NOT RECOMMENDED FOR NEW DESIGN - USE AP7361C

AP7361
1A LOW DROPOUT ADJUSTABLE AND FIXED-MODE REGULATOR WITH ENABLE

Description Pin Assignments

The AP7361 is a 1A, adjustable and fixed output voltage, ultra-low
(Top View)
dropout linear regulator with enable. The device includes pass
element, error amplifier, band-gap reference, current limit and thermal
OUT 1 8 IN
shutdown circuitry. The device is turned on when the EN pin is set to
NC 2 7 NC
logic high level. GND
ADJ/NC 3 6 NC
The characteristics of the low dropout voltage and low quiescent GND 4 5 EN
current make it suitable for low to medium power applications, for
U-DFN3030-8
example, laptop computers, audio and video applications, and battery
powered devices. The typical quiescent current is approximately ( Top View ) ( Top View )
70µA. Built-in current-limit and thermal-shutdown functions prevent
IC from damage in fault conditions. 3 3

The AP7361 is available in U-DFN3030-8, SOT89-5, SOT223, TO252 2 2 2

and SO-8EP package. 1 1

Features SOT223/SOT223R TO252/TO252R

 Wide input voltage range: 2.2V - 6V

(Top View)
 150mV Very Low Dropout at 300mA Load (Top View)
 500mV Very Low Dropout at 1A Load OUT 1 8 IN
EN 1 5 OUT
 Low Quiescent Current (IQ): 70µA Typical EN 2 7 NC
 Adjustable Output Voltage Range: 1V to 5.0V GND 2 GND 3 6 NC
NC
 Fixed Output Options: 1V to 3.3V
GND 4 5 NC
 Very-Fast Transient Response ADJ/NC 3 4 IN
 High PSRR SOT89-5 SO-8EP
 Accurate Voltage Regulation
 Current Limiting and Short Circuit Protection
 Thermal Shutdown Protection Applications
 Stable with Ceramic Output Capacitor  2.2µF  Servers and Laptops
 Ambient Temperature Range -40°C to +85°C  FPGA and DSP Core or I/O Power
 U-DFN3030-8, SOT89-5, SOT223/SOT223R, TO252/TO252R  TV, and Home Electrical Appliances
and SO-8EP  Battery-Powered Devices
 Available in “Green” Molding Compound (No Br, Sb)
 Totally Lead-Free & Fully RoHS Compliant (Notes 1 & 2)
 Halogen and Antimony Free. “Green” Device (Note 3)

Notes: 1. No purposely added lead. Fully EU Directive 2002/95/EC (RoHS) & 2011/65/EU (RoHS 2) compliant.
2. See http://www.diodes.com/quality/lead_free.html for more information about Diodes Incorporated’s definitions of Halogen- and Antimony-free, "Green"
and Lead-free.
3. Halogen- and Antimony-free "Green” products are defined as those which contain <900ppm bromine, <900ppm chlorine (<1500ppm total Br + Cl) and
<1000ppm antimony compounds.

AP7361 1 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Typical Applications Circuit

VIN VOUT VIN VOUT

IN OUT IN OUT

AP7361 AP7361 R1
1uF 4.7uF 1uF 4.7uF
Enable Enable
EN EN ADJ

GND GND
R2

Fixed Version Adjustable Output

U-DFN3030-8, SOT89-5 and SO-8EP U-DFN3030-8 and SOT89-5

VIN VOUT
IN OUT

AP7361
1uF 4.7uF

GND

Fixed Version
TO252, SOT223

Pin Descriptions
Pin Pin Number
Function
Name U-DFN3030-8 SOT89-5 TO252 TO252R SOT223 SOT223R SO-8EP
The input of the regulator. Bypass to ground through at
IN 8 4 1 3 1 3 8
least 1µF ceramic capacitor.
The output of the regulator. Bypass to ground through
OUT 1 5 3 2 3 2 1 at least 2.2µF ceramic capacitor. For improved ac load
response a larger capacitor is recommended.
GND 4 2 2 1 2 1 4 Ground
Adjustable voltage version only – a resistor divider from
ADJ 3 3 NA NA NA NA NA this pin to the OUT pin and ground sets the output
voltage.
EN 5 1 NA NA NA NA 2 Enable input, active high
NC 2, 6, 7 NA NA NA NA NA 3, 5, 6, 7 No connection

