1.

25G SFP Optical module

Features：
■ Up to 1.25Gbps data rate
■ Duplex LC receptacle optical interface compliant
■ Single +3.3V power supply
■ DDM function implemented
■ Hot-pluggable
■ Receiver Loss of Signal Output
■ AC coupling of PECL signals
■ Serial ID module on MOD(0-2)
■ International Class 1 laser safety certified
■ Transmitter disable input
■ Operating temperature range: 0℃~+70℃
■ RoHS Compliant

Applications：
■ Gigabit Ethernet
■ Switch to switch interface
■ Switched backplane applications
Standard:
■ Compliant with SFP MSA (INF-8074i)
■ Compliant with SFF-8472 v9.3
■ Compliant with IEEE802.3z Gigabit Ethernet

Absolute Maximum Ratings

Parameter Symbol Uint. Min Max
Storage Temperature Range Ts °C -40 +85
Relative Humidity RH % 5 95
Power supply Voltage Vcc V -0.5 4
Recommended Operating Conditions
Parameter Symbol Uint Min Typ Max
Case Operating Temperature Tc °C 0 70
Range
Power Supply Voltage Vcc V 3.135 3.3 3.465
Data Rate - Gb/s - 1.25 -
 Specifications (tested under recommended operating conditions, unless otherwise noted)
1.GSFP-SX-D
Parameter Symbol Unit Min Typ Max Notes
Electrical Characteristics
Tx Section
Supply Current Icc mA - - 300 1
Rx Section
Single Ended Data Input Swing - mV - - 1100
Single Ended Data Output Swing - mV 300 - 600
Optical transmitter Characteristics
Launch Optical Power (EOL) Po dBm -9.5 -3
Center Wavelength Range λc nm 770 850 860
Extinction Ratio EX dB 9
Spectral Width (RMS) ∆λ nm 0.85
Eye Diagram Complies with IEEE802.3z eye masks when filtered
Optical Rise/FaII Time Trise/Tfall ps 260 2
Pout of OFF transmitter Poff dBm - - -45
LD turn-on Time Ton ms 1
LD turn-off Time Toff us 10
Optical receiver Characteristics
Center Wavelength Range λc nm 770 860
Receiver Sensitivity S dBm -20 3
Overload Input Optical Power Pin dBm -3 3
Optical De-assert LOSD dBm -26
LOS
Optical Assert LOSA dBm -30
Notes 1: The supply current includes SFP module’s supply current and test board working current.
Notes 2: Optical transition time is the time interval required for the rising or falling edge of an optical pulse to transition
between the 20% and 80% amplitudes relative to the logical 1 and 0 levels
Notes 3: Measured with a PRBS 223-1 test pattern, @1.25Gb/s, EX=10dB, BER<10-12.

2.GSFP-LX-10-D
Parameter Symbol Unit Min Typ Max Notes
Electrical Characteristics
Tx Section
Supply Current Icc mA - - 300 1
Rx Section
Single Ended Data Input Swing - mV - - 1100
Single Ended Data Output Swing - mV 300 - 600
Optical transmitter Characteristics
Launch Optical Power Po dBm -9 -3
Center Wavelength Range λc nm 1260 1310 1360
 Extinction Ratio EX dB 9
Spectral Width (RMS) ∆λ nm 4
Eye Diagram Complies with IEEE802.3z eye masks when filtered
Optical Rise/Fall Time Trise/Tfall ps 260 2
Pout of OFF transmitter Poff dBm - - -45
LD turn-on Time Ton ms 1
LD turn-off Time Toff us 10
Optical receiver Characteristics
Center Wavelength Range λc nm 1260 1360
Receiver Sensitivity S dBm -25 3
Overload Input Optical Power Pin dBm -3 3
Optical De-assert LOSD dBm -26
LOS
Optical Assert LOSA dBm -35
Notes 1: The supply current includes SFP module’s supply current and test board working current.
Notes 2: Optical transition time is the time interval required for the rising or falling edge of an optical pulse to transition
between the 20% and 80% amplitudes relative to the logical 1 and 0 levels
Notes 3: Measured with a PRBS 223-1 test pattern, @1.25Gb/s, EX=10dB, BER<10-12.

