Features

High-performance, Low-power AtmelAVR 8-bit Microcontroller Advanced RISC Architecture

130 Powerful Instructions Most Single-clock Cycle Execution 32 x 8 General Purpose Working Registers Fully Static Operation Up to 16 MIPS Throughput at 16MHz On-chip 2-cycle Multiplier High Endurance Non-volatile Memory segments 8KBytes of In-System Self-programmable Flash program memory 512Bytes EEPROM 1KByte Internal SRAM Write/Erase Cycles: 10,000 Flash/100,000 EEPROM Data retention: 20 years at 85C/100 years at 25C(1) Optional Boot Code Section with Independent Lock Bits In-System Programming by On-chip Boot Program True Read-While-Write Operation Programming Lock for Software Security Peripheral Features Two 8-bit Timer/Counters with Separate Prescaler, one Compare Mode One 16-bit Timer/Counter with Separate Prescaler, Compare Mode, and Capture Mode Real Time Counter with Separate Oscillator Three PWM Channels 8-channel ADC in TQFP and QFN/MLF package Eight Channels 10-bit Accuracy 6-channel ADC in PDIP package Six Channels 10-bit Accuracy Byte-oriented Two-wire Serial Interface Programmable Serial USART Master/Slave SPI Serial Interface Programmable Watchdog Timer with Separate On-chip Oscillator On-chip Analog Comparator Special Microcontroller Features Power-on Reset and Programmable Brown-out Detection Internal Calibrated RC Oscillator External and Internal Interrupt Sources Five Sleep Modes: Idle, ADC Noise Reduction, Power-save, Power-down, and Standby I/O and Packages 23 Programmable I/O Lines 28-lead PDIP, 32-lead TQFP, and 32-pad QFN/MLF Operating Voltages 2.7 - 5.5V Speed Grades 0 - 16MHz Power Consumption at 4Mhz, 3V, 25C Active: 3.6mA Idle Mode: 1.0mA Power-down Mode: 0.5A

8-bit with 8KBytes In-System Programmable Flash ATmega8A

Summary

8159DSAVR02/11

ATmega8A
1. Pin Configurations
Figure 1-1. Pinout ATmega8A
PDIP
(RESET) PC6 (RXD) PD0 (TXD) PD1 (INT0) PD2 (INT1) PD3 (XCK/T0) PD4 VCC GND (XTAL1/TOSC1) PB6 (XTAL2/TOSC2) PB7 (T1) PD5 (AIN0) PD6 (AIN1) PD7 (ICP1) PB0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 28 27 26 25 24 23 22 21 20 19 18 17 16 15 PC5 (ADC5/SCL) PC4 (ADC4/SDA) PC3 (ADC3) PC2 (ADC2) PC1 (ADC1) PC0 (ADC0) GND AREF AVCC PB5 (SCK) PB4 (MISO) PB3 (MOSI/OC2) PB2 (SS/OC1B) PB1 (OC1A)

TQFP Top View

PD2 (INT0) PD1 (TXD) PD0 (RXD) PC6 (RESET) PC5 (ADC5/SCL) PC4 (ADC4/SDA) PC3 (ADC3) PC2 (ADC2) 32 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 9 10 11 12 13 14 15 16

(INT1) PD3 (XCK/T0) PD4 GND VCC GND VCC (XTAL1/TOSC1) PB6 (XTAL2/TOSC2) PB7

1 2 3 4 5 6 7 8

PC1 (ADC1) PC0 (ADC0) ADC7 GND AREF ADC6 AVCC PB5 (SCK)

32 31 30 29 28 27 26 25

PD2 (INT0) PD1 (TXD) PD0 (RXD) PC6 (RESET) PC5 (ADC5/SCL) PC4 (ADC4/SDA) PC3 (ADC3) PC2 (ADC2)

(T1) PD5 (AIN0) PD6 (AIN1) PD7 (ICP1) PB0 (OC1A) PB1 (SS/OC1B) PB2 (MOSI/OC2) PB3 (MISO) PB4

MLF Top View

(INT1) PD3 (XCK/T0) PD4 GND VCC GND VCC (XTAL1/TOSC1) PB6 (XTAL2/TOSC2) PB7

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

24 23 22 21 20 19 18 17

PC1 (ADC1) PC0 (ADC0) ADC7 GND AREF ADC6 AVCC PB5 (SCK)

(T1) PD5 (AIN0) PD6 (AIN1) PD7 (ICP1) PB0 (OC1A) PB1 (SS/OC1B) PB2 (MOSI/OC2) PB3 (MISO) PB4

NOTE: The large center pad underneath the MLF packages is made of metal and internally connected to GND. It should be soldered or glued to the PCB to ensure good mechanical stability. If the center pad is left unconneted, the package might loosen from the PCB.

2
8159DSAVR02/11

ATmega8A
2. Overview
The AtmelAVR ATmega8A is a low-power CMOS 8-bit microcontroller based on the AVR RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega8A achieves throughputs approaching 1 MIPS per MHz, allowing the system designer to optimize power consumption versus processing speed.

