 39 4 19T34462 Socket Capscrew “K” “P” “V” Hyd
8a 1 24T36894 Snap Ring 19T39257 Socket Capscrew “G” “Q” “S” “T” Hyd
9 1 12T34003 O-Ring 19M84478 Socket Capscrew “I”
10 2 10T21017 Bearing 40 1 28T36546 Spacer
11 4 26T36175 Roll Pin 41 1 16T33999 Cover
12 1 21T36473 Plate 42 4 19T34028 Capscrew
13 1 21T36511 Thrust Washer 43 1 13T34022 Gasket
14 1 21T36512 Plate 44 4 25T21684 Pipe Plug
15 1 24T27240 Snap Ring 45 4 19T36174 Setscrew
16 2 24T35480 Snap Ring 46 4 27T36173 Spring
17 2 21T29017 Thrust Race 47 1 25T35724 Cap Plug “K” “S” “Q” “G” (Storage Only)
18 1 10T36285 Bearing 25T35725 Cap Plug “P” (Storage Only)
19 1 02T36744 Bell Gear 03 (42T) 48 1 13M13541 Allison Gasket .031 (U60)
02T36745 Bell Gear 04 (39T) 1 13M35091 Gasket .010 6-Bolt
02T36746 Bell Gear 05 (38T) 1 13M35092 Gasket .020 6-Bolt
02T37913 Bell Gear 06 (36T) 2 13M35151 Gasket .010 8-Bolt
02T36747 Bell Gear 07 (33T) 2 13M35152 Gasket .020 8-Bolt
02T36748 Bell Gear 09 (30T) 1 13T35198 Gasket .010 (I85)
02T36749 Bell Gear 12 (26T) 1 13T35199 Gasket .020 (I85)
02T36750 Bell Gear 14 (23T) 49 1 43T37385 Orifice Fitting (P - Special Option)
20 1 02T35454 Clutch Hub 50 2 26T37992 Dowel Pin (F84 Only)
21 8 49T33564 Friction Disc N.S. 1 CS6-GSK Gasket Kit
22 7 49T33563 Spacer Disc Includes: (1)8, (1)9, (1)25, (2)26,
23 1 27T36112 Spring (2)29, (1)35, (1)36, (1)43,
24 1 49T36560 Piston (1)13M35091, (1)13M35092
25 1 12T36054 O-Ring
26 2 12T36471 O-Ring N.S. 1 CS8-GSK Gasket Kit
27 1 49T36561 Piston Cup Includes: (1)8, (1)9, (1)25, (2)26,
28 1 24T36470 Snap Ring (2)29, (1)35, (1)36, (1)43,
29 2 12T35949 O-Ring (03 & 04) (1)13M35151, (1)13M35152
12T35774 O-Ring (05 - 14) N.S. 1 CS6-RBK-03 Rebuild Kit (03 & 04)
30 1 19T35785 Setscrew CS6-RBK-05 Rebuild Kit (05 - 14)
31 1 07T35947 Idler Shaft (03 & 04) Includes: (2)2*, (4)4*, (2)5*, (1)8, (1)9,
07T37071 Idler Shaft (05 - 14) (2)10, (1)13, (1)15, (2)16, (2)17, (1)18,
32 1 01T36713 6 Bolt Housing (03 & 04) (1 Arrng) (8)21, (7)22, (1)23, (1)25, (2)26, (1)28,
01T36706 6 Bolt Housing (03 & 04) (3 Arrng) (2)29, (1)35, (1)36, (1)43, (2)46,
01T37107 6 Bolt “N” Housing (05-14) (1 Arrng) (1)13M35091, (1)13M35092
01T37106 6 Bolt “N” Housing (05-14) (3 Arrng) *Use part number as required by ratio No.
01T37966 6 Bolt “F” Housing “1” (F84 Only)
01T37965 6 Bolt “F” Housing “3” (F84 Only) N.S. 1 CS8-RBK-03 Rebuild Kit (03 & 04)
01T36715 8 Bolt Housing (03 - 04) (1 Arrng) CS8-RBK-05 Rebuild Kit (05 - 14)
01T36711 8 Bolt Housing (03 - 04) (3 Arrng) Includes: (2)2*, (4)4*, (2)5*, (1)8, (1)9,
01T37073 6 Bolt Housing (05 & 14) (1 Arrng) (2)10, (1)13, (1)15, (2)16, (2)17, (1)18,
01T37072 6 Bolt Housing (05 & 14) (3 Arrng) (8)21, (7)22, (1)23, (1)25, (2)26, (1)28,
01T37075 8 Bolt Housing (05 - 14) (1 Arrng) (2)29, (1)35, (1)36, (1)43, (2)46,
01T37074 8 Bolt Housing (05 - 14) (3 Arrng) (1)13M35151, (1)13M35152
33 1 06T36892 Output Shaft “B” & “I” 1-1/4 Rd *Use part number as required by ratio No.
06T37088 Output Shaft “G” Dana Special
06T36893 Output Shaft “K” & “V” 7/8 - 13 Spl
06T37090 Output Shaft “Q” & “S” 7/8-13 Spl
06T37089 Output Shaft “P” 1"-15 Spl PTO ASSEMBLY ARRANGEMENTS
06T37336 Output Shaft “T” 3/4"-11 Spl 1 3
06T37372 “2” “C” “X” Rd. 21-Spline
06T37167 Output Shaft “B” CS6G
06T37168 Output Shaft “K” “V” CS6G
34 1 26T01627 Woodruff Key
35 1 12T36751 O Ring
36 1 11T37790 Seal
37 1 15T34576 Bearing Cover, Open (“B”)
14T35537 Hyd Flange (“K” “P” Only)

