with Features

LM2672 SIMPLE SWITCHER Power Converter High Efficiency 1A Step-Down Voltage Regulator
May 2001

LM2672
SIMPLE SWITCHER ® Power Converter High Efficiency
1A Step-Down Voltage Regulator with Features
General Description To simplify the LM2672 buck regulator design procedure,
there exists computer design software, LM267X Made
The LM2672 series of regulators are monolithic integrated Simple version 6.0.
circuits built with a LMDMOS process. These regulators
provide all the active functions for a step-down (buck)
switching regulator, capable of driving a 1A load current with Features
excellent line and load regulation. These devices are avail- n Efficiency up to 96%
able in fixed output voltages of 3.3V, 5.0V, 12V, and an n Available in SO-8, 8-pin DIP and LLP packages
adjustable output version. n Computer Design Software LM267X Made Simple
Requiring a minimum number of external components, these version 6.0
regulators are simple to use and include patented internal n Simple and easy to design with
frequency compensation (Patent Nos. 5,382,918 and n Requires only 5 external components
5,514,947), fixed frequency oscillator, external shutdown, n Uses readily available standard inductors
soft-start, and frequency synchronization. n 3.3V, 5.0V, 12V, and adjustable output versions
The LM2672 series operates at a switching frequency of n Adjustable version output voltage range: 1.21V to 37V
260 kHz, thus allowing smaller sized filter components than n ± 1.5% max output voltage tolerance over line and load
what would be needed with lower frequency switching regu- conditions
lators. Because of its very high efficiency ( > 90%), the cop-
n Guaranteed 1A output load current
per traces on the printed circuit board are the only heat
n 0.25Ω DMOS Output Switch
sinking needed.
n Wide input voltage range: 8V to 40V
A family of standard inductors for use with the LM2672 are
n 260 kHz fixed frequency internal oscillator
available from several different manufacturers. This feature
greatly simplifies the design of switch-mode power supplies n TTL shutdown capability, low power standby mode
using these advanced ICs. Also included in the datasheet n Soft-start and frequency synchronization
are selector guides for diodes and capacitors designed to n Thermal shutdown and current limit protection
work in switch-mode power supplies.
Other features include a guaranteed ± 1.5% tolerance on Typical Applications
output voltage within specified input voltages and output n Simple High Efficiency ( > 90%) Step-Down (Buck)
load conditions, and ± 10% on the oscillator frequency. Ex- Regulator
ternal shutdown is included, featuring typically 50 µA n Efficient Pre-Regulator for Linear Regulators
stand-by current. The output switch includes current limiting,
as well as thermal shutdown for full protection under fault
conditions.

Typical Application (Fixed Output Voltage

Versions)

01293401

SIMPLE SWITCHER ® is a registered trademark of National Semiconductor Corporation.

Windows ® is a registered trademark of Microsoft Corporation.

© 2001 National Semiconductor Corporation DS012934 www.national.com

LM2672
Connection Diagrams
16-Lead LLP Surface Mount Package 8-Lead Package
Top View Top View

01293402
SO-8/DIP Package
See NSC Package Drawing Number MO8A/N08E

01293441
LLP Package
See NSC Package Drawing Number LDA16A

TABLE 1. Package Marking and Ordering Information

Output Voltage Order Information Package Marking Supplied as:
16 Lead LLP
12 LM2672LD-12 S0001B 1000 Units on Tape and Reel
12 LM2672LDX-12 S0001B 4500 Units on Tape and Reel
3.3 LM2672LD-3.3 S0002B 1000 Units on Tape and Reel
3.3 LM2672LDX-3.3 S0002B 4500 Units on Tape and Reel
5.0 LM2672LD-5.0 S0003B 1000 Units on Tape and Reel
5.0 LM2672LDX-5.0 S0003B 4500 Units on Tape and Reel
ADJ LM2672LD-ADJ S0004B 1000 Units on Tape and Reel
ADJ LM2672LDX-ADJ S0004B 4500 Units on Tape and Reel
SO-8
12 LM2672M-12 2672M-12 Shipped in Anti-Static Rails
12 LM2672MX-12 2672M-12 2500 Units on Tape and Reel
3.3 LM2672M-3.3 2672M-3.3 Shipped in Anti-Static Rails
3.3 LM2672MX-3.3 2672M-3.3 2500 Units on Tape and Reel
5.0 LM2672M-5.0 2672M-5.0 Shipped in Anti-Static Rails
5.0 LM2672MX-5.0 2672M-5.0 2500 Units on Tape and Reel
ADJ LM2672M-ADJ 2672M-ADJ Shipped in Anti-Static Rails
ADJ LM2672MX-ADJ 2672M-ADJ 2500 Units on Tape and Reel
DIP
12 LM2672N-12 LM2672N-12 Shipped in Anti-Static Rails
3.3 LM2672N-3.3 LM2672N-3.3 Shipped in Anti-Static Rails
5.0 LM2672N-5.0 LM2672N-5.0 Shipped in Anti-Static Rails
ADJ LM2672N-ADJ LM2672N-ADJ Shipped in Anti-Static Rails

www.national.com 2
 LM2672
Absolute Maximum Ratings (Note 1) Lead Temperature
If Military/Aerospace specified devices are required, M Package
please contact the National Semiconductor Sales Office/ Vapor Phase (60s) +215˚C
Distributors for availability and specifications.
Infrared (15s) +220˚C
Supply Voltage 45V N Package (Soldering, 10s) +260˚C
ON/OFF Pin Voltage −0.1V ≤ VSH ≤ 6V LLP Package (see AN-1187)
Switch Voltage to Ground −1V Maximum Junction Temperature +150˚C
Boost Pin Voltage VSW + 8V
Feedback Pin Voltage −0.3V ≤ VFB ≤ 14V
Operating Ratings
ESD Susceptibility
Human Body Model (Note 2) 2 kV Supply Voltage 6.5V to 40V

Power Dissipation Internally Limited Temperature Range −40˚C ≤ TJ ≤ +125˚C

Storage Temperature Range −65˚C to +150˚C

Electrical Characteristics
LM2672-3.3 Specifications with standard type face are for TJ = 25˚C, and those in bold type face apply over full
Operating Temperature Range.

