SPECIFICATIONS

1. MAJOR COMPONENT

Tool box Fuel tank Hydraulic tank Main pump

Engine

Radiator
Tooth Bucket Turning joint Swing motor Main control valve Oil cooler

Arm Arm cylinder Boom Boom cylinder Cab Precleaner Counterweight

Swing
bearing

Bucket cylinder Connecting link Idler Upper roller Sprocket

Side cutter Connecting rod Lower roller Track Travel motor

300SG2SP01

2-1
 2. SPECIFICATIONS

1) HX300SG, MONO BOOM

I (I') D
C

G (G')

E
F

H
J M
K N
A B (L)

300SG2SP02A

Unit Specification
Boom 6.25 (20' 6")
Description m (ft-in)
Arm 3.05 (10' 0") 2.10 (6' 11'') 2.50 (8' 2'') 3.75 (12' 4'')
mm (in) Shoe 600 (24") 600 (24") 600 (24") 600 (24")
Operating weight kg (lb) 29540 (65125) 29340 (64684) 29530 (65103) 29850 (65808)
Bucket capacity (SAE heaped), standard m³ (yd³) 1.27 (1.66) 1.27 (1.66) 1.27 (1.66) 1.27 (1.66)
Overall length A 10590 (34' 9'') 10750 (35' 3'') 10700 (35' 1'') 10670 (35' 0'')
Overall width B 3200 (10' 6'') 3200 (10' 6'') 3200 (10' 6'') 3200 (10' 6'')
Overall height of boom C 3330 (10' 11'') 3660 (12' 0'') 3520 (11' 7'') 3530 (11' 7'')
Superstructure width D 2980 (9' 9'') 2980 (9' 9'') 2980 (9' 9'') 2980 (9' 9'')
Overall height of cab E 3100 (10' 2'') 3100 (10' 2'') 3100 (10' 2'') 3100 (10' 2'')
Ground clearance of counterweight F 1190 (3' 11'') 1190 (3' 11'') 1190 (3' 11'') 1190 (3' 11'')
Overall height of engine hood G 3190 (10' 6'') 3190 (10' 6'') 3190 (10' 6'') 3190 (10' 6'')
Overall height of handrail G' 3100 (10' 2'') 3100 (10' 2'') 3100 (10' 2'') 3100 (10' 2'')
mm (ft-in)
Minimum ground clearance H 500 (1' 8'') 500 (1' 8'') 500 (1' 8'') 500 (1' 8'')
Rear-end distance I 3120 (10' 3'') 3120 (10' 3'') 3120 (10' 3'') 3120 (10' 3'')
Rear-end swing radius I' 3200 (10' 6'') 3200 (10' 6'') 3200 (10' 6'') 3200 (10' 6'')
Distance between tumblers J 4030 (13' 3'') 4030 (13' 3'') 4030 (13' 3'') 4030 (13' 3'')
Undercarriage length K 4940 (16' 2'') 4940 (16' 2'') 4940 (16' 2'') 4940 (16' 2'')
Undercarriage width L 3200 (10' 6'') 3200 (10' 6'') 3200 (10' 6'') 3200 (10' 6'')
Track gauge M 2600 (8' 6'') 2600 (8' 6'') 2600 (8' 6'') 2600 (8' 6'')
Track shoe width, standard N 600 (2' 0") 600 (2' 0") 600 (2' 0") 600 (2' 0")
Travel speed (low/high) km/hr (mph) 3.2/5.7 (2.0/3.5) 3.2/5.7 (2.0/3.5) 3.2/5.7 (2.0/3.5) 3.2/5.7 (2.0/3.5)
Swing speed rpm 11.1 11.1 11.1 11.1
Gradeability Degree (%) 35 (70) 35 (70) 35 (70) 35 (70)
Ground pressure kgf/cm² (psi) 0.57 (8.11) 0.57 (8.11) 0.57 (8.11) 0.57 (8.11)
Maximum traction force kgf (lbf) 25800 (56880) 25800 (56880) 25800 (56880) 25800 (56880)
2-2
 2) HX300SG, LONG REACH