AP7361 2 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Functional Block Diagram

IN OUT IN OUT

Current Limit Current Limit

Gate Gate
EN Driver
and Thermal EN Driver
and Thermal
Shutdown R Shutdown

ADJ

0.8V 0.8V

GND GND

Fixed Version U-DFN3030-8, SOT89-5 and SO-8EP Adjustable Version U-DFN3030-8 and SOT89-5

IN OUT

Current Limit
Gate
and Thermal
Driver
Shutdown R

0.8V

GND

Fixed Version
TO252, SOT223

AP7361 3 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Absolute Maximum Ratings (@TA = +25°C, unless otherwise specified.)

Symbol Parameter Ratings Unit
ESD HBM Human Body Model ESD Protection >2 KV
ESD MM Machine Model ESD Protection (Note 5) > 200 V
VIN Input Voltage 6.5 V
OUT, ADJ, EN Voltage VIN +0.3 V
TJ Operating Junction Temperature Range -40 to +150 °C
TST Storage Temperature Range -65 to +150 °C
Internally limited by maximum junction
PD Power Dissipation (Note 4)
temperature of +150°C
U-DFN3030-8 1,700
TO252 1,250
PD Power Dissipation (Note 4) SOT223 1,100 mW
SOT89-5 800
SO-8EP 1,190
Notes: 4. Ratings apply to ambient temperature at +25°C.
5. ESD MM rating at 150V for EN pin.

Stresses greater than the 'Absolute Maximum Ratings' specified above, may cause permanent damage to the device. These are stress ratings only;
functional operation of the device at these or any other conditions exceeding those indicated in this specification is not implied. Device reliability may be
affected by exposure to absolute maximum rating conditions for extended periods of time.

Recommended Operating Conditions (@TA = +25°C, unless otherwise specified.)

Symbol Parameter Min Max Unit
VIN Input Voltage 2.2 6.0 V
IOUT Output Current (Note 6) 0 1.0 A
TA Operating Ambient Temperature -40 +85 C
Note: 6. The device maintains a stable, regulated output voltage without a load current. When the output current is large, attention should be given to the
limitation of the package power dissipation.

AP7361 4 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Electrical Characteristics (@TA = +25°C, VIN = VOUT +1V, CIN = 1μF, COUT = 4.7μF, VEN = VIN unless otherwise specified.)

