Btech Mech

B.Tech Course Structure and Syllabus for the year 2011, 2012.
2013 and 2014
FACULTY OF ENGINEERING
Kengeri Campus, Kanminike, Kumbalagodu, Bangalore – 560060
COURSE STRUCTURE AND SYLLABUS
B.Tech (Mechanical)
Modified for the years
2011-12, 2012-13, 2013-14
and approved for the year
2014-15
Department of Mechanical Engineering- Christ University Faculty of Engineering Page 1

B.Tech Course Structure and Syllabus for the year 2011, 2012.2013 and 2014
CONTENTS
Sl CONTENTS
PAGE NUMBER
1 Introduction 3-4
2 Courses Offered 5
3 Eligibility Criteria 6
4 Selection Process 7
5 Admission Process 7-8

6 General Rules 7
7 Grading Scheme for Each Paper: Undergraduate Courses 8

8 Grading Scheme for Each Paper: post Graduate Courses 9-10
9 Course Overview 10
10 Course Objective 11
11 Teaching Pedagogy 10-11
12 Assessment Rules 12
13 Question Paper Pattern 12

14 Course Structure 13-19
15 Detailed Syllabus 17-230

ABOUT US
01.INTRODUCTION
Christ University was formerly Christ College (Autonomous) affiliated to Bangalore

University. Established in July 1969, Christ College became the most preferred educational
institution in the city of Bangalore within the first three decades. From 1990 onwards it scaled
from heights to heights. By the introduction of innovative and modern curriculum, insistence on
academic discipline, imparting of Holistic Education and with the help of the creative and
dedicated staff, Christ College has been continually rated among the top 10 educational
institutions of the country. It has the rare distinction to be the first institution in Karnataka to be
accredited by National Assessment and Accreditation Council (NAAC) UGC for
qualityeducation. On 7 October 2004, UGC has conferred Autonomy to Christ College
(No.F.13-/2004).
On May 20, 2005, it became the first College in South India to be reaccredited with A+ by
NAAC. UGC has identified it as an Institution with Potential for Excellence in June 2006. July
22, 2008 is the most glorious day in the history of the institution. Under Section 3 of the UGC
Act, 1956, Ministry of Human Resources Development of the Union Government of India, vide
Notification No. F. 9-34/2007-U.3 (A), has declared it a Deemed to be University, in the name
and style of Christ University

Christ University
VISION
"EXCELLENCE AND SERVICE"
 Christ University, a premier educational institution, is an academic fraternity of individuals dedicated
to the motto of excellence and service. We strive to reach out to the star of perfection through an
earnest academic pursuit for excellence and our efforts blossom into „service‟ through our creative
and empathetic involvement in the society to transform it.
 Education prepares one to face the challenges of life by bringing out the best in him/her. If this is
well accepted, education should be relevant to the needs of the time and address the problems of the
day. Being inspired by Blessed Kuriakose Elias Chavara, the founder of Carmelites of Mary
Immaculate and the pioneer in innovative education, Christ University was proactive to define and
redefine its mission and strategies reading the signs of the time.
MISSION
"Christ University is a nurturing ground for an individuals holistic development to make

effective contribution to the society in a dynamic environment."
Department of Mechanical Engineering

VISION
TO IMPART EXCELLENT TECHNICAL EDUCATION IN MECHANICAL ENGINEERING PROGRAMS
THAT WILL ENABLE THE STUDENTS TO SERVE THE SOCIETY
MISSION
“To develop Mechanical Engineering students into responsible and passionate
professionals, who are able to actively pursue and solve real life problems in a dynamic
environment through prudent, lean and creative usage of resources”
CORE VALUES
The values which guide us at Christ University are:

o Faith in God
o Moral Uprightness
o Love of Fellow Beings
o Social Responsibility
o Pursuit of Excellence

02. COURSE OFFERED

 Undergraduate Programmes (B. Tech in)
B. Tech in-
- Civil Engineering( CIVIL)
- Computer Science and Engineering (CSE)
- Electronics and Communication Engineering (ECE)
- Electrical and Electronics Engineering (EEE)
- Information Technology (IT)
- Mechanical Engineering (MECH)
- Automobile Engineering (AE)
 Int. BTech with MBA
- Int. BTech(CIVIL) with MBA (Finance/HR/Marketing/Lean Operations & Systems)
- Int. BTech(CSE) with MBA (Finance/HR/Marketing/Lean Operations & Systems)
- Int. BTech(ECE) with MBA (Finance/HR/Marketing/Lean Operations & Systems)
- Int. BTech(EEE) with MBA (Finance/HR/Marketing/Lean Operations & Systems)
- Int. BTech(IT) with MBA (Finance/HR/Marketing/Lean Operations & Systems)
- Int. BTech(MECH) with MBA (Finance/HR/Marketing/Lean Operations & Systems)
 Int. BTech with M. Tech (5 Years Program)
- Int. BTech(Civil) with MTech (Structural Engineering)
- Int. BTech(CSE) with MTech (CSE)
- Int. BTech(ECE) with MTech (Communication Systems)
- Int. BTech(EEE) with MTech (Power Systems)
- Int. BTech(IT) with MTech (IT)
- Int. BTech(Mech) with MTech (Machine Design)
 Postgraduate Programmes (M. Tech) (2 Years Program)
- Master of Technology in Computer Science & Engg.
- Master of Technology in Communication Systems
 Doctoral Programmes (Ph.D.) (Doctor of Philosophy)
- Doctor of Philosophy (Ph.D.) in Computer Science and Engineering
- Doctor of Philosophy (Ph.D.) in Electronics and Communication Engg.
- Doctor of Philosophy (Ph.D.) in Mechanical Engineering

03. ELIGIBLITY CRITERIA

 For Undergraduate Programmes and Int. B Tech with MBA & Int. B. Tech with
M. Tech:
A pass in PUC (10+2) or equivalent with 50% marks in aggregate with Mathematics, Physics
and Chemistry is the minimum eligibility for admission
Lateral Entry:
Candidates who have successfully completed 3 year diploma in Engineering are eligible to
apply for lateral entry into BTech courses
Candidates will be admitted to second year of the programme only after appearing the Christ
University selection process for engineering programmes.
 For Postgraduate Programmes:
o For Master of Technology in Computer Science & Engineering

 A Pass in B.Tech/B.E or M.Sc with 55% aggregate.
o For Master of Technology in Communication Systems
 A Pass in B.Tech/B.E or M.Sc in Electronics and VLSI Design
with 55% aggregate.
o For Master of Technology in Civil Engineering
 A Pass in BE/BTech or M.Sc in Civil and VLSI Design with 55%
aggregate.
o For Master of Technology in Mechanical Engineering
o A Pass in BE/BTech.
 For Doctoral Programmes (Ph.D.):

 A pass with 55% marks in post graduation and equivalent in the
relevant subject from any recognized university.
 A research proposal (Maximum 1500 words) has to be submitted
along with the application.

04. SELECTION PROCESS
1) Candidates can process the admission based on the Undergraduate Entrance Test
and Ranking by COMEDK. OR
2) Christ University Selection Process as given below:
Process Particulars Date Venue/Centre

Entrance Test Christ University As per the E- As per the E- Admit
Entrance test for each Admit Card Card
candidate
Personal Personal interview for 15 As per the E- As per the E- Admit
Interview minutes for each candidate Admit Card Card
by an expert panel
Academic Assessment of past As per the E- As per the E- Admit
Performance performance in Class Admit Card Card
10, Class 11/12 during the
Personal Interview
05. ADMISSION PROCESS
Candidates will be intimated about the Selection status (Selected/Wait Listed/Not

Selected) through the University Notice Board/on the “Application Status” link on University
website. The Selection results will be declared within 24 Hoursof Personal Interview sessions.
The selected candidates must process admission at Office of Admissions, Central
Block, Christ University within 3 working days of declaration of Selection Process
results/as per the stipulated date and time mentioned by Office of Admissions.
Selected candidates should collect the Fee Challan from the Office of Admissions and
remit the Annual fee at the South Indian Bank, Christ University Branch. The Offer of
Admission will stand cancelled, if failing to remit the fee within the stipulated date and time.
Admission will not be processed without the presence of the candidate and the
mandatory original documents mentioned below;
1. The Offer of Admission Card (E-Admission Card/Mail)
2. Class 10 Marks Statement
3. Class 11 Marks Statement, if Candidate is pursuing class 12 and appearing for
final examination during March-April
4. Class 12 Marks Statement, if candidate has appeared and passed the Class 12

examination
The University ID card is a smart card, which is both an ID card as well as a South
Indian Bank ATM card with a chip containing the student personal details. All transactions
within the University campus after commencement of classes, including fees payment will be
processed only through this card. It is also an access card for Library and other restricted places.
Candidates are advised to collect the South Indian Bank account opening form along with fees
challan and process it at the Bank branch within the University premises.
Candidates who fall under International student category (ISC), If selected, should
register with the Foreigner Regional Registration Officer (FRRO/FRO) of the Local Police in
Bangalore, India within 14 working days from the date of admission or arriving in Bangalore.
All International student category (ISC) candidates if studied in India should obtain an NOC
from the previous qualifying institution.
06. GENERAL RULES
 There is a grading scheme for each paper and for all the courses.
 All marks will indicate the marks, percentage obtained, grade and grade point
average.
 The grade point average will be calculated as follows: for each subject, multiply
the grade point with the number of credits; divide the sum of product by the total
number of credits.
 The CGPA [Cumulative GPA] is calculated by adding the total number of earned
points [GP x Cr] for all semesters and dividing by the total number of credit
hours for all semesters.
∑
GPA=
∑


07. Grading scheme for Each Paper: Undergraduate Courses

Percentage Grade Grade Point Interpretation Class
80 and above A 4.0 Outstanding First Class with
Distinction
73-79 A- 3.67 Excellent
66-72 B+ 3.33 Very Good First Class
60-65 B 3.0 Good
55-59 B- 2.67 Average
Second Class
50-54 C+ 2.33 Satisfactory
45-49 C 2.00 Pass
Pass Class
40-44 D 1.0 Pass
39 and below F 0 Fails Fail
08. Grading scheme for Each Paper: Postgraduate Courses
Percentage Grade Grade Point Interpretation Class

80 and above A+ 4.0 Excellent First Class with
70-79 A 3.5 Very Good Distinction
65-69 B+ 3.0 Good
First Class
60-64 B 2.5 Above Average
55-59 C+ 2.0 Average
Second Class
50-54 C 1.5 Satisfactory
40-49 C- 1.0 Exempted if aggregate
Pass Class
is more than 50%
39 and below F 0 Fails Fail

DETAILS OF CIA (Continuous Internal Assessment):

Assessment is based on the performance of the student throughout the semester.
Assessment of each paper
 Continuous Internal Assessment (CIA) for Theory papers: 50% (50 marks out
of 100 marks)
 End Semester Examination(ESE) : 50% (50 marks out of 100 marks)
Components of the CIA
CIA I : Mid Semester Examination (Theory) : 25 marks
CIA II : Assignments : 10 marks

CIA III: Quizzes/Seminar/Case Studies/Project Work : 10 marks
Attendance : 05 marks
Total : 50 marks
For subjects having practical as part of the subject

End semester practical examination : 25 marks
Records : 05 marks
Mid semester examination : 10 marks
Class work : 10 marks
Total : 50 marks
Mid semester practical examination will be conducted during regular practical hour with
prior intimation to all candidates. End semester practical examination will have two
examiners an internal and external examiner.
09. COURSE OVERVIEW
The Mechanical Engineering Department has well established facilities for carrying out
the activities of basic mechanical engineering. It is equipped to meet the present day
technological advances and to meet the industrial requirements matching with the global
standards. The department has the state of the art laboratories to meet the demand for
practical knowledge by the present day industrial applications.
One of the oldest, largest and diversified of all engineering disciplines is mechanical
engineering. Rated as one of the most "evergreen" branches, students of mechanical
engineering can look forward to an exciting and robust study in the field of Thermal,
Design, Materials and Manufacturing Engineering. A Holistic blend of both theory and
practicals ensure that students are ready to face the challenges of the industrial world.
10. COURSE OBJECTIVE

The goal of our program is to prepare our graduates for successful professional practice and
advanced studies by providing a broad education in mechanical engineering and by offering the
opportunity to deepen their technical understanding in a particular concentration area of related
technical electives. Following are the course objectives.
1. Join a technically sophisticated workforce as successful, practicing engineers in a wide

range of mechanical engineering fields.
2. Continuously improve and expand their technical and professional skills through
formal means as well as through informal self-study.
3. Pursue advanced degrees in engineering, business, or other professional fields.
4. Advance themselves professionally and personally by accepting responsibilities and
pursuing leadership roles.
11. TEACHING PEDAGOGY

Our teaching methodology ensures that students are being exposed to a holistic education
experience in an active and dynamic learning environment, giving them the opportunity to
identify and realize their potential, and to achieve excellence. In order to realize the
objectives, a methodology based on the combination of the following will be adopted:
1. Team/Class room teaching.
2. PowerPoint presentations and handouts.
3. Simulated situations and role-plays.
4. Video films on actual situations.
5. Assignments.
6. Case Studies.
7. Exercises are solved hands on.
8. Seminars
9. Industry / Field visits.
10. Information and Communication Technology.
11. Project work.
12. Learning Management System.

12. ASSESSMENT RULES
 Assessment of Project Work
o Continuous Internal Assessment:100 Marks
 Presentation assessed by Panel Members
 Assessment by the guide
o End Semester Examination:100 Marks
 Viva Voce
 Demonstration
 Project Report
 Assessment of Comprehension
 Assessment of Seminar
o Continuous Internal Assessment:50 Marks
 Seminar on topics on emerging and thrust areas –minimum two seminars
 Student’s presentation on topics studied during their course
 Topics to be approved by the department
 Presentation assessed by Panel Members of Department
13. BRIEF OF PHYSICS AND CHEMISTRY CYCLE:
 B. Tech first year is followed by two semesters and each semester is divided into
two Cycles i.e. Physics Cycle and Chemistry Cycle.
 Accordingly, All First year students are also divided among both Physics Cycle
and Chemistry Cycle.
 The students in Physics Cycle will be moved to Chemistry Cycle and the
Chemistry Cycle students will be moved to Physics Cycle respectively in next
Semester (i.e. Second semester).

14. QUESTION PAPER PATTERN:
End Semester Examination (ESE) :

Theory Papers:
The ESE is conducted for 100 marks of 3 hours duration.

The syllabus for the theory papers is divided into FIVE units and each unit carries equal weightage
in terms of marks distribution.
Question paper pattern is as follows.

Two full questions with either or choice will be drawn from each unit. Each question carries 20
marks. There could be a maximum of three sub divisions in a question. The emphasis on the
questions is broadly based on the following criteria:50 % - To test the objectiveness of the concept
30 % - To test the analytical skill of the concept 20 % - To test the application skill of the concept
Laboratory / Practical Papers:

 The ESE is conducted for 50 marks of 3 hours duration.
 Writing, Execution and Viva - voce will carry weightage of 20, 20 and 10
respectively.
Mid Semester Examination (MSE) :

Theory Papers:
 The MSE is conducted for 50 marks of 2 hours duration.
 Question paper pattern; Five out of Six questions have to be answered. Each
question carries 10 marks.
Laboratory / Practical Papers:
The MSE is conducted for 50 marks of 2 hours duration. Writing,
Execution and Viva - voce will carry weightage of20,20 and 10 respectively.
Holistic Education:
End Semester Examination 25 Marks
Participation 25 Marks
Total 50 Marks

15. COURSE STRUCTURE:

B.Tech MECHANICAL
I SEMESTER
CHEMISTRY CYCLE
S. No. Course No. Course Name Marks Credit

1 MA131 Mathematics – I 100 4
2 CH132 Engineering Chemistry 100 4
3 EC133 Basic Electronics 100 4
4 CS134 Computer Concepts & C Programming 100 4
5 ME135 Elements of Mechanical Engineering 100 4
6 HE171 Holistic Education-I --- 1
7 ME151 Workshop Practice 50 2
8 CS152 Computer Programming Lab 50 2
9 CH153 Engineering Chemistry Lab 50 2
TOTAL 650 27
I SEMESTER
PHYSICS CYCLE
S. No. Course Code Course Name Marks Credits
1 MA131 Mathematics – I 100 4
2 PH132 Engineering Physics 100 4
3 EE133 Basic Electrical Engineering 100 4
4 CV134 Engineering Mechanics 100 4
5 EG135 Engineering Graphics 100 4
6 PD136 Professional Development-I 100 4
7 HE171 Holistic Education-I 1
8 PH151 Engineering Physics Lab 50 2
9 EE152 Basic Electrical Engineering Lab 50 2
TOTAL 700 29

SEMESTER II
CHEMISTRY CYCLE

1 MA231 Mathematics – II 100 4
2 CH232 Engineering Chemistry 100 4
3 EC233 Basic Electronics 100 4
4 CS234 Computer Concepts & C 100 4
Programming
5 ME235 Elements of Mechanical Engineering 100 4
6 HE271 Holistic Education-II 1
7 ME251 Workshop Practice 50 2
8 CS252 Computer Programming Lab 50 2
9 CH253 Engineering Chemistry Lab 50 2
TOTAL 650 27
SEMESTER II
PHYSICS CYCLE

1 MA231 Mathematics – II 100 4
2 PH232 Engineering Physics 100 4
3 EE233 Basic Electrical Engineering 100 4
4 CV234 Engineering Mechanics 100 4
5 EG235 Engineering Graphics 100 4
6 PD236 Professional Development-I 100 4
7 HE271 Holistic Education-II --- 1
8 PH251 Engineering Physics Lab 50 2
9 EE252 Basic Electrical Engineering Lab 50 2
TOTAL 700 29

SEMESTER III
S. No Course No Course Name Marks Credit
1 ME331 Mathematics -III 100 4

2 ME332 Material Science and Metallurgy 100 4
3 ME333 Basic Thermodynamics 100 4
4 ME334 Mechanics of Materials 100 4
5 ME335 Manufacturing Process-I 100 4
6 ME336 Professional Development 100 4
7 ME351 Metallographic &Material Testing 50 2
Laboratory
8 ME352 Foundry & Forging Laboratory 50 2
9 HE371 Holistic Education-III ---- 1
TOTAL 700 29
SEMESTER IV
1 ME431 Mathematics-IV 100 4
2 ME 432 Applied Thermodynamics 100 4
3 ME433 Kinematics of Machines 100 4
4 ME434 Manufacturing Process-II 100 4
5 ME435 Fluid Mechanics 100 4
6 ME436 Mechanical Measurements and 100 4

Metrology
7 ME451 Mechanical Measurements and 50 2
Metrology Laboratory
8 ME452 Machine Shop 50 2
9 HE471 Holistic Education-IV ---- 1
TOTAL 700 29

SEMESTER V
1 ME531 Design of Machine Elements-I 100 4
2 ME532 Energy Engineering 100 4
3 ME533 Dynamics of Machines 100 4
4 ME534 100 4
Turbo Machines
5 ME535 Manufacturing Process-III 100 4
6 ME536 Computer Aided Machine Drawing 100 4
7 ME551 Fluid Mechanics and Machines 50 2

Laboratory
8 ME552 Energy Conversion Engineering 50 2
Laboratory
TOTAL 700 28
SEMESTER VI
1 ME31 Design of Machine Elements – II 100 4
2 ME632 Heat and Mass Transfer 100 4
3 ME633 Finite Element Methods 100 4
4 ME634 Mechatronics & Microprocessor 100 4
5 ME635 Elective-I 100 4
6 ME636 Hydraulics and Pneumatics 100 4
7 ME651 Heat & Mass Transfer Laboratory 50 2
8 ME652 Computer Aided Modeling and Analysis 50 2

Laboratory
TOTAL 700 28

SEMESTER VII
(2012-13, 2013-14 and 2014-15 batches only)
1 ME731 Engineering Economy 100 4

2 ME732 Mechanical Vibrations 100 4
3 ME733 Operations Research 100 4
4 ME734 Industrial Robotics 100 4
5 ME735 Elective-II 100 4
6 ME736 Elective-III 100 4
7 ME751 Design Laboratory 50 2
8 ME752 CIM & Automation Laboratory 50 2
9 ME771 Internship -- 2
TOTAL 700 30
VII Sem
(2010-11, 2011-12 batches only)
1 ME731 Engineering Economy 100 4

2 ME732 Mechanical Vibrations 100 4
3 ME733 Operations Research 100 4
4 ME734 Industrial Robotics 100 4
5 ME735 Elective-II 100 4
6 ME736 Elective-III 100 4
7 ME751 Design Laboratory 50 2
8 ME752 CIM & Automation Laboratory 50 2
TOTAL 700 28

SEMESTER VIII
(2011-12, 2012-13, 2013-14 and 2014-15 batches)
1 ME 831 Operations Management 100 4
2 ME832 Control Engineering 100 4
3 ME833 Elective-IV 100 4
4 ME871 Project Work 200 6
5 ME872 Comprehension 50 2
6 BTCY01 Cyber Security -- 2
TOTAL 550 22
LIST OF ELECTIVES
ELECTIVE- I (ME635)
Course No Course Name Marks Credit
ME635 Theory of Elasticity 100 4
ME635 Mechanics of Composite Materials 100 4
ME635 Refrigeration and Air Conditioning 100 4
ME635 Design of Heat Exchanger 100 4
ME635 Non-Traditional Machining 100 4
ME635 Project Management 100 4
ME635 Statistical Quality Control 100 4

ELECTIVE –II (ME735)
ME735 Mechanism Design 100 4

ME735 Theory of Plasticity 100 4
ME735 Engineering Design 100 4
ME735 Gas Dynamics 100 4
ME735 Automation in Manufacturing 100 4
ME735 Total Quality Management 100 4
ELECTIVE-III (ME736)
ME736 Experimental Stress Analysis 100 4

ME736 Cryogenics 100 4
ME736 Smart Materials 100 4
ME736 Agile Manufacturing 100 4
ME736 Financial Management 100 4
ME736 Internal Combustion Engines 100 4
ELECTIVE –IV (ME833)
ME833 Tribology 100 4

ME833 Fracture Mechanics 100 4
ME833 Power Plant Engineering 100 4
ME833 Nanotechnology 100 4
ME833 Organizational Behavior & Professional 100 4
Communication
ME833 Automotive Engineering 100 4

MATHEMATICS - I MA 131
PAPER DESCRIPTION:
This paper contains five units which are Matrix Theory, Differential and Integral Calculus,
Differential Equation and Vector Calculus. This paper aims at enabling the students to know
various concepts and principles of calculus. Successive differentiation to any order, calculus of
functions of several variables, application of calculus to find area, volume etc and drawing
complicated curves, classification of different type of differential equation with an introduction
to vector calculus are covered in this paper.
PAPER OBJECTIVES:
This course is addressed to those who intend to apply the subject at the proper place and time,
while keeping him/her aware to the needs of the society where he/she can lend his/her expert
service, and also to those who can be useful to the community without even going through the
formal process of drilling through rigorous treatment of mathematics.
UNIT –I:
Matrix Theory 12 Hours
Basic concepts of matrix, matrix addition, scalar multiplication, matrix multiplication; Inverse
of a matrix; Determinants; Systems of linear equations, Eigenvalues, eigenvectors, and
applications, Cayley – Hamilton Theorem; Symmetric, skew-symmetric, and orthogonal
matrices, Hermitian, skew-Hermitian and unitary matrices; Properties of eigenvalues,
diagonalization
UNIT - II:
Differential Calculus - I 10 Hours
nth order derivative of standard functions. Leibnitz‟s theorem (without proof) and Problems.
Partial Derivatives, Euler‟s Theorem. Total differentiation. Differentiation of Composite and
implicit functions. Jacobians and their properties.
UNIT - III:
Integral Calculus – I 14 Hours
Reduction formulae for the integration of sin n x , cos n x , tan n x , cot n x , sec n x , cos ec n x and
sin mx cos nx and evaluation of these integrals with standard limits - Problems. Tracing of
standard curves in Cartesian, Parametric and Polar form.
Derivative of arc length, Applications of integration to find surfaces of revolution and volumes
of solids of revolution.
UNIT – IV:
Differential Equation - I 10 Hours
Solution of first order and first degree differential equations: homogeneous, linear, Bernoulli and
exact equations, Newton‟s law of cooling, Growth and Decay Problems.
UNIT –V:
Vector Calculus - I 14 Hours
Vector differentiation. Velocity, Acceleration of a particle moving on a space curve. Vector point
function. Gradient, Divergence, Curl, Laplacian. Solenoidal and Irrotational vectors - Problems.
ESSENTIAL READING
1. Dr. B. S. Grewal, “Higher Engineering Mathematics”, 39th Edition, Khanna Publishers,
July 2005.
2. K. A. Stroud, “Engineering Mathematics”, 6th Edition, Palgrave Macmillan, 2007.
RECOMMENDED READING
1. Erwin Kreyszig, “Advanced Engineering Mathematics”, 8th Edition, John Wiley & Sons, Inc,
2005
2. Thomas and Finney, “Calculus”, 9th Edition, Pearson Education, 2004
3. Peter V. O‟Neil, “Advanced Engineering Mathematics”, Thomson Publication, Canada, 2007
4. B. V. Ramana, “Higher Engineering Mathematics”, Tata McGraw – Hill, 2009.
5. Michael Artin, “Algebra”, 2nd Edition, Prentice Hall of India Private Limited, New Delhi,
2002
6. Kenneth Hoffman and Ray Kunze, “Linear Algebra”, 2nd Edition, Prentice Hall of India
Private Limited, New Delhi, 2002
7. George F. Simmons and Steven G. Krantz, “Differential Equation, Theory, Technique and
Practice”, Tata McGraw – Hill, 2006.
8. M. D. Raisinghania, “Ordinary and Partial Differential Equation”, Chand (S.) & Co. Ltd.,
India, March 17, 2005.
9. H. K. Das & Rajnish Verma, “Higher Engineering Mathematics”, S. Chand &
Company Ltd., 2011.

ENGINEERING CHEMISTRY – CH 132 / CH 232

(Common for all branches)
PAPER DESCRIPTION:
This paper contains five units which are Chemical Energy Sources, Solar Energy,
Electrochemical Energy Systems, Conversion and Storage of Electrochemical Energy Systems,
Corrosion of Science and Control. Metal finishing and Electroless plating, Liquid Crystals and
their Applications, High polymers and Water Technology. This paper aims at enabling the
students to know various energy sources. Corrosion and its control metal finishing. and method
of plating, crystals and their applications, types of polymers and water technology covered in this
paper.
PAPER OBJECTIVES:
 To familiarise the students on application oriented themes like the chemistry of materials
used in engineering discipline
 To focus the students on the chemistry of compounds resulting from pollution, waste
generation and environmental degradation and to apply the knowledge in solving these
current environmental problems effectively.
LEVEL OF KNOWLEDGE: Basic
UNIT – I: CHEMICAL ENERGY SOURCES 9 Hours
Introduction to energy; Fuels - definition, classification, importance of hydrocarbons as fuels;

Calorific value-definition, Gross and Net calorific values (SI units). Determination of calorific
value of a solid / liquid fuel using Bomb calorimeter. Petroleum cracking-fluidised catalytic
cracking. Reformation of petrol. Knocking - mechanism, octane number, cetane number,
prevention of knocking, anti-knocking agents, unleaded petrol; synthetic petrol – Bergius process
and Fischer Tropsch process; power alcohol. Solar Energy : Photovoltaic cells- Introduction,
definition, importance, working of a PV cell; solar grade silicon, physical and chemical
properties of silicon relevant to photovoltaics, production of solar grade (crystalline) silicon and
doping of silicon.
UNIT – II: ELECTROCHEMICAL ENERGY SYSTEMS (ELECTRODE POTENTIAL

AND CELLS) 7 Hours
Single electrode potential-definition, origin, sign conventions. Derivation of Nernst equation.

Standard electrode potential l-definition. Construction of Galvanic cell–classification - primary,
secondary and concentration cells, EMF of a cell–definition, notation and conventions.
Reference electrodes–calomel electrode, Ag/AgCl electrode. Measurement of single electrode
potential. Numerical problems on electrode potential and EMF. Ion-selective electrode- glass
electrode, determination of pH using glass electrode
CONVERSION AND STORAGE OF ELECTROCHEMICAL ENERGYBATTERY

TECHNOLOGY 7 Hours
Batteries-Basic concepts, battery characteristics. Classification of batteries–primary, secondary

and reserve batteries. Classical Batteries–Construction working and applications of Zn–air,
Nickel-Metal hydride and Lithium-MnO2 batteries, Fuel Cells - Introduction, types of fuel cells-
Alkaline, Phosphoric acid and Molten carbonate fuel cells. Solid polymer electrolyte and solid
oxide fuel cells. Construction and working of H2O2and Methanol-Oxygen fuel cell
UNIT – III: CORROSION SCIENCE 7 Hours

Corrosion - definition, Chemical corrosion and Electro-chemical theory of corrosion, Types of
corrosion, Differential metal corrosion, Differential aeration corrosion (pitting and water line
corrosion), Stress corrosion. Factors affecting the rate of corrosion, Corrosion control: Inorganic
coatings – Anodizing and Phosphating, Metal coatings –Galvanization and Tinning, Corrosion
Inhibitors, Cathodic and Anodic protection
METAL FINISHING 7 Hours

Technological importance of metal finishing. Significance of polarization, decomposition
potential and over-voltage in electroplating processes. Electroplating – Process, Effect of plating
variables on the nature of electro deposit, surface preparation and electroplating of Cr and Au.

Electroless Plating, Distinction between electroplating and electroless plating, advantages of

electroless plating. Electroless plating of copper on PCB and Nickel
UNIT – IV LIQUID CRYSTALS AND THEIR APPLICATIONS: 6 Hours

Introduction, classification-Thermotropic and Lyotropic with examples. Types of mesophases-
nematic, chiral nematic (cholesteric), smectic and columnar. Homologues series (PAA and
MBBA); Applications of liquid crystals in display systems
HIGH POLYMERS: 7 Hours

Definition, Classification - Natural and synthetic with examples. Polymerization – definition,
types of polymerization – Addition and Condensation with examples. Mechanism of
polymerization - free radical mechanism (ethylene as an example), Methods of polymerization -
bulk, solution, suspension and emulsion polymerization. Glass transition temperature, structure
and property relationship. Compounding of resins. Synthesis, properties and applications of
Teflon. PMMA, Polyurethane and Phenol – formaldehyde resin. Elastomers - Deficiencies of
natural rubber and advantages of synthetic rubber. Synthesis and application of Neoprene, Butyl
rubber. Adhesives- Manufacture and applications of Epoxy resins. Conducting polymers -
definition, mechanism of conduction in polyacetylene. Structure and applications of conducting
Polyaniline
UNIT – V WATER TECHNOLOGY: 7 Hours

Impurities in water, Water analysis - Determination of different constituents in water - Hardness,
Alkalinity, Chloride, Fluoride, Nitrate, Sulphate and Dissolved Oxygen. Numerical problems on
hardness and alkalinity. Biochemical Oxygen Demand and Chemical Oxygen Demand.
Numerical problems on BOD and COD. Sewage treatment. Potable water, purification of water -
Flash evaporation, Electro dialysis and Reverse Osmosis. Hazardous chemicals with ill effects
INSTRUMENTAL METHODS OF ANALYSIS: 2 Hours

Theory, Instrumentation and Applications of Colorimetry, Potentiometry, Conductometry

ESSENTIAL READINGS
1. Dr. B.S. Jai Prakash, “Chemistry for Engineering Students”, Subhas Stores, Bangalore,
Revised Edition 2009
2. M. M. Uppal, “Engineering Chemistry”, Khanna Publishers, Sixth Edition, 2001
3. Jain and Jain, “A text Book of Engineering Chemistry”, S. Chand & Company Ltd. New
Delhi, 2009
RECOMMENDED READING
(i) Alkins P.W. “physical chemistry” ELBS IV edition 1998, London

(ii) F. W. Billmeyer, “Text Book of Polymer Science”, John Wiley & Sons, 1994
(iii)G. W. Gray and P. A. Winsor, “Liquid crystals and plastic crystals”, Vol - I, Ellis
Horwood series in Physical Chemistry, New York. (P. No. 106-142)
(iv) M. G. Fontana, “Corrosion Engineering”, Tata Mc Graw Hill Publications 1994.
(v) Stanley E. Manahan, “Environmental Chemistry”, Lewis Publishers, 2000
(vi) B. R. Puri, L. R. Sharma & M. S. Pathania, ”Principles of Physical Chemistry”, S. Nagin
Chand & Co., 33rd Ed.,1992

BASIC ELECTRONICS – EC 133

PAPER DESCRIPTION:
The course aims to develop the skills of the students in the areas of electronics by
learning fundamentals. This will be necessary for their effective studies in a large number
of engineering subjects like Electronics circuits and devices, Digital Electronics,
communication systems. The course will also serve as a prerequisite for post graduate
and specialized studies and research.
PAPER OBJECTIVES:
 To impart basic knowledge about electronic and digital systems
 To give basic ideas about various communication systems
UNIT – I:
Introduction to semiconductors and basic diode theory 9 + 3 Hours
Conductors, semiconductors and insulators, Intrinsic and Extrinsic semiconductors, Flow of
charge carriers in a semiconductor, energy levels and barrier potential, PN junction as a diode,
Unbiased diode, forward bias diode, reverse bias, VI characteristics of a diode, Variation of
diode parameters with temperature. Ideal diodes, diode approximations, resistance of a diode,
Load lines, comparison between Silicon and Germanium
UNIT – II:
Semiconductor diode applications 9 + 3 Hours
Half-wave rectifier, ripple factor and efficiency, Full-wave and bridge rectifier, ripple factor and
efficiency, Peak inverse voltage, working of capacitor input filter, Approximate analysis of
capacitor filter, Zener diode characteristics, Zener and Avalanche breakdown, Zener diode
voltage regulator, power supply performance

UNIT – III :
Bipolar Junction Transistors 9 + 3 Hours
Bipolar junction transistor, transistor voltages and currents, Unbiased transistor, Biased
transistor, Transistor configurations- CB, CE, CC, DC load line Base Bias, Collector to Base
Bias, Voltage divider Bias, Comparison of basic bias circuits, Bias circuit design, Comparison
of basic bias circuits, Single stage CE amplifier, Decibel voltage gain, power gain, Half Power
points
UNIT – IV :
Introduction to Operational Amplifiers & Oscillators 9 + 3 Hours
Block diagram, Op-amp transfer characteristics, Basic Op-amp parameters and its value for IC
741- offset voltage and current, input and output impedance, Gain, slew rate, bandwidth, CMRR,
Concept of negative feedback, Inverting and Non-inverting amplifiers, Summing Amplifier,
Subtractor, integration, differentiation, Voltage follower, the Barkhausen Criterion for
Oscillations, BJT RC phase shift oscillator, Hartley Colpitts and crystal oscillator, Numerical
problems as applicable.
UNIT – V :
Digital Electronics 9 + 3 Hours
Introduction, decimal system, Binary, Octal and Hexadecimal number systems, addition and
subtraction, fractional number, Binary Coded Decimal numbers. Boolean algebra, Logic gates,
Half-adder, Full-adder, Parallel Binary adder.
ESSENTIAL READING
1. Albert Malvino, David. J. Bates, “Electronic Principles”, 7th Edition, Tata McGraw Hill,
2007
2. David. A. Bell, “Electronic Devices and Circuits”, PHI, New Delhi, 2004
3. Albert Paul Malvino, Donald P Leach, Goutamsaha, “Digital Principles and applications”, 6th
Edition, Tata McGraw Hill, 2007.