I (I') D

G (G')
C

E
F

H
J M
K N
A B (L)

300SG2SP03A

Unit Specification
Boom 10.2 (33' 6")
Description m (ft-in)
Arm 7.85 (25' 9")
mm (in) Shoe 800 (32")
Operating weight kg (lb) 32610 (71893)
Bucket capacity (SAE heaped), standard m³ (yd³) 0.52 (0.68)
Overall length A 14550 (47' 9")
Overall width B 3400 (11' 2")
Overall height of boom C 3550 (11' 8")
Superstructure width D 2980 (9' 9")
Overall height of cab E 3100 (10' 2")
Ground clearance of counterweight F 1190 (3' 11")
Overall height of engine hood G 3190 (10' 6")
Overall height of handrail G' 3100 (10' 2")
mm (ft-in)
Minimum ground clearance H 500 (1' 8")
Rear-end distance I 3120 (10' 3")
Rear-end swing radius I' 3200 (10' 6")
Distance between tumblers J 4030 (13' 3")
Undercarriage length K 4940 (16' 2")
Undercarriage width L 3200 (10' 6")
Track gauge M 2600 (8' 6")
Track shoe width, standard N 800 (2' 7")
Travel speed (low/high) km/hr (mph) 3.2/5.7 (2.0/3.5)
Swing speed rpm 11.1
Gradeability Degree (%) 35 (70)
Ground pressure kgf/cm² (psi) 0.47 (6.68)
Maximum traction force kgf (lbf) 25800 (56880)

2-3
 3. WORKING RANGE AND DIGGING FORCE

1) HX300SG, MONO BOOM

A
A'
F
D
E
C
B'
B

8 ft
300SG2SP04

Boom 6.25 (20' 6")

Description m (ft-in)
Arm 3.05 (10' 0") 2.10 (6' 11") 2.50 (8' 2") 3.75 (12' 4")
Max digging reach A 10810 (35' 6") 10040 (32' 11") 10310 (33' 10") 11420 (37' 6")
Max digging reach on ground A' 10610 (34' 10") 9820 (32' 3") 10100 (33' 2") 11230 (36' 10")
Max digging depth B 7330 (24' 1") 6380 (20' 11") 6780 (22' 3") 8030 (26' 4")
Max digging depth (8 ft level) mm B' 7170 (23' 6") 6180 (20' 3") 6600 (21' 8") 7890 (25' 11")
Max vertical wall digging depth (ft-in) C 6280 (20' 7") 5910 (19' 5") 5760 (18' 11") 6990 (22' 11")
Max digging height D 10200 (33' 6") 10130 (33' 3") 9980 (32' 9") 10410 (34' 2")
Max dumping height E 7150 (23' 5") 6990 (22' 11") 6930 (22' 9") 7360 (24' 2")
Min swing radius F 4270 (14' 0") 4420 (14' 6") 4320 (14' 2") 4220 (13' 10")
kN 169 [184] 169 [184] 169 [184] 169 [184]
kgf SAE 17200 [18760] 17200 [18760] 17200 [18760] 17200 [18760]
lbf 37920 [41370] 37920 [41370] 37920 [41370] 37920 [41370]
Bucket digging force
kN 192 [210] 192 [210] 192 [210] 192 [210]
kgf ISO 19600 [21380] 19600 [21380] 19600 [21380] 19600 [21380]
lbf 43210 [47140] 43210 [47140] 43210 [47140] 43210 [47140]
kN 124 [135] 170 [185] 147 [161] 109 [119]
kgf SAE 12600 [13750] 17300 [18870] 15000 [16360] 11100 [12110]
lbf 27780 [30310] 38140 [41610] 33070 [36080] 24470 [26690]
Arm digging force
kN 129 [140] 178 [194] 154 [168] 112 [122]
kgf ISO 13100 [14290] 18100 [19750] 15700 [17130] 11400 [12440]
lbf 28880 [31510] 39900 [43530] 34610 [37760] 25130 [27410]
[ ] : Power boost

