MOD5272

Ethernet Core Module

100 Version

DATASH EET
Key Points
• Use as a high-performance single board • Customize with a development kit and begin
computer or add Ethernet connectivity writing application code immediately!
to a new or existing design • Industrial temperature range (-40°C to 85°C)

Device Connectivity
• 10/100Mbps Ethernet • 3 PWM
• 2 UARTs and SPI • 16-bit address bus and 16-bit data
• SD/MMC flash card ready bus with 3 chip selects
• 29 digital I/Os

Performance and memory

• 32-bit 62.5 MHz Processor • 8MB SDRAM and 2MB Flash

Companion development kit

The following is available with the development kit:
• Customize any aspect of operation including web pages, data filtering, or custom network applications
• Development software: NB Eclipse IDE, Graphical debugger, deployment tools, and examples
• Communication software: TCP/IP stack, SSL/TLS 1.3, HTTP web server, FTP, E-mail, and flash file system
• System software: NBRTOS, ANSI C/C++ compiler and linker

Updated: November 7, 2023 | Page 1 of 7 © 2023 NetBurner Inc. All Rights Reserved.
 MOD5272

Specifications
Processor and Memory
32-bit Freescale ColdFire 5272 running at 62.5MHz with 8MB SDRAM and 2MB Flash

Network Interface
10/100 BaseT with RJ-45 connector (100 Version)

Data I/O Interface (J1 and J2)

• Up to 2 UARTs • 3 PWM
• Up to 29 digital I/O • SPI interface
• Up to 2 external timer in and up to 3 timer outputs • SD/MMC flash card ready
• Up to 4 external IRQs • 16-bit address bus and 16-bit data
bus with 3 chip selects

Flash Card Support

FAT32 support for SD Cards up to 8GB (requires exclusive use of SPI signals). Card types include SD/MMC (up to
2GB) and SDHC.

Serial Configurations
The UARTs can be configured in the following way:
• 2 TTL ports
• Add external level shifter for RS-232
• Add external level shifter for RS-422/485 (up to two ports)
Note: UART 0/1 also provides RTS/CTS hardware handshaking signals.

LEDs
Link and Speed (100 Version only, on RJ-45)

Physical Characteristics
Dimensions (inches): 2.60” x 2.00”
Mounting Holes: 2 x 0.125” dia

Power
DC Input Voltage: 3.3V @ 500mA typical

Environmental Operating Temperature

-40° to 85° C

RoHS Compliance
The Restriction of Hazardous Substances guidelines ensure that electronics are manufactured with fewer
environment harming materials.

Updated: November 7, 2023 | Page 2 of 7 © 2023 NetBurner Inc. All Rights Reserved.
 MOD5272

Part Numbers
MOD5272 Ethernet Core Module (100 Version, with RJ-45)
Part Number: MOD5272-100IR

MOD5272 Development Kit

Part Number: NNDK-MOD5272-KIT
Kit includes all the hardware and software you need to customize the included platform hardware. See NetBurner
Store product page for package contents. Note: Includes the MOD-DEV-100 development board.

Ordering Information
E-mail: sales@netburner.com
Online Store: www.NetBurner.com
Telephone: 1-800-695-6828

Updated: November 7, 2023 | Page 3 of 7 © 2023 NetBurner Inc. All Rights Reserved.
 MOD5272

Pinout and Signal Description

The module has two dual in-line 50 pin headers which enable you to connect to one of our standard NetBurner
Carrier Boards, or a board you create on your own. Table 1-2 provides descriptions of pin function of the module
header.
Table 1: Pinout and Signal Descriptions for J1 Connector (1)

J1 Connector
CPU Max
Pin Function 1 General Purpose I/O Description
Pin Voltage
1 GND Ground -
2 GND Ground -
3 VCC3V Input Power 3.3 VDC 3.3VDC
4 P14 R/W Read / NOT Write1 3.3VDC
5 K10 CS1 Chip Select 11,2 3.3VDC
6 P11 CS2 Chip Select 21,2 3.3VDC
7 N11 CS3 Chip Select 31,2 3.3VDC
8 P13 OE Output Enable1 3.3VDC
9 E12 BS2 Byte Strobe for D16 to D23 (8 bits)1 3.3VDC
10 E13 BS3 Byte Strobe for D24 to D31 (8 bits)1 3.3VDC
11 TIP Transfer in Progress1,2 3.3VDC
12 A5 D16 Data Bus - Data 16 3.3VDC
13 F3 TA PB5 Transfer Acknowledge1 3.3VDC
14 A6 D18 Data Bus - Data 18 3.3VDC
15 B6 D17 Data Bus - Data 17 3.3VDC
16 B7 D20 Data Bus - Data 20 3.3VDC
17 C7 D19 Data Bus - Data 19 3.3VDC
18 A8 D22 Data Bus - Data 22 3.3VDC
19 A7 D21 Data Bus - Data 21 3.3VDC
20 F12 D24 Data Bus - Data 24 3.3VDC
21 B8 D23 Data Bus - Data 23 3.3VDC
22 F14 D26 Data Bus - Data 26 3.3VDC
23 F13 D25 Data Bus - Data 25 3.3VDC
24 G13 D28 Data Bus - Data 28 3.3VDC
25 G12 D27 Data Bus - Data 27 3.3VDC

