Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
0% found this document useful (0 votes)
10 views

mod-cfc-3pro

Uploaded by

Kalimuthu S
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
0% found this document useful (0 votes)
10 views

mod-cfc-3pro

Uploaded by

Kalimuthu S
Copyright
© © All Rights Reserved
Available Formats
Download as PDF, TXT or read online on Scribd
You are on page 1/ 3

3 CH Ceiling Fan Controller-Modbus RTU Technical details

MOD-CFC-3 Pro

▪ 3 Channel Ceiling Fan Controller


▪ Control up to 5 speeds for each channel
▪ Manual output operation with push button
▪ Total data saving on bus failure
▪ DIN rail mount assembly
▪ Dimension: 142.3 (L) X 90.5 (H) X 62 (D) mm [8 DIN Units]
▪ DIP switch for Modbus RTU slave configuration
▪ No configuration software needed
▪ CE Mark

▪ Manual Push Button:


▪ 1. FAN: Select Fan Channel to be operate
▪ 2. STEP: Change speed of fan from 0 to 5

General Product Specifications


Type of Device Electric operation control device
Voltage, C u r r e n t 24VDC / 35mA
Main (typical)
Supply Voltage Range 18-30 VDC
Connection type Terminal Block (Screw)
External Supply 230VAC,50Hz, + 10 % -20%
Communication Interface & Protocol RS485 & Modbus RTU
No. of Channels 3
Speed control for each channel Step 1 to 5 and OFF
Maximum recommended load per 90W
output
IP Level IP20
Protection Fuse Protection for AC supply.
Isolation No Isolation

Messung Systems Pvt. Ltd.


501 Lunkad Sky Vista, Viman Nagar, Pune 411 014, India.
T:+91 20 6649 2800 | e: info@messung.com | w: www.messung.com
Operating Temperature 0 - 70 °C
Storage Temperature -25 to 75 °C
Ambient Humidity 5 to 95% RH (No Condensation)
Dimension 142.3 (L) X 90.5 (H) X 62 (D) mm [8 DIN Units]
2 Push Buttons: 1 – Select Fan No. 2 –
Manual Test Facility
Select Fan Speed
Indoor, to be mounted inside distribution boxes or electrical panels
Usage
with DIN rail
LED (RED) for DC power ON, Flickering Yellow LED to indicate
LED Indication
communication, GREEN LED’s (3 no’s) indicating fan channel selection.

Output Specifications and Connections


Maximum Load per Channel 90W
(Recommended)
Mains Input Voltage 230VAC (50 Hz) +10% -20%
Connection Type Terminal Block (Screw)
Recommended Cable Section 0.5 mm2 to 4 mm2(26-10AWG)
Cable Type Stranded or Solid Wire
Output Relay rating 16A/250VAC
Rated current by output 16A*277 VAC (4,432 VA)

Modbus Communication Specifications


Protocol Modbus RTU
Baud Rate 9600,19200,38400
Slave Address 1-15
Data Bit 8-bit
Stop Bit 1-bit
Parity None
Response Time <100ms
Termination Resistance 120 ohms
Control Registers Holding Register 1 to 3(value 0-5)
(status Holding Register 6-8)
Distance Up to 1200m

CANopen Slave Configuration DIP Switch Steps:


1. Switch S1-8 for address, baud rate, Termination.
Adjust the DIP switch according to requirements. Refer below image.

SWITCH 1-8

NODE ID Configuration

Node ID Switch1 Switch2 Switch3 Switch4

1 ON OFF OFF OFF

2 OFF ON OFF OFF

3 ON ON OFF OFF

… … … … …

15 ON ON ON ON

Baud Rate Configuration

Baud Rate Switch5 Switch6

Messung Systems Pvt. Ltd.


501 Lunkad Sky Vista, Viman Nagar, Pune 411 014, India.
T:+91 20 6649 2800 | e: info@messung.com | w: www.messung.com
9600 OFF OFF

19200 ON OFF

38400 OFF ON

Termination

Switch7

Termination OFF OFF

Termination ON ON

Not used Switch8

Wiring Diagram:

SAFETY INSTRUCTIONS
▪ Installation should only be performed by qualified professionals according to the laws and
regulations.
▪ Do not connect the mains voltage nor any other external voltage to any point of the CAN connector;
it would represent a risk for the entire system. The facility must have enough insulation between
the mains (or auxiliary) voltage and the Modbus or the wires of other accessories, in case of being
installed.
▪ Keep the device away from water and do not cover it with clothes, paper or any other material while
in use.
▪ Not suitable for BLDC fan, Pedestial Fan, Exhaust Fan, Table Fan.

Messung Systems Pvt. Ltd.


501 Lunkad Sky Vista, Viman Nagar, Pune 411 014, India.
T:+91 20 6649 2800 | e: info@messung.com | w: www.messung.com

You might also like