etherpath

EtherPath
User’s Guide
Revised April 12, 2007

Firmware Version 7.0
FCC Statement
This device complies with the limits for a Class B digital device,
pursuant to Part 15 of the FCC rules. Operation is subject to the
following two conditions:
(1) This device may not cause harmful interference.
(2) This device must accept any interference received,
including interference that may cause undesired operation.
CE Marking Warning
This is a class B product. In a domestic environment this product

may cause radio interference in which case the user may be required
to take adequate measures.
RoHS Compliant
Copyright  1998…2007. All rights reserved.

Version 7.x
All trademarks and trade names are the properties of their respective
owners.
TABLE OF CONTENTS
FCC Statement........................................................ i
CE Marking Warning.............................................. i
RoHS Compliant..................................................... i
Chapter 1
Introduction.............................................................. 1
EtherPath Functions......................................................2
Client/Server Mode.......................................... 2
Server Mode.................................................... 3
Point-to-Multiple-Point (EtherModem) Mode. 3
Reverse Telnet (Telnet Client) Mode............... 3
Other Features.............................................................. 4
Automatic Connection............................................. 4
AT Commands......................................................... 4
Connection Recovery............................................... 4
Protocol Conversion................................................ 4
Configuration Security............................................. 5
Upgradeable Firmware............................................. 5
Physical Details............................................................ 6
Configuration Switch ............................................ 7
LED Indicators....................................................... 8
Package Contents...................................................9
Software Requirements..........................................9
Chapter 2
Installation.............................................................. 10
Overview.................................................................... 10
i
LAN Installation......................................................... 10
1. Connect the Network Cable............................. 10
2. Connect the Power Adapter Cable................... 11
3. Connect the Serial Port Device........................ 11
Chapter 3
Terminal/Telnet
Configuration.......................................................... 12
Overview.................................................................... 12
Terminal Configuration.............................................. 13
Procedure.............................................................13
Telnet Configuration.................................................. 14
Terminal/Telnet Interface...........................................16
Entering Data......................................................... 16
Menu Options...................................................... 17
Main Menu Option 1.
Setting IP Addresses............................................ 17
1. Local IP Address............................................... 18
2. Remote IP Address............................................ 18
3. Gateway IP Address........................................... 18
4. Subnet Mask...................................................... 18
5. Port Number...................................................... 18
6. IP Fragmentation............................................... 19
7. Operational Mode.............................................. 19
8. Ethernet Mode................................................... 19
7. TCP Tx Timeout................................................ 19
Main Menu Option 2.
Set Manager/Telnet IP Address............................ 20
Main Menu Option 3.
Set Serial Port Data.............................................. 21
ii
Introduction
Flow Control......................................................... 22
Baud Rate.............................................................. 22
Parity..................................................................... 22
Data Bits................................................................ 22
Stop Bits................................................................ 22
Pin 6 Control......................................................... 22
Dial Mode.............................................................. 22
RS-485 Mode........................................................ 23
Main Menu Option 4.
Advanced Configuration Screen.......................... 24
1. Transmit Timer.................................................. 25
M. Timer Mode..................................................... 25
2. Block Size.......................................................... 25
3. Flow Control OFF Buffer Level........................ 25
4. Flow Control ON Buffer Level.......................... 26
5. Line_Terminator_Character............................... 26
6. Transmit_on_LT_Char...................................... 26
7. Server End-of-Line Filter................................... 26
8. Client Local Character Echo.............................. 27
9. Keep-Alive Frequency...................................... 27
Main Menu Option 5.
Display Settings................................................... 28
Current Statistics............................................ 29
Network Packets Received .................................. 29
Network Packets Transmitted................................ 29
Network Packet Errors........................................... 29
Port Bytes Received............................................... 29
Port Bytes Transmitted.......................................... 30
Current Configuration.................................... 30
Switches Status...................................................... 30
iii
Current Connection IP Address............................. 30
Main Menu Option 6.
Reset Configuration to Default............................ 31
Main Menu Option 7.
Save and Exit....................................................... 31
Main Menu Option 8.
Security Configuration......................................... 31
Disable Web Configuration................................... 32
Disable Telnet Configuration................................. 32
Disable SNMP Agent............................................ 32
Set User ID and Password..................................... 32
Clear User ID and Password.................................. 32
Main Menu Option 9.
SNMP Configuration........................................... 33
Contact Person....................................................... 34
Device Name......................................................... 34
Physical Location.................................................. 34
SNMP Community................................................ 34
Main Menu Option 0.
Exit without Saving.............................................. 34
Chapter 4
Browser Configuration.......................................... 35
Overview.................................................................... 35
Connection Procedure................................................ 35
Web-based Interface...................................................37
Port Configuration Screen................................... 38
Flow Control......................................................... 38
Baud Rate.............................................................. 39
Parity..................................................................... 39
iv
Introduction
Data Bits................................................................ 39
Stop Bits................................................................ 39
Dial Mode.............................................................. 39
RS-485 Mode (Displayed only if jumpered for RS-485)......39
Port Activity Screen.............................................40
Advanced Configuration Screen..........................41
Transmit Timer...................................................... 42
Timer Mode........................................................... 42
Block Size.............................................................. 43
Flow Control OFF Buffer Level............................ 43
Flow Control ON Buffer Level.............................. 43
Line_Terminator_Character................................... 43
Transmit_on_LT_Char.......................................... 43
Server End-of-Line Filter....................................... 44
Client Local Character Echo.................................. 44
Keep-Alive Frequency........................................... 44
LAN Configuration Screen..................................45
Local IP Address................................................... 45
The IP address of this EtherPath device on your LAN. The
default IP Address is 192.168.1.1 ......................... 45
Subnet Mask.......................................................... 45
Gateway IP Address............................................... 46
If the remote EtherPath (in “Client/Server” mode) is not on
the same LAN, then the gateway to the other LAN must be
entered here........................................................... 46
Ethernet Mode....................................................... 46
Remote Device IP Address.................................... 47
Remote (Listen) IP Port Number........................... 47
IP Fragmentation................................................... 47
Port Number.......................................................... 47
v
IP Fragmentation................................................... 48
TCP Tx Timeout.................................................... 48
SNMP Configuration Screen............................... 49
Contact Person....................................................... 49
Device Name......................................................... 50
Physical Location.................................................. 50
SNMP Community Name...................................... 50
Configuration Summary Screen...........................51
Chapter 5
Operation................................................................ 52
Client/Server Point-to-Point (Nailed-Up) Mode....... 52
Server Mode............................................................... 54
Client/Server Point-to-Multiple-Point (EtherModem) Mode.. 54
Client (Reverse Telnet) Mode.................................... 57
Method 1 (ATD dial mode)................................... 57
Method 2 (Hardware Dial mode)........................... 58
Chapter 6................................................................. 59
Configuration Security........................................... 59
Overview.................................................................... 59
Level 0: ....................................................................60
Level 1:.......................................................................60
Level 2:.......................................................................61
Level 3:.......................................................................61
Chapter 7
Troubleshooting...................................................... 63
Hardware Problems.................................................... 63
vi
Introduction
Can't Connect via the LAN........................................65
Other Problems...........................................................67
Checking Device Operation....................................... 69
Appendix A
Specifications.......................................................... 70
EtherPath Specifications.............................................70
RS-232 PIN Assignments...........................................71
Control Signal Operation............................................72
DCD...................................................................... 72
Receive Data.......................................................... 72
Transmit Data........................................................ 72
DTR....................................................................... 72
Signal Ground........................................................ 72
DSR....................................................................... 72
RTS....................................................................... 73
CTS....................................................................... 73
Ring Indicator........................................................ 73
CABLES.....................................................................74
To PC 9-pin COM: port................................. 74
SR Mux Composite or Access Switch Input Port......... 74
SS-1 to Modem.............................................. 75
Specialty Cables............................................. 75
Ethernet Cross-Over Cable............................ 75
Appendix B
Programming.......................................................... 76
Introduction................................................................ 76
Description and Behavior...........................................77
vii
Ports used by the EtherPath................................. 77
Server Mode........................................................ 78
Transmit Conditions.............................................. 78
Locking Avoidance Mechanism........................... 79
When in Raw Server mode:................................... 79
Application Notes.......................................................80
Appendix C
AT Command Summary........................................ 81
AT Commands............................................................81
AT Command Responses........................................... 82
AT Command Operation ........................................... 82
Appendix D
RS-422/ RS-485 Interface....................................... 83
Introduction................................................................ 83
Changing the Setting............................................83
RS-422 / 4-Wire RS-485 Interface Pinout................. 84
2-Wire RS-485 Interface Pinout.................................85
viii
Chapter 1
Introduction
This chapter provides an overview of the
EtherPath's features and capabilities.
C ongratulations on the purchase of your new EtherPath. The

EtherPath is a versatile product that enables serial
communications devices to operate via Ethernet. It is designed to
easily connect a serial port device to your network. A remote PC or
other serial device can then be used to monitor, configure, manage
and send or receive data to the serial port device through the
LAN/WAN.
The EtherPath can receive data from any Serial device, convert the
data to a valid IP packet, and transmit that data over the
LAN/WAN. Serial devices can then be accessed from anywhere on
your LAN/WAN by any workstation computer running telnet,
dedicated software, or COM: port redirection software. Two
EtherPaths may be used in “nailed-up” mode to build a “RS-232
path” through the WAN/LAN. Multiple EtherPaths may be
connected via Ethernet by using them in Point-to-Multiple point
"AT Dial " mode.
Some serial port devices in common use are Bar Code Readers,
UPSs, SCADA RTUs, security alarms, access control devices, time
clocks, POS terminals, and multiplexers.
For easy connection to your LAN, the EtherPath supports both
10BaseT and 100BaseT connections.
1
EtherPath User’s Guide
EtherPath Functions
The EtherPath can be used in several modes – simple Client/Server
or Server, as illustrated below, point-to-multiple-point
(EtherModem) Client/Server, and reverse telnet Client. These
modes are described below.
Figure 1: Modes of Operation
Client/Server Mode
In this mode, two EtherPaths are used. Both are connected to serial
RS-232 devices. This is termed a “Nailed-Up” connection.
• The "Client" EtherPath will automatically establish a
connection to the "Server" EtherPath upon power-up.
• The device on one EtherPath communicates with the other
serial port device as if it was directly connected via a serial port
cable.
Introduction
• The EtherPaths and the LAN are completely transparent to PC
application and serial port device.
Server Mode
This mode requires only a single EtherPath. The EtherPath is
connected to the serial port device, and to the LAN.
Users on the LAN can then connect to the serial port device and
communicate with it via Telnet, using any assigned IP and port
address. Most LAN connected workstations provide support for
communication via Telnet.
A special-purpose utility program or port redirector program may be
used instead of Telnet, or the user may create custom software using
Visual Basic, C++, or other network programming tools. By using
port redirection, the EtherPath may function as a remote serial port
on a PC.
Point-to-Multiple-Point (EtherModem) Mode