Rev. 11-00 MUNCIE POWER PRODUCTS, INC. 3

 GEAR DATA
TABLE 1 INPUT GEAR ITEM 3 OUTPUT GEAR ITEM 17
DESIGNATOR PART NO. TEETH GEAR DATA PART NO. TEETH
A6803 03T37028 26/14 6.86P 20° PA SPUR 02T36744 42T
A6804 03T37910 26/17 6.86P 20° PA SPUR 02T36745 39T
A6805 03T37911 26/18 6.86P 20° PA SPUR 02T36746 38T
A6807* 03T37980 30/23 6.86P 20° PA SPUR 02T36747 33T
C6112 03T37067 20/30 6.1P 25° PA 32° 16'48" LH 02T36749 26T
C7009 03T37652 23/26 7P 25° PA 30° 46'48" LH 02T36748 30T
C7012 03T37068 23/30 7P 25° PA 30° 46'48" LH 02T36749 26T
F1012 03T37984 42/30 10.1P 20° PA SPUR 02T36749 26T
F1107 03T37156 42/23 10.1P 21.5° PA 29° SPUR 02T36747 33T
F6107 03T37147 21/23 6.1P 20.5° PA 29° SPUR 02T36747 33T
F6307 03T37086 24/23 6.35P 20° PA 22" LH 02T36747 33T
F6309 03T38356 24/26 6.35P 20° PA 22" LH 02T36748 30T
F6312 03T37087 24/30 6.35P 20° PA 22" LH 02T36749 26T
F7005 03T38195 26/18 7P 23° 26" LH 02T36746 38T
F7007 03T38194 26/23 7P 23° PA 26" LH 02T36747 33T
F8405 03T37741 28/18 8.38P 18° 33.1° LH 02T36746 38T
F8407 03T37742 28/23 8.38P 18° 33.1° LH 02T36747 33T
F8409 03T37743 28/26 8.38P 18° 33.1° LH 02T36748 30T
F8507 03T37066 34/23 8.55P 21° PA SPUR 02T36747 33T
I8403 03T37329 34/14 8.46P 20° PA SPUR 02T36744 42T
I8404 03T37330 34/17 8.46P 20° PA SPUR 02T36745 39T
I8405 03T37331 34/18 8.46P 20° PA SPUR 02T36746 38T
I8407 03T37332 34/23 8.46P 20° PA SPUR 02T36747 33T
I8505 03T37091 38/18 8.46P 20° SPUR 02T36746 38T
I8507 03T37092 38/23 8.46P 20° SPUR 02T36747 33T
M6504 03T36775 26/17 6.48P 17.65° PA SPUR 02T36745 39T
M6505 03T37070 26/18 6.48P 17.65° PA SPUR 02T36746 38T
M6507 03T37058 26/23 6.48P 17.65° PA SPUR 02T36747 33T
M6509 03T37059 26/26 6.48P 17.65° PA SPUR 02T36748 30T
M6512 03T37060 26/30 6P 17.5° PA SPUR 02T36749 26T
S6007 03T37061 21/23 6.48P 17.65° PA 26° 10'37" LH 02T36747 33T
S6807 03T37062 26/23 6/8P 20° SPUR 02T36747 33T
S6809 03T37063 26/26 6/8P 20° SPUR 02T36748 30T
S6812 03T37064 26/30 6/8P 20° SPUR 02T36749 26T
S6814 (8-Bolt) 03T37110 26/33 6/8P 20° SPUR 02T36750 23T
S7009 03T37065 24/26 7P 17.5° PA 28° 4'23" LH 02T36748 30T