2.1

Block Diagram
Figure 2-1.
RESET PC0 - PC6 VCC XTAL2 PB0 - PB7

Block Diagram
XTAL1

PORTC DRIVERS/BUFFERS

PORTB DRIVERS/BUFFERS

GND

PORTC DIGITAL INTERFACE

PORTB DIGITAL INTERFACE

MUX & ADC AGND AREF PROGRAM COUNTER

ADC INTERFACE

TWI

STACK POINTER

TIMERS/ COUNTERS

OSCILLATOR

PROGRAM FLASH

SRAM

INTERNAL OSCILLATOR

INSTRUCTION REGISTER

GENERAL PURPOSE REGISTERS X

WATCHDOG TIMER

OSCILLATOR

INSTRUCTION DECODER

Y Z

MCU CTRL. & TIMING

CONTROL LINES

ALU

INTERRUPT UNIT

AVR CPU

STATUS REGISTER

EEPROM

PROGRAMMING LOGIC

SPI

USART

+ -

COMP. INTERFACE

PORTD DIGITAL INTERFACE

PORTD DRIVERS/BUFFERS

PD0 - PD7

3
8159DSAVR02/11

ATmega8A
The AtmelAVR core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. The ATmega8A provides the following features: 8K bytes of In-System Programmable Flash with Read-While-Write capabilities, 512 bytes of EEPROM, 1K byte of SRAM, 23 general purpose I/O lines, 32 general purpose working registers, three flexible Timer/Counters with compare modes, internal and external interrupts, a serial programmable USART, a byte oriented Two-wire Serial Interface, a 6-channel ADC (eight channels in TQFP and QFN/MLF packages) with 10-bit accuracy, a programmable Watchdog Timer with Internal Oscillator, an SPI serial port, and five software selectable power saving modes. The Idle mode stops the CPU while allowing the SRAM, Timer/Counters, SPI port, and interrupt system to continue functioning. The Power-down mode saves the register contents but freezes the Oscillator, disabling all other chip functions until the next Interrupt or Hardware Reset. In Power-save mode, the asynchronous timer continues to run, allowing the user to maintain a timer base while the rest of the device is sleeping. The ADC Noise Reduction mode stops the CPU and all I/O modules except asynchronous timer and ADC, to minimize switching noise during ADC conversions. In Standby mode, the crystal/resonator Oscillator is running while the rest of the device is sleeping. This allows very fast start-up combined with low-power consumption. The device is manufactured using Atmels high density non-volatile memory technology. The Flash Program memory can be reprogrammed In-System through an SPI serial interface, by a conventional non-volatile memory programmer, or by an On-chip boot program running on the AVR core. The boot program can use any interface to download the application program in the Application Flash memory. Software in the Boot Flash Section will continue to run while the Application Flash Section is updated, providing true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic chip, the Atmel ATmega8A is a powerful microcontroller that provides a highly-flexible and cost-effective solution to many embedded control applications. The Atmel AVR ATmega8A is supported with a full suite of program and system development tools, including C compilers, macro assemblers, program debugger/simulators, In-Circuit Emulators, and evaluation kits.

2.2
2.2.1

Pin Descriptions
VCC Digital supply voltage.

2.2.2

GND Ground.

2.2.3

Port B (PB7:PB0) XTAL1/XTAL2/TOSC1/TOSC2 Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset condition becomes active, even if the clock is not running.

4
8159DSAVR02/11

ATmega8A
Depending on the clock selection fuse settings, PB6 can be used as input to the inverting Oscillator amplifier and input to the internal clock operating circuit. Depending on the clock selection fuse settings, PB7 can be used as output from the inverting Oscillator amplifier. If the Internal Calibrated RC Oscillator is used as chip clock source, PB7:6 is used as TOSC2:1 input for the Asynchronous Timer/Counter2 if the AS2 bit in ASSR is set. The various special features of Port B are elaborated in Alternate Functions of Port B on page 58 and System Clock and Clock Options on page 24. 2.2.4 Port C (PC5:PC0) Port C is an 7-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port C output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up resistors are activated. The Port C pins are tri-stated when a reset condition becomes active, even if the clock is not running. PC6/RESET If the RSTDISBL Fuse is programmed, PC6 is used as an I/O pin. Note that the electrical characteristics of PC6 differ from those of the other pins of Port C. If the RSTDISBL Fuse is unprogrammed, PC6 is used as a Reset input. A low level on this pin for longer than the minimum pulse length will generate a Reset, even if the clock is not running. The minimum pulse length is given in Table 25-3 on page 247. Shorter pulses are not guaranteed to generate a Reset. The various special features of Port C are elaborated on page 61. 2.2.6 Port D (PD7:PD0) Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port D output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port D also serves the functions of various special features of the ATmega8A as listed on page 63. 2.2.7 RESET Reset input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the clock is not running. The minimum pulse length is given in Table 25-3 on page 247. Shorter pulses are not guaranteed to generate a reset. 2.2.8 AVCC AVCC is the supply voltage pin for the A/D Converter, Port C (3:0), and ADC (7:6). It should be externally connected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low-pass filter. Note that Port C (5:4) use digital supply voltage, VCC. 2.2.9 AREF AREF is the analog reference pin for the A/D Converter.