2-4
 2) HX300SG, LONG REACH

A
A'
F

D
E
C
B'
B

8ft
300SG2SP05

Boom 10.2 (33' 6")

Description m (ft-in)
Arm 7.85 (25' 9")
Max digging reach A 18530 (60' 10")
Max digging reach on ground A' 18410 (60' 5")
Max digging depth B 14740 (48' 4")
Max digging depth (8 ft level) mm B' 14660 (48' 1")
Max vertical wall digging depth (ft-in) C 13700 (44' 11")
Max digging height D 14590 (47' 10")
Max dumping height E 12270 (40' 3")
Min swing radius F 6270 (20' 7")
kN 70 [76]
kgf SAE 7100 [7750]
lbf 15650 [17090]
Bucket digging force
kN 80 [88]
kgf ISO 8200 [8950]
lbf 18080 [19730]
kN 43 [47]
kgf SAE 4420 [4820]
lbf 9740 [10630]
Arm digging force
kN 44 [48]
kgf ISO 4500 [4910]
lbf 9920 [10830]
[ ] : Power boost

2-5
 4. WEIGHT

HX300SG HX300SG Long reach

Item
kg lb kg lb
Upperstructure assembly
·Main frame weld assembly 2361 5210 2361 5210
·Engine assembly 485 1069 485 1069
·Main pump assembly 133 293 133 293
·Main control valve assembly 230 507 230 507
·Swing motor assembly 408 900 408 900
·Hydraulic oil tank assembly 224 494 224 494
·Fuel tank assembly 275 606 275 606
·Counterweight 5200 11460 7000 15450
·Cab assembly 310 680 310 680
Lower chassis assembly
·Track frame weld assembly 3765 8300 3765 8300
·Swing bearing 433 950 433 950
·Travel motor assembly 433 950 433 950
·Turning joint 38 84 38 84
·Sprocket (2 EA) 141 311 141 311
·Track recoil spring (2 EA) 450 992 450 992
·Idler (2 EA) 500 1102 500 1102
·Upper roller (4 EA) 140 309 140 309
·Lower roller (18 EA) 972 2143 972 2143
·Track-chain assembly
3758 8285 - -
(600 mm triple grouser shoe) (2 EA)
·Track-chain assembly
3758 8285 4706 10375
(800 mm triple grouser shoe) (2 EA)
Front attachment assembly
·6.25 m boom assembly 2200 4860 - -
·3.05 m arm assembly 1025 2260 - -
·1.27 m³ SAE heaped bucket 1010 2230 - -
·10.2 m boom assembly - - 2960 6530
·7.85 m arm assembly - - 1340 2960
·0.52 m³ SAE heaped bucket - - 460 1010
·Boom cylinder assembly 263 580 263 580
·Arm cylinder assembly 368 811 368 811
·1.27 m³ bucket cylinder assembly 224 494 - -
·0.52 m³ bucket cylinder assembly - - 103 227
·Bucket control linkage total 112 248 112 248
※ This information is different with operating and transportation weight because it is not including har-
ness, pipe, oil, fuel so on.
※ Refer to Transportation for actual weight information and Specifications for operating weight.

2-6
 5. LIFTING CAPACITIES

Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger

MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HX300SG
BOOM 6250 2100 5200 600 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *7150 *7150 *7350 7030 6.40
(24.6 ft) lb *15760 *15760 *16200 15500 (21.0)
6.0 m kg *7360 *7360 *7240 5430 7.44
(19.7 ft) lb *16230 *16230 *15960 11970 (24.4)
4.5 m kg *8330 7420 *7370 5280 7290 4670 8.06
(14.8 ft) lb *18360 16360 *16250 11640 16070 10300 (26.5)
3.0 m kg *9550 7010 *7900 5100 6770 4310 8.37
(9.8 ft) lb *21050 15450 *17420 11240 14930 9500 (27.5)
1.5 m kg *10560 6700 7850 4940 6640 4210 8.40
(4.9 ft) lb *23280 14770 17310 10890 14640 9280 (27.6)
0.0 m kg 10810 6550 7750 4840 6890 4350 8.16
(0.0 ft) lb 23830 14440 17090 10670 15190 9590 (26.8)
-1.5 m kg *14440 9990 10800 6540 7780 4870 7650 4800 7.60
(-4.9 ft) lb *31830 22020 23810 14420 17150 10740 16870 10580 (24.9)
-3.0 m kg *17130 *17130 *13040 10180 *9850 6690 *8410 5860 6.66
(-9.8 ft) lb *37770 *37770 *28750 22440 *21720 14750 *18540 12920 (21.9)
-4.5 m kg *9810 *9810 *8120 *8120 5.12
(-14.8 ft) lb *21630 *21630 *17900 *17900 (16.8)