S7107 03T37149 29/23 7P 17.5° PA 18° LH 02T36747 33T
S7109 03T37134 29/26 7P 17.5° PA 18° LH 02T36748 30T
S7307 03T37919 28/23 7P 22.5° PA 19° LH 02T36747 33T
S7309 03T38171 28/26 7P 22.5° PA 19° LH 02T36748 30T
S7312 03T38170 28/30 7P 22.5° PA19° LH 02T36749 26T
U6003 03T36737 24/14 6P 20° PA SPUR 02T36744 42T
U6004 03T36738 24/17 6P 20° PA SPUR 02T36745 39T
U6005 03T37069 24/18 6/8P 20° PA SPUR 02T36746 38T
U6806 03T38262 24/20 6/8P 20° SPUR 02T37913 36T
U6807 03T37038 24/23 6/8P 20° SPUR 02T36747 33T
U6809 03T37039 24/26 6/8P 20° SPUR 02T36748 30T
U6812 03T37040 24/30 6/8P 20° SPUR 02T36749 26T
U6814 (8-Bolt) 03T37042 24/33 6/8P 20° SPUR 02T36750 23T

* Requires 23M60270 and 20MKM603 to mount, included in PTO.

4 MUNCIE POWER PRODUCTS, INC. Rev. 11-00

 CS6 & CS8 INSTALLATION KITS
CLUTCH SHIFT ELECTRIC/AIR SHIFT SYSTEM ITEM QTY PART NO. DESCRIPTION
KIT NO. 48TK3928 12V ELECTRIC AIR SHIFT 30T36270 Switch Assembly 12v (Incl 1,2,3,4)
(For Use When Air Shifting CLUTCH SHIFT) 1 1 36MA1005 Switch Bracket
2 1 36M01006 Face Plate W/Overspeed Light Access
36T36271 Face Plate W/O Light Access
3 1 32MSR12V Light Assembly 12v
4 1 30T35687 Rocker Switch 12v
5 1 33T36299 Fuse Assembly
6 1 35M30692 Solenoid Valve 12v
7 1 30T37954 Pressure Switch
8 1 31M15759 Pressure Protection Valve
9 1 44MB2164 Pipe Nipple
10 1 34T36941 Wiring Pigtail
11 2 44MB6844 Male Connector
12 2 44MB6842 Male Connector
13 1 25T21684 Pipe Plug (Use As Req.)
14 3 34M18250 Female Spade Connector
15 2 34M18009 Ring Terminal
16 12 37M18000 Electric Wire 12ft
17 1 31M14732 Pressure Safety Switch (80 PSI)
18 1 44MB2254 Street Tee
19 1 44MB0942 Reducer Bushing
Parts Included with PTO (Not with Kit No. 48TK3928) “P” Special Option:
20 1 45M44430 Air Tubing 30ft
21 1 45M4R536 Lube Hose Assembly
22 1 43T37385 Orifice Fitting
23 1 43MB2252 Street Tee
N.S. 1 43M05522 Addl. Elbow (F85 Only)
N.S. 2 43T37429 Fitting (I85 Only)
For 24V Electric/Air Kit No. 48TK3931, Substitute:
1 30T36453 Switch Assembly 24v (Incl 1,2,3,4)
3 1 32MSR24V Light Assembly 24v
4 1 30T35712 Rocker Switch 24v
6 1 35M31692 Solenoid Valve 24v