Symbol Parameter Conditions Typical Min Max Units

(Note 4) (Note 5) (Note 5)
SYSTEM PARAMETERS Test Circuit Figure 2 (Note 3)
VOUT Output Voltage VIN = 8V to 40V, ILOAD = 20 mA to 1A 3.3 3.251/3.201 3.350/3.399 V
VOUT Output Voltage VIN = 6.5V to 40V, ILOAD = 20 mA to 500 mA 3.3 3.251/3.201 3.350/3.399 V
η Efficiency VIN = 12V, ILOAD = 1A 86 %

LM2672-5.0
Symbol Parameter Conditions Typical Min Max Units
(Note 4) (Note 5) (Note 5)
SYSTEM PARAMETERS Test Circuit Figure 2 (Note 3)
VOUT Output Voltage VIN = 8V to 40V, ILOAD = 20 mA to 1A 5.0 4.925/4.850 5.075/5.150 V
VOUT Output Voltage VIN = 6.5V to 40V, ILOAD = 20 mA to 500 mA 5.0 4.925/4.850 5.075/5.150 V
η Efficiency VIN = 12V, ILOAD = 1A 90 %

LM2672-12
Symbol Parameter Conditions Typical Min Max Units
(Note 4) (Note 5) (Note 5)
SYSTEM PARAMETERS Test Circuit Figure 2 (Note 3)
VOUT Output Voltage VIN = 15V to 40V, ILOAD = 20 mA to 1A 12 11.82/11.64 12.18/12.36 V
η Efficiency VIN = 24V, ILOAD = 1A 94 %

LM2672-ADJ
Symbol Parameter Conditions Typ Min Max Units
(Note 4) (Note 5) (Note 5)
SYSTEM PARAMETERS Test Circuit Figure 3 (Note 3)
VFB Feedback VIN = 8V to 40V, ILOAD = 20 mA to 1A
1.210 1.192/1.174 1.228/1.246 V
Voltage
VOUT Programmed for 5V
(see Circuit of Figure 3)

3 www.national.com
LM2672
LM2672-ADJ (Continued)

Symbol Parameter Conditions Typ Min Max Units

(Note 4) (Note 5) (Note 5)
VFB Feedback VIN = 6.5V to 40V, ILOAD = 20 mA to 500 mA
1.210 1.192/1.174 1.228/1.246 V
Voltage
VOUT Programmed for 5V
(see Circuit of Figure 3)
η Efficiency VIN = 12V, ILOAD = 1A 90 %

All Output Voltage Versions

Specifications with standard type face are for TJ = 25˚C, and those in bold type face apply over full Operating Temperature
Range. Unless otherwise specified, VIN = 12V for the 3.3V, 5V, and Adjustable versions and VIN = 24V for the 12V version,
and ILOAD = 100 mA.
Symbol Parameters Conditions Typ Min Max Units
DEVICE PARAMETERS
IQ Quiescent Current VFEEDBACK = 8V 2.5 3.6 mA
For 3.3V, 5.0V, and ADJ Versions
VFEEDBACK = 15V 2.5 mA
For 12V Versions
ISTBY Standby Quiescent Current ON/OFF Pin = 0V 50 100/150 µA
ICL Current Limit 1.55 1.25/1.2 2.1/2.2 A
IL Output Leakage Current VIN = 40V, ON/OFF Pin = 0V 1 25 µA
VSWITCH = 0V
VSWITCH = −1V, ON/OFF Pin = 0V 6 15 mA
RDS(ON) Switch On-Resistance ISWITCH = 1A 0.25 0.30/0.50 Ω
fO Oscillator Frequency Measured at Switch Pin 260 225 275 kHz
D Maximum Duty Cycle 95 %
Minimum Duty Cycle 0 %
IBIAS Feedback Bias VFEEDBACK = 1.3V 85 nA
Current ADJ Version Only
VS/D ON/OFF Pin 1.4 0.8 2.0 V
Voltage Thesholds
IS/D ON/OFF Pin Current ON/OFF Pin = 0V 20 7 37 µA
FSYNC Synchronization Frequency VSYNC = 3.5V, 50% duty cycle 400 kHz
VSYNC Synchronization Threshold
1.4 V
Voltage
VSS Soft-Start Voltage 0.63 0.53 0.73 V
ISS Soft-Start Current 4.5 1.5 6.9 µA
θJA Thermal Resistance N Package, Junction to Ambient (Note 6) 95 ˚C/W
M Package, Junction to Ambient (Note 6) 105

Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is
intended to be functional, but device parameter specifications may not be guaranteed under these conditions. For guaranteed specifications and test conditions, see
the Electrical Characteristics.
Note 2: The human body model is a 100 pF capacitor discharged through a 1.5 kΩ resistor into each pin.
Note 3: External components such as the catch diode, inductor, input and output capacitors, and voltage programming resistors can affect switching regulator
performance. When the LM2672 is used as shown in Figure 2 and Figure 3 test circuits, system performance will be as specified by the system parameters section
of the Electrical Characteristics.
Note 4: Typical numbers are at 25˚C and represent the most likely norm.
Note 5: All limits guaranteed at room temperature (standard type face) and at temperature extremes (bold type face). All room temperature limits are 100%
production tested. All limits at temperature extremes are guaranteed via correlation using standard Statistical Quality Control (SQC) methods. All limits are used
to calculate Average Outgoing Quality Level (AOQL).
Note 6: Junction to ambient thermal resistance with approximately 1 square inch of printed circuit board copper surrounding the leads. Additional copper area will
lower thermal resistance further. See Application Information section in the application note accompanying this datasheet and the thermal model in LM267X Made
Simple version 6.0 software. The value θJ−A for the LLP (LD) package is specifically dependent on PCB trace area, trace material, and the number of layers and
thermal vias. For improved thermal resistance and power dissipation for the LLP package, refer to Application Note AN-1187.

www.national.com 4
 LM2672
Typical Performance Characteristics
Normalized
Output Voltage Line Regulation Efficiency

01293403 01293404 01293405

Drain-to-Source Operating
Resistance Switch Current Limit Quiescent Current

01293406 01293407 01293408

Standby ON/OFF Threshold ON/OFF Pin

Quiescent Current Voltage Current (Sourcing)

01293409
01293410 01293411

Feedback Pin
Switching Frequency Bias Current Peak Switch Current

01293412 01293413 01293414

5 www.national.com
LM2672
Typical Performance Characteristics (Continued)