2.2.5

5
8159DSAVR02/11

ATmega8A
2.2.10 ADC7:6 (TQFP and QFN/MLF Package Only) In the TQFP and QFN/MLF package, ADC7:6 serve as analog inputs to the A/D converter. These pins are powered from the analog supply and serve as 10-bit ADC channels.

3. Resources
A comprehensive set of development tools, application notes and datasheets are available for download on http://www.atmel.com/avr.
Note: 1.

4. Data Retention
Reliability Qualification results show that the projected data retention failure rate is much less than 1PPM over 20 years at 85C or 100 years at 25C.

6
8159DSAVR02/11

ATmega8A
5. Register Summary
Address
0x3F (0x5F) 0x3E (0x5E) 0x3D (0x5D) 0x3C (0x5C) 0x3B (0x5B) 0x3A (0x5A) 0x39 (0x59) 0x38 (0x58) 0x37 (0x57) 0x36 (0x56) 0x35 (0x55) 0x34 (0x54) 0x33 (0x53) 0x32 (0x52) 0x31 (0x51) 0x30 (0x50) 0x2F (0x4F) 0x2E (0x4E) 0x2D (0x4D) 0x2C (0x4C) 0x2B (0x4B) 0x2A (0x4A) 0x29 (0x49) 0x28 (0x48) 0x27 (0x47) 0x26 (0x46) 0x25 (0x45) 0x24 (0x44) 0x23 (0x43) 0x22 (0x42) 0x21 (0x41) 0x20(1) (0x40)(1) 0x1F (0x3F) 0x1E (0x3E) 0x1D (0x3D) 0x1C (0x3C) 0x1B (0x3B) 0x1A (0x3A) 0x19 (0x39) 0x18 (0x38) 0x17 (0x37) 0x16 (0x36) 0x15 (0x35) 0x14 (0x34) 0x13 (0x33) 0x12 (0x32) 0x11 (0x31) 0x10 (0x30) 0x0F (0x2F) 0x0E (0x2E) 0x0D (0x2D) 0x0C (0x2C) 0x0B (0x2B) 0x0A (0x2A) 0x09 (0x29) 0x08 (0x28) 0x07 (0x27) 0x06 (0x26) 0x05 (0x25) 0x04 (0x24) 0x03 (0x23) 0x02 (0x22)

Name
SREG SPH SPL Reserved GICR GIFR TIMSK TIFR SPMCR TWCR MCUCR MCUCSR TCCR0 TCNT0 OSCCAL SFIOR TCCR1A TCCR1B TCNT1H TCNT1L OCR1AH OCR1AL OCR1BH OCR1BL ICR1H ICR1L TCCR2 TCNT2 OCR2 ASSR WDTCR UBRRH UCSRC EEARH EEARL EEDR EECR Reserved Reserved Reserved PORTB DDRB PINB PORTC DDRC PINC PORTD DDRD PIND SPDR SPSR SPCR UDR UCSRA UCSRB UBRRL ACSR ADMUX ADCSRA ADCH ADCL TWDR TWAR

Bit 7
I SP7 INT1 INTF1 OCIE2 OCF2 SPMIE TWINT SE

Bit 6
T SP6 INT0 INTF0 TOIE2 TOV2 RWWSB TWEA SM2

Bit 5
H SP5 TICIE1 ICF1 TWSTA SM1

Bit 4
S SP4 OCIE1A OCF1A RWWSRE TWSTO SM0

Bit 3
V SP3 OCIE1B OCF1B BLBSET TWWC ISC11 WDRF

Bit 2
N SP10 SP2 TOIE1 TOV1 PGWRT TWEN ISC10 BORF CS02

Bit 1
Z SP9 SP1 IVSEL PGERS ISC01 EXTRF CS01

Bit 0
C SP8 SP0 IVCE TOIE0 TOV0 SPMEN TWIE ISC00 PORF CS00

Page
8 11 11 48, 68 69 73, 104, 124 74, 104, 104 224 191 36, 67 43 73 73 31

Timer/Counter0 (8 Bits) Oscillator Calibration Register COM1A1 ICNC1 COM1A0 ICES1 COM1B1 COM1B0 WGM13 ACME FOC1A WGM12 PUD FOC1B CS12 PSR2 WGM11 CS11 PSR10 WGM10 CS10

57, 77, 125, 196 99 101 102 102 103 103 103 103 103 103

Timer/Counter1 Counter Register High byte Timer/Counter1 Counter Register Low byte Timer/Counter1 Output Compare Register A High byte Timer/Counter1 Output Compare Register A Low byte Timer/Counter1 Output Compare Register B High byte Timer/Counter1 Output Compare Register B Low byte Timer/Counter1 Input Capture Register High byte Timer/Counter1 Input Capture Register Low byte FOC2 WGM20 COM21 COM20 WGM21 CS22 CS21 CS20 Timer/Counter2 (8 Bits) Timer/Counter2 Output Compare Register URSEL URSEL EEAR7 UMSEL EEAR6 UPM1 EEAR5 WDCE UPM0 EEAR4 USBS EEAR3 EERIE EEAR2 EEMWE AS2 WDE TCN2UB WDP2 UCSZ1 OCR2UB WDP1 UBRR[11:8] UCSZ0 EEAR1 EEWE UCPOL EEAR8 EEAR0 EERE TCR2UB WDP0