CLUTCH SHIFT ELECTRIC/HYDRAULIC SYSTEM ITEM QTY PART NO. DESCRIPTION

KIT NO. 48TK3927 12V ELECTRIC/HYDRAULIC SHIFT 30T36270 Switch Assembly 12v (Incl 1,2,3,4)
1 1 36MA1005 Switch Bracket
2 1 36M01006 Face Plate w/Overspeed Light Access
36T36271 Face Plate w/o Light Access
3 1 32MSR12V Light Assembly 12v
4 1 30T35687 Rocker Switch 12v
5 1 33T36299 Fuse Assembly
6 1 35M12340 Solenoid Valve 12v
7 1 30T37954 Pressure Switch
9 1 34T36941 Wiring Pigtail
10 2 43MX044S Screen Adapter
13 3 34M18250 Female Spade Connector
14 2 34M18009 Ring Terminal
15 12 37M18000 Electric Wire 12ft
16 1 43T35867 Elbow, Pipe to JIC incl. w/parts bag
Parts Included with PTO (Not with Kit No. 48TK3927) “P” Special Option:
17 1 45M4R536 Lube Hose Assembly
18 1 43T37385 Orifice Fitting
19 1 44MB2252 Street Tee
N.S. 1 43M05522 Addl. Elbow F85 Only)
N.S. 2 43T37429 Fitting (I85 Only)
For 24V Electric/Hydraulic Kit No. 48TK3930, Substitute:
30T36453 Switch Assembly 24v (Incl 1,2,3,4)
3 1 32MSR24V Light Assembly 24v
4 1 30T35712 Rocker Switch 24v
6 1 35M24340 Solenoid Valve 24v

Rev. 11-00 MUNCIE POWER PRODUCTS, INC. 5

 CS6 & CS8 INSTALLATION KITS
CLUTCH SHIFT MANUAL AIR SHIFT SYSTEM ITEM QTY PART NO. DESCRIPTION
KIT NO. 48TK3926 MANUAL AIR SHIFT – 12V LIGHT 1 1 32M12001 Light Assembly 12v
2 1 33T36299 Fuse Assembly
3 1 35M18653 Air Valve
4 1 30T37954 Pressure Switch
5 1 31M15759 Pressure Protection Valve
6 1 44MB2164 Pipe Nipple
7 1 34T36941 Wiring Pigtail
8 1 44MB6942 Fitting - Elbow
9 2 44MB6842 Male Connector
10 1 44MB6844 Male Connector
11 1 25T21684 Pipe Plug
12 2 34M18009 Ring Terminal
13 12 37M18000 Electric Wire 12ft
14 3 34T36362 Closed End Crimp
N.S. 1 36MA1004 Dash Bracket
N.S. 1 36M01005 Face Plate
N.S. 1 36MK1007 Bolt Kit
Parts Included with PTO (Not with Kit No. 48TK3926) “P” Special Option:
15 1 45M44430 Air Tubing 30ft
16 1 45M4R536 Lube Hose Assembly
17 1 43T37385 Orifice Fitting
18 1 44MB2252 Street Tee
N.S. 1 43M05522 Elbow
N.S. 2 43T37429 Fitting (I85 Only)
For 24V Electric/Hydraulic Kit No. 48TK3929, Substitute:
1 1 32M24001 Light Assembly 24v