Note:
1. Active low signals, such as RESET, are indicated with an overbar.
2. The TIP signal is the logical AND of CS1, CS2 and CS3. TIP can be used to control an external data bus buffer for the data bus signals.
An example circuit design can be found on the Module Development Board schematic. An external data bus buffer is recommended for
any designs that use data bus signals D16 - D31.
3. J2-31 represents TIN0 and PB4/UART0 external baud rate clock. These two signals are tied together on the module PCB.
4. The ColdFire 5272 processor supports USB device mode only. A 48Mhz oscillator must be installed in locaton U8 of the Mod5272.

Updated: November 7, 2023 | Page 4 of 7 © 2023 NetBurner Inc. All Rights Reserved.
 MOD5272

J1 Connector (continued)
CPU Max
Pin Function General Purpose I/O Description
Pin Voltage
26 H14 D30 Data Bus - Data 30 3.3VDC
27 G14 D29 Data Bus - Data 29 3.3VDC
28 M12 RESET Processor Reset Input1 3.3VDC
29 H13 D31 Data Bus - Data 31 3.3VDC
30 F4 RSTOUT Processor Reset Output1 3.3VDC
31 CLK_OUT Clock Out (CLKOUT-62.5 MHz) 3.3VDC
32 D10 A0 Data Bus - Address 0 3.3VDC
33 B12 A1 Data Bus - Address 1 3.3VDC
34 A12 A2 Data Bus - Address 2 3.3VDC
35 A13 A3 Data Bus - Address 3 3.3VDC
36 A14 A4 Data Bus - Address 4 3.3VDC
37 B13 A5 Data Bus - Address 5 3.3VDC
38 B14 A6 Data Bus - Address 6 3.3VDC
39 C12 A7 Data Bus - Address 7 3.3VDC
40 C13 A8 Data Bus - Address 8 3.3VDC
41 C14 A9 Data Bus - Address 9 3.3VDC
42 D12 A10 Data Bus - Address 10 3.3VDC
43 C11 A11 Data Bus - Address 11 3.3VDC
44 B11 A12 Data Bus - Address 12 3.3VDC
45 A11 A13 Data Bus - Address 13 3.3VDC
46 C10 A14 Data Bus - Address 14 3.3VDC
47 D9 A15 Data Bus - Address 15 3.3VDC
48 VCC3V Input Power 3.3 VDC 3.3VDC
49 GND Ground -
50 GND Ground -

Note:
1. Active low signals, such as RESET, are indicated with an overbar.
2. The TIP signal is the logical AND of CS1, CS2 and CS3. TIP can be used to control an external data bus buffer for the data bus signals.
An example circuit design can be found on the Module Development Board schematic. An external data bus buffer is recommended for
any designs that use data bus signals D16 - D31.
3. J2-31 represents TIN0 and PB4/UART0 external baud rate clock. These two signals are tied together on the module PCB.
4. The ColdFire 5272 processor supports USB device mode only. A 48Mhz oscillator must be installed in locaton U8 of the Mod5272.

Updated: November 7, 2023 | Page 5 of 7 © 2023 NetBurner Inc. All Rights Reserved.
 MOD5272