121 123 123 123 43 160 159 19 19 19 19

EEPROM Data Register

PORTB7 DDB7 PINB7 PORTD7 DDD7 PIND7 SPIF SPIE RXC RXCIE ACD REFS1 ADEN

PORTB6 DDB6 PINB6 PORTC6 DDC6 PINC6 PORTD6 DDD6 PIND6 WCOL SPE TXC TXCIE ACBG REFS0 ADSC

PORTB5 DDB5 PINB5 PORTC5 DDC5 PINC5 PORTD5 DDD5 PIND5 DORD UDRE UDRIE ACO ADLAR ADFR

PORTB4 DDB4 PINB4 PORTC4 DDC4 PINC4 PORTD4 DDD4 PIND4 MSTR FE RXEN ACI ADIF

PORTB3 DDB3 PINB3 PORTC3 DDC3 PINC3 PORTD3 DDD3 PIND3 CPOL DOR TXEN ACIE MUX3 ADIE

PORTB2 DDB2 PINB2 PORTC2 DDC2 PINC2 PORTD2 DDD2 PIND2 CPHA PE UCSZ2 ACIC MUX2 ADPS2

PORTB1 DDB1 PINB1 PORTC1 DDC1 PINC1 PORTD1 DDD1 PIND1 SPR1 U2X RXB8 ACIS1 MUX1 ADPS1

PORTB0 DDB0 PINB0 PORTC0 DDC0 PINC0 PORTD0 DDD0 PIND0 SPI2X SPR0 MPCM TXB8 ACIS0 MUX0 ADPS0

65 65 65 65 65 65 65 65 66 135 134 133 156 157 158 160 196 208 209 210 210 193

SPI Data Register

USART I/O Data Register

USART Baud Rate Register Low byte

ADC Data Register High byte ADC Data Register Low byte Two-wire Serial Interface Data Register TWA6 TWA5 TWA4 TWA3 TWA2 TWA1 TWA0 TWGCE

194

7
8159DSAVR02/11

ATmega8A
5. Register Summary (Continued)
Address
0x01 (0x21) 0x00 (0x20)

Name
TWSR TWBR

Bit 7
TWS7

Bit 6
TWS6

Bit 5
TWS5

Bit 4
TWS4

Bit 3
TWS3

Bit 2

Bit 1
TWPS1

Bit 0
TWPS0

Page
193 191

Two-wire Serial Interface Bit Rate Register

Note:

1. Refer to the USART description for details on how to access UBRRH and UCSRC. 2. For compatibility with future devices, reserved bits should be written to zero if accessed. Reserved I/O memory addresses should never be written. 3. Some of the Status Flags are cleared by writing a logical one to them. Note that the CBI and SBI instructions will operate on all bits in the I/O Register, writing a one back into any flag read as set, thus clearing the flag. The CBI and SBI instructions work with registers 0x00 to 0x1F only.

8
8159DSAVR02/11

ATmega8A
6. Instruction Set Summary
Mnemonics
ADD ADC ADIW SUB SUBI SBC SBCI SBIW AND ANDI OR ORI EOR COM NEG SBR CBR INC DEC TST CLR SER MUL MULS MULSU FMUL FMULS FMULSU RJMP IJMP RCALL ICALL RET RETI CPSE CP CPC CPI SBRC SBRS SBIC SBIS BRBS BRBC BREQ BRNE BRCS BRCC BRSH BRLO BRMI BRPL BRGE BRLT BRHS BRHC BRTS BRTC BRVS BRVC Rd,Rr Rd,Rr Rd,Rr Rd,K Rr, b Rr, b P, b P, b s, k s, k k k k k k k k k k k k k k k k k k

Operands
Rd, Rr Rd, Rr Rdl,K Rd, Rr Rd, K Rd, Rr Rd, K Rdl,K Rd, Rr Rd, K Rd, Rr Rd, K Rd, Rr Rd Rd Rd,K Rd,K Rd Rd Rd Rd Rd Rd, Rr Rd, Rr Rd, Rr Rd, Rr Rd, Rr Rd, Rr k Add two Registers

Description
Rd Rd + Rr

Operation

Flags
Z,C,N,V,H Z,C,N,V,H Z,C,N,V,S Z,C,N,V,H Z,C,N,V,H Z,C,N,V,H Z,C,N,V,H Z,C,N,V,S Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V Z,C,N,V Z,C,N,V,H Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V Z,N,V None Z,C Z,C Z,C Z,C Z,C Z,C None None None None None I None Z, N,V,C,H Z, N,V,C,H Z, N,V,C,H None None None None None None None None None None None None None None None None None None None None None None

#Clocks
1 1 2 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 2 2 2 2 2 2 2 3 3 4 4 1/2/3 1 1 1 1/2/3 1/2/3 1/2/3 1/2/3 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2 1/2