MODEL NUMBER CONSTRUCTION

CS 6S — M65 07 — E 1 B X
PTO Type Special Feature
Clutch Shift — CS X — None
Mounting C — Pulse Generator/Pres Lube/EOS-111
D — Pulse Generator/EOS-111
SAE 6 Bolt Std. Mtg. — 6S
P — Pressure Lube
SAE 6 Bolt Non-Std. Mtg. — 6D
SAE 6 Bolt Non-Std. Mtg. (Isuzu) — 6N R — Pulse Generator/No Pressure Lube
SAE 6 Bolt Std. Mtg., Metric Stud Kit — 6B S — Pulse Generator/Pressure Lube
SAE 6 Bolt Deep Mtg., Metric Stud Kit — 6C Output Type
SAE 6 Bolt Std., Less Drag Brake (CS6 Only) — 6G B — 1-1/4 Round 5/16 KW
SAE/ISO 6 Bolt Std., w/Dowel Holes — 6F C — 1410 Companion Flange
SAE 8 Bolt Std., Less Drag Brake (CS8 Only) — 8G G — Special
SAE 8 Bolt Std. Mtg. — 8S I — DIN 5462
SAE 8 Bolt Deep Mtg. — 8D
K — SAE “B” 2 & 4 Bolt
SAE 8 Bolt Std. Mtg., Metric Stud Kit — 8B
SAE 8 Bolt Deep Mtg., Metric Stud Kit — 8C P — SAE “BB” 2 & 4 Bolt
Q — SAE “A” 2 Bolt
Trans. CS Gear Data S — SAE “B” 2 Bolt
Aisin 8.46P 20°PA Spur — I84 T — SAE “A” 3/4" 11 Spl. 2 Bolt
Allison 6.86P 20°PA Spur — A68 V — SAE “B” 2 & 4 Bolt
Clark 6.1P 25°PA 32.28° LH — C61 X — 1.3-21 Spline
Clark 7P 25°PA 30.78° LH — C70 2 — DIN Companion Flange
Fuller 1.01P 20°PA Spur — F10 Assembly Arrangement
Fuller 1.01P 21.5°PA Spur — F11 1 3
Fuller 6.1P 20.5°PA 29° LH — F61
Fuller 6.35P 20°PA 22° LH — F63 Shifter Type
Fuller 6.1P 23°PA 26° LH — F70 A — Manual Air
Fuller 8.38P 18°PA 33.1° LH — F84 E — Elect/Air (12V)
Fuller 8.55P 21°PA Spur — F85 F — Elect/Air (24V)
Isuzu 8.46P 20°PA Spur — I85 H — Elect/Hyd (12V)
Mack 6.48P 17.65°PA Spur — M65 J — Elect/Hyd (24V)
Spicer 6P 17.5°PA 28.7° LH — S60 Speed Ratio
Spicer 6 or 6/8P 20°PA Spur Deep Dish — S68 03 — .33:1 09 — .87:1
Spicer 7P or 17.5°PA 28.07° LH — S70 04 — .44:1 12 — 1.15:1
Spicer 7P 17.5°PA 18° LH — S71
05 — .47:1 14 — 1.44:1 (8 Bolt Only)
Spicer 7P 22.5°PA 19° LH — S73
06 — .55:1
Universal 6P 20°PA Spur — U60 07 — .70:1
Universal 6 or 6/8P 20°PA Spur — U68

6 MUNCIE POWER PRODUCTS, INC. Rev. 11-00

 IN INCHES (MM) CS6 & CS8 DIMENSIONS IN INCHES (MM)

CS6N HOUSING DIMENSION

CS6G HOUSING OPTION
“B” OR “K” SHAFT ONLY.
CS6/8S HOUSING DIMENSION NO DRAG BRAKE.

