Optionally with push buttons and deadman trigger Industrial-suited robust design Several output options (analog, CAN J1939, CANopen, USB)
The TRY80 series provides very robust joysticks for usage in
tough environments. With optionally available safety features it is also suited for critical applications. Besides standard analog signal output, bus interfaces like USB and CAN J1939 / CAN- open are available.
Electrical Data Joystick
Sensor Hall Effect Supply Voltage 5 VDC ±0.5 VDC transient free Current Consumption Max 10 mA per axis Reverse Polarity Max -10 VDC Overvoltage Max 16 VDC Output Impedance 6 Ohm Resolution Infinite Return to Center Voltage (no Load) ±200 mV initially Output Voltages 0 - 5 V / 0.5 - 4.5 V / 0.25 - 4.75 V / dual signals available
Mechanical Data Joystick
Expected Life 5 million cycles Mechanical Angle of Movement 38° (±19° from center) Break Out Force 7.7 N Operating force 14.0 N Maximum Applied Force 900 N, 20 cm above panel Environmental Sealing (above panel) Stock Grip: up to IP63 (depending on handle configuration), Ball Tip: up to IP67 Operating Temperature -40 °C to +85 °C Storage Temperature -40 °C to +85 °C EMV Immunity Level /V/M) IEC 61000-4-8:2009 EMC Emissions Level IEC 61000-4-3:2006 ESD IEC 61000-4-2:2008
Note: 1. All values are nominal. 2. Exact specifications may be subject to configuration.
Specifications are subject to change without notice
Data Sheet for Joysticks
Hand Joystick Series TRY80
Technical Data Switches
Electrical Load 5 A resistive, 3 A inductive DWV 1050 Vrms Low Level 10 mA at 30 mV Electrical Life 25000 cycles 5 A @ 28 VDC resistive snap-action Mechanical Life 1 million cycles Sealing up to IP63 Action Momentary, snap-action Operating Force 7.5 N ±2 N Total Travel 2 mm + 0.25 mm Available Button Colors White, grey, black, red, orange, yellow, green, blue, purple
Notes: 1. Maximum possible configuration for the stock grip is up to 2 top buttons and 2 side buttons. A handle with deadman trigger can have 2 top buttons, but no side buttons. 2. Maximum possible configuration for the short stock grip is with 1 top button. It is not available with deadman trigger, index trigger or side buttons. 3. If unspecified, the pushbuttons will have snap action momentary switches („normally open“) and red button caps.
Specifications are subject to change without notice
Data Sheet for Joysticks
Hand Joystick Series TRY80
Please contact us for information regarding stock articles, delivery times and minimum order quantities.
Order Code Description Series TRY80 Axes*: 1 Axis 1 2 Axes 2 Sealing: Rubber Boot 5 Spring return: Spring Return 1 Limiter: Square Q Round R Plus P Single Axis X X Single Axis Y Y Handle / Switches: Stock Grip long, no Pushbuttons 1 Ball Tip (no Pushbuttons, IP67) 2 Stock Grip long, 1 Top Pushbutton 3 Stock Grip long, 2 Top Pushbuttons 4 Stock Grip long, 2 Top Pushbuttons, Deadman 5 Stock Grip long, 1 Top Pushb., 2 Side Pushb. 6 Stock Grip long, Top Rocker Switch 9 Stock Grip short, no Pushbutton 7 Stock Grip short, 1 top Pushbutton 8 Output Options: 0 to 5 V single (inverse dual output) 1 (1X) 0.5 to 4.5 V (inverse dual output) 2 (2X) 0.25 to 4.75 V (inverse dual output) 3 (3X) USB Joystick 5 USB Mouse Emulation 6 CAN J1939 CAN CANopen COP Voltage Regulator Supply 6 to 35 VDC, Output 0 to 5 VDC V1205 Supply 11 to 35 VDC, Output ±10 VDC V1210B Special options max. IP grade (above panel)** IP
*For backward compatibility, the codes 3,4,5, and 6 are still valid for all 2 axes versions **IP protection class depends on the handle configuration
For higher quantities or on-going demand, additional options are available
For example: Stock Grip with further push button configurations Customer-specific wiring Redundant output signal (inverted and parallel), discrete output
Specifications are subject to change without notice
Data Sheet for Joysticks
Hand Joystick Series TRY80
Wiring Color Function Color Function Color Function BLACK Ground WHITE Switch Common PURPLE/WHITE Deadman RED Vcc ORANGE Switch 1 BLUE X Axis PURPLE Switch 2 YELLOW Y Axis GREY Switch 3 GREEN Z Axis Note: 1. Standard cable length ca. 400 mm; wires AWG 22 for Joystick, switches, LEDs, etc. 2. For Joysticks with USB interface or mouse emulation a cable is included (USB male type A connector). 3. Wiring can deviate with special output options (CAN-bus, Center Detect, etc.), detailed information will be provided with your product.
Technical Data CAN J1939
Supply Voltage 6 V to 35 V Current Consumption Typical: 15 mA min, +5 mA per LED, +10 mA per Axis CAN SAE J1939 bus specification Operating / Storage Temperature - 25 °C to +70 °C / -40°C to +70°C
Wiring CAN J1939
Colour Function Colour Function Colour Function Red Supply Power Green CAN High data Blue Identifier Select LSB Black Ground GND White CAN Low data Orange Identifier Select MSB
Please contact us for further details on the CANbus interfaces and project-specific solutions.