ARITHMETIC AND LOGIC INSTRUCTIONS Add with Carry two Registers Add Immediate to Word Subtract two Registers Subtract Constant from Register Subtract with Carry two Registers Subtract with Carry Constant from Reg. Subtract Immediate from Word Logical AND Registers Logical AND Register and Constant Logical OR Registers Logical OR Register and Constant Exclusive OR Registers Ones Complement Twos Complement Set Bit(s) in Register Clear Bit(s) in Register Increment Decrement Test for Zero or Minus Clear Register Set Register Multiply Unsigned Multiply Signed Multiply Signed with Unsigned Fractional Multiply Unsigned Fractional Multiply Signed Fractional Multiply Signed with Unsigned Relative Jump Indirect Jump to (Z) Relative Subroutine Call Indirect Call to (Z) Subroutine Return Interrupt Return Compare, Skip if Equal Compare Compare with Carry Compare Register with Immediate Skip if Bit in Register Cleared Skip if Bit in Register is Set Skip if Bit in I/O Register Cleared Skip if Bit in I/O Register is Set Branch if Status Flag Set Branch if Status Flag Cleared Branch if Equal Branch if Not Equal Branch if Carry Set Branch if Carry Cleared Branch if Same or Higher Branch if Lower Branch if Minus Branch if Plus Branch if Greater or Equal, Signed Branch if Less Than Zero, Signed Branch if Half Carry Flag Set Branch if Half Carry Flag Cleared Branch if T Flag Set Branch if T Flag Cleared Branch if Overflow Flag is Set Branch if Overflow Flag is Cleared Rd Rd + Rr + C Rdh:Rdl Rdh:Rdl + K Rd Rd - Rr Rd Rd - K Rd Rd - Rr - C Rd Rd - K - C Rdh:Rdl Rdh:Rdl - K Rd Rd Rr Rd Rd K Rd Rd v Rr Rd Rd v K Rd Rd Rr Rd 0xFF Rd Rd 0x00 Rd Rd Rd v K Rd Rd (0xFF - K) Rd Rd + 1 Rd Rd 1 Rd Rd Rd Rd Rd Rd Rd 0xFF R1:R0 Rd x Rr R1:R0 Rd x Rr R1:R0 Rd x Rr

1 R1:R0 (Rd x Rr) << 1 R1:R0 (Rd x Rr) << 1

PC PC + k + 1 PC Z PC PC + k + 1 PC Z PC STACK PC STACK if (Rd = Rr) PC PC + 2 or 3 Rd Rr Rd Rr C Rd K if (Rr(b)=0) PC PC + 2 or 3 if (Rr(b)=1) PC PC + 2 or 3 if (P(b)=0) PC PC + 2 or 3 if (P(b)=1) PC PC + 2 or 3 if (SREG(s) = 1) then PCPC+k + 1 if (SREG(s) = 0) then PCPC+k + 1 if (Z = 1) then PC PC + k + 1 if (Z = 0) then PC PC + k + 1 if (C = 1) then PC PC + k + 1 if (C = 0) then PC PC + k + 1 if (C = 0) then PC PC + k + 1 if (C = 1) then PC PC + k + 1 if (N = 1) then PC PC + k + 1 if (N = 0) then PC PC + k + 1 if (N V= 0) then PC PC + k + 1 if (N V= 1) then PC PC + k + 1 if (H = 1) then PC PC + k + 1 if (H = 0) then PC PC + k + 1 if (T = 1) then PC PC + k + 1 if (T = 0) then PC PC + k + 1 if (V = 1) then PC PC + k + 1 if (V = 0) then PC PC + k + 1