STANDARD 1-1/4" ROUND KEYED SHAFT (“B” OPTION)

Optional Pump
Bolt Kit
19MK4717
Sold Separately.

SPECIAL 7/8" - 13 SPLINE (“G” OPTION) S.A.E. “A” 2-BOLT 7/8" - 13 SPLINE (“Q” OPTION)

1410 SERIES COMPANION FLANGE (“C” OPTION) S.A.E. “B” 2 & 4 BOLT 7/8" - 13 SPLINE (“K” OPTION)

S.A.E. “B” 2-BOLT 7/8" - 13 SPLINE (“S” OPTION) DIN 100 COMPANION FLANGE (“2” OPTION)

S.A.E. “B-B” 2 & 4 BOLT 1"-15 SPLINE (“P” OPTION) S.A.E. “B” 2 & 4 BOLT 7/8" - 13 SPLINE (“V” OPTION)

S.A.E. “A” 2-BOLT 3/4" - 11 SPLINE (“T” OPTION)

Rev. 11-00 MUNCIE POWER PRODUCTS, INC. 7

 CS6 & CS8 DISASSEMBLY AND REASSEMBLY
(REFERENCE EXPLODED VIEW ON PAGE 2)
DISASSEMBLY PROCEDURE – DENOTES SPECIAL SERVICE PROCEDURES
1. Remove the CS6S input gear, by removing the set
screw in the pad and driving the idler shaft from the
housing (Items 30, 32).
2. Remove the set screws (Item 45) from the bearing cover
(Item 7) which hold the drag brake springs (Item 46).
Position the housing so that the springs fall from housing.
3. Remove the four (4) capscrews (Item 6) which hold the back
cover to the PTO housing.
4. Position the housing against a bench block and hit the end
of the output shaft with a soft face hammer to remove
the entire output shaft assembly with bearing cover.
5. Remove the two (2) pipe plugs (Item 44) from the
bearing cover. This exposes the ball bearing assembly
within the cover.
6 Using a 1/4" punch and alternating between the two
holes, drive the bearing and shaft assembly from the bearing cover.
7 Using a bearing puller remove the rear bearing (Item 10) by grabbing the drag brake plate (Item 12) and removing both
pieces. The bronze brake disk (Item 13) can be removed.
8. Using a bearing puller remove the drag brake rotor (Item 14).
9. The piston and clutch pack may be serviced without removal of the drag brake. Using snap ring pliers, remove the snap
ring (Item 28) located on the output shaft end while gently pushing on the piston cup (Item 27).
10. Pull the piston cup (Item 27) from the shaft and the piston (Item 24) will go with it.
11. Tap the piston cup on a wood surface to remove the piston.
12. Remove the spring (Item 23). The clutch friction discs (Item 21) and spacer discs (Item 20) and inner clutch hub (Item 20)
can be removed by pointing the shaft end down.
13. With the drag brake removed, the snap rings (Item 15 & 16) on this end of the bell gear can be removed with snap ring
pliers. This allows the bell gear to be removed towards the closed end. The internal bearing (Item 18) of the bell gear can
easily be removed.
REASSEMBLY PROCEDURE
14. The reassembly of the unit is made in reverse of the disassembly.
15. Be sure to lubricate the o-rings and all bearings upon installation. TAPER ROLLER BEARINGS
Torque capscrews to the values shown or to the (RATIOS 05 THRU 14)
following values.
5/16 capscrews - 18 ft.lb.
3/8 capscrews - 36 ft.lb.
1/4 set screw - 9 ft.lb.
16. Place the input bearing into the input gear and
slide this group into the housing to line up the
idler shaft.
17. Tap the idler shaft into the housing and through
both bearing races.
18. Tap the idler shaft in the reverse direction so
that it is flush with the bearing in this assembly.
Insert the thickest shim that can be installed by
hand in the gap between the bearing and the
housing. Rotate the input gear to ensure it is not
excessively tight or loose. Recommended
bearing pre-load is .002" loose to .006" loose.
19. Tap the idler shaft into position and install the
set screw.