4. Roy Choudhary and Shail Jain, “Linear Integrated Circuits”,Third Edition,New Age
international Publishers,2007
RECOMMENDED READING
1. Jacob Millman, Christos C. Halkias “Electronic Devices and Circuits”, TMH, 1991 Reprint
2001
2. Morris Mano, “Digital Logic and Computer Design”, PHI, EEE

PROBLEM SOLVING AND PROGRAMMING CONCEPTS – CS 134

PAPER DESCRIPTION:
This paper contains five units which gives the programming concepts of C Language. This paper
aims at enabling the students to learn C programming Language in detail.
PAPER OBJECTIVES:
1. To develop skill in problem solving concepts through learning C programming.
Unit – I: 12 Hours
Algorithms and Flowcharts:
Algorithms, Flowcharts, Divide and conquer strategy. Examples on algorithms and flowcharts.
Constants, Variables, and Data types: Characters set, C tokens, Keywords and Identifiers,
Constants, Variables, Data types, Declaration of variables.
Operators and Expressions:

Arithmetic operators, Relational operators, Logical operators, Assignment operators, Increment
and Decrement operators, Conditional operator, Bitwise operators, Special operators, Arithmetic
expressions, Evaluation of expressions, Precedence of Arithmetic operators, Type conversions in
expressions, Operator precedence and associatively.
Unit – II: 12 Hours

Managing Input and Output Operations:
Reading a character, writing a character, Formatted Input, Formatted Output
Decision making and Branching:
Decision making with if statement, Simple if statement, The if…else statement, Nesting of
if…else statements, The else … if ladder, The switch statement, The ?: operator, The Goto
statement
Looping: The while statement, The do statement, The for statement, Jumps in Loops

Unit – III: 13 Hours

Arrays:
One-dimensional Arrays, Declaration of one-dimensional Arrays, Initialization of one-
dimensional Arrays, Two-dimensional Arrays, Initializing two-dimensional Arrays.
User-defined Functions:
Need for User-defined Functions, A multi-function Program, Elements of user - defined
Functions, Definition of Functions, Return Values and their types, Function Calls, Function
Declaration, Category of Functions, No Arguments and no Return Values, Arguments but no
Return Values, Arguments with Return Values, No Argument but Returns a Value, Functions
that Return Multiple Values.
Unit – IV: 10 Hours
Pointers:
Understanding the pointers, Accessing the Address of a Variable, Declaring Pointer Variables,
Initialization of Pointer Variables, Accessing a Variable through its Pointer, Pointer Expressions,
Pointer Increments and Scale Factor, Pointers and Arrays, Pointers and Character Strings,
Pointers as Function Arguments, Functions Returning Pointers.
Unit – V: 13 Hours
Strings, Structure, Union, Files:
Strings: String concepts, C strings, String I/O functions, Array of strings, String manipulation
function, Memory formatting, Derived types-Enumerated, Structure, and Union: The type
definition, Enumerated types, Structure, Accessing structures, Complex structures, Array of
structures, Structures and functions, Union , Files: Classification of Files, Standard Library
Functions for Files
ESSENTIAL READING:
1. Deitel and Deitel, "C How to Program", Prentice Hall 2010.
2. Anil Bikas Chaudhuri, "The Art of Programming through Flowcharts and Algorithms",
Firewall Media.

RECOMMENDED READING:
1. Introduction to Computer Science, ITL Education Solutions Ltd., Pearson Education,
2007.
2. E. Balagurusamy, “Programming in ANSI C”, Tata McGraw Hill – III Edition.
3. V. Rajaraman, “Fundamentals of Computers”, 4th Edition, PHI 2005.
4. M. G. V. Murthy, “Programming Techniques through C”, Pearson Education, 2007.
5. Yashvant Kanetkar, “Let Us C”, BPB Publications - 8th Edition, 2008.

ELEMENTS OF MECHANICAL ENGINEERING – ME135

PAPER DESCRIPTION:
Mechanical Engineering basically deals with three basic concepts Design engineering, Thermal
engineering & Manufacturing engineering, this subject ELEMENTS OF MECHANICAL
ENGINEERING gives the basic insight of theoretically knowledge of these aspects.
PAPER OBJECTIVES:
To familiarize with
(i) The Source of Energy and Power Generation.
(ii) The various metal processing and metal working.
(iii)The Basic theory of machine tools.

UNIT – I: 9 Hours
Energy and Steam Forms:
Sources and Classification of energy, Utilization of energy with simple block diagrams, Steam
formation. Types of steam, Steam properties – Specific Volume, Enthalpy and Internal energy.
(simple numerical problems) Steam boilers classification, Lancashire boiler, Babcock and Wilcox
boiler mountings, accessories, their locations and application. (No sketches for mountings and
accessories).
UNIT-II 16 Hours
TURBINES:
Steam turbines–Classification, Principle of operation of Impulse and reaction. Delaval‟s turbine,
Parson‟s turbine. Compounding of Impulse turbines. Gas turbines – Classification, Working
principles and Operations of Open cycle and Closed cycle gas turbines. Water turbines –
Classification, Principles and operations of Pelton wheel, Francis turbine and Kaplan turbine
INTERNAL COMBUSTION ENGINES:

Classification, I.C. Engines parts, 2/4 – Stroke Petrol and 4-stroke diesel engines. P-V diagrams
of Otto and Diesel cycles. Simple problems on indicated power, brake power, indicated thermal
efficiency, brake thermal efficiency, mechanical efficiency and specific fuel consumption.

UNIT – III: 9 Hours

REFRIGERATION AND AIR CONDITIONING:
Refrigerants, properties of refrigerants, list of commonly used refrigerants. Refrigeration -
Definitions - Refrigerating effect, Ton of Refrigeration, Ice making capacity, COP, Relative
COP, Unit of Refrigeration. Principle and working of vapor compression refrigeration and vapor
absorption refrigeration. Principles and applications of air conditioners, Room air conditioner
UNIT – IV: 16 Hours
LATHE AND DRILLING:
Machines Lathe - Principle of working of a Centre Lathe. Parts of a lathe. Operations on lathe -
Turning, Facing, Knurling, Thread Cutting, Drilling, Taper Turning by Tailstock offset method
and Compound slide swiveling method. Specification of Lathe.
Drilling Machine – Principle of working and classification of Drilling Machines. Bench Drilling
Machine, Radial Drilling Machine. Operations on Drilling Machine - Drilling, Boring, Reaming,
Tapping, Counter Sinking, Counter Boring and Spot facing. Specification of radial drilling
machine.
MILLING AND GRINDING MACHINES:
Milling Machine – Principle of Milling, Types of Milling Machines. Principle & Working of
Horizontal and Vertical Milling Machines. Milling Processes - Plane Milling, End Milling, Slot
Milling, Angular Milling, Form Milling, Straddle Milling and Gang Milling. Specification of
Universal Milling Machine.
Grinding Machine – Principle and classification of Grinding Machines. Abrasives - Definition,

types and Applications. Bonding Materials. Type of Grinding Machines, Principle and Working
of Surface Grinding, Cylindrical Grinding and Centerless Grinding.
UNIT – V: 10 Hours
JOINING PROCESSES, LUBRICATION AND BEARINGS:
Soldering, Brazing and Welding, Definitions. Classification and method of Soldering, Brazing
and Welding and Differences. Brief Description of Arc Welding and Oxy - Acetylene Welding
Lubrication and Bearings Lubricants - Classification and properties. Screw cap, Tell - Tale, Drop

feed, Wick feed and Needle Lubricators. Ring, Splash and Full pressure lubrication.
Classification of Bearings, Bushed bearing, Pedestal bearing, Pivot bearing, Collar Bearings and
Antifriction Bearings.
POWER TRANSMISSION: Belt Drives - Classification and applications, Derivations on

Length of belt. Definitions - Velocity ratio, Creep and slip, Idler pulley, stepped pulley and fast
& loose pulley. Gears - Definitions, Terminology, types and uses. Gear Drives and Gear Trains –
Definitions and classifications, Simple problems.
ESSENTIAL READINGS:
1. K.R. Gopalkrishna, “A text Book of Elements of Mechanical Engineering”,
Subhash Publishers, Bangalore.
2. S. Trymbaka Murthy, “A Text Book of Elements of Mechanical Engineering”,
3rd revised edition,I .K. International Publishing House Pvt. Ltd., New Delhi.
2010.
3. Dr. R. P. Reddy, N. Kapilan, “Elements of Mechanical Engineering”, 1st Edition,
Himalaya Publishing House, New Delhi.
1. SKH Chowdhary, AKH Chowdhary, Nirjhar Roy, “The Elements of Workshop
Technology”, Vol. I & II, Media Promotors and Publishers, Mumbai.
2. Ghosh Mallik, “Manufacturing Technology”, TMH. HMT, Production
Technology, TMH

HOLISTIC EDUCATION- HE 171

PAPER DESCRIPTION:
This paper contains three units which are Introduction to Life skills, Personal skills, Inter-
personal Skills and Societal Skills. This paper aims at enabling the students to various skills in
life.
PAPER OBJECTIVE:
 Holistic development of the individual adult in every student
 Knowing life and its principles
 Broadening the outlook to life
 Training to face the challenges of life
 Confidence creation and personality development
 Emotional control and stress management
 Creating awareness on duties, rights and obligations as member of the Society
 Realizing Personal Freedom-its limits and limitations
 Developing the attitude to be a contributor and giver
 Realizing the real happiness in life

1. INTRODUCTION TO LIFE SKILLS (I Semester) 4 Hours
2. PERSONAL SKILLS
 Creative thinking and Problem solving (I Semester)
 Critical thinking and Decision making(I Semester)
 Study skills and Time management(II Semester)
 Health (II Semester)
3. INTER-PERSONAL SKILLS 4 Hours
 Non verbal Communication(I Semester)
 Empathy and active listening(I Semester)
 Assertiveness Training (II Semester)
 Conflict Management(II Semester)

4. SOCIETAL SKILLS 4 Hours

 Human Rights(I Semester)
 Civil Society and Civic sense(I Semester)
 Equality and Justice(II Semester)
 Gender Sensation(II Semester)
ESSENTIAL READING: Holistic Education by Christ College publication, Bangalore-560029

WORKSHOP PRACTICE – ME 151

PAPER DESCRIPTION:
This paper provides working knowledge of fitting welding, sheet metal and carpentary.
PAPER OBJECTIVES:
To provide the students with the hands on experience on different trades of engineering like
fitting, welding, carpentary & sheet metal.
LEVEL OF KNOWLEDGE: Working

1. Fitting
a) Study of fitting tools
b) Study of fitting operations & joints
c) Minimum 5 models involving rectangular, triangular, semi circular and dovetail joints.
2. Welding
d) Study of electric arc welding tools & equipments
e) Minimum 4 Models - electric arc welding - Butt joint, Lap joint, T joint & L joint.
3. Sheet Metal
f) Study of development of surfaces
g) Minimum 03 models ( Tray,Funnel,Cone)
4. Study and demonstration of Carpentry tools, joints and operations.
ESSENTIAL READING:
S. K. H. Choudhury, A. K. H. Choudhury, Nirjhar Roy, “The Elements of Workshop
Technology”, Vol 1 & 2, Media Publishers, Mumbai

COMPUTER PROGRAMMING LABORATORY- CS152

PAPER DESCRIPTION:
Paper contains the programs which include Operations in C, Loop Control Structures, and
Function sand file handling methods. This paper aims at enabling the students to know
fundamentals of computer concepts and C programming.
PAPER OBJECTIVES:
 To impart the basic concepts of computer and information technology
 To develop skill in problem solving concepts through learning C programming in
practical approach.
LEVEL OF KNOWLEDGE: Basic/working
PART- A
 Write a C program to find and output all the roots of a given quadratic equation, for non-
zero coefficients. (Using if…else statement)
 Write a C program to simulate a simple calculator that performs arithmetic operations

like addition, subtraction, multiplication, and division only on integers. Error message
should be reported, if any attempt is made to divide by zero. (Using switch statement)
 Write a C program to generate and print first „N‟ Fibonacci numbers. (Using looping
constructs)
 Write a C program to find the GCD and LCM of two integers and output the results along
with the given integers. Use Euclid‟s algorithm. (Using looping constructs)

 Write a C program to reverse a given four digit integer number and check whether it is a
palindrome or not. Output the given number with suitable message. (Using looping
constructs)
 Write a C program to find whether a given number is prime or not. Output the given
number with suitable message. (Using looping constructs)
PART - B
 Write a C program to input N real numbers in into a single dimension array. Conduct
linear search for a given key integer number and report success or failure in the form of a
suitable message.
 Write a C program to input N integer numbers into a single dimension array. Sort them in
ascending order using bubble sort technique. Print both the given array and the sorted
array with suitable headings.
 Write a C program to evaluate the given polynomial f(x) = a4x4 +a3x3 + a2x2 + a1x1 + a0
for given value of x and the coefficients using Horner‟s method. (Using single dimension
arrays to store coefficients)
 Write a C program to input N real numbers in ascending order into a single dimension
array. Conduct a binary search for a given key integer number and report success or
failure in the form of a suitable message.
 Write a C program to input N integer numbers into a single dimension array. Sort them in
ascending order using bubble sort technique. Print both the given array and the sorted
array with suitable headings.
 Write C user defined functions
i. To input N real numbers into a single dimension array.
ii. Compute their mean.
iii. Compute their variance
iv. Compute their standard deviation.

Using these functions, write a C program to input N real numbers into a single dimension
array, and compute their mean, variance & standard deviation. Output the computed
results with suitable headings.
 Write C user defined functions

i. To read the elements of a given matrix of size M x N.
ii. To print the elements of a given matrix of size M x N.
iii. To compute the product of two matrices.
Using these functions, write a C program to read two matrices A(M x N) and B(P x Q)
and compute the product of A and B after checking compatibility for multiplication.
Output the input matrices and the resultant matrix with suitable headings and format
(Using two dimension arrays)
 Write a C program to read a matrix A(M x N) and to find the following using user
defined functions:
i. Sum of the elements of the specified row.
ii. Sum of the elements of the specified column.
iii. Sum of all the elements of the matrix.
Output the computed results with suitable headings.
 Write a C Program to create a sequential file with at least 5records, each record having
USN, name, mark1, mark2, and mark3. Write necessary functions
i. To display all the records in the file.
ii. To search for a specific record based on the USN. In case the record is not found,
suitable message should be displayed. Both the options in this case must be
demonstrated.

ENGINEERING CHEMISTRY LABORATORY- CH153 / CH253

PAPER DESCRIPTION:
This paper contains eleven experiments and aims at enabling the students to Practical
Engineering Chemistry.
PAPER OBJECTIVES:
1. To equip the students with the working knowledge of chemical principles, nature and
transformation of materials and their applications.
2. To develop analytical capabilities of students so that they can understand the role of
chemistry in the field of Engineering and Environmental Sciences
LEVEL OF KNOWLEDGE: Basic/working
(For Examination, one experiment from Part-A and Part-B shall be set. Different
experiments may be set from Part-A and common experiment from Part-B).
PART-A
1. Determination of viscosity coefficient of a given liquid using Ostwald‟s viscometer.
2. Estimation of copper by colorimetric method using spectrophotometer.
3. Conductometric estimation of strength of an acid using standard NaOH solution
4. Determination of pKa value of a weak acid using pH meter.
5. Potentiometric estimation of FAS using standard K2Cr2O7 solution.
PART-B
1. Determination of Total Hardness of a sample of water using disodium salt of EDTA.

2. Determination of Calcium Oxide (CaO) in the given sample of cement by Rapid EDTA
method.
3. Determination of percentage of Copper in brass using standard sodium thiosulphate solution.
4. Determination of Iron in the given sample of Haematite ore solution using potassium
dichromate crystals by
external indication method.
5. Determination of Chemical Oxygen Demand (COD) of the given industrial waste Water
sample. (for demonstration)

6. Determination of Dissolved Oxygen in the given water sample by Winkler method. (for
demonstration)
Examination – First experiment is a common experiment from Part B. Second experiment

is different, from Part A or Part B.
1. J. Bassett, R.C. Denny, G.H. Jeffery, “Vogels text book of quantitative inorganic analysis”,4th
Edition
2. SUNITA AND RATAN “PRACTICAL ENGINEERING CHEMISTRY”

MATHEMATICS – II MA231
Paper Description:
This paper contains five units which are Analytical Geometry in three dimensions, Differential
Calculus, Multiple integrals, Differential Equation of higher order and Laplace transformation
and its Inverse with Vector integration. This paper aims at enabling the students to study the
application of integration to various fields along with the different techniques to solve higher
order linear differential equation.
Paper objectives:
Mathematics is a necessary avenue to scientific knowledge which opens new vistas of mental
activity. A sound knowledge of engineering mathematics is a „sine qua non‟ for the modern
engineer to attain new heights in all aspects of engineering practice. This course provides the
student with plentiful opportunities to work with and apply the concepts, and to build skills and
experience in mathematical reasoning and engineering problem solving.
UNIT –I: Analytical Geometry in three dimensions 10 Hours

Direction cosines and direction ratios. Planes, Straight lines, Angle between planes / straight
lines, Coplanar lines. Shortest distance between two skew lines
UNIT – II: Differential Calculus – II 10 Hours

Polar curves and angle between Polar curves. Pedal equations of polar curves, Radius of
curvature – Cartesian, parametric, polar and pedal forms.
UNIT –III: Integral Calculus – II 12 Hours

Double integrals, Cartesian and polar co – ordinates, change of order of integration, change of
variables between cartesian and polar co – ordinates, triple integration, area as a double integral,
volume as a triple integral
UNIT –IV: Differential Equations - II and Vector Calculus – II 14 Hours

Linear differential equations of second and higher order with constant coefficients. Method of
undetermined coefficients. Method of variation of parameters.

Vector Integration - Green‟s theorem in a plane, Gauss‟s divergence theorems, Stoke‟s, (without
proof) and simple application.
UNIT -V: Laplace Transforms 14 Hours

Definition - Transforms of elementary functions. Derivatives and integrals of transforms-
Problems. Periodic function. Unit step function and unit impulse function Inverse transforms –
Properties. Solutions of linear differential equations
ESSENTIAL READING
July 2005.
2. K. A. Stroud, “Engineering Mathematics”, 6th Edition, Palgrave Macmillan, 2007.
RECOMMENDED READING
1. Erwin Kreyszig, “Advanced Engineering Mathematics”, 8th Edition, John Wiley &
Sons, Inc, 2005
2. Thomas and Finney, “Calculus”, 9th Edition, Pearson Education, 2004
3. Peter V. O‟Neil, “Advanced Engineering Mathematics”, Thomson Publication, Canada,
2007
4. B. V. Ramana, “Higher Engineering Mathematics”, Tata McGraw – Hill, 2009.
5. George F. Simmons and Steven G. Krantz, “Differential Equation, Theory, Technique and
Practice”, Tata McGraw – Hill, 2006.
India, March 17, 2005.
7. H. K. Das & Rajnish Verma, “Higher Engineering Mathematics”, S. Chand & Company
Ltd., 2011.

ENGINEERING PHYSICS – PH232

PAPER DESCRIPTION:
This paper contains five UNITs which are
 Modern Physics and Quantum Mechanics
 Conductivity in Metals( Electrical and thermal)
 Elastic, Dielectric, Magnetic and Optical Properties of Materials
 Lasers, Optical Fibers and Ultrasonics
 Crystal Structure and Modern Engineering materials.
This paper aims at enabling the students to know fundamentals covered in this paper.
PAPER OBJECTIVES:
 To impart the basic concepts and ideas in physics.
 To develop scientific attitudes and enable the students to correlate the concepts of
physics with the core programmes.
LEVEL OF KNOWLEDGE: Basic/working.
UNIT – I 14 Hours
Modern Physics
Introduction to Blackbody radiation spectrum - Planck‟s theory(qualitative) – Deduction of
Wien‟s displacement law and Rayleigh Jean‟s law from Planck‟s theory – Quantum theory
applied to Einstein‟s Photo-electric effect - Photo Multiplier Tube -Compton effect - Wave
particle Dualism -de Broglie hypothesis – de Broglie wavelength - extension to electron particle
– Davisson and Germer Experiment - Matter waves and their Characteristic properties. Phase
velocity, group velocity and Particle velocity. (qualitative).Elementary particles – QUARKS –
Types – Properties.
Quantum Mechanics
Heisenberg‟s uncertainty principle and its physical significance(no derivation). Application of
uncertainty principle (Non-existence of electron in the nucleus).
Wave function. Properties and Physical significance of a wave function Schroedinger‟s - Time
independent wave equation – Application: Setting up of a one dimensional Schrödinger wave

equation of a particle in a potential well of infinite depth : Probability density and Normalisation
of wave function – Energy eigen values and eigen function.
UNIT – II 11 Hours
Conductivity in metals – Electrical and Thermal
Classical free-electron theory. Assumptions. Drift velocity. Mean collision time and mean free
path. Relaxation time. Expression for drift velocity. Expression for electrical conductivity in
metals. Effect of impurity and temperature on electrical resistivity of metals. Failure of classical
free-electron theory. Thermal Conductivity. Wiedmann-Franz Law( relation between thermal
conductivity & electrical conductivity).
Quantum free-electron theory - Assumptions. Fermi - Dirac Statistics. Fermi-energy – Fermi
factor. Density of states (with derivation). Carrier concentration in metals. Expression for
electrical resistivity/conductivity Temperature dependence of resistivity of metals. Merits of
Quantum free – electron theory.
UNIT – III 12 Hours

Properties of Materials
Elasticity: Elasticity – types of moduli of elasticity – stress strain diagram – Young‟s modulus
of elasticity – rigidity modulus – bulk modulus – Poisson‟s ratio –Bending of beams – Single
Cantilever - Young‟s modulus-Non uniform bending.
Dielectric: Dielectric constant and polarisation of dielectric materials. Types of polarisation.
Equation for internal fields in liquids and solids (one dimensional). Clausius – Mossotti equation.
Ferro and Piezo – electricity(qualitative). Frequency dependence of dielectric constant. Important
applications of dielectric materials.
Optics : Phenomenon of diffusion, absorption and scattering of a light –
Snell‟s Law - Interference – thin films - Air wedge theory and experiment
Testing of flat surfaces. Anti reflection coating single and multi layer.
UNIT – IV 12 Hours
Lasers : Principle and production. Einstein‟s coefficients (expression for energy density).
Requisites of a Laser system. Condition for Laser action. Principle, Construction and working of

Nd YAG and semiconductor diode Laser. Applications of Laser – Laser welding, cutting and
drilling. Measurement of atmospheric pollutants.
Optical Fibers : Principle and Propagation of light in optical fibers. Angle of acceptance.
Numerical aperture. Types of optical fibers and modes of propagation. Applications – block
diagram discussion of point to point communication.
Ultrasonics : Ultrasonics production – Magnetostriction and Piezoelectric methods –
Application (NDT) non-destructive testing of materials- Flaw detection- Measurement of
velocity in liquids. Determination of elastic constants in liquids using Ultrasonic Interferometer.
UNIT - V
Material Science 12 Hours
Crystal Structure : Space lattice, Bravais lattice - UNIT cell, primitive cell. Lattice parameters.
Crystal systems. Direction and planes in a crystal. Miller indices. Expression for inter-planar
spacing. Co-ordination number. Atomic packing factor. Bragg‟s Law. Determination of crystal
structure by Bragg‟s x-ray spectrometer. Crystal structure of Na Cl.
Modern Engineering Materials:
Metallic Glasses: Properties – Applications.
Shape Memory Alloys : Characteristics - Applications.
Cryogenics : Properties – Applications.
Nano-materials : Molecular Manufacturing. Fabrication technology. Scaling of classical
mechanical systems – Basic assumptions. Mechanical scaling. Carbon nano-tubes.
ESSENTIAL READINGS:
1. M.N.Avadhanulu and P.G. Kshirsagar, “A Text Book of Engineering Physics”, S.Chand &
Company Ltd, 9th Edition 2012.
2. S.O. Pillai, “Solid State Physics”, New Age International, 6th Edition 2009.
3. S.P. Basavaraju, “ Engineering Physics”, Revised Edition 2009.
1. R.K. Gaur and S.L. Gupta, "Engineering Physics", Dhanpatrai and Sons,
New Delhi, 2001.

2. Sehgal Chopra Sehgal, “ Modern Physics ", Tata McGraw-Hill,

6th Edition, 2005.
3. Halliday, Resnick and Krane, "Fundamentals of Physics Extended", John Wiley and Sons
Inc., New York, 5th Edition, 1997.
4. P.Mani, “Engineering Physics”, Dhanam publishers, Revised Edition 2011.
5. H.J. Sawant, "Engineering Physics", Technical Publications, 1st Edition, 2010.
6. V. Rajendran, “Engineering Physics”, Tata Mcgraw Hill Publishing Company Limited, 1 st
Edition, 2009.
7. K.Eric Drexler, “Nanosystems - Molecular Machinery, Manufacturing and Computation”,
John Wiely & Sons, 2005.
8. J David, N Cheeke , “Fundamentals and Applications of Ultrasonic Waves”, CRC Press 1st
Edition, 2002.
9. Frederick J Bueche and Eugene Hecht “Schaum Outline of Theory and Problems of
College Physics”, Tata McGraw-Hill, 11th Edition, 2012.

BASIC ELECTRICAL ENGINEERING –EE233

PAPER DESCRIPTION:
This paper contains five units which are Analysis of DC circuits, Single phase & three phase A C
circuits, DC and AC machines and transformers. This paper aims at enabling the students to
provide comprehensive idea about circuit analysis, working principles of machines covered in
this paper.
PAPER OBJECTIVES:
At the end of the course students will be able
o To understand the basic concepts of magnetic circuits, AC & DC circuits.
o To solve the electrical network using mesh and nodal analysis
o To understand the concept of active, reactive and apparent powers, power factor and
resonance in series and parallel circuits.
o To know the basic concepts of three phase loads and power measurement.
o To explain the working principle, construction, applications of DC & AC machines
UNIT – I 12 Hours
Introduction to electrical power generation and distribution
ELECTRIC CIRCUIT ELEMENTS:

Sources: Ideal voltage source, practical voltage source, ideal current source, practical current
source, source transformation, Controlled sources.
Resistor: Resistance, linear and non-linear resistors, resistors in series, resistors in parallel,
current division, power consumed by a resistor.
Capacitor: Capacitance, equivalent capacitance of capacitors in series, voltage division,
capacitors in parallel, energy stored by a capacitor.
Inductor: Inductance, self-induced emf, energy stored by an inductor, inductors in series,
inductors in parallel mutual Inductance, Co-efficient of coupling.
Resistive networks: star- delta and delta – star transformations, network reduction technique.

SINGLE-PHASE AC CIRCUITS:
Alternating voltages and currents, generation of single phase alternating voltage, average value
and rms value of periodic sinusoidal and non- sinusoidal wave forms, form factor.
Representation of time-varying quantities as phasors; the operator j; Representation of complex
quantities; Addition, subtraction, multiplication and division of phasors.
Basic ac circuits, sinusoidal alternating current in a pure resistor, pure inductor and a pure
capacitor, waveforms of voltage, current, and power, phasor diagram, inductive and capacitive
reactances.
RL, RC, and RLC circuits, concept of impedance and phasor diagram, expression for average
power, power factor, parallel ac circuits, conductance, susceptance and admittance, analysis of
series parallel circuits and phasor diagrams, active power, reactive power, and apparent power,
complex power and power triangle.
UNIT III 12 Hours
THREE-PHASE AC CIRCUITS:
Generation of 3-phase balanced sinusoidal voltages, waveform of 3-phase voltages, star and delta
connections, line voltage and phase voltage, line current and phase current, analysis of 3-phase
circuit with balanced supply voltage and with star/delta connected balanced loads, measurement
of active power using two-wattmeter method with balanced loads.
ELECTROMAGNETISM:
Introduction to electromagnetism, comparison of electrical circuit with magnetic circuit,
Magnetic flux, Flux density, Fleming's left hand rule, Faraday‟s laws, Fleming's right hand rule,
Lenz‟s law,
DC MACHINES:
Working principle of DC machine as a generator and motor. Constructional features. E.M.F.
equation of generator and illustrative examples. Back E.M.F. and torque equations of D.C.
motors. Types of D.C. motors.

UNIT – V 12 Hours
TRANSFORMERS: Types, constructional features, principle of operation, equation for induced
emf, transformation ratio, ideal transformer, transformer under no-load, losses, efficiency,
applications.
THREE-PHASE INDUCTION MOTORS:
Types, constructional details, production of rotating magnetic field, synchronous speed, principle
operation, slip, Necessity of a starter for 3-phase induction motor, Star –Delta starter.
ESSENTIAL READINGS:
1. Arthur Eugene Fitzgerald, David E. Higginbotham, Arvin Grabel, “Basic electrical
engineering: circuits, electronics, machines, controls”, McGraw-Hill, Fifth Edition.
2. E. Hughes; “Electrical Technology", 9th Edition”, Pearson, 2005.
1. Kothari D. P. & Nagarath I. J, “Basic Electrical Technology”, TMH, 2004
2. Rajendra Prasad, “Fundamentals of Electrical Engineering”, Prentice Hall of India Pvt Ltd.,
2005
3. K.A. Krishnamurthy and M.R Raghuveer, “Electrical, Electronics and Computer
Engineering”, 2nd Edition, T.M.H., 2001
4. D C Kulshreshtha, “Basic Electrical Engineering”, TMH.
5. Abhijit Chakrabarti, Sudipta Nath & Chandan Kumar Chanda, “Basic Electrical Engineering”,
TMH, 2009.

ENGINEERING MECHANICS –CV 234

SUBJECT DESCRIPTION:
This paper aims at enabling the students to know the fundamentals Engineering Mechanics
covered in this paper. This paper contains five units which are Engineering Mechanics and its
classification, Composition of Forces, Equilibrium of Forces, Types of Supports, Analysis of
trusses, Centriod and Moment of Inertia and Friction.
SUBJECT OBJECTIVES:
o The students will understand the basics of Engineering Mechanics
o The students will understand the basic principles, laws, measurements, calculations
and SI units.
o The students will understand mechanics that studies the effects of forces and moments
acting on rigid bodies that are either at rest or moving with constant velocity along a
straight path for static condition only.
o The students will understand the basic concepts of forces in the member, centriod,
moment of inertia & friction
UNIT – I: 15 Hours
INTRODUCTION TO ENGINEERING MECHANICS
Basic idealizations – Practical, Continuum, Rigid body and Point force; Newton‟s laws of
motion, Definition of force, Introduction to SI units, Elements of a force, classification of force
and force systems; Principle of physical independence of forces, Principle of superposition of
forces, Principle of transmissibility of forces; Moment of a couple, characteristics of couple,
Equivalent force – couple system; Resolution of forces, composition of forces; Numerical
problems on moment of forces and couples, on equivalent force – couple system.

COMPOSITION OF FORCES: Definition of Resultant; Composition of coplanar – concurrent

force system, Principle of resolved parts; Numerical problems on composition of coplanar
concurrent force systems
COMPOSITION OF COPLANAR: Non-concurrent force system, Varignon‟s principle of
moments; Numerical problems on composition of coplanar non-concurrent force systems.
UNIT – II: 13 Hours
EQUILIBRIUM OF FORCES
Definition of Equilibrant; Conditions of static equilibrium for different force systems, Lami‟s
theorem; Numerical problems on equilibrium of coplanar – concurrent force system.
TYPES OF SUPPORTS: Statically determinate beams, Numerical problems on equilibrium of
coplanar-non- concurrent force system and support reactions for statically determinate beams
UNIT – III: 09 Hours

ANALYSIS OF PLANE TRUSSES
Introduction to Determinate and Indeterminate plane trusses - Analysis of simply supported and
cantilevered trusses by method of joints and method of sections
UNIT – IV: 15 Hours
CENTROID OF PLANE FIGURES
Locating the centroid of triangle, semicircle, quadrant of a circle and sector of a circle using
method of integration, centroid of simple built up sections; Numerical problems.
MOMENT OF INERTIA OF AN AREA: polar moment of inertia, Radius of gyration,
Perpendicular axis theorem and Parallel axis theorem; Moment of Inertia of rectangular, circular
and triangular areas from method of integration; Moment of inertia of composite areas;
Numerical problems.
UNIT – V: 08 Hours
FRICTION:
Types of friction, Laws of static friction, Limiting friction, Angle of friction, angle of repose;
Impending motion on horizontal and inclined planes; Wedge friction; Ladder friction; Numerical
problems.

ESSENTIAL READINGS
1. Bhavikatti S.S. “Elements of Civil Engineering (IV Edition) and Engineering
Mechanics”, 2/E, Vikas Publishing House Pvt. Ltd., New Delhi, 2008
2. Jagadeesh T.R. and Jay Ram, “Elements of Civil Engineering and Engineering
Mechanics”, 2/E, Sapana Book House, Bangalore, 2008.
3. Shesh Prakash and Mogaveer, “Elements of Civil Engineering and Engineering
Mechanics”, 1/E, PHI learning Private Limited, New Delhi, 2009.
1. Bansal R. K, “Engineering Mechanics”, Laxmi Publications(P) Ltd, New Delhi, 1995
2. Ferdinand P. Beer and E. Russel Johnston Jr., “Mechanics for Engineers: Statics”, 8/E,
McGraw-Hill Book Company, New Delhi. 2007
3. Goyal and Raghuvanshi., “Engineering Mechanics”, New Edition, PHI learning Private
Limited, New Delhi.
4. Irvingh H Shames, “Engineering Mechanics”, 4/E, PHI learning Private Limited, New
Delhi, 2008
5. Jivan khachane & Ruchishrivasatava, “Engineering Mechanics”, Ane‟s Student Edition,
Anne Book India, New Delhi, 2006.
6. Kolhapure B.K., “Elements of Civil Engineering & Engineering Mechanics”, 1/E, EBPB
Publications, Belgaum, 2003.
7. Lakshmana Rao, et al., “Engineering Mechanics - Statics and Dynamics”, New Edition,
PHI learning Private Limited, 2009.
8. Meriam J. L, and Kraige., L. G , “Engineering Mechanics”, 5/E, Volume I, Wiley India
Edition, India, 2009.
9. Nelson, “Engineering Mechanics”, New Edition, Tata McGraw-Hill Education Pvt. Ltd,
2009
10. Palanichamy M.S., “Engineering Mechanics (Statics & Dynamic)”, 3/E, Tata McGraw-
Hill Education Pvt. Ltd, New Delhi, 2008.
11. Sawant H. J, & Nitsure., “Elements of Civil Engineering (IV Edition) and Engineering
Mechanics”, New Edition, Technical publications, Pune, India, 2010.

ENGINEERING GRAPHICS – EG235

PAPER DESCRIPTION:
Provides basic knowledge about Orthographic projections, Projections of points, Projection of

lines, Projection of Planes and Projection of Solids, development of Surfaces & isometric
projections & also helps students learn Solid Edge.
PAPER OBJECTIVES:
o To draw and interpret various projections of 1D, 2D and 3D objects..
o To prepare and interpret the drawings.
o Hands on training in Solid Edge.
LEVEL OF KNOWLEDGE: Lettering and dimensioning
LEARNING OUTCOME:
o Will be in a position to convert vision /imagination into reality.
o Acquires knowledge of scaling.
o Can develop plan and elevation of geometrical objects.
o Can produce development of surfaces.
o Draw isomertic projection ofobjects.
UNIT - I 6 Hours
Introduction to Computer Aided Sketching:
Introduction, Drawing Instruments and their uses, BIS conventions, Lettering, Dimensioning and
free hand practicing. Computer screen, layout of the software, standard tool bar/menus and
description of most commonly used tool bars, navigational tools. Co-ordinate system and
reference planes. Definitions of HP, VP, RPP & LPP. Creation of 2D/3D environment. Selection
of drawing size and scale. Commands and creation of Lines, Co-ordinate points, axes, poly-lines,
square, rectangle, polygons, splines, circles, ellipse, text, move, copy, off-set, mirror, rotate, trim,
extend, break, chamfer, fillet, curves, constraints viz. tangency, parallelism, inclination and
perpendicularity. Dimensioning, line conventions, material conventions and lettering

Orthogonal Projections:
Introduction, Definitions - Planes of projection, reference line and conventions employed,
Projections of points in all the four quadrants, Projections of straight lines (located in First
quadrant/first angle only), True and apparent lengths, True and apparent inclinations to reference
planes (No application problems).
UNIT – III 15 Hours

Orthographic Projections of Plane Surfaces (First Angle Projection Only)
Introduction, Definitions – projections of plane surfaces – triangle, square, rectangle, rhombus,
pentagon, hexagon and circle, planes in different positions by change of position method only
(No problems on punched plates and composite plates)
PROJECTIONS OF SOLIDS:
Introduction, Definitions – Projections of right regular tetrahedron, hexahedron (cube), prisms,

pyramids, cylinders and cones in different positions. (No problems on octahedrons and
combination solid)
UNIT – V 15 Hours
SECTIONS AND DEVELOPMENT OF LATERAL SURFACES OF SOLIDS:
Introduction, Section planes, Sections, Section views, Sectional views, Apparent shapes and True
shapes of Sections of right regular prisms, pyramids, cylinders and cones resting with base on
HP. (No problems on sections of solids) Development of lateral surfaces of above solids, their
frustums and truncations. (No problems on lateral surfaces of trays, tetrahedrons, spheres and
transition pieces).
UNIT – VI 15 Hours
ISOMETRIC PROJECTION (USING ISOMETRIC SCALE ONLY):
Introduction, Isometric scale, Isometric projection of simple plane figures, Isometric projection
of tetrahedron, hexahedron(cube), right regular prisms, pyramids, cylinders, cones, spheres, cut
spheres and combination of solids (Maximum of three solids).

