1 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
1. Summary The STK-PL/A series is based on TMR (Tunneling-Magnetoresistance) technology and open-loop design. It is suitable for DC, AC, pulsed and any kind of irregular current measurement under the isolated conditions. The nominal current range of the STK-PL/A current sensor consists of 10 A, 20 A, 32 A, 40 A, 50 A.
General parameter Parameter Symbol Unit Value Working temperature T_A ℃ -40 ~ 105 Storage temperature T_stg ℃ -40 ~ 105 Mass m g 10 Current line impedance Z mΩ 0.2 Current line temperature rise Tr ℃ 110
Absolute maximum rating
Parameter Symbol Unit Value Supply voltage（non-destructive） VC V 6.0 ESD rating（HBM） UESD kV 4 ESD rating（CDM） UCDM kV 1.5 Remark: the unrecoverable damage may occur when the product works on the conditions over the absolute maximum ratings. Long-time working on the absolute maximum ratings may cause the degradation on performance and reliability.
2 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
Ratings Parameter Symbol Unit Value Primary involved potential V AC/DC 600 Ambient operating temperature T_A ℃ 105 According to series primary Primary current I_p A current Secondary supply voltage U_c V DC 5 Output voltage V_out V 0.1 ~ 4.9
Isolation parameter Parameter Symbol Unit Value Comment RMS voltage for AC test 50Hz/1 Ud kV 5 min Impulse withstand voltage Ûw kV 8 1.2/50µs Shortest distance Clearance distance (pri. -sec) dCI mm 8 through air Shortest path along Creepage distance (pri. -sec) dCp mm 8 device body V0 according Case material to UL 94 Reinforced insulation, CAT III, PD 2, non Application example V 600 uniform field according EN 50178, IEC 61010 Basic insulation, CAT III, PD 2, non uniform field Application example V 1000 according EN 50178, IEC 61010 Basic insulation, CAT III, PD 2, according to IEC Application example V 1500 62109-1 Altitude ≤ 3000 m CAT III, PD 2, according Application example V 600 to UL 508
3 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
2. STK-10PL/A Electrical performance
Condition：T_A = 25℃, Vcc = 5 V (Except special instructions) Parameter Symbol Unit Min Typ Max Comment Primary nominal current rms I_pn A 10 Primary current measuring I_pm A -25 25 range Supply voltage Vcc V 4.75 5 5.25 Current consumption Icc mA 5 10 Reference voltage Vref V 2.48 2.5 2.52 Output function Rated output voltage V_FS V 0.8 (Vout - Vref )@ I_pn Internal output resistance R_out Ω 1 Output Internal output resistance R_ref Ω 1 Output Quiescent voltage Voff V 2.48 2.5 2.52 Vout @ 0 A Electrical offset voltage Voe mV -10 10 (Vout – Vref) @ 0 A Temperature drift of Voe Voe_TRange mV -8 8 -40℃ ~ 105℃ Magnetic offset current I_om A -0.25 0.25 @ ±10 x I_pn Theoretical gain G_th mV/A 80 800 mV @ I_pn Trimmed in the Error of gain Err_G %G_th ±0.5 factory @ 25℃ Temperature drift of gain G_TR %G_th -1.0 1.0 -40℃ ~ 105℃ Rated linearity error Non-L_pn %I_pn -0.5 0.5 ±I_pn Linearity error @ I_pm Non-L_pm %I_pm -1 1 ±I_pm Reaction time t_ra µs 0.5 1 @ 10% of I_pn Step response time t_res µs 1.5 2 @ 90% of I_pn Delay time t_delay µs 1 400 kHz sine wave Frequency bandwidth (-3dB) BW kHz 400 No RC circuit Output voltage noise DC ~ 10 kHz Vnoise mVpp 15 DC ~ 100 kHz 25 Accuracy @ 25℃ X % of I_pn -1 1 @ 25℃ Accuracy @ -40℃ ~ 105℃ X_TRange % of I_pn -2 2 -40℃ ~ 105℃
4 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
3. STK-20PL/A Electrical performance
Condition：T_A = 25℃ Vcc = 5 V (Except special instructions) Parameter Symbol Unit Min Typ Max Comment Primary nominal current rms I_pn A 20 Primary current measuring I_pm A -50 50 range Supply voltage Vcc V 4.75 5 5.25 Current consumption Icc mA 5 10 Reference voltage Vref V 2.48 2.5 2.52 Output function Rated output voltage V_FS V 0.8 (Vout - Vref )@ I_pn Internal output resistance R_out Ω 1 Output Internal output resistance R_ref Ω 1 Output Quiescent voltage Voff V 2.48 2.5 2.52 Vout @ 0 A Electrical offset voltage Voe mV -10 10 (Vout – Vref) @ 0 A Temperature drift of Voe Voe_TRange mV -8 8 -40℃ ~ 105℃ Magnetic offset current I_om A -0.25 0.25 @ ±10 x I_pn Theoretical gain G_th mV/A 40 800 mV @ I_pn Trimmed in the Error of gain Err_G %G_th ±0.5 factory @ 25℃ Temperature drift of gain G_TR %G_th -1.0 1.0 -40℃ ~ 105℃ Rated linearity error Non-L_pn %I_pn -0.5 0.5 ±I_pn Linearity error @ I_pm Non-L_pm %I_pm -1 1 ±I_pm Reaction time t_ra µs 0.5 1 @ 10% of I_pn Step response time t_res µs 1.5 2 @ 90% of I_pn Delay time t_delay µs 1 400 kHz sine wave Frequency bandwidth (-3dB) BW kHz 400 No RC circuit Output voltage noise DC ~ 10 kHz Vnoise mVpp 12 DC ~ 100 kHz 17 Accuracy @ 25℃ X % of I_pn -1 1 @ 25℃ Accuracy @ -40℃ ~ 105℃ X_TRange % of I_pn -2 2 -40℃ ~ 105℃
