For the electronic measurement of currents: DC, AC, pulsed..., with
galvanic separation between the primary circuit and the secondary DUAL PHASE circuit.
All data are given with RL = 10 kΩ
Electrical data Features IP N Primary nominal RMS current ±20 A IP M Primary current, measuring range ±60 A ● Hall effect measuring principle SN Nominal sensitivity 0.625 V/ IP N ● Multirange current transducer Uout Output voltage (Analog) @ IP UO E ±(0.625·IP/ IP N) V through PCB pattern lay-out Uref Reference voltage 1) Output voltage 2.5 ±0.025 V ● Galvanic separation between Output impedance typ. 200 Ω primary and secondary circuit Load impedance 200 kΩ ● Insulation test voltage 3500 V RL Load resistance 2 kΩ ● Extremely low profile < 11 mm Rout Output internal resistance <5 Ω ● Fixed offset & sensitivity CL Load capacitance (±20 %) 4.7 nF ● Low power consumption UC Supply voltage (±5 %) 2) 5 V ● Single power supply +5 V IC Current consumption @ UC = 5 V 19 mA ● Insulating plastic case recognized according to UL 94-V0. Accuracy - Dynamic performance data Advantages ε Error 3) @ IP N, TA = 25 °C ±1 % εL Linearity error 0 ... IP N ±0.5 % ● Small size and space saving 0 ... 3 × IP N ±1 % ● Only one design for wide current TCUO E Temperature of coefficient of UO E (+25 ... 105 °C) ±0.4 mV/K ratings range (−40 ... +25 °C) ±0.525 mV/K ● High immunity to external TCUref Temperature of coefficient of Uref (+25 ... 105 °C) ±0.01 %/K interference (−40 ... +25 °C) ±0.015 %/K ● Uref IN/OUT. TCUO E / UrefTemperature coefficient of UO E /Uref ±0.15 mV/K Application TCS Temperature of coefficient of S ±0.05% of reading/K UO E Electrical offset voltage @ IP = 0, TA = 25 °C Uref ±0.0125 V ● AC variable speed drives and UO M Magnetic offset voltage @ IP = 0 servo motor drives after an overload of 3 × IPN ±0.7 % ● Static converters for DC motor tD 10 Delay time to 10 % of the final output value for IP N step < 3 µs drives tD 90 Delay time to 90 % of the final output value for IP N step 4) < 5 µs ● Battery supplied applications Uno Output voltage noise (DC ... 10 kHz) < 20 mVpp ● Uninterruptible Power Supplies (DC ... 1 MHz) < 40 mVpp (UPS) BW Frequency bandwidth (−3 dB) 5) DC ... 50 kHz ● Switched Mode Power Supplies Notes: 1) It is possible to overdrive Uref with an external reference voltage between (SMPS) 1.5 - 2.8 V providing its ability to sink or source approx. 5 mA ● Power supplies for welding 2) Maximum supply voltage (not operating) < 6.5 V applications. 3) Excluding offset and magnetic offset voltage Application domain 4) For a di/dt = 50 A/µs 5) Small signal only to avoid excessive heatings of the magnetic core. ● Industrial.
N°74.90.17.000.0 Page 1/3
9October2023/Version 23 LEM reserves the right to carry out modifications on its transducers, LEM International SA in order to improve them. Route du Nant-d’Avril, 152 1217 Meyrin www.lem.com Current Transducer HXS 20-NP General data TA Ambient operating temperature 1) −40 ... +105 °C TA st Ambient storage temperature −40 ... +105 °C m Mass 10 g Standards EN 50178:1997 Note: 1) UL recognized with surrounding temperature until +85 °C.
Insulation coordination Ud RMS voltage for AC insulation test, 50 Hz, 1 min 3.5 kV Min dCp Creepage distance 7.48 mm dCI Clearance 6.6 mm CTI Comparative tracking index (group I) > 600
Applications examples According to EN 50178 and IEC 61010-1 standards and following conditions:
● Over voltage category OV 3
● Pollution degree PD2 ● Non-uniform field
According to UL 508 standards and following conditions: Maximum voltage 600 V
● Over voltage category OV 3
● Pollution degree PD2
EN 50178 IEC 61010-1
dCp , dCI Rated insulation voltage Nominal voltage Basic insulation 600 V 600 V Reinforced insulation 300 V 150 V
Safety This transducer must be used in limited-energy secondary circuits according to IEC 61010-1.
This transducer must be used in electric/electronic equipment with respect to
applicable standards and safety requirements in accordance with the manufacturer’s operating instructions.
Caution, risk of electrical shock
When operating the transducer, certain parts of the module can carry hazardous voltage (eg. primary busbar, power supply). Ignoring this warning can lead to injury and/or cause serious damage. This transducer is a build-in device, whose conducting parts must be inaccessible after installation. A protective housing or additional shield could be used. Main supply must be able to be disconnected. Page 2/3
9October2023/Version 23 LEM reserves the right to carry out modifications on its transducers, LEM International SA in order to improve them. Route du Nant-d’Avril, 152 1217 Meyrin www.lem.com Dimensions HXS 20-NP (in mm)
dCl dCP
Connection
+ UC
Uout Uref
Primary RMS current Primary
Primary Primary Recommended insertion connections nominal maximum resistance PCB connections inductance IP N [ A ] IP [ A ] RP [ mΩ ] LP [ µH ] IN 1 3 5 7 1 20 60 0.05 0.025 2 4 6 8 OUT IN 1 3 5 7 2 10 30 0.2 0.1 2 4 6 8 OUT IN 1 3 5 7 4 5 15 1 0.4 2 4 6 8 OUT
Mechanical characteristics Remarks
● General tolerance ±0.2 mm ● Uout is positive when IP flows from terminals 1,3 ,5, 7 (IN) to ● Transducer fastening & terminals 2 , 4, 6, 8 (OUT). connection of primary jumper 8 pins 1.2 × 1.2 mm ● Temperature of the primary conductor should not exceed (corner R 0.4 mm) 120 °C. ● Transducer fastening & ● IInstallation of the transducer must be done, unless connection of secondary pin 4 pins 0.5 × 0.25 mm otherwise specified on the datasheet, according to LEM Transducer Generic Mounting Rules. Please refer to LEM Recommended PCB hole document N°ANE120504 available on our Web site: ● Primary PCB hole ⌀ 1.5 mm https://www.lem.com/en/file/3137/download ● Secondary PCB hole ⌀ 0.7 mm Page 3/3
9October2023/Version 23 LEM reserves the right to carry out modifications on its transducers, LEM International SA in order to improve them. Route du Nant-d’Avril, 152 1217 Meyrin www.lem.com
