Size and Weight: 5.500'' 24.70 ppf 0.

415'' wall IEU

Grade: HS3-125
Drill Pipe Performance Sheet Range: 2
Asset Number: WS41-36 Tool Joint: 6.625'' x 4.000'' XT54

Pipe Body: Tubular Assembly:

Nominal Ultra Class Premium
100% RBW 95% RBW 90% RBW 80% RBW Adjusted Weight (lbs/ft): 28.50 Fluid Displacement (gal/ft): 0.43
Approximate Length (ft): 31.5 Fluid Displacement (bbls/ft): 0.0104
OD (in): 5.500 5.459 5.417 5.334
Wall Thickness (in): 0.415 0.394 0.374 0.332 Box TJ Length (in): 18 Fluid Capacity w/IPC (gal/ft): 0.84
Nominal ID (in): 4.670 4.670 4.670 4.670 Pin TJ Length (in): 12 Fluid Capacity w/IPC (bbls/ft): 0.0201

Tensile Strength (lbs): 828,702 784,055 739,745 652,141 Upset Type: IEU Fluid Capacity w/o IPC (gal/ft): Not Reported
Torsional Strength (ft-lbs): 94,290 89,103 83,971 73,867 Max Upset OD (in): 5.688 Fluid Capacity w/o IPC (bbls/ft): Not Reported
Drift Size (in): 3.875
Burst Capacity (psi): 16,506 17,920 16,977 15,091
Collapse Capacity (psi): 16,060 14,753 13,426 10,711

Note: These are OEM values that may vary with actual values due to mill tolerances, IPC tolerances, OEM rounding, and other
Notes: Body properties are calculated based on uniform OD and wall thickness. factors. Pipe is purchased at a guaranteed 95% RBW. IPC is applied to a nominal thickness of 0.009''. Pipe will have an ID of 4.61'',
Burst capacity for Nominal (100% RBW) based on 87.5% RBW per API. which is smaller than pipe purchased at 87.5%.

Connection: XT54 1.0 FF 1.1 FF 1.15 FF Elevator Shoulder:

TJ OD (in): 6.625
TJ ID (in):4.000 18
MYS (ksi): 120 Maximum MUT (ft-lbs): 49,900 54,890 57,385 Smooth Edge Height (in): 3/32
Maximum MUT is recommended
based on thread compound Tension at Shoulder Separation @ Max MUT (lbs): Tensile Limited Tensile Limited Tensile Limited Smooth Edge OD (in): 6.813
friction factor (unless stated). Tension at Connection Yield @ Max MUT (lbs): 953,400 953,400 953,400 SE Elevator Shoulder Capacity (lbs): 1,091,200
Lower than maximum MUT
should only be used when MUT
is limited by rig equipment or Minimum MUT (ft-lbs): 41,600 45,760 47,840 Nominal TJ OD (in): 6.625
connection tensile. Lower than Tension at Shoulder Separation @ Min MUT (lbs): 1,123,300 1,123,300 1,123,300 Nominal TJ OD Elevator Shoulder Capacity (lbs): 873,300
minimum MUT should never be
used. Tension at Connection Yield @ Min MUT (lbs): 1,147,200 1,147,200 1,147,200 Assumed Elevator Bore (in): 5.813

N/A Tool Joint Torsional Strength (ft-lbs): 83,200 91,520 95,680

N/A Tool Joint Tensile Strength (lbs): 1,147,200 1,147,200 1,147,200
XT54 is a trademark of NOV Grant Prideco. Note: Elevator capacity based on assumed elevator bore, no wear factor, and contact
Note: There is no published pressure rating for this connection. stress of 110, 100 psi. An increased elevator shoulder OD increases elevator
capacity without affecting make-up torque.
*ADJUST makeup torque according to thread compound friction factor (FF) greater than 1.0 up to 1.15 FF. Not to exceed 1.15 regardless of dope FF.* Reference Page 3

The technical information contained herein, including the product performance sheet and other attached documents, has been extracted from information available from the manufacturer and is for reference only and not a recommendation. The user is fully responsible for the accuracy and suitability of use of the technical
information. Workstrings International cannot assume responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated based on uniform OD and wall thickness. No safety factor is applied. The information provided for various
inspection classes and for various wear conditions (remaining body wall) is for information only and does not represent or imply acceptable operation limits. It is the responsibility of the customer and the end user to determine the appropriate performance ratings, acceptable use of the product, maintain safe operational practices,
and to apply a prudent safety factor suitable for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the IADC drilling manual, it is recommended that drilling torque should not exceed 80% of MUT.

www.workstringsinternational.com 24-Jun-20
Download the Workstrings International Pipe Specification App on the App Store℠ or Google Play™
Drill Pipe Performance Sheet