5 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
4. STK-32PL/A Electrical performance
Condition：T_A = 25℃ Vcc = 5 V (Except special instructions) Parameter Symbol Unit Min Typ Max Comment Primary nominal current rms I_pn A 32 Primary current measuring I_pm A -80 80 range Supply voltage Vcc V 4.75 5 5.25 Current consumption Icc mA 5 10 Reference voltage Vref V 2.48 2.5 2.52 Output function Rated output voltage V_FS V 0.8 (Vout - Vref )@ I_pn Internal output resistance R_out Ω 1 Output Internal output resistance R_ref Ω 1 Output Quiescent voltage Voff V 2.48 2.5 2.52 Vout @ 0 A Electrical offset voltage Voe mV -10 10 (Vout – Vref) @ 0 A Temperature drift of Voe Voe_TRange mV -8 8 -40℃ ~ 105℃ Magnetic offset current I_om A -0.25 0.25 @ ±10 x I_pn Theoretical gain G_th mV/A 25 800 mV @ I_pn Trimmed in the Error of gain Err_G %G_th ±0.5 factory @ 25℃ Temperature drift of gain G_TR %G_th -1.0 1.0 -40℃ ~ 105℃ Rated linearity error Non-L_pn %I_pn -0.5 0.5 ±I_pn Linearity error @ I_pm Non-L_pm %I_pm -1.0 1.0 ±I_pm Reaction time t_ra µs 0.5 1 @ 10% of I_pn Step response time t_res µs 1.5 2 @ 90% of I_pn Delay time t_delay µs 1 400 kHz sine wave Frequency bandwidth (-3dB) BW kHz 400 No RC circuit Output voltage noise DC ~ 10 kHz Vnoise mVpp 12 DC ~ 100 kHz 17 Accuracy @ 25℃ X % of I_pn -1 1 @ 25℃ Accuracy @ -40℃ ~ 105℃ X_TRange % of I_pn -2 2 -40℃ ~ 105℃
6 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
5. STK-40PL/A Electrical performance
Condition：T_A = 25℃ Vcc = 5 V (Except special instructions) Parameter Symbol Unit Min Typ Max Comment Primary nominal current rms I_pn A 40 Primary current measuring I_pm A -100 100 range Supply voltage Vcc V 4.75 5 5.25 Current consumption Icc mA 5 10 Reference voltage Vref V 2.48 2.5 2.52 Output function Rated output voltage V_FS V 0.8 (Vout - Vref )@ I_pn Internal output resistance R_out Ω 1 Output Internal output resistance R_ref Ω 1 Output Quiescent voltage Voff V 2.48 2.5 2.52 Vout @ 0 A Electrical offset voltage Voe mV -10 10 (Vout – Vref) @ 0 A Temperature drift of Voe Voe_TRange mV -8 8 -40℃ ~ 105℃ Magnetic offset current I_om A -0.25 0.25 @ ±10 x I_pn Theoretical gain G_th mV/A 20 800 mV @ I_pn Trimmed in the Error of gain Err_G %G_th ±0.5 factory @ 25℃ Temperature drift of gain G_TR %G_th -1.0 1.0 -40℃ ~ 105℃ Rated linearity error Non-L_pn %I_pn -0.5 0.5 ±I_pn Linearity error @ I_pm Non-L_pm %I_pm -1 1 ±I_pm Reaction time t_ra µs 0.5 1 @ 10% of I_pn Step response time t_res µs 1.5 2 @ 90% of I_pn Delay time t_delay µs 1 400 kHz sine wave Frequency bandwidth (-3dB) BW kHz 400 No RC circuit Output voltage noise DC ~ 10 kHz Vnoise mVpp 10 DC ~ 100 kHz 15 Accuracy @ 25℃ X % of I_pn -1 1 @ 25℃ Accuracy @ -40℃ ~ 105℃ X_TRange % of I_pn -2 2 -40℃ ~ 105℃
7 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
6. STK-50PL/A Electrical performance
Condition：T_A = 25℃ Vcc = 5 V (Except special instructions) Parameter Symbol Unit Min Typ Max Comment Primary nominal current rms I_pn A 50 Primary current measuring I_pm A -125 125 range Supply voltage Vcc V 4.75 5 5.25 Current consumption Icc mA 5 10 Reference voltage Vref V 2.48 2.5 2.52 Output function Rated output voltage V_FS V 0.8 (Vout - Vref )@ I_pn Internal output resistance R_out Ω 1 Output Internal output resistance R_ref Ω 1 Output Quiescent voltage Voff V 2.48 2.5 2.52 Vout @ 0 A Electrical offset voltage Voe mV -10 10 (Vout – Vref) @ 0 A Temperature drift of Voe Voe_TRange mV -8 8 -40℃ ~ 105℃ Magnetic offset current I_om A -0.25 0.25 @ ±10 x I_pn Theoretical gain G_th mV/A 16 800 mV @ I_pn Trimmed in the Error of gain Err_G %G_th ±0.5 factory @ 25℃ Temperature drift of gain G_TR %G_th -1.0 1.0 -40℃ ~ 105℃ Rated linearity error Non-L_pn %I_pn -0.5 0.5 ±I_pn Linearity error @ I_pm Non-L_pm %I_pm -1.5 1.5 ±I_pm Reaction time t_ra µs 0.5 1 @ 10% of I_pn Step response time t_res µs 1.5 2 @ 90% of I_pn Delay time t_delay µs 1 400 kHz sine wave Frequency bandwidth (-3dB) BW kHz 400 No RC circuit Output voltage noise DC ~ 10 kHz Vnoise mVpp 10 DC ~ 100 kHz 15 Accuracy @ 25℃ X % of I_pn -1 1 @ 25℃ Accuracy @ -40℃ ~ 105℃ X_TRange % of I_pn -2 2 -40℃ ~ 105℃