3.GSFP-LX-20-D
Parameter Symbol Uint Min Typ Max Notes
Electrical Characteristics
Tx Section
Supply Current Icc mA - - 300 1
Rx Section
Single Ended Data Input Swing - mV - - 1100
Single Ended Data Output Swing - mV 300 - 600
VOH 2.0 Vcc
TX_fault /LOS output (TTL) V
VOL 0 0.8
VOH 2.0 Vcc
TX_disable input (TTL) V
VOL 0 0.8
Optical transmitter Characteristics
Launch Optical Power Po dBm -9 -3
Center Wavelength Range λc nm 1270 1310 1355
Extinction Ratio EX dB 9
Spectral Width (RMS) ∆λ nm 4
Total transmitter Jitter TJ UI 0.284 2
Relative Intensity Noise RIN DB/Hz -120 3
Eye Diagram Complies with IEEE802.3z eye masks when filtered
Trise/Tfa
Optical Rise/Fall Time ps 260 4
l
 Pout of OFF transmitter Poff dBm - - -45
Optical receiver Characteristics
Center Wavelength Range λc nm 1250 1620
Receiver Sensitivity S dBm -25 5
Overload Input Optical Power Pin dBm -3
Optical De-assert -26
LOS dBm
Optical Assert -35
LOS Hysteresis dB 0.5 3 5 6
Notes 1: The supply current includes SFP module’s supply current and test board working current.
Notes 2: TP2 refers to the compliance point specified in IEEE802.3z, section 38.2.1.
Notes 3: RIN is the laser noise, integrated over a specified bandwidth, measured relative to average optical power with
12dB return loss. For multimode application, the RIN is better than -117dB/Hz.
Notes 4: Optical transition time is the time interval required for the rising or falling edge of an optical pulse to transition
between the 20% and 80% amplitudes relative to the logical 1 and 0 levels
Notes 5: Measured with a PRBS 223-1 test pattern, @1.25Gb/s, EX=10dB, BER<10-12.
Notes 6: The LOS Hysteresis to minimize “chatter” on the output line. In principle, Hysteresis alone does not guarantee
chatter-free operation

4.GSFP-LX-40-D
Parameter Symbol Uint Min Typ Max Notes
Electrical Characteristics
Tx Section
Supply Current Icc mA - 3 300 1
Rx Section
Single Ended Data Input Swing - mV 150 - 1100
Single Ended Data Output Swing - mV 300 - 600
VOH 2.0 Vcc
TX_fault /LOS output (TTL) V
VOL 0 0.8
VOH 2.0 Vcc
TX_disable input (TTL) V
VOL 0 0.8
Optical transmitter Characteristics
Launch Optical Power Po dBm -5 0 40km 1310DFB
Center Wavelength Range λc nm 1270 1310 1350 DFB
Extinction Ratio EX dB 9
Spectral Width ∆λ nm 1 DFB
Side Mode Suppression Ratio SMSR dB 30 DFB
Contributed Total Jitter
TJ UI 0.284 2
added at TP2
dB/H
Relative Intensity Noise RIN -120 3
z
 Eye Diagram Complies with IEEE802.3z eye masks when filtered
Dispersion Penalty dB 1
Optical Rise/Fall Time Trise/Tfal ps 260 4
Optical receiver Characteristics
Receiver Sensitivity S dBm -23 1310nm 40km
Overload Input Optical Power Pin dBm -3 40km
Optical Dessert S
LOS dBm
Optical Assert -35 40km PIN
LOS Hysteresis dB 0.5 3 5 6
Note1. The supply current includes SFP module’s supply current and test board working current.
Note2 TP refers to the compliance point specified in IEEE802.3z, section 38.2.1.
Note3 RIN is the laser noise, integrated over a specified bandwidth, measured relative to average optical
power with 12dB return loss. For multimode application, the RIN is better than -117dB/Hz.
Note4 Optical transition time is the time interval required for the rising or falling edge of an optical pulse
to transition between the 20% and 80% amplitudes relative to the logical 1 and 0 levels
Note5 Measured with a PRBS 223-1 test pattern, @1.25Gb/s, EX=10dB, BER<10-12.
Note6 The LOS Hysteresis to minimize “chatter” on the output line. In principle, Hysteresis alone does not
guarantee chatter-free operation