R1:R0 (Rd x Rr) <<

BRANCH INSTRUCTIONS

Mnemonics

Operands

Description

Operation

Flags

#Clocks

9
8159DSAVR02/11

ATmega8A
6. Instruction Set Summary (Continued)
BRIE BRID MOV MOVW LDI LD LD LD LD LD LD LDD LD LD LD LDD LDS ST ST ST ST ST ST STD ST ST ST STD STS LPM LPM LPM SPM IN OUT PUSH POP SBI CBI LSL LSR ROL ROR ASR SWAP BSET BCLR BST BLD SEC CLC SEN CLN SEZ CLZ SEI CLI SES CLS SEV CLV SET Rd, P P, Rr Rr Rd P,b P,b Rd Rd Rd Rd Rd Rd s s Rr, b Rd, b Rd, Z Rd, Z+ k k Rd, Rr Rd, Rr Rd, K Rd, X Rd, X+ Rd, - X Rd, Y Rd, Y+ Rd, - Y Rd,Y+q Rd, Z Rd, Z+ Rd, -Z Rd, Z+q Rd, k X, Rr X+, Rr - X, Rr Y, Rr Y+, Rr - Y, Rr Y+q,Rr Z, Rr Z+, Rr -Z, Rr Z+q,Rr k, Rr Branch if Interrupt Enabled Branch if Interrupt Disabled Move Between Registers Copy Register Word Load Immediate Load Indirect Load Indirect and Post-Inc. Load Indirect and Pre-Dec. Load Indirect Load Indirect and Post-Inc. Load Indirect and Pre-Dec. Load Indirect with Displacement Load Indirect Load Indirect and Post-Inc. Load Indirect and Pre-Dec. Load Indirect with Displacement Load Direct from SRAM Store Indirect Store Indirect and Post-Inc. Store Indirect and Pre-Dec. Store Indirect Store Indirect and Post-Inc. Store Indirect and Pre-Dec. Store Indirect with Displacement Store Indirect Store Indirect and Post-Inc. Store Indirect and Pre-Dec. Store Indirect with Displacement Store Direct to SRAM Load Program Memory Load Program Memory Load Program Memory and Post-Inc Store Program Memory In Port Out Port Push Register on Stack Pop Register from Stack Set Bit in I/O Register Clear Bit in I/O Register Logical Shift Left Logical Shift Right Rotate Left Through Carry Rotate Right Through Carry Arithmetic Shift Right Swap Nibbles Flag Set Flag Clear Bit Store from Register to T Bit load from T to Register Set Carry Clear Carry Set Negative Flag Clear Negative Flag Set Zero Flag Clear Zero Flag Global Interrupt Enable Global Interrupt Disable Set Signed Test Flag Clear Signed Test Flag Set Twos Complement Overflow. Clear Twos Complement Overflow Set T in SREG if ( I = 1) then PC PC + k + 1 if ( I = 0) then PC PC + k + 1 Rd Rr Rd+1:Rd Rr+1:Rr Rd K Rd (X) Rd (X), X X + 1 X X - 1, Rd (X) Rd (Y) Rd (Y), Y Y + 1 Y Y - 1, Rd (Y) Rd (Y + q) Rd (Z) Rd (Z), Z Z+1 Z Z - 1, Rd (Z) Rd (Z + q) Rd (k) (X) Rr (X) Rr, X X + 1 X X - 1, (X) Rr (Y) Rr (Y) Rr, Y Y + 1 Y Y - 1, (Y) Rr (Y + q) Rr (Z) Rr (Z) Rr, Z Z + 1 Z Z - 1, (Z) Rr (Z + q) Rr (k) Rr R0 (Z) Rd (Z) Rd (Z), Z Z+1 (Z) R1:R0 Rd P P Rr STACK Rr Rd STACK I/O(P,b) 1 I/O(P,b) 0 Rd(n+1) Rd(n), Rd(0) 0 Rd(n) Rd(n+1), Rd(7) 0 Rd(0)C,Rd(n+1) Rd(n),CRd(7) Rd(7)C,Rd(n) Rd(n+1),CRd(0) Rd(n) Rd(n+1), n=0:6 Rd(3:0)Rd(7:4),Rd(7:4)Rd(3:0) SREG(s) 1 SREG(s) 0 T Rr(b) Rd(b) T C1 C0 N1 N0 Z1 Z0 I1 I0 S1 S0 V1 V0 T1 None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None None Z,C,N,V Z,C,N,V Z,C,N,V Z,C,N,V Z,C,N,V None SREG(s) SREG(s) T None C C N N Z Z I I S S V V T 1/2 1/2 1 1 1 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 3 3 3 1 1 2 2 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 DATA TRANSFER INSTRUCTIONS

BIT AND BIT-TEST INSTRUCTIONS

Mnemonics

Operands

Description

Operation

Flags

#Clocks

10
8159DSAVR02/11

ATmega8A
6. Instruction Set Summary (Continued)
CLT SEH CLH Clear T in SREG Set Half Carry Flag in SREG Clear Half Carry Flag in SREG T0 H1 H0 T H H 1 1 1

MCU CONTROL INSTRUCTIONS NOP SLEEP WDR

No Operation Sleep Watchdog Reset

(see specific descr. for Sleep function) (see specific descr. for WDR/timer)

None None None

1 1 1

11
8159DSAVR02/11

ATmega8A

7. Ordering Information
Speed (MHz) Power Supply (V) Ordering Code(2) ATmega8A-AU ATmega8A-AUR(3) ATmega8A-PU ATmega8A-MU ATmega8A-MUR(3) Package(1) 32A 32A 28P3 32M1-A 32M1-A Operation Range

16

2.7 - 5.5

Industrial (-40C to 85C)

Notes:

1. This device can also be supplied in wafer form. Please contact your local Atmel sales office for detailed ordering information and minimum quantities. 2. Pb-free packaging alternative, complies to the European Directive for Restriction of Hazardous Substances (RoHS directive). Also Halide free and fully Green. 3. Tape & Reel

Package Type 32A 28P3 32M1-A 32-lead, Thin (1.0 mm) Plastic Quad Flat Package (TQFP) 28-lead, 0.300 Wide, Plastic Dual Inline Package (PDIP) 32-pad, 5 x 5 x 1.0 body, Lead Pitch 0.50 mm Quad Flat No-Lead/Micro Lead Frame Package (QFN/MLF)

12
8159DSAVR02/11

ATmega8A
8. Packaging Information
8.1 32A

PIN 1 IDENTIFIER

PIN 1 e

B E1 E

D1 D

0~7 A1 L
COMMON DIMENSIONS (Unit of Measure = mm) SYMBOL A A1 A2 D D1 E MIN 0.05 0.95 8.75 6.90 8.75 6.90 0.30 0.09 0.45 NOM 1.00 9.00 7.00 9.00 7.00 0.80 TYP MAX 1.20 0.15 1.05 9.25 7.10 9.25 7.10 0.45 0.20 0.75 Note 2 Note 2 NOTE

A2

Notes: 1. This package conforms to JEDEC reference MS-026, Variation ABA. 2. Dimensions D1 and E1 do not include mold protrusion. Allowable protrusion is 0.25 mm per side. Dimensions D1 and E1 are maximum plastic body size dimensions including mold mismatch. 3. Lead coplanarity is 0.10 mm maximum.