Note 1. Lifting capacity are based on ISO 10567.

2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause serious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

2-7
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HX300SG
BOOM 6250 2500 5200 600 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *6510 *6510 *6350 *6350 6.74
(24.6 ft) lb *14350 *14350 *14000 *14000 (22.1)
6.0 m kg *6870 *6870 *6670 5440 *6040 5140 7.74
(19.7 ft) lb *15150 *15150 *14700 11990 *13320 11330 (25.4)
4.5 m kg *9930 *9930 *7880 7490 *6990 5310 *6030 4450 8.34
(14.8 ft) lb *21890 *21890 *17370 16510 *15410 11710 *13290 9810 (27.4)
3.0 m kg *12770 10610 *9150 7060 *7600 5110 *6240 4110 8.64
(9.8 ft) lb *28150 23390 *20170 15560 *16760 11270 *13760 9060 (28.3)
1.5 m kg *10270 6710 7850 4920 6320 4000 8.67
(4.9 ft) lb *22640 14790 17310 10850 13930 8820 (28.4)
0.0 m kg *15040 9840 10790 6520 7710 4800 6530 4110 8.43
(0.0 ft) lb *33160 21690 23790 14370 17000 10580 14400 9060 (27.7)
-1.5 m kg *10480 *10480 *14670 9870 10730 6470 7690 4790 7170 4490 7.89
(-4.9 ft) lb *23100 *23100 *32340 21760 23660 14260 16950 10560 15810 9900 (25.9)
-3.0 m kg *18430 *18430 *13520 10030 *10200 6570 *8350 5380 6.99
(-9.8 ft) lb *40630 *40630 *29810 22110 *22490 14480 *18410 11860 (22.9)
-4.5 m kg *14820 *14820 *10960 10410 *8540 7690 5.55
(-14.8 ft) lb *32670 *32670 *24160 22950 *18830 16950 (18.2)

Note 1. Lifting capacity are based on ISO 10567.

2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause serious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

2-8
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HX300SG
BOOM 6250 3050 5200 600 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) 9.0 m (29.5 ft) Capacity Reach
height (A)
m (ft)
7.5 m kg *4120 *4120 7.38
(24.6 ft) lb *9080 *9080 (24.2)
6.0 m kg *6020 5510 *3940 *3940 8.30
(19.7 ft) lb *13270 12150 *8690 *8690 (27.2)
4.5 m kg *8800 *8800 *7220 *7220 *6480 5350 *3930 *3930 8.86
(14.8 ft) lb *19400 *19400 *15920 *15920 *14290 11790 *8660 *8660 (29.1)
3.0 m kg *11640 10880 *8560 7140 *7170 5130 *5140 3850 *4060 3740 9.14
(9.8 ft) lb *25660 23990 *18870 15740 *15810 11310 *11330 8490 *8950 8250 (30.0)
1.5 m kg *13860 10120 *9800 6740 7840 4910 *5800 3750 *4340 3640 9.17
(4.9 ft) lb *30560 22310 *21610 14860 17280 10820 *12790 8270 *9570 8020 (30.1)
0.0 m kg *14820 9790 *10630 6490 7670 4760 *4830 3720 8.94
(0.0 ft) lb *32670 21580 *23440 14310 16910 10490 *10650 8200 (29.3)
-1.5 m kg *10440 *10440 *14830 9740 10650 6390 7600 4690 *5670 4010 8.44
(-4.9 ft) lb *23020 *23020 *32690 21470 23480 14090 16760 10340 *12500 8840 (27.7)
-3.0 m kg *16850 *16850 *14030 9850 *10490 6430 7680 4760 *7280 4680 7.61
(-9.8 ft) lb *37150 *37150 *30930 21720 *23130 14180 16930 10490 *16050 10320 (25.0)
-4.5 m kg *16800 *16800 *12100 10140 *8850 6670 *8160 6240 6.32
(-14.8 ft) lb *37040 *37040 *26680 22350 *19510 14700 *17990 13760 (20.7)