Point-to-multiple-point (EtherModem) operation allows a single
EtherPath running in client mode to connect to multiple server-
mode EtherPaths, one at a time, under the control of the attached
RS-232 device. The client operates similar to a modem with “AT”
dialing enabled. The attached device treats the EtherPath as if it
was a modem, using remote IP addresses instead of telephone
numbers.
Reverse Telnet (Telnet Client) Mode

This mode requires only a single EtherPath. The EtherPath is
connected to the serial port device, and to the LAN.
The EtherPath will connect to most remote telnet servers under user
control by using “reverse telnet” or telnet client operation. The
3
EtherPath will connect to any port number under user control with
either hardware (pin6) dialing or AT dialing.
By using the "AT Dial" commands, the connected device can direct
the EtherPath to connect to multiple remote devices, one at a time.
Other Features
Automatic Connection
When used in Client/Server mode, the “Client” EtherPath will
automatically establish a connection to the “Server” EtherPath on
power-up, or under the control of an RS-232 control signal.
AT Commands
The EtherPath responds to most common AT commands when in
the Client mode. Commands are listed in the Appendix.
Connection Recovery
The EtherPath uses a proprietary protocol to ensure the client/server
session always exists on TCP/IP. When data hasn't been transferred
through the connection for some time, the EtherPath will
communicate with the other device (either EtherPath or PC) to
ensure that the connection is still open.
If there is no response, the device will reset to the initial state, and
attempt to reconnect.
Also, if the RS-232 link is broken, it will be reconnected
automatically if possible (when in Hardware-connect mode).
This operation is described in the Appendix.
Protocol Conversion
The RS-232 device at the client end and the device at the server end
of a link do not have to use the same communications protocols on
Introduction
the RS232 link (speed, parity, flow control). The EtherPaths will
convert the data to the correct protocol.
Configuration Security
Etherpath configuration may be “Locked-down” or restricted in
several ways. The web Browser interface, telnet configuration
interface, and SNMP configuration interfaces may be disabled.
Specific IP addresses may be configured into the unit to disallow
configuration from any other than the desired management
workstations.
Upgradeable Firmware
Firmware upgrades are downloadable to the EtherPath. The utility
program required for this, and the actual firmware upgrades, are
available from your dealer.
5
Physical Details
The EtherPath front and rear panels are shown below.
Figure 1: EtherPath
Figure 2: EtherPath
Introduction
Configuration Switch
There is a momentary action push button switch on the rear of the
unit behind a small hole. Pressing this switch places the unit in
configuration mode and is used only when configuring the
EtherPath via the serial port, as explained in Chapter 3 -
Configuration. Return from configuration mode by exiting the
configuration menu or by power cycling the unit. This switch may
be depressed with a tiny screw driver or stiff wire. (A straightened
paper clip works nicely). Pressing the switch does not return the
unit to factory defaults. To return to factory defaults, use any
configuration method and select “Set To Defaults” as the command.
7
LED Indicators
There are three LED indicators on the top panel.
• The leftmost LED indicates the unit's current mode. Solid =
Server; Off = Client, Flashing= Setup Condition.
• The second LED indicates the status of the LAN interface. If it
is on, there is a valid LAN connection, Off indicates no LAN
connection, and flashing indicates activity on a valid lan
connection. A valid LAN connection means a connection from
another EtherPath or some other device... not merely being
plugged into a hub or switch.
• The right most LED flashes along with activity on the RS-232
port.
Introduction
Package Contents
You should find the following items packaged with your EtherPath:
• The EtherPath Unit
• Power Adapter (typical)
• This User’s Guide
If any of the above are missing, contact your dealer immediately.
Software Requirements
The EtherPath supports the following protocols.
• TCP/IP
• UDP
• ARP
• ICMP
• TELNET
• SNMP
• AT-Dial
The EtherPath has been tested to work with:

• All versions of Windows
• Unix - SCO, Sun, AIX, Linux, etc.
• Macintosh
• Most serial devices such as scanners, RTUs, SCADA
hosts, alarm controllers, POS devices, PCs, terminals, etc.
• VOIP multiplexers, digital video cameras, video
conferencing systems, etc.
9
Chapter 2
Installation
This Chapter details the LAN installation process
for the EtherPath.
Overview
For Telnet Mode or Web Browser Mode configuration, LAN
installation is performed before configuration. There must also be a
valid IP address in the unit prior to configuration with these
methods. The default IP address may not work with your
network.
If you use Terminal Mode configuration, then the configuration
should be performed prior to LAN installation. See Chapter 3 for
details.
LAN Installation
1. Connect the Network Cable

• The EtherPath network interface is auto-sensing. Simply
connect your network cable to the appropriate connector on the
EtherPath panel.
10
Configuration
2. Connect the Power Adapter Cable
Plug in the power adapter cable. After about a four second boot
process the EtherPath is ready for operation.
Only use the power adapter provided
with the EtherPath. Using a different
one may cause hardware damage.
3. Connect the Serial Port Device

Connect the serial port device to the serial port on the EtherPath. If
connecting to a PC 9-pin port, a cross-over (null modem) cable
is required. See the Appendix for wiring details.
Then apply power lead to the serial port device.
11
Chapter 3
Terminal/Telnet
Configuration
This Chapter describes how to configure the
EtherPath's using Terminal configuration mode or
Telnet configuration mode. Web Browser mode is
covered in the next chapter.
Overview
The EtherPath can be configured using any of the following
methods:
• Web Browser - After installing the EtherPath in your LAN,
use your Web Browser for configuration. See Chapter 4 -
Browser Configuration for details.
• Terminal Mode - Use a serial cable connection and a
communication program. The advantage of this method is that
you give the EtherPath a compatible IP Address prior to
installation in your network.
• Telnet Mode - After installing the EtherPath in your LAN,
connect to it using Telnet for configuration.
Both Terminal and Telnet modes provide the same user interface.
12
Operation
Terminal Configuration
Terminal configuration requires the following:
• PC with terminal emulation program, or a dumb terminal.
• Serial cable to connect the PC to the EtherPath. See the
Appendix for cable requirements. A Crossover (null modem)
cable is required when using a 9 pin PC port.
Procedure
1. Connect the EtherPath to your PC or terminal using a null-
modem cable.
2. Press the configuration setup switch momentarily. It is located
on the side of the EtherPath and accessed through a small hole.
Use a small pen or paper clip to access the switch.
3. Start the terminal program and configure the terminal program
with the following settings.
Setting Value
Flow control protocol None
Baud rate 9600
Data 8 bits
Parity None
Stop Bit 1
4. Connect your terminal program to the appropriate port (e.g.
COM 1).
13
5. The configuration program should now start and after a few
seconds display a sign-on screen.
If nothing appears on your screen, press the Enter key.
Refer to Terminal/Telnet Interface on page 16 for details on
using the configuration program.
Telnet Configuration
1. Install the EtherPath into your LAN as described in Chapter 2.
Ensure that the EtherPath is powered on. The EtherPath must
have an IP address appropriate for YOUR network.
2. Connect to the EtherPath with your telnet program. An
example command might be:
telnet IP_Address Port_number
Where:
IP_Address is the IP address of the EtherPath
Port_number (for configuration) is 8000.
For example, if the default IP address had not been changed,
then you would enter the command:
telnet 192.168.1.1 8000
If you can't connect

If the EtherPath does not respond, check the following:
• The EtherPath is properly installed, LAN connections
are OK, and it is powered ON.
• Check that your PC is using a compatible IP Address
and Network Mask.
In Windows9x variations, the IP Address and Network
Mask can be checked by using Control Panel-Network
14
Operation
to examine the Properties for the TCP/IP protocol.
• If your PC is NOT using an IP Address within the range
192.168.1.2 to 192.168.1.254, with a Network Mask of
255.255.255.0, then you must either change the
EtherPath's IP address using a directly connected
terminal or change your PC to an address in the above
range and reboot. Once the PC will communicate with
the EtherPath, the EtherPath address may be changed,
and the PC reconfigured to its proper address.
3. Refer to the following section for details on using the

configuration program.
15
Terminal/Telnet Interface
The Signon screen displays the version number.
EtherPath V5.3
--------------------------------
Device Name: GW0000B0
Physical Location: Head Office
Operational Mode: SERVER
Configuration setup.
[Press any key to continue]
Pressing any key will then take you to the Main Menu.
EtherPath Main Menu

------------------------------------------
1 Set Local & Remote IP Address,
Subnet Mask, and Gateway Address
2 Set Manager/Telnet IP Address
3 Serial Port Configuration
4 Advanced Configuration
5 Display Configuration Settings
6 Reset Configuration to Default
7 Save and Exit
8 Security Configuration
9 SNMP Configuration
0 Exit without Saving
Choose a Number =>
Each of these menu options is explained in the following pages.