Dropout Voltage — 3.3V Option Dropout Voltage — 5.0V Option

01293415 01293416

Block Diagram

01293417
* Patent Number 5,514,947
† Patent Number 5,382,918

FIGURE 1.

www.national.com 6
 LM2672
Typical Performance
Characteristics (Circuit of Figure 2)
Continuous Mode Switching Waveforms Discontinuous Mode Switching Waveforms
VIN = 20V, VOUT = 5V, ILOAD = 1A VIN = 20V, VOUT = 5V, ILOAD = 300 mA
L = 47 µH, COUT = 68 µF, COUTESR = 50 mΩ L = 15 µH, COUT = 68 µF (2x), COUTESR = 25 mΩ

01293418 01293419
Horizontal Time Base: 1 µs/div Horizontal Time Base: 1 µs/div
A: VSW Pin Voltage, 10 V/div. A: VSW Pin Voltage, 10 V/div.
B: Inductor Current, 0.5 A/div B: Inductor Current, 0.5 A/div
C: Output Ripple Voltage, 20 mV/div AC-Coupled C: Output Ripple Voltage, 20 mV/div AC-Coupled

Load Transient Response for Continuous Mode Load Transient Response for Discontinuous Mode
VIN = 20V, VOUT = 5V, ILOAD = 1A VIN = 20V, VOUT = 5V,
L = 47 µH, COUT = 68 µF, COUTESR = 50 mΩ L = 47 µH, COUT = 68 µF, COUTESR = 50 mΩ

01293420 01293421
Horizontal Time Base: 50 µs/div Horizontal Time Base: 200 µs/div
A: Output Voltage, 100 mV/div, AC-Coupled A: Output Voltage, 100 mV/div, AC-Coupled
B: Load Current: 200 mA to 1A Load Pulse B: Load Current: 100 mA to 300 mA Load Pulse

7 www.national.com
LM2672
Test Circuit and Layout Guidelines

01293422
CIN - 22 µF, 50V Tantalum, Sprague “199D Series”
COUT - 47 µF, 25V Tantalum, Sprague “595D Series”
D1 - 3.3A, 50V Schottky Rectifier, IR 30WQ05F
L1 - 68 µH Sumida #RCR110D-680L
CB - 0.01 µF, 50V Ceramic

FIGURE 2. Standard Test Circuits and Layout Guides

Fixed Output Voltage Versions

01293423
CIN - 22 µF, 50V Tantalum, Sprague “199D Series”
COUT - 47 µF, 25V Tantalum, Sprague “595D Series”
D1 - 3.3A, 50V Schottky Rectifier, IR 30WQ05F
L1 - 68 µH Sumida #RCR110D-680L
R1 - 1.5 kΩ, 1%
CB - 0.01 µF, 50V Ceramic
For a 5V output, select R2 to be 4.75 kΩ, 1%

where VREF = 1.21V

Use a 1% resistor for best stability.

FIGURE 3. Standard Test Circuits and Layout Guides

Adjustable Output Voltage Versions

www.national.com 8
 LM2672
LM2672 Series Buck Regulator Design Procedure (Fixed Output)
PROCEDURE (Fixed Output Voltage Version) EXAMPLE (Fixed Output Voltage Version)
To simplify the buck regulator design procedure, National
Semiconductor is making available computer design software to
be used with the SIMPLE SWITCHER line of switching
regulators. LM267X Made Simple version 6.0 is available on
Windows ® 3.1, NT, or 95 operating systems.
Given: Given:
VOUT = Regulated Output Voltage (3.3V, 5V, or 12V) VOUT = 5V
VIN(max) = Maximum DC Input Voltage VIN(max) = 12V
ILOAD(max) = Maximum Load Current ILOAD(max) = 1A
1. Inductor Selection (L1) 1. Inductor Selection (L1)
A. Select the correct inductor value selection guide from Figure A. Use the inductor selection guide for the 5V version shown in
4 and Figure 5 or Figure 6 (output voltages of 3.3V, 5V, or 12V Figure 5.
respectively). For all other voltages, see the design procedure
for the adjustable version.
B. From the inductor value selection guide, identify the B. From the inductor value selection guide shown in Figure 5,
inductance region intersected by the Maximum Input Voltage the inductance region intersected by the 12V horizontal line and
line and the Maximum Load Current line. Each region is the 1A vertical line is 33 µH, and the inductor code is L23.
identified by an inductance value and an inductor code (LXX).
C. Select an appropriate inductor from the four manufacturer’s C. The inductance value required is 33 µH. From the table in
part numbers listed in Figure 8. Each manufacturer makes a Figure 8, go to the L23 line and choose an inductor part number
different style of inductor to allow flexibility in meeting various from any of the four manufacturers shown. (In most instances,
design requirements. Listed below are some of the both through hole and surface mount inductors are available.)
differentiating characteristics of each manufacturer’s inductors:
Schott: ferrite EP core inductors; these have very low leakage
magnetic fields to reduce electro-magnetic interference (EMI)
and are the lowest power loss inductors
Renco: ferrite stick core inductors; benefits are typically lowest
cost inductors and can withstand E • T and transient peak
currents above rated value. Be aware that these inductors have
an external magnetic field which may generate more EMI than
other types of inductors.
Pulse: powered iron toroid core inductors; these can also be low
cost and can withstand larger than normal E • T and transient
peak currents. Toroid inductors have low EMI.
Coilcraft: ferrite drum core inductors; these are the smallest
physical size inductors, available only as SMT components. Be
aware that these inductors also generate EMI — but less than
stick inductors.
Complete specifications for these inductors are available from
the respective manufacturers. A table listing the manufacturers’
phone numbers is located in Figure 9.
2. Output Capacitor Selection (COUT) 2. Output Capacitor Selection (COUT)
A. Select an output capacitor from the output capacitor table in A. Use the 5.0V section in the output capacitor table in Figure
Figure 10. Using the output voltage and the inductance value 10. Choose a capacitor value and voltage rating from the line
found in the inductor selection guide, step 1, locate the that contains the inductance value of 33 µH. The capacitance
appropriate capacitor value and voltage rating. and voltage rating values corresponding to the 33 µH