ESSENTIAL READINGS:
1. K.R. Gopalakrishna, “Engineering Graphics”, 15th Edition, Subash Publishers Bangalore.
2. Basant Agrawal, C. M. Agrawal, “Engineering Drawing”, TMH.
3. N.D. Bhatt, “Engineering Graphics, Elementary Engineering Drawing”, 48th Edition, Charotar
Publishing House, 2005.
4. S. Trymbaka Murthy, “Computer Aided Engineering Drawing”, I.K. International Publishing
House Pvt. Ltd., New Delhi.
5. P. J. Shah, “A Text Book og Engineering Graphics”, S. Chand & Company Ltd., New Delhi
6. Arunoday Kumar, “Engineering Graphics – I and II”, Tech – Max Publication, Pune.
7. T. Jeyapoovan, “Engineering Drawing & Graphics using Auro CAD 2000”, Vikas Publishing
Hoise Pvt. Ltd. , New Delhi.
8. R. K. Dhawan, “A Text Book of Engineering Drawing”, by S. Chand & Company Ltd., New
Delhi.
9. P. S. Gill, “A Text Book of Engineering Drawing”, S K Kataria & sons, Delhi.
10. D. A. Jolhe, “Engineering Drawing with an Introduction to Auto CAD”, D. A. Jolhe Tata
McGraw – Hill Publishing Co. Ltd., New Delhi.
11. S. Trymbaka Murthy, “Computer Aided Engineering Drawing”, I.K. International
Publishing House Pvt. Ltd., New Delhi.
NOTE: Examination comprise 30% manual drawing and 70% using software

PROFESSIONAL DEVELOPMENT–I PD236

AIM: The aim of the course is to develop effective oral and written business and
executive communication skills and negotiation strategies of the students and also in the
areas of boundary value problems and transform techniques.
OBJECTIVES
At the end of the course the students would
o Be capable of an acceptable level of oral and written communication.
o Be able to make effective presentations.
o Be able to apply negotiation strategies
o Be able to use technology advancements in communication.
EXECUTIVE AND BUSINESS COMMUNICATION

PART A – BUSINESS COMMUNICATION
UNIT 1 5 Hours
Introduction: Role of communication – defining and classifying communication – purpose of
communication – process of communication – characteristics of successful communication –
importance of communication in management – communication structure in organization –
communication in crisis
UNIT 2 5 Hours
Oral communication: What is oral Communication – principles of successful oral
communication – barriers to communication – what is conversation control – reflection and
empathy: two sides of effective oral communication – effective listening – non – verbal
communication
UNIT 3 9 Hours
Written communication: Functional English Grammar, Purpose of writing – clarity in writing –
Vocabulary – commonly confused and misused words, principles of effective writing –
approaching the writing process systematically: The 3X3 writing process for business

communication: Pre writing – Writing – Revising – Specific writing features – coherence –

electronic writing process.
UNIT 4 6 Hours
Business letters and reports: Introduction to business letters – writing routine and persuasive
letters – positive and negative messages- writing memos – what is a report purpose, kinds and
objectives of reports- writing reports
UNIT 5 6 Hours
Case method of learning: Understanding the case method of learning – different types of cases
– overcoming the difficulties of the case method – reading a case properly (previewing,
skimming, reading, scanning) – case analysis approaches (systems, Behavioural, decision,
strategy) – analyzing the case – dos and don‟ts for case preparation
UNIT 6 8 Hours
Presentation skills: What is a presentation – elements of presentation – designing a
presentation. Advanced visual support for business presentation- types of visual aid
Negotiations skills: What is negotiations – nature and need for negotiation – factors affecting
negotiation – stages of negotiation process – negotiation strategies
UNIT 7 6 Hours
Employment communication: Introduction – writing CVs – Group discussions – interview
skills
Impact of Technological Advancement on Business Communication
Communication networks – Intranet – Internet – e mails – SMS – teleconferencing –
videoconferencing
PART –B EXECUTIVE COMMUNICATION
UNIT 8 7 Hours
Group communication: Meetings – Planning meetings – objectives – participants – timing –
venue of meetings – leading meetings.
Media management – the press release- press conference – media interviews
Seminars – workshop – conferences.

Business etiquettes.
UNIT 9 8 Hours
Harnessing Potential & Developing Competencies in the areas of : Leadership Skills, Body
Language, Phonetics, Stress, Rhythm, Voice & Intonation, Eye Contact, Understanding
Personal Space, Team Building, Motivational Skills, Assertiveness Communication Skills,
Active Listening, Lateral & Creative Thinking, Cross Cultural Communication, Conflict
Resolution, Time Management, Stress Management, Selling Skills & Customer Relationship
Management, Appropriate Humour at the Workplace.
RECOMMENDED READINGS:
1. Business Communication : Concepts, Cases And Applications – P D Chaturvedi, Mukesh
Chaturvedi Pearson Education, 1/e, 2004 (UNIT 1, 2, 4, 5, & 7 )
2. Business Communication, Process And Product – Mary Ellen Guffey – Thomson
Learning , 3/E, 2002 (UNIT 3)
3. Basic Business Communication – Lesikar, Flatley TMH 10/E, 2005 (UNIT 1, 2, 4, 5, &
7)
4. Advanced Business Communication – Penrose, Rasberry, Myers Thomson Learning, 4/e,
2002 (UNIT 6 & 8)
5. Business Communication, M.K. Sehgal & V. Khetrapal, Excel Books.
6. Effective Technical Communication By M Ashraf Rizvi .- TMH, 2005
7. Business Communication Today by Bovee Thill Schatzman – Pearson & Education, 7th
Ed, , 2003
8. Contemporary Business Communication - Scot Ober-Biztanntra, 5/e
9. Business Communication – Krizan, Merrier, Jones- Thomson Learning, 6/e, 2005

HOLISTIC EDUCATION- HE271

PAPER DESCRIPTION:
This paper contains three units which are Introduction to Life skills, Personal skills, Inter-
personal Skills and Societal Skills. This paper aims at enabling the students to various skills in
life.
PAPER OBJECTIVE:
o Holistic development of the individual adult in every student
o Knowing life and its principles
o Broadening the outlook to life
o Training to face the challenges of life
o Confidence creation and personality development
o Emotional control and stress management
o Creating awareness on duties, rights and obligations as member of the Society
o Realizing Personal Freedom-its limits and limitations
o Developing the attitude to be a contributor and giver
o Realizing the real happiness in life
1. INTRODUCTION TO LIFE SKILLS (I Semester) 4 Hours
2. PERSONAL SKILLS
 Creative thinking and Problem solving (I Semester)
 Critical thinking and Decision making(I Semester)
 Study skills and Time management(II Semester)
 Health (II Semester)

3. INTER-PERSONAL SKILLS 4 Hours

 Non verbal Communication(I Semester)
 Empathy and active listening(I Semester)
 Assertiveness Training (II Semester)
 Conflict Management(II Semester)
4. SOCIETAL SKILLS 4 Hours

 Human Rights(I Semester)
 Civil Society and Civic sense(I Semester)
 Equality and Justice(II Semester)
 Gender Sensation(II Semester)
ESSENTIAL READING: Holistic Education by Christ College publication, Bangalore-560029

ENGINEERING PHYSICS LABORATORY – PH251

This paper contains twelve experiments and aims at enabling the students to Practical
Engineering Physics.
SUBJECT OBJECTIVES:
o To develop scientific and experimental skills of the students
o To correlate the theoretical principles with application based studies.
LEVEL OF KNOWLEDGE: Basic/working (Any 8 only)
1. Planck‟s Constant (Determination of Planck‟s constant using LED or using the principle
of photoelectric effect)
2. Verification of Stefan‟s law
3. Thermal Conductivity of a bad conductor – Lee‟s disc apparatus.
4. Determination of Fermi Energy
5. Young‟s modulus – Non-uniform bending/Strain gauge/Travelling Microscope
6. Measurement of Dielectric Constant( Charging & discharging of capacitor)
7. Interference at a wedge.
8. Laser Diffraction (Determination of grating constant and number of rulings per inch
using diffraction grating)
9. Ultrasonic Interferometer.
10. Frequency determination – Melde‟s apparatus
11. Magnetic properties (B-H Graph Method...........[Demo]
12. Particle size determination – Laser diffraction method...........[Demo]
ESSENTIAL READING:
1. Sathyaseelan H, “Laboratory Manual in Applied Physics”, New Age International, 3rd
Edition, 2012.
2. B.L.Worsnop and H.T.Flint, Advanced Practical Physics for Students, Methuen and Co.,
London, 9th Edition, 1957.
1. Engineering Physics Laboratory Manual for the First / Second Semester, Department of
Physics, R.V. College of Engineering, 2011.

ELECTRICAL ENGINEERING LABORATORY – EE252
This Laboratory contains twelve experiments and aims at enabling the students to learn the
concepts of electric circuits, machines, wiring, basic appliances, safety issues etc pertaining to
Electrical engineering.
SUBJECT OBJECTIVES:
o To develop scientific and experimental skills of the students
LIST OF EXPERIMENTS
1. Familiarization with Electrical Symbols, tools and materials.
2. Verification of Ohm‟s law.
3. Verification of Kirchhoff‟s Circuit laws. (KVL, KCL)
4. Two way control of lamp & Fluorescent Lamp
5. Two Way Plus Intermediate Switching Control Of Lamp And Fluorescent Lamp
6. Two Way Plus Intermediate Switching 3-Wire Control Of Lamp And Fluorescent Lamp
7. Measurement Of Single Phase Ac Power using RL Load
8. Measurement Of Power Factor Using Fluorescent Lamp
9. Error Calculations In Single Phase Energy Meter
10. O.C & S.C Tests On 1-φ Transformer.
1. Nagasarkar T. K. & Sukhija M. S., “Basic Electrical Engineering”, OUP 2005
2. Kothari D. P. & Nagarath I. J, “Basic Electrical Technology”, TMH 2004
3. Rajendra Prasad, “Fundamentals of Electrical Engineering”, Prentice Hall of India Pvt.
Ltd., 2005

SEMESTER III
MATHEMATICS - III ME331 (MA 1202)
Paper Description:
This paper contains five units which are Fourier Series, Fourier Transform, Partial Differential
Equation, Numerical Analysis and Calculus of Variation. This paper enables the students a solid
foundation upon the fundamental theorems and application of different transformations. It also
help the students to have an in depth knowledge of various advanced numerical methods and
interpolation techniques. Different methods to solve a partial differential equation and calculus
of variation are also covered in this paper.
Paper objective:
The course aims to develop the skills of the students in the areas of all engineering. This will be
necessary for their effective studies in a large number of engineering subjects.
UNIT – I: Fourier Series 12 Hours

Periodic functions, Dirichlet‟s conditions – General Fourier series – Odd and even functions –
Half range sine and cosine series – Complex form of Fourier Series – Harmonic Analysis.
UNIT – II: Fourier Transform 12 Hours
Fourier integral theorem (without proof) – Fourier transform pair – Sine and Cosine transforms –
Properties – Transforms of simple functions – Transform of the derivative and the derivative of
the transform - Convolution theorem – Parseval‟s identity.
UNIT-III: Partial Differential Equations 13 Hours
Formation of PDE, Solution of homogeneous PDE involving derivative with respect to one
independent variable only (Both types with given set of conditions), solution of non-
homogeneous PDE by direct integration, Method of separation of variables. (First and second
order equations) Solution of Lagrange‟s linear PDE of the type P p +Q q= R
Derivation of one dimensional wave and heat equations. Various possible solutions of these by
the method of separation of variables. D‟Alembert‟s solution of wave equation. Two dimensional

Laplace‟s equation – various possible solutions. Solution of all these equations with specified
boundary conditions. (Boundary value problems) Christ University Faculty of Engineering
UNIT-IV: Numerical Methods – I 12 Hours
Numerical solutions of algebraic and transcendental equations by Newton - Raphson and Regula
- Falsi methods. Solution of linear simultaneous equations: - Gauss elimination and Gauss Jordon
methods. Gauss – Seidel iterative method. Computation of largest eigen value and the
corresponding eigenvector by Rayleigh‟s power method.
Finite differences (Forward and Backward differences) Interpolation, Newton‟s forward and
backward interpolation formulae. Divided differences – Newton‟s divided difference formula.
Lagrange‟s interpolation and inverse interpolation formulae.
UNIT-V: Calculus of Variations 11 Hours
Variation of a function, Variational problems, Euler‟s equation and its solution, Standard
variation problems including geodesics, minimal surface of revolution, hanging chain and
Brachistochrone problems. Functional, functionals involving higher order derivatives.
ESSENTIAL READING:
1. Dr. B. S. Grewal, “Higher Engineering Mathematics”, 39th Edition, Khanna
Publishers, July 2005.
1. Erwin Kreyszig, “Advanced Engineering Mathematics”, 8th Edition, John Wiley &
Sons,Inc. 2005.
2. B.V. Ramana, “Higher Engineering Mathematics”, Tata-Macgraw Hill, 2009
3. Glyn James, “Advanced Modern Engineering Mathematics”, Pearson Education.
4. S. C. Malik, Savita Arora, “Mathematical Analysis”, 2nd Edition, New Age International
(P) Ltd., 2002.
5. George F. Simmons and Steven G. Krantz, “Differential Equation, Theory, Technique
and Practice”, Tata McGraw – Hill, 2006.
India, March 17, 2005
7. H. K. Das & Rajnish Verma, “Higher Engineering Mathematics”, S. Chand & Company
Ltd., 2011.

ME332 MATERIAL SCIENCE AND METALLURGY
Paper Description: Provides basic knowledge about engineering materials and metallurgy.
Paper Objectives:
o At the heart of materials science is an understanding of the micro structure of solids.
o Micro structure" is used broadly in reference to solids viewed at the subatomic
(electronic) and atomic levels, and the nature of the defects at these levels.
o To study the micro structures of solids at various levels, especially the defects, which
influences the mechanical, electronic, chemical, and biological properties of solids.
o To comprehend phenomenological and mechanistic relationships between the
microstructure and the macroscopic properties of solids , in essence, what the materials
science is all about.
Level of knowledge: Basic.
LEARNING OUTCOMES:
o Will be able to select material for engineering applications.
o Will be able to identify the material structures and determine its properties based on its
structures.
o Will have the knowledge of sub atomic and atomic structure of materials.
o Will be able to able to analyze the mechanical behavior of materials.
UNIT–1 12 Hours.
Crystal Structure: BCC, FCC and HCP Structures, coordination number and atomic packing
factors, crystal imperfections -point line and surface imperfections. Atomic Diffusion:
Phenomenon, Flick's laws of diffusion, factors affecting diffusion.
Mechanical Behaviour: Stress-strain diagram showing ductile and brittle behaviour of
materials, linear and non linear elastic behaviour and properties, mechanical properties in plastic
range, yield strength offset yield strength, dutility, ultimate tensile strength, toughness. Plastic
deformation of single crystal by slip and twinning.

UNIT – 2 12 Hours
Fracture: Type I, Type II and Type III.
Creep: Description of the phenomenon with examples. three stages of creep, creep properties,
stress relaxation.
Fatigue: Types of fatigue loading with examples, Mechanism of fatigue, fatigue properties,
fatigue testing and SN diagram.
UNIT – 3 12 Hours.
Solidification: Mechanism of solidification, Homogenous and Hetrogeneous nucleation, crystal
growth, cast metal structures.
Phase Diagram I: Solid solutions Hume Rothary rule substitional, and interstitial solid solutions,
intermediate phases, Gibbs phase rule.
Phase Diagram II: Construction of equilibrium diagrams involving complete and partial
solubility, lever rule. Iron carbon equilibrium diagram description of phases, solidification of
steels and cast irons, invariant reactions.
Heat treating of metals: TTT curves, continous cooling curves, annealing and its types.
normalizing, hardening, tempering, martempering, austempering, hardenability, surface
hardening methods like carburizing, cyaniding, nitriding, flarne hardening and induction
hardening, age hardening of aluminium-copper alloys.
UNIT -5 12 Hours.
Ferrous and non ferrous materials: Properties, Compostion and uses of
• Grey cast iron, malleable iron, S.G iron and steel
• Copper alloys-brasses and bronzes Aluminium alloys-Al-Cu,Al-Si,Al-Zn alloys.
Composite Materials: Definition, classification, types of matrix materials & reinforcements,

fundamentals of production of FRP' sand MMC's advantages and application of composites.

ESSENTIAL READING:
3. Foundations of Materials Science and Engineering, Smith, 3rd Edition McGraw Hill, 2009
4. Materials Science, Shackleford., & M. K. Muralidhara, Pearson Publication – 2007.
1. An introduction to Metallurgy; Alan Cottrell, University Press India Oriental Longman Pvt.
Ltd., 1974.
2. Engineering Materials Science, W.C.Richards, PHI, 1965
3. Physical Metallurgy; Lakhtin, Mir Publications
4. Materials Science and Engineering, V.Raghavan , PHI, 2002
5. Elements of Materials Science and Engineering, H. VanVlack, Addison- Wesley Edn., 1998
6. Materials Science and Engineering,William D. Callister Jr., John Wiley & Sons. Inc, 5th
Edition, 2001.
7. The Science and Engineering of Materials, Donald R. Askland and Pradeep.P. Phule, Thompson
Learning, 4lh Ed., 2003.

ME333 BASIC THERMODYNAMICS
Paper Description: Provides basic knowledge of thermal engineering.

Paper Objectives:
Thermodynamics is a basic science that deals with energy and energy changes. This course
covers the basic principles of Thermodynamics and presents real-world applications and
problems so that students can gain an understanding of physical and chemical changes that are
influenced by the energy of systems.
Level of Learning: Basic.
LEARNING OUTCOME:
o To explain energy conservation principle
o To balance different forms energies associated in a process
o To be able to analyse the conversion of heat in to work
o To be able to describe the direction and possibility of a process
o To be able to calculate the efficiency of device which converts heat into work and visa-
versa
o To be able to define ans describe entropy and entropy increase principle
o To be able to differentiate real and ideal gas
UNIT – 1 12 Hours
Fndamental Concepts & Definitions: Thermodynamis; definition and scope, Microscopic and
Macroscopic approaches. Engineering thermodynamics; definition, some practical applications of
engineering thermodynamic. System ( Closed system) and Control Volume (open system);
Characteristics of system boundary and control surface, examples. Thermodynamic properties;
definition and units, intensive and extensive properties. Thermodynamic state, state point, state
diagram, path and process, quasi-static process, cyclic and non-cyclic preesses; Thermodynamic
equilibrium; definition, mechanical equilibrium; diathermic wall, thermal equilibrium, chemical
equilibrium, Zeroth law of thermodynamics, Temperature; concepts, scales, measurement. Internal
fixed points.

UNIT – 2 13 Hours
Work and Heat: Mechancis, defintion of work and its limitations. Thermodynamic definition of
work; examples, sign convention. Displacement work; at part of a system boundary, at whole of a
system boundary, expressions for displacement work in various processes through p-v diagrams.
Shaft work; Electrical work. Other types of work. Heat; definition, units and sign convention, what
heat is not.
First Law of Thermodynamics: Joules expriments, equivalence of heat and work. Statement of the
First law of thermodynamics, extension of the First law to non - cyclic processes, energy, energy as a
property, modes of energy, pure substance; definition, two-property rule, Specific heat at constant
volume, enthalpy, specific heat constant pressure. Extension of the First law to control volume;
steady state-steady flow energy equation, important applications, analysis of unsteady processes such
as filmg and evacuation of vessels with and without heat transfer.
UNIT – 3 11 Hours
Second Law of Thermodynamics: Devices converting heat to work; (a) in a thermodynacmic

cycle, (b) in a mechanical cycle. Thermal reservoir. Direct heat engine; schematic representation
and efficiency. Devices converting work to heat in a theromodynamic cycle; reserved heat engine,
schematic representation, coefficients of performace. Keivin - Planck statement of the Secnd law of
Thermodynamics; PMM II and PMM I, Clasius statement of Second law of
Thermodynamics,Equivalence of the two statements; Reversible and irrevesible processes; factors
that make a process irreversible, reversible heat engines, Carnot cycle, Carnot principles.
Thermodynamic temperature scale.
UNIT – 4 13 Hours
Entropy: Clasius inequality; Statement, proof, application to a reversible cycle. Entropy;
definition, a property, principle of increase of entropy, entropy as a quantitative test for
irreversibility, calculation of entropy using Tds relations, entropy as a coordinate. Available and
unavailable energy.
Pure Substances: P-T and P-V diagrams, triple point and critical points. Sub-cooled liquid,
saturated liquid, mixture of saturated liquid and vapour, saturated vapour and superheated vapour
states of pure substance with water as example. Enthalpy of change of phase (Latent heat). Dryness

fraction (quality), T-S and H-S diagrams, representation of various processes on these diagrams.
Steam tables and its use. Throttling calorimeter, separating and throttling calorimeter.
UNIT – 5
Thermodynamic relations: Maxwell relation, Causius Clayperon's equation. Ideal gas; equation
of state, internal energy and enthalpy as functions of temperature only, universal and partiuclar gas
constans, specific heats, perfect and semi-perfect gases. Evaluation of heat, work, change in
internal energy. enthalpy and entropy in various quasi-static processes.
Ideal gas mixture : Ideal gas mixture;Dalton's laws of partial pressures, Amagat's law of additive
volumes, evaluation of properties, Analysis of various process. Real Gases: Introduction. Vander
Waal's Equation of state, Vander Waal's constants in terms of critical properties, law of
corresponding states, compressiblity factor; compressibility chart
ESSENTIAL READINGs:
1. Basic and applied thermodynamics, p.k.nag, tata mcgraw hul pub. 2002
2. Thermodynamcis, an engineering approach, yunus a.cenegal and michael

a.boles, tata mcgraw hill publications, 2002
1. K.A.Venkatesh Basic Engineering Thermodynomics, Thermodynomic data hand book by B.T.
Nijaguna. (To be supplied in the examination)
2. Engineering Thermodynamics, J.B.Jones and G.A.Hawkins, John Wiley and Sons..
3. Fundamentals of Cloassical Thermodynamics, G.J.Van Wylen and R.E.Sonntag, Wiley

Eastern.
4. An Introduction to Thermodynamcis, Y.V.C.Rao, Wiley Eastern, 1993,
5. B.K Venkanna “Basic Thermodynomics, PHI New Delhi

ME334 MECHANICS OF MATERIALS
PAPER DESCRIPTION: provides basic knowledge about forces acting on bodies.

PAPER OBJECTIVE:
o 1.The first objective of this course is to study the relationships between the external loads
applied to deformable body and the intensity of internal forces or stresses acting within
the body. it also involves the study of deformations or strains caused by external loads.
based on linear elastic material behavior you will be given sufficient
o 2.Understanding of the relationships between stress and strain in two and three
dimensions.
o 3.Understanding the yield criteria for static loading, fatigue and fracture under repetitive
loading will be covered to enable students design structures, machines and components.
o level of knowledge: basic.
UNIT 1: 13 Hours
Simple Stress and Strain: Introduction, Stress, strain, mechanical properties of materials,
Linear elasticity, Hooke's Law and Poisson's ratio, Stress-Strain relation - behavior in tension
for Mild steel, cast iron and non ferrous metals. Extension / Shortening of a bar, bars with
cross sections varying in steps, bars with continuously varying cross sections (circular and
rectangular), Elongation due to self weight, Principle of super position.
Stress in Composite Section: Volumetric strain, expression for volumetric strain, elastic
constants, simple shear stress, shear strain, temperature stresses (including compound bars).
UNIT 2: 12Hours
Compound Stresses: Introduction, Plane stress, stresses on inclined sections, principal
stresses and maximum shear stresses, Mohr's circle for plane stress.
Energy Methods: Work and strain energy, Strain energy in bar/beams, castiglinios theorem,
Energy methods.
Thick and Thin Cylinder Stresses in thin cylinders, changes in dimensions of cylinder
(diameter, length and volume). Thick cylinders Lame‟s equation (compound cylinders not
included).

UNIT 3: 11 Hours
Bending Moment and Shear Force in Beams: Introduction, Types of beams, loads and
reactions, shear forces and bending moments, rate of loading, sign conventions, relationship
between shear force and bending moments. Shear force and bending moment diagrams for
different beams subjected to concentrated loads, uniformly distributed load, (UDL) uniformly
varying load (UVL) and couple for different types of beams.
UNIT 4:
11HoursBending and Shear Stresses in Beams: Introduction, Theory of simple bending,
assumptions in simple bending. Bending stress equation, relationship between bending
stress,radius of curvature, relationship between bending moment and radius of
curvature.Moment carrying capacity of a section. Shearing stresses in beams, shear stress
across rectangular, circular, symmetrical I and T sections. (Composite / fletched beams not
included).
UNIT 5: 13 Hours
Deflection of Beams: Introduction, Differential equation for deflection. Equations for

deflection, slope and bending moment. Double integration method for cantilever and simply
supported beams for point load, UDL, UVL and Couple. Macaulay's method
Torsion of Circular Shafts and Elastic Stability of Columns: Introduction. Pure torsion,
assumptions, derivation of torsional equations, polar modulus, torsional rigidity / stiffness of
shafts. Power transmitted by solid and hollow circular shafts
Columns: Euler's theory for axially loaded elastic long columns. Derivation of Euler's load
for various end conditions, limitations of Euler's theory, Rankine's formula.

ESSENTIAL READING:
1. "Mechanics of materials", by R.C.hibbeler, printice hall. pearson edu., 2005
2. "Mechanics of materials", James.m.gere, thomson, fifth edition 2004.
3. "Mechanics of materials", in S.I. units, ferdinand beer & russell johnstan, tata
mcgrawhill- 2003.
1. S.S. Rattan, "Strength of Materials", Tata McGraw Hill, 2009
2. S.S.Bhavikatti, "Strength of Materials", Vikas publications House -1 Pvt. Ltd., 2nd Ed.,
2006.
3. " K.V. Rao, G.C. Raju, Mechanics of Materials", First Edition, 2007
4. "Engineering Mechanics of Solids", Egor.P. Popov, Pearson Edu. India, 2nd, Edison, 1998.
5. ", W.A. Nash, Strength of Materials Sehaum's Outline Series, Fourth Edition-2007.
6 Rajput.R.K. “Strength of Materials” S.Chand & co Ltd. New Delhi 1996
7 Bansal, R.K, Strength of Materials, Lakshmi Publication (P) Ltd, New Delhi.

ME335 MANUFACTURING PROCESS-I
Paper Description: Provides knowledge about primary manufacturing techniques.

Paper Objective:
The objective of studying Manufacturing process program is to provide students with an
understanding of specific advanced and emerging manufacturing technologies and skills relating
to the implementation of these technologies in modern industry within both global and local
contexts. It is expected that graduates will be sufficiently competent to direct the design and
implementation of specific technologies and/or processes addressed during the course in the
context of a particular organization.
Level of knowledge: Theoretical.
LEARNING OUTCOME:
o Will be able to describe the various casting process and can build his career in foundry.
o Will be able to explain the Special types of welding process, and will apply for fabrication
which require welding.
o Will be able to explain the Different Types of Soldering & Brazing Methods.
o Will be able to describe the Flame characteristics of welding process.
UNIT 1
Casting process:
Introduction: Concept of Manufacturing process, its importance. Classification of
Manufacturing processes. Introduction to Casting process & steps involved. Varieties of
components produced by casting process. Advantages & Limitations of casting process.
Patterns: Definition, functions, Materials used for pattern, various pattern allowances and their
importance. Classification of patterns, BIS colour coding of Patterns.
Binder: Definition, Types of binder used in moulding sand.
Additives: Need, Types of additives used.

UNIT 2
Sand Moulding : Types of base sand, requirement of base sand. Moulding sand mixture
ingredients (base sand, binder & additives) for different sand mixtures. Method used for sand
moulding, such as Green sand, dry sand and skin dried moulds.
Cores: Definition, Need, Types. Method of making cores, Binders used,core sand moulding.
Concept of Gating & Risering. Principle and types.
Fettling and cleaning of castings. Basic steps, Casting defects, Causes, features and remedies.
Moulding Machines : Jolt type, Squeeze type, Jolt & Squeeze type and Sand slinger.
UNIT 3:
Special moulding Process: Study of important moulding processes, No bake moulds, Flaskless
moulds, Sweep mould, CO2 mould, Shell mould, Investment mould.
Metal moulds: Gravity die-casting, Pressure die casting, Centrifugal casting, Squeeze Casting,
Slush casting, Thixocasting and Continuous Casting Processes.
Melting Furnaces: Classification of furnaces. Constructional features & working principle of
coke fired, oil fired and Gas fired pit furnace, Resistance furnace, Coreless Induction furnace,
Electric Arc Furnace, Cupola furnace.
UNIT 4
Welding
Welding process: Definition, Principles, Classification, Application, Advantages & limitations
of welding.
Arc Welding: Principle, Metal Arc welding (MAW), Flux Shielded Metal Arc Welding
(FSMAW), Inert Gas Welding (TIG & MIG) Submerged Arc Welding) (SAW) and Atomic
Hydrogen Welding processes. (AHW)
Gas Welding: Principle, Oxy – Acetylene welding, Chemical Reaction in Gas welding, Flame
characteristics. Gas torch construction & working. Forward and backward welding.
Special types of welding: Resistance welding - principles, Seam welding, Butt welding, Spot
welding and projection welding.

Friction welding, Explosive welding, Thermit welding, Laser welding and Electron beam
welding.
UNIT 5:
Metallurgical aspect, in welding : Structure of welds, Formation of different zones during
welding. Heat affected zone (HAZ). Parameters affecting HAZ. Effect of carbon content on
structure and properties of steel. Shrinkage in welds & Residual stresses.
Concept of electrodes, Filler rod and fluxes. Welding defects – Detection causes & remedy.
Principles of soldering & brazing: Parameters involved & Mechanism. Different Types of
Soldering & Brazing Methods.
Inspection Methods – Methods used for Inspection of casting and welding. Visual, Magnetic
particle, Fluorescent particle, Ultrasonic, Radiography, Eddy current, Holography methods of
Inspection.
ESSENTIAL READING
1. Dr.K.Radhakrishna, “Manufacturing Process-I”, Sapna Book House, 5th Revised Edition

2009.
2. P.N.Rao Manufacturing & Technology: Foundry Forming and Welding 2nd Ed., Tata
McGraw Hill, 2003.
1. Serope Kalpakjain, Steuen.R.Sechmid, “Manufacturing Technology”, Pearson Education

Asia, 5th Ed. 2006.
2. Roy A Lindberg, “Process and Materials of Manufacturing”, 4th Ed. Pearson Edu. 2006.

ME336 PROFESSIONAL DEVELOPMENT

Paper description
The aim of the course is to develop effective oral and written business and executive
communication skills, negotiation strategies of the students, inputs into problems and
transformational techniques and also to provide insight into Principles of Management.
Paper objectives
At the end of the course the students would
o Be capable of an acceptable level of oral and written communication.
o Be able to make effective presentations.
o Be able to apply negotiation strategies and understand Principles of management
o Be able to use technology advancements in communication.
LEARNING OUTCOME:
o Able to communicate orally and will have excellent written communication skills.
o Will have excellent presentation skills
o Will have excellent management capabilities and negotiation skills.
o Adopts the use of technological advancement in communication.
EXECUTIVE AND BUSINESS COMMUNICATION AND PRINCIPLES OF

MANAGEMENT
Part A – Business communication
MODULE 1 4 Hours
Introduction: Role of communication – defining and classifying communication – purpose of
communication – process of communication – characteristics of successful communication –
importance of communication in management – communication structure in organization –
communication in crisis

MODULE 2 4 Hours
Oral communication: What is oral Communication – principles of successful oral
communication – barriers to communication – what is conversation control – reflection and
empathy: two sides of effective oral communication – effective listening – non – verbal
communication
MODULE 3 8 Hours
Written communication: Functional English Grammar, Purpose of writing – clarity in writing –
Vocabulary – commonly confused and misused words, principles of effective writing –
approaching the writing process systematically: The 3X3 writing process for business
communication: Pre writing – Writing – Revising – Specific writing features – coherence –
electronic writing process.
MODULE 4 5 Hours
Business letters and reports: Introduction to business letters – writing routine and persuasive
letters – positive and negative messages- writing memos – what is a report purpose, kinds and
objectives of reports- writing reports
MODULE 5 4 Hours
Case method of learning: Understanding the case method of learning – different types of cases
– overcoming the difficulties of the case method – reading a case properly (previewing,
skimming, reading, scanning) – case analysis approaches (systems, Behavioural, decision,
strategy) – analyzing the case – dos and don‟ts for case preparation
MODULE 6 8 Hours
Presentation skills: What is a presentation – elements of presentation – designing a
presentation. Advanced visual support for business presentation- types of visual aid
Negotiations skills: What is negotiations – nature and need for negotiation – factors affecting
negotiation – stages of negotiation process – negotiation strategies

MODULE 7 6 Hours
Employment communication: Introduction – writing CVs – Group discussions – interview
skills-Impact of Technological Advancement on Business Communication,Communication
networks – Intranet – Internet – e mails – SMS – teleconferencing – videoconferencing
Part –B Executive communication

MODULE 8 7 Hours
Group communication: Meetings – Planning meetings – objectives – participants – timing –
venue of meetings – leading meetings.
Media management – the press release- press conference – media interviews
Seminars – workshop – conferences.
Business etiquettes.
MODULE 9 8 Hours
Harnessing Potential & Developing Competencies in the areas of : Leadership Skills, Body
Language, Phonetics, Stress, Rhythm, Voice & Intonation, Eye Contact, Understanding
Personal Space, Team Building, Motivational Skills, Assertiveness Communication Skills,
Active Listening, Lateral & Creative Thinking, Cross Cultural Communication, Conflict
Resolution, Time Management, Stress Management, Selling Skills & Customer Relationship
Management, Appropriate Humour at the Workplace.

1. Business Communication : Concepts, Cases And Applications – P D Chaturvedi, Mukesh
Chaturvedi Pearson Education, 1/e, 2004 (Module 1, 2, 4, 5, & 7 )
2. Business Communication, Process And Product – Mary Ellen Guffey – Thomson
Learning , 3/E, 2002 (Module 3)
3. Basic Business Communication – Lesikar, Flatley TMH 10/E, 2005 (Module 1, 2, 4, 5, &
7)
4. Advanced Business Communication – Penrose, Rasberry, Myers Thomson Learning, 4/e,
2002 (Module 6 & 8)
5. Business Communication, M.K. Sehgal & V. Khetrapal, Excel Books.
6. Effective Technical Communication By M Ashraf Rizvi .- TMH, 2005
7. Business Communication Today by Bovee Thill Schatzman – Pearson & Education, 7th
Ed, , 2003
8. Contemporary Business Communication - Scot Ober-Biztanntra, 5/e
9. Business Communication – Krizan, Merrier, Jones- Thomson Learning, 6/e, 2005
Part – C Principles of management
MODULE 10 (6 Hours)
Management: Introduction: Definition of management, nature, purpose and functions, level and
types of managers, Manager/Non-Manager, Managerial Roles, Essential Managerial Skills, Key
personal characteristics for Managerial success. Evolution and various schools to management
thoughts, continuing management themes – quality and performance excellence, global
awareness, learning organization, Characteristics of 21st century Executives. Social responsibility
of managers.
1. Management– J.R. Schermerhorn Jr. Wiley India, New Delhi 2004.
2. Management-Concepts and Cases-V.S.P.Rao, Excel Books
3. Management - A Global and Entrepreneurial Perspective - Harold Koontz, Heinz Weihrich -
TMH 12th edition, 2008.

ME351 METALLOGRAPHY & MATERIAL TESTING LABORATORY
PAPER DESCRIPTION: Provides working knowledge of material properties and testing

skills.
PAPER OBJECTIVE:
To develop skills in the field of material science.
o Verify the principles of the course
o Application of the theory , Understanding of fundamentals of the subject.
o Be in a position to relate theory and practice, Level of knowledge: Working.
This Laboratory has various experiments that aims at enabling the students to learn the concepts
of Material testing and metallographic analysis of specimens.
LEARNING OUTCOME:
o Will be able to identify materials of engineering importance, appreciate its application in
various engineering application.
o Will be able to test different materials for various mechanical properties.
o Will be able to carry out metallographic tests.
o To develop scientific, technical and experimental skills to the students.
PART – A
1. Preparation of specimen for Metallographic examination of different engineering materials.
Identification of microstructures of plain carbon steel, tool steel, gray C.I, SG iron, Brass,
Bronze & composites.
2. Heat treatment: Annealing, normalizing, hardening and tempering of steel. Hardness studies
of heat-treated samples.
3. To study the wear characteristics of ferrous, non-ferrous and composite materials for
different parameters.
4. Non-destructive test experiments like,

(a). Ultrasonic flaw detection

(b). Magnetic crack detection
(c). Dye penetration testing. To study the defects of Cast and Welded specimens
PART – B
1. Tensile, shear and compression tests of metallic and non metallic specimens using Universal
Testing Machine
2. Torsion Test
3. Bending Test on metallic and nonmetallic specimens.
4. Izod and Charpy Tests on M.S,C.I Specimen.
5. Brinell, Rockwell and Vickers‟s Hardness test.

6. Fatigue Test.

ME352 FOUNDRY & FORGING LABORATORY
PAPER DESCRIPTION:
Provides working knowledge on preparation of moulds, forging models and sand testing.
PAPER OBJECTIVES:
o Preparation of casting models, gating system design, die / pattern design and
mechanization of foundry.
o Aim is to provide insight of the subject.
o Sensitizes the students of the importance of course in real life environment.
of Foundry and Forging.
OUTCOME:
o Will have learnt the skill of developing the different types of moulds.
o Use of patterns.
o Preparing fasteners and mechanical elements through forging process.
o To develop scientific ,technical and experimental skills to the students
LEVEL OF KNOWLEDGE: Working.
PART – A
 Testing of Moulding sand and Core sand
Preparation of sand specimens and conduction of the following tests:

1. Compression, Shear and Tensile tests on Universal Sand Testing Machine.
2. Permeability test
3. Core hardness & Mould hardness tests.
4. Sieve Analysis to find Grain Finest number of Base Sand
5. Clay content determination in Base Sand

PART – B
 Foundry Practice
1. Use of foundry tools and other equipments.