Entering Data
Enter the number of the field you wish to change, followed (on the
same line) by a space and the data for that field.
For example: On screen one, to set the IP address (field 1) to
192.168.1.10
=> 1 192.168.1.10
16
Operation
Menu Options
Main Menu Option 1.
Setting IP Addresses
Selecting 1 ( 1.
Set Local & Remote IP Address, Subnet
Mask, Gateway Address ) from the Main Menu will result in a
screen which looks like the following.
LOCAL UNIT CONFIGURATION:

Local Address: 205.166.54.216 Serial NO:
00:09:AA:00:00:B0
Remote Address: (NOT SET)
Gateway Address: (NOT SET) Subnet Mask:
255.255.255.0
Server Mode - Listen on Port: 3000
IP Fragmentation: ALLOWED
Ethernet Mode: Auto
TCP Tx Timeout: ENABLED
SET LOCAL UNIT CONFIGURATION:
1 Local IP Address
2 Remote IP Address
3 Gateway IP Address
4 Subnet Mask
5 Port Number
6 IP Fragmentation [0=ALLOWED, 1=NOT ALLOWED]
7 Operational Mode [0=Server, 1=Client,
2=Telnet Server, 3=Telnet Client]
8 Ethernet Mode [0=Auto, 1=100Mb-Full, 2=100Mb-
Half, 3=10Mb-Full, 4=10MB-Half]
9 TCP Tx Timeout [0=Enabled, 1=Disabled]
0 -- Return to previous menu
Enter Command =>
17
1. Local IP Address
The IP address of this EtherPath device on your LAN. The default
IP Address is 192.168.1.1
2. Remote IP Address
In “Client” mode, this is the IP address of the remote “Server”
device which this client will automatically connect to when powered
up (if RS-232 PIN 6 is high or forced) and configured for hardware
dialing. This is also the default server that will be used for AT
dialing when in PMP mode.
In “Server” mode, this value is not required, and will be ignored.
3. Gateway IP Address
If the remote device this unit communicates with is not on the same
LAN, then the gateway to the other LAN must be entered here.
4. Subnet Mask
The network mask indicates what class of TCP/IP network you
have. The default value is for a class “C” network, with up to 255
users. This value should work in small networks. If in doubt, consult
your network administrator.
5. Port Number
This is the TCP/IP port number the EtherPath listens on when in
server mode. The default is port 3000. When in client mode, this is
the port on the remote server that a connection is attempt with. This
value may be overridden when in Ethermodem mode by including a
port number in the ATD command.
18
Operation
6. IP Fragmentation
If set to ZERO, IP blocks sent from this EtherPath may be
fragmented in transit, and blocks may be fragmented by the
EtherPath. If set to ONE, the 'DONTFRAG' bit is set in IP packets,
and all blocks are transmitted intact. This is normally set to 0 , but
is set to 1 for some SCADA applications. The default is 0.
7. Operational Mode
Server and Client modes provide a raw data path and should be
selected when two EtherPaths are used in a nailed up configuration.
This is often named “raw sockets” mode and is transparent to the
data being transported.
Telnet Server and Telnet Client modes perform Telnet command
processing and should be used when an EtherPath is communicating
directly with a Host Telnet Client or Server.
8. Ethernet Mode
The EtherPath ethernet interface may be configured as 10Mbps or
100Mbps, half or full duplex; or AUTO. The default of AUTO is
most commonly used. If hard configured, insure that the hub or
switch matches the mode selected.
7. TCP Tx Timeout
When enabled, the local unit will close the connection if it is unable
to deliver data to the remote unit. The timeout is dependent upon the
round-trip time, but will be in the range of 5 to 12 minutes. When
disabled, the unit will try forever to deliver the data.
19
Main Menu Option 2.
Set Manager/Telnet IP Address
Selecting (2) from the Main Menu will result in the following
screen.
Entry Manager_IpAddr
***** ***************
1. 000.000.000.000
2. 000.000.000.000
3. 000.000.000.000
4. 000.000.000.000
MANAGER SETUP:
set Entry_Number IP_Address
clear Entry_Number
0 --Return to main menu.
EXAMPLE:
to set entry #3 to IP address=138.239.0.24,
=> set 3 138.239.0.24
to clear entry #2 IP address,
=> clear 2
Enter Command =>

This screen shows a table containing four (4) entries. By default, all
entries are blank. These entries provide a security feature. Only a
user at one of the IP addresses shown can configure the EtherPath.
(All users on the LAN can still access the EtherPath, but not
configure it.)
If the entries are blank, then any user on the LAN can configure
the EtherPath. If you are not sure about using this feature,
leave the addresses all zeros.
Entries in the table cannot be edited, but commands are provided to
insert (SET) and delete (CLEAR) entries.
20
Operation
Main Menu Option 3.
Set Serial Port Data
Selecting (3) from the Main Menu will result in the following
screen.
PORT CONFIGURATION:
Flow Control: NONE
Baud Rate: 9600
Data: 8 Bits Parity: NONE Stop: 1 Bit
Pin 6 Control: FORCED ON
Client Dial Mode: HARDWARE (Pin 6)
RS485: 4-wire (Jumpers set for RS232)
SET PORT CONFIGURATION:

1 Flow Control [0=None, 1=XON/XOFF, 2=RTS/CTS, 3=RTS
Toggle]
2 Baud Rate [0=230400, 1=115200, 2=57600, 3=38400,
4=19200,
5=9600, 6=4800, 7=2400, 8=1200,
9=600, 10=300]
3 Parity bit [0=None, 1=Odd, 2=Even]
4 Data bits [0=7bits, 1=8bits]
5 Stop bits [0=1bit, 1=2bits]
6 Pin 6 Control [0=From Interface, 1=Forced ON]
7 Dial Mode [0=ATD, 1=Hardware (Pin 6)]
8 RS485 Mode [0=4-wire, 1=2-wire]
0 -- Return to previous menu.
EXAMPLE: To set the baud rate to 19200

=> 2 4
Enter Command =>
This screen allows you to change the settings for the RS232 link.
The settings used should match the device connected to the serial
port of the EtherPath.
Note that the EtherPath's serial settings must match the device that
is plugged into THAT EtherPath. The device at the other end of the
Ethernet link may be set differently.
21
Flow Control
The choices are “None”, “XON/XOFF”, and “RTS/CTS”. It is
common to use NONE for installation troubleshooting, then set it
correctly to match the connected device. If RTS/CTS is used, the
cables must have handshake lines wired correctly. RTS Toggle is a
handshake mode commonly used with half duplex modems. The
RTS output is asserted when the unit has data to transmit and it will
remain asserted for approximately 5ms after the last character has
been transmitted. The CTS signal controls output flow.
Baud Rate
Speeds between 300 bps and 230.4Kbps are supported.
Parity
The choices are “None”, “Odd”, or “Even”.
Data Bits
The choices are 7 or 8. This does NOT include the parity bit. The
two most common settings are 7 bit PLUS appropriate parity or 8
bit with NO parity. Default is 8 bits.
Stop Bits
The choices are 1 or 2. Commonly use 1.
Pin 6 Control
If Forced On, the EtherPath responds as if interface pin 6 is always
high. If From Interface, its condition is a read from the RS-232
cabling must be correct for proper operation.
Dial Mode
The choices are “ATD” or “Hardware”. This configures the
EtherPath, when in client mode, to connect to a remote device when
it receives an asserted hardware (pin 6) signal or when it receives
22
Operation
an “ATD” command. For a full-time Nailed-up connection, use
Hardware. See Chapter 5, Point-to-Multiple-Point-Mode for use of
the "AT" setting.
RS-485 Mode
Select between 4-wire full duplex and 2-wire half duplex RS-485
mode. For RS-485 operation, the hardware jumpers inside the unit
must be moved from the RS232 to the RS485 position. This setting
is ignored when using RS-232.
23
Main Menu Option 4.
Advanced Configuration Screen
Selecting (4) from the Main Menu will display the following:
ADVANCED CONFIGURATION:
Transmit Timer: 10 ms (Mode: IDLE TIMEOUT)
Block Size: 512 Bytes
Flow OFF Buffer Level: 80% Flow ON Buffer
Level: 20%
Line Terminator Character: 13 (Dec) Transmit on LT
Char: OFF
Server End-of-Line Filter: ON
Client Local Character Echo: OFF
Keep-Alive Frequency: 0 seconds
SET ADVANCED CONFIGURATION:

1 Transmit Timer [min=1ms, max=10000ms]
M Timer Mode [0=transmit timer, 1=idle timeout]
2 Block Size [min=1byte, max=4096bytes]
3 Flow Control OFF Buffer Level [min=1%, max=99%]
4 Flow Control ON Buffer Level [min=1%, max=99%]
5 Line Terminator Character [min=0, max=255]
6 Transmit on LT Character [0=OFF, 1=ON]
7 Server End-of-Line Filter [0=OFF, 1=ON]
8 Client Local Character Echo [0=OFF, 1=ON]
9 Keep-Alive Frequency [0=OFF, 1-32767 seconds]
EXAMPLE: To set the Flow OFF level to 75%

