Distributed by:

www.Jameco.com ✦ 1-800-831-4242
The content and copyrights of the attached
material are the property of its owner.

Jameco Part Number 838591

 LM337L 3-Terminal Adjustable Regulator
June 2005

LM337L
3-Terminal Adjustable Regulator
General Description a fixed resistor between the adjustment and output, the
LM337L can be used as a precision current regulator. Sup-
The LM337L is an adjustable 3-terminal negative voltage plies with electronic shutdown can be achieved by clamping
regulator capable of supplying 100mA over a 1.2V to 37V the adjustment terminal to ground which programs the out-
output range. It is exceptionally easy to use and requires put to 1.2V where most loads draw little current.
only two external resistors to set the output voltage. Further-
The LM337L is available in a standard TO-92 transistor
more, both line and load regulation are better than standard
package, SO-8 surface mount package, and in our new 12
fixed regulators. Also, the LM337L is packaged in a standard
mil diameter bump micro SMD package. The LM337L is
TO-92 transistor package which is easy to use.
rated for operation over a −25˚C to +125˚C range.
In addition to higher performance than fixed regulators, the
For applications requiring greater output current in excess of
LM337L offers full overload protection. Included on the chip
0.5A and 1.5A, see LM137 series data sheets. For the
are current limit, thermal overload protection and safe area
positive complement, see series LM117 and LM317L data
protection. All overload protection circuitry remains fully func-
sheets.
tional even if the adjustment terminal is disconnected.
Normally, only a single 1µF solid tantalum output capacitor is
needed unless the device is situated more than 6 inches
Features
from the input filter capacitors, in which case an input bypass n Adjustable output down to 1.2V
is needed. A larger output capacitor can be added to improve n Guaranteed 100mA output current
transient response. The adjustment terminal can be by- n Line regulation typically 0.01%/V
passed to achieve very high ripple rejection ratios which are n Load regulation typically 0.1%
difficult to achieve with standard 3-terminal regulators. n Current limit constant with temperature
Besides replacing fixed regulators, the LM337L is useful in a n Eliminates the need to stock many voltages
wide variety of other applications. Since the regulator is n Standard 3-lead transistor package
“floating” and sees only the input-to-output differential volt- n 80 dB ripple rejection
age, supplies of several hundred volts can be regulated as
n Output is short circuit protected
long as the maximum input-to-output differential is not ex-
ceeded. n Available in the 6-Bump micro SMD package
n See AN-1112 for micro SMD considerations
Also, it makes an especially simple adjustable switching
regulator, a programmable output regulator, or by connecting

Typical Application
1.2V-25V Adjustable Regulator

00913403

© 2005 National Semiconductor Corporation DS009134 www.national.com

LM337L
Connection Diagrams
3-Pin TO92 8-Pin SOIC

00913401
Bottom View 00913402
Top View

6-Bump micro SMD micro SMD Laser mark

00913407

00913408

Ordering Information
Package Part Number Package Marking Transport Media NSC Drawing
3-Pin TO92 LM337LZ LM337LZ 1800 per Bag Z03A
LM337LM LM337LM Rails
8-Pin SOIC M08A
LM337LMX 2.5k Units Tape and Reel
LM337LBL 250 Units Tape and Reel
6-Bump micro SMD PA BLA06FNB
LM337LBLX 3k Units Tape and Reel

www.national.com 2
 LM337L
Absolute Maximum Ratings (Note 1) Storage Temperature −55˚C to +150˚C
If Military/Aerospace specified devices are required, Lead Temperature
please contact the National Semiconductor Sales Office/ (Soldering, 10 sec.) 300˚C
Distributors for availability and specifications. Plastic Package (Soldering 4 sec.) 260˚C
Power Dissipation Internally Limited ESD Rating 1.5kV (Note 5)
Input–Output Voltage Differential 40V
Operating Junction
Temperature Range −25˚C to +125˚C

Electrical Characteristics (Note 2)

Parameter Conditions Min Typ Max Units
Line Regulation TA = 25˚C, 3V ≤ |VIN − VOUT| ≤ 40V, 0.01 0.04 %/V
(Note 3)
Load Regulation TA = 25˚C, 5mA ≤ IOUT ≤ IMAX, (Note 3) 0.1 0.5 %
Thermal Regulation TA = 25˚C, 10ms Pulse 0.04 0.2 %/W
Adjustment Pin Current 50 100 µA
Adjustment Pin Current Change 5mA ≤ IL ≤ 100mA 0.2 5 µA
3V ≤ |VIN − VOUT| ≤ 40V
Reference Voltage 3V ≤ |VIN − VOUT| ≤ 40V, (Note 4) 1.20 1.25 1.30 V
10mA ≤ IOUT ≤ 100mA, P ≤ 625mW
Line Regulation 3V ≤ |VIN − VOUT| ≤ 40V, (Note 3) 0.02 0.07 %/V
Load Regulation 5mA ≤ IOUT ≤ 100mA, (Note 3) 0.3 1.5 %
Temperature Stability TMIN ≤ Tj ≤ TMAX 0.65 %
Minimum Load Current |VIN − VOUT| ≤ 40V 3.5 5 mA
3V ≤ |VIN − VOUT| ≤ 15V 2.2 3.5 mA
Current Limit 3V ≤ |VIN − VOUT| ≤ 13V 100 200 320 mA
|VIN − VOUT| = 40V 25 50 120 mA
Rms Output Noise, % of VOUT TA = 25˚C, 10Hz ≤ f ≤ 10kHz 0.003 %
Ripple Rejection Ratio VOUT = −10V, F = 120 Hz, CADJ = 0 65 dB
CADJ = 10µF 66 80 dB
Long-Term Stability TA = 125˚C 0.3 1 %