Table 2: NetBurner MOD5272 Pinout and Signal Descriptions (4) for J2 Connector

J2 Connector
CPU General Purpose Max
Pin Function 1 Function 2 Description
Pin I/O Voltage
1 GND Ground -
2 VCC3V Input power 3.3 VDC 3.3VDC
3 H1 UART0_RX PB1 UART 0 Receive 3.3VDC
4 H4 UART0_TX PB0 UART 0 Transmit 3.3VDC
5 NC No Connect 3.3VDC
6 D11 PC14 Port C - Pin 14 3.3VDC
7 E11 PC13 Port C - Pin 13 3.3VDC
8 E10 PC15 Port C - Pin 15 3.3VDC
9 G11 PC11 Port C - Pin 11 3.3VDC
10 F11 PC12 Port C - Pin 12 3.3VDC
11 H11 PC10 Port C - Pin 10 3.3VDC
12 J13 PC9 Port C - Pin 9 3.3VDC
13 J12 PC8 Port C - Pin 8 3.3VDC
14 GND Ground -
15 L2 PC0 Port C - Pin 0 3.3VDC
16 L13 PC1 Port C - Pin 1 3.3VDC
17 K12 PC4 Port C - Pin 4 3.3VDC
18 L14 PC2 Port C - Pin 2 3.3VDC
19 K13 PC5 Port C - Pin 5 3.3VDC
20 K14 PC6 Port C - Pin 6 3.3VDC
21 K1 UART1_RX T0IN UART 1 Receive or Timer Input 0 3.3VDC
22 K4 UART1_TX T0OUT UART 1 Transmit or Timer Output 0 3.3VDC
23 K11 PC3 Port C - Pin 3 3.3VDC
24 J11 PC7 Port C - Pin 7 3.3VDC
25 L5 SPI_CLK BUSW1 SPI Clock or Bus Width Bit 1 3.3VDC

Note:
1. Active low signals, such as RESET, are indicated with an overbar.
2. The TIP signal is the logical AND of CS1, CS2 and CS3. TIP can be used to control an external data bus buffer for the data bus signals.
An example circuit design can be found on the Module Development Board schematic. An external data bus buffer is recommended for
any designs that use data bus signals D16 - D31.
3. J2-31 represents TIN0 and PB4/UART0 external baud rate clock. These two signals are tied together on the module PCB.
4. The ColdFire 5272 processor supports USB device mode only. A 48Mhz oscillator must be installed in locaton U8 of the Mod5272.

Updated: November 7, 2023 | Page 6 of 7 © 2023 NetBurner Inc. All Rights Reserved.
 MOD5272

J2 Connector (continued)
CPU General Purpose Max
Pin Function 1 Function 2 Description
Pin I/O Voltage
26 P1 SPI_CS3 T3OUT PA7 SPI Chip Select 3 or Timer Output 3 3.3VDC
27 P4 SPI_DIN SPI Data In 3.3VDC
28 N4 SPI_DOUT WSEL SPI Data Out or Bus Width Selection 3.3VDC
29 H2 UART0_CTS PB2 UART 2 Clear To Send1 3.3VDC
30 M5 SPI_CS0 BUSW0 SPI Chip Select 0 or Bus Width Bit 0 3.3VDC
L6 ,
31 T0IN UART0_CLK PB4 Timer Input 0 or UART 0 Clock3 3.3VDC
G3
32 N5 PWM0 PWM 0 Output Signal/Input Capture 3.3VDC
33 E2 USB_TXEN PA5 USB Transmit Enable 3.3VDC
34 P5 PWM1 TOUT1 PWM 1 Output Signal/Input Capture or Timer Output 1 3.3VDC
35 K2 SPI_CS2 UART1_CTS SPI Chip Select 2 or UART 1 Clear To Send 1
3.3VDC
36 M6 T0OUT PB7 Timer Output 0 3.3VDC
37 K6 PWM2 T1IN PWM 2 Output Signal/Input Capture or Timer Input 1 3.3VDC
38 H3 UART0_RTS PB3 UART 0 Request To Send1 3.3VDC
39 D2 USB_TP PA0 USB Transmit Serial Data 3.3VDC
40 L1 SPI_CS1 PA11 SPI Chip Select 1 3.3VDC
41 F2 USB_D- USB Line Driver Low 3.3VDC
42 D1 USB_RP PA1 USB Receive Serial Data 3.3VDC
43 M4 IRQ1 USB_WOR External Interrupt 11 3.3VDC
44 F1 USB_D+ USB Line Driver High 3.3VDC
45 N3 IRQ3 External Interrupt 31 3.3VDC
46 GND Ground -
47 K3 IRQ5 UART1_RTS External Interrupt 51 or UART 1 Request To Send1 3.3VDC
48 M3 IRQ6 PA15 External Interrupt 61 3.3VDC
49 GND Ground -
50 VCC3V Input Power 3.3 VDC 3.3VDC

Note:
1. Active low signals, such as RESET, are indicated with an overbar.
2. The TIP signal is the logical AND of CS1, CS2 and CS3. TIP can be used to control an external data bus buffer for the data bus signals.
An example circuit design can be found on the Module Development Board schematic. An external data bus buffer is recommended for
any designs that use data bus signals D16 - D31.
3. J2-31 represents TIN0 and PB4/UART0 external baud rate clock. These two signals are tied together on the module PCB.
4. The ColdFire 5272 processor supports USB device mode only. A 48Mhz oscillator must be installed in locaton U8 of the Mod5272.

Updated: November 7, 2023 | Page 7 of 7 © 2023 NetBurner Inc. All Rights Reserved.