=> 3 75
Enter Command =>

The EtherPath has a built-in buffer to store data. Most of these
settings affect the operation of the buffer and how data is buffered
and transmitted over the Ethernet. The default values should
normally be satisfactory, but they may be "tuned" for optimum
operation.
Note: Options 5, 6, 7, and 8 apply to Client Mode only, and have no
effect in Server Mode.
24
Operation
1. Transmit Timer
When in Timer Mode: The time period for which data will be
stored in the buffer before being sent. Allowable values range from
1ms to 10,000ms (10 seconds). A commonly used value is 20 msec.
When in Idle Timeout Mode: The time period this unit's port must
be idle (after receiving a character) before sending a block of data
via the Ethenet. This is used to keep incoming blocks of data intact.
It is useful for some protocols such as Modbus RTU. Its setting
depends upon the port speed, and should be several character times..
Allowable values range from 1ms to 10,000msec (10 seconds). A
typical value for a 9.6 Kbps port is about 3 msec.
M. Timer Mode
When set to 0, the timer is a free-running clock and if there is data
in the buffer, an IP packet is transmitted every TIMER msec.
When set to 1, the timer is a serial port idle time value. If there is
data in the buffer and the serial port has been idle for TIMER msec,
then an IP packet is transmitted.
2. Block Size
The maximum ethernet packet buffer size. The minimum value is 1
byte, the maximum 4096 bytes (4 K). Typical values are either in a
low range of 10-20 characters for polling applications or very large
in the range of 500 to 1500 for file transfer applications.
Normally, the timer triggers a packet transmission before the block
fills. If the buffer contains BLOCKSIZE characters, an IP packet is
transmitted regardless of the timer mode and settings.
3. Flow Control OFF Buffer Level
If the amount of data stored in the buffer reaches this point, and the
EtherPath is unable to transmit the data, then no further input will be
accepted.
25
Under normal operation, this will not happen. This is normally left
at the default value.
4. Flow Control ON Buffer Level
Once the High_Water mark has been reached, the “no-input
accepted” mode will continue until the EtherPath has transmitted
enough data to reduce the buffer contents to this point. This is
normally left at the default value.
5. Line_Terminator_Character
This setting is used to change the Line Terminator Character. The
Line Terminator Character causes any data in the buffer to be
transmitted immediately the character is received, provided: This is
the binary value of the trigger charaacter.
• The EtherPath is being used in “Client” mode.
• The following setting (Transmit_on_LT_Char) is ON.
6. Transmit_on_LT_Char
When this setting is ON, any data in the buffer will be sent
immediately upon receipt of a Line_Terminator_Character (see
previous setting). When the setting is OFF, the
Line_Terminator_Character has no effect.
In “Server” mode, this setting has no effect.
7. Server End-of-Line Filter
This setting can turn the filter function ON or OFF.
If ON, then when a CR/LF (Carriage Return, Line Feed) character
pair is received, it is converted to a CR only before it is sent to the
serial port output. CR/LF pairs are normally used in the MS-DOS
environment to mark the end of a line, but may cause problems in
other environments.
CR/NULL character pairs are also converted to a CR only.
26
Operation
• If this setting is OFF, then no conversion is done.
• In "Client Mode", this setting has no effect.
8. Client Local Character Echo
If ECHO is ON, the client EtherPath will locally echo all incoming
characters in client mode.
If ECHO is OFF, the client EtherPath will not echo characters or
transmit any status messages to the serial port. This mode should be
used if any messages from the EtherPath would create interference.
OFF is the most commonly used value.
9. Keep-Alive Frequency
Setting this parameter to a non zero value will enable a Keep-Alive
feature in the Unit. When the Unit is in Client or Telnet Client
mode, it will send Keep-Alive messages to the server at the
specified frequency when the link between the client and server is
idle. When the Unit is in Server or Telnet Server mode, it will close
the connection if the link is idle for more than 3.5 times the Keep-
Alive Frequency. [0=OFF, 1-32767 seconds]
27
Main Menu Option 5.
Display Settings
Selecting (5) from the Main Menu displays a screen like the
following example.
LOCAL UNIT CONFIGURATION:
Local Address: 205.166.54.216 Serial NO:
00:09:AA:00:00:B0
Remote Address: (NOT SET)
Gateway Address: (NOT SET) Subnet Mask:
255.255.255.0
Server Mode - Listen on Port: 3000
IP Fragmentation: ALLOWED
Ethernet Mode: Auto
TCP Tx Timeout: ENABLED
SNMP CONFIGURATION:
Name of Contact Person: Supervisor
SNMP Community: public
MANAGER CONFIGURATION:
Entry Manager_IP_Addr
***** ***************
1. 0.0.0.0
2. 0.0.0.0
3. 0.0.0.0
4. 0.0.0.0
PORT CONFIGURATION:
Flow Control: NONE
Baud Rate: 9600
Data: 8 Bits Parity: NONE Stop: 1 Bit
Pin 6 Control: FORCED ON
Client Dial Mode: HARDWARE (Pin 6)
RS485: 4-wire (Jumpers set for RS232)
ADVANCED CONFIGURATION:
Transmit Timer: 20 ms (Mode: TRANSMIT TIMER)
Block Size: 512 Bytes
Flow OFF Buffer Level: 80% Flow ON Buffer
Level: 20%
Line Terminator Character: 13 (Dec) Transmit on LT
Char: OFF
28
Operation
Server End-of-Line Filter: OFF
Client Local Character Echo: OFF
Keep-Alive Frequency: 0 seconds
CURRENT ETHERPATH STATISITCS:
Network packets received: 12
Network packets transmitted: 8
Network packet errors: 0
Port bytes received: 4
Port bytes transmitted: 0
CURRENT ETHERPATH CONFIGURATION:

SERVER Mode
Connected to IP Address: (NO ACTIVE CONNECTION)
[Press any key to continue]
Note that no data can be changed. Pressing any key from the above
screen will return you to the Main Screen.
All data items except the following have been explained on the
preceding pages.
Current Statistics
Network Packets Received

Number of packets received by the EtherPath through the LAN
connection.
Network Packets Transmitted
Number of packets transmitted by the EtherPath through the
LAN connection.
Network Packet Errors
Number of packets received through the LAN connection which
contained errors.
Port Bytes Received
Number of Characters received through the serial (RS232)
connection.
29
Port Bytes Transmitted
Number of Characters transmitted through the serial (RS232)
connection.
Current Configuration
Switches Status
Current setting of the DIP Switches.
Current Connection IP Address
The IP address of thedevice (PC, terminal, or remote
EtherPath) to which the EtherPath is currently connected
through the LAN link. If it is not connected, this field will
display “No active connection”.
30
Operation
Main Menu Option 6.
Reset Configuration to Default
Selecting (6) from the Main Menu will restore all values to their
defaults.
If using Telnet, the connection will be lost when the EtherPath
reboots. To reconnect, you must connect to the default IP Address
of 192.168.1.1 or change the EtherPath IP address to one that is
appropriate for your network before rebooting with main menu
option 7.
Main Menu Option 7.

Save and Exit
Selecting (7) from the Main Menu will store the configuration
details in the EtherPath, and exit the configuration program.
If using Telnet, the connection will be lost when the EtherPath
reboots. If you have changed the IP Address, you must use the new
IP Address when you reconnect.
Using option 7 when there were no changes made is one way to
effect a cold reboot on a remote EtherPath.
Main Menu Option 8.

Security Configuration
Selecting (8) from the Main Menu will display the security
configuration screens.
31
SET SECURITY CONFIGURATION:

1 Disable Web Configuration [0=ENABLED, 1=DISABLED]
2 Disable Telnet Configuration [0=ENABLED, 1=DISABLED]
3 Disable SNMP Agent [0=ENABLED, 1=DISABLED]
4 Set User ID and Password [index userid password]
5 Clear User ID and Password
EXAMPLE: To set User ID 1 to root, password toor
=> 4 1 root toor
Enter Command =>
Set Security Configuration Screen

Disable Web Configuration
The web configuration may be turned off. If set to disabled, the unit
will not answer to web browser inquires.
Disable Telnet Configuration

If disabled, the unit will not answer telnet connection requests on
port 8000, and the only configuration method will be direct terminal
connection
Disable SNMP Agent

If disabled, the unit will not respond to SNMP traps and gets
Set User ID and Password

Used to establish user names and passwords.
Clear User ID and Password

Clears existing user names and passwords
The EtherPath uses the industry standard IP protocol. Since this is a

well known standard, its security vulnerabilities are also well known
and may be exploited. Several EtherPath options are available to
32
Operation
enhance the inherent security of your EtherPath network. However,
since network security is a moving target and absolute security is
never achievable, every network installation should be designed and
implemented with care to minimize security risks in a way that is
appropriate for the application and perceived risks.
The EtherPath may be configured with several levels of security
configuration and authentication. These restrict the ability of an
unwanted user from changing the configuration of the EtherPathl.
They do not restrict the ability of a remote device to deliver packets
to the EtherPath's data port.
Before starting configuration security, you should be familiar with
the information in chapter 5.
Main Menu Option 9.

SNMP Configuration
Selecting (9) from the Main Menu will display the SNMP
configuration screen.
SNMP CONFIGURATION:
Name of Contact Person: Supervisor
SNMP Community: public
SET SNMP CONFIGURATION:

1 Name of Contact Person
2 Device Name
3 Physical Location
4 SNMP Community
Enter Command =>
33
Contact Person
This text field can be used to store the name of the person
responsible for the Serial Port Device.
Device Name
This can be used to store a descriptive name for the device.
Physical Location
This can be used to store he location of the device.
SNMP Community
The SNMP community name. Default is “public”.
Main Menu Option 0.

Exit without Saving
Selecting (0) from the Main Menu will exit the configuration
program without saving any data you have entered.
If you changed the IP address, this will force the unit to restart using
the new address.
34
Operation
Chapter 4
Browser Configuration
This Chapter describes how to configure the
EtherPath using a Web Browser. The EtherPath
must have an IP address appropriate to your
network before using this method.
Overview
This configuration method uses your Web Browser to configure the
EtherPath. This provides the most user-friendly interface than the
Telnet/Terminal method.
• The EtherPath must be installed in your LAN before this
configuration method can be used.
• Most Browsers will work. The only requirement is that they
support HTML tables and forms.
Connection Procedure
To establish a connection to the EtherPath, follow this procedure:
1. Install the EtherPath in your LAN as described in Chapter 2.