Symbol Parameter Test Conditions Min Typ Max Unit

VREF FB Reference Voltage IOUT = 10mA, TA = +25°C 0.8 V
IADJ ADJ Pin Leakage 0.1 0.5 µA
IQ Input Quiescent Current Enabled, IOUT = 0A 70 90 µA
ISHDN Input Shutdown Current VEN = 0V, IOUT = 0A -1 0.05 1 µA
IOUT = 100mA, TA = +25°C -1 1
VOUT Output Voltage Accuracy IOUT = 100mA, -40°C ≤ TA ≤ +85°C -2 2 %
Over VIN, IOUT, and TA -3 ±0.5 3
ΔVOUT VIN = VOUT +1V to TA = +25°C 0.01 0.1
Line Regulation %/V
ΔVIN VOUT 6V, IOUT = 100mA -40°C ≤TA ≤ +85°C 0.2
IOUT from 1mA to 300mA -1.0 0.5 1.0 %
VOUT / VOUT Load Regulation
IOUT from 1mA to 1A -1.0 0.5 1.0 %
IOUT = 300mA 150 200
VDROPOUT Dropout Voltage (Note 7) IOUT = 500mA 250 350 mV
IOUT = 1A 500 700
VIL EN Input Logic Low Voltage 0 0.3 V
VIH EN Input Logic High Voltage 1.0 VIN V
IEN EN Input Leakage VIN = 6V, VEN = 0V or 6V -0.1 0.01 0.1 µA
ILIMIT Current Limit VIN = VOUT +1V 1.1 1.5 A
ISHORT Short-Circuit Current VIN = VOUT +1V, Output Voltage < 15% VOUT 200 mA
Power Supply Rejection Ratio f = 1KHz, IOUT = 100mA 60 65
PSRR dB
(Note 8) f = 10KHz, IOUT = 100mA 45
tST Start-Up Time VOUT = 3V, COUT = 1µF, RL = 30Ω 200 µs
ΔVOUT
Output Voltage Temperature Coefficient IOUT = 100mA, -40°C ≤ TA ≤ +85°C ±130 ppm/°C
ΔTA  VOUT
TSHDN Thermal Shutdown Threshold 150 °C
THYS Thermal Shutdown Hysteresis 20 °C
U-DFN3030-8 (Note 9) 70
TO252 (Note 9) 95
θJA Thermal Resistance Junction-to-Ambient SOT223 (Note 9) 110 °C/W
SOT89-5 (Note 9) 150
SO-8EP (Note 9) 100
Notes: 7. Dropout voltage is the voltage difference between the input and the output at which the output voltage drops 2% below its
nominal value. This parameter only applies to output voltages above 1.5V since minimum V IN = 2.2V.
8. For VIN  2.5V and VIN = VOUT +1V. For VIN < 2.5V, the PSRR performance may be reduced.
9. Test condition: DFN3030E-8, SO-8EP device mounted on 2"x2", FR-4 substrate PCB, with minimum recommended pad on top layer and thermal vias to
bottom layer ground plane. TO252 device mounted on 2"x2" FR-4 substrate PC board, 2oz copper, with minimum recommended pad layout.
SOT223 the device is mounted on FR-4 substrate PC board, with minimum recommended pad layout. SOT89-5L device mounted on 1"x1" FR-4
substrate PC board, with minimum recommended pad layout.

AP7361 5 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Typical Performance Characteristics

Start-up Time Start-up Time

VEN = 0 to 2V (1V/div) VEN = 0 to 2V (1V/div)

VIN = 4.0V VIN = 4.0V

CIN = COUT=1μF CIN = COUT = 1μF

VOUT = 3.0V (1V/div) VOUT = 3.0V (1V/div)

with 100mA load with 500mA load

Time (100μs/div) Time (100μs/div)

Line Transient Response Line Transient Response

VIN = 4.3V to 5.3V (1V/div) VIN = 5.5V to 6V (1V/div)

Tr = Tf = 5μs Tr = Tf = 5μs

IOUT = 100mA IOUT = 100mA

COUT = 4.7μF COUT = 4.7μF

VOUT = 3.3V (20mV/div) VOUT = 5.0V (20mV/div)

Time (40μs/div) Time (40μs/div)

AP7361 6 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Typical Performance Characteristics (cont.)

Load Transient Response Load Transient Response

VIN = VEN = 2.2V VIN = VEN = 2.2V

CIN = 1μF,COUT = 4.7μF CIN = 1μF,COUT = 4.7μF

VOUT = 1.2V (20mV/div) VOUT = 1.2V (20mV/div)

IOUT = 50mA to 100mA (50mA/div)

IOUT = 100mA to 500mA (200mA/div)

Time (200μs/div) Time (200μs/div)

Load Transient Response Load Transient Response

VIN = VEN = 4.3V VIN = VEN = 4.3V

CIN = 1μF,COUT = 4.7μF CIN = 1μF,COUT = 4.7μF

VOUT = 3.3V (20mV/div) VOUT = 3.3V (20mV/div)

IOUT = 50mA to 100mA (50mA/div)

IOUT = 100mA to 500mA (200mA/div)

Time (200μs/div) Time (200μs/div)

AP7361 7 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Typical Performance Characteristics (cont.)