9 www.national.com
LM2672
LM2672 Series Buck Regulator Design Procedure (Fixed Output) (Continued)

PROCEDURE (Fixed Output Voltage Version) EXAMPLE (Fixed Output Voltage Version)
The capacitor list contains through-hole electrolytic capacitors Surface Mount:
from four different capacitor manufacturers and surface mount 68 µF/10V Sprague 594D Series.
tantalum capacitors from two different capacitor manufacturers. 100 µF/10V AVX TPS Series.
It is recommended that both the manufacturers and the Through Hole:
manufacturer’s series that are listed in the table be used. A 68 µF/10V Sanyo OS-CON SA Series.
table listing the manufacturers’ phone numbers is located in 220 µF/35V Sanyo MV-GX Series.
Figure 11. 220 µF/35V Nichicon PL Series.
220 µF/35V Panasonic HFQ Series.
3. Catch Diode Selection (D1) 3. Catch Diode Selection (D1)
A. In normal operation, the average current of the catch diode is A. Refer to the table shown in Figure 12. In this example, a 1A,
the load current times the catch diode duty cycle, 1-D (D is the 20V Schottky diode will provide the best performance. If the
switch duty cycle, which is approximately the output voltage circuit must withstand a continuous shorted output, a higher
divided by the input voltage). The largest value of the catch current Schottky diode is recommended.
diode average current occurs at the maximum load current and
maximum input voltage (minimum D). For normal operation, the
catch diode current rating must be at least 1.3 times greater
than its maximum average current. However, if the power supply
design must withstand a continuous output short, the diode
should have a current rating equal to the maximum current limit
of the LM2672. The most stressful condition for this diode is a
shorted output condition.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
C. Because of their fast switching speed and low forward
voltage drop, Schottky diodes provide the best performance and
efficiency. This Schottky diode must be located close to the
LM2672 using short leads and short printed circuit traces.

www.national.com 10
 LM2672
LM2672 Series Buck Regulator Design Procedure (Fixed Output) (Continued)

PROCEDURE (Fixed Output Voltage Version) EXAMPLE (Fixed Output Voltage Version)
4. Input Capacitor (CIN) 4. Input Capacitor (CIN)
A low ESR aluminum or tantalum bypass capacitor is needed The important parameters for the input capacitor are the input
between the input pin and ground to prevent large voltage voltage rating and the RMS current rating. With a maximum
transients from appearing at the input. This capacitor should be input voltage of 12V, an aluminum electrolytic capacitor with a
located close to the IC using short leads. In addition, the RMS voltage rating greater than 15V (1.25 x VIN) would be needed.
current rating of the input capacitor should be selected to be at The next higher capacitor voltage rating is 16V.
least 1⁄2 the DC load current. The capacitor manufacturer data The RMS current rating requirement for the input capacitor in a
sheet must be checked to assure that this current rating is not buck regulator is approximately 1⁄2 the DC load current. In this
exceeded. The curves shown in Figure 14 show typical RMS example, with a 1A load, a capacitor with a RMS current rating
current ratings for several different aluminum electrolytic of at least 500 mA is needed. The curves shown in Figure 14
capacitor values. A parallel connection of two or more can be used to select an appropriate input capacitor. From the
capacitors may be required to increase the total minimum RMS curves, locate the 16V line and note which capacitor values
current rating to suit the application requirements. have RMS current ratings greater than 500 mA.
For an aluminum electrolytic capacitor, the voltage rating should For a through hole design, a 330 µF/16V electrolytic capacitor
be at least 1.25 times the maximum input voltage. Caution must (Panasonic HFQ series, Nichicon PL, Sanyo MV-GX series or
be exercised if solid tantalum capacitors are used. The tantalum equivalent) would be adequate. Other types or other
capacitor voltage rating should be twice the maximum input manufacturers’ capacitors can be used provided the RMS ripple
voltage. The tables in Figure 15 show the recommended current ratings are adequate. Additionally, for a complete
application voltage for AVX TPS and Sprague 594D tantalum surface mount design, electrolytic capacitors such as the Sanyo
capacitors. It is also recommended that they be surge current CV-C or CV-BS and the Nichicon WF or UR and the NIC
tested by the manufacturer. The TPS series available from AVX, Components NACZ series could be considered.
and the 593D and 594D series from Sprague are all surge For surface mount designs, solid tantalum capacitors can be
current tested. Another approach to minimize the surge current used, but caution must be exercised with regard to the capacitor
stresses on the input capacitor is to add a small inductor in surge current rating and voltage rating. In this example,
series with the input supply line. checking Figure 15, and the Sprague 594D series datasheet, a
Use caution when using ceramic capacitors for input bypassing, Sprague 594D 15 µF, 25V capacitor is adequate.
because it may cause severe ringing at the VIN pin.
5. Boost Capacitor (CB) 5. Boost Capacitor (CB)
This capacitor develops the necessary voltage to turn the switch For this application, and all applications, use a 0.01 µF, 50V
gate on fully. All applications should use a 0.01 µF, 50V ceramic ceramic capacitor.
capacitor.
6. Soft-Start Capacitor (CSS - optional) 6. Soft-Start Capacitor (CSS - optional)
This capacitor controls the rate at which the device starts up. For this application, selecting a start-up time of 10 ms and using
The formula for the soft-start capacitor CSS is: the formula for CSS results in a value of:

where:
ISS = Soft-Start Current :4.5 µA typical.
tSS = Soft-Start Time :Selected.
VSSTH = Soft-Start Threshold Voltage :0.63V typical.
VOUT = Output Voltage :Selected.
VSCHOTTKY = Schottky Diode Voltage Drop :0.4V typical.
VIN = Input Voltage :Selected.
If this feature is not desired, leave this pin open.