Ensure that the EtherPath is powered on.
4. Start your Web browser.
5. In the Address box, enter the following:
http://IP_Address
35
(IP_Address is the IP address of the EtherPath)
For example, http://192.168.1.1
If you can't connect
If the EtherPath does not respond, check the following:
• The EtherPath is properly installed, LAN connections
are OK, and it is powered ON.
• Check that your PC is using a compatible IP Address
and Network Mask.
In Windows9x variations, the IP Address and Network
Mask can be checked by using Control Panel-Network
to examine the Properties for the TCP/IP protocol.
• If your PC is NOT using an IP Address within the range
192.168.1.2 to 192.168.1.254, with a Network Mask of
255.255.255.0, then you must either change the
EtherPath's IP address using a directly connected
terminal or change your PC to an address in the above
range and reboot. Once the PC will communicate with
the EtherPath, the EtherPath address may be changed,
and the PC reconfigured to its proper address.
• Insure that your browser isn't using a proxy server. If it
is, configure the browser to not use the proxy for the
EtherPath's IP address. (This may not work in Internet
Explorer and you might have to temporarily disable
using the proxy server)
6. Once connected, you will see the first screen. Refer to the
following section for details on using the Web-based interface.
36
Operation
Web-based Interface
The first screen is similar to Figure 2.
Figure 2: Sign on Screen

• Use the menu bar on the left to navigate to the desired screen.
• On-line help is available on each screen.
• Each screen is explained in the following sections.
37
Port Configuration Screen
Figure 3: Port Configuration Screen
This screen allows you to change the settings for the RS232 link.
The settings used should match the device connected to the serial
port of the EtherPath.
Note that the EtherPath's serial settings must match the device that
is plugged into THAT EtherPath. The device at the other end of the
Ethernet link may be set differently.
Flow Control
The choices are “None”, “XON/XOFF”, and “RTS/CTS”. It is
common to use NONE for installation troubleshooting, then set it
correctly to match the connected device. If RTS/CTS is used, the
RS-232 cables must have handshake lines wired correctly. RTS
Toggle is a handshake mode commonly used with half duplex
modems. The RTS output is asserted when the unit has data to
38
Operation
transmit and it will remain asserted for approximately 5ms after the
last character has been transmitted. The CTS signal controls output
flow.
Baud Rate
Speeds between 300 bps and 230.4Kbps are supported.
Parity
The choices are “None”, “Odd”, or “Even”.
Data Bits
The choices are 7 or 8. This does NOT include the parity bit. The
two most common settings are 7 bit PLUS appropriate parity or 8
bit with NO parity.
Stop Bits
The choices are 1 or 2. Commonly use 1.
Dial Mode
The choices are “ATD” or “Hardware”. This configures the
EtherPath, when in client mode, to connect to a remote device when
it receives an asserted hardware (pin 6) signal or when it receives
an “ATD” command. For a full-time Nailed-up connection, use
Hardware. See Chapter 5, Point-to-Multiple-Point-Mode for use of
the "AT" setting.
RS-485 Mode (Displayed only if jumpered for RS-485)
Select between 4-wire full duplex and 2-wire half duplex RS-485
mode. For RS-485 operation, the hardware jumpers inside the unit
must be moved from the RS232 to the RS485 position. This setting
is ignored when using RS-232.
39
Port Activity Screen
Figure 4:Port Activity Screen
This screen displays details about the data currently being

transmitted or received, either through the LAN or Serial port. The
display is updated every 10 seconds.
Data - Network
Current
The IP Address of the remote to device to which
Connection
this EtherPath is currently connected
IP Address:
Packets Number of packets received by the EtherPath
received: through the LAN connection including
management screen packets.
40
Operation
Packets Number of packets transmitted by the EtherPath
Transmitted through the LAN connection, including
management screen updates.
Packet Errors Number of packets containing errors transmitted
or received by the EtherPath through the LAN
connection.
Under normal conditions, this should be 0.
Data - Serial Port

Bytes Number of Bytes received, through the serial
Received (RS232) connection, from the Serial port device
Bytes Number of Bytes transmitted through the serial
(RS232) connection to the Serial port device (or
Transmitted
PC, if in Client mode).
Advanced Configuration Screen
Figure 5: Advanced Configuration Screen
41
The EtherPath has a built-in buffer to store data. Most of these
settings affect the operation of the buffer and how data is buffered
and transmitted over the Ethernet. The default values should
normally be satisfactory for most installations, but they may be
"tuned" for optimum operation.
Note: Options 5, 6, 7, and 8 apply to Client Mode only, and have no
effect in Server Mode.
Transmit Timer
When in Timer Mode: The time period for which data will be
stored in the buffer before being sent. Allowable values range from
1ms to 10,000ms (10 seconds). A commonly used value is 20 msec.
For example, in this mode, every 20 msec, the buffer will be
transmitted if there is any data in it.
When in Idle Timeout Mode: The time period this unit's serial
port must be idle (after receiving a character) before sending a block
of data via the Ethenet. This is used to keep incoming blocks of
data intact. It is useful for some protocols such as Modbus RTU.
Its setting depends upon the port speed, and should be several
character times.. Allowable values range from 1ms to 10,000msec
(10 seconds). A typical value for a 9.6 Kbps port is about 3 msec.
For example, in this mode, if there is data in the buffer and 3 msec.
passes with no additional data being received, the buffer is
transmitted.
Timer Mode
When set to 0, the timer is a free-running clock and if there is data
in the buffer, an IP packet is transmitted every TIMER msec.
When set to 1, the timer is a serial port idle time value. If there is
data in the buffer and the serial port has been idle for TIMER msec,
then an IP packet is transmitted.
42
Operation
Block Size
The maximum Ethernet packet buffer size. The minimum value is 1
byte, the maximum 4096 bytes (4 K). Typical values are either in a
low range of 10-20 characters for polling applications or very large
in the range of 500 to 1500 for file transfer applications.
Normally, the timer triggers a packet transmission before the block
fills. If the buffer contains BLOCKSIZE characters, an IP packet is
transmitted. This setting is rarely changed from the default.
Flow Control OFF Buffer Level
If the amount of data stored in the buffer reaches this point, and the
EtherPath is unable to transmit the data, then no further input will be
accepted.
Under normal operation, this will not happen. This is normally left
at the default value.
Flow Control ON Buffer Level
Once the High_Water mark has been reached, the “no-input
accepted” mode will continue until the EtherPath has transmitted
enough data to reduce the buffer contents to this point. This is
normally left at the default value.
Line_Terminator_Character
This setting is used to change the Line Terminator Character. The
Line Terminator Character causes any data in the buffer to be
transmitted immediately the character is received, provided: This is
the binary value of the trigger character.
• The EtherPath is being used in “Client” mode.
• The following setting (Transmit_on_LT_Char) is ON.
Transmit_on_LT_Char
When this setting is ON, any data in the buffer will be sent
immediately upon receipt of a Line_Terminator_Character (see
43
previous setting). When the setting is OFF, the
Line_Terminator_Character has no effect.
In “Server” mode, this setting has no effect.
Server End-of-Line Filter
This setting can turn the filter function ON or OFF.
If ON, then when a CR/LF (Carriage Return, Line Feed) character
pair is received, it is converted to a CR only before it is sent to the
serial port output. CR/LF pairs are normally used in the MS-DOS
environment to mark the end of a line, but may cause problems in
other environments.
CR/NULL character pairs are also converted to a CR only.
• If this setting is OFF, then no conversion is done.
• In "Client Mode", this setting has no effect.
Client Local Character Echo
If ECHO is ON, the client EtherPath will locally echo all incoming
characters in client mode.
If ECHO is OFF, the client EtherPath will not echo characters or
transmit any status messages to the serial port. This mode should be
used if any messages from the EtherPath would create interference.
OFF is the most commonly used value.
Keep-Alive Frequency
Setting this value to a non-zero value will enable a Keep-Alive
feature in the unit. When the unit is in Client or Telnet Client mode,
It will send Keep-Alive messages to the server at the specified
frequency if there is no other traffic on the link .
The default is normally appropriate, but for low-bandwidth links,
the keep-alive packets may be sent less often. In rare cases, it is
turned off by setting the value to zero.
44
Operation
LAN Configuration Screen
Figure 6: LAN Configuration Screen
This screen allows you to set all data relating to your LAN.
Local IP Address
The IP address of this EtherPath device on your LAN. The
default IP Address is 192.168.1.1
Subnet Mask
The network mask indicates what class of TCP/IP network you
have. The default value is for a class “C” network, with up to 255
users. This value should work in small networks. If in doubt, consult
your network administrator.
45
Gateway IP Address
If the remote EtherPath (in “Client/Server” mode) is not on the same
LAN, then the gateway to the other LAN must be entered here.
Mode
Server and Client modes provide a raw data path and should be
selected when two EtherPaths are used in a nailed up configuration.
This is often named “raw sockets” mode and is transparent to the
data being transported.
Telnet Server and Telnet Client modes perform Telnet command
processing and should be used when an EtherPath is communicating
directly with a Host Telnet Client or Server.
Ethernet Mode
Although most often used in auto-configure mode, the EtherPath
may be forced to 10Mbps, 100Mbps, half, or full duplex. This
option is useful when connected to a switch that is very slow
powering up. The EtherPath powers up fairly quickly, and may be
forced to a compatible mode to prevent it from negotiating an
invalid configuration with a hub or switch that isn’t initialized to
negotiate.
Administrator Access Rights
If the entries are blank, then any user on the LAN may
configure the EtherPath. If you are not sure about using this
feature, leave the addresses all zeros.
This screen shows a table containing four (4) entries. By default, all
entries are blank. These entries provide a security feature. Only a
user at one of the IP addresses shown can configure the EtherPath.
(All users on the LAN can still access the EtherPath, but not
configure it.) Read the security chapter before implementing this
feature.
46
Operation
Remote Device IP Address

