SAMYANG ELECTRONICS U1A --- U1M

SAM YANG

VOLTAGE RANGE: 50 --- 1000 V

HIGH EFFICIENCY RECTIFIER CURRENT: 1.0 A

FEATURES
PlasticpackagehasUnderwritersLaboratoryFlammability SOD-123FL
Classification94V-0
Glass passived junction
Low forward voltage drop
High current capability, High reliability 0.039(1.00 ) 0.077(1.95 )
0.020(0.50)
Low power loss, high efficiency 0.054(1.38)

High surge current capability

0.114(2.90 )
High speed switching, Low leakage
0.098(2.50)
High temperature soldering guaranteed:260°C/10 seconds at terminals
0.154(3.90)
Component in accordance to RoHS 2011 / /65 EU 0.138(3.50)

MECHANICAL DATA 0.010(0.25)

5°

MAX 0.052(1.33)
Case: SOD-123 FL molded plastic 0.031(0.8)
Terminals: Solder plated, solderable per MIL-STD-750, Method 2026
Polarity: Color band denotes cathode end 0.010(0.25)
MIN
Mounting Position: Any
TYPE CODE : A/F Marking : USL
Dimensions in inches and (millimeters)
G Marking : USM
J/M Marking : USH

MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS

(Rating at 25°C ambient temperature unless otherwise specified. Single phase ,half wave ,60HZ,resistive or inductive
load. For capacitive load, derate current by 20%.)

Symbols U1A U1B U1D U1F U1G U1J U1K U1M Units
Maximum Recurrent Peak Reverse Voltage VRRM 50 100 200 300 400 600 800 1000 Volts
Maximum RMS Voltage VRMS 35 70 140 210 280 420 560 700 Volts
Maximum DC Blocking Voltage VDC 50 100 200 300 400 600 800 1000 Volts
Maximum Average Forward Rectified Current I(AV) 1.0 Amp
Peak Forward Surge Current 8.3ms single half
sine-wave superimposed on rated load IFSM 30.0 Amps
(JEDEC method)
Maximum Instantaneous Forward Voltage
at 1.0 A VF 1.0 1.4 1.7 Volts

TA=25°C 5.0
Maximum DC Reverse Current
at rated DC blocking voltage
IR μA
TA=125 °C 100

Typical Thermal resistance

RθJA 170 °C/W
RθJL 55

Maximum reverse recovery time(Note1) Trr 50 75 ns

Typical junction capacitance(Note2) CJ 15 PF
Operating junction and storage temperature TJ -65 to+150
range °C
TSTG

Note : 1.Test conditions: IF=0.5A,IR=1.0A,IRR=0.25A.

2.Measured at 1MHZ and applied reverse voltage of 4.0 Volts.

www.diode.co.kr

1.
RATINGS AND CHARACTERISTIC CURVES U1A --- U1M

FIG.1-TEST CIRCUIT DIAGRAM AND REVERSE FIG.2-TYPICAL FORWARD CURRENT

RECOVERY TIME CHARACTERISTIC DERATING CURVE

AVERAGE FORWARD CURRENT (A)

1.0
50 10 Trr
NONINDUCTIVE NONINDUCTIVE +0.5A
0.8

0.6
(＋) D.U.T. PULSE 0
50Vdc GENERATOR
(APPROX) (NOTE2) -0.25A 0.4
(－) SINGLE PHASE HALF WAVE 60HZ
1
OSCILLOSCOPE 0.2
NONIN- RESISTIVE OR INDUCTIVE LOAD
(NOTE1)
DUCTIVE
0
NOTES:1.Rise Time=7ns max. input impedance=1 -1.0A 0 25 50 75 100 125 150 175
megohm 22pF 1cm
2.Rise Time=10ns max. source impedance= SET TIME BASE FOR 50/100 ns/cm LEAD TEMPERATURE (°C)
50 ohms

FIG.3-TYPICAL INSTANTANEOU FORWARD

CHARACTERISTICS FIG.4-TYPICAL REVERSE CHARACTERISTICS

10 100
INSTANTANEOU REVERSE CURRENT (μA)
INSTANTANEOU FORWARD CURRENT( AMPERES)

50\100\200\300V
10 TJ=150°C
1
400\500V

TJ=100°C

1.0

0.1

600\800\1000V TJ=25°C

0.1
TJ=25°C
0.01

Pulse Width=300μs
1% Duty Cycle 0.01
0 20 40 60 80 100 120 140
0.001
0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8
PERCENT OF RATED PEAK REVERSE VOLTAGE(%)
INSTANTANEOU FORWARD VOLTAGE (VOLTS)

FIG.5-MAXIMUM NON-REPETITIVE
FORWARD SURGE CURRENT FIG.6-TYPICAL JUNCTION CAPACITANCE

50 200
8.3ms SINGLE HALF SINE-WAVE 100
JUNCTION CAPACITANCE(pF)

40 (JEDEC Method) 60
PEAK FORWARD SURGE
CURRENT(AMPERES)

40
30
20
U1A-U1G
20 10
6

10 4
TJ=25°C U1J-U1M

0 2
1 5 10 50 100 1
NUMBER OF CYCLES AT 60Hz 0.1 0.2 0.4 1 2 4 10 20 40 100

REVERSE VOLTAGE. (V)

www.diode.co.kr

2.