11 www.national.com
LM2672
LM2672 Series Buck Regulator Design Procedure (Fixed Output) (Continued)

PROCEDURE (Fixed Output Voltage Version) EXAMPLE (Fixed Output Voltage Version)
7. Frequency Synchronization (optional) 7. Frequency Synchronization (optional)
The LM2672 (oscillator) can be synchronized to run with an For all applications, use a 1 kΩ resistor and a 100 pF capacitor
external oscillator, using the sync pin (pin 3). By doing so, the for the RC filter.
LM2672 can be operated at higher frequencies than the
standard frequency of 260 kHz. This allows for a reduction in
the size of the inductor and output capacitor.
As shown in the drawing below, a signal applied to a RC filter at
the sync pin causes the device to synchronize to the frequency
of that signal. For a signal with a peak-to-peak amplitude of 3V
or greater, a 1 kΩ resistor and a 100 pF capacitor are suitable
values.

www.national.com 12
 LM2672
INDUCTOR VALUE SELECTION GUIDES
(For Continuous Mode Operation)

01293429

01293431

FIGURE 4. LM2672-3.3
FIGURE 6. LM2672-12

01293430

01293432
FIGURE 5. LM2672-5.0
FIGURE 7. LM2672-ADJ

13 www.national.com
LM2672 Ind.
Inductance Current
Schott Renco Pulse Engineering Coilcraft
Ref. Through Surface Through Surface Through Surface Surface
(µH) (A)
Desg. Hole Mount Hole Mount Hole Mount Mount
L4 68 0.32 67143940 67144310 RL-1284-68-43 RL1500-68 PE-53804 PE-53804-S DO1608-683
L5 47 0.37 67148310 67148420 RL-1284-47-43 RL1500-47 PE-53805 PE-53805-S DO1608-473
L6 33 0.44 67148320 67148430 RL-1284-33-43 RL1500-33 PE-53806 PE-53806-S DO1608-333
L7 22 0.52 67148330 67148440 RL-1284-22-43 RL1500-22 PE-53807 PE-53807-S DO1608-223
L9 220 0.32 67143960 67144330 RL-5470-3 RL1500-220 PE-53809 PE-53809-S DO3308-224
L10 150 0.39 67143970 67144340 RL-5470-4 RL1500-150 PE-53810 PE-53810-S DO3308-154
L11 100 0.48 67143980 67144350 RL-5470-5 RL1500-100 PE-53811 PE-53811-S DO3308-104
L12 68 0.58 67143990 67144360 RL-5470-6 RL1500-68 PE-53812 PE-53812-S DO3308-683
L13 47 0.70 67144000 67144380 RL-5470-7 RL1500-47 PE-53813 PE-53813-S DO3308-473
L14 33 0.83 67148340 67148450 RL-1284-33-43 RL1500-33 PE-53814 PE-53814-S DO3308-333
L15 22 0.99 67148350 67148460 RL-1284-22-43 RL1500-22 PE-53815 PE-53815-S DO3308-223
L18 220 0.55 67144040 67144420 RL-5471-2 RL1500-220 PE-53818 PE-53818-S DO3316-224
L19 150 0.66 67144050 67144430 RL-5471-3 RL1500-150 PE-53819 PE-53819-S DO3316-154
L20 100 0.82 67144060 67144440 RL-5471-4 RL1500-100 PE-53820 PE-53820-S DO3316-104
L21 68 0.99 67144070 67144450 RL-5471-5 RL1500-68 PE-53821 PE-53821-S DO3316-683
L22 47 1.17 67144080 67144460 RL-5471-6 — PE-53822 PE-53822-S DO3316-473
L23 33 1.40 67144090 67144470 RL-5471-7 — PE-53823 PE-53823-S DO3316-333
L24 22 1.70 67148370 67148480 RL-1283-22-43 — PE-53824 PE-53824-S DO3316-223
L27 220 1.00 67144110 67144490 RL-5471-2 — PE-53827 PE-53827-S DO5022P-224
L28 150 1.20 67144120 67144500 RL-5471-3 — PE-53828 PE-53828-S DO5022P-154
L29 100 1.47 67144130 67144510 RL-5471-4 — PE-53829 PE-53829-S DO5022P-104
L30 68 1.78 67144140 67144520 RL-5471-5 — PE-53830 PE-53830-S DO5022P-683

FIGURE 8. Inductor Manufacturers’ Part Numbers

Coilcraft Inc. Phone (800) 322-2645

FAX (708) 639-1469
Coilcraft Inc., Europe Phone +44 1236 730 595
FAX +44 1236 730 627
Pulse Engineering Inc. Phone (619) 674-8100
FAX (619) 674-8262
Pulse Engineering Inc., Phone +353 93 24 107
Europe FAX +353 93 24 459
Renco Electronics Inc. Phone (800) 645-5828
FAX (516) 586-5562
Schott Corp. Phone (612) 475-1173
FAX (612) 475-1786

FIGURE 9. Inductor Manufacturers’ Phone Numbers

www.national.com 14
 LM2672
Output Capacitor
Output Surface Mount Through Hole
Inductance
Voltage Sprague AVX TPS Sanyo OS-CON Sanyo MV-GX Nichicon Panasonic
(µH)
(V) 594D Series Series SA Series Series PL Series HFQ Series
(µF/V) (µF/V) (µF/V) (µF/V) (µF/V) (µF/V)
22 120/6.3 100/10 100/10 330/35 330/35 330/35
33 120/6.3 100/10 68/10 220/35 220/35 220/35
47 68/10 100/10 68/10 150/35 150/35 150/35
3.3
68 120/6.3 100/10 100/10 120/35 120/35 120/35
100 120/6.3 100/10 100/10 120/35 120/35 120/35
150 120/6.3 100/10 100/10 120/35 120/35 120/35
22 100/16 100/10 100/10 330/35 330/35 330/35
33 68/10 10010 68/10 220/35 220/35 220/35
47 68/10 100/10 68/10 150/35 150/35 150/35
5.0
68 100/16 100/10 100/10 120/35 120/35 120/35
100 100/16 100/10 100/10 120/35 120/35 120/35
150 100/16 100/10 100/10 120/35 120/35 120/35
22 120/20 (2x) 68/20 68/20 330/35 330/35 330/35
33 68/25 68/20 68/20 220/35 220/35 220/35
47 47/20 68/20 47/20 150/35 150/35 150/35
12 68 47/20 68/20 47/20 120/35 120/35 120/35
100 47/20 68/20 47/20 120/35 120/35 120/35
150 47/20 68/20 47/20 120/35 120/35 120/35
220 47/20 68/20 47/20 120/35 120/35 120/35

FIGURE 10. Output Capacitor Table

Nichicon Corp. Phone (847) 843-7500

FAX (847) 843-2798
Panasonic Phone (714) 373-7857
FAX (714) 373-7102
AVX Corp. Phone (803) 448-9411
FAX (803) 448-1943
Sprague/Vishay Phone (207) 324-4140
FAX (207) 324-7223
Sanyo Corp. Phone (619) 661-6322
FAX (619) 661-1055