2. Preparation of moulds using two moulding boxes using patterns or without patterns.
(Split pattern, Match plate pattern and Core boxes).
3. Preparation of one casting (Aluminum or cast iron-Demonstration only)
PART – C
 Forging Operations
1. Calculation of length of the row material requited to do the model.

2. Preparing minimum three forged models involving upsetting, drawing and bending
operations.
3. Out of these three models, at least one model is to be prepared by using Power
Hammer.

SEMESTER IV
ME431 MATHEMATICS IV (MA1253)
Paper description: This paper contains five units which are Numerical Methods, Complex
Variables, Series Solution of Differential Equation and Special Function with Statistics and
Probability. This paper emphasizes the basic concepts and methods of probability, discrete and
continuous random variables are considered.
Paper objective: The course aims to develop the skills of the students in the areas of all
engineering. This will be necessary for their effective studies in a large number of engineering
subjects and able to apply and solve problems arising in applications. The course will also serve
as a prerequisite for post graduate and specialized studies and research.
Level of knowledge: Basic
UNIT- I 7 Hours
Numerical methods-ii:
Numerical solutions of first order and first degree ordinary differential equations – Taylor‟s
series method, Modified Euler‟s method, Runge–Kutta method of fourth order, Milne‟s and
Adams-Bash forth predictor and corrector methods (All formulae without Proof).
UNIT- II 15 Hours
Complex variables:
Function of a complex variable, Limit, Continuity Differentiability – Definitions. Analytic
functions, Cauchy – Riemann equations in Cartesian and polar forms, Properties of analytic
functions. Conformal transformation – Definition. Discussion of transformations:
1
W  z 2 , W  ez , W  z  , Bilinear transformations. Complex line integrals, Cauchy‟s
z
theorem, Cauchy‟s integral formula. Taylor‟s and Laurent‟s series (Statements only)
Singularities, Poles, Residues, Cauchy‟s residue theorem (statement only)

UNIT- III 8 Hours

Series solution of ordinary differential equations and special functions:
Series solution – Frobenius method, Series solution of Bessel‟s D.E. leading to Bessel function
of fist kind. Equations reducible to Bessel‟s D.E., Series solution of Legendre‟s D.E. leading to
Legendre Polynomials. Rodirgue‟s formula
UNIT- IV 18 Hours
Probability & theoretical distributions:
Probability–Addition rule, conditional probability, multiplication rule, Bayes‟ theorem.
Random variables – Discrete and continuous random variables. Probability mass function (pmf),
Probability density function (pdf), cumulative distribution function (cdf), mean, variance, joint
probability distribution, Independent random variables. Expectation, Covariance, Correlation
coefficient
Theoretical distribution - Binomial, Poisson, Normal and Exponential distributions
UNIT-V
Statistical methods:
Curve fitting by the method of least squares: y  a  bx , y  a  bx  cx2 , y  axb , y  ab x ,
y  aebx , Correlation and Regression

Sampling, Sampling distribution, Standard error. Testing of hypothesis for means. Confidence
limits for means, Student‟s t distribution, Chi-square distribution as a test of goodness of fit.
ESSENTIAL READING:
July 2005.
2. Murray R. Spiegel, John Schiller, R. Alu Srinivasan, “Theory and Problems of
Probability and Statistics”, Schaum‟s series, Tata-Macgraw Hill, 2004.

1. Erwin Kreyszig, “Advanced Engineering Mathematics”, 8th Edition, John Wiley & Sons,
Inc.
2. B.V. Ramana, “Higher Engineering Mathematics”, Tata-Macgraw Hill
3. Glyn James, “Advanced Modern Engineering Mathematics”, Pearson Education.
4. Sheldon M. Ross, “Introduction to Probability Models”, 9th Edition, Academic Press,
2008

ME432 APPLIED THERMODYNAMICS

PAPER DESCRIPTION: Provides advanced knowledge about applications of thermodynamics
in the field of mechanical engineering.
PAPER OBJECTIVE:
To make the students understand thermodynamic principles, compressible flow and
fundamentals of heat transfer with its concepts in the operation of automotive engines.
Specifically, students will have the ability to apply the first and second law of thermodynamics to
(1) vapor power and refrigeration systems,
(2) gas power systems,
(3) applications concerning humidification, dehumidification, evaporative cooling, and
(4) thermodynamics of combustion systems such as furnaces, flow reactors etc.
LEVEL OF KNOWLEDGE: Basic of Thermodynamics

LEARNING OUTCOME:
o To demonstrate the principle of energy conversion.
o To do calculations on Quantity of energy conversion into useful work.
o To build real time models based on energy conversion principles.
o To judge a certain process can practically possible or not.
o To validate a process based on entropy principle.
UNIT 1: 12 Hours.
Combustion thermodynamics: Theoritical (Stoichiometeric) air for combustion of fuels.

Excess air, mass balance, actual combustion. Exhaust gas analysis. A./ F ratio, Energy balance for
a chemical reaction, enthalpy of formation, enthalpy and internal energy of combustion,
Combustion efficiency
I.C.Engine: Testing of two stroke and four stroke SI and CI engines for performance Related
numerical problems, heat balance , Morse test.

UNIT 2: 13 Hours.
Gas power cycle: Air Standard cycles: Carnot, Otto, Diesel, Dual and Stirling cycles,P-V and T-
S diagrams, description, efficiencies and mean effective pressures, Comparision of Otto and
Diesel cycles.
Vapour Power Cycles: Carnot vapour power cycles, drawbacks as a reference cycle, Simple
Rankine cycle, description, T- S diagram, analysis for performance , comparision of Carnot and
Rankine cycles. Effects of pressure and temperature on Rankine cycle performance. Actual
vapour power cycles. Ideal and practical regenerative Rankine cycle, open and closed feed water
heaters, Reheat Rankine cycle.
UNIT3: 13hours.
Reciprocating Compressors: Operation of a single stage reciprocating compressors, work input

through P-V diagram and steady state steady flow analysis. Effect of clearance and volumetric
efficiency. Adiabatic, isothermal and mechanical efficiencies. Multistage compressor, saving in
work, optimum intermediate pressure, inter- cooling, minimum work for compression.
Gas turbine and Jet propulsion: Classification of Gas turbines, Analysis of open cycle gas
turbine cycle. Advantages and disadvantages of closed cycle. Methods to improve thermal
efficiency, Jet propulsion and Rocket propulsion.
UNIT 4: 11 Hours.
Refrigeration: Vapour compression refrigeration system ; description, analysis, refrigerating

effect, capacity , power required, units of refrigeration, COP , Refrigerants and their desirable
properties. Air cycle refrigeration; reversed Carnot cycle, reversed Brayton cycle, Vapour
absorption refrigeration system, steam jet refrigeration.
UNIT 5: 11 Hours.
Psychrometry: Atmospheric air and psychrometric properties; Dry bulb temperature, wet bulb
temperature, dew point temperature; partial pressures, specific and relative humidifies and the
relation between the two enthalpy and adiapatic saturation temperature. Construction and use

of psychrometric chart . Analysis of various processes; heating, cooling , dehumidifying and

humidifying. Adiabatic mixing of moist air. Summer and winter air conditioning.
Note: Thermodynamics data hand book, B.T.Nijaguna (to be supplied in the examination)
1. A copy of Psychrometry chart to be given along with answer book to the candidates (if
needed)
ESSENTIAL READING
1. P.K. Nag Basic and applied Thermodynamics, , Tata Mc Graw Hill Pub.Co,2002
2. Applied Thermodynamics, Rajput, Laxmi Publication
3. B.K. Venkahna Applied Thermodynamics, , PHI, New Delhi
RECOMMENDED READING
1 Thermodynamics , An engineering approach, Yunus, A. Cenegal and Michael A.Boies,

Tata Me Graw Hill pub. Co., 2002,
2 Fundamental of Classical Thermodynamics, G.J. Van Wylen and R.E. Sontang Wiley
eastern.
3 B.K Venkanna “Applied Thermodynamics”, , PHI New Delhi

ME433 KINEMATICS OF MACHINES

Paper Description: Provides basic Knowledge of various mechanisms and forces acting on.
PAPER OBJECTIVE:
o The overall objective of this course is to learn how to analyze the motions of mechanisms,
design mechanisms to have given motions, and analyze forces in machines. This includes
relative motion analysis and design of gears, gear trains, cams, and linkages,
simultaneous graphical and analytical analysis of position, velocity, and acceleration,
considering static and inertial forces.
o This course reviews and reinforces the student's understanding of Kinematics and the
Dynamics of multi body systems with immediate application to the study of machines.
LEVEL OF UNDERSTANDING: Basic.
LEARNING OUTCOME:
o Familiarity with common mechanisms used in machines and everyday life.
o Ability to calculate mobility (number of degrees-of-freedom) and enumerate rigid links
and types of joints within mechanisms.
o Ability to conduct a complete (translational and rotational) mechanism position analysis.
o Ability to conduct a complete (translational and rotational) mechanism velocity analysis.
o Ability to conduct a complete (translational and rotational) mechanism acceleration
analysis.
o Ability to do gear mechanism classification and gear train analysis, and familiarity with
gear standardization and specification in design.
o Ability to do cam mechanism classification and cam motion profiles, and familiarity with
introductory cam design considerations.
UNIT 1: 13 Hours
Introduction: Definitions Link or element, kinematic pairs, Degrees of freedom, Grubler's

criterion (without derivation), Kinematic chain, Mechanism, Structure, Mobility of Mechanism,
Inversion, Machine.
Kinematic Chains and Inversions: Inversions of Four bar chain; Single slider crank chain and
Double slider crank chain.
Mechanisms: Quick return motion mechanisms-Drag link mechanism, Whitworth mechanism

and Crank and slotted lever Mechanism.
Straight line motion mechanisms Peaucellier's mechanism and Robert's mechanism. Intermittent
Motion mechanisms -Geneva wheel mechanism and Ratchet and Pawl mechanism. Toggle
mechanism, Pantograph, Ackerman steering gear mechanism.
UNIT 2: 11 Hours.
Velocity and Acceleration Analysis of Mechanisms (Graphical Methods) Velocity and

acceleration analysis of Four Bar mechanism, slider crank mechanism and Simple Mechanisms
by vector polygons: Relative velocity and acceleration of particles .in a common link, relative
velocity and accelerations of coincident Particles on separate links- Coriolis component of
acceleration. Angular velocity and angular acceleration of links, velocity of rubbing.
UNIT 3: 12 Hours.
Velocity Analysis by Instantaneous Center Method: Definition, Kennedy's Theorem,

Determination of linear and angular velocity using instantaneous center method
Klein's Construction: Analysis of velocity and acceleration of single slider crank mechanism.
Velocity and Acceleration Analysis of Mechanisms (Analytical Methods): Analysis of four
bar chain and slider crank chain using analytical expressions. (Use of complex algebra and
vector algebra)
UNIT 4: 13 Hours.
Spur Gears: Gear terminology, law of gearing, Characteristics of involute action, Path of
contact. Arc of contact, Contact ratio of spur, helical, bevel and worm gears, Interference in
involute gears. Methods of avoiding interference, Back lash. Comparison of involute and
cycloidal teeth. Profile Modification.
Gear Trains: Simple gear trains, Compound gear trains for large speed. reduction, Epicyclic
gear trains, Algebraic and tabular methods of finding velocity ratio of epicyclic gear trains.
Tooth load and torque calculations in epicyclic gear trains.

UNIT 5: 11 Hours.
Cams: Types of cams, Types of followers. Displacement, Velocity and, Acceleration time
curves for cam profiles. Disc cam with reciprocating follower having knife-edge, roller and flat-
face follower, Disc cam with oscillating roller follower. Follower motions including SHM,
Uniform velocity, uniform acceleration and retardation and Cycloidal motion.
ESSENTIAL READING:
1. Rattan S.S "Theory of Machines”, , Tata McGraw-Hill Publishing Company Ltd., New
Delhi, and 3rd edition -2009.
2. Sadhu Singh "Theory of Machines”, , Pearson Education (Singapore) Pvt. Ltd, Indian
Branch New Delhi, 2nd Edi. 2006
1. J.J. Uicker, , G.R. Pennock, J.E. Shigley. “Theory of Machines & Mechanisms",
OXFORD 3rd Ed. 2009.
2. Ambakar Mechanism and Machine theory, , PHI Graphical Solutions may be obtained
either on the Graph Sheets or on the Answer Book itself.

ME43 4MANUFACTURING PROCESS-II

PAPER DESCRIPTION: Provides knowledge about various manufacturing techniques.
PAPER OBJECTIVE:
o Subject provides students an understanding of basic, advanced and emerging
manufacturing technologies. Enables in relating to the implementation of these
technologies in modern industry within both global and local contexts.
o It makes the graduates sufficiently competent to direct the design and implementation of
specific technologies and/or processes addressed during the course in the context of a
particular organization.
LEVEL OF LEARNING: Basic
OBJECTIVES:
o Develop understanding of basis manufacturing processes and capabilities of each.

o Extend basis knowledge to solve manufacturing processes related problems.
o Develop an understanding of Concurrent Engineering and the importance to
manufacturing industries.
o Enhance ability to determine what is given and what to find.
o Learn to make engineering judgments.
o Learn the impact that modern manufacturing techniques have on human
advancement.
o Understand what manufacturing processes references are available.
o Discuss current manufacturing issues.
o Emphasize the problem solving process and application techniques.
LEARNING OUTCOME:
o Will be able to implement specific advanced and emerging manufacturing technologies in

modern industry.
o Will be able to describe the process of machining in various types of materials.

o Will describe the operations and utilization of lathe, drilling, milling, grinding machine,
etc.
o Will describe the tool nomenclature, and design the tool for specific operations.
o Will apply merchant‟s analysis for tool wear, failure and life.
UNIT - 1 13 Hours.
Theory of Metal Cutting: Single point cutting tool nomenclature, geometry. Mechanics of Chip
Formation,Types of Chips. Merchants circle diagram and analysis, Ernst Merchant‟s solution,
shear angle relationship, problems of Merchant‟s analysis. Tool Wear and Tool failure, tool life.
Effects of cutting parameters on tool life. Tool Failure Criteria, Taylor‟s Tool Life equation.
Problems on tool life evaluation.
Cutting Tool Materials: Desired properties and types of cutting tool materials – HSS, carbides
coated carbides, ceramics. Cutting fluids. Desired properties, types and selection. Heat
generation in metal cutting, factors affecting heat generation. Heat distribution in tool and
workpiece and chip. Measurement of tool tip temperature.
Turning (Lathe), Shaping and Planing Machines: Classification, constructional features of

Turret and Capstan Lathe. Tool Layout, shaping Machine, Planing Machine, Driving
mechanisms of lathe, shaping and planing machines, Different operations on lathe, shaping
machine and planing machine. Simple problems on machinery time calculations
UNIT-3 13 Hours.
Drilling machines: Classification, constructional features, drilling & related operations. Types
of drill & drill bit nomenclature, drill materials. Introduction to CNC machines- Principles of
operation. Axes of NC machine-Coordinate systems. Basics of Manual part programming
methods.
Milling machines: Classification, constructional features, milling cutters nomenclature, milling
operations, up milling and down milling concepts. Various milling operations.
Indexing: Simple, compound, differential and angular indexing calculations. Simple problems
on simple and compound indexing
UNIT - 4: 12 Hours.
Grinding machines: Types of abrasives,Grain size, bonding process, grade and structure of
grinding wheels, grinding wheel types. Classification, constructional features of grinding

machines (Centreless , cylindrical and surface grinding ). Selection of grinding wheel. Grinding
process parameters. Dressiing and truing of grinding wheels.
Broaching process - Principle of broaching. Details of a broach. Types of broaching machines-
constructional details. Applications. Advantages and Limitations.
Finishing and other Processes Laping and Honing operations – Principles, arrangement of set
up and application. Super finishing process, polishing, buffing operation and application.
Non-traditional machining processes: Need for non traditional machining, Principle,
equipment & operation of Laser Beam, Plasma Arc Machining, Electro Chemical Machining,
Ultrasonic Machining, Abrasive Jet Machining, Water Jet Machining, Electron Beam Machining,
Electron Discharge Machining and Plasma Arc Machining.
ESSENTIAL READING:
1. Hazara Choudhry, Workshop Technology, Vol-II, Media Promoters & Publishers Pvt. Ltd.
2004
2. R.K.Jain Production Technology, , Khanna Publications, 2003.
3. Production Technology, HMT, Tata MacGraw Hill, 2001.
1. Amitabha Ghosh and Mallik, Manufacturing Science, affiliated East West Press, 2003.
2. G. Boothroyd Fundamentals of Metal Machining and Machine Tools, , McGraw Hill, 2000.

ME435 FLUID MECHANICS

Paper Description: Provides basic knowledge about fluid at rest and in motion.
Paper Objectives:
This is a first course in fluid mechanics that involves the study of fluid flow in ducts. The course
introduces the fundamental aspects of fluid motion, fluid properties, flow regimes, pressure
variations, fluid kinematics, and methods of flow description and analysis. It presents the
conservation laws in their integral and differential forms, and their use in analyzing and solving
fluid flow problems.
o Determine distribution in fluids at rest and to calculate hydrostatic forces acting on
plane and curved surfaces.
o Determine pressure variation in a flowing fluid using Bernoulli's principle.
o Determine velocity and acceleration of a fluid at a point.
o Apply control volumes to solve fluid flow problems through the application of integral
conservation laws of mass, momentum, and energy.
o Apply the differential conservation equations of mass, momentum, and energy to fluid
flow problems.
o Apply basic fluid mechanics principles to the flow of viscous fluids in pipes and ducts.
Level of knowledge: Basic
UNIT-1 13 Hours.
Properties of Fluids: Introduction, Properties of fluids, viscosity, thermodynamic properties,

surface tension, capillarity, vapour pressure and cavitation
Fluid Statics : Fluid pressure at a point, Pascal‟s law, pressure variation in a static fluid,
absolute, gauge, atmospheric and vacuum pressures, simple manometers and
differentialmanometers. Total pressure and center of pressure on submerged plane surfaces;
horizontal, vertical and inclined plane surfaces, curved surface submerged in liquid.

UNIT-2 11 Hours.
Buoyancy and Fluid Kinematics:

Buoyancy, center of buoyancy, metacentre and metacentric height, conditions of equilibrium of
floating and submerged bodies, determination of Metacentric height experimentally and
theoretically.
Kinematics: Types of fluid flow, continuity equation in 2D and 3D (Carversian Co-ordinates
only, velocity and acceleration, velocity potential function and stream function.
UNIT-3 11 Hours.
Fluid Dynamics: Introduction equation of motion, Euler‟s equation of motion, Bernoulli‟s

equation from first principles and also from Euler‟s equation, limitations of Bernoulli‟s equation.
UNIT-4 13 Hours.
Fluid Flow Measurements : Venturimeter, orificemeter, pitot-tube, vertical orifice, V-Notch

and rectangular notches.
Dimensional Analysis : Introduction, derived quantities, dimensions of physical quantities,
dimensional homogeneity, Rayleigh‟s method, Buckingham  theorem, dimensionless numbers,
similitude, types of similtudes.
UNIT-5 12 Hours.
Flow through pipes : Minor losses through pipes. Darey‟s and Chezy‟s equation for loss of head
due to friction in pipes. HGL andTEL.
Flow past immersed bodies : Drag, Lift, expression for lift and drag, boundary layer concept,
displacement, momentum and energy thickness.
Introduction to compressible flow : Velocity of sound in a fluid, Mach nuber, Mach cone,
propogation of pressure waves in a compressible fluid.

ESSENTIAL READINGs:
1. Oijush.K.Kundu :Fluid Mechanics , IRAM COCHEN, ELSEVIER, 3rd Ed. 2005.
2. Dr. Bansal Fluid Mechancis , R.K.Lakshmi Publications, 2004.
2. Dr.Jagadishlal Fluid Mechanics and hydraulics,: Metropolitan Book Co-Ltd., 1997.
3. Yunus A. Cingel John M.Oimbala Fluid Mechanics (SI Units),. Tata MaGrawHill, 2006.
4. John F.Douglas, Janul and M.Gasiosek and John Fluid Mechanics A.Swaffield, Pearson
Education Asia, 5th ed., 2006
5. Fluid Mechanics and Fluid Power Engineering, Kumar.D.S, Kataria and Sons., 2004
6. Merle C. Potter, Elaine P.Scott Fluid Mechanics -.. Cengage learning

ME436 MECHANICAL MEASUREMENTS AND METROLOGY

PAPER DESCRIPTION: Provides basic knowledge about measurements.
PAPER OBJECTIVES:
o To study and understand the general concepts and terminologies of Measurement system,
Definition of measurement and measurand, Block diagram of measurement. Static and
Dynamic characteristics of measurement system.
o To study and understand Transducer Definition, Classification, and Performance
Characteristics
o To study and understand the principles of calibration- definition, traceability,
Infrastructural requirements of Calibration laboratory, Technical system requirements of
Calibration laboratory.
OUTCOME:
o To calibrate the measurement devices.
o To measure the angular measurements using Sine bar, Sine centre.
o To measure the parameters of the micro objects like watch gear, nanobots and so on.
o To visualize the fringes of the reflected light from the highly polished specimen
o To measure the roughness of a specimen.
UNIT-1: 13 Hours
Standards of measurement: Definition and Objectives of metrology, Standards of
length-International prototype meter, Imperial standard yard, Wave length standard, subdivision
of standards, line and end standard, calibration of end bars (Numerical), Slip gauges,
Wringing phenomena, Indian Standards (M-81, M-12), Numerical problems on building of
slip gauges.
System of Limits, Fits, Tolerance and Gauging: Definition of tolerance, Specification in

assembly, Principle of interchangeability and selective assembly limits of size, Indian standards,
concept of limits of size and tolerances, compound tolerances, accumulation of tolerances,

definition of fits, types of fits and their designation (IS919-1963), geometrical tolerance,
positional-tolerances, hole basis system, shaft basis system, classification of gauges, brief
concept of design of gauges (Taylor's principles), Wear allowance on gauges, Types of gauges-
plain plug gauge, ring gauge, snap gauge, limit gauge and gauge materials.
UNIT-2: 13 Hours
Comparators and Angular measurement: Introduction to comparators, characteristics,
classification of comparators, mechanical comparators-Johnson Mikrokator, sigma
comparators, dial indicator, optical comparators-principles, Zeiss ultra optimeter, electric and
electronic comparators-principles, LVDT, pneumatic comparators, back pressure gauges, solex
comparators. Angular measurements, bevel protractor, sine principle and use of sine bars, sine
centre, use of angle gauges (numericals on building of angles), clinometers.
Interferometer and screw thread, gear measurement: Interferometer, interferemetry,

autocollimator. Optical flats. Terminology of screw threads, measurementof major diameter,
minor diameter, pitch, angle and effective diameter of screw threadsby 2-wire and 3-wire
methods, best size wire. Tool maker's microscope, gear .to., terminology, use of gear
tooth vernier caliper and micrometer.
UNIT-3: 11 Hours
Measurements and measurement systems: Definition, significance of measurement,
generalized measurement system, definitions and concept of accuracy, precision, calibration,
threshold, sensitivity, hysterisis, repeatability, linearity, loading effect, system response-times
delay. Errors in measurement, classification of errors. Transducers, transfer efficiency,
primary and secondary transducers, electrical, mechanical, electronic transducers, advantages
of each type transducers.
Intermediate modifying and terminating devices: Mechanical systems, inherent problems,

electrical intermediate modifying devices, input circuitry, ballast circuit, electronic amplifiers
and telemetry. Terminating devices, mechanical, cathode ray oscilloscope, oscillographs, X-Y
plotters.

UNIT-4: 11 Hours
Measurement of force, torque and pressure: Principle, analytical balance,platform balance,
proving ring. Torque measurement, Prony brake, hydraulicdynamometer. Pressure
measurements, principle, use of elastic merijbers, Bridgemangauge, Mcloed gauge, Pirani
gauge.
UNIT-5: 11 hours
Temperature and strain measurement: Resistance thermometers, thermocouple, law of
thermo couple, materials used for construction, pyrometer, optical pyrometer. Strain
measurements, strain gauge, preparation and mounting of strain gauges, gauge factor, methods of
strain measurement.
ESSENTIAL READINGs:
1. Beckwith marangoni and Llienhard Mechanical measurements, pearson education,

6th ed., 2006.
2. R.K. jain Engineering metrology, , khanna publishers, 1994.
1. Engineering metrology, I.C. Gupta, dhapat rai publications,delhi.
2. R..K. jain Mechanical measurements,
3. Alsutko, Jerry. D. Faulk, Industrial instrumentation, Thompson asia pvt. ltd.2002.
4. Ernest O. Doblin Measurement systems applications and design, mcgraw

hill book co.

ME451 MECHANICAL MEASUREMENTS AND METROLOGY LABORATORY
PAPER DESCRIPTION: Provides the knowledge about the various measuring devices and
methods.
PAPER OBJECTIVE: To provide the working knowledge and importance of the metrology and
the measurement and about calibration and its importance.
Level of knowledge: Working.
of Measurements and Metrology.
LEARNING OUTCOME:
o Will be able to perform various calibrations, appreciate its application in various
engineering application.
o Will be able to perform various measurements for various mechanical elements.
o Will be able to carry out measurement tests.
Part-A: Mechanical measurements
1. Calibration of Pressure Gauge
2. Calibration of Thermocouple
3. Calibration of LVDT
4. Calibration of Load cell
5. Determination of modulus of elasticity of a mild steel specimen using strain gauges.
Part-B: Metrology
1. Measurements using Optical Projector / Toolmaker Microscope.
2. Measurement of angle using Sine Center / Sine bar / bevel protractor
3. Measurement of alignment using Autocollimator / Roller set
4. Measurement of cutting tool forces using
a. Lathe tool Dynamometer
b. Drill tool Dynamometer.

5. Measurement of Screw thread Parameters using Two wire or Three-wire method.

6. Measurements of Surface roughness, Using Tally Surf/Mechanical Comparator
7. Measurement of gear tooth profile using gear tooth vernier /Gear tooth micrometer
8. Calibration of Micrometer using slip gauges
9. Measurement using Optical Flats

ME452 MACHINE SHOP
PAPER DESCRIPTION: Provides working knowledge about machine tools.

PAPER OBJECTIVES:
o Under Standing of various types of machines and their mechanisms, manufacturing
processes of machine tool components.
o Performing experiments on the various machines gives the complete knowledge of the
machines to the learner. The machine tools lab ( Machine Shop) gives the industry
environment exposure to the students.
o The student feel the industry environment while doing the experiments and operations on
the specified machines.
o The students gain the master knowledge and skills when they complete the experiments at
the end of semester.
LEVEL OF KNOWLEDGE: Working.
LEARNING OUTCOME:
o Will be able to prepare various mechanical element , appreciate its application in
PART – A
Preparation of three models on lathe involving Plain turning, Taper turning, Step turning, Thread
cutting, Facing, Knurling, Drilling, Boring, Internal Thread cutting and Eccentric turning.
PART – B
Cutting of V Groove/ dovetail / Rectangular groove using a shaper.
Cutting of Gear Teeth using Milling Machine.

HE471 HOLISTIC EDUCATION

PAPER DESCRIPTION: This paper contains three units which are Personal skills, Inter-
personal Skills and Societal Skills.
PAPER OBJECTIVES:
o Holistic development of the individual adult in every student
o Knowing life and its principles
o Broadening the outlook to life
o Training to face the challenges of life
o Confidence creation and personality development
o Emotional control and stress management
o Creating awareness on duties, rights and obligations a s member of the Society
o Realizing Personal Freedom-its limits and limitations
o Developing the attitude to be a contributor and giver
o Realizing the real happiness in life

Personalskills 04Hours
Stress management
Scientific temper
Interpersonalskills 04Hours
Change management
Networking and PR skills
Societal skills 04Hours
Selected areas of the constitution
1. “Modules on Holistic development” (Prepared by Core committee, Christ College)
2. Bradley C. McRae, “Practical Time management”, International self-counsel Press Ltd.,
2001
3. Ronald. B., Adler &Jeanne M. Elmhorst, “Communicating at work–Principles and
practice for business and professions”, McGraw Hill

SEMESTER V
ME531 DESIGN OF MACHINE ELEMENTS-I
OBJECTIVES:
o This course “Design of Machine Elements -I” is designed with the following objectives :
o The student shall gain appreciation and understanding of the design function in
mechanical engineering, the steps involved in designing and the relation of design
activity with manufacturing activity.
o Shall be able to choose proper materials to different machine elements depending on
their physical and mechanical properties. Thus he shall be able to apply the knowledge of
material science in real life usage.
o Student shall gain a thorough understanding of the different types of failure modes and
criteria. He will be conversant with various failure theories and be able to judge which
criterion is to be applied in which situation.
o Student shall gain design knowledge of the different
o t types of elements used in the machine design process. Eg., fasteners, shafts, couplings
etc. and will be able to design these elements for each application
LEARNING OUTCOME:
o To describe the various design process.
o To explain the various problem solving strategies.
o To explain the embodiment design and detail design.
o To explain the parameters of failures.
o To explain the parameter design and tolerance design.
o Will acquire skill to do select proper material for specific application.
o Will be in a position to do design for industrial application.
o Will be able to do design of mechanical elements.
o Will have sufficient ability to optimize.
o Enhances the capabilities to assume suitable technical specifications.

UNIT- 1 12 Hours.
INTRODUCTION: Definitions: normal, shear, biaxial and tri axial stresses, Stress tensor,
Principal Stresses. Engineering Materials and their mechanical properties, Stress-Strain
diagrams, Stress Analysis, Design considerations: Codes and Standards.
DESIGN FOR STATIC & IMPACT STRENGTH:

Static Strength: Static loads and factor of safety, Theories of failure: Maximum normal
stress theory, Maximum shear stress theory, Maximum strain theory, Strain energy theory,
Distortion energy theory. Failure of brittle and ductile materials, Stress concentration,
Determination of Stress concentration factor.
UNIT – 2 12 Hours
Impact Strength: Introduction, Impact stresses due to axial, bending and torsional loads, effect
of inertia.
DESIGN FOR FATIGUE STRENGTH: Introduction- S-N Diagram, Low cycle fatigue,
High cycle fatigue, Endurance limit, Modifying factors: size effect, surface effect, Stress
concentration effects, Fluctuating stresses, Goodman and Soderberg relationship, stresses
due to combined loading, cumulative fatigue damage.
THREADED FASTENERS: Stresses in threaded fasteners, Effect of initial tension, Design of
threaded fasteners under static, dynamic and impact loads, Design of eccentrically loaded bolted
joints.
DESIGN OF SHAFTS: Torsion of shafts, design for strength and rigidity with steady loading,
ASME codes for power transmission shafting, shafts under fluctuating loads and combined
loads.
COTTER AND KNUCKLE JOINTS, KEYS AND COUPLINGS: Design of Cotter and
Knuckle joints, Keys: Types of keys, Design of keys, Couplings: Rigid and flexible couplings,
Flange coupling, Bush and Pin type coupling and Oldham‟s coupling.

Riveted and Welded Joints – Types, rivet materials, failures of riveted joints, Joint
Efficiency, Boiler Joints, Lozanze Joints, Riveted Brackets. Welded Joints – Types, Strength of
butt and fillet welds, eccentrically loaded welded joints.
Power Screws: Mechanics of power screw, Stresses in power screws, efficiency and self-
locking, Design of Power Screw, Design of Screw Jack: (Complete Design).
ESSENTIAL READINGS
1. Mechanical Engineering Design, Joseph E Shigley and Charles R. Mischke. McGraw

Hill International edition, 6th Edition 2009.
2. Design of Machine Elements, V.B. Bhandari, Tata McGraw Hill Publishing

Company Ltd., New Delhi, 2nd Edition 2007.
DESIGN DATA HANDBOOK
1. Design Data Hand Book, K. Lingaiah, McGraw Hill, 2nd Ed.
2. Data Hand Book, K. Mahadevan and Balaveera Reddy, CBS Publication
3. Design Data Hand Book, H.G. Patil, Shri Shashi Prakashan, Belgaum.
RECOMMENDED READING
1. Machine Design, Robert L. Norton, Pearson Education Asia, 2001.
2. Design of Machine Elements, M. F. Spotts, T. E. Shoup, L. E. Hornberger, S. R.

Jayram and C. V. Venkatesh, Pearson Education, 2006.
3. Machine Design, Hall, Holowenko, Laughlin (Schaum‟s Outlines series) Adapted

by S.K. Somani, Tata McGraw Hill Publishing Company Ltd., New Delhi, Special
Indian Edition, 2008.
4. Fundamentals of Machine Component Design, Robert C. Juvinall and Kurt M Marshek,

Wiley India Pvt. Ltd., New Delhi, 3rd Edition, 2007.

ME532 ENERGY ENGINEERING
UNIT–1 12 Hours.
STEAM POWER PLANT: Different Types of Fuels used for steam generation, Equipment for
burning coal in lump form, strokers, different types, Oil burners, Advantages and Disadvantages
of using pulverized fuel, Equipment for preparation and burning of pulverized coal, unit system
and bin system. Pulverized fuel furnaces, cyclone furnace, Coal and ash handling, Generation of
steam using forced circulation, high and supercritical pressures.
UNIT – 2 12 Hours
A BRIEF ACCOUNT OF BENSON, VELOX SCHMIDT STEAM GENERATORS.
Chimneys: Natural, forced, induced and balanced draft, Calculations and numericals involving
height of chimney to produce a given draft. Cooling towers and Ponds. Accessories for the
Steam generators such as Superheaters, Desuperheater, control of superheaters, Economizers, Air
pre-heaters and re-heaters.
DIESEL ENGINE POWER PLANT: Applications of Diesel Engines in Power field. Method
of starting Diesel engines. Auxiliaries like cooling and lubrication system, filters, centrifuges, Oil
heaters, intake and exhaust system, Layout of diesel power plant.
HYDRO-ELECTRIC PLANTS: Hydrographs, flow duration and mass curves, unit hydrograph
and numericals. Storage and pondage, pumped storage plants, low, medium and high head plants,
Penstock, water hammer, surge tanks, gates and valves. General layout of hydel power plants.
Nuclear Power Plant: Principles of release of nuclear energy; Fusion and fission reactions.
Nuclear fuels used in the reactors. Multiplication and thermal utilization factors. Elements of the
nuclear reactor; moderator, control rod, fuel rods, coolants. Brief description of reactors of the
following types-Pressurized water reactor, Boiling water reactor, Sodium graphite reactor, Fast
Breeder reactor, Homogeneous graphite reactor and gas cooled reactor, Radiation hazards,
Shieldings, Radio active waste disposal.

SOLAR ENERGY: Solar Extra terrestrial radiation and radiation at the earth surface, radiation-
measuring instruments, working principles of solar flat plate collectors, solar pond and
photovoltaic conversion (Numerical Examples).
WIND ENERGY: Properties of wind, availability of wind energy in India, wind velocity and
power from wind; major problems associated with wind power, wind machines; Types of wind
machines and their characteristics, horizontal and vertical axis wind mills, coefficient of
performance of a wind mill rotor (Numerical Examples).
TIDAL POWER: Tides and waves as energy suppliers and their mechanics; fundamental
characteristics of tidal power, harnessing tidal energy, limitations.
OCEAN THERMAL ENERGY CONVERSION: Principle of working, Rankine cycle,

problems associated with OTEC.
GEOTHERMAL ENERGY CONVERSION: Principle of working, types of geothermal

station with schematic diagram, problems associated with geothermal conversion, scope of
geothermal energy.
ENERGY FROM BIO MASS: Photosynthesis, photosynthetic oxygen production, energy

plantation.
BIO CHEMICAL ROUTE: Biogas production from organic wastes by anaerobic fermentation,
classification of bio gas plants, factors affecting bio gas generation.
THERMO CHEMICAL ROUTE: Thermo chemical conversion on bio mass, types of

gasifiers.

ESSENTIAL READINGS:
1. Power Plant Engineering, P. K. Nag Tata McGraw Hill 2nd edn 2001.
2. Power Plant Engineering, Domakundawar, Dhanpath Rai sons. 2003
1. Power Plant Engineering, R. K. Rajput, Laxmi publication, New Delhi.
2. Principles of Energy conversion, A. W. Culp Jr., McGraw Hill. 1996
3. Non conventional Energy sources, G D Rai Khanna Publishers.
4. Non conventional resources, B H Khan TMH - 2007

ME533 DYNAMICS OF MACHINES

OBJECTIVES:
Student will acquire knowledge of kinematic analyses of rigid body systems , concepts of planar,
inverse, Newtonian dynamic analyses of mechanisms and machines, concepts of three-
dimensional, inverse, Newtonian dynamic analyses of fixed-axis rotation of non-symmetric
bodies,concepts of static and dynamic mass balancing and flywheels, concepts of generalized
forces and the Principle of Virtual Work.
LEARNING OUTCOME:
o Understanding of the concepts of displacement, velocity and acceleration as vectors and
how to determine them.
o Understanding of the notion of a force as a vector.
o Ability to understand concepts of kinetic, potential and mechanical energies and the
concept of a conservative force.
o Ability to correctly draw the free-body diagram (FBD) for the system.
o Ability to conduct dynamic force analysis for various mechanisms.
o Ability to do analysis of frictions in different members like belt drives.
o Ability to do analysis for balancing of rotating masses and reciprocating masses.
o Ability to do governor mechanism classification and analyze the forces in the
mechanisms.
UNIT 1: 12 Hours.
Static Force Analysis: Introduction: Static equilibrium. Equilibrium of two and three force
members. Members with two forces and torque. Free body diagrams. Principle of virtual work.
Static force analysis of four bar mechanism and slider-crank mechanism with and without
friction.
UNIT 2: 12 Hours.
Dynamic Force Analysis: D'Alembert's principle, Inertia force, inertia torque. Dynamic force
analysis of four-bar mechanism and slider crank mechanism. Dynamically equivalent systems.
Turning moment diagrams and flywheels. Fluctuation of Energy. Determination of size of
flywheels.

