Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 28 views

    Deepak Torque Chart For A325

    Uploaded by

    Arun Prasad

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Deepak Torque Chart For A325

    Uploaded by

    Arun Prasad
    28 views1 page

    Original Title

    Deepak Torque Chart for A325

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    28 views1 page

    Deepak Torque Chart For A325

    Uploaded by

    Arun Prasad

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Metric Series :‐ Physical Properties‐Tightening Torque & Pretension as Per ASTM F3125/F3125M

    RECOMMENDED TORQUE VALUES FOR Grade A325M & A490 M HSFG WITH SURFACE FINISH BLACK OXIDE , ZINC PLATED &
    HOT DIP GALVANISED (TYPE‐1)

    Zinc Plated /Black Surface Finish


    S.No. Size (Diameter) Pre Tension (KN) STorque (Nm)
    Grade A325M Grade A490M Grade A325M Grade A490M
    (830 Mpa) (1040 Mpa) (830 Mpa) (1040 Mpa)
    1 M12 49.00 61 88.2 110
    2 M16 93.00 114 223.2 274
    3 M20 142.0 178 426.0 534
    4 M22 178.0 221 587.4 729
    5 M24 205.0 257 738.0 925
    6 M27 267.0 334 1081.4 1353
    7 M30 325.0 408 1462.5 1836
    8 M36 476.0 595 2570.4 3213
    Hot Dip Galvanised Surface Finish
    S.No. Size (Diameter) Pre Tension (KN) STorque (Nm)
    Grade A325M Grade A490M Grade A325M Grade A490M
    (830 Mpa) (1040 Mpa) (830 Mpa) (1040 Mpa)
    1 M12 49.00 61 70.56 87.8
    2 M16 93.00 114 178.56 218.9
    3 M20 142.0 178 340.80 427.2
    4 M22 178.0 221 469.92 583.4
    5 M24 205.0 257 590.40 740.2
    6 M27 267.0 334 865.08 1082.2
    7 M30 325.0 408 1170.00 1468.8
    8 M36 476.0 595 2056.32 2570.4
    Remarks:
    The value presented in the table are representative & have been compiled for the user benefit, Result can be
    influenced by no. of variable including.
    1. Inproper Lubrication 2. Nicked or binding Threads 3. Inadequate Torque control

    #User are recommender to apply Lubricant on nut Threads before use the assemblies
    The values of torque have been derived from the empirical formula.
    S torque (T) = K*D*P,for reference only should be calculated with actual conditions of assembely

    Where, K= Nut Factor or friction factor for calculation taken as 0.15, It varies with surface finish & Lubricant Quality
    P=Induced Load or Clamp Load or Pretension, which is 100% of Proof Load for Black Surface Finish & 80% of the Proof Load
    Value for HDG Surface Finish of assembely
    D= Nominal Thread Diameter of the Bolt

    Prepared By: Checked By: Approved By:


    Harsh Vardhan Rathore Akash Rathore P. Velmuthu
    Sr. Executive – Engineering Asst. manager‐ Engineering G.M‐ Operations

    You might also like