DX-2300-2690-90-16i-M-R

Model: ATD4516R5

Antenna Specifications
General Electrical Properties
Frequency range (MHz) 2300 - 2400 2496 - 2690
Polarization +45° , -45°
General
Electrical downtilt (°) 2 - 12 , continuously adjustable
parameters
Electrical downtilt tolerance (°) ±1
Grounding DC Ground
Coupling factor between calibration port and each
-26 ±2
antenna port (dB)
Max. amplitude tolerance from calibration port to input
0.7
ports (dB)
Calibration Max. phase tolerance from calibration port to input ports
and 5
(°)
electrical
parameters Ports VSWR 1.5
≥ 20 @ 2°Electrical downtilt ; ≥ 25 @ 3°- 6°Electrical downtilt;
Co-polarization isolation between ports (dB)
≥ 28 @ 7°- 12°Electrical downtilt
≥ 25 @ 2°Electrical downtilt; ≥ 28 @ 3°- 6°Electrical downtilt;
Cross-polarization isolation between ports (dB)
≥ 30 @ 7°- 12°Electrical downtilt

Beamforming Electrical Properties

Frequency range (MHz) 2300 - 2400 2496 - 2690
Horizontal 3dB beam width (°) 90 75
Gain (dBi) 16 17
Single column Cross polar ratio (0°) (dB) 20 20
beam
Side lobe suppression for first side
≥ 18 ≥ 18
lobe above main beam (dB)
Front to back ratio (dB) ≥ 28 ≥ 27
Horizontal 3dB beam width (°) 65 65
Gain (dBi) 17.5 18
Gain roll-off at sector edge (dB) 12 12
65° Broadcast Vertical 3dB beam width (°) 6.5 5.7
beam
Radiation Cross polar ratio (0°) (dB) 22 22
parameters
Front to back ratio (dB) ≥ 30 ≥ 30
Side lobe suppression for first side
≤ -18 ≤ -18
lobe above main beam (dB)
0° direct beam gain (dBi) 21 22
0° direction beam horizontal 3dB
25.5 23
beam width (°)
0° direction beam horizontal side
-12 -12
lobe suppression (dB)
Service beam
±30° direction beam gain (dBi) 20.5 21
0° direction beam cross polar ratio
22 22
(0°) (dB)
0° direction beam front to back ratio
30 30
(dB)

1
 DX-2300-2690-90-16i-M-R
Model: ATD4516R5

Soft Split Electrical Properties

Frequency range (MHz) 2300 - 2400 2496 - 2690
Horizontal 3dB beam width (°) 30 27
Gain (dBi) 20.5 21.5
Radiation
parameters Vertical 3dB beam width (°) 6.5 5.7
Multi-beam
Front to back ratio (dB) ≥ 30 ≥ 30
Side lobe suppression for first side
≥ 18 ≥ 18
lobe above main beam (dB)

Notes：
65° broadcast beams and multi-beams are applicable in different scenarios. Select one of them for network coverage based on
site requirements and auxiliary equipment conditions.

106
Mechanical Properties

(58)
Distance between columns (mm) 62
Antenna dimensions (H x W x D) (mm) 1445 x 299 x 109
Packing dimensions (H x W x D) (mm) 1770 x 350 x 180
Antenna weight (kg) 16.0
Clamps weight (kg) 2.9 (2 units)
Antenna packing weight (kg) 22.8 (Included clamps)
Mast diameter supported (mm) 50 - 115

1445
1331
Radome material Fiberglass
Radome colour Light grey
Operational temperature (℃) -40 .. +65
Frontal: 410 (at 150 km/h)
Wind load (N) Lateral: 140 (at 150 km/h)
Maximum: 470 (at 150 km/h)
Max. operational wind speed (km/h) 200
Survival wind speed (km/h) 250
Connector 9 x N Female
Connector position Bottom 56

Accessories
Item Model Description Weight Units per antenna

Downtilt kit ASMDT0B01 Mechanical downtilt: 0 - 16 ° 1.3 kg 1 (Separate packing)

RET S/N: HWMxxx….y

RAE S/N: HWXxxx…..y

y - Yellow

2
 DX-2300-2690-90-16i-M-R
Model: ATD4516R5

Pattern sample for reference

Single 65°
column Broadcast

Service 0° Service 30°

Azimuth Azimuth
-15° +15°

Multi-Beam Multi-Beam
-30° +30°

3
 DX-2300-2690-90-16i-M-R
Model: ATD4516R5

Antenna Information Management Module (AIMM) Specifications

RET Properties
RET type Integrated RET
RET protocols AISG 2.0 / 3GPP
Input voltage range (V) DC 10 - 30
< 1 (when the motor does not work, 12 V)
Power consumption (W) < 3 (when the motor is working, 12 V)
< 10 (when the motor is starting up or shutting down, 12 V)
Adjustment time (full range) (s) Typ. 30
RET interface 1 (RF feeder) Calibration channel integrate the Bias-T and supporting OOK modulation signal communication
2 x 8 pin connector according to IEC 60130-9
RET interface 2 (485 connector)
Daisy chain in: Male / Daisy chain out: Female
1 2 3 4 5 6 7 8
Pin assignment according AISG
DC n/c RS-485B n/c RS-485A DC DC return n/c
Lightning protection (kA) 10 (8/20 μs)

RAE Properties
RAE type Integrated RAE, manages antenna information
RAE protocols AISG-ES-RAE V2.1.0

EasyBeam Properties
Frequency range (MHz) 2300 - 2400 2496 - 2690
Electrical downtilt (°) 2 - 12
Horizontal 3dB beam width (°) 30 65 90 30 65 90
Broadcast
Electrical azimuth (°) -15..+15 0 -15..+15 0
beam
Electrical azimuth step(°) 1 / 1 /

Standards: EN/IEC 60950-1(Safety), EN/IEC 60950-22(Safety – Equipment installed outdoor),EN 55032 (Emission),
EN/IEC 62368-1(Safety)，ETSI EN 301 489, FCC Part15, ICES-003
Certification: CE, FCC, IC, RCM, RoHS, REACH, WEEE

NOTE
1. Facilities, such as towers and poles, must bear the weight and wind load of antennas.
2. HUAWEI ‘s standard brackets and accessories must be used for any installation.
3. The antenna working environment must meet the requirements specified in the datasheet.
4. Only qualified personnel are allowed to perform installation. Installation tools and procedures must conform to
requirements described in the antenna installation guide.

Huawei Technologies Co., Ltd. Bantian, Longgang District, Shenzhen 518129, P.R.China www.huawei.com/antenna
Any previous datasheet issues become invalid. 4 Issue: 2019-12-31