In “Client” mode, this is the IP address of the remote “Server”
device which this client will automatically connect to when powered
up (if RS-232 PIN 6 is high or forced) and configured for hardware
dialing. This is also the default server that will be used for AT
dialing when in PMP mode.
In “Server” mode, this value is not required, and will be ignored.
Remote (Listen) IP Port Number

the port on the remote server that a connection is attempted with.
This value may be overridden when in Ethermodem mode by
including a port number in the ATD command. See Appendix B for
a discussion of the sending IP port number.
IP Fragmentation
Port Number
the port on the remote server that a connection is attempt with. This
value may be overridden when in Ethermodem mode by including a
port number in the ATD command.
47
IP Fragmentation
TCP Tx Timeout
When enabled, the local unit will close the connection if it is unable
to deliver data to the remote unit. The timeout is dependent upon the
round-trip time, but will be in the range of 5 to 12 minutes. When
disabled, the unit will try forever to deliver the data. This is
normally used in the default enabled mode. It is sometimes turned
off to operate better with satellite Internet provider TCP ACK
spoofing.
48
Operation
SNMP Configuration Screen
Figure 7: SNMP Configuration Screen
Overview
This screen may be ignored if SNMP is not used.
These are text fields, commonly used in SNMP (Simple Network
Management Protocol) Programs to identify this device when
browsing the network.
Other standard MIB values are returned to the SNMP manager
along with this information.
Contact Person
This text field can be used to store the name of the person
responsible for the Serial Port Device.
49
Device Name
This can be used to store a descriptive name for the device.
Physical Location
This can be used to store he location of the device.
SNMP Community Name
The SNMP community name. The default is “public”.
50
Operation
Configuration Summary Screen
Figure 8:Configuration Summary Screen
Operation
• This screen displays all current settings for this EtherPath
• Clicking the "Set to Defaults" button will restore ALL
values to their factory default values.
When this is done, the EtherPath will reboot, and the
existing connection will be lost. You must reconnect using
the default IP Address of 192.168.1.1.
51
Chapter 5
Operation
This Chapter explains how to use the EtherPath,
once it is installed and configured. Although it
may be used with automated equipment such as
RTUs, POS, or other computer-based devices; the
example configurations shown in this chapter use
terminals or terminal emulation on a PC for
illustrations. It is often useful to set up the
EtherPath using this method before connecting
other equipment.
Client/Server Point-to-Point (Nailed-Up)

Mode
• Both EtherPaths must be correctly installed and configured as
described in Chapters 3 or 4. One serial port device is
connected to the “Server” EtherPath, and another serial device
is connected to the “Client” EtherPath. One EtherPath has the
operational mode set as a "Server", the other has the
operational mode set as a "Client".
• The communication settings for the serial devices must be the
same as the values entered into the EtherPath device they each
attach to.
• Power up the "server" EtherPath.
• Power up the "client" EtherPath. It will automatically connect
to the remote EtherPath whose IP address was stored during
52
Operation
configuration if hardware dialing is enabled and pin 6 is
asserted.
• You may now proceed as if the remote serial port device was
directly connected to the serial port of your local serial device.
• If Pin 6 control is set to From Interface, then the serial device
must provide a high level signal on pin 6 before the EtherPath
will accept or place an Ethernet connection.
53
Server Mode
• Install and connect the EtherPath and Serial Port Device as
described in Chapters 3 and 4.
• Any PC or workstation on the LAN/WAN should now be able
to use Telnet to connect to the Serial Port Device with the
command:
telnet IP_Address Port_number
Where IP_Address is the IP address of the EtherPath, and
Port_number is the configured value (default value is 3000).
For example, if the default IP address and port number have not
been changed (and they are appropriate for your network), then
you would enter the command:
telnet 192.168.1.1 3000
• You should see a “Connected” message from the telnet client
when the connection is established. Some telnet clients don’t
display this message.
connected to the serial port of your PC or workstation.
• If there is a firewall in the link between the EtherPath and your
workstation, you may need to configure it to pass packets using
the port number configured into the EtherPath.
Client/Server Point-to-Multiple-Point
(EtherModem) Mode
• EtherModem mode requires multiple EtherPaths configured in
“Server” mode and a single EtherPath configured in “Client”
54
Operation
mode. Under user control with "AT" commands, the “Client”
connects to multiple “Servers”, one at a time similar to the way
a dial-up modem would. "Server" and "Client" refer to the
operational mode settings of the EtherPath.
• All EtherPaths must be connected as described in Chapters 3
and 4. One serial port device is connected to each “Server”
EtherPath, and additional serial devices (usually a workstation)
are connected to the “Client” EtherPaths.
• The “Client” EtherPath must be configured for “ATD” dialing.
This is the unit that will place the calls to the other EtherPaths.
• At the “Client” end, start the Terminal emulation program (or
use a real terminal). The communication settings for this device
must be the same as the values entered into the “Client”
EtherPath device earlier.
• Power up the local EtherPath. It will be in command mode,
awaiting a connection command. Type the command “AT
<enter>” to test the RS-232 connection. It should answer with
an “OK” message. If not, check the serial port rate and wiring
connections. “Dial” a remote EtherPath by using an “ATD”
dial command.. “ATD1.2.3.4:5555” , where 1.2.3.4 is the IP
address of the remote EtherPath and 5555 is the optional
connection port number configured in the remote EtherPath.
The EtherPath will automatically connect to the remote
EtherPath. If an address isn’t given, the IP address stored
during configuration is used. If a port isn’t given, the port
number stored during configuration is used.
• Upon establishing a connection, a “Connect” message is
displayed. If unable to establish a connection a “Busy”
message is displayed.
connected to the serial port of your workstation.
55
• Disconnect from that remote EtherPath with either the “+++”
command followed by “ATH” or by lowering the hardware lead
on pin six.
• See the Appendix for a complete list of AT commands and
responses.
56
Operation
Client (Reverse Telnet) Mode

Method 1 (ATD dial mode)
• The EtherPath must be configured for “ATD” dialing and set
for "client".
• Start the Terminal emulation program (or use a real terminal).
The communication settings for this device must be the same as
the values entered into the “Client” EtherPath device earlier.
• Power up the local EtherPath. It will be in command mode,
awaiting a connection command. Type the command “AT
<enter>” to test the RS-232 connection. It should answer with
an “OK” message. If not, correct the RS-232 cable miswiring
or terminal program problem. “Dial” a remote telnet server by
using an “ATD” dial command.. “ATD1.2.3.4:5555” , where
1.2.3.4 is the IP address of the remote telnet server and 5555 is
the optional connection port number configured in the remote
telnet server. The EtherPath will automatically connect to the
remote telnet server. If an address or port number isn’t given,
the values stored during configuration are used. See the
Appendix for a complete list of "AT" commands and
responses.
• If the EtherPath is in “Client - Echo” mode, you should see the
message “Connect OK !” from the client mode EtherPath when
the connection is established
• You may now proceed as if the remote telnet server was
• Disconnect from that remote telnet server with either the “+++”
command or by lowering the hardware lead on pin six.
57
Method 2 (Hardware Dial mode)

• This mode operates with the “Hardware dial (Pin 6 ) setting. In
this mode, the EtherPath connects to the configured IP address
as soon as RS-232 pin 6 is asserted.
• The EtherPath must be configured for “Hardware(Pin 6)”
dialing and dip switches set for "client".
• Start the Terminal emulation program (or use a real terminal).
The communication settings for this device must be the same as
the values entered into the “Client” EtherPath device earlier.
• Power up the local EtherPath. The EtherPath will automatically
connect to the remote telnet server using the values stored
during configuration.
• If the EtherPath is in “Client - Echo” mode, you should see the
message “Connect OK !” from the client mode EtherPath when
the connection is established
• You may now proceed as if the remote telnet server was
• Disconnect from that remote telnet server by lowering the
hardware lead on pin six.
58
Operation
Chapter 6
Configuration Security
This section discusses configuration options that
restrict configuration.
Overview
The EtherPath uses the industry standard IP protocol. Since this is a
well known standard, its security vulnerabilities are also well known
and may be exploited. Several EtherPath options are available to
enhance the inherent security of your EtherPath network. However,
since network security is a moving target and absolute security is
never achievable, every network installation should be designed and
implemented with care to minimize security risks in a way that is
appropriate for the application and perceived risks.
The EtherPath may be configured with several levels of security
configuration and authentication. These restrict the ability of an
unwanted user from changing the configuration of the EtherPathl.
They do not restrict the ability of a remote device to deliver packets
to the EtherPath's data port.
At the level 0, any workstation may be used to configure the
EtherPath via either telnet or web browser configuration. Level 1
restricts configuration to workstations claiming to be from one of
four IP addresses previously stored in the EtherPath. Either web-
based or telnet configuration is allowed. Level 2 disables remote
configuration using web browser, telnet, or SNMP in any
combination. Level 3 requires a user name and password for remote
59
configuration. Combinations of Level 2 and Level 3 are possible
(ie. One may disable web browser configuration and SNMP and
require a username/password for telnet configuration. The most
secure method would be to disable all remote configuration.
The EtherPath may always be configured using the direct connected

terminal method. This requires physical access to the hardware, and
pressing the configuration button while a terminal (or PC) is
connected to the serial port.
Level 0:
No specific security configuration is required. Make sure that no IP
addresses have been entered in menu item 2, "Set Manager/Telnet
IP Address" screen (or the "Administrator Access Rights of the web
browser "Configure LAN" screen). Also, any user name/password
pairs that may have been entered on the terminal
configuration/telnet "Security Configuration" screen should be
cleared.
Level 1:
Using any configuration method, configure Administrator Access IP
addresses. Enter the IP addresses that should have the ability to
change the EtherPath configuration. If configuring this remotely,
insure that the workstation you are using is one of the valid
addresses.
60
Operation
Level 2:
Using telnet or direct connection configuration, selectively enable
or disable remote configuration via Telnet, via web browser, and
SNMP. This setting may not be performed from the web
configuration screen.
Level 3:
Configure Level 1 and Level 2 security as needed. Using the telnet
or direct connection configuration, enter up to three user name and
password pairs. If there is at least one user name in this list, then a
password prompt will be issued upon establishing a telnet
configuration session.
There may be up to 3 user names and passwords configured. If no

users are configured, password protection is disabled. User names
and passwords are limited to 8 characters each. There is a six failed
login attempt limit. After six failed attempts in a row, the unit will
lock out all logins for a period of about 10 minutes.
Each user name has an associated user ID or index. The user with
ID 1 is considered the master user. It has the ability to change the
other user names and passwords. The other two user ID's are
limited to only changing their own user name and password. All
users may modify any other system parameters.
61
The serial interface is not subjected to user login since it
requires physical access to the unit.
SECURITY CONFIGURATION:
Web Configuration: ENABLED

Telnet Configuration: ENABLED
SNMP Agent: ENABLED
Index UserName Password
----- -------- --------
1:
2:
3:
SET SECURITY CONFIGURATION:
1 Disable Web Configuration [0=ENABLED, 1=DISABLED]
2 Disable Telnet Configuration [0=ENABLED, 1=DISABLED]
3 Disable SNMP Agent [0=ENABLED, 1=DISABLED]
4 Set User ID and Password [index userid password]
5 Clear User ID and Password
EXAMPLE: To set User ID 1 to root, password toor

=> 4 1 root toor
Enter Command =>
Security Configuration Screen
62
Chapter 7
Troubleshooting
This chapter outlines some problems that may
occur during installation operation and some
possible solutions to them.
If you follow the suggested troubleshooting steps and the EtherPath

still does not function properly, please contact your dealer for
further advice.
Hardware Problems
Before anything else, check that all cables used are wired
correctly and properly connected.
If connecting to a 9 pin PC port, a crossover (null

modem) cable is required.
P1: All the EtherPath’s LEDs are off.