Load Transient Response Load Transient Response

VIN = VEN = 6.0V VIN = VEN = 6.0V

CIN = 1μF,COUT = 4.7μF CIN = 1μF,COUT = 4.7μF

VOUT = 5.0V (20mV/div) VOUT = 5.0V (20mV/div)

IOUT = 50mA to 100mA (50mA/div)

IOUT = 100mA to 500mA (200mA/div)

Time (200μs/div) Time (200μs/div)

PSRR vs Frequency PSRR vs Frequency

100 100
90 IOUT = 30mA 90 IOUT = 30mA
80 80
70 70
PSRR(dB)
PSRR(dB)

60 60
50 IOUT = 100mA 50 IOUT = 100mA

40 40
30 VIN = 2.5V +0.5VppAC 30 VIN = 2.8V +0.5VppAC
VOUT = 1.2V VOUT = 1.8V
20 COUT = 4.7μF 20 COUT = 4.7μF
TA = +25°C TA = +25°C
10 10
0 0
0.01
10 100
0.1 1k
1 10k
10 100k
100 1000
1M 10
0.01 100
0.1 1k
1 10k
10 100k
100 1M
1000
Frequency(Hz) Frequency(Hz)

AP7361 8 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Typical Performance Characteristics (cont.)

PSRR vs Frequency PSRR vs Frequency

100 100
IOUT = 30mA
90 90 IOUT = 30mA

80 80
70 70

PSRR(dB)
PSRR(dB)

60 60
50 IOUT = 100mA 50
IOUT = 100mA
40 40
30 30 VIN = 4.3V +0.5VppAC
VIN = 3.5V +0.5VppAC
VOUT = 3.3V
20 VOUT = 2.5V 20
COUT = 4.7μF COUT = 4.7μF
TA = +25°C
10 TA = +25°C 10

0 0
10
0.01 100
0.1 1k
1 10k
10 100k
100 1M
1000 10
0.01 100
0.1 1k
1 10k
10 100k
100 1M
1000
Frequency(Hz) Frequency(Hz)

FB Reference Voltage vs Temperature Dropout Voltage vs Output Current

0.82 600
VIN = 4.3V VOUT = 3.3V
500
FB Reference Voltage(V)

Dropout Voltage(mV)

0.81 IOUT = 100mA

25°C
400
85°C
0.80 300

200 -40°C
0.79
100

0.78 0
-50 -25 0 25 50 75 100 125 0 200 400 600 800 1000
Temperature(℃) Output Current(mA)

AP7361 9 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Typical Performance Characteristics (cont.)

Current limit vs Input Voltage Current limit vs Temperature

2.5 2.5

2.0 2.0

Current limit(A)
Current limit(A)

1.5 1.5

1.0 1.0
VIN = 2.2V
VOUT = 1.2V
0.5 0.5 VOUT = 1.2V

0.0 0.0
2 3 4 5 6 -50 -25 0 25 50 75 100 125
Input Voltage(V) Temperature(℃)

Current limit vs Temperature Short-circuit current vs Temperature

2.5 300

250
Short-circuit current (mA)

2.0
Current limit(A)

200
1.5
150
1.0
VIN = 4.3V 100
VIN = 4.3V
0.5 VOUT = 3.3V
50

0.0 0
-50 -25 0 25 50 75 100 125 -50 -25 0 25 50 75 100 125
Temperature(℃) Temperature(℃)

AP7361 10 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Typical Performance Characteristics (cont.)

Load Regulation Line Regulation

0.9 0.2
VIN = VEN = 4.3V
VOUT = 3.3V
0.6 VOUT = 3.3V

Output Variation(%/V)
85°C 0.1 IOUT = 100mA
Output Variation(%)

25°C 85°C
0.3

0.0 0.0

-0.3
-40°C -0.1
-0.6 25°C -40°C

-0.9 -0.2
0 200 400 600 800 1000 4 4.5 5 5.5 6

Output Current(mA) Input Voltage(V)

Input Quiescent Current vs Temperature Input Quiescent Current vs Input Voltage

80 80
Input Quiescent Current(μA)

Input Quiescent Current(μA)

60 60

40 40

20 VIN = VEN = 4.3V 20 TA = +25°C

IOUT = 0mA IOUT = 0mA

0 0
-50 -25 0 25 50 75 100 125 4 4.5 5 5.5 6
Temperature(℃) Input Voltage(V)

AP7361 11 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Application Information
Input Capacitor
A 1μF ceramic capacitor is recommended between IN and GND pins to decouple input power supply glitch and noise. The amount of the
capacitance may be increased without limit. This input capacitor must be located as close as possible to the device to assure input stability and
reduce noise. For PCB layout, a wide copper trace is required for both IN and GND pins. A lower ESR capacitor type allows the use of less
capacitance, while a higher ESR type requires more capacitance.