5.GSFP-ZX-80-D
Parameter Symbol Uint Min Typ Max Notes
Electrical Characteristics
Supply Tx Section
Icc mA - 3 300 1
Current Rx Section
Single Ended Data Input
- mV 150 - 1100
Swing
Single Ended Data Output
- mV 300 - 600
Swing
VOH 2.0 Vcc
TX_fault /LOS output (TTL) V
VOL 0 0.8
VOH 2.0 Vcc
TX_disable input (TTL) V
VOL 0 0.8
Optical transmitter Characteristics
Launch Optical Power Po dBm -2 0 +3 80km 1550nm DFB-LD
Center Wavelength Range λc nm 1500 1550 1580 DFB-LD
Extinction Ratio EX dB 9
Spectral Width ∆λ nm 1 DFB-LD
Side Mode Suppression Ratio SMSR dB 30 DFB-LD
Contributed Total Jitter TJ UI 0.284 2
 added at TP2
dB/H
Relative Intensity Noise RIN -120 3
z
Eye Diagram Complies with IEEE802.3z eye masks when filtered
Dispersion Penalty dB 1
Optical Rise/Fall Time Trise/Tfal ps 260 4
Optical receiver Characteristics
Receiver Sensitivity S dBm -25 1550nm 80km
Overload Input Optical Power Pin dBm -3 80km
Optical
S 5
LOS Dessert dBm
Optical Assert -35 80km PIN
LOS Hysteresis dB 0.5 3 5 6
Note1: The supply current includes SFP module’s supply current and test board working current.
Note2: TP refers to the compliance point specified in IEEE802.3z, section 38.2.1.
Note3: RIN is the laser noise, integrated over a specified bandwidth, measured relative to average optical
power with 12dB return loss. For multimode application, the RIN is better than -117dB/Hz.
Note4: Optical transition time is the time interval required for the rising or falling edge of an optical pulse
to transition between the 20% and 80% amplitudes relative to the logical 1 and 0 levels
Note5: Measured with a PRBS 223-1 test pattern, @1.25Gb/s, EX=10dB, BER<10-12.
Note6: The LOS Hysteresis to minimize “chatter” on the output line. In principle, Hysteresis alone does not guarantee
chatter-free operation

6.GSFP-ZX-120-D
Parameter Symbol Uint Min Typ Max Notes
Electrical Characteristics
Tx Section
Supply Current Icc mA - - 300 1
Rx Section
Single Ended Data Input Swing mV 150 1100
Single Ended Data Output Swing mV 300 600
VOH 2.0 Vcc
TX_fault /LOS output (TTL) V
VOL 0 0.8
VOH 2.0 Vcc
TX_disable input (TTL) V
VOL 0 0.8
Optical transmitter Characteristics
Launch Optical Power Po dBm 0 +5 120km

Center Wavelength Range λc nm 1500 1550 1580

Extinction Ratio EX dB 9

Spectral Width (-20dB) ∆λ nm 1

 Total transmitter Jitter TJ UI 0.284 2

Relative Intensity Noise RIN dB/H z -120 3

Eye Diagram Complies with IEEE802.3z eye masks when filtered

Dispersion Penalty dB 2
Optical Rise/Fall Time Trise/Tfall PS 260 4
P out of OFF transmitter Poff dBm - - -45
Optical receiver Characteristics
Center Wavelength Range λc 1250 1620
Receiver Sensitivity S dBm -30 5
Overload Input Optical Power P in dBm -9
Optical Dessert dBm -31
LOS
Optical Assert dBm -45
LOS Hysteresis dB 0.5 3 5 6
Note l. The supply current includes SFP module's supply current and test board working current.
Note2. TP2 refers to the compliance point specified in IEEE802 3z, section 38.2.1 .
Note3. RIN is the laser noise, integrated over a specified bandwidth, measured relative to average optical power with 12dB
return loss. For multimode application, the RIN is better than -1 17dB/Hz.
Note4: Optical transition time is the time interval required for the rising or falling edge of an optical pulse to transition between
the 20% and 80% amplitudes relative to the logical 1 and 0 levels
Note5. Measured with a PRBS 223-1 test pattern, @1 .25Gb/s, EX=10dB, BER<10-12
Note6. The LOS Hysteresis to minimize "chatter" on the output line. In principle, Hysteresis alone does not guarantee
chatter-free operation.

Ordering Information
Model Description
GE SFP, 550m, 1.25Gbps, Tx 850nm, Rx 850nm, SFP form-factor, Duplex
GSFP-SX-D
LC/UPC receptacle connector, 0~70°C Commercial temperature, DDM

GE SFP, 10km, 1.25Gbps, Tx 1310nm, Rx 1310nm, SFP form-factor, Duplex

GSFP-LX-10-D
LC/UPC receptacle connector, 0~70°C Commercial temperature, DDM

GE SFP, 20km, 1.25Gbps, Tx 1310nm, Rx 1310nm, SFP form-factor, Duplex

GSFP-LX-20-D
LC/UPC receptacle connector, 0~70°C Commercial temperature, DDM

GE SFP, 40km, 1.25Gbps, Tx 1310nm, Rx 1310nm, SFP form-factor, Duplex

GSFP-LX-40-D
LC/UPC receptacle connector, 0~70°C Commercial temperature, DDM

GE SFP, 80km, 1.25Gbps, Tx 1550nm, Rx 1550nm, SFP form-factor, Duplex

GSFP-ZX-80-D
LC/UPC receptacle connector, 0~70°C Commercial temperature, DDM

GE SFP, 120km, 1.25Gbps, Tx 1550nm, Rx 1550nm, SFP form-factor, Duplex

GSFP-ZX-120-D
LC/UPC receptacle connector, 0~70°C Commercial temperature, DDM