S1: Check the power supply or power connection.
P2: When using 10Base-T cabling, the EtherPath unit does not
work.
S2: Check the Hub’s link LED for the port to which theEtherPath is
connected. If it is off, make sure the network cable between the
EtherPath and hub is in good condition. You may only use one
of the LAN connections at a time. Make sure the Hub supports
63
10BaseT or 100BaseT. Sometimes it helps to move the
network cable to a different hub port or power cycle the hub
(especially when using smart hubs or Ethernet switches).
64
Troubleshooting
Can't Connect via the LAN
P1: Can't connect to the EtherPath using Telnet or Web Browser.

S1: Check the following:
• Start troubleshooting from a known state. Power the
EtherPath and other equipment OFF and ON to reboot.
• “Ping” the EtherPath to see if it responds. From the
Windows command prompt or “Run” dialog box, use the
command:
ping IP_Address
Where IP_Address is the IP Address of the EtherPath
(e.g. ping 192.168.1.1 ). If it does not respond, then
check all LAN connections. If the workstation can not
ping the EtherPath, nothing else will work… fix this first.
If the LAN connection are OK, the problem is in the LAN
addresses or routing. You should be able to ping both
EtherPaths in a Client/Server pair.
• If using a LAN without routers, you can connect to the
EtherPath ONLY IF your PC and the EtherPath are using
IP Addresses from the same address block. The EtherPaths
default IP Address (192.168.1.1) requires that your PC is
using an address from the address block 192.168.1.2 to
192.168.1.254, and a Network Mask of 255.255.255.0. If a
router is between the devices, a gateway address must be
configured in both devices.
Check your PC's IP Address using Control Panel -

Network - TCP/IP (Adapter) Properties or similar
commands appropriate for your computer. If you are using
a different Address block, use Terminal Mode
65
configuration to set a compatible IP Address in the
EtherPath.
• Check that you have used the correct port address. The
default address is “3000” for normal operation and “8000”
for configuration.
• Is there a firewall in the Ethernet path. If so, it must be
configured to pass the ports in use by the EtherPath. Many
trouble calls are the result of firewall changes that block
the EtherPath ports.
• Are you trying to connect to the EtherPath data port with a
web browser? That only works for configuration on port
8000.
• Web Browsers often are configured to use a proxy server.
The browser might need to be configured to NOT use the
proxy when connecting to the EtherPath, or the proxy
server may be configured to pass the requests correctly.
• MOST EtherPath connection problems are due to incorrect
RS-232 wiring. The second most common errors are
incorrect IP addressing on either the EtherPath or on the
PC used for testing.
66
Troubleshooting
Other Problems
P1: Can’t run the configuration program using a serial cable

connection.
S1: Check that:
• You did press the configuration button.
• The communication parameters are set properly.
• Disconnect and reconnect the power supply to the
EtherPath.
• Power is available... a LED is on.
• The most common problems causing this symptom are
incorrect RS-232 wiring or the Windows Hyperterm
program not operating correctly.
P2: The “Client” EtherPath doesn’t automatically connect to the

“Server” EtherPath.
S2: Check that:
• One unit is configured as a client, the other as a server. For
troubleshooting, note that the DTR signal is asserted as
soon as a connection is active.
• The “Client” is configured for automatic connections.
“Hardware (Pin 6) Dial” is the correct setting.
• The “Client” should either be configured for “Pin 6
Control” forced ON or the interface must be wired in such
a way that that pin 6 is asserted.
• The “Server’s” IP address was correctly entered into the
“Client’s” EtherPath in the “Remote IP Address” field.
• The Gateway IP Address is set correctly.
• The Subnet Mask is set correctly.
67
• The communication parameters between the PC/terminal
and the local (“Client”) EtherPath match.
• The communication parameters between the serial port
device and the remote (“Server”) EtherPath match.
P5: The EtherPath's IP Address is unknown. Is there any way of

finding it?
S5: Follow this procedure:
• Yes, see the chapter on using Terminal Configuration.
• Press the configuration button and use a terminal
connection to read the existing configuration.
P6: Why does the "Server Mode" EtherPath close the TCP/IP
connnection to the "Client Mode" EtherPath (or other client
program).
S6: The "Server Mode" EtherPath will disconnect the link if it does
not receive any packets from the "Client Mode" EtherPath (or
other client program) within a 3 minute period or if hardware
pin 6 is lowered. See Appendix B for more details. The Keep-
Alive frequency configuration value affects this operation.
P7: The connection works, but is too slow.
S7: If in Transmit timer mode, lower the transmit timer to send
packets more frequently. 20 to 30 msec. is a good range for
many users. If in Idle timeout mode perhaps the serial data rate
may be increased so characters arrive at the EtherPath faster.
68
Troubleshooting
Checking Device Operation
Once the EtherPath is installed on your Network, you can connect to
it using Telnet, to verify its operation. The procedure is as follows.
1. Leave the EtherPath in its normal operating mode.
7. Use telnet to connect to the EtherPath with the command:
telnet IP_Address 8000
Where IP_Address is the IP Address assigned to the
EtherPath, and 8000 represents the Port number.
• The port number is “8000” for configuration, but “3000” is
the default for normal operation.
• If the “Manager IP Addresses” have been entered in the
EtherPath, then only a PC having one of those addresses
can change the configuration.
8. Choose item 5 (“Display Settings”) from the Main Menu, and
examine the data shown. See Chapter 3 for an explanation of
each of the data items.
69
Appendix A
Specifications
EtherPath Specifications
• Flash Memory: 512 Kbytes
• SDRAM: 512 Kbytes
• EEPROM: 512 Bytes
• LAN Buffer: 2 Kbytes
• RS-232/RS-485 Buffer: 4 Kbytes
• RS-232/RS-485: one male DE-9 connector
• Network: Ethernet 10Base-T/ 100Base-T
• CPU: 16 Bit
• Power: 5 to 30 VDC (200 ma at 12 VDC) or Optional power
supplies
• Switch: Configuration
• LED: 3 multi-purpose
• Default IP address: 192.168.1.1
• Default Receive port: 3000
70
Specifications
RS-232 PIN Assignments

The EtherPath RS-232 port wiring is identical to a standard PC 9
pin DE-9P COM: port. It operates as a DTE device. The chart
below details signal directions and names.
Serial Port Pin Assignments

Pin Signal Name Type
1 Carrier Detect (CD) In
2 Receive (Rx) In
3 Transmit (Tx) Out
4 Data Terminal Ready Out
5 Signal Ground (GND) Power
6 Data Set Ready (DSR) In
(Hardware controlled-
connection input. See Section
5)
7 Request to Send (RTS) Out

8 Clear to Send (CTS) In
9 Ring Indicator (RI) (Not used) In
71
Control Signal Operation

DCD
Input, ignored
Receive Data
Input, data into the EtherPath
Transmit Data
Output, Data from the EtherPath. The EtherPath only transmits
when it has characters to send and it is not flowed-off with
XON/XOFF or RTS/CTS flow control.
DTR
Output. Signal is enabled when the EtherPath has a valid LAN
connection to another device. This signal is low when powered on.
It goes high when a valid LAN connection is established, and
returns to low when that connection is disconnected.
Signal Ground
Common ground
DSR
Input. Used for connection control. If the EtherPath is configured
for “Hardware (Pin 6) Dial” and not “Forced ON”, the EtherPath
connects to a remote device via the LAN when the signal is
asserted. If configured for “Forced ON” and “Hardware (Pin 6)
Dial”, the EtherPath connects to the remote device upon power up.
If configured for “AT Dial”, and “From Interface”, the input must
be asserted before the AT Dial command will create a connection.
On units configured as a server, DTR must be high before an
incoming connection will be established.
72
Specifications
RTS
Output. Input flow control. When the internal buffer reaches the
“Flow Off” buffer level, this signal is lowered. When the buffer
level decreases to the “Flow ON” buffer level, this signal is raised.
CTS
Input. When Flow Control is set for CTS/RTS, lowering this signal
will halt data flow from the EtherPath RS-232 port.
Ring Indicator
Not used
73
CABLES
Commonly used cable connections:
To PC 9-pin COM: port
S S -1 PC
1,6 4
2 3
3 2
4 1,6
5 5
7 8
8 7
This is a relatively common null-modem PC crossover

cable
SR Mux Composite or Access Switch Input Port
RJ-45 DE-9S
1 BLU N/C
2 ORG N/C
3 BLK 4,1,6
4 RED 5
5 GRN 2
6 YEL 3
7 BRN 8
8 WHT 7
74
Specifications
SS-1 to Modem
Use any commercially available PC-to-modem cable.
Specialty Cables
For special devices (RTUs, POS terminals, etc. contact technical
support or check the DCB web site technical support section. DCB
will assist in designing special cables at no cost, or provide proven
cable solutions at a reasonable cost.
Ethernet Cross-Over Cable