Output Capacitor
The output capacitor is required to stabilize and improve the transient response of the LDO. The AP7361 is stable with very small ceramic output
capacitors. Using a ceramic capacitor value that is at least 2.2μF with 10mΩ ≦ ESR ≦ 300mΩ on the output ensures stability. Higher capacitance
values help to improve line and load transient response. The output capacitance may be increased to keep low undershoot and overshoot. Output
capacitor must be placed as close as possible to OUT and GND pins.

Adjustable Operation
Adjustable operation is not available in the SOT223 TO252 and SO-8EP package. The AP7361 provides output voltage from 0.8V to 5.0V through

external resistor divider as shown below.

VIN VOUT
IN OUT

AP7361 R1
1uF 4.7uF
Enable
EN ADJ

GND
R2

Adjustable Output

The output voltage is calculated by:

 R 
VOUT  VREF 1  1 
 R2 

Where VREF = 0.8V (the internal reference voltage)

Rearranging the equation will give the following that is used for adjusting the output to a particular voltage:
V 
R1  R2  OUT  1
V
 REF 

To maintain the stability of the internal reference voltage, R2 need to be kept smaller than 80kΩ.

AP7361 12 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Application Information
No Load Stability
Other than external resistor divider, no minimum load is required to keep the device stable. The device will remain stable and regulated in no load
condition.

ON/OFF Input Operation

The ON/OFF feature is not available in the SOT223 and TO252 package.

The AP7361 is turned on by setting the EN pin high, and is turned off by pulling it low. If this feature is not used, the EN pin should be tied to IN pin
to keep the regulator output on at all time. To ensure proper operation, the signal source used to drive the EN pin must be able to swing above and
below the specified turn-on/off voltage thresholds listed in the Electrical Characteristics section under VIL and VIH.

Current Limit Protection

When output current at OUT pin is higher than current limit threshold, the current limit protection will be triggered and clamp the output current to
prevent overcurrent and to protect the regulator from damage due to overheating.

Short-Circuit Protection
When OUT pin is short-circuit to GND, short circuit protection will be triggered and clamp the output current to approximately 200mA. Full current is
restored when the output voltage exceeds 15% of Vout. This feature protects the regulator from overcurrent and damage due to overheating.

Thermal Shutdown Protection

Thermal protection disables the output when the junction temperature rises to approximately +150°C, allowing the device to cool down. When the
junction temperature reduces to approximately +130°C the output circuitry is enabled again. Depending on power dissipation, thermal resistance,
and ambient temperature, the thermal protection circuit may cycle on and off. This cycling limits the heat dissipation of the regulator, protecting it
from damage due to overheating.

Ultra Fast Start-up

After enabled, the AP7361 is able to provide full power in as little as tens of microseconds, typically 200µs, without sacrificing low ground current.
This feature will help load circuitry move in and out of standby mode in real time, eventually extend battery life for mobile phones and other portable
devices.

Low Quiescent Current

The AP7361, consuming only around 70µA for all input range, provides great power saving in portable and low power applications.

Power Dissipation
The device power dissipation and proper sizing of the thermal plane that is connected to the thermal pad is critical to avoid thermal shutdown and
ensure reliable operation. Power dissipation of the device depends on input voltage and load conditions and can be calculated by:

PD = (VIN - VOUT) X IOUT

The maximum power dissipation, handled by the device, depends on the maximum junction to ambient thermal resistance, maximum ambient
temperature, and maximum device junction temperature, which can be calculated by the equation in the following:
( 150C - TA )
PD (max@TA ) 
R JA

AP7361 13 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Ordering Information

AP7361 - XX XXX - X

Output Package Packing

Blank : ADJ FGE : U-DFN3030-8 7 : Tape & Reel
10 : 1.0V
12 : 1.2V
15 : 1.5V
18 : 1.8V
25 : 2.5V
28 : 2.8V
33 : 3.3V
AP7361 - XX X - XX

Output Package Packing

Blank : adj * DR : TO252R 13 : Tape & Reel
10 : 1.0V ER : SOT223R
12 : 1.2V
15 : 1.5V
18 : 1.8V
25 : 2.5V
28 : 2.8V
33 : 3.3V
AP7361 - XX X - XX