E1 B C L e

2010-10-20 2325 Orchard Parkway San Jose, CA 95131 TITLE 32A, 32-lead, 7 x 7 mm Body Size, 1.0 mm Body Thickness, 0.8 mm Lead Pitch, Thin Profile Plastic Quad Flat Package (TQFP) DRAWING NO. 32A REV. C

13
8159DSAVR02/11

ATmega8A
8.2 28P3

PIN 1

E1

SEATING PLANE

L B1 e E B

B2

A1

(4 PLACES)

C eB

0 ~ 15

REF
SYMBOL A A1 D E E1 B

COMMON DIMENSIONS (Unit of Measure = mm) MIN 0.508 34.544 7.620 7.112 0.381 1.143 0.762 3.175 0.203 NOM MAX 4.5724 34.798 8.255 7.493 0.533 1.397 1.143 3.429 0.356 10.160 Note 1 Note 1 NOTE

Note:

1. Dimensions D and E1 do not include mold Flash or Protrusion. Mold Flash or Protrusion shall not exceed 0.25 mm (0.010").

B1 B2 L C eB e

2.540 TYP

09/28/01 2325 Orchard Parkway San Jose, CA 95131 TITLE 28P3, 28-lead (0.300"/7.62 mm Wide) Plastic Dual Inline Package (PDIP) DRAWING NO. 28P3 REV. B

14
8159DSAVR02/11

ATmega8A
32M1-A

D D1

1 2 3

Pin 1 ID E1 E

SIDE VIEW

TOP VIEW
A2

A3 A1

K
P D2

A
0.08 C

COMMON DIMENSIONS (Unit of Measure = mm) MIN 0.80 NOM 0.90 0.02 0.65 0.20 REF 0.18 4.90 4.70 2.95 4.90 4.70 2.95 0.23 5.00 4.75 3.10 5.00 4.75 3.10 0.50 BSC 0.30 0.20 0.40 0.50 0.60 12o 0.30 5.10 4.80 3.25 5.10 4.80 3.25 MAX 1.00 0.05 1.00 NOTE

SYMBOL A

P
Pin #1 Notch (0.20 R)

1 2 3

A1 A2 A3 E2 b

D D1 D2 E

E1 E2 e L P

BOTTOM VIEW

0
Note: JEDEC Standard MO-220, Fig. 2 (Anvil Singulation), VHHD-2. K

5/25/06 2325 Orchard Parkway San Jose, CA 95131 TITLE 32M1-A, 32-pad, 5 x 5 x 1.0 mm Body, Lead Pitch 0.50 mm, 3.10 mm Exposed Pad, Micro Lead Frame Package (MLF) DRAWING NO. 32M1-A REV. E

15
8159DSAVR02/11

ATmega8A
9. Errata
The revision letter in this section refers to the revision of the ATmega8A device.

9.1

ATmega8A, rev. L

First Analog Comparator conversion may be delayed Interrupts may be lost when writing the timer registers in the asynchronous timer Signature may be Erased in Serial Programming Mode CKOPT Does not Enable Internal Capacitors on XTALn/TOSCn Pins when 32 KHz Oscillator is Used to Clock the Asynchronous Timer/Counter2 Reading EEPROM by using ST or STS to set EERE bit triggers unexpected interrupt request

1. First Analog Comparator conversion may be delayed If the device is powered by a slow rising VCC, the first Analog Comparator conversion will take longer than expected on some devices. Problem Fix / Workaround When the device has been powered or reset, disable then enable theAnalog Comparator before the first conversion. 2. Interrupts may be lost when writing the timer registers in the asynchronous timer The interrupt will be lost if a timer register that is synchronous timer clock is written when the asynchronous Timer/Counter register (TCNTx) is 0x00. Problem Fix / Workaround Always check that the asynchronous Timer/Counter register neither have the value 0xFF nor 0x00 before writing to the asynchronous Timer Control Register (TCCRx), asynchronous Timer Counter Register (TCNTx), or asynchronous Output Compare Register (OCRx). 3. Signature may be Erased in Serial Programming Mode If the signature bytes are read before a chiperase command is completed, the signature may be erased causing the device ID and calibration bytes to disappear. This is critical, especially, if the part is running on internal RC oscillator. Problem Fix / Workaround: Ensure that the chiperase command has exceeded before applying the next command. 4. CKOPT Does not Enable Internal Capacitors on XTALn/TOSCn Pins when 32 KHz Oscillator is Used to Clock the Asynchronous Timer/Counter2 When the internal RC Oscillator is used as the main clock source, it is possible to run the Timer/Counter2 asynchronously by connecting a 32 KHz Oscillator between XTAL1/TOSC1 and XTAL2/TOSC2. But when the internal RC Oscillator is selected as the main clock source, the CKOPT Fuse does not control the internal capacitors on XTAL1/TOSC1 and XTAL2/TOSC2. As long as there are no capacitors connected to XTAL1/TOSC1 and XTAL2/TOSC2, safe operation of the Oscillator is not guaranteed. Problem Fix / Workaround Use external capacitors in the range of 20 - 36 pF on XTAL1/TOSC1 and XTAL2/TOSC2. This will be fixed in ATmega8A Rev. G where the CKOPT Fuse will control internal capacitors also when internal RC Oscillator is selected as main clock source. For ATmega8A Rev. G, CKOPT = 0 (programmed) will enable the internal capacitors on XTAL1 and XTAL2. Customers who want compatibility between Rev. G and older revisions, must ensure that CKOPT is unprogrammed (CKOPT = 1).