Used to connect two EtherPath Ethernet connections “back-to-back”
without using an Ethernet hub for test purposes. Also used to
connect a EtherPath directly to a PC’s LAN connection for testing.
RJ-45 RJ-45
1 WHT / ORG 3
2 ORG / WHT 6
3 WHT / GRN 1
4 BLU / WHT N/C
5 WHT / BLU N/C
6 GRN / WHT 2
7 WHT / BRN N/C
8 BRN / WHT N/C
75
Appendix B
Programming
This Appendix explains the EtherPath's remote
programming interface. This is not used in most
applications. The information is for those writing
programs to access the EtherPath via the
Ethernet.
Introduction
It is rather straightforward to implement a software application to
communicate with serial devices through the EtherPath. Topics
covered in this appendix are:
• EtherPath description and behavior
• Application notes
• Links to sample code
In addition to user-written software applications, there are
“port redirector” software packages that work quite well
with the EtherPath. If you are not a "network
programmer", then port redirector may be the quickest way
to get an application on-line.
For UNIX systems (AIX, Linux, SCO5, FreeBSD, OSF),
Termnet works quite well. It is GNU’d freeware available
from http://www.dcbnet.com or http://www.linuxlots.com
76
Specifications
For Microsoft Windows systems, Serial/IP is an excellent
low-cost program, also available from
http://www.dcbnet.com.
Description and Behavior
Ports used by the EtherPath

The EtherPath uses 3 ports, as follows:
Port Description
Data Port ‘Server Mode’ EtherPath listens at the port and
offers a raw TCP connection. This port number
is configurable. Default is 3000.
From The ‘Client Mode’ EtherPath uses a sending port
Port between 1025 and 4999 to connect to its Remote
Host. The port number starts at 1025, and
increments as needed. Note that EtherPath
version 5.2 and earlier always used port 5000 as
the sending port.
8000 Provides a telnet configuration service for all
modes. Do not use port 8000 in user-written
programs.
For user-written client application, avoid port number 8000. The

"Server" will respond to any configured port number other than that.
77
Server Mode
In Server mode, the EtherPath runs under the TCP/IP network
protocol. It will listen on a configured port number. The server will
wait for connection after initialization.
After a connection is established, the server always keeps checking
for data on both Ethernet and Serial Ports.
If data from the Ethernet network is received, it will first check for a
special control symbol, filter it if found and then send the rest of the
data to the serial port.
If data from the serial port is received, it will read the data from the
serial buffer, move the data into the network buffer and send it by
Ethernet to the application when the buffer is full or on the next tick
of the transmit timer.
Transmit Conditions
The EtherPath will transmit an Ethernet packet when any of these
conditions are met:
• Transmit Timer is up and running in Transmit Timer Mode
• Idle Timer is up and running in Idle Timeout Mode.
• Transmit Buffer full
• LT Character is encountered and Transmit on Line Terminator
Function is ON ( Client Only )
78
Specifications
Locking Avoidance Mechanism

When two EtherPaths are used to emulate a direct serial connection
over the network as described previously, the ‘Server Mode’
EtherPath could be locked if its connecting ‘Client Mode’ EtherPath
disconnects abnormally. If this situation happens, no connection to
the ‘Server Mode’ EtherPath is possible, and it should be reset. To
solve this problem, the following system is used.
When in Telnet Server mode: a telnet NOP command is used
as a heatbeat keep-alive signal. A fixed keep-alive time of 60
seconds is used.
When in Raw Server mode:
1. A "Keep-Alive" message is defined as a 21-byte string:
sErIaLsErVeRkEePaLiVe
9. This string “sErIaLsErVeRkEePaLiVe” is sent out by the
‘Client Mode’ EtherPath if the time since the previous
transmission exceeds the configured keep-alive time. It tells
the ‘Server Mode’ EtherPath that ‘I am still alive and do not
close the connection’. It keeps sending out this string every
keep-alive time seconds if there is no data to send.
10. The ‘Server Mode’ EtherPath will disconnect the link if it does
not receive any packet from the ‘Client Mode’ EtherPath within
a period of three times the keep-alive time.
11. The ‘Server Mode’ EtherPath will then initialize and accept a
new connection. The ‘Client Mode’ EtherPath will attempt to
reconnect as soon as a network path becomes available.
12. User-written programs can avoid this operation by setting the
keep-alive time to zero. If a user-written program uses the
EtherPath keep-alive, the program must handle the keep-alive
packet properly.
79
Application Notes
There are a number of application notes available from the DCB
web site at http://www.dcbnet.com . These cover port redirection,
selecting the proper product (EtherPath vs. EtherPoll), SNMP,
middleware for the EtherPath, a demonstration client-server
software system, and other issues.
A complete copy of the SNMP MIB is available from the same site
along with a free port redirector program (along with source code)
for various UNIX workstations. A trial port redirector program for
Windows is also available. A demonstration program for a
Windows workstation is printed in the next section.
These and more are available in the Education section of that web
site.
80
Specifications
Appendix C
AT Command
Summary
This Appendix explains the EtherPath's AT
command set operation and responses.
AT Commands
The EtherPath recognizes the following AT commands (when
AT Dialing is enabled):
ATD <IP> connect to <IP_address>

ATDT <IP> connect to <IP_address>
ATH[0/1] on/off hook (ATH<cr> == ATH0)
ATO[0/1] return to data mode from command mode, if
connected
ATE[0/1] echo off/on (ATE<cr> == ATE0)
ATS0=[0/1] switch to Client(0) or Server(1) mode, if not
connected
ATV[0/1] terse/verbose response (ATV<cr> == ATV0)
ATZ reset EtherPath (DOES NOT restore factory
defaults)
AT&W save current settings, including ATE and ATV
AT&Z reset EtherPath (Same as ATZ)
+++ escape to command mode when connected
81
AT Command Responses
The serial port responses depend on the ATE setting:
Verbose Terse
OK 0
CONNECT 1
CARRIER 3
ERROR 4
BUSY 7
AT Command Operation
When ATE1 is in effect, there are some addition error
messages such as "Invalid IP address" and "Invalid Entry"
The ATE and ATV settings are saved in non-volatile memory

when the AT&W command is entered, and those settings are
restored when the EtherPath
is reset. The Factory Default setting (main menu, option 6)
for both is ON.
Connections are only allowed when Pin 6 is HIGH or

FORCED HIGH. If not FORCED HIGH, the Pin 6 can be
used to drop a connection. One can also use "+++" then
ATH<cr> to drop a connection.
82
Specifications
Appendix D
RS-422/ RS-485
Interface
This Appendix describes the EtherPath's 4-2843
RS-422/485 interface. This interface option may
configured in the field or pre-configured at the
factory via configuration settings.
Introduction
The 9-pin serial connector on the EtherPath may be for either RS-
232 or RS-422 (4-wire RS-485 point-to-point) operation .
Changing the Setting

The 9-pin serial connector may be used for either RS-232, RS-422
(4-wire RS-485 point-to-point), or 2-wire RS-485 operation by
changing software configuration settings on the Configure Port
screens..
83
RS-422 / 4-Wire RS-485 Interface Pinout

1 No Connection N/A
2 Transmit Data (TX+) Out
3 Receive Data (Rx+) In
4 No Connection N/A
5 Signal Ground (GND) N/A
6 No Connection N/A
7 Receive Data (Rx-) In
8 Transmit Data (Tx-) Out
9 No Connection N/A
NOTE: Older versions of this product used a different pin out

for RS-422 and RS-485. For plug-in compatibility, order
adapter part number 9802073 .
84
Specifications
2-Wire RS-485 Interface Pinout

1 No Connection N/A
2 No Connection N/A
3 Data + In/Out
4 No Connection N/A
5 Signal Ground (GND) N/A
6 No Connection N/A
7 Data - In/Out
8 No Connection N/A
9 No Connection N/A
NOTE: Older versions of this product used a different pin out

for RS-422 and RS-485. For plug-in compatibility, order
adapter part number 9802073 .
RS-485 2-wire Fan-out

Since this unit is most often used as an RS-485 2-wire end-point, it
will support 32 devices on the RS-485 line. Use good engineer
practice for RS-485 lines. Where applicable, include termination
for long lines.
85

etherpath

Uploaded by

Copyright:

Available Formats

etherpath

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

etherpath

Uploaded by

Copyright:

Available Formats

EtherPath

Revised April 12, 2007

This is a class B product. In a domestic environment this product

Copyright  1998…2007. All rights reserved.

C ongratulations on the purchase of your new EtherPath. The

Figure 1: Modes of Operation

Point-to-Multiple-Point (EtherModem) Mode

Reverse Telnet (Telnet Client) Mode

The EtherPath has been tested to work with:

1. Connect the Network Cable

3. Connect the Serial Port Device

If you can't connect

3. Refer to the following section for details on using the

EtherPath Main Menu

Each of these menu options is explained in the following pages.

LOCAL UNIT CONFIGURATION:

Enter Command =>

Enter Command =>

SET PORT CONFIGURATION:

EXAMPLE: To set the baud rate to 19200

Enter Command =>

SET ADVANCED CONFIGURATION:

EXAMPLE: To set the Flow OFF level to 75%

Enter Command =>

CURRENT ETHERPATH CONFIGURATION:

Network Packets Received

Main Menu Option 7.

Main Menu Option 8.

SET SECURITY CONFIGURATION:

Set Security Configuration Screen

Disable Telnet Configuration

Disable SNMP Agent

Set User ID and Password

Clear User ID and Password

The EtherPath uses the industry standard IP protocol. Since this is a

Main Menu Option 9.

SET SNMP CONFIGURATION:

Enter Command =>

Main Menu Option 0.

1. Install the EtherPath in your LAN as described in Chapter 2.

The first screen is similar to Figure 2.

Figure 2: Sign on Screen

Port Configuration Screen

Figure 3: Port Configuration Screen

Port Activity Screen

Figure 4:Port Activity Screen

This screen displays details about the data currently being

Data - Serial Port

Advanced Configuration Screen

Figure 5: Advanced Configuration Screen

LAN Configuration Screen

Figure 6: LAN Configuration Screen

Remote Device IP Address

Remote (Listen) IP Port Number

SNMP Configuration Screen

Figure 7: SNMP Configuration Screen

Configuration Summary Screen

Figure 8:Configuration Summary Screen

Client/Server Point-to-Point (Nailed-Up)

Client (Reverse Telnet) Mode