Output Package Packing

Blank : ADJ * Y : SOT89-5 13 : Tape & Reel
10 : 1.0V D : TO252
12 : 1.2V E : SOT223
15 : 1.5V SP : SO-8EP
18 : 1.8V
25 : 2.5V * adjustable only in SOT89-5
28 : 2.8V
33 : 3.3V

7”/13” Tape and Reel

Part Number Package Code Packaging
Quantity Part Number Suffix
AP7361-XXFGE-7 FGE U-DFN3030-8 3,000/Tape & Reel -7
AP7361-XXY-13 Y SOT89-5 2,500/Tape & Reel -13
AP7361-XXD-13 D TO252 2,500/Tape & Reel -13
AP7361-XXDR-13 DR TO252R 2,500/Tape & Real -13
AP7361-XXE-13 E SOT223 2,500/Tape & Reel -13
AP7361-XXER-13 ER SOT223R 2,500/Tape & Reel -13
AP7361-XXSP-13 SP SO-8EP 2,500/Tape & Reel -13

AP7361 14 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Marking Information

(1) U-DFN3030-8

( Top View )
XX : Identification Code
XX Y : Year : 0~9
W : Week : A~Z : 1~26 week;
YW X a~z : 27~52 week; z represents
52 and 53 week
X : A~Z : Internal code

Device Package Identification Code

AP7361ADJ U-DFN3030-8 PA
AP7361-10 U-DFN3030-8 PB
AP7361-12 U-DFN3030-8 PC
AP7361-15 U-DFN3030-8 PD
AP7361-18 U-DFN3030-8 PE
AP7361-25 U-DFN3030-8 PF
AP7361-28 U-DFN3030-8 PG
AP7361-33 U-DFN3030-8 PH

(2) SOT89-5

(Top View)
5 4
7

XX : Identification code
Y : Year : 0~9
XX Y W X W : Week : A~Z : 1~26 week;
a~z : 27~52 week;
z represents 52 and 53 week
X : A~Z : Internal code
1 2 3

Device Package Identification Code

AP7361ADJ SOT89-5 PA
AP7361-10 SOT89-5 PB
AP7361-12 SOT89-5 PC
AP7361-15 SOT89-5 PD
AP7361-18 SOT89-5 PE
AP7361-25 SOT89-5 PF
AP7361-28 SOT89-5 PG
AP7361-33 SOT89-5 PH

AP7361 15 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Marking Information (cont.)

(3) TO252

Pin 1: VIN, Pin 2: GND, Pin 3: VOUT

( Top View )

Logo
A~Z : Internal code
Part Number 61-VV YY : Year : 01~09
61-VV : 10 for 1.0V YY WW X X WW : Week : 01~52, 52 represents
12 for 1.2V 52 and 53 week
X : Internal Code
15 for 1.5V
18 for 1.8V
25 for 2.5V
28 for 2.8V
33 for 3.3V

(4) SOT223

Pin 1: VIN, Pin 2: GND, Pin 3: VOUT

( Top View )

Y : Year : 0~9
Logo YWX W : Week : A~Z : 1~26 week;
a~z : 27~52 week;
6 1-VV z repersents 52 and 53 week
Part Number X : Internal code
61-VV : 10 for 1.0V
12 for 1.2V
15 for 1.5V
18 for 1.8V
25 for 2.5V
28 for 2.8V
33 for 3.3V

(5) SOT223R

Pin 1: GND, Pin 2: VOUT, Pin 3: VIN

( Top View )

Y : Year : 0~9
Logo YWX W : Week : A~Z : 1~26 week;
a~z : 27~52 week;
6 1 R-VV z repersents 52 and 53 week
Part Number X : Internal code
61R-VV : 10 for 1.0V
12 for 1.2V
15 for 1.5V
18 for 1.8V
25 for 2.5V
28 for 2.8V
33 for 3.3V

AP7361 16 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Marking Information (cont.)