8 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
7. Output voltage VS primary current
The dependence of Vout of STK-10PL/A on the primary current.
The dependence of Vout of STK-20PL/A on the primary current.
9 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
The dependence of Vout of STK-32PL/A on the primary current.
The dependence of Vout of STK-40PL/A on the primary current.
10 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
The dependence of Vout of STK-50PL/A on the primary current.
8. Maximum continues DC current
The dependence of maximum continues current of STK-PL/A current on the working temperature.
11 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
9. Accuracy at room temperature
The distribution Voe of STK-PL/A current sensor at 25℃.
The distribution of V_FS OF STK-PL/A current sensor at 25℃.
12 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
10. Accuracy over temperature
The distribution of temperature drift of accuracy, compared with room temperature, over the temperature range from -40 deg.C to 105 deg.C.
The distribution of temperature drift of Voe, compared with room temperature, over the temperature range from -40 deg.C to 105 deg.C.
13 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
The distribution of temperature drift of GAIN, compared with room temperature, over the temperature range from -40 deg.C to 105 deg.C.
11. Frequency response and bandwidth
The frequency bandwidth of STK-PL/A series current sensor. The bandwidth of current sensor is DC ~ 400 kHz (-3dB).
14 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
12. Step response time
The typical frequency response of STK-xxPL/A current sensor. The response time from 90% of the primary current (light blue) to 90% of the secondary output (dark blue) is less than 1.5 μs
13. Frequency delay performance
When testing 400 kHz sine wave, the typical result of STK-xxPL/A current sensor’s output. The response time from the primary current (light blue) to the secondary output (dark blue) is less than 1 μs.
15 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
14. Recommended PCB layout
Installation of view: overlooking (unit: mm)
1. Installing angle：Overlook (observe from the side of installing transducer)
2. Recommended bore diameter of primary current line, (diameter of primary current × 1.2) mm 3. Recommended bore diameter of secondary current line, (diameter of secondary current × 1.2) mm 4. The maximum thickness of PCB is 2.5 mm 5. The curve of wave soldering: 260℃ × 10 s
Security： This current sensor must be used in limited-energy secondary circuit according to IEC 61010-1. This current sensor must be used in electric/electronic equipment with respect to appliance standards and safety requirement in accordance with the manufacture’s operating instructions; When operating the current sensor, certain parts of the module can carry hazardous voltage; Failure to wiring as shown in the diagram will damage the current sensor; Ignoring this warning can lead to serious consequences. A protective housing or a additional shield could be used. Main supply must be able to disconnected.
16 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
15. Dimension & Pin definitions
17 /18 Sinomags Technology http://www.sinomags.co m
STK-PL/A series current sensor
16. Appendix: typical application circuit
Theoretical -3dB Measured -3dB R3 (kohm) C3 (pF) f = 1/(2πRC) (kHz) (kHz) 20 20 398 ~ 400 20 81 98 ~ 100 20 810 10 ~ 10 The frequency characteristics of STK_PL/A series current sensor are not affected by the R-C setting (according to recommended R-C setting), therefore the active filter circuit or R-C circuit can be applied to modulate the sensor’s frequency characteristics. The signal input to ADC is 1.65+ R4/R2*(Vout-Vref) with the conditions: R1 = R2, R3 = R4, C3 = C4.
18 /18 Sinomags Technology http://www.sinomags.co m