FIGURE 11. Capacitor Manufacturers’ Phone Numbers

15 www.national.com
LM2672 1A Diodes 3A Diodes
VR Surface Through Surface Through
Mount Hole Mount Hole
20V SK12 1N5817 SK32 1N5820
B120 SR102 SR302
30V SK13 1N5818 SK33 1N5821
B130 11DQ03 30WQ03F 31DQ03
MBRS130 SR103
40V SK14 1N5819 SK34 1N5822
B140 11DQ04 30BQ040 MBR340
MBRS140 SR104 30WQ04F 31DQ04
10BQ040 MBRS340 SR304
10MQ040 MBRD340
15MQ040
50V SK15 MBR150 SK35 MBR350
B150 11DQ05 30WQ05F 31DQ05
10BQ050 SR105 SR305

FIGURE 12. Schottky Diode Selection Table

International Rectifier Phone (310) 322-3331

Corp.
FAX (310) 322-3332
Motorola, Inc. Phone (800) 521-6274
FAX (602) 244-6609
General Instruments Phone (516) 847-3000
Corp.
FAX (516) 847-3236
Diodes, Inc. Phone (805) 446-4800
FAX (805) 446-4850

FIGURE 13. Diode Manufacturers’ Phone Numbers

01293433

FIGURE 14. RMS Current Ratings for Low ESR Electrolytic Capacitors (Typical)

www.national.com 16
 LM2672
AVX TPS
Recommended Voltage
Application Voltage Rating
+85˚C Rating
3.3 6.3
5 10
10 20
12 25
15 35

Sprague 594D
Recommended Voltage
Application Voltage Rating
+85˚C Rating
2.5 4
3.3 6.3
5 10
8 16
12 20
18 25
24 35
29 50

FIGURE 15. Recommended Application Voltage for AVX TPS and

Sprague 594D Tantalum Chip Capacitors Derated for 85˚C.

LM2672 Series Buck Regulator

Design Procedure (Adjustable
Output)
PROCEDURE (Adjustable Output Voltage Version) EXAMPLE (Adjustable Output Voltage Version)
To simplify the buck regulator design procedure, National
Semiconductor is making available computer design software to
be used with the SIMPLE SWITCHER line of switching
regulators. LM267X Made Simple version 6.0 is available on
Windows 3.1, NT, or 95 operating systems.
Given: Given:
VOUT = Regulated Output Voltage VOUT = 20V
VIN(max) = Maximum Input Voltage VIN(max) = 28V
ILOAD(max) = Maximum Load Current ILOAD(max) = 1A
F = Switching Frequency (Fixed at a nominal 260 kHz). F = Switching Frequency (Fixed at a nominal 260 kHz).
1. Programming Output Voltage (Selecting R1 and R2, as 1. Programming Output Voltage (Selecting R1 and R2, as
shown in Figure 3) shown in Figure 3)
Use the following formula to select the appropriate resistor Select R1 to be 1 kΩ, 1%. Solve for R2.
values.

where VREF = 1.21V

Select a value for R1 between 240Ω and 1.5 kΩ. The lower R2 = 1 kΩ (16.53 − 1) = 15.53 kΩ, closest 1% value is 15.4 kΩ.
resistor values minimize noise pickup in the sensitive feedback R2 = 15.4 kΩ.
pin. (For the lowest temperature coefficient and the best stability
with time, use 1% metal film resistors.)

17 www.national.com
LM2672
LM2672 Series Buck Regulator Design Procedure (Adjustable Output)
(Continued)

PROCEDURE (Adjustable Output Voltage Version) EXAMPLE (Adjustable Output Voltage Version)
2. Inductor Selection (L1) 2. Inductor Selection (L1)
A. Calculate the inductor Volt • microsecond constant E • T A. Calculate the inductor Volt • microsecond constant (E • T),
(V • µs), from the following formula:

where VSAT =internal switch saturation voltage=0.25V and

VD = diode forward voltage drop = 0.5V
B. Use the E • T value from the previous formula and match it B. E • T = 21.6 (V • µs)
with the E • T number on the vertical axis of the Inductor Value
Selection Guide shown in Figure 7.
C. On the horizontal axis, select the maximum load current. C. ILOAD(max) = 1A
D. Identify the inductance region intersected by the E • T value D. From the inductor value selection guide shown in Figure 7,
and the Maximum Load Current value. Each region is identified the inductance region intersected by the 21.6 (V • µs) horizontal
by an inductance value and an inductor code (LXX). line and the 1A vertical line is 68 µH, and the inductor code is
L30.
E. Select an appropriate inductor from the four manufacturer’s E. From the table in Figure 8, locate line L30, and select an
part numbers listed in Figure 8. For information on the different inductor part number from the list of manufacturers’ part
types of inductors, see the inductor selection in the fixed output numbers.
voltage design procedure.
3. Output Capacitor SeIection (COUT) 3. Output Capacitor SeIection (COUT)
A. Select an output capacitor from the capacitor code selection A. Use the appropriate row of the capacitor code selection
guide in Figure 16. Using the inductance value found in the guide, in Figure 16. For this example, use the 15–20V row. The
inductor selection guide, step 1, locate the appropriate capacitor capacitor code corresponding to an inductance of 68 µH is C20.
code corresponding to the desired output voltage.
B. Select an appropriate capacitor value and voltage rating, B. From the output capacitor selection table in Figure 17,
using the capacitor code, from the output capacitor selection choose a capacitor value (and voltage rating) that intersects the
table in Figure 17. There are two solid tantalum (surface mount) capacitor code(s) selected in section A, C20.
capacitor manufacturers and four electrolytic (through hole) The capacitance and voltage rating values corresponding to the
capacitor manufacturers to choose from. It is recommended that capacitor code C20 are the:
both the manufacturers and the manufacturer’s series that are Surface Mount:
listed in the table be used. A table listing the manufacturers’ 33 µF/25V Sprague 594D Series.
phone numbers is located in Figure 11. 33 µF/25V AVX TPS Series.
Through Hole:
33 µF/25V Sanyo OS-CON SC Series.
120 µF/35V Sanyo MV-GX Series.
120 µF/35V Nichicon PL Series.
120 µF/35V Panasonic HFQ Series.
Other manufacturers or other types of capacitors may also be
used, provided the capacitor specifications (especially the 100
kHz ESR) closely match the characteristics of the capacitors
listed in the output capacitor table. Refer to the capacitor
manufacturers’ data sheet for this information.