(6) TO252-R

Pin 1: GND, Pin 2: VOUT, Pin 3: VIN

( Top View )

Logo
A~Z : Internal code
Part Number 61 R-VV YY : Year : 01~09
61-VV : 10 for 1.0V YY WW X X WW : Week : 01~52, 52 represents
12 for 1.2V 52 and 53 week
X : Internal Code
15 for 1.5V
18 for 1.8V
25 for 2.5V
28 for 2.8V
33 for 3.3V

(7) SO-8EP

( Top View )
8 5
YY : Year : 08, 09,10~
Logo WW : Week : 01~52; 52
Part Number AP7361-VV represents 52 and 53 week
YY WW X X E X X : Internal Code
AP7361-10 for 1.0V SO-8-EP
AP7361-12 for 1.2V
1 4
AP7361-15 for 1.5V
AP7361-18 for 1.8V
AP7361-25 for 2.5V
AP7361-28 for 2.8V
AP7361-33 for 3.3V

AP7361 17 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Package Outline Dimensions (All dimensions in mm.)

Please see http://www.diodes.com/package-outlines.html for the latest version.

(1): U-DFN3030-8
U-DFN3030-8
Type E
A Dim Min Max Typ
A3 A 0.57 0.63 0.60
A1 A1 0 0.05 0.02
A3   0.15
D b 0.20 0.30 0.25
D2 D 2.95 3.05 3.00
L (x8) D2 2.15 2.35 2.25
E 2.95 3.05 3.00
e   0.65
E2 1.40 1.60 1.50
E E2
L 0.30 0.60 0.45
Z   0.40
All Dimensions in mm

Z (x4) e b (x8)

(2): SOT89-5
00
.2

D1
R0

C
SOT89-5
L
Dim Min Max Typ
A 1.40 1.60 1.50
H B 0.50 0.62 0.56
E
B1 0.44 0.54 0.48
C 0.35 0.43 0.38
D 4.40 4.60 4.50
L
D1 1.62 1.83 1.733
B1 E 2.40 2.60 2.50
B
e - - 1.50
e
H 3.95 4.25 4.10
8° (4x) L 0.65 0.95 0.80
All Dimensions in mm
A

(3): TO252
TO252
Dim Min Max Typ
E A A 2.19 2.39 2.29
b3 c2 A1 0.00 0.13 0.08
A2 0.97 1.17 1.07
L3 b 0.64 0.88 0.783
b2 0.76 1.14 0.95
E1 b3 5.21 5.46 5.33
A2 c2 0.45 0.58 0.531
D
H D 6.00 6.20 6.10
D1 5.21  
e   2.286
E 6.45 6.70 6.58
L4 A1 E1 4.32  
H 9.40 10.41 9.91
L L 1.40 1.78 1.59
e L3 0.88 1.27 1.08
2X b2 3X b L4 0.64 1.02 0.83
a
a 0° 10° 
All Dimensions in mm

AP7361 18 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361
Package Outline Dimensions (cont.) (All dimensions in mm.)
Please see http://www.diodes.com/package-outlines.html for the latest version.
(4): SOT223 and SOT223R

SOT223
Dim Min Max Typ
A 1.55 1.65 1.60
A1 0.010 0.15 0.05
b1 2.90 3.10 3.00
b2 0.60 0.80 0.70
C 0.20 0.30 0.25
D 6.45 6.55 6.50
E 3.45 3.55 3.50
E1 6.90 7.10 7.00
e — — 4.60
e1 — — 2.30
A
L 0.85 1.05 0.95
Q 0.84 0.94 0.89
A1 All Dimensions in mm

(5): SO-8EP

Exposed Pad
8 5
SO-8EP (SOP-8L-EP)
E1
Dim Min Max Typ
H A 1.40 1.50 1.45
1 4 A1 0.00 0.13 -
F b 0.30 0.50 0.40
C 0.15 0.25 0.20
b D 4.85 4.95 4.90
Bottom View
E 3.80 3.90 3.85
E E0 3.85 3.95 3.90
9° (All sides) N
45° E1 5.90 6.10 6.00
7°
Q e - - 1.27
A 4° ± 3° C
Gauge Plane F 2.75 3.35 3.05
Seating Plane H 2.11 2.71 2.41
e E0
A1
D L L 0.62 0.82 0.72
N - - 0.35
Q 0.60 0.70 0.65
All Dimensions in mm