UNIT 3: 12 Hours.
Friction and Belt Drives: Definitions: Types of friction: laws of friction, Friction in pivot and
collar bearings. Belt drives: Flat belt drives. ratio of belt tensions, centrifugal tension, power
transmitted.
Balancing of Rotating Masses: Static and dynamic balancing. Balancing of single rotating
mass by balancing masses in same plane and in different planes. Balancing of several rotating
masses by balancing masses in same plane and in different planes.
UNIT 4: 12 Hours.
Balancing of Reciprocating Masses: Inertia effect of crank and connecting rod, single cylinder
engine, balancing in multi cylinder-inline engine (primary & secondary forces), V-type engine;
Radial engine – Direct and reverse crank method.
Governors: Types of governors; force analysis of Porter and Hartnell governors. Controlling
force. stability, sensitiveness. Isochronism, effort and power .
UNIT 5: 12 Hours
.Gyroscope: Vectorial representation of angular motion. Gyroscopic couple. Effect of
gyroscopic couple on ship, plane disc, aeroplane, stability of two wheelers and four wheelers.
Analysis of Cams: Analysis of Tangent cam with roller follower and Circular arc cam operating
flat faced and roller followers. Undercutting in Cams
ESSENTIAL READINGS:
1 Theory of Machines, Sadhu Singh, Pearson Education. 2nd edition. 2007.

2 Theory of Machines, Rattan S.S. Tata McGraw Hill Publishing Company Ltd., New
Delhi, 3rd Edition, 2009.
1. “Theory of Machines & Mechanisms", J.J. Uicker, , G.R. Pennock, J.E. Shigley. OXFORD
3rd Ed. 2009
2. Mechanism and Machine Theory, A.G.Ambekar PHI, 2007

ME534 TURBO MACHINES

OBJECTIVES:
o To understand the basics of turbomachineryand to identify various types of
turbomachinery. To understand the major turbo machinery operations and its basics.
o To understand the 2D and 3D steady flow phenomena in turbomachine components
o Apply the Euler's equation for turbo machinery to analyze energy transfer in turbo
machines.
o To compute efficiencies of various turbo machines and to Analyze and select axial-
flow turbines and compressors.
o To understand and Analyze and select radial-flow turbo machines for various
industrial applications.
o To carry various Performance thermal cycle analysis on turbines.
UNIT -1 12 Hours.
Introduction: Definition of turbomachine, parts of turbomachines, Comparison with positive
displacement machines, Classification, Static and Stagnation states- Incompressible fluids and
perfect gases, Application of first and second law‟s of thermodynamics to turbomachines,
Efficiencies of turbomachines. Problems.
Energy exchange in Turbomachines: Euler‟s turbine equation, Alternate form of Euler‟s
turbine equation, Velocity triangles for different values of degree of reaction, Components of
energy transfer, Degree of Reaction, utilization factor, Relation between degree of reaction and
Utilization factor, Problems.
General Analysis of Turbomachines: Radial flow compressors and pumps – general analysis,
Expression for degree of reaction, velocity triangles, Effect of blade discharge angle on energy
transfer and degree of reaction, Effect of blade discharge angle on performance, Theoretical head
– capacity relationship, General analysis of axial flow pumps and compressors, degree of
reaction, velocity triangles, Problems.

Dimensionless analysis and thermodynamics of fluid flow: Dimensionless parameters and
their significance, Effect of Reynold‟s number, Unit and specific quantities, model studies.
Overall isentropic efficiency, stage efficiency (their comparison) and polytropic efficiency for
both compression and expansion processes. Reheat factor for expansion process.
Steam Turbines: Classification, Single stage impulse turbine, condition for maximum blade
efficiency, stage efficiency, Need and methods of compounding, Multi-stage impulse turbine,
expression for maximum utilization factor, Reaction turbine – Parsons‟s turbine, condition for
maximum utilization factor, reaction staging. Problems.
Hydraulic Turbines: Classification, Different efficiencies, Pelton turbine – velocity triangles,
design parameters, Maximum efficiency. Francis turbine - velocity triangles, design parameters,
runner shapes for different blade speeds. Draft tubes- Types and functions. Kaplan and Propeller
turbines - velocity triangles, design parameters. Problems.
Centrifugal Pumps: Classification and parts of centrifugal pump, different heads and
efficiencies of centrifugal pump, Minimum speed for starting the flow, Maximum suction lift,
Net positive suction head, Cavitation, Need for priming, Pumps in series and parallel. Problems.
Centrifugal Compressors: Stage velocity triangles, slip factor, power input factor, Stage work,
Pressure developed, stage efficiency and surging and problems.
Axial flow Compressors: Expression for pressure ratio developed in a stage, work done factor,
efficiencies and stalling. Problems.
(Note: Since dimensional analysis is covered in Fluid Mechanics subject, questions on
dimensional analysis may not be given for examinations. However, dimensional parameters and
model studies may be given more weightage.)

ESSENTIAL READINGS:
1. An Introduction to Energy Conversion, Volume III, Turbomachinery, V. Kadambi and

Manohar Prasad, New Age International Publishers, reprint 2008.
2. Turbines, Compressors & Fans, S. M. Yahya, Tata McGraw Hill Co. Ltd., 2 nd edition,
2002
1. Principals of Turbomachines, D. G. Shepherd, The Macmillan Company (1964).
2. Fluid Mechanics & Thermodynamics of Turbomachines, S. L. Dixon, Elsevier

(2005).
3. Turbomachine, B.K.Venkanna PHI, 2007

ME535 MANUFACTURING PROCESS III

OBJECTIVES:
o Develop understanding of basic and advanced manufacturing processes and

capabilities of each.
o Extend basis knowledge to solve manufacturing processes related problems.
o Develop an understanding of Concurrent Engineering and the importance to
manufacturing industries.
o Enhance ability to determine what is given and what to find.
o Learn to make engineering judgments.
o Learn the impact that modern manufacturing techniques have on human
advancement.
o Understand what manufacturing processes references are available.
o Discuss current manufacturing issues.
o Emphasize the problem solving process and application techniques.
LEARNING OUTCOME:
o Will be able to implement specific advanced and emerging manufacturing technologies
in modern industry.
etc.
INTRODUCTION AND CONCEPTS: Classification of metal working processes,
characteristics of wrought products, advantages and limitations of metal working
processes.Concepts of true stress, true strain, triaxial & biaxial stresses. Determination of flow
stress. Principal stresses, Tresca & Von-Mises yield criteria, concepts of plane stress & plane
strain.

EFFECTS OF PARAMETERS: Temperature, strain rate, friction and lubrication, hydrostatic

pressure in metalworking, Deformation zone geometry, workability of materials, Residual
stresses in wrought products.
FORGING: Classification of forging processes. Forging machines & equipment. Expressions
for forging pressures & load in open die forging and closed die forging by slab analysis, concepts
of friction hill and factors affecting it. Die-design parameters. Material flow lines in forging.
Forging defects, Residual stresses in forging. Simple problems.
ROLLING: Classification of Rolling processes. Types of rolling mills, expression for RoIling
load. Roll separating force. Frictional losses in bearing, power required in rolling, Effects of
front & back tensions, friction, friction hill. Maximum possible reduction. Defects in rolled
products. Rolling variables, simple problems.
DRAWING: Drawing equipment & dies, expression for drawing load by slab analysis, power
requirement. Redundant work and its estimation, optimal cone angle & dead zone formation,
drawing variables, Tube drawing, classification of tube drawing, simple problems.
EXTRUSION: Types of extrusion processes, extrusion equipment & dies, deformation,
lubrication & defects in extrusion. Extrusion dies, Extrusion of seamless tubes. Extrusion
variables, simple problem
SHEET & METAL FORMING: Forming methods, dies & punches, progressive die,
compound die, combination die. Rubber forming. Open back inclinable press (OBI press),
piercing, blanking, bending, deep drawing, LDR in drawing, Forming limit criterion, defects of
drawn products, stretch forming. Roll bending & contouring, Simple problems

HIGH ENERGY RATE FORMING METHODS: Principles, advantages and applications,
explosive forming, electro hydraulic forming, Electromagnetic forming.
POWDER METALLURGY: Basic steps in Powder metallurgy brief description of methods of
production of metal powders, conditioning and blending powders, compaction and sintering
application of powder metallurgy components, advantages and limitations.
ESSENTIAL READINGS:
1. Mechanical metallurgy (SI units), G.E. Dieter, Mc Graw Hill pub.2001
2. Manufacturing Process – III, Dr. K.Radhakrishna, Sapna Book House, 2009.
1. Materials and Processes in Manufacturing, E.paul, Degramo, J.T. Black, Ronald, A.K.
Prentice -hall of India 2002
2. Principles of Industrial metal working process, G.W. Rowe, CBSpub. 2002
3. Manufacturing Science, Amitabha Ghosh & A.K. Malik - East -Westpress 2001
4. Technology of Metal Forming Process, Surendra kumar, PHI – 2008

ME536 COMPUTER AIDED MACHINE DRAWING

OBJECTIVES:
o To visualize an object and convert it into a drawing.
o To gain knowledge of conventional representation of various machining and mechanical
details as per IS.
o To become conversant with 2-D and 3-D drafting.
o Gaining the knowledge of CAD software and its features for effective representation of
machine components and their assembly.
o Understand the format and Standards of Machine Drawing.
o Understand the technical information on machine drawings.
o Understanding and drawing of various views and machine components.
o Learning how to assemble and disassemble important parts used in major mechanical
engineering applications.
LEARNING OUTCOME
o Will be able to read and understand the machine drawings.
o Will be able to prepare machine components drawings.
o Will be able to do assembly drawings.
o Will be in a position to do drawings and assembly using computer.
INTRODUCTION:
Review of graphic interface of the software. Review of basic sketching commands and
navigational commands. Starting a new drawing sheet. Sheet sizes. Naming a drawing, Drawing
units, grid and snap.
PART-A
UNIT 1:
Sections of Solids: Sections of Pyramids, Prisms, Cubes, Tetrahedrons, Cones and Cylinders
resting only on their bases (No problems on, axis inclinations, spheres and hollow solids). True
shape of sections.

Orthographic Views: Conversion of pictorial views into orthographic projections. of simple

machine parts with or without section. (Bureau of Indian Standards conventions are to be
followed for the drawings) Hidden line conventions. Precedence of lines.
UNIT 2: 08 Hours
Thread Forms: Thread terminology, sectional views of threads. ISO Metric (Internal &
External) BSW (Internal & External) square and Acme. Sellers thread, American Standard
thread.
Fasteners: Hexagonal headed bolt and nut with washer (assembly), square headed bolt and nut
with washer (assembly) simple assembly using stud bolts with nut and lock nut. Flanged nut,
slotted nut, taper and split pin for locking, counter sunk head screw, grub screw, Allen screw.
PART-B
UNIT 3: 08 Hours
Keys & Joints :
Parallel key, Taper key, Feather key, Gibhead key and Woodruff key
Riveted Joints: Single and double riveted lap joints, butt joints with single/double cover straps
(Chain and Zigzag, using snap head rivets). cotter joint (socket and spigot), knuckle joint (pin
joint) for two rods.
UNIT 4: 08 Hours
Couplings:
Split Muff coupling, Protected type flanged coupling, pin (bush) type flexible coupling,
Oldham's coupling and universal coupling (Hooks' Joint)
PART - C
Assembly Drawings
(Part drawings should be given)
1. Plummer block (Pedestal Bearing)
2. Rams Bottom Safety Valve
3. I.C. Engine connecting rod
4. Screw jack (Bottle type)

5. Tailstock of lathe
6. Machine vice
7. Tool Head of a shaper
ESSENTIAL READINGS:
1. 'A Primer on Computer Aided Machine Drawing-2007‟, Published by VTU, Belgaum.

2. 'Machine Drawing', N.D.Bhat & V.M.Panchal
1. 'A Text Book of Computer Aided Machine Drawing', S. Trymbaka Murthy, CBS Publishers,
New Delhi, 2007
2. 'Machine Drawing‟, K.R. Gopala Krishna, Subhash Publication.
3. 'Machine Drawing with Auto CAD', Goutam Pohit & Goutham Ghosh, 1st Indian print
Pearson Education, 2005
4. 'Auto CAD 2006, for engineers and designers', Sham Tickoo. Dream tech 2005
5. 'Machine Drawing', N. Siddeshwar, P. Kanniah, V.V.S. Sastri, published by Tata Mc
GrawHill,2006

ME551 FLUID MECHANICS AND MACHINES LABORATORY
PAPER DESCRIPTION: Provides working knowledge of fluid mechanics and machines.

PAPER OBJECTIVE:
o To develop skills in the field of fluid mechanics and machines.
o Be in a position to relate theory and practice,
of fluid mechanics and machines.
LEARNING OUTCOME:
o Will be able to apply the concepts of fluid mechanics and machines, appreciate its
application in various engineering application.
o Will be able to perform various test of fluid mechanics and machines for various
mechanical properties.
o Will be able to carry out performance tests on fluid mechanics and machines.
PART - A
1. Determination of coefficient of friction of flow in a pipe.
2. Determination of minor losses in flow through pipes.
3. Determination of force developed by impact of jets on vanes.
4. Calibration of flow measuring Devices like
a) Orifice Plate Meter
b) Nozzle
c) Venturimeter
d) V-notch

PART - B
5. Performance testing of Turbines
3. Pelton wheel
4. Francis Turbine
5. Kaplan Turbines
6. Performance testing of Pumps
(vii) Single stage / Multi stage centrifugal pumps
(viii) Reciprocating pump
7. Performance test of a two stage Reciprocating Air Compressor
8. Performance test on an Air Blower

ME552 ENERGY CONVERSION ENGINEERING LABORATORY

PAPER DESCRIPTION: Provides working knowledge of energy conversion engineering.
PAPER OBJECTIVE:
o To develop skills in the field of energy conversion engineering.
This Laboratory has various experiments that aim at enabling the students to learn the concepts
of energy conversion engineering.
LEARNING OUTCOME:
o Will be able to apply the concepts of energy conversion engineering, appreciate its
o Will be able to perform various test of energy conversion engineering for various
o Will be able to carry out performance tests on energy conversion engineering.
PART - A
1. Determination of Flash point and Fire point of lubricating oil using Abel Pensky and
Martin (closed) / Cleavland (Open Cup) Apparatus.
2. Determination of Calorific value of solid, liquid and gaseous fuels.
3. Determination of Viscosity of a lubricating oil using Redwoods, Saybolts and Torsion
Viscometers.
4. Valve Timing/port opening diagram of an I.C. engine (4 stroke/2 stroke).
5. Use of planimeter

PART - B
1. Performance Tests on I.C. Engines, Calculations of IP, BP, Thermal efficiencies, SFC,
FP, heat balance sheet for
(a) Four stroke Diesel Engine
(b) Four stroke Petrol Engine
(c) Multi Cylinder Diesel/Petrol Engine, (Morse test)
(d) Two stroke Petrol Engine
(e) Variable Compression Ratio I.C. Engine.

SEMESTER VI
ME631 DESIGN OF MACHINE ELEMENTS – II
OBJECTIVES:
This course “Design of Machine Elements -II” is designed with the following objectives :
mechanical engineering, the steps involved in designing and the relation of design
activity with manufacturing activity.
o Shall be able to choose proper materials to different machine elements depending on
their physical and mechanical properties. Thus he shall be able to apply the knowledge of
o Student shall gain design knowledge of the differenttypes of elements used in the machine
design process. Eg., fasteners, shafts, couplings etc. and will be able to design these
elements for each application
LEARNING OUTCOME:

o Enhances the capabilities to assume suitable technical specifications.

UNIT - 1 13 Hours.
Curved Beams: Stresses in curved beams of standard cross sections used in crane hook,
punching presses & clamps, closed rings and links
Cylinders & Cylinder Heads: Review of Lame‟s Equations; compound cylinders,
stresses due to different types of fits, cylinder heads, flats.
Springs: Types of springs - stresses in Helical coil springs of circular and non-circular
cross sections. Tension and compression springs, springs under fluctuating loads, Leaf
Springs: Stresses in leaf springs. Equalized stresses, Energy stored in springs, Torsion,
Belleville and Rubber springs.
UNIT – 3 13 Hours
Spur & Helical Gears: Spur Gears: Definitions, stresses in gear tooth: Lewis equation and
form factor, Design for strength, Dynamic load and wear load. Helical Gears: Definitions,
formative number of teeth, Design based on strength, dynamic and wear loads.
Bevel and Worm Gears: Bevel Gears: Definitions, formative number of teeth, Design based
on strength, dynamic and wear loads. Worm Gears: Definitions, Design based on strength,
dynamic, wear loads and efficiency of worm gear drives.
Clutches & Brakes: Design of Clutches: Single plate, multi plate and cone clutches. Design of
Brakes: Block and Band brakes: Self locking of brakes: Heat generation in Brakes.
Lubrication and Bearings: Lubricants and their properties, Mechanisms of Lubrication
bearing modulus, coefficient of friction, minimum oil film thickness, Heat Generated, Heat
dissipated, Bearing Materials, Examples of journal bearing and thrust bearing design.
IC Engine Parts: Design of piston, connecting rod and crank shaft.

ESSENTIAL READINGS
1. Mechanical Engineering Design, Joseph E Shigley and Charles R. Mischke. McGraw

Hill International edition, 6th Edition 2003.
2. Design of Machine Elements, V. B Bhandari, Tata McGraw Hill Publishing Company

Ltd., New Delhi, 2nd Edition 2007
REFERNCE BOOKS
1. Machine Design, Robert L. Norton, Pearson Education Asia, 2001.
2. Design of Machine Elements, M. F. Spotts, T. E. Shoup, L. E. Hornberger, S. R.

Jayram and C. V. Venkatesh, Pearson Education, 2006.
3. Machine Design, Hall, Holowenko, Laughlin (Schaum‟s Outlines series) Adapted by

S.K. Somani, Tata McGraw Hill Publishing Company Ltd., New Delhi, Special Indian
Edition, 2008.
4. Machine Design, A CAD Approach: Andrew D DIMAROGONAS, John Wiley Sons, Inc, 2
DESIGN DATA HAND BOOK
1. Design Data Hand Book , K. Lingaiah, McGraw Hill, 2nd Ed.
2. Data Hand Book, K. Mahadevan and Balaveera Reddy, CBS Publication
3. Design Data Hand Book, H.G. Patil, Shri Shashi Prakashan, Belgaum.

ME632 HEAT AND MASS TRANSFER
OBJECTIVES:
o Students will understand the basic concepts of conduction, convection and radiation heat
transfer.
o Students will understand how to formulate and be able to solve one and two dimensional
conduction heat transfer problems. Solution techniques will include both closed form and
numerical methods. Convection effects will be included as boundary conditions.
o Students will understand the fundamentals of the relationship between fluid flow,
convection heat transfer and mass transfer.
o Students will apply empirical correlations for both forced and free convection to
determine values for the convection heat transfer coefficient. They will then calculate
heat transfer rates using the coefficients.
o Students will understand the basic concepts of radiation heat transfer to include both
black body radiation and gray body radiation.
o Students will be able to evaluate radiation view factors using tables and the view factor
relationships.
LEARNING OUTCOME:
o Students gain in depth knowledge in various modes of heat transfer equipping them to
apply this knowledge in real life engineering situations like design of IC engines, heat
exchangers, etc.
o Students obtain sound theoretical knowledge on heat conduction enabling them to design
energy efficient industrial systems.
o Students acquire adequate knowledge in heat transfer in convection and radiation modes
that will enable them to conceptualize, design and commission alternate energy systems.
o A sound knowledge in “Heat and Mass Transfer” coupled with the understanding of
Thermodynamics enables students in developing green technologies that are essential in
the future for sustainable development.

UNIT–1 11 Hours
INTRODUCTORY CONCEPTS AND DEFINITIONS: Modes of heat transfer: Basic laws
governing conduction, convection, and radiation heat transfer; Thermal conductivity; convective
heat transfer coefficient; radiation heat transfer; combined heat transfer mechanism. Boundry
conditions of 1st, 2nd and 3rd Kind
CONDUCTION: Derivation of general three dimensional conduction equation in Cartesian
coordinate, special cases, discussion on 3-D conduction in cylindrical and spherical coordinate
systems (No derivation). One dimensional conduction equations in rectangular, cylindrical and
spherical coordinates for plane and composite walls. Overall heat transfer coefficient. Thermal
contact resistance.
UNIT – 2 13 Hours
VARIABLE THERMAL CONDUCTIVITY: Derivation for heat flow and temperature
distribution in plane wall. Critical thickness of insulation without heat generation, Thermal
resistance concept & its importance. Heat transfer in extended surfaces of uniform cross-section
without heat generation, Long fin, short fin with insulated tip and without insulated tip and fin
connected between two heat sources. Fin efficiency and effectiveness. Numerical problems.
ONE-DIMENSIONAL TRANSIENT CONDUCTION: Conduction in solids with negligible
internal temperature gradient (Lumped system analysis), Use of Transient temperature charts
(Heisler‟s charts) for transient conduction in slab, long cylinder and sphere; use of transient
temperature charts for transient conduction in semi-infinite solids. Numerical Problems.
CONCEPTS AND BASIC RELATIONS IN BOUNDARY LAYERS: Flow over a body
velocity boundary layer; critical Reynolds number; general expressions for drag coefficient and
drag force; thermal boundary layer; general expression for local heat transfer coefficient;
Average heat transfer coefficient; Nusselt number. Flow inside a duct- velocity boundary layer,
hydrodynamic entrance length and hydro dynamically developed flow; flow through tubes
(internal flow discussion only). Numericals based on empirical relation given in data handbook.
FREE OR NATURAL CONVECTION: Application of dimensional analysis for free
convection- physical significance of Grashoff number; use of correlations of free convection in

vertical, horizontal and inclined flat plates, vertical and horizontal cylinders and spheres,
Numerical problems.
FORCED CONVECTIONS: Applications of dimensional analysis for forced convection.
Physical significance of Reynolds, Prandtl, Nusselt and Stanton numbers. Use of various
correlations for hydro dynamically and thermally developed flows inside a duct, use of
correlations for flow over a flat plate, over a cylinder and sphere. Numerical problems.
HEAT EXCHANGERS: Classification of heat exchangers; overall heat transfer coefficient,
fouling and fouling factor; LMTD, Effectiveness-NTU methods of analysis of heat exchangers.
Numerical problems.
RADIATION HEAT TRANSFER: Thermal radiation; definitions of various terms used in
radiation heat transfer; Stefan-Boltzman law, Kirchoff‟s law, Planck‟s law and Wein‟s
displacement law. Radiation heat exchange between two parallel infinite black surfaces, between
two parallel infinite gray surfaces; effect of radiation shield; intensity of radiation and solid
angle; Lambert‟s law; radiation heat exchange between two finite surfaces-configuration factor
or view factor. Numerical problems.
ESSENTIAL READINGS:
1. Heat & Mass transfer, Tirumaleshwar, Pearson education 2006
2. Heat transfer-A basic approach, Ozisik, Tata Mc Graw Hill 2002

1. Heat transfer, a practical approach, Yunus A- Cengel Tata Mc Graw Hill
2. Principles of heat transfer, Kreith Thomas Learning 2001
3. Fundamentals of heat and mass transfer, Frenk P. Incropera and David P. Dewitt, John
Wiley and son‟s.
4. Heat transfer, P.K. Nag, Tata Mc Graw Hill 2002.

ME633 FINITE ELEMENT METHODS

OBJECTIVES:
o To provide the student with some knowledge and analysis skills in applying basiclaws in
mechanics and integration by parts to develop element equation for a springelement and
steps used in solving the problem by finite element method. (A, B, C)
o To develop the student‟s skills in applying the basic matrix operation to form a
globalmatrix equation and enforce the concept of steps in obtaining solutions for a
trussstructures (A,B,C)
o To develop the student‟s skills in applying the Hermite interpolation functions tosolve
beam problems. (A,B,C)
o To provide the student with some knowledge and analysis skills in forming basicdata
required in a FEM computer program. (A,B,C)
o To develop the student‟s skills in applying the Gaussian quadrature in
computingintegration in FEM. (A, B, C)
o To provide the student with some knowledge in isoparametric transformation.(A,B,C)
LEARNING OUTCOME
o Know the behavior of the element under different loading condition.
o Able to model irregular bodies and also find the areas of it.
o To find approximate solution for differential equations.
o To minimize an error using FEA software and get faster solution.
UNIT-1 12 Hours.
Introduction: Equilibrium equations in elasticity subjected to body force, traction forces, and
stress-strain relations for plane stress and plane strains. General description of Finite Element
Method, Application and limitations. Types of elements based on geometry. Node numbering,
Half band width.
UNIT-2 12 Hours.
Basic Procedure: Euler - Lagrauge equation for bar, beam (cantilever / simply supported fixed)
Principle of virtual work, principle of minimum potential energy, Raleigh‟s Ritz method. Direct
approach for stiffness matrix formulation of bar element. Galerkin‟s method.

UNIT-3 12 Hours.
Interpolation Models: Interpolation polynomials- Linear, quadratic and cubic. Simplex complex
and multiplex elements. 2D PASCAL‟s triangle. CST elements-Shape functions and Nodal load
vector, Strain displacement matrix and Jacobian for triangular and rectangular element.
Solution of 1-D Bars: Solutions of bars and stepped bars for displacements, reactions and
stresses by using penalty approach and elimination approach. Guass-elimination technique.
UNIT-4 12 Hours.
Higher Order Elements: Langrange‟s interpolation, Higher order one dimensional elements-
Quadratic and cubic element and their shape functions. Shape function of 2-D quadrilateral
element-linear, quadric element Iso-parametric, Sub parametric and Super parametric elements.
numerical integration : 1, 2 and 3 gauge point for 1D and 2D cases.
Trusses: Stiffness matrix of Truss element. Numerical problems.
UNIT-5 12 Hours.
Beams: Hermite shape functions for beam element, Derivation of stiffness matrix. Numerical
problems of beams carrying concentrated, UDL and linearly varying loads.
Heat Transfer: Steady state heat transfer, 1D heat conduction governing equations. Functional
approach for heat conduction. Galerkin‟s approach for heat conduction. 1D heat transfer in thin
fins.
ESSENTIAL READING:
1 Finite Elements in Engineering, T.R.Chandrupatla, A.D Belegunde, 3rd Ed PHI.
2 Finite Element Method in Engineering, S.S. Rao, 4th Edition, Elsevier, 2006.
1.Finite Element Methods for Engineers U.S. Dixit, Cengage Learning, 2009
2.Concepts and applications of Finite Element Analysis, R.D. Cook D.S Maltus, M.E
Plesha, R.J.Witt, Wiley 4th Ed, 2009
3.Finite Element Methods, Daryl. L. Logon, Thomson Learning 3rd edition, 2001.
4.Finite Element Method, J.N.Reddy, McGraw -Hill International Edition.

ME634 MECHATRONICS & MICROPROCESSOR

OBJECTIVE:
o Implement Mechatronic solutions to a given specification.

o Produce software solutions for a modern microprocessor-based Mechatronic
system.
o Apply knowledge of control, sensors and actuators to control a Mechatronic
system.
o Demonstrate the competence in developing advanced microprocessor-based
Mechatronic products.
LEARNING OUTCOME:
o Will be in a position to understand and implement the control engineering
concepts in real life applications.
o Can effectively use the various electro mechanical sensors for building various
devices in real life applications.
o Can use the various soft various soft wares to simulate and understand the
functioning of mechatronic devices.
o Effective use of microprocessors in mechanical applications
Introduction to Mechatronic Systems: Measurement and control systems Their elements and
functions, Microprocessor based controllers.
Review of Transducers and Sensors: Definition and classification of transducers. Definition

and classification of sensors. Principle of working and applications of light sensors, proximity
sensors and Hall effect sensors.
UNIT 2 12 Hours.
Electrical Actuation Systems: Electrical systems, Mechanical switches, solid-state switches,
solenoids, DC & AC motors, Stepper motors and their merits and demerits. Signal
Conditioning: Introduction to signal conditioning. The operational amplifier, Protection,

Filtering, Wheatstone bridge, Digital signals Multiplexers, Data acquisition, Introduction to

Digital system. Processing Pulse-modulation.
Introduction to Microprocessors: Evolution of Microprocessor, Organization of
Microprocessors (Preliminary concepts), basic concepts of programming of microprocessors.
Review of concepts - Boolean algebra, Logic Gates and Gate Networks, Binary & Decimal
number systems, memory representation of positive and negative integers, maximum and
minimum integers. Conversion of real, numbers, floating point notation, representation of
floating point numbers, accuracy and range in floating point representation, overflow and
underflow, addition of floating point numbers, character representation.
Logic Function: Data word representation. Basic elements of control systems 808SA processor
architecture terminology such as CPU, memory and address, ALU, assembler data registers,
Fetch cycle, write cycle, state, bus, interrupts. Micro Controllers. Difference between
microprocessor and micro controllers. Requirements for control and their implementation in
microcontrollers. Classification of micro controllers.
UNIT – 5
Organization & Programming of Microprocessors: Introduction to organization of INTEL
808S-Data and Address buses, Instruction set of 8085, programming the 8085, assembly
language programming.
Central Processing Unit of Microprocessors: Introduction, timing and control unit basic
concepts, Instruction and data flow, system timing, examples of INTEL 8085 and INTEL 4004
register organization.

ESSENTIAL READING:
1. Mechatronics, W.Bolton, Longman, 2Ed, Pearson Publications, 2007.
2. Microprocessor Architecture, Programming And Applications With 8085/8085A, R.S.

Ganokar, Wiley Eastern.
1. Mechatronics and Microprocessors, K.P.Ramchandran, G.K.Vijayraghavan,

M.S.Balasundran, Wiley, 1st Ed, 2009
2. Mechatronics - Principles, Concepts and applications – Nitaigour and Premchand

Mahilik - Tata McGraw Hill- 2003.
3. Mechatronics Principles & applications, Godfrey C. Onwubolu, Elsevier. .
4. Introduction Mechatronics & Measurement systems, David.G. Aliciatore & Michael. B.

Bihistaned, Tata McGraw Hill, 2000.

ME636 HYDRAULICS AND PNEUMATICS
OBJECTIVES:
o Upon completion of this course students will demonstrate an understanding of Hydraulic

andPneumatic principles, equipment, Seals and industries.
o Students will be able to identify anddescribe the basic operation of Hydraulic /
Pneumatic systems, the various equipmentused in their operation, Hydraulic / Pneumatic
terms as well as actuator Sealing Devicedesign / material strengths and weaknesses.
o Students will be able to troubleshoot Hydraulic/Pneumatic equipment and Seals.
LEARNING OUTCOME:
o Will be in position to device various circuit for hydraulic and pneumatic applications.
o Will be in position to develop various hydraulic and pneumatic devices.
o To understand and illustrate the working of various types of pumps.
o To understand and illustrate the working of various hydraulic and pneumatic devices.
UNIT -1 12 Hours
Introduction to Hydraulic Power: Definition of hydraulic system, advantages, limitations,
applications, Pascal's law, structure of hydraulic control system, problems on Pascal's law.
The source of Hydraulic Power: Pumps Classification pumps, Pumping theory of positive
displacement pumps, construction and working of Gear pumps, Vane pumps, Piston pumps,
fixed and variable displacement pumps, Pump performance characteristics, pump Selection
factors, problems on pumps.
Hydraulic Actuators and Motors: Classification cylinder and hydraulic motors, Linear
Hydraulic Actuators [cylinders], single and double acting cylinder, Mechanics of Hydraulic
Cylinder Loading, mounting arrangements, cushioning, special types of cylinders, problems on
cylinders, construction and working of rotary actuators such as gear, vane, piston motors,
Hydraulic Motor Theoretical Torque, Power and Flow Rate, Hydraulic Motor Performance,
problems, symbolic representation of hydraulic actuators (cylinders and motors).

UNIT-2 12 Hours
Control Components in Hydraulic Systems: Classification of control valves, Directional

Control Valves- Symbolic representation, constructional features of poppet, sliding spool, rotary
type valves solenoid and pilot operated DCV, shuttle valve, check valves, Pressure control valves
- types, direct operated types and pilot operated types. Flow Control Valves - compensated and
non-compensated FCV, needle valve, temperature compensated, pressure compensated, pressure
and temperature compensated FCV, symbolic representation.
Hydraulic Circuit Design And Analysis: Control of Single and Double Acting Hydraulic
Cylinder, Regenerative circuit, Pump Unloading Circuit, Double Pump Hydraulic System,
Counter balance Valve Application, Hydraulic Cylinder Sequencing Circuits, Automatic cylinder
reciprocating system, Locked Cylinder using Pilot check Valve, Cylinder synchronizing circuit
using different methods, factors affecting synchronization, Hydraulic circuit for force
multiplication, Speed Control of Hydraulic Cylinder, Speed Control of Hydraulic Motors, Safety
circuit, Accumulators, types, construction and applications with circuits.
UNIT - 3 12 Hours
Maintenance of Hydraulic System: Hydraulic Oils - Desirable properties, general type of
Fluids, Sealing Devices, Reservoir System, Filters and Strainers, wear of Moving Parts due to
solid -particle Contamination, temperature control (heat exchangers), Pressure switches, trouble
shooting.
Introduction to Pneumatic Control: Definition of pneumatic system, advantages, limitations,
applications, Choice of working medium. Characteristic of compressed air. Structure of
Pneumatic control System, fluid conditioners and FRL unit.
Pneumatic Actuators: Linear cylinder - Types, Conventional type of cylinder- working, End
position cushioning, seals, mounting arrangements- Applications. Rod - Less cylinders types,
working, advantages, Rotary cylinders- types construction and application, symbols.

UNIT-4 12 Hours
Pneumatic Control Valves: DCV such as poppet, spool, suspended seat type slide valve,
pressure control valves, flow control valves, types and construction, use of memory valve, Quick
exhaust valve, time delay valve, shuttle valve, twin pressure valve, symbols. 3Hrs Simple
Pneumatic Control: Direct and indirect actuation pneumatic cylinders, speed control of cylinders
- supply air throttling and Exhaust air throttling and Exhaust air throttling.
Signal Processing Elements: Use of Logic gates - OR and AND gates in pneumatic
applications. Practical Examples involving the use of logic gates, Pressure dependant controls-
types - construction - practical applications, Time dependent controls principle. Construction,
practical applications.
UNIT- 5 12 Hours
Multi- Cylinder Application: Coordinated and sequential motion control, Motion and control
diagrams. Signal elimination methods, Cascading method- principle, Practical application
examples (up to two cylinders) using cascading method (using reversing valves).
Electro- Pneumatic Control: Principles - signal input and out put, pilot assisted solenoid
control of directional control valves, Use of relay and contactors. Control circuitry for simple
signal cylinder application.
Compressed Air: Production of compressed air- Compressors Preparation of compressed air-

Driers, Filters, Regulators, Lubricators, Distribution of compressed air Piping layout.

ESSENTIAL READINGS:
1. “Fluid Power with Applications”, Anthony Esposito, Sixth edition, Pearson Education, Inc,
2000.
2. 'Pneumatics and Hydraulics', Andrew Parr, Jaico Publilishing Co
1. 'Oil Hydraulic systems', Principles and Maintenance S. R. Majurr, Tata Mc Graw Hill
Publishing Company Ltd. - 2001
2. 'Industrial Hydraulics', Pippenger, Hicks" McGraw Hill, New York
3. 'Hydraulic & Pneumatic Power for Production', Harry L. Stewart
4. 'Pneumatic Systems', S. R. Majumdar, Tata Mc Graw Hill Publish 1995
5. Power Hydraulics' Michael J Pinches & John G Ashby, Prentice Hall

ME651 HEAT & MASS TRANSFER LABORATORY
PAPER DESCRIPTION: Provides working knowledge of heat & mass transfer engineering.
PAPER OBJECTIVE:
o To develop skills in the field of heat & mass transfer engineering.
o Verify the principles of the course,Application of the theory , Understanding of
fundamentals of the subject.
of heat & mass transfer engineering.
OUTCOME:
o Will be able to apply the concepts of heat & mass transfer engineering, appreciate its
o Will be able to perform various test of heat & mass transfer engineering for various
o Will be able to carry out performance tests on heat & mass transfer engineering.
PART - A
1. Determination of Thermal Conductivity of a Metal Rod.

2. Determination of Overall Heat Transfer Coefficient of a Composite wall.
3. Determination of Effectiveness on a Metallic fin.
4. Determination of Heat Transfer Coefficient in a free Convection on a vertical tube.