16
8159DSAVR02/11

ATmega8A
5. Reading EEPROM by using ST or STS to set EERE bit triggers unexpected interrupt request. Reading EEPROM by using the ST or STS command to set the EERE bit in the EECR register triggers an unexpected EEPROM interrupt request. Problem Fix / Workaround Always use OUT or SBI to set EERE in EECR.

17
8159DSAVR02/11

ATmega8A

10. Datasheet Revision History

Please note that the referring page numbers in this section are referred to this document. The referring revision in this section refers to the document revision.

10.1

Rev.8159D 02/11

1. 2. 3.

Updated the datasheet according to the Atmel new Brand Style Guide. Updated Performing Page Erase by SPM on page 218 by adding an extra note. Updated Ordering Information on page 12 to include Tape & Reel.

10.2

Rev.8159C 07/09

1. 2.

Updated Errata on page 298. Updated the last page with Atmels new addresses.

10.3

Rev.8159BS 05/09

1. 2. 3. 4. 5.

Updated System and Reset Characteristics on page 247 with new BODLEVEL values Updated ADC Characteristics on page 251 with new VINT values. Updated Typical Characteristics view. Updated Errata on page 298. ATmega8A, rev L. Created a new Table Of Contents.

18
8159DSAVR02/11

10.4

Rev.8159AS 08/08

1. 2.

Initial revision (Based on the ATmega8/L datasheet 2486T-AVR-05/08) Changes done compared to ATmega8/L datasheet 2486T-AVR-05/08: All Electrical Characteristics are moved to Electrical Characteristics on page 244. Updated DC Characteristics on page 244 with new VOL Max (0.9V and 0.6V) and typical value for ICC. Added Speed Grades on page 246. Added a new sub section System and Reset Characteristics on page 247. Updated System and Reset Characteristics on page 247 with new VBOT BODLEVEL = 0 (3.6V, 4.0V and 4.2V). Register descriptions are moved to sub section at the end of each chapter. New graphics in Typical Characteristics on page 252. New Ordering Information on page 294.

Atmel Corporation 2325 Orchard Parkway San Jose, CA 95131 USA Tel: (+1)(408) 441-0311 Fax: (+1)(408) 487-2600 www.atmel.com

Atmel Asia Limited Unit 1-5 & 16, 19/F BEA Tower, Millennium City 5 418 Kwun Tong Road Kwun Tong, Kowloon HONG KONG Tel: (+852) 2245-6100 Fax: (+852) 2722-1369

Atmel Munich GmbH Business Campus Parkring 4 D-85748 Garching b. Munich GERMANY Tel: (+49) 89-31970-0 Fax: (+49) 89-3194621

Atmel Japan 9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 JAPAN Tel: (+81)(3) 3523-3551 Fax: (+81)(3) 3523-7581

2011 Atmel Corporation. All rights reserved. / Rev. CORP0XXXX Atmel , Atmel logo and combinations thereof, AVR and others are registered trademarks or trademarks of Atmel Corporation or its subsidiaries. Other terms and product names may be trademarks of others.
Disclaimer: The information in this document is provided in connection with Atmel products. No license, express or implied, by estoppel or otherwise, to any intellectual property right is granted by this document or in connection with the sale of Atmel products. EXCEPT AS SET FORTH IN THE ATMEL TERMS AND CONDITIONS OF SALES LOCATED ON THE ATMEL WEBSITE, ATMEL ASSUMES NO LIABILITY WHATSOEVER AND DISCLAIMS ANY EXPRESS, IMPLIED OR STATUTORY WARRANTY RELATING TO ITS PRODUCTS INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT. IN NO EVENT SHALL ATMEL BE LIABLE FOR ANY DIRECT, INDIRECT, CONSEQUENTIAL, PUNITIVE, SPECIAL OR INCIDENTAL DAMAGES (INCLUDING, WITHOUT LIMITATION, DAMAGES FOR LOSS AND PROFITS, BUSINESS INTERRUPTION, OR LOSS OF INFORMATION) ARISING OUT OF THE USE OR INABILITY TO USE THIS DOCUMENT, EVEN IF ATMEL HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Atmel makes no representations or warranties with respect to the accuracy or completeness of the contents of this document and reserves the right to make changes to specifications and product descriptions at any time without notice. Atmel does not make any commitment to update the information contained herein. Unless specifically provided otherwise, Atmel products are not suitable for, and shall not be used in, automotive applications. Atmel products are not intended, authorized, or warranted for use as components in applications intended to support or sustain life.

8159DSAVR02/11