AP7361 19 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Suggested Pad Layout

Please see http://www.diodes.com/package-outlines.html for the latest version.
(1): U-DFN3030-8

X (x8) C

Y
(x8)
Dimensions Value (in mm)
C 0.65
C1 2.35
Y1 Y2 X 0.30
Y 0.65
Y1 1.60
Y2 2.75

C1

(2): SOT89-5

C1
Value
Dimensions
(in mm)
X2 C 1.500
C1 1.050
Y3
Y2 X 0.680
Y1
X1 0.760
X2 1.930
X3 3.680
Y 1.200
Y X1
Y1 1.200
X
Y2 4.250
X3
Y3 4.500

(3): TO252

X2

Y2 Dimensions Value (in mm)

Z 11.6
Z X1 1.5
C
X2 7.0
Y1 2.5
Y1 Y2 7.0
C 6.9
E1 2.3

X1 E1

AP7361 20 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

Suggested Pad Layout (cont.)

Please see http://www.diodes.com/package-outlines.html for the latest version.
(4): SOT223 and SOT223R

X1

Y1 Dimensions Value (in mm)

X1 3.3
X2 1.2
C1 Y1 1.6
Y2 1.6
C1 6.4
C2 2.3
Y2

C2
X2

(5): SO-8EP

X2

Dimensions Value(in mm)

C 1.270
X 0.802
X1 3.502
Y1
Y2 X2 4.612
Y 1.505
X1
Y1 2.613
Y2 6.500

C X

AP7361 21 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated
 AP7361

IMPORTANT NOTICE

DIODES INCORPORATED MAKES NO WARRANTY OF ANY KIND, EXPRESS OR IMPLIED, WITH REGARDS TO THIS DOCUMENT,
INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
(AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION).

Diodes Incorporated and its subsidiaries reserve the right to make modifications, enhancements, improvements, corrections or other changes
without further notice to this document and any product described herein. Diodes Incorporated does not assume any liability arising out of the
application or use of this document or any product described herein; neither does Diodes Incorporated convey any license under its patent or
trademark rights, nor the rights of others. Any Customer or user of this document or products described herein in such applications shall assume
all risks of such use and will agree to hold Diodes Incorporated and all the companies whose products are represented on Diodes Incorporated
website, harmless against all damages.

Diodes Incorporated does not warrant or accept any liability whatsoever in respect of any products purchased through unauthorized sales channel.
Should Customers purchase or use Diodes Incorporated products for any unintended or unauthorized application, Customers shall indemnify and
hold Diodes Incorporated and its representatives harmless against all claims, damages, expenses, and attorney fees arising out of, directly or
indirectly, any claim of personal injury or death associated with such unintended or unauthorized application.

Products described herein may be covered by one or more United States, international or foreign patents pending. Product names and markings
noted herein may also be covered by one or more United States, international or foreign trademarks.

This document is written in English but may be translated into multiple languages for reference. Only the English version of this document is the
final and determinative format released by Diodes Incorporated.

LIFE SUPPORT

Diodes Incorporated products are specifically not authorized for use as critical components in life support devices or systems without the express
written approval of the Chief Executive Officer of Diodes Incorporated. As used herein:

A. Life support devices or systems are devices or systems which:

1. are intended to implant into the body, or

2. support or sustain life and whose failure to perform when properly used in accordance with instructions for use provided in the
labeling can be reasonably expected to result in significant injury to the user.

B. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or to affect its safety or effectiveness.

Customers represent that they have all necessary expertise in the safety and regulatory ramifications of their life support devices or systems, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any
use of Diodes Incorporated products in such safety-critical, life support devices or systems, notwithstanding any devices- or systems-related
information or support that may be provided by Diodes Incorporated. Further, Customers must fully indemnify Diodes Incorporated and its
representatives against any damages arising out of the use of Diodes Incorporated products in such safety-critical, life support devices or systems.

Copyright © 2017, Diodes Incorporated

www.diodes.com

AP7361 22 of 22 March 2017

Document number: DS33626 Rev. 11 - 3 www.diodes.com © Diodes Incorporated