5. Determination of Heat Transfer Coefficient in a Forced Convention Flow through a Pipe.

6. Determination of Emissivity of a Surface.
21 Hours
PART - B
1. Determination of Stefan Boltzman Constant.
2. Determination of LMDT and Effectiveness in a Parallel Flow and Counter Flow Heat
Exchangers
3. Experiments on Boiling of Liquid and Condensation of Vapour
4. Performance Test on a Vapour Compression Refrigeration.
5. Performance Test on a Vapour Compression Air - Conditioner
6. Experiment on Transient Conduction Heat Transfer
21 Hours

ME652 COMPUTER AIDED MODELING AND ANALYSIS LABORATORY
PAPER DESCRIPTION: Provides working knowledge of computer aided modeling and

analysis.
PAPER OBJECTIVE:
o To develop skills in the field of computer aided modeling and analysis.
o Verify the principles of the course, Application of the theory, Understanding of
fundamentals of the subject.
o This Laboratory has various experiments that aims at enabling the students to learn the
concepts of computer aided modeling and analysis.
LEARNING OUTCOME:
o Will be able to apply the concepts of computer aided modeling and analysis engineering,
appreciate its application in various engineering application.
o Will be able to perform various computer modeling and analysis for various mechanical
elements.
o Will be able to carry out computer aided analysis.
PART - A
Study of a FEA package and modeling stress analysis of

1. Bars of constant cross section area, tapered cross section area and stepped bar
6 Hours
2. Trusses – (Minimum 2 exercises)
3Hours

3. Beams – Simply supported, cantilever, beams with UDL, beams with varying load etc
(Minimum 6 exercises)
12 Hours
PART - B
4. Stress analysis of a rectangular plate with a circular hole 3 Hours

5. Thermal Analysis – 1D & 2D problem with conduction and convection boundary
conditions(Minimum 4 exercises) 9 Hours
6. Dynamic Analysis
5. Fixed – fixed beam for natural frequency determination
6. Bar subjected to forcing function
7. Fixed – fixed beam subjected to forcing function
9 Hours
1. A first course in the Finite element method, Daryl L Logan, Thomason, Third Edition
2. Fundaments of FEM, Hutton – McGraw Hill, 2004
3. Finite Element Analysis, George R. Buchanan, Schaum SerSEMESTER VII

SEMESTER VII
ME731 ENGINEERING ECONOMY
OBJECTIVES:
o PREPARE ENGINEERING STUDENTS TO ANALYZE COST/REVENUE DATA ANDCARRY OUT MAKE
ECONOMIC ANALYSES IN THE DECISION MAKINGPROCESS TO JUSTIFIY OR REJECT
ALTERNATIVES/PROJECTS ON ANECONOMIC BASIS.
o BE ABLE TO PERFORM AND EVALUATE PRESENT WORTH, FUTURE WORTH ANDANNUAL WORTH
ANALYSES ON ONE OF MORE ECONOMIC ALTERNATIVES.
o BE ABLE TO PERFORM AND EVALUATE PAYBACK PERIOD AND CAPITALIZEDCOST ON ONE OR
MORE ECONOMIC ALTERNATIVES.
o BE ABLE TO CARRY OUT AND EVALUATE BENEFIT/COST, LIFE CYCLE AND BREAK EVEN ANALYSES
ON ONE OR MORE ECONOMIC ALTERNATIVES.
LEARNING OUTCOME:
o Student will be competent to do budget, balance sheet, strategy for industrial needs.
o Acquire knowledge to evaluate and explain financial planning.
o Will learn strategies to evaluate strategies for running the industry in profit despite
adverse financial market
o Will be in a position to Carry out work strategy, analyse balance sheet and profit and
loss accounts.
UNIT – 1 13 Hours
INTRODUCTION: Engineering Decision-Makers, Engineering and Economics, Problem
solving and Decision making, Intuition and Analysis, Tactics and Strategy. Engineering
Economic Decision, Maze. Law of demand and supply, Law of returns, Interest and Interest
factors: Interest rate, Simple interest, Compound interest, Cash - flow diagrams, Personal loans
and EMI Payment, Exercises and Discussion.

PRESENT-WORTH COMPARISONS: Conditions for present worth comparisons, Basic

Present worth comparisons, Present-worth equivalence, Net Present-worth, Assets with unequal
lives, infinite lives, Future-worth comparison, Pay-back comparison, Exercises, Discussions and
problems.
UNIT – 2 13 Hours
EQUIVALENT ANNUAL-WORTH COMPARISONS: Equivalent Annual-Worth
Comparison methods, Situations for Equivalent Annual-Worth Comparisons, Consideration of
asset life, Comparison of assets with equal and unequal lives, Use of shrinking fund method,
Annuity contract for guaranteed income, Exercises, Problems.
RATE-OF-RETURN CALCULATIONS AND DEPRECIATION: Rate of return, Minimum

acceptable rate of return, IRR, IRR misconceptions, Cost of capital concepts. Causes of
Depreciation, Basic methods of computing depreciation charges, Tax concepts, corporate income
tax.
UNIT – 3 11 Hours
Estimating and Costing: Components of costs such as Direct Material Costs, Direct Labor
Costs, Fixed Over-Heads, Factory cost, Administrative Over-Heads, First cost, Marginal cost,
Selling price, Estimation for simple components.
UNIT – 4 ` 11 Hours
INTRODUCTION, SCOPE OF FINANCE, FINANCE FUNCTIONS: Statements of
Financial Information: Introduction, Source of financial information, Financial statements,
Balance sheet, Profit and Loss account, relation between Balance sheet and Profit and Loss
account. Simple Numericals
UNIT -5 12 Hours
FINANCIAL RATIO ANALYSIS: Introduction, Nature of ratio analysis, Liquidity ratios,
Leverage ratios, Activity ratios, Profitability ratios, Evaluation of a firm's earning power.
Comparative statements analysis. Simple numericals

FINANCIAL AND PROFIT PLANNING: Introduction, Financial planning, Profit planning,

Objectives of profit planning, Essentials of profit planning, Budget administration, type of
budgets, preparation of budgets, advantages, problems and dangers of budgeting. Introduction to
Bench Marking of Manufacturing Operation.
ESSENTIAL READINGS:
1. Engineering Economy, Riggs J.L., , McGraw Hill, 2002
2. Engineering Economy, Thuesen H.G. PHI , 2002
1. Engineering Economy, Tarachand, 2000.
2. Industrial Engineering and Management, OP Khanna, Dhanpat Rai & Sons. 2000
3. Financial Mangement, Prasanna Chandra, TMH, 2004
4. Finacial Management, IM PANDEY, Vikas Publisahing House, 2002

ME732 MECHANICAL VIBRATIONS
UNIT - 1 13 Hours
Introduction: Types of vibrations, Definitions, Simple Harmonic Motion (S.H.M.), Work done
by harmonic force, Principle of super position applied to SHM, Beats, Fourier theorem and
problems.
Undamped (Single Degree of Freedom) Free Vibrations: Derivations for spring mass systems,
Methods of Analysis, Natural frequencies of simple systems, Springs in series and parallel,
Torsional and transverse vibrations, Effect of mass of spring and Problems.
UNIT - 2 13 Hours
Damped free vibrations (1DOF): Types of damping, Analysis with viscous damping -
Derivations for over, critical and under damped systems, Logarithmic decrement and Problems.
Forced Vibrations (1DOF): Introduction, Analysis of forced vibration with constant harmonic
excitation - magnification factor, rotating and reciprocating unbalances, excitation of support
(relative and absolute amplitudes), force and motion transmissibility, Energy dissipated due to
damping and Problems.
UNIT -3 11 Hours
Vibration Measuring Instruments and Whirling of shafts: Seismic Instruments –
Vibrometers, Accelerometer, Frequency measuring instruments and Problems. Whirling of shafts
with and without damping, discussion of speeds above and below critical speeds and Problems.
Systems with two degrees of Freedom: Principle modes of vibrations, Normal mode and
natural frequencies of systems (without damping) – Simple spring mass systems, masses on
tightly stretched strings, double pendulum, torsional systems, combined rectilinear and angular
systems, geared systems and Problems. Undamped dynamic vibration absorber and Problems.

UNIT – 4 13 Hours
Numerical Methods for multi degree freedom of systems: Introduction, Maxwell‟s reciprocal
theorem, Influence coefficients, Rayleigh‟s method, Dunkerley‟s method, Stodola method,
Holzer‟s method, Orthogonality of principal modes, method of matrix iteration and Problems.
UNIT-5 11 Hours
Modal analysis and Condition Monitoring: Signal analysis, dynamic testing of machines and
structures, Experimental modal analysis, Machine condition monitoring and diagnosis.
ESSENTIAL READING:
1. Mechanical Vibrations, S. S. Rao, Pearson Education Inc, 4th edition, 2003.
2. Mechanical Vibrations, V. P. Singh, Dhanpat Rai & Company, 3rd edition, 2006.
1. Theory of Vibration with Applications, W. T. Thomson, M. D. Dahleh and C.

Padmanabhan, Pearson Education Inc, 5th edition, 2008.
2. Mechanical Vibrations: S. Graham Kelly, Schaum‟s outline Series, Tata McGraw Hill,
Special Indian Edition, 2007.
3. Theory and Practice of Mechanical Vibrations: J. S. Rao & K. Gupta, New Age
International Publications, New Delhi, 2001.
4. Mechanical Vibrations, G. K.Grover, Nem Chand and Bros, 6th edition, 1996.

ME733 OPERATIONS RESEARCH
OBJECTIVES:
o One or more advanced courses on applications in: supply chain and manufacturing
systems; data analysis; information engineering; financial engineering; or service
systems.
o A collaborative systems design experience.
o Collaborative project experiences involving both written and oral presentations.
o Courses with significant experiential learning components.
o Experiences with identifying, accessing, evaluating, and interpreting information and
data in support of assignments, projects, or research.
o Course experiences with large-scale datasets.
LEARNING OUTCOME:
Upon completion of the subject, students will be able to
o Identify and develop operational research models from the verbal description of the
real system.
o Recognize the importance and value of Operations Research and mathematical
modelling in solving practical problems in industry.
o Formulate a managerial decision problem into a mathematical model.
o Understand Operations Research models and apply them to real-life problems;
o Use computer tools to solve a mathematical model for a practical problem.
o Develop a report that describes the model and the solving technique, analyse the
results and propose recommendations in language understandable to the decision-
making processes in Management Engineering
o Proficiency with tools from optimization, probability, statistics, simulation, and
engineering economic analysis, including fundamental applications of those tools in
industry and the public sector in contexts involving uncertainty and scarce or
expensive resources.

o Facility with mathematical and computational modeling of real decision-making

problems, including the use of modeling tools and computational tools, as well as
analytic skills to evaluate the problems.
o Facility with the design, implementation, and analysis of computational experiments.
UNIT -1 12 Hours
INTRODUCTION: Evolution of OR, definition of OR, scope of OR, application areas of OR,
steps (phases) in OR study, characteristics and limitations of OR, models used in OR, linear
programming (LP) problem-formulation and solution by graphical method.
SOLUTION OF Linear Programming PROBLEMS: The simplex method-canonical and
standard form of an LP problem, slack, surplus and artificial variables, big M method and
concept of duality, dual simplex method.
UNIT -2 12 Hours
TRANSPORTATION PROBLEM: Formulation of transportation problem, types, initial basic

feasible solution using different methods, optimal solution by MODI method, degeneracy in
transportation problems, application of transportation problem concept for maximization cases.
Assignment Problem-formulation, types, application to maximization cases and travelling
salesman problem.
UNIT -3 12 Hours
PERT-CPM TECHNIQUES: Introduction, network construction - rules, Fulkerson‟s rule for

numbering the events, AON and AOA diagrams; Critical path method to find the expected
completion time of a project, floats; PERT for finding expected duration of an activity and
project, determining the probability of completing a project, predicting the completion time of
project; crashing of simple projects.
UNIT-4
11HOURSHOURQUEUING THEORY: Queuing systems and their characteristics, Pure-birth

and Pure-death models (only equations), empirical queuing models – M/M/1 and M/M/C models
and their steady state performance analysis.
UNIT -5 13 Hours
GAME THEORY: Formulation of games, types, solution of games with saddle point, graphical
method of solving mixed strategy games, dominance rule for solving mixed strategy games.
SEQUENCING: Basic assumptions, sequencing „n‟ jobs on single machine using priority rules,
sequencing using Johnson‟s rule-„n‟ jobs on 2 machines, „n‟ jobs on 3 machines, „n‟ jobs on „m‟
machines. Sequencing 2 jobs on „m‟ machines using graphical method.
ESSENTIAL READINGS
1. Operations Research, P K Gupta and D S Hira, Chand Publications, New Delhi - 2007
2. Operations Research, Taha H A, Pearson Education
REFERNCE BOOKS
1. Operations Research, A P Verma, S K Kataria &Sons, 2008
2. Operations Research, Paneerselvan, PHI
3. Operations Research, A M Natarajan, P Balasubramani, Pearson Education, 2005
4. Introduction to Operations Research, Hiller and Liberman, McGraw Hill
5. Operations Research S.D. Sharma, Ledarnath Ramanath & Co, 2002

ME734 INDUSTRIAL ROBOTICS

OBJECTIVES:
o To give an overview of the components, sensing elements used programming
techniques and applications of robots.
o Identify the characteristics of a variety of types and sizes of robots.
o Describe how artificial intelligence is applied to robotic systems When? How?
o Identify, sketch and label all major parts of an industrial robot.
o Describe the basic components that allow an operator to program robots.
o Compare and contrast robotic applications in medicine, industrial, and
entertainment applications.
o Set up and program an interactive robotics station
o Identify and describe the preparation and requirements for careers related to
robotics.
LEARNING OUTCOME:
o The study includes mathematical formulation for a robot body.
o Know the movement of robot arm based on there translation or rotational
moment.
o Selection of particular sensors for different robot application.
o Designing a robot with widest range of applications for current and future
products with minimum cost using suitable actuators, sensors etc.
UNIT – 1
Introduction and Mathematical Representation of Robots: History of Robots, Types of

Robots, Notation, Position and Orientation of a Rigid Body, Some Properties of Rotation
Matrices, Successive Rotations, Euler Angles For fixed frames X- Y -Z and moving frame ZYZ.
Transformation between coordinate system, Homogeneous coordinates, Properties of A/BT,
Types of Joints: Rotary, Prismatic joint, Cylindrical joint, Spherical joint, Representation of
Links using Denvit - Hartenberg Parameters: Link parameters for intermediate, first and last
links, Link transformation matrices, Transformation matrices of 3R manipulator, PUMA560
manipulator, SCARA manipulator

UNIT - 2
Kinematics of Serial Manipulators: Direct kinematics of 2R, 3R, RRP, RPR manipulator,
puma560 manipulator, SCARA manipulator, Stanford arm, Inverse kinematics of 2R, 3R
manipulator, puma560 manipulator.
Velocity and Static‟s of Manipulators: Differential relationships, Jacobian, Differential

motions of a frame (translation and rotation), Linear and angular velocity of a rigid body, Linear
and angular velocities of links in serial manipulators, 2R, 3R manipulators, Jacobian of serial
manipulator, Velocity ellipse of 2R manipulator, Singularities of 2R manipulators, Statics of
serial manipulators, Static force and torque analysis of 3R manipulator, Singularity in force
domain.
UNIT - 3
Dynamics of Manipulators: Kinetic energy, Potential energy, Equation of motion using

Lagrangian, Equation of motions of one and two degree freedom spring mass damper systems
using Lagrangian formulation, Inertia of a link, Recursive formulation of Dynamics using
Newton Euler equation, Equation of motion of 2R manipulator using Lagrangian Newton-Euler
formulation.
UNIT - 4
Trajectory Planning: Joint space schemes, cubic trajectory, Joint space schemes with via
points, Cubic trajectory with a via point, Third order polynomial trajectory planning, Linear
segments with parabolic blends, Cartesian space schemes, Cartesian straight line and circular
motion planning
Sensors: Sensor characteristics, Position sensors- potentiometers, Encoders, LVDT, Resolvers,

Displacement sensor, Velocity sensor-encoders, tachometers, Acceleration sensors, Force and
Pressure sensors piezoelectric, force sensing resistor, Torque sensors, Touch and tactile sensor,
Proximity sensors-magnetic, optical, ultrasonic, inductive, capacitive, eddy-current proximity
sensors.

UNIT - 5
Control: Feedback control of a single link manipulator- first order, second order system, PID
control, PID control of multi link manipulator, Force control of manipulator, force control of
single mass, Partitioning a task for force and position control- lever, peg in hole Hybrid force and
position controller.
Actuators: Types, Characteristics of actuating system: weight, power-to-weight ratio, operating

pressure, stiffness vs. compliance, Use of reduction gears, comparision of hydraulic, electric,
pneumatic actuators, Hydraulic actuators, proportional feedback control, Electric motors: DC
motors, Reversible AC motors, Brushles DC motors, Stepper motors- structure and principle of
operation, stepper motor speed-torque characteristics
ESSENTIAL READINGS:
1. Fundamental Concepts and Analysis, Ghosal A., Robotics, Oxford,2006
2. Introduction to Robotics Analysis, Systems, Applications, Niku, S. B., Pearso Education,

2008
1. Introduction to Robotics: Mechanica and Control, Craig, J. J., 2nd :J?:dition, Addison-
Welsey, 1989.
2. Fundamentals of Robotics, Analysis and Control, Schilling R. J., PHI, 2006

ME751 DESIGN LABORATORY

PAPER DESCRIPTION: Provides working knowledge of design Engineering.
PAPER OBJECTIVE:
o To develop skills in the field of design Engineering.
fundamentals of the subject design Engineering.
of design Engineering.
LEARNING OUTCOME:
o Will be able to apply the concepts of design Engineering, appreciate its application in
o Will be able to perform design engineering experiments for various mechanical elements.
PART - A
1. Determination of natural frequency, logarithmic decrement, damping ratio and damping
coefficient in a single degree of freedom vibrating systems (longitudinal and torsional)
2. Balancing of rotating masses.
3. Determination of critical speed of a rotating shaft.
4. Determination of Fringe constant of Photoelastic material using.
a. Circular disc subjected to diametral compression.
b. Pure bending specimen (four point bending )
5. Determination of stress concentration using Photoelasticity for simple components like plate
with a hole under tension or bending, circular disk with circular hole under compression, 2D
Crane hook.

PART - B
6. Determination of equilibrium speed, sensitiveness, power and effort of Porter/Prowel
/Hartnel Governor. (only one or more)
7. Determination of Pressure distribution in Journal bearing.
8. Determination of Principal Stresses and strains in a member subjected to combined loading
using Strain rosettes.
9. Determination of stresses in Curved beam using strain gauge.
10. Experiments on Gyroscope (Demonstration only)

ME752 CIM & AUTOMATION LABORATORY

PAPER DESCRIPTION: Provides working knowledge of CIM & automation.
PAPER OBJECTIVE:
o To develop skills in the field of cim & automation Engineering.
fundamentals of the subject cim & automation Engineering.
of cim & automation Engineering.
LEARNING OUTCOME:
 Will be able to apply the concepts of cim & automation Engineering, appreciate its
 Will be able to perform cim & automation Engineering experiments for various
mechanical elements.
 To develop scientific, technical and experimental skills to the students.
 To correlate the theoretical principles with application based studies.
PART - A
CNC part programming using CAM packages. Simulation of Turning, Drilling, Milling
operations. 3 typical simulations to be carried out using simulation packages like Master- CAM,
or any equivalent software.
PART - B
(Only for Demo/Viva voce)
1. FMS (Flexible Manufacturing System): Programming of Automatic storage and Retrieval
system (ASRS) and linear shuttle conveyor Interfacing CNC lathe, milling with loading
unloading arm and ASRS to be carried out on simple components.
2. Robot programming: Using Teach Pendent & Offline programming to perform pick and place,
stacking of objects, 2 programs.
PART - C
(Only for Demo/Viva voce)
Pneumatics and Hydraulics, Electro-Pneumatics: 3 typical experiments on Basics of these topics
to be conducted.

SEMESTER VIII
ME831 OPERATIONS MANAGEMENT
OBJECTIVES:
o Describe what the operations function is and why it is critical to an organization‟s
survival.
o Describe what a supply chain is and how it relates to a particular organization‟s
operations function.
o Discuss what is meant by operations management and supply chain management.
o Identify some of the major operations and supply chain activities, as well as career
opportunities in these areas.
o Make a case for studying both operations management and supply chain management.
LEARNING OUTCOME:
At the end of the course students will be able to:
o Understand the role of operations management in organizations.

o Differentiate between strategic and tactical operations decisions.
o Describe the key operations management decisions faced by managers.
o Understand three of the most important operations management practices: Total Quality
Management, Supply Chain Management, and Just-in-Time/Lean Operations.
UNIT 1 12 Hours
Production and Operations Management: Introduction, Functions within business
organizations, the operation management function, Classification of production systems,
Productivity, factors affecting productivity, contemporary issues and development
Decision Making: The decision process, characteristics of operations decisions, use of models,
decision making environments, graphical linear programming, analysis and trade-offs.
UNIT 2 13 Hours
Forecasting: Steps in forecasting process, approaches to forecasting, forecasts based on
judgment and opinion, analysis of time series data, accuracy and control of forecasts, choosing a

forecasting technique, elements of a good forecast,

Capacity & Location Planning: Importance of capacity decisions, defining and measuring
capacity, determinants of effective capacity, determining capacity requirement, developing
capacity alternatives, evaluating alternatives, Need for location decisions, nature of locations
decisions, general procedure for making locations decisions, evaluating locations decisions,
facilities layout – need for layout decisions, types of processing.
UNIT 3 11 Hours
Aggregate Planning & Master Scheduling: Aggregate planning – Nature and scope of
aggregate planning, strategies of aggregate planning, techniques for aggregate planning –
graphical and charting techniques, mathematical techniques. The master production schedule,
Master scheduling process, Master scheduling methods.
UNIT 4 12 Hours
Inventory Management: Types of Inventories, independent and dependent demand, reasons for
holding inventory, objectives of inventory control, requirements for effective inventory
management – information, cost, priority system. Inventory control and economic-order-quantity
models.
UNIT 5 12 Hours
Material Requirement Planning (MRP): Dependent versus independent demand, an overview
of MRP – MRP inputs and outputs, MRP processing, An overview of MRP-II and ERP capacity
requirement planning, benefits and limitations of MRP.
Purchasing and Supply Chain Management (SCM): Introduction, Importance of purchasing

and SCM, The procurement process, Concept of tenders, Approaches to SCM, Vendor
development, Measures of purchasing and SCM, Make or buy decision, Types of buying, E-
procurement.

ESSENTIAL READING:
1 Production and Operations Management, William J Stevenson, Tata McGraw Hill, 8th
Edition.
2 Operations Management-Theory and Practice, B Mahadevan, Pearson Education, 2007.
1. Production and Operations Management, Norman Gaither & Greg Frazier,
2. Operations Management for Competitive Advantage, R.B.Chase, N.J.Aquilino, F.

Roberts Jacob; McGraw Hill Companies Inc., Ninth Edition.
3. Production & Operations Management, Everett E.Adams, Ronald J.Ebert, Prentice Hall
of India Publications, Fourth Edition.
4. Production / Operations Management, Joseph G Monks, McGraw Hill Books

ME832 CONTROL ENGINEERING
OBJECTIVES:
o A control system consisting of interconnected components is designed to achieve a
desired purpose. To understand the purpose of a control system, it is useful to examine
examples of control systems through the course of history. These early systems
incorporated many of the same ideas of feedback that are in use today.
o Modern control engineering practice includes the use of control design strategies for
improving manufacturing processes, the efficiency of energy use, advanced automobile
control, including rapid transit, among others.
o We also discuss the notion of a design gap. The gap exists between the complex physical
system under investigation and the model used in the control system synthesis.
o The iterative nature of design allows us to handle the design gap effectively while
accomplishing necessary trade-offs in complexity, performance, and cost in order to
meet the design specifications.
UNIT – 1 13 Hours
Introduction: Concept of automatic controls, Open loop and closed loop systems, Concepts of
feedback, requirements of an ideal control system, Types of controllers- Proportional, Integral
Proportional Integral, Proportional Integral Differential controllers. Mathematical Models:
Transfer function models, models of mechanical systems, models of electrical circuits, DC and
AC motors in control systems, models of thermal systems, models of hydraulic systems,
pneumatic system, Analogous systems: Force voltage, Force current.
UNIT – 2 13 Hours
Block Diagrams and Signal Flow Graphs: Transfer Functions definition, function, block
representation of systems elements, reduction of block diagrams, Signal flow graphs: Mason‟s
gain formula.

Transient and Steady State Response Analysis: Introduction, first order and second order
system response to step, ramp and impulse inputs, concepts of time constant and its importance
in speed of response. System stability: Routh‟s-Hurwitz Criterion.
UNIT – 3 11 Hours
Frequency Response Analysis: Polar plots, Nyquist stability criterion, Stability analysis,
Relative stability concepts, Gain margin and phase margin, M&N circles. Frequency Response
Analysis Using Bode Plots: Bode attenuation diagrams, Stability analysis using Bode plots,
Simplified Bode Diagrams.
UNIT – 4 12 Hours
Root Locus Plots: Definition of root loci, General rules for constructing root loci, Analysis
using root locus plots.
UNIT- 5 11 Hours
System Compensation and State Variable Characteristics of Linear Systems: Series and
feedback compensation, Introduction to state concepts, state equation of linear continuous data
system. Matrix representation of state equations, controllability and observability, Kalman and
Gilberts test.
ESSENTIAL READING :
1. Modern Control Engineering, Katsuhiko Ogatta, Pearson Education,2004.
2. Control Systems Principles and Design, M.Gopal, TMH,2000.
1. Modern Control Systems, Richard.C.Dorf and Robert.H.Bishop, Addison Wesley,1999
2. System dynamics & control, Eronini-Umez, Thomson Asia pte Ltd. singapore, 2002.
3. Feedback Control System, Schaum‟s series. 2001.

ELECTIVE-I (ME635)
ME635 THEORY OF ELASTICITY
OBJECTIVES:
o Be able to analyze some real problem and to formulate the conditions of
theory of elasticity application
o Be able to execute a reasonable choice of parameters of the model (geometry,
material properties, boundary conditions)
o Be able to analyze the result of solution by standard computational programs.
LEARNING OUTCOMES:
o To be able to execute the stress state and stresses analysis Topic of Work: The
stresses state analysis.
o To be able to solve a problem of strain analysis Topic of Work: The strain
state analysis.
o To be able to use the numerical methods for the problem of the theory of
elasticity in practice.
o To be able to use theory for solution of practice problem of stress and strain
analysis Final examination.
UNIT – 1 13 Hours
DEFINITION AND NOTATION: Stress, Stress at a Point, Equilibrium Equations, Principal

Stresses, Mohr‟s Diagram, Maximum Shear Stress, Boundary Conditions.
STRAIN AT A POINT: Compatibility Equations, Principal Strains, Generalised Hooke‟s law,
Methods of Solution of Elasticity Problems – Plane Stress-Plane Strain Problems.
UNIT – 2 11 Hours
TWO DIMENSIONAL PROBLEMS: Cartesian co-ordinates – Airy‟s stress functions –
Investigation of Airy‟s Stress function for simple beam problems – Bending of a narrow
cantilever beam of rectangular cross section under edge load – method of Fourier analysis – pin
ended beam under uniform pressure.

UNIT – 3 13 Hours
GENERAL EQUATIONS IN CYLINDRICAL CO-ORDINATES: Thick cylinder under
uniform internal and / or external pressure, shrink and force fit, stress concentration.
STRESSES IN AN INFINITE PLATE (with a circular hole) subjected to uniaxial and biaxial
loads, stress concentration, stresses in rotating discs and cylinders.
UNIT – 4 11 Hours
TORSION OF CIRCULAR, ELLIPTICAL AND TRIANGULAR BARS: membrane
analogy, torsion of thin open sections and thin tubes.
UNIT – 5 11 Hours
THERMAL STRESSES: Thermo elastic stress strain relationship, Equations of equilibrium
Thermal stresses in thin circular discs and in long circular cylinder, sphere.
UNIQUENESS THEOREM: Principle of super position, reciprocal theorem, saint venant

principle.
ESSENTIAL READINGS:
1. Advanced Mechanics of solids, L. S. Srinath, Tata Mc. Graw Hill, 2003
2. Theory of Elasticity, S. P. Timoshenko and J. N Gordier, Mc.Graw Hill International, 3rd
edition, 1972
RECOMMENDED READINGS:
1. Theory of Elasticity, Dr. Sadhu Singh, Khanna Publications, 1988
1. Elasticity, Theory, Applications & Numericals, Martin H Sadd, Elsevier. 2005
3. Applied Elasticity, Seetharamu & Govindaraju, Interline Publishing
4. Applied Elasticity, C.T. WANG Sc. D. Mc. Graw Hill Book Co.1953

ME635 MECHANICS OF COMPOSITE MATERIALS
OBJECTIVES:
o An ability to identify the properties of fiber and matrix materials used in commercial
composites, as well as some common manufacturing techniques.
o An ability to predict the elastic properties of both long and short fiber composites based
on the constituent properties.
o An ability to rotate stress, strain and stiffness tensors using ideas from matrix algebra.
OUTCOME:
o To explain the overview of materials.
o To describe the attributes of Materials.
INTRODUCTION TO COMPOSITE MATERIALS: Definition, classification and
characteristics of composite Materials – fibrous composites, laminated composites, particulate
composites.
APPLICATIONS: Automobile, Aircrafts. missiles. Space hardware, Electrical and electronics,
Marine, recreational and sports equipment, future potential of composites.
FIBER REINFORCED PLASTIC PROCESSING: Lay up and curing, fabricating process,
open and closed mould process, hand lay up techniques;structural laminate bag molding,
production procedures for bag molding;filament winding, pultrusion, pulforming, thermo-
forming, injection molding, blow molding.
Micro Mechanical Analysis of a Lamina: Introduction, Evaluation of the four elastic moduli
by Rule of mixture, Numerical problems. Macro Mechanics of a Lamina: Hooke's law for
different types of materials, Number of elastic constants, Two - dimensional relationship of
compliance and stiffness matrix.
Macro Mechanics of a Lamina Hooke's law for two-dimensional angle lamina, engineering
constants - Numerical problems. Stress-Strain relations for lamina of arbitrary orientation,
Numerical problems.
Biaxial Strength Theories: Maximum stress theory, Maximum strain theory, Tsai-Hill theory,
Tsai, Wu tensor theory, Numerical problems.
UNIT – 4 13 Hours
Macro Mechanical Analysis of Laminate: Introduction, code, Kirchoff hypothesis, CL T, A, B,
and D matrices (Detailed derivation) ,Special cases of laminates, Numerical problems
METAL MATRIX COMPOSITES: Reinforcement materials, types, characteristics and
selection base metals selection. Need for production MMC‟s and its application.
FABRICATION PROCESS FOR MMC‟S: Powder metallurgy technique,liquid metallurgy
technique and secondary processing, special fabrication techniques.
STUDY PROPERTIES OF MMC‟S: Physical Mechanical, Wear, machinability and Other
Properties. Effect of size, shape and distribution of particulate on properties.
ESSENTIAL READINGS:
1. Composite Science and Engineering, K. K. Chawla Springer Verlag 1998.
2. Mechanics of composite materials, Autar K. Kaw CRC Press New York.
1. Fiber Reinforced Composites, P. K. Mallick, Marcel Dekker,Inc
2. Mechanics of Composite Materials, Robert M. Jones, McGraw Hill Kogakusha Ltd.1998
3. Composite materials hand book, Meing Schwaitz,” McGraw Hill book company.1984
4. Principles of composite Material mechanics, Ronald F. Gibron. McGraw Hill international,

1994.
5. Mechanics of Composite Materials and Structures, Madhujit Mukhopadhyay , University

Press 2009

ME635 REFRIGERATION AND AIR CONDITIONING

OBJECTIVES:
o To know what is refrigeration and air-conditioning,
o To know the history of refrigeration,
o To know applications of refrigeration and air-conditioning, and
o To describe the term ton of refrigeration and COP.
LEARNING OUTCOME:
o To be able to explain different processes of refrigeration
o To compare different refrigeration cycles
o To estimate performance parameters of different refrigeration cycles
o To describe different physhrometric processes
o To be able to use physhrometric chart and make cooling requirement calculations
o To be able to design winter/summer/round the year air-conditioning system
Note: pre requisite Applied Thermodynamics

UNIT – 1 12 Hours
METHODS OF REFRIGERATION: Ice refrigeration, evaporative refrigeration, air
refrigeration, vapour refrigeration, dry ice refrigeration, thermo electric refrigeration, pulse tube
refrigeration, thermoacoustic refrigeration.
GAS CYCLE REFRIGERATION: Introduction , reverse Carnot cycle, Bell Coleman cycle,
advantages & dis-advtanges of gas refrigeration system. Applications to aircraft refrigeration,
Analysis of gas refrigeration and Numericals.
UNIT – 2 12 Hours
MULTI PRESSURE VAPOUR COMPRESSION SYSTEMS: Multi stage compression,
Multi evaporator systems, Cascade systems, calculation, production of solid carbon dioxide,
System practices for multistage system.

UNIT – 3 12 Hours
REFRIGERANTS: Types of Refrigerants, Comparative study of Ethane and Methane
derivatives, selection of Refrigerants, Requirements of Refrigerants, Effects of lubricants in
Refrigerants, substitutes of CFC Refrigerants, Mixture Refrigerants-azeotropic mixtures
EQUIPMENTS USED IN VAPOUR COMPRESSION REFRIGERATION SYSTEM:

Compressors: Principle, types of compressors, capacity control. Condensers: Types and
construction, Expansion devices: Types- Automatic expansion valve, Thermostatic expansion
valves, capillary tube. Sizing Evaporator: Types & construction.
UNIT-4 12 Hours
VAPOUR ABSORPTION SYSTEM: Common refrigerant absorbent combinations, Binary
mixtures, Ammonia Water Absorption system, Actual vapour absorption cycle and its
representation on enthalpy. composition diagram, calculations. Triple fluid vapour absorption
refrigeration system. Water - Lithium Bromide absorption chiller.
DESIGN CONDITIONS: Outside design conditions, choice of inside conditions, comfort chart.
Choice of supply design condition.
UNIT – 5 12 Hours
LOAD CALCULATIONS AND APPLIED PSYCHOMETRICS: Internal heat gains, system
heat gains, break up of ventilation load and effective sensible heat factor, Bypass factor, cooling
load estimate. Psychometric calculations for cooling. Selection of Air conditioning apparatus for
cooling and dehumidification, evaporative cooling.
TRANSMISSION AND DISTRIBUTION OF AIR: Room Air Distribution, Friction loss in

ducts, dynamic losses in ducts, Air flow through simple Duct system, Duct design.

ESSENTIAL READINGS:
1. „Refrigeration and Air-Conditioning‟ C. P. Arora, Tata McGraw Hill Publication, 2nd

edition, 2001.
2. „Refrigeration and Air-Conditioning‟ W. F. Stoecker, Tata McGraw Hill Publication, 2nd
edition, 1982.
1. „Principles of Refrigeration‟ Dossat, Pearson-2006.

2. „Heating, Ventilation and Air Conditioning‟, McQuistion, Wiley Students edition, 5th
edition 2000.
3. „Air conditioning‟ PITA, 4th edition, pearson-2005
4. „Refrigeration and Air-Conditioning‟ Manohar prasad
5. „Refrigeration and Air-Conditioning‟ S C Arora & S Domkundwar, Dhanpat Rai
Publication

ME635 DESIGN OF HEAT EXCHANGER
UNIT – 1 12 Hours
INTRODUCTION TO HEAT EXCHANGER DESIGN: Types of heat exchangers and their
applications. Flow arrangements and temperature distributions in transfer type of heat
exchangers. Overall heat transfer coefficient;- Clean overall heat transfer coefficient, dirt factor
dirt overall heat transfer coefficient, dirt factors for various process services. Basic design
equation. Mean temperature difference Concept: - LMTD for parallel flow and counter flow
arrangement, correction factor for LMTD for cross flow and multi – pass heat exchangers.
SHELL AND TUBE HEAT EXCHANGERS: Constructional features. Applications.