DRAG BRAKE ADJUSTMENT

20. When installing the rear cover be sure to align the roll pins
in the drag brake plate with the holes in the rear cover.
21. After the cover has been attached to the housing insert the
springs into the holes.
22. Insert the set screw over the spring and turn the screw four
(4) full turns.
23. Follow the test and adjustment procedures in the PTO Owner’s manual.

Rev. 11-00 MUNCIE POWER PRODUCTS, INC. 8

 MOUNTING KITS

6-MOUNTING KIT LUBE HOSE KITS

43TK3934 HOSE KIT (STANDARD)

ITEM QTY PART NO. DESCR. ITEM QTY PART NUMBER DESCRIPTION
1 1 45M4R536 Hose Assembly Std.
20MK6601 CS6S, CS6D, CS6N-S71,S73 2 1 43M05522 Elbow
1 6 20M38150 Stud
2 6 13M18018 Copper Washer
3 6 21MX3802 Lock Tab
4 6 22MX3824 Nut SPEED SENSOR KIT 8-MOUNTING KIT
20MKM602 CS6B, CS6C 16TK3833 SPECIAL OPTION
1 6 20M39040 Stud
“C”, “D”, “R”, & “S”
2 6 13M18018 Copper Washer
3 6 21MX3802 Lock Tab
4 6 22MX3824 Nut
20MKM603 CS6B-A6807
1 6 20M39045 Stud
2 6 13M18018 Copper Washer
3 6 21MX3802 Lock Tab
4 6 22MX3824 Nut
20TK4075 CS6B-I84
1 6 20T38143 Stud
2 6 13M18018 Copper Washer ITEM QTY PART NO. DESCR. ITEM QTY PART NO. DESCR.
3 6 21MX3802 Lock Tab 1 1 31T35108 Mag Pickup 20MK8800 CS8S, CS8D
4 6 22MX3824 Nut 2 1 21T35109 Jam Nut 1 6 19M44138 Capscrew
20MKM104 CS6N-I85 3 1 34MA1415 Wiring Harness 2 2 20M44175 Stud
1 4 20M39040 Stud 4 1 21T36099 Flat Washer 3 8 21ML4375 Lock Washer
2 20M39045 Stud 5 1 12T35774 O-Ring 4 2 22MX4420 Nut
2 6 13M18018 Copper Washer N.S. 1 16T35523 Cover, Mag 20MKM802 CS8B, CS8C
3 6 21MX3802 Lock Tab Pickup
N.S. 1 25T35565 Plug 2 8 20M47055 Stud
4 6 22MX3824 Nut
3 8 21ML4375 Lock Washer
20TK4046 CS6F-F84 4 8 22MX4420 Nut
1 6 20M39040 Stud
2 6 13M18018 Copper Washer
3 6 21MX3802 Lock Tab
4 6 22MX3824 Nut
N.S 1 13M51717 Loctite GSK Elim
N.S. 1 MC99-06 Inst. Card

Rev. 11-00 MUNCIE POWER PRODUCTS, INC. 9

 The CS6 & CS8 PTOs include mounting kit,
special shim/gasket, wiring harness, dash
bracket kit, and installation instructions. The
installation does not require any special tools.
The PTO is available with a pulse generator
pick-up for use with which the Muncie digital
tachometer 38MK2000 (request MP92-04)
or use with the Muncie overspeed switch
EOS-111 to control the engagement or
overspeed protection of the PTO.
Contact your Muncie Application Specialist
for assistance with these options.

uncie Muncie Power Products, Inc. General Offices and Distribution Center • P.O. Box 548 • Muncie, IN 47308-0548
Po er (765) 284-7721 • FAX (765) 284-6991 • E-mail info@munciepower.com • Web site http://www.munciepower.com
Products Drive Products, Inc., Toronto, Exclusive Agents for Canada
SP96-05 (Rev. 11-00) Printed in the U.S.A.
© Muncie Power Products, Inc. 2000