Note 1: “Absolute Maximum Ratings” indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
functional, but do not guarantee specific performance limits.
Note 2: Unless otherwise specified, these specifications apply −25˚C ≤ TJ ≤ + 125˚C for the LM337L; |VIN − VOUT| = 5V and IOUT = 40mA. Although power
dissipation is internally limited, these specifications are applicable for power dissipations up to 625 mW. IMAX is 100mA.
Note 3: Regulation is measured at constant junction temperature, using pulse testing with a low duty cycle. Changes in output voltage due to heating effects are
covered under the specification for thermal regulation.
Note 4: Thermal resistance of the TO-92 package is 180˚C/W junction to ambient with 0.4" leads from a PC board and 160˚C/W junction to ambient with 0.125" lead
length to PC board. The M package θJA is 180˚C/W in still air. The 6-Bump micro SMD package θJA is 290˚C/W in still air.
Note 5: Human body model, 1.5kΩ in series with 100pF.

3 www.national.com
LM337L
Typical Applications Regulator with Trimmable Output Voltage
1.2V-25V Adjustable Regulator

00913403
Full output current not available at high input-output voltages 00913404
Trim Procedure:
— If VOUT is −23.08V or bigger, cut out R3 (if smaller, don’t cut it out).
— Then if VOUT is −22.47V or bigger, cut out R4 (if smaller, don’t).
— Then if VOUT is −22.16V or bigger, cut out R5 (if smaller, don’t).
†C1 = 1µF solid tantalum or 10µF aluminum electrolytic required for
This will trim the output to well within 1% of −22.00 VDC, without any of the
stability
expense or trouble of a trim pot (see LB-46). Of course, this technique can
*C2 = 1µF solid tantalum is required only if regulator is more than 4" from be used at any output voltage level.
power supply filter capacitor

www.national.com 4
 LM337L
Physical Dimensions inches (millimeters)
unless otherwise noted

8-Pin SOIC
NS Package Number M08A

3-Pin TO-92 (Z)

NS Package Number Z03A

5 www.national.com
LM337L 3-Terminal Adjustable Regulator
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

NOTES: UNLESS OTHERWISE SPECIFIED

1. EPOXY COATING.
2. 63Sn/37Pb EUTECTIC BUMP.
3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD.
4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION. REMAINING PINS ARE NUMBERED
COUNTERCLOCKWISE.
5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH. X2 IS PACKAGE LENGTH AND X3 IS
PACKAGE HEIGHT (SEE TABLE, SHEET 2). EXAMPLE: BLA06AFA HAS WIDTH = 1006. LENGTH = 1641, HEIGHT = 795.
6. REFERENCE JEDEC REGISTRATION MO-211, VARIATION BC.
6-Bump micro SMD
NS Package Number BLA06FNB
X1 = 1133µm X2 = 1819µm X3 = 945µm

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves
the right at any time without notice to change said circuitry and specifications.
For the most current product information visit us at www.national.com.

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS
WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR
CORPORATION. As used herein:
1. Life support devices or systems are devices or systems 2. A critical component is any component of a life support
which, (a) are intended for surgical implant into the body, or device or system whose failure to perform can be reasonably
(b) support or sustain life, and whose failure to perform when expected to cause the failure of the life support device or
properly used in accordance with instructions for use system, or to affect its safety or effectiveness.
provided in the labeling, can be reasonably expected to result
in a significant injury to the user.
BANNED SUBSTANCE COMPLIANCE
National Semiconductor manufactures products and uses packing materials that meet the provisions of the Customer Products
Stewardship Specification (CSP-9-111C2) and the Banned Substances and Materials of Interest Specification (CSP-9-111S2) and contain
no ‘‘Banned Substances’’ as defined in CSP-9-111S2.
Leadfree products are RoHS compliant.

National Semiconductor National Semiconductor National Semiconductor National Semiconductor

Americas Customer Europe Customer Support Center Asia Pacific Customer Japan Customer Support Center
Support Center Fax: +49 (0) 180-530 85 86 Support Center Fax: 81-3-5639-7507
Email: new.feedback@nsc.com Email: europe.support@nsc.com Email: ap.support@nsc.com Email: jpn.feedback@nsc.com
Tel: 1-800-272-9959 Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
LM337L 3-Terminal Adjustable Regulator

Tel: 81-3-5639-7560
www.national.com