Effectiveness-NTU method for heat exchanger design/ analysis. Rating and sizing problem.
Correlations for tube side pressure drop and heat transfer coefficients. Pressure drop and heat
transfer coefficient correlations for shell side flow.
UNIT – 2 11 Hours
EFFECT OF BY – PASS AND LEAKAGE CALCULATION PROCEDURE FOR SHELL
AND TUBE HEAT EXCHANGER: Heat balance equations: LMTD: reference temperature
calculations: evaluation of fluid properties: flow assignments: tube side flow area calculations;
viscosity correction factor, shell side equivalent diameter, calculation of shell side heat transfer
coefficient, evaluation for wall temperature, evaluation of overall heat transfer coefficient,
Calculation of surface area. Calculations of tube side and shell side pressure drops.
UNIT – 3 13 Hours
STEAM CONDENSERS: Specifications of other details as per TEMA standards. Flow

arrangement for increased heat recovery: - lack of heat recovery in 1-2 exchangers true
temperature difference in a 2-4 exchanger. Calculation procedure for steam condensers.
DOUBLE PIPE HEAT EXCHANGERS: Constructional features. Applications. Design

parameters :- tube side and shell side film coefficients cut and twist factor, fin efficiency, overall
heat transfer coefficient, mean temperature difference, available surface area, fin geometry fin

height, number of fins, tube side and shell side pressure drop. Calculation procedure for the
design/ analysis of double pipe heat exchange.
UNIT – 4 12 Hours
COMPACT HEAT EXCHANGERS: Introduction; definition of Geometric Terms: plate fin
surface geometries and surface performance data; correlation of heat transfer and friction data;
Goodness factor comparisons; specification of rating and sizing problems; calculation procedure
for a rating problem.
AIR-COOLED HEAT EXCHANGERS: Air as coolant for industrial processes; custom-built
units; fin-tube systems for air coolers; fin-tube bundles; thermal rating; tube side flow
arrangements; cooling air supply by fans; cooling air supply in natural draft towers.
FURNACES AND COMBUSTION CHAMBERS: Introduction; process heaters and boiler;
heat transfer in furnaces: - Heat source; Heat sink; refractory surfaces; heat transfer to the sink;
Design methods: - Method of Lobo and Evans: Method of Wilson, Lobo and Hottel; The Orrok-
Hudson equation; Wallenberg simplified method.
ESSENTIAL READINGS:
1. Process Heat Transfer: Donald Q. Kern, Tata McGraw –Hill Edition (1997)
2. Compact Heat Exchangers: W. M. Kays & A. L. London, Mcgraw –Hill co. (1997)
1. Heat Transfer – A Basic Approach: Necati Ozsisik, McGraw – Hill International edition
(1985).
2. Heat Exchanger Design Hand Book: Volumes 2 and 3, edited by Ernst U schlunder. et. al
Hemisphere Publishing Co. (1983)
3. Heat exchanger- Kokac Thermal- hydraulic and design analysis.

ME635 NON-TRADITIONAL MACHINING
OBJECTIVES:
o Introduction of modern machining methods and their difference with conventional
machining methods,
o Different classification criteria of modern machining methods and their classifications,
o Working principle, process details, applications and advantages and disadvantages
machining.
LEARNING OUTCOME:
o Identify the characteristics of conventional machining and non-traditional machining
o Differentiate between conventional and non-traditional machining
o Classify different non-traditional machining processes
o Identify the need for non-traditional machining processes
o Describe the basic mechanism of material removal in various Non-traditional machining.
o Identify major components of various Non-traditional machines.
o Draw and state the working principle of various Non-traditional machining.
o Identify the process parameters and machining characteristics ofvarious Non-traditional
machines.
o Analyse the effect of process parameters on material removal rate (MRR)
o List the advantages, disadvantages and applications of various Non-traditional
machining processes.
UNIT – 1 13 Hours
INTRODUCTION: History, Classification, comparison between conventional and Non-
conventional machining process selection.
ULTRASONIC MACHINING (USM): Introduction, equipment, tool materials & tool size,
abrasive slurry, cutting tool system design:- Effect of parameter: Effect of amplitude and
frequency and vibration, Effect of abrasive grain diameter, effect of applied static load, effect of

slurry, tool & work material, USM process characteristics: Material removal rate, tool wear,
Accuracy, surface finish, applications, advantages & Disadvantages of USM.
UNIT – 2 11 Hours
ABRASIVE JET MACHINING (AJM): Introduction, Equipment, Variables in AJM: Carrier
Gas, Type of abrasive, size of abrasive grain, velocity of the abrasive jet, mean number. abrasive
particles per unit volume of the carrier gas, work material, stand off distance (SOD), nozzle
design, shape of cut. Process characteristics-Material removal rate, Nozzle wear, Accuracy &
surface finish. Applications, advantages & Disadvantages of AJM. Water Jet Machining:
Principal, Equipment, Operation, Application, Advantages and limitations of water Jet
machinery
UNIT – 3 12 Hours
ELECTROCHEMICAL MACHINING (ECM): Introduction, study of ECM machine,
elements of ECM process : Cathode tool, Anode work piece, source of DC power, Electrolyte,
chemistry of the process, ECM Process characteristics – Material removal rate, Accuracy,
surface finish, ECM Tooling: ECM tooling technique & example, Tool & insulation materials,
Tool size Electrolyte flow arrangement, Handling of slug, Economics of ECM, Applications
such as Electrochemical turning, Electrochemical Grinding, Electrochemical Honing, deburring,
Advantages, Limitations.
CHEMICAL MACHINING (CHM): Introduction, elements of process, chemical blanking

process : Preparation of work piece, preparation of masters, masking with photo resists, etching
for blanking, accuracy of chemical blanking, applications of chemical blanking, chemical milling
(contour machining): process steps –masking, Etching, process characteristics of CHM: material
removal rate, accuracy, surface finish, Hydrogen embrittlement, advantages & application of
CHM.
UNIT - 4 11 Hours
ELECTRICAL DISCHARGE MACHINING (EDM): Introduction, mechanism of metal
removal, dielectric fluid, spark generator, EDM tools (electrodes) Electrode feed control,

Electrode manufacture, Electrode wear, EDM tool design, choice of machining operation,
electrode material selection, under sizing and length of electrode, machining time. Flushing;
pressure flushing, suction flushing, side flushing, pulsed flushing synchronized with electrode
movement, EDM process characteristics: metal removal rate, accuracy, surface finish, Heat
Affected Zone. Machine tool selection, Application, EDM accessories / applications, electrical
discharge grinding, Traveling wire EDM.
UNIT – 5 13 Hours
PLASMA ARC MACHINING (PAM): Introduction, equipment, non-thermal generation of
plasma, selection of gas, Mechanism of metal removal, PAM parameters, process characteristics.
Safety precautions, Applications, Advantages and limitations.
LASER BEAM MACHINING (LBM): Introduction, equipment of LBM mechanism of metal
removal, LBM parameters, Process characteristics, Applications, Advantages & limitations.
ELECTRON BEAM MACHINING (EBM): Principles, equipment, operations, applications,
advantages and limitation of EBM.
ESSENTIAL READINGS:
1. Modern machining process, Pandey and Shan, Tata McGraw Hill 2000
2. New Technology, Bhattacharya 2000

1. Production Technology, HMT Tata McGraw Hill. 2001
2. Modern Machining Process, Aditya. 2002
3. Non-Conventional Machining, P.K.Mishra, The Institution of Engineers (India) Test

book series, Narosa Publishing House – 2005.
4. Metals Handbook: Machining Volume 16, Joseph R. Davis (Editor), American Society of
Metals (ASM)

ME635 PROJECT MANAGEMENT
UNIT 1 11 Hours.
INTRODUCTION: Definition of project, characteristics of projects, understand projects, types
of projects, scalability of project tools, project roles,
PROJECT SELECTION AND PRIORITIZATION – Strategic planning process, Strategic
analysis, strategic objectives, portfolio alignment – identifying potential projects, methods of
selecting projects, financial mode / scoring models to select projects, prioritizing projects,
securing and negotiating projects.
UNIT-2 12 Hours
PLANNING PROJECTS: Introduction, developing the project management plan,
understanding stake holders, communication planning, project meeting management,
communication needs of global and virtual project teams, communication technologies,
Constructing Work Breakdown Structures – scope planning, scope definition, work breakdown
structures (WBS), Using Microsoft project for work breakdown structures.
UNIT -3 13 Hours.
SCHEDULING PROJECTS: purpose of a project schedule, historical development, how
project schedules are limited and created, develop project schedules, uncertainty in project
schedules, Gantt Chart, Using Microsoft Project for critical path schedules.
RESOURCING PROJECTS: Abilities needed when resourcing projects, estimate resource

needs, creating staffing management plant, project ream composition issues, assign resource to
each activity, resource overloads, critical chain project management (CCPM), compress the
project schedule, Using Microsoft Project for resource allocation.
Budgeting Projects: Cost planning, cost estimating, cost budgeting, establishing cost control,
using Microsoft Project for Project Budgets,
UNIT -4 13 Hours.

PROJECT RISK PLANNING: Risk Management Planning, risk identification, risk analysis,
risk response planning, Project Quality Planning and Project Kickoff: Development of quality
concepts, project quality management plan, project quality tools, kickoff project, baseline and
communicate project management plan, using Microsoft Project for project baselines.
PERFORMING PROJECTS: Project supply chain management: - Plan purchasing and

acquisitions, plan contracting, contact types, project partnering and collaborations, project supply
chain management, Leading and Managing Project Teams – Acquiring, developing, managing
and leading the project team, managing stakeholders, managing project conflicts.
UNIT -5 11 Hours
Determining Project Progress and Results: Project Balanced Scorecard Approach, Internal
project, customer, financial issues, Using Microsoft Project to monitor and control projects.
Finishing the project: Terminate project early, finish projects on time, secure customer feedback
and approval, knowledge management, perform administrative and contract closure, celebrate
success and reward participant, provide ongoing support.
ESSENTIAL READING:
1. Project Management, Timothy J Kloppenborg, Cengage Learning, Edition 2009.
2. Project Management, A systems approach to planning schuduing and controlling by

Harold kerzner, CBS publication.
1. Project Management Refer, Pennington Lawrence, Mc Graw hill
2. Project Management, A Moder Joseph and Phillips New Yark Van Nostrand, Reinhold.
3. Project Management, Bhavesh M. Patal, Vikas publishing House

ME635 STATISTICAL QUALITY CONTROL

OBJECTIVES:
o Discuss the role of quality control in production and service operations
o Define and understand the terms chance cause, assignable cause, in control, out of
control, attribute, and variable
o Construct and interpret a Pareto chart
o Construct and interpret a fishbone diagram
o Construct and interpret a mean and range chart
o Construct and interpret a percent defective and a c-bar chart
o Discuss acceptance sampling.
o Construct an operating characteristic curve for various sampling plans.
OUTCOME:
o To describe the fundamentals of statistics (Mean, Median, Mode).

o To explain the control charts for variables.
o To solve the process capability.
o To explain the control charts for attributes.
o To explain the Lot by lot acceptance sampling.
INTRODUCTION: The Meaning of Quality and Quality Improvement; Brief History of
Quality Methodology; Statistical Methods for Quality Control and Improvement; Total Quality
Management (quality philosophy, links between quality and productivity, quality costs, legal
aspects of quality implementing, quality improvement).
MODELING PROCESS QUALITY: Mean, Median, Mode, Standard deviation, Calculating

area, The Deming funnel experiment, Normal distribution tables, Finding the Z score, Central
limit theorem.

METHODS AND PHILOSOPHY OF STATISTICAL PROCESS CONTROL: Chance and
assignable causes, Statistical Basis of the Control Charts (basic principles, choices of control
limits, significance of control limits, sample size and sampling frequency, rational subgroups,
analysis of pattern on control charts, warning limits, Average Run Length-ARL)
CONTROL CHARTS FOR VARIABLES: Control Charts for X-Bar and R- Charts, Type I
and Type II errors, the probability of Type II error. Simple Numerical Problems
UNIT – 3 11 Hours
PROCESS CAPABILITY: The foundation of process capability, Natural Tolerance limits, cp –
process capability index, cpk, pp – process performance index, summary of process measures.
Numerical problems
UNIT 4: 11 Hours
Control Charts For Attributes: Binomial distribution, Poisson distribution (from the point of
view of Quality control) Control Chart for Fraction Nonconforming, Control Chart for number
Nonconforming, Control Charts for Nonconformities or Defects, Control Chart for Number of
non conformities per unit. Numerical problems
LOT-BY-LOT ACCEPTANCE SAMPLING FOR ATTRIBUTES: The acceptance sampling
problem, single sampling plan for attributes, Double, Multiple, and Sequential sampling, AOQL,
LTPD, OC curves, Military Standard 105E, the Dodge-Romig sampling plans. Numerical
problems
ESSENTIAL READINGS:
1. Statistical Quality Control, E.L. Grant and R.S. Leavenworth, 7th edition, McGraw- Hill
publisher.
2. Statistical Quality Control, RC Gupta, Khanna Publishers, New Delhi, 2005

1. Statistical Process Control and Quality Improvement, Gerald M. Smith, Pearson Prentice
Hall. ISBN 0 – 13-049036-9.
2. Statistical Quality Control for Manufacturing Managers, W S Messina, Wiley & Sons,
Inc. New York, 1987
3. Statistical Quality Control, Montgomery, Douglas, 5th Edition, John Wiley & Sons, Inc.
2005, Hoboken, NJ (ISBN 0-471-65631-3).
4. Principles of Quality Control, Jerry Banks, Wiley & Sons, Inc. New York.

ELECTIVE-II (ME735)
ME735 MECHANISM DESIGN
OUTCOME:
o Explain the fundamentals of the theory of kinematics and dynamics of machinery.
o Describe the techniques for studying and designing the motion of machines and its
components.
o Able to adopt computer software packages in modern machine design.
UNIT-1 13 Hours.
Planar Mechanisms and Geometry of Motion: Definitions and basic concepts, Classification
of links, Classification of pairs, Mechanism and machine, Inversions, Grashof‟s law,
Transmission of torque and force in mechanisms, Mobility, Degree of freedom permitted by
joints other than turning and sliding, Equivalent mechanisms, Unique mechanisms.
Number Synthesis: Effect of even or odd number of links on degree of freedom, Minimum
number of binary links in a mechanism, Minimum possible number of turning pairs,
Enumeration of kinematic chain, Degree of freedom of special mechanisms.
UNIT-2 11 Hours.
Synthesis of Linkages: Type, Number and dimensional synthesis, Function generation, Path
generation and body guidance, Precision positions, Structural error, Chebychev spacing, Two
position synthesis of slider crank mechanisms, Crank-rocker mechanisms with optimum
transmission angle.
UNIT-3 12 Hours
Motion Generation: Poles and relative poles, Relative poles of 4-bar mechanism, Relative poles
of slider crank mechanism.
Graphical Methods of Dimensional Synthesis: Two position synthesis of crank and rocker
mechanisms, Three position synthesis, Four position synthesis (point position reduction),
Overlay method.

UNIT-4 11 Hours.
Coupler Curves: Equation of coupler curves, Synthesis for path generation, Graphical synthesis
for path generation, Robert-Chebyshev theorem (cognate linkages), Coupler curves from 5-bar
mechanisms, Examples.
UNIT-5 13 Hours.
Analytical Methods of Dimensional Synthesis: Freudenstein‟s equation for 4-bar mechanism

and slider crank mechanism, Examples, Bloch‟s method of synthesis.
Cams: Introduction, Pressure angle, Parameters affecting pressure angle, Effect of offset
follower motion, Radius of curvature and undercutting, Cams with specified contours.
ESSENTIAL READING:
1. “Theory of Machines & Mechanisms", J.J. Uicker, , G.R. Pennock, J.E. Shigley.
OXFORD 3rd Ed.
2. 'Mechanism & Machine Theory', A.G. Ambekar, PHI, 2007
1. 'Kinematics, Dynamics & Design of Machinery', K. J. Waldron, G. L. Kinzel, Wiley

India, 2007.
2. „Advanced Mechanism Design‟, Erdman sandoor, Vol-l PHI, 2006,
3. “Kinematics & Dynamics of Machinery” H.H. Mabie, F.W. Ocvirk, John Wiley & Sons,
New York, 3rd Ed.

ME735 THEORY OF PLASTICITY

OBJECTIVE:
o This chapter provides a basic theory of plasticity forthe understanding of the
flow curve.
o Differences between the true stress – true straincurve and the engineering
stress – engineeringstrain curves will be highlighted.
o Finally the understanding of the yielding criteria forductile materials will be
made.
OUTCOME
o Solve two and three dimensional problems of cylindrical bodies.
o Know the stress strain relation for a body subjected to loading within elastic
limit.
o Got the relation for a body subjected to thermal expansion.
UNIT – 1 13 Hours
FUNDAMENTAL OF ELASTICITY: Concept of stress, stress transformation laws, spherical
and deviator stress tensors, equilibrium equations, octahedral stresses, concept of strain, deviator
and spherical strain tensors, strain transformation laws, octahedral strains, generalized Hooke‟s
law, elastic strain energy, compatibility equations, theories of strength. problems.
PLASTIC DEFORMATION OF METALS: Crystalline structure in metals, mechanism of

plastic deformation, factors affecting plastic deformation, strain hardening, recovery,
recrystallization and grain growth, flow figures or luder‟s cubes.
CUBICAL DILATION, TRUE STRESS AND STRAIN: Strain tensor, principal strain, plane
strain, spherical and deviator strain, octahedral strain and representative strain, problems.
STRESS STRAIN RELATIONS: Introduction, types of materials, empirical equations,
theories of plastic flow, experimental verification of St.Venant‟s theory of plastic flow, the

concept of plastic potential, the maximum work hypothesis, mechanical work for deforming a
plastic substance.
YIELD CRITERIA: Introduction, yield or plasticity conditions, Von Mises and Tresca criteria,
Geometrical representation, yield surface, yield locus (two dimensional stress space),
experimental evidence for yield criteria, energy required to change the shape with basic principle
problems
SLIP LINE FIELD THEORY: Introduction, basic equations for incompressible two
dimensional flow, continuity equations, stresses in conditions of plain strain, convention for slip
lines, solutions of plastic deformation problem, Geometry of slip line field, Properties of the slip
lines, construction of slip line nets
BENDING OF BEAMS: Analysis for stresses, Non linear stress strain curve, shear stress
distribution, residual stresses in plastic bending, problems.
TORSION OF BARS: Introduction, plastic torsion of a circular bar, elastic perfectly plastic
material, elastic work hardening of material, residual stresses and problems
ESSENTIAL READING:
1.„Theory of Plasticity‟, Chakraborty 3rd Edition Elsevier.
2.„Engineering Plasticity‟, W. Johnson and P. B. Mellor D Van N.O Strand Co. Ltd 2000
1. Basic Engineering Plasticity, DWA Rees 1st Edition Elsevier.
2. Theory of Plasticity, L. S. Srinath TMH,
3. Theory of Plasticity, Sadhu Singh, Kanna publisher

ME735 ENGINEERING DESIGN

OBJECTIVES:
mechanical engineering, the steps involved in designing and the relation of design activity
with manufacturing activity.
o Shall be able to choose proper materials to different machine elements depending on their
physical and mechanical properties. Thus he shall be able to apply the knowledge of
o Student shall gain design knowledge of the different
o t types of elements used in the machine design process. Eg., fasteners, shafts, couplings
etc. and will be able to design these elements for each application
LEARNING OUTCOME:
Enhances the capabilities to assume suitable technical specifications
UNIT 1: 11 Hours.
Design Process: Introduction, History of Design Process, Design by innovation, inadequacies of
traditional design methods, product Design process, product cost, quality and time to market
Detailed description of Design process:

Conceptual design, embodiment design, detail design, planning for manufacture, planning for
distribution, planning for use planning for retirement, marketing, organization for design,
designing to codes and standards, design renew product and process cycles, environmentally
responsible design.
UNIT 2: 13 hours.
Need Identification and Problem Definition: Introduction, identifying customer needs,
gathering information from customers needs, generation of specifications.
Concept Generation and Evaluation: Introduction, creativity, problem solving, creativity

methods, conceptual decomposition, Concept Generation Methods: Brain storming, 6-3-5
method, use of analogies, use of extremes and inverses, Morphological methods. Theory of
inventive problem solving (TRIZ)
Concept Evaluation Methods: Based on feasibility judgment, assessment of technology readiness
based on go-no-go screening, Pugh‟s method
UNIT 3 12 hours.
Embodiment Design & Detail Design : Introduction product architecture, brief introduction to
Configuration Design and parametric design.
Detail Design: Importance of Drawings, Drawings produced during Design process. Bill of
materials: Brief introduction to modeling and simulations, prototypes and testing, rapid
prototyping .Final Design Review.
Materials Selection and Materials in Design :Introduction, general criteria for material
selection, performance characteristics of materials, material selection process, illustration of
Ashby charts, methods of material selection, material performance indices, decision matrices,
Pugh‟s selection method, Weighted property index method, Value analysis.
UNIT 4
Design For X (DFX): General introduction, Design for Manufacture (DFM): Introduction, DFM
guidelines, Specific Design Rules. Design for Assembly (DFA): Introduction, DFA guidelines.
Design for Reliability (DFR): Introduction, Bath-tub curve, Mean life, MTTF and MTBF,

Failure rate(Constant and Variable), Exponential and Weibull reliability functions, System
reliability concepts-Series and Parallel systems.
Design for Environment (DFE): Introduction, DFE practices, Introduction to Design for Test and
Maintenance(Serviceability),Introduction to Industrial Design.
UNIT 5: 12 Hours.
Cost Considerations and Human Factors in Engineering Design:
Robust and Quality Design: Introduction, concept of total quality control and assurance,
Taguchi‟s quality loss functions, Robust design: Parameter design and tolerance design.
ESSENTIAL READINGS
1. Engineering Design: A Materials and Processing Approach: George E. Dieter, Mc Graw

Hill, 1991.
2. The Mechanical Design Process, David G. Ullman, Mc Graw Hill, 2003
RECOMMENDED READING
1. Product Design & Development: Karl T. Ulrich & Steven D, Epinger, Tata Mc Graw Hill,
3rd Edition, 2003
2. Engineering Design Principles: Ken Hurst, Elsevier, 2010
3. An introduction to Engineering Design Method: V Gupta and P Murthy, Tata Mc Graw

Hill, 2000
4. Introduction of Engineering Design: T. Woodson, McGraw Hill, 2001
5. Design & Planning of Engineering systems: D. D. Meredith, K.W. Wong, R.W.Woodhead

& K. K.Worthman,2000
6. Introduction to Design: M.A. Asimov, Prentice Hall, 1996
7. Product Design and Manufacturing: A.C. Chitale and R.C. Gupta, PHI 4TH edition 2007

ME735 GAS DYNAMICS

OBJECTIVES:
o To familiarize with behavior of compressible gas flow

o To understand the difference between subsonic and supersonic flow
o To familiarize with high speed test facilities
OUTCOME:
Ability to
o To distinguish between various flow regimes
o To analyse the flow under different flow conditions
To assess the flow behavior and consequent loads due to flow
UNIT – 1 11 Hours
FUNDAMENTAL EQUATIONS OF STEADY FLOW: Continuity and momentum
equations, The thrust function, The dynamic equation and Euler‟s Equation. Bernoulli‟s
Equation. Steady flow energy equation.
UNIT-2 12 Hours.
ISENTROPIC FLOW: Acoustic velocity, Mach number, Mach cone and Mach angle. Flow
parameters, stagnation temperature, pressure, and density.
ADIABATIC FLOW: Stagnation temperature change. Rayleigh line, Pressure ratio and
temperature ratio, Entropy considerations, maximum heat transfer.
UNIT – 3 12 Hours
FLOW WITH FRICTION: The fanning equation, Friction factor and friction parameter, Fanno
line, Fanno equations.
WAVE PHENOMENA: Classification of wave phenomena, analysis of shock phenomena,
Hugoniot equation. Weak waves, compression waves, Normal shock waves, oblique shock
waves, Entropy considerations, Rayleigh Pilot equations, detonation and deflageration.

VARIABLE AREA FLOW: Velocity variation with Isentropic flow, Criteria for acceleration
and deceleration. Effect of pressure ratio on Nozzle operation. Convergent nozzle and
convergent divergent nozzle. Effect of back pressure on nozzle flow. Isothermal flow functions.
Comparison of flow in nozzle. Generalized one dimensional flow.
Applications of dimensional analysis and similitude to gas dynamic problems.
INTRODUCTION TO FLAMES AND COMBUSTION: Flame propagation, diffusion
flames, premixed flames, flame velocity, theories of flame propagation, ignition for combustible
mixture, flame stabilization.
ESSENTIAL READINGS:
1. Fundamentals of Compressible flow: Yahya, 2nd Edn. 1991; Wieley Eastern.
2. Gas Dynamics, E Radhakrishnan PHI-2006
1. Introduction to Gas Dynamics: Rolty, wiley 1998
2. Elements of Gas Dynamics: Liepmann and roshko, Wiley 1994.
3. The dynamics and thermodynamics of compressible fluid flow: Shapiro Ronold press.
1994.
4. Compressible Fluid Flow, J. F. Anderson

ME735 AUTOMATION IN MANUFACTURING

OBJECTIVES:
o Define what is meant by a manufacturing system
o Specify the general material handling processes that may be distinguished
o List the types of work transport to be encountered, and the equipment used tocarry it out
o Explain what computer functions are utilised in automated manufacturing
o Describe why the number of workstations has an impact upon the type of manufacturing
system implemented.
o Explain why workstation layout is an important consideration in the manufacturing
system
o Define what is meant by the manning level of a workstation, and list the levels
themselves for single and multi-station systems
o Specify the importance of part or product variety for manufacturing systems
o Describe single- and multi-station systems
o List the enablers for unattended cell operation
o Calculate the length of time that the automated cell can theoretically operateunattended
o Determine the number of workstations that are required in a system
o Define a machine cluster
LEARNING OUTCOME:
o Explain automation in Production systems, Automation principles & Strategies.
o Understand the different Manufacturing Operations.
o Identify the different types of industrial control system and automated manufacturing
systems.
o describe the concept of group technology & flexible manufacturing systems.
o Classify the different method of quality control systems and inspection technologies.
o explain the different manufacturing support systems in the industries.
INTRODUCTION: Production System Facilities, Manufacturing Support systems, Automation
in Production systems, Automation principles & Strategies

MANUFACTURING OPERATIONS: Manufacturing Operations, Product/Production

Relationship, Production concepts and Mathematical Models & Costs of Manufacturing
Operations
INDUSTRIAL CONTROL SYSTEM: Basic Elements of an Automated System, Advanced
Automation Functions & Levels of Automation, Continuous versus Discrete control, Computer
Process control, Forms of Computer Process Control.
AUTOMATED MANUFACTURING SYSTEMS: Components of a Manufacturing systems,
Classification of Manufacturing Systems, overview of Classification Scheme, Single Station
Manned Workstations and Single Station Automated Cells.
GROUP TECHNOLOGY & FLEXIBLE MANUFACTURING SYSTEMS: Part Families,
Parts Classification and coding, Production Flow Analysis, Cellular Manufacturing, Flexible
Manufacturing Systems: What is an FMS, FMS Components, FMS Applications & Benefits, and
FMS Planning & Implementation Issues.
UNIT -4 12 Hours.
QUALITY CONTROL SYSTEMS: Traditional and Modern Quality Control Methods,
Taguchi Methods in Quality Engineering. Introduction to SQC Tools.
INSPECTION TECHNOLOGIES: Automated Inspection, Coordinate Measuring Machines

Construction, operation & Programming, Software, Application & Benefits, Flexible Inspection
System, Inspection Probes on Machine Tools, Machine Vision, Optical Inspection Techniques &
Noncontact Nonoptical Inspection Technologie
MANUFACTURING SUPPORT SYSTEM: Process Planning, Computer Aided Process
Planning, Concurrent Engineering & Design for Manufacturing, Advanced Manufacturing

Planning, Just-in Time Production System, Basic concepts of lean and Agile manufacturing.
Basic Concepts of Lean and Agile manufacturing, Comparisons of Lean & Agile Manufacturing.
ESSENTIAL READINGS:
1. Automation, Production Systems and Computer Integrated Manufacturing, M.

P. Groover, Pearson education. Third Edition, 2008
2. Principles of CIM, Vajpayee, PHI.
1. Anatomy of Automation, Amber G.H & P. S. Amber, Prentice Hall.
2. Performance Modeling of Automated Manufacturing Systems, Viswanandham,

PHI
3. Computer Based Industrial Control, Krishna Kant, EEE-PHI

ME735 TOTAL QUALITY MANEGEMENT

OBJECTIVE:
o Process improvement
o Defect prevention
o Priority of effort
o Developing cause-effect relationships
o Measuring system capacity
o Developing improvement checklist and check forms
o Helping teams make better decisions
o Developing operational definitions
o Separating trivial from significant needs
o Observing behaviour changes over a period of time
LEARNING OUTCOME
o Student will be Able to apply quality philosophy in his work.
o Able to apply TQM philosophy for the benefit of the organization by imparting training.
o Able to apply the philosophy to minimize defects and retain customer satisfaction at all
levels.
o Able to analyse and pinpoint defects generated from various production units and
control them.
Principles and Practice: Definition, basic approach, gurus of TQM, TQM Framework,
awareness, defining quality, historical review, obstacles, benefits of TQM.
Leadership: Definition, characteristics of quality leaders, leadership concept, characteristics of

effective people, ethics, the Deming philosophy, role of TQM leaders, implementation, core
values, concepts and framework, strategic planning communication, decision making,

Customer Satisfaction and Customer Involvement: Customer Satisfaction : customer and
customer perception of quality, feedback, using customer complaints, service quality, translating
needs into requirements, customer retention, Case studies.
Employee Involvement – Motivation, employee surveys, empowerment, teams, suggestion
system, recognition and reward, gainsharing, performance appraisal, unions and employee
involvement, case studies.
UNIT – 3 12 hours.
Continuous Process Improvement: process, the Juran trilogy, improvement strategies, types of
problems, the PDSA Cycle, problem-solving methods, Kaizen, reengineering, six sigma, case
studies.
Tools and Techniques: Benching marking, information technology, quality management

systems, environmental management system, quality function deployment, quality by design,
failure mode and effect analysis, product liability, total productive maintenance.
Quality Management Tools : Why Why, forced filed analysis, nominal group technique,
affinity diagram, interrelationship digraph, tree diagram, matrix diagram, prioritization matrices,
process decision program chart, activity network diagram.
Statistical Process Control : Pareto diagram, process flow diagram, cause-and-effect diagram,
check sheets, histograms, statistical fundamentals, Control charts, state of control, out of control
process, control charts for variables, control charts for attributes, scatter diagrams, case studies.
UNIT – 5 12 hours.
Building and Sustaining Performance Excellence in Organizations : Making the commitment
to total quality, organizational culture and total quality, change management, sustaining the
quality organization, self-assessment processes, implementing ISO 9000, Baldrige, and sis
sigma, a view toward the futures

Design for Six Sigma: Tools for concept development, tools for design development, tools for
design optimization, tools for design verification, problems.
ESSENTIAL READINGS:
1. Total Quality Management: Dale H. Bester field, Publisher - Pearson Education India,
ISBN: 8129702606, Edition 03/e Paperback (Special Indian Edition)
2. Total Quality Management for Engineers: M. Zairi, ISBN: 1855730243, Publisher: Wood
head Publishing
1. A New American TQM, four revolutions in management, Shoji Shiba, Alan Graham,
David Walden, Productivity press, Oregon, 1990
2. 100 Methods for Total Quality Management: Gopal K. Kanji and Mike Asher, ISBN:
0803977476, Publisher: Sage Publications, Inc.; Edition – 1
3. Organisational Excellence through TQM, H. Lal, New age pub, 2008

ELECTIVE –III (ME736)

ME736 EXPERIMETAL STRESS ANALYSIS
OBJECTIVES
o To understand the relation between the mechanics theory and experimental stress
analysis.
o To establish the fundamental concepts and newly experimental techniques.
o To be able to use the experimental techniques on the practical problems.
o To be able to make a fine presentation related to the experimental paper.
LEARNING OUTCOME
o To describe the Sensitivity & the construction of strain gauges.
o To elucidate the isoclinics & Fringe multiplication techniques.
o To explain the stress separation methods of 3D photoelasticity.
o To describe the Birefringence coating techniques.
o To describe the Moire’s Techniques.
UNIT-1 13 Hours.
Electrical Resistance Strain Gages: Strain sensitivity in metallic alloys, Gage

construction, Adhesives and mounting techniques, Gage sensitivity and gage factor,
Performance'Characteristics, Environmental effects, Strain Gage circuits. Potentiometer,
Wheatstone's bridges, Constant current circuits.
Strain Analysis Methods: Two element, three element rectangular and delta rosettes, Correction
for transverse strain effects, Stress gage, Plane shear gage, Stress intensity factor gage.
UNIT-2 11 Hours.
Photoelasticity: Nature of light, Wave theory of light - optical interference , Stress optic law –
effect of stressed model in plane and circuclar polariscopes, Isoclinics & Isochromatics,
Fringe order determination Fringe multiplication techniques , Calibration photoelastic model
materials

UNIT-3 12 hours.
Two Dimensional Photoelasticity: Separation methods: Shear difference method, Analytical

separation methods, Model to prototype scaling, Properties of 2D photoelastic model
materials, Materials for 2D photoelasticity
Three Dimensional Photo elasticity: Stress freezing method, Scattered light photoelasticity,
Scattered light as an interior analyzer and polarizer, Scattered light polariscope and stress
data Analyses.
UNIT-4 13 Hours.
Photoelastic (Birefringent) Coatings : Birefringence coating stresses, Effects of

coating thickness: Reinforcing effects, Poission's, Stress separation techniques: Oblique
incidence, Strip coatings Brittle
Coatings: Coatings stresses, Crack patterns, Refrigeration techniques, Load relaxation
techniques, Crack detection methods, Types of brittle coatings, Calibration of coating.
Advantages and brittle coating applications.
UNIT-5 11 Hours.
Moire Methods: Moire fringes produced by mechanical interference .Geometrical approach,

Displacement field approach to Moire fringe analysis ,0ut of plane displacement measurements,
Out of plane slope measurements .Applications and advantages
ESSENTIAL READINGS:
1. "Experimental Stress Analysis", Dally and Riley, McGraw Hill.
2. "Experimental Stress Analysis". Sadhu Singh, Khanna publisher.
3. Experimental stress Analysis, Srinath L.S tata Mc Graw Hill.

REFERENCES BOOKS :
1. "Photoelasticity Vol I and Vol II, M.M.Frocht, John Wiley & sons.
2. "Strain Gauge Primer", Perry and Lissner,
3. "Photo Elastic Stress Analysis", Kuske, Albrecht & Robertson John Wiley & Sons.
4. "Motion Measurement and Stress Analysis", Dave and Adams,

ME736 CRYOGENICS
OBJECTIVES
The goal of this program is to provide:
 A fundamental and theoretical foundation of knowledge pertaining to Cryogenic
 A concrete grasp of the applications of Cryogenics Engineering as it is used in the
aerospace industry.
UNIT– 1 ` 11 Hours.
INTRODUCTION TO CRYOGENIC SYSTEMS:
Applications Areas of Cryogenic Engineering
Low temperature properties of engineering materials – Mechanical properties, Thermal
properties, Electrical properties.
Introduction The Thermodynamically Ideal system Production of low temperatures – Joule
Thompson Effect, Adiabatic expansion.
UNIT– 2 13 Hours.
GAS LIQUIFICATION SYSTEMS: Liquification systems for Air Simple Linde – Hampson
System, Claude System, Heylndt System, Dual pressure, Claude.
Liquefaction cycle Kapitza System. Comparison of Liquefaction Cycles Liquefaction cycle for
hydrogen, helium and Neon, Critical components of liquefaction systems.
GAS CYCLE CRYOGENIC REFRIGERATION SYSTEMS: Classification of Cryo coolers
Stirling cycle Cryo – refrigerators, Ideal cycle – working principle. Schmidt‟s analysis of Stirling
cycle Various configurations of Stirling cycle refrigerators Integral piston Stirling cryo-cooler,
Free displacer split type Stirling Cryo coolers, Gifford Mcmahon Cryo- refrigerator, Pulse tube
refrigerator, Solvay cycle refrigerator, Vuillimier refrigerator, Cryogenic regenerators.
UNIT- 3 13 Hours.
GAS SEPARATION AND GAS PURIFICATION SYSTEMS: Thermodynamic ideal
separation system, Properties of mixtures, Principles of gas separation, Linde single column air
separation. Linde double column air separation, Argon and Neon separation systems. Adsorption
Process, PSA systems.

ULTRA LOW TEMPERATURE CRYO – REFRIGERATORS:

Magneto Caloric Refrigerator 3He-4He Dilution refrigerator. Pomeranchuk cooling.
Measurement systems for low temperatures, Temperature measurement at low temperatures,
Resistance thermometers, Thermocouples, Thermistors, Gas Thermometry. Liquid level sensors.
VACUUM TECHNOLOGY: Fundamental principles. Production of high vacuum, Mechanical
vacuum pumps, Diffusion pumps, Cryo-pumping, Measurement of high vacuum level.
Cryogenic Insulation: Heat transfer due to conduction, Evacuated porous insulation Powder &
Fibers Opacified powder insulation, Gas filled powders & Fibrous materials Multilayer super-
insulation, Composite insulation.
UNIT-5 13 Hours
CRYOGENIC FLUID STORAGE AND TRANSFER SYSTEMS: Design of cryogenic fluid
storage vessels, Inner vessel, Outer Insulation, Suspension system, Fill and drain lines.
Cryogenic fluid transfer, External pressurization, Self pressurization, Transfer pump.
APPLICATION OF CRYOGENIC SYSTEMS: Cryogenic application for food preservation –

Instant Quick Freezing techniques 11.2 Super conductive devices, Cryogenic applications for
space technology.
ESSENTIAL READINGS:
1. Cryogenic Systems, Randall Barron – Oxford Press, 1985
2. Cryogenic Engineering, Thomas M. Flynn, Marcel Dekker, Inc N.Y. Basal 1997
REFERENCE BOOK:
1. Cryogenic Process Engineering, Klaus D. Timmerhaus & Thomas M. Flynn, Plenum

Press, New York & London 1989.