Combined Loading for Drill Pipe Connection Wear Table

Connection: XT™54 6.625" x 4.0" (120-130CY KSI SMYS) Connection: XT™54 6.625" x 4.0" (120-130CY KSI SMYS)
Pipe: 5.5" OD 0.415 " Wall Thickness HS³-125™ 80% Inspection Class Tool Joint OD (in) Max MUT(ft-lbs) Min MUT(ft-lbs)
At Max MUT (49900 ft-lbs ) At Min MUT (41600 ft-lbs ) 6.625 49900 41600
Operational Assembly Max Operational Assembly Max 6.597 48900 40800
Torque(ft-lbs) Tension(lbs) Torque(ft-lbs) Tension(lbs) 6.568 47900 40000
0 652100 0 652100 6.54 47000 39200
2300 651800 1800 651900 6.512 46000 38400
4500 650900 3600 651400 6.483 45100 37500
6800 649400 5400 650400 6.455 44100 36800
9100 647200 7200 649000 6.426 43100 36000
11400 644300 9000 647300 6.398 42200 35200
13600 641000 10800 645100 6.37 41300 34400
15900 636900 12600 642600 6.341 40400 33600
18200 632000 14400 639600 6.313 39400 32900
20500 626500 16200 636300
22700 620600 18100 632300 Elevator Capacity
25000 613700 19900 628000 Bore Diameter: 5.813 Elevator SMYS: 110,100 psi 5.5in. 0.415 in. wall IEU
27300 606000 21700 623400 HS³-125™ XT™54
29600 597500 23500 618300 Tool Joint OD (in) Elevator Hoist Elevator Hoist
31800 588600 25300 612700 Capacity(lbs) No Wear Capacity(lbs) 1/32 In.
34100 578500 27100 606700 Wear Factor
36400 567500 28900 600200 6.313 524300 511700
38700 555500 30700 593200 6.358 573600 561000
40900 543000 32500 585600 6.404 624400 611800
43200 529000 34300 577600 6.449 674400 661800
6.495 725900 713300
6.54 776600 764000
The Technical information contained herein, including the product performance sheet and other attached documents, is for reference only and should not be
6.585 827600 815100
consider as a recommendation. The user is fully responsible for the accuracy and suitability of use of the technical information. NOV Grant Prideco cannot assume

responsibility for the results obtained through the use of this material. No expressed or implied warranty is intended. Drill pipe assembly properties are calculated 6.631 880200 867600
based on uniform OD and wall thickness. No safety factor is applied. The information provided for various inspection classes and for various wear conditions 6.676 932000 919400
(remaining body wall) is for information only and does not represent or imply acceptable operating limits. It is the responsibility of the customer and the end user
6.722 985300 972700
to determine the appropriate performance ratings, acceptable use of the product, maintain safe operating practices, and to apply a prudent safety factor suitable

for the application. For API connections that have different pin and box IDs, tool joint ID refers to the pin ID. Per Chapter B, Section 4 VII of the drilling manual, it is
6.767 1037800 1025200
recommended that drilling torque should not exceed 80% of MUT. 6.8125 1091200 1078600

NOV Grant Prideco L.P. | 400 North Sam Houston Parkway E, Suite 900 | Houston, TX 77060 Grant Prideco™ 2015-10-08 2
www.nov.com/grantprideco
 Makeup Torque Guidelines
- Good COPPER-BASED thread compound is recommended for rotary-shouldered drill pipe connections by the OEM.
- Be LIBERAL with the thread compound in the box, the base of the box, and on the pin using a copper-based or a
compatible thread compound.
- Ensure 360 DEGREES of coverage of the threads and torque shoulders.
- Ensure 360 DEGREES of coverage on the seal surfaces on completion pipe.
- Always ENSURE proper pipe alignment.
- ADJUST makeup torque according to thread compound Friction Factor (FF) greater than 1.0 FF up to 1.15 FF.
Workstrings Engineering is available for more information.
- MINIMIZE clamp pressure with the tongs or iron roughneck.
- MAXIMIZE the distance between the box shoulder and lower jaw die per OEM guidelines (1”-2” minimum for most
tool joints).
- Use a SLOW rotation speed during spin-up and break-out of the first 5-6 threads - especially critical for premium
and completion connections.

NOTE: More detailed running procedures for proprietary rotary-shouldered connections are available from the OEM’s website

PIPE SPECIFICATION MOBILE APP

Download the Workstrings International Pipe Specification App on the App StoreSM or
Google PlayTM
The App allows users to access specifications for the most commonly used sizes and
connections of drill pipe, landing string, HWDP, drill collars and tubing providing the
option to view and email specification sheets conveniently using your mobile device.
Apple and the Apple logo are trademarks of Apple Inc., registered in the U.S. and other countries. App Store is a service mark of
Apple Inc. Google Play is a trademark of Google Inc.

Global Headquarters Engineering & Marketing EMEA Corporate

1150 Smede Hwy 11330 Clay Road, Suite 200 Kirkton Avenue, Dyce
Broussard, LA 70518 - USA Houston, TX 77041 - USA Aberdeen, AB21 0BF - UK
Phone: +1 337-989-9675 Phone: +1 281-999-0047 Phone: +44 1224-724900
Email: info@workstrings.com Email: marketing@workstrings.com Email: sales.uk@workstrings.com

www.workstringsinternational.com