www.national.com 18
 LM2672
LM2672 Series Buck Regulator Design Procedure (Adjustable Output)
(Continued)

PROCEDURE (Adjustable Output Voltage Version) EXAMPLE (Adjustable Output Voltage Version)
4. Catch Diode Selection (D1) 4. Catch Diode Selection (D1)
A. In normal operation, the average current of the catch diode is A. Refer to the table shown in Figure 12. Schottky diodes
the load current times the catch diode duty cycle, 1-D (D is the provide the best performance, and in this example a 1A, 40V
switch duty cycle, which is approximately VOUT/VIN). The largest Schottky diode would be a good choice. If the circuit must
value of the catch diode average current occurs at the maximum withstand a continuous shorted output, a higher current (at least
input voltage (minimum D). For normal operation, the catch 2.2A) Schottky diode is recommended.
diode current rating must be at least 1.3 times greater than its
maximum average current. However, if the power supply design
must withstand a continuous output short, the diode should have
a current rating greater than the maximum current limit of the
LM2672. The most stressful condition for this diode is a shorted
output condition.
B. The reverse voltage rating of the diode should be at least
1.25 times the maximum input voltage.
C. Because of their fast switching speed and low forward
voltage drop, Schottky diodes provide the best performance and
efficiency. The Schottky diode must be located close to the
LM2672 using short leads and short printed circuit traces.
5. Input Capacitor (CIN) 5. Input Capacitor (CIN)
A low ESR aluminum or tantalum bypass capacitor is needed The important parameters for the input capacitor are the input
between the input pin and ground to prevent large voltage voltage rating and the RMS current rating. With a maximum
transients from appearing at the input. This capacitor should be input voltage of 28V, an aluminum electrolytic capacitor with a
located close to the IC using short leads. In addition, the RMS voltage rating of at least 35V (1.25 x VIN) would be needed.
current rating of the input capacitor should be selected to be at The RMS current rating requirement for the input capacitor in a
least 1⁄2 the DC load current. The capacitor manufacturer data buck regulator is approximately 1⁄2 the DC load current. In this
sheet must be checked to assure that this current rating is not example, with a 1A load, a capacitor with a RMS current rating
exceeded. The curves shown in Figure 14 show typical RMS of at least 500 mA is needed. The curves shown in Figure 14
current ratings for several different aluminum electrolytic can be used to select an appropriate input capacitor. From the
capacitor values. A parallel connection of two or more curves, locate the 35V line and note which capacitor values
capacitors may be required to increase the total minimum RMS have RMS current ratings greater than 500 mA.
current rating to suit the application requirements. For a through hole design, a 330 µF/35V electrolytic capacitor
For an aluminum electrolytic capacitor, the voltage rating should (Panasonic HFQ series, Nichicon PL, Sanyo MV-GX series or
be at least 1.25 times the maximum input voltage. Caution must equivalent) would be adequate. Other types or other
be exercised if solid tantalum capacitors are used. The tantalum manufacturers’ capacitors can be used provided the RMS ripple
capacitor voltage rating should be twice the maximum input current ratings are adequate. Additionally, for a complete
voltage. The tables in Figure 15 show the recommended surface mount design, electrolytic capacitors such as the Sanyo
application voltage for AVX TPS and Sprague 594D tantalum CV-C or CV-BS and the Nichicon WF or UR and the NIC
capacitors. It is also recommended that they be surge current Components NACZ series could be considered.
tested by the manufacturer. The TPS series available from AVX, For surface mount designs, solid tantalum capacitors can be
and the 593D and 594D series from Sprague are all surge used, but caution must be exercised with regard to the capacitor
current tested. Another approach to minimize the surge current surge current rating and voltage rating. In this example,
stresses on the input capacitor is to add a small inductor in checking Figure 15, and the Sprague 594D series datasheet, a
series with the input supply line. Sprague 594D 15 µF, 50V capacitor is adequate.
Use caution when using ceramic capacitors for input bypassing,
because it may cause severe ringing at the VIN pin.
6. Boost Capacitor (CB) 6. Boost Capacitor (CB)
This capacitor develops the necessary voltage to turn the switch For this application, and all applications, use a 0.01 µF, 50V
gate on fully. All applications should use a 0.01 µF, 50V ceramic ceramic capacitor.
capacitor.
If the soft-start and frequency synchronization features are
desired, look at steps 6 and 7 in the fixed output design
procedure.

19 www.national.com
LM2672
LM2672 Series Buck Regulator Design Procedure (Adjustable Output)
(Continued)

Case Output Inductance (µH)

Style (Note 7) Voltage (V) 22 33 47 68 100 150 220
SM and TH 1.21–2.50 — — — — C1 C2 C3
SM and TH 2.50–3.75 — — — C1 C2 C3 C3
SM and TH 3.75–5.0 — — C4 C5 C6 C6 C6
SM and TH 5.0–6.25 — C4 C7 C6 C6 C6 C6
SM and TH 6.25–7.5 C8 C4 C7 C6 C6 C6 C6
SM and TH 7.5–10.0 C9 C10 C11 C12 C13 C13 C13
SM and TH 10.0–12.5 C14 C11 C12 C12 C13 C13 C13
SM and TH 12.5–15.0 C15 C16 C17 C17 C17 C17 C17
SM and TH 15.0–20.0 C18 C19 C20 C20 C20 C20 C20
SM and TH 20.0–30.0 C21 C22 C22 C22 C22 C22 C22
TH 30.0–37.0 C23 C24 C24 C25 C25 C25 C25
Note 7: SM - Surface Mount, TH - Through Hole