ME736 SMART MATERIALS

OBJECTIVES
o Identify the strengths of a given class of materials regarding their use as smart materials.
o Identify the weaknesses of a given class of materials regarding their use as smart
materials.
o Select a candidate smart material for a given orthodontic application.
o Factor the strengths and weaknesses of a smart material into the design of a product in
orthodontic application
LEARNING OUTCOMES:
o To explain the overview of Smart materials.
o To describe the attributes of Smart Materials.
o To explain the operation of Smart Sensors.
o To elucidate the signal conditioning techniques.
INTRODUCTION: Characteristics of composites and ceramics materials, Dynamics and

controls, concepts, Electro-magnetic materials and shape memory alloys-processing and
characteristics
UNIT-2 11 Hours
SENSING AND ACTUATION: Principals of electromagnetic, acoustics, chemical and
mechanical sensing and actuation, Types of sensors and their applications, their compatibility
writer conventional and advanced materials, signal processing, principals and characterization.
UNIT -3 13 Hours.
CONTROL DESIGN: Design of shape memory alloys, Types of MR fluids, Characteristics and
application, principals of MR fluid value designs, Magnetic circuit design, MR Dampers, Design
issues.
OPTICS AND ELECTROMAGNETIC: Principals of optical fiber technology, characteristics
of active and adaptive optical system and components, design and manufacturing principles.

UNIT-4 12 Hours.
STRUCTURES: Principles of drag and turbulence control through smart skins, applications in
environment such as aerospace and transportation vehicles, manufacturing, repair and
maintainability aspects.
Controls: Principles of structural acoustic control, distributed, amalog and digital feed back
controls, Dimensional implications for structural control.
UNIT - 5
PRINCIPLES OF VIBRATION AND MODAL ANALYSIS: PZT Actuators, MEMS,

Magnetic shape Memory Alloys, Characteristics and Applications.
INFORMATION PROCESSING: Neural Network, Data Processing, Data Visualisation and

Reliability – Principals and Application domains.
TEST BOOKS:
1. Analysis and Design‟, A. V. Srinivasan, „Smart Structures –Cambridge University Press,

New York, 2001, (ISBN : 0521650267)
2. „Smart Materials and Structures‟, M V Gandhi and B S Thompson Chapmen & Hall,
London, 1992 (ISBN : 0412370107)
1. „Smart Materials and Structures‟, Banks HT, RC Smith, Y Wang, Massow S A, Paris
1996
2. G P Gibss‟Adaptive Structres‟, Clark R L, W R Saunolers, Jhon Wiles and Sons, New

York, 1998
3. An introduction for scientists and Engineers‟, Esic Udd, Optic Sensors : Jhon Wiley &
Sons, New York, 1991 (ISBN : 0471830070)

ME736 AGILE MANUFACTURING
AGILE MANUFACTURING: Definition, business need, conceptual frame work,

characteristics, generic features.
DEVELOPING AGILE MANUFACTURING: Enterprise, Strategies, integration of
organization, workforce and technology, reference models, examples.
INTEGRATION OF PRODUCT /PROCESS DEVELOPMENT: Principles, Robust design

approach, Approaches to enhance ability in manufacturing, Role of QFD, Managing people in
Agile orgnisation, Approaches.
APPLICATION OF IT/IS CONCEPTS IN AGILE MANUFACTURING: Strategies,

Management of complexities and information. flow, approaches, applications of multimedia to
improve agility in manufacturing, system concepts.
AGILE SUPPLY CHAIN MANAGEMENT: Principles, IT/IS concepts in supply chain
management, enterprise integration and management in agile manufacturing, concepts, Agility,
Adaptability and learners – comparison of concepts.
COMPUTER CONTROL OF AGILE MANUFACTURING: CAPP for Agile

Manufacturing, Aggregate capacity planning and production line design / redesign in Agile
manufacturing, Cellular manufacturing, concepts, examples.
UNIT – 5 ` 11 Hours.
CORPORATE KNOWLEDGE MANAGEMENT IN AGILE MANUFACTURING:

Strategies, strategic options in Agile manufacturing, Role of standards.

DESIGN OF SKILL & KNOWLEDGE: Enhancing technology for Machine tool system,
Resumption of design requirement geometry, definition, methods, decision support for selection
of cutting parameters, design enhancements, parametric approach only.
ESSENTIAL READINGS:
1. „Agile Manufacturing- Forging Mew Frontiers‟, Poul T Kidd, Amagow Co. UK, ISBN-
0-201-63163-6, 1994
2. „„Agile Manufacturing”, A Gunasekharan, the 21st Century Competitive strategy, ISBN -

13 978-0-08-04 3567-1, Elsevier Press, India
1. O Levine Transitions to Agile Manufacturing, Joseph C Moutigomery and Lawrurence –

Staying Flexible for competitive advantage, ASQC quality press, Milwaukee.
Wisconsiw, USA 1996
2. Agile Development for Mass Customization, David M Andeson and B Joseph Pine, Irwin
Professional Publishing, Chicogo USa 1997

ME736 FINANCIAL MANAGEMENT
OBJECTIVES:
This course is designed as a survey course for students in a graduate management program. We
will begin with a general overview of financial statements and then go into more detail about
financial concepts, financial instruments and techniques used in financial decision-making.
The main objectives of this course are to introduce you to the:
o world of finance. Anyone involved in the management of a business needs to have a basic
knowledge of business finance and
o basic financial concepts such as the time value of money, asset valuation, and risk and
return.
INTRODUCTION TO FINANCIAL MANAGEMENT: Forms of organization, direct and
indirect taxes. Statutory Registration- excise Duty, central sales tax, VAT, service tax,
international fund availability.
RISK AND REQUIRED RETURN: Risk and return relationship, methods of measuring the
risk, Business risk, financial risk, calculation of expected rate of return to the portfolio,
numerical problems.
WORKING CAPITAL MANAGEMENT: Definition, need and factors influencing the
working capital requirement. Determination of operating cycle, cash cycle and operating cycle
analysis. Calculation of gross working capital and net working capital requirement.
LONG TERM FINANCING: Raising of finance from primary and secondary markets.
Valuation of securities, features of convertible securities and warrants. Features of debt, types of
debt instruments, return on investment(ROI) and credit rating of units. Shares, debentures.

INTRODUCTION: Book keeping – systems of book keeping, journal and ledger posting.
Financial Statement, Preparation of Trial balance, profit and Loss Account, Balance Sheet with
adjustments.
RATIO ANALYSIS / ACCOUNTING RATIO: Liquidity ratio – Current ratio, quick ratio,
turnover ratio, capital structure ratio- Debt – equity ratio, Coverage ratio, Profitability ratio,
Profit margin, Return on assets, Activity ratios – Inventory turnover ratio, Debtors Turnover
ratio. Preparation of the balance sheet from various ratios. Analysis of any one published
balanced sheet.
COSTING: Classification of cost, preparation of cost sheet, absorption and variable costing, job
costing, process costing. Classification of the variances analysis – material, labour and overhead
variances.
BUDGETING: Types of budgets – Flexible budgets, preparation of cash budgets, purchase and
production budgets and master budget, Budgetory control, advantages & limitations of
budgeting.
ESSENTIAL READINGS:
1. Financial Management, Khan & Jain, text & problems TMH ISBN 0-07-460208-A.
20001
2. Financial Accounting, Costing and Management Accounting, S. M. Maheshwari, 2000
1. Financial Management, I. M. Pandey, Vikas Publication House ISBN 0-7069-5435-1.

2002
2. Financial Management, Abrish Gupta, Pearson.
3. Financial Decision Making, Humpton. 2000
4. Financial Management, Theory and Practice, Prasanna Chandra TMH ISGN -07-462047-9,
3rd edition 2002

ME736 INTERNAL COMBUSTION ENGINES
OBJECTIVE:
The aim of this technical report is:
 Introducing different types of internal combustion engines, based on different

categorization.
 Familiarization with the mechanism of operation of each, and the thermodynamic
relations behind its theoretical cycles.
LEARNING OUTCOMES
o By studying this course students will be able to
o Classify IC Engines and explain their working
o Explain different thermodynamic cycles on which engines work and derive expressions
for mean effective pressure and efficiency
o Compare different engines
o Describe engine knocking and parameters effecting engine knocking
o Explain the working of engine cooling, carburetion, and injection system
o Application of dual fuel operation and modern technolology in combustion, design and
fuel systems
o Explain vehicular pollution and its control methods
UNIT – 1 7 Hours
THERMODYNAMIC CYCLE ANALYSIS: Deviation from ideal processes. Effect of
chemical equilibrium and variable specific heats. Effect of air fuel ratio and exhaust gas dilution.
Calculation of combustion temperatures. Use of combustion charts. Simple. numerical problems.
COMBUSTION IN C.I. ENGINES: Ricardo's three stages of combustion process in C.I.
engines. Delay period & factors affecting delay period. Diesel knock- Methods of controlling
diesel knock. Knock rating of Diesel fuels.

UNIT -2 6 Hours
COMBUSTION CHAMBERS: Requirements of combustion chambers. Features of different
types of combustion chambers system for S.I. engine. I-head, F-head combustion chambers. C.I.
engine combustion chambers-Air swirl turbulence-M. type combustion chamber. Comparison of
various types of combustion chambers.
UNIT -3 6 Hours
CARBURATION AND COMBUSTION PROCESS IN S.I. ENGINES: Mixture
requirements in S.I engine. Simple Carburetor and its limitations. Knock fee and knocking
combustion-Theories of combustion process in S.I. engines. Effect of Knock on engine
performance. Effect of operating variables on knocking. Knock rating of fuels-octane number.
HUCR values. Anti knock agents - Pre ignition - Post ignition.
UNIT – 4 8 Hours
FUELS: Hydro carbons - chemical structure-influence of chemical structure on knock
alternative fuels-Alcohols-vegetable oils- Bio gas as Diesel engine fuels.
5 Hours
FUEL INJECTION SYSTEMS: Diesel injection systems-jerk pump injectors Nozzles of
different types-Petrol injection systems for S.I. engines-Electronic fuel injection system. Cooling
system- Water cooling, air cooling & liquid cooling-role of thermostats-radiator construction.
UNIT - 5 7 Hours
EMISSION REGULATION AND CONTROL SYSTEMS: Mechanism of pollutant
formation. Total emission control package thermal reactor package-catalytic converter package-
control of NOX -Exhaust gas recirculation-Water injection.

MODERN DEVELOPMENTS: Turbo charging and super charging of I.C.engines, Stratified
charge engines (Lean burned SIengine) Multi fuel engines, Rotary piston engine, Two injector
engines Pilot ignition engine, all ceramic swirl chamber engines.
ESSENTIAL READING:
1. A course in I.C. Engines, M. L. Mathur and R. P. Sharma 20001.
2. Internal Combustion Engines, Colin R. Ferguson C. John Wiley & sons, 1986
1. I.C. Engines, Edward. F. Obert, Harper International edition, 1973.
2. Internal Combustion Engines, Ganeshan, Tata McGraw Hill, 2nd Edition, 2003.
3. Engineering Fundamentals of the I.C. Engine, Willard W. Pulkrabek. 1998.
4. Combustion Engine Process, Lichty, Judge 2000

ELECTIVE-IV (ME833)
ME833 TRIBOLOGY
OBJECTIVE:
o Describe surface topography, physico-chemical aspects of solid surfaces, and surface

interactions.
o Analyze the mechanics of solid elastic and elastoplastic contacts.
o Recognize the laws of friction, mechanisms of friction, friction space, stiction, stick slip,
and surface temperature.
o Appreciate the various modes of wear: adhesive, delamination, fretting, abrasive, erosive,
corrosive, oxidational (mild and severe), melt, and the wear-mechanism maps.
o Identify types of lubrication: boundary, solid-film, hydrodynamic, and hydrostatic
lubrication.
o Examine applications/case studies: sliding contacts, rolling contacts, bearing design,
coating selection, and lubrication.
o Explore the design of tribological surfaces and how to troubleshoot tribology problems.
o Survey tribological testing devices and testing design.
INTRODUCTION TO TRIBIOLOGY: Properties of oils and equation of flow: Viscosity,
Newton‟s Law of viscosity, Hagen-Poiseuille Law, Flow between parallel stationary planes,
viscosity measuring apparatus. Lubrication principles, classification of lubricants.
HYDRODYNAMIC LUBRICATION: Friction forces and power loss in lightly loaded
bearing, Petroff‟s law, Tower‟s experiments, idealized full journal bearings.
MECHANISM OF PRESSURE DEVELOPMENT IN AN OIL FILM: Reynold‟s
investigations, Reynold‟s equation in two dimensions. Partial journal bearings, end leakages in
journal bearing, numerical problems.

SLIDER / PAD BEARING WITH A FIXED AND PIVOTED SHOE: Pressure distribution,
Load carrying capacity, coefficient of friction, frictional resistance in a pivoted shoe bearing,
influence of end leakage, numerical examples.
OIL FLOW AND THERMAL EQUILIBRIUM OF JOURNAL BEARING: Oil flow
through bearings, self-contained journal bearings, bearings lubricated under pressure, thermal
equilibrium of journal bearings.
HYDROSTATIC LUBRICATION: Introduction to hydrostatic lubrication, hydrostatic step
bearings, load carrying capacity and oil flow through the hydrostatic step bearing.
BEARING MATERIALS: Commonly used bearings materials, properties of typical bearing
materials. Wear: Classification of wear, wear of polymers, wear of ceramic materials, wear
measurements, effect of speed, temperature and pressure.
BEHAVIOR OF TRIBOLOGICAL COMPONENTS: Selection, friction, Wear of ceramic
materials, wear measurements, effects of speed, temperature and pressure. Tribological
measures, Material selection, improved design, surface engineering.
ESSENTIAL READINGS:
1. Fundamentals of Tribiology , Basu S K., Sengupta A N., Ahuja B. B., , PHI 2006
2. Introduction to Tribiology Bearings, Mujumdar B. C., S. Chand company pvt. Ltd 2008.
REFERENEC BOOKS:
1. Theory and Practice of Lubrication for Engineers, Fuller, D., New York company 1998
2. Principles and Applications of Tribiology, Moore, Pergamaon press 1998
3. Tribiology in Industries, Srivastava S., S Chand and Company limited, Delhi 2002
4. Lubrication of bearings – Theoretical Principles and Design, Redzimovskay E I., Oxford

press company 2000

ME833 FRACTURE MECHANICS

OBJECTIVE:
The course will treat linear and nonlinear fracture mechanics principles and their applications
to structural design. Fracture phenomena in metals and nonmetals will be discussed and testing
methods will be highlighted. In the end computer assisted techniques for fracture study will be
discussed
LEARNING OUTCOME:
o Predict material failure for any combination of applied stresses.
o Estimate failure conditions of a structure.
o Determine the stress intensity factor for simple components of simple geometry.
o Predict the likelihood of failure of a structure containing a defect.
FRACTURE MECHANICS PRINCIPLES: Introduction, Mechanisms of Fracture, a crack in
structure, the Griffith‟s criterion, modern design – strengths, stiffness and toughness. Stress
intensity approach
STRESS ANALYSIS FOR MEMBERS WITH CRACKS: Linear elastic fracture mechanics,
Crack tip stress and deformations, Relation between stress intensity factor and fracture
toughness, Stress intensity based solutions. Crack tip plastic zone estimation, Plane stress and
plane strain concepts. The Dugdale approach, the thickness effect.
ELASTIC – PLASTIC FRACTURE MECHANICS: Introduction, Elasto–plastic factor
criteria, crack resistance curve, J-integral, Crack opening displacement, crack tip opening
displacement. Importance of R-curve in fracture mechanics, experimental determination of J-
integral, COD and CTOD.
UNIT -3 13 Hours.
DYNAMIC AND CRACK ARREST: Introduction, the dynamic stress intensity and elastic
energy release rate, crack branching, the principles of crack arrest, the dynamic fracture
toughness.

FATIGUE AND FATIGUE CRACK GROWTH RATE: Fatigue loading, various stages of
crack propagation, the load spectrum, approximation of the stress spectrum, the crack growth
integration, fatigue crack growth laws.
FRACTURE RESISTANCE OF MATERIALS: Fracture criteria, fatigue cracking criteria,
effect of alloying and second phase particles, effect of processing and anisotropy, effect of
temperature, closure.
COMPUTATIONAL FRACTURE MECHANICS: Overview of numerical methods,
traditional methods in computational fracture mechanics – stress and displacement marching,
elemental crack advance, virtual crack extension, the energy domain integral, finite element
implementation. Limitations of numerical fracture analysis.
FRACTURE TOUGHNESS TESTING OF METALS: Specimen size requirements, various
test procedures, effects of temperature, loading rate and plate thickness on fracture toughness.
Fracture testing in shear modes, fatigue testing, NDT methods.
ESSENTIAL READINGS:
1. Introduction to Fracture Mechanics, Karen Hellan McGraw Hill Pub.2000
2. Fracture of Engineering Brittle Materials, Jayatilake, Applied Science, London. 2001.
1. Fracture Mechanics – Fundamentals and Application, T.L. Anderson, CRC press 1998
2. Elementary Engineering Fracture Mechanics, David Broek, Artinus Nijhoff, London

1999.
3. Fracture and Fatigue Control in Structures, Rolfe and Barsom, Printice Hall 2000.
4. Fundamentals of Fracture Mechanics, Knott, Bureworth 2000.

ME833 POWER PLANT ENGINEERING

OBJECTIVE:
o Describe sources of energy and types of power plants
o Analyze different types of steam cycles and estimate efficiencies in a steam power plant
o Describe basic working principles of gas turbine and diesel engine power plants. Define
the performance characteristics and components of such power plants
o List the principal components and types of nuclear reactors.
o Evaluate cycle efficiency and performance of a gas cooled reactor power plant Classify
different types of coupled vapor cycles and list the advantages of combined cycles power
plant
o List different types of fuels used in power plants and estimate their heating values
o List types, principles of operations, components and applications of steam turbines,
steam generators, condensers, feed water and circulating water systems.
o Estimate different efficiencies associated with such systems
o Define terms and factors associated with power plant economics. Calculate present
worth depreciation and cost of different types of power plants. Estimate the cost of
producing power per kW.
UNIT – 1 14 Hours
STEM POWER PLANT: Different types of fuels used for steam generation, Equipment for
burning coal in lump form, strokers, different types, Oil burners, Advantages of using pulverized
fuel, Equipment for preparation and burning of pulverized coal, unit system and bin system.
Pulverised fuel furnaces, cyclone furnace, coal and ashhanding, generation of steam using forced
circulation, high and supercritical pressures, A brief account of L. Mont Benson, Velox,
Schmidt, Loeffer and ramson steam generator
CHIMNEYS: Natural, forced, induced and balanced draft, Calculations involving height of
chimney to produce a given draft

Accessories for the steam generator such as super heaters, desuperheater, control of super
heaters, Economisers, Air pre-heaters and re- heaters.
COOLING TOWERS AND PONDS : Different types of towers.

DIESEL ENGINE PLANT- ENGINES FOR POWER GENERATION: Method of starting
diesel engines, Cooling and lubrication system for the diesel engine. Filters, centrifuges, Oil
heaters, and exhaust system, Layout of a diesel power plant.
UNIT -3 12 Hours.
GAS TURBINE POWER PLANT: Advantages and disadvantages of the gas turbine plant,
open and closed cycle turbine plants with the accessories
HYDRO-ELECTRIC PLANTS: Storage and pondage, flow duration and mass curves,
hydrographs, Low, medium and high held plants, pumped storage plants, penstock, water
hammer, surge tanks, gates and valves, power house, general layout. A broef description of
some of the important hydel installation in India.
UNIT -4 12 Hours.
NUCLEAR POWER PLANT: Principles of release of nuclear energy fusion and fission
reactions. Nuclear fuels used in the reactors. Multiplication and thermal utilization factors.
Elements of the nuclear reactor , Moderator, control rod, fuel rods, coolants. Brief description
of reactors of the following types – pressurized water reactor , boiling water reactor sodium
graphite reactor, Fast breeder reactor, Homogeneous graphite reactor and gas cooled reactor,
Radiation hazards, Shieldings, Radio active waste dis posal
UNIT -5 12 Hours.
CHOICE OF SITE: For power station, load estimation, load duration curve, load factor,
capacity factor, use factor, diversity factor, demand factor effect of variable of variable load an
power plant, selection of the number and size of units
ECONOMIC ANALYSIS OF POWER PLANT: Cost of energy production. Selectio of plant
and generating equipment, performance and operating characteristics of power plants, triffs for
electrical energy.

ESSENTIAL READING:
1. Power Plant Engineering, P.K.Nag. Tata Mc Graw Hill 2nd ed 2001,.
2. Power Plant Engineering., Morse F.T. Van Nstrand.1998
1. Water Power Engg., Edition 3, Barrows, TMH, New Delhi. 1998
2. Plant Engg. Hand Book, Stanier, McGraw Hill. 1998
3. Hydraulic Machines, Jagadish Lal, Metropollitan Co 1996.
4. Principles of Energy Conversion, A.W.Culp Jr., McGraw Hill. 1996
5. Power Plant Technology, M.M. El-Wakil, McGraw Hill. International. 1994
6. Power Station Engg. Economics, Skrotizke and Vopat. 1994
7. Power Plant Engineering Domakundawar, Dhanpath Rai sons.2003.

ME833 NANOTECHNOLOGY
OBJECTIVE:
- Understand what nanotechnology is about and how to use it.
- Gain knowledge of
o structure, properties, manufacturing, and applications of silicon and carbon
materials.
o fabrication methods in nanotechnology (top down & bottom up)
o characterization methods in nanotechnology (optical, electrical, AFM, SEM, TEM,
and nanoindentation)
UNIT - 1
AN OVERVIEW OF NANOSCIENCE & NANOTECHNOLOGY – historical background –
nature, scope and content of the subject – multidisciplinary aspects – industrial, economic and
societal implications.
EXPERIMENTAL TECHNIQUES AND METHODS for investigating and manipulating
materials in the nano scale – electron microscope – scanning probe microscope – optical and
other microscopes – light scattering – x-ray diffraction.
FULLERENES – discovery, synthesis and purification – chemistry of fullerenes in the
condensed phase – orientational ordering – pressure effects – conductivity and superconductivity
– ferromagnetism – optical properties.
Carbon Nanotubes – synthesis and purification – filling of nanotubes – mechanism of growth –
electronic structure – transport properties – mechanical and physical properties – applications.
SELF-ASSEMBLED MONOLAYERS – monolayers on gold – growth process – phase
transitions – patterning monolayers – mixed monolayers – applications.
GAS PHASE CLUSTERS – history of cluster science – formation and growth – detection and
analysis – type and properties of clusters – bonding in clusters.

SEMICONDUCTOR QUANTUM DOTS – synthesis – electronic structure of nanocrystals –

how quantum dots are studied – correlation of properties with size – uses.
MONOLAYER-PROTECTED METAL NANOPARTICLES – method of preparation–
characterization – functionalized metal nanoparticles – applications – superlattices.
CORE-SHELL NANOPARTICLES – types – characterization – properties – applications.
NANOSHELLS – types – characterization – properties – applications.
NANOBIOLOGY – interaction between biomolecules and nanoparticle surfaces – materials
used for synthesis of hybrid nano-bio assemblies – biological applications – nanoprobes for
analytical applications – nanobiotechnology – future perspectives. Nanosensors – what make
them possible – nanoscale organization for sensors – characterization – nanosensors based on
optical properties – nanosensors based on quantum size effects – electrochemical sensors –
sensors based on physical properties – nanobiosensors – sensors of the future.
NANOMEDICINES – approach to development – nanotechnology in diagnostic and therapeutic
applications.
ESSENTIAL READINGS:
1. NANO: The Essentials – Understanding Nanoscience and Nanotechnology; T Pradeep

(Professor, IIT Madras); Tata McGraw-Hill India (2007)
2. Nanotechnology: Richard Booker & Earl Boysen; Wiley (2005).

1. Introduction to Nanoscale Science and Technology [Series: Nanostructure Science and

Technology], Di Ventra, et al (Ed); Springer (2004)
2. Nanotechnology Demystified, Linda Williams & Wade Adams; McGraw-Hill (2007)
3. Introduction to Nanotechnology, Charles P Poole Jr, Frank J Owens, Wiley India Pvt.
Ltd., New Delhi, 2007.

ME833 ORGANISATIONAL BEHAVIOUR & PROFESSIONAL COMMUNICATION

OBJECTIVES:
o To gain a solid understanding of human behavior in the workplace from an
individual,group, and organizational perspective.
o To obtain frameworks and tools to effectively analyze and approach various
organizational situations.
o To integrate course materials with your own workplace experiences.
o To reflect upon your own beliefs, assumptions, andbehaviors with respect to
how individuals, groups, and organizations act in order to expand your options
of approaches and increase your own effectiveness.
INTRODUCTION: Definition of Organization Behaviour and Historical development,
Environmental context (Information Technology and Globalization, Diversity and Ethics, Design
and Cultural, Reward Systems).
THE INDIVIDUAL: Foundations of individual behaviour, individual differences. Ability.
Attitude, Aptitude, interests. Values.
LEARNING: Definition, Theories of Learning, Individual Decision Making, classical
conditioning, operant conditioning, social learning theory, continuous and intermittent
reinforcement.
PERCEPTION: Definition, Factors influencing perception, attribution theory, selective
perception, projection, stereotyping, Halo effect.
MOTIVATION: Maslow's Hierarchy of Needs theory, Mc-Gregor's theory X and Y,
Hertzberg's motivation Hygiene theory, David Mc-Clelland‟s three needs theory, Victor Vroom's
expectancy theory of motivation.

THE GROUPS: Definition and classification of groups, Factors affecting group formation,
stages of group development, Norms, Hawthorne studies, group processes, group tasks, group
decision making.
CONFLICT & STRESS MANAGEMENT: Definition of conflict, functional and
dysfunctional conflict, stages of conflict process. Sources of stress, fatigue and its impact on
productivity. Job satisfaction, job rotation, enrichment, job enlargement and reengineering work
process.
PRINCIPLES OF COMMUNICATION: Useful definitions, communication principles,
communication system, role of communication in management, barriers in communication, how
to overcome the barriers, rule of effective communication.
ESSENTIAL READINGS:
1. Organizational Behaviour, Stephen P Robbins, 9th Edition, Pearson Education

Publications, ISBN-81-7808-561-5 2002
2. Organizational Behaviour, Fred Luthans, 9th Edition, Mc Graw Hill International Edition,
ISBN-0-07-120412-12002
1. Organizational Behaviour, Hellriegel, Srocum and Woodman, Thompson Learning, 9th

Edition, Prentice Hall India, 2001
2. Organizational Behaviour, Aswathappa - Himalaya Publishers. 2001
3. Organizational Behaviour, VSP Rao and others, Konark Publishers.2002
4. Organizational Behaviour, (Human behaviour at work) 9th Edition, John Newstron/ Keith
Davis. 2002

ME833 AUTOMOTIVE ENGINEERING

OBJECTIVES:
o To prepare students for successful careers in automotive and ancillary industry that meet
the needs of Indian and multinational companies.

o To develop the ability among students to synthesized at and technical concepts for
application to automotive design.
o To provide opportunity for students to work as part of teams on multidisciplinary
projects.
o To provide students with a sound foundation in the mathematical, scientific and
engineering fundamentals necessary to formulate, solve and analyse engineering
problems and to prepare them for graduate studies.
o To promote student awarenesss of the life-long learning and to introduce the professional
ethics and codes of professional practice.
LEARNING OUT COME:
o Will be able to implement specific advanced and emerging manufacturing technologies in
modern industry.
etc.
UNIT - 1
ENGINE COMPONENTS AND COOLING & LUBRICATION SYSTEMS:
Spark Ignition (SI) & Compression Ignition (CI) engines, cylinder - arrangements and their
relatives merits, Liners, Piston, connecting rod, crankshaft, valves, valve actuating
mechanisms, valve and port timing diagrams, Types of combustion chambers for S.I.Engine and
C.I.Engines, Compression ratio, methods of a Swirl generation, choice of materials for different
engine components, engine positioning, cooling requirements, methods of cooling,

thermostat valves, different lubrication arrangements.
FUELS, FUEL SUPPLY SYSTEMS FOR SI AND CI ENGINES: Conventional fuels,
alternative fuels, normal and abnormal combustion, cetane and octane numbers, Fuel
mixture requirements for SI engines, types of carburetors, C.D.& C.C. carburetors, multi
point and single point fuel injection systems, fuel transfer pumps, Fuel filters, fuel injection
pumps and injectors.
UNIT - 2
SUPERCHARGERS AND TURBOCHARGERS:

Naturally aspirated engines, Forced Induction, Types of superchargers, Turbocharger
construction and operation, Intercooler, Turbocharger
IGNITION SYSTEMS: Battery Ignition systems, magneto Ignition system, Transistor assist
contacts. Electronic Ignition, Automatic Ignition advance systems.
UNIT - 3
POWER TRAINS: General arrangement of clutch, Principle of friction clutches, Torque
transmitted, Constructional details, Fluid flywheel, Single plate, multi-plate and centrifugal
clutches. Gear box: Necessity for gear ratios in transmission, synchromesh gear boxes, 3, 4
and 5 speed gear boxes. Free wheeling mechanism, planetary gears systems, over drives, fluid
coupling and torque converters, Epicyclic gear box, principle of automatic transmission,
calculation of gear ratios, Numerical calculations for torque transmission by clutches.
UNIT - 4
DRIVE TO WHEELS: Propeller shaft and universal joints, Hotchkiss and torque tube drives,
differential, rear axle, different arrangements of fixing the wheels to rear axle, steering
geometry, camber, king pin inclination, included angle, castor, toe in & toe out, condition for
exact steering, steering gears, power steering, general arrangements of links and stub axle, over
steer, under steer and neutral steer, numerical problems, types of chassis frames.
SUSPENSION, SPRINGS AND BRAKES:
Requirements, Torsion bar suspension systems, leaf spring, coil spring, independent suspension
for front wheel and rear wheel. Air suspension system. Types of brakes, mechanical
compressed air, vacuum and hydraulic braking systems, construction and working of
master and wheel cylinder, brake shoe arrangements, Disk brakes, drum brakes, Antilock -
Braking systems, purpose and operation of antilock-braking system, ABS Hydraulic Unit,
Rear-wheel antilock & Numerical Problems.

UNIT - 5
AUTOMOTIVE EMISSION CONTROL SYSTEMS: Automotive emission controls,
Controlling crankcase emissions, Controlling evaporative emissions, Cleaning the exhaust gas,
Controlling the air-fuel mixture, Controlling the combustion process, Exhaust gas
recirculation, Treating the exhaust gas, Air-injection system, Air-aspirator system, Catalytic
converter, Emission standards- Euro I, II, III and IV norms, Bharat Stage II, III norms.
ESSENTIAL READINGS:
1. Automotive mechanics, William H Crouse & Donald L Anglin, 10 th Edition
Tata McGraw Hill Publishing Company Ltd., 2007

2. Automotive Mechanics, S. Srinivasan, Tata McGraw Hill 2003.
1. Automotive mechanics: Principles and Practices, Joseph Heitner, D Van
Nostrand Company, Inc
2. Fundamentals of Automobile Engineering,K .K.Ramalingam, Scitech Publications (India) Pvt.
Ltd.
3. Automobile Engineering, R. B. Gupta, Satya Prakashan, 4th edn. 1984.
4. Automobile engineering, Kirpal Singh. Vol I and II 2002.

BTCY01 CYBER SECURITY
AIM
This course is aimed at providing a comprehensive overview of the different facets of Cyber
Security. In addition, the course will detail into specifics of Cyber Security with Cyber Laws
both in Global and Indian Legal environments.
OBJECTIVES
Providing knowledge about different Cyber Crimes, Threats and Laws .Creating awareness about
risk management and protection from the cyber threats.
UNIT I
Security Fundamentals-4 As Architecture Authentication Authorization Accountability, Social
Media, Social Networking and Cyber Security.
Cyber Laws, IT Act 2000-IT Act 2008-Laws for Cyber-Security, Comprehensive National
Cyber-Security Initiative CNCI – Legalities.
UNIT II
Cyber Attack and Cyber Services
Computer Virus – Computer Worms – Trojan horse.
Vulnerabilities - Phishing - Online Attacks – Pharming - Phoarging – Cyber Attacks - Cyber
Threats - Zombie- stuxnet - Denial of Service Vulnerabilities - Server Hardening-TCP/IP
attack-SYN Flood.
UNIT III
Cyber Security Management
Risk Management and Assessment - Risk Management Process - Threat Determination Process -
Risk Assessment - Risk Management Lifecycle.
Security Policy Management - Security Policies - Coverage Matrix
Business Continuity Planning - DisasterTypes - Disaster Recovery Plan - Business Continuity
Planning Process.

UNIT-IV
Vulnerability - Assessment and Tools: Vulnerability Testing - Penetration Testing Black box-
white box.
Architectural Integration: Security Zones - Devicesviz Routers, Firewalls, DMZ.
Configuration Management - Certification and Accreditation for Cyber-Security.
UNIT V
Authentication and Cryptography: Authentication - Cryptosystems - Certificate Services
Securing Communications: Securing Services - Transport – Wireless - Steganography and
NTFS D ata Streams.

Intrusion Detection and Prevention Systems: Intrusion - Defense in Depth - IDS/IPS -IDS/IPS
Weakness and Forensic Analysis
Cyber Evolution: Cyber Organization - Cyber Future
RECOMMENDED READING
1. Matt Bishop, Introduction to Computer Security, Pearson, 6th impression, ISBN: 978-81-
7758-425-7.
2. Thomas R, Justin Peltier, John, Information Security Fundamentals, Auerbach Publications.
3. AtulKahate, Cryptography and Network Security 2nd Edition, Tata McGrawHill.
4. Nina Godbole, SunitBelapure, Cyber Security, Wiley India 1st Edition 2011.
5. Jennifer L. Bayuk and Jason Healey and Paul Rohmeyer and Marcus Sachs, Cyber Security
Policy Guidebook, Wiley; 1 edition , 2012, ISBN-10: 1118027809
6. Dan Shoemaker and Wm. Arthur Conklin, Cybersecurity: The Essential Body Of
Knowledge, Delmar Cengage Learning; 1 edition (May 17, 2011) ,ISBN-10: 1435481690
7. Stallings, “Cryptography & Network Security - Principles & Practice”, Prentice Hall, 3rd
Edition 2002.

Btech Mech

Uploaded by

Copyright:

Available Formats

Btech Mech

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Btech Mech

Uploaded by

Copyright:

Available Formats

B.Tech Course Structure and Syllabus for the year 2011, 2012.

2013 and 2014

COURSE STRUCTURE AND SYLLABUS

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 1

5 Admission Process 7-8

7 Grading Scheme for Each Paper: Undergraduate Courses 8

11 Teaching Pedagogy 10-11

13 Question Paper Pattern 12

15 Detailed Syllabus 17-230

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 2

Christ University was formerly Christ College (Autonomous) affiliated to Bangalore

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 3

"Christ University is a nurturing ground for an individuals holistic development to make

Department of Mechanical Engineering

The values which guide us at Christ University are:

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 4

02. COURSE OFFERED

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 5

03. ELIGIBLITY CRITERIA

 For Postgraduate Programmes:

o For Master of Technology in Computer Science & Engineering

 For Doctoral Programmes (Ph.D.):

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 6

04. SELECTION PROCESS

Process Particulars Date Venue/Centre

05. ADMISSION PROCESS

Candidates will be intimated about the Selection status (Selected/Wait Listed/Not

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 7

06. GENERAL RULES

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 8

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 9

07. Grading scheme for Each Paper: Undergraduate Courses

08. Grading scheme for Each Paper: Postgraduate Courses

Percentage Grade Grade Point Interpretation Class

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 10

DETAILS OF CIA (Continuous Internal Assessment):

CIA II : Assignments : 10 marks

For subjects having practical as part of the subject

09. COURSE OVERVIEW

10. COURSE OBJECTIVE

1. Join a technically sophisticated workforce as successful, practicing engineers in a wide

11. TEACHING PEDAGOGY

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 12

12. ASSESSMENT RULES

 Assessment of Project Work

o Continuous Internal Assessment:100 Marks

 Presentation assessed by Panel Members

 Assessment by the guide

o End Semester Examination:100 Marks

13. BRIEF OF PHYSICS AND CHEMISTRY CYCLE:

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 13

14. QUESTION PAPER PATTERN:

End Semester Examination (ESE) :

The ESE is conducted for 100 marks of 3 hours duration.

Question paper pattern is as follows.

Laboratory / Practical Papers:

Mid Semester Examination (MSE) :

Laboratory / Practical Papers:

The MSE is conducted for 50 marks of 2 hours duration. Writing,

Department of Mechanical Engineering- Christ University Faculty of Engineering Page 14