FIGURE 16. Capacitor Code Selection Guide

Output Capacitor
Cap. Surface Mount Through Hole
Ref. Sprague AVX TPS Sanyo OS-CON Sanyo MV-GX Nichicon Panasonic
Desg. 594D Series Series SA Series Series PL Series HFQ Series
# (µF/V) (µF/V) (µF/V) (µF/V) (µF/V) (µF/V)
C1 120/6.3 100/10 100/10 220/35 220/35 220/35
C2 120/6.3 100/10 100/10 150/35 150/35 150/35
C3 120/6.3 100/10 100/35 120/35 120/35 120/35
C4 68/10 100/10 68/10 220/35 220/35 220/35
C5 100/16 100/10 100/10 150/35 150/35 150/35
C6 100/16 100/10 100/10 120/35 120/35 120/35
C7 68/10 100/10 68/10 150/35 150/35 150/35
C8 100/16 100/10 100/10 330/35 330/35 330/35
C9 100/16 100/16 100/16 330/35 330/35 330/35
C10 100/16 100/16 68/16 220/35 220/35 220/35
C11 100/16 100/16 68/16 150/35 150/35 150/35
C12 100/16 100/16 68/16 120/35 120/35 120/35
C13 100/16 100/16 100/16 120/35 120/35 120/35
C14 100/16 100/16 100/16 220/35 220/35 220/35
C15 47/20 68/20 47/20 220/35 220/35 220/35
C16 47/20 68/20 47/20 150/35 150/35 150/35
C17 47/20 68/20 47/20 120/35 120/35 120/35
C18 68/25 (2x) 33/25 47/25 (Note 8) 220/35 220/35 220/35
C19 33/25 33/25 33/25 (Note 8) 150/35 150/35 150/35
C20 33/25 33/25 33/25 (Note 8) 120/35 120/35 120/35
C21 33/35 (2x) 22/25 (Note 9) 150/35 150/35 150/35
C22 33/35 22/35 (Note 9) 120/35 120/35 120/35
C23 (Note 9) (Note 9) (Note 9) 220/50 100/50 120/50
C24 (Note 9) (Note 9) (Note 9) 150/50 100/50 120/50
C25 (Note 9) (Note 9) (Note 9) 150/50 82/50 82/50
Note 8: The SC series of Os-Con capacitors (others are SA series)
Note 9: The voltage ratings of the surface mount tantalum chip and Os-Con capacitors are too low to work at these voltages.

FIGURE 17. Output Capacitor Selection Table

www.national.com 20
 LM2672
Application Information
TYPICAL SURFACE MOUNT PC BOARD LAYOUT, FIXD OUTPUT (4X SIZE)

01293439
CIN - 15 µF, 50V, Solid Tantalum Sprague, “594D series”
COUT - 68 µF, 16V, Solid Tantalum Sprague, “594D series”
D1 - 1A, 40V Schottky Rectifier, Surface Mount
L1 - 33 µH, L23, Coilcraft DO3316
CB - 0.01 µF, 50V, Ceramic

TYPICAL SURFACE MOUNT PC BOARD LAYOUT, ADJUSTABLE OUTPUT (4X SIZE)

01293440
CIN - 15 µF, 50V, Solid Tantalum Sprague, “594D series”
COUT - 33 µF, 25V, Solid Tantalum Sprague, “594D series”
D1 - 1A, 40V Schottky Rectifier, Surface Mount
L1 - 68 µH, L30, Coilcraft DO3316
CB - 0.01 µF, 50V, Ceramic
R1 - 1k, 1%
R2 - Use formula in Design Procedure

FIGURE 18. PC Board Layout

Layout is very important in switching regulator designs. Rap- If open core inductors are used, special care must be
idly switching currents associated with wiring inductance can taken as to the location and positioning of this type of induc-
generate voltage transients which can cause problems. For tor. Allowing the inductor flux to intersect sensitive feedback,
minimal inductance and ground loops, the wires indicated by IC ground path, and COUT wiring can cause problems.
heavy lines (in Figure 2 and Figure 3) should be wide When using the adjustable version, special care must be
printed circuit traces and should be kept as short as taken as to the location of the feedback resistors and the
possible. For best results, external components should be associated wiring. Physically locate both resistors near the
located as close to the switcher IC as possible using ground IC, and route the wiring away from the inductor, especially an
plane construction or single point grounding. open core type of inductor.

21 www.national.com
LM2672
Application Information (Continued) well as mounting and soldering specifications, refer to Appli-
cation Note AN-1187.
LLP Package Devices
The LM2672 is offered in the 16 lead LLP surface mount
package to allow for increased power dissipation compared
to the SO-8 and DIP. For details on thermal performance as

www.national.com 22
 LM2672
Physical Dimensions inches (millimeters)
unless otherwise noted

8-Lead (0.150" Wide) Molded Small Outline Package, JEDEC

Order Number LM2672M-3.3, LM2672M-5.0,
LM2672M-12 or LM2672M-ADJ
NS Package Number M08A

23 www.national.com
LM2672
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

8-Lead (0.300" Wide) Molded Dual-In-Line Package

Order Number LM2672N-3.3, LM2672N-5.0,
LM2672N-12 or LM2672N-ADJ
NS Package Number N08E

www.national.com 24
 with Features
LM2672 SIMPLE SWITCHER Power Converter High Efficiency 1A Step-Down Voltage Regulator
Physical Dimensions inches (millimeters) unless otherwise noted (Continued)

16-Lead LLP Surface Mount Package

NS Package Number LDA16A

LIFE SUPPORT POLICY

NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or 2. A critical component is any component of a life
systems which, (a) are intended for surgical implant support device or system whose failure to perform
into the body, or (b) support or sustain life, and can be reasonably expected to cause the failure of
whose failure to perform when properly used in the life support device or system, or to affect its
accordance with instructions for use provided in the safety or effectiveness.
labeling, can be reasonably expected to result in a
significant injury to the user.
National Semiconductor National Semiconductor National Semiconductor National Semiconductor
Corporation Europe Asia Pacific Customer Japan Ltd.
Americas Fax: +49 (0) 180-530 85 86 Response Group Tel: 81-3-5639-7560
Tel: 1-800-272-9959 Email: europe.support@nsc.com Tel: 65-2544466 Fax: 81-3-5639-7507
Fax: 1-800-737-7018 Deutsch Tel: +49 (0) 69 9508 6208 Fax: 65-2504466
Email: support@nsc.com English Tel: +44 (0) 870 24 0 2171 Email: ap.support@nsc.com
www.national.com Français Tel: +33 (0) 1 41 91 8790

National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.