Note 1. Lifting capacity are based on ISO 10567.

2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause serious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

2-9
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger
MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
HX300SG
BOOM 6250 3750 5200 600 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) 9.0 m (29.5 ft) Capacity Reach
height (A)
m (ft)
9.0 m kg *3570 *3570 6.87
(29.5 ft) lb *7870 *7870 (22.6)
7.5 m kg *4790 *4790 *3260 *3260 8.14
(24.6 ft) lb *10560 *10560 *7190 *7190 (26.7)
6.0 m kg *5290 *5290 *3140 *3140 8.97
(19.7 ft) lb *11660 *11660 *6920 *6920 (29.4)
4.5 m kg *6340 *6340 *5830 5430 *4900 3990 *3140 *3140 9.50
(14.8 ft) lb *13980 *13980 *12850 11970 *10800 8800 *6920 *6920 (31.2)
3.0 m kg *10190 *10190 *7750 7280 *6590 5180 *5990 3860 *3250 *3250 9.76
(9.8 ft) lb *22470 *22470 *17090 16050 *14530 11420 *13210 8510 *7170 *7170 (32.0)
1.5 m kg *12770 10320 *9140 6820 *7380 4920 5940 3730 *3470 3260 9.79
(4.9 ft) lb *28150 22750 *20150 15040 *16270 10850 13100 8220 *7650 7190 (32.1)
0.0 m kg *6390 *6390 *14290 9810 *10190 6480 7650 4730 5820 3630 *3830 3310 9.58
(0.0 ft) lb *14090 *14090 *31500 21630 *22470 14290 16870 10430 12830 8000 *8440 7300 (31.4)
-1.5 m kg *6630 *6630 *9930 *9930 *14790 9620 10580 6310 7520 4610 *5340 3580 *4440 3530 9.11
(-4.9 ft) lb *14620 *14620 *21890 *21890 *32610 21210 23320 13910 16580 10160 *11770 7890 *9790 7780 (29.9)
-3.0 m kg *10420 *10420 *14550 *14550 *14440 9650 10550 6290 7520 4610 *5520 4010 8.35
(-9.8 ft) lb *22970 *22970 *32080 *32080 *31830 21270 23260 13870 16580 10160 *12170 8840 (27.4)
-4.5 m kg *15040 *15040 *18840 *18840 *13120 9850 *9740 6420 *7630 5040 7.19
(-14.8 ft) lb *33160 *33160 *41540 *41540 *28920 21720 *21470 14150 *16820 11110 (23.6)
-6.0 m kg *14260 *14260 *10040 *10040 *8020 7950 5.38
(-19.7 ft) lb *31440 *31440 *22130 *22130 *17680 17530 (17.6)

Note 1. Lifting capacity are based on ISO 10567.

2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause serious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

2-10
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger

HX300SG MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
Long reach BOOM 10200 7850 7000 800 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 1.5 m (4.9 ft) 3.0 m (9.8 ft) 4.5 m (14.8 ft) 6.0 m (19.7 ft) 7.5 m (24.6 ft) 9.0 m (29.5 ft) Capacity Reach
height (A)
m (ft)
3.0 m kg *7270 *7270 *4130 *4130 *3510 *3510 *860 *860 17.26
(9.8 ft) lb *16030 *16030 *9110 *9110 *7740 *7740 *1900 *1900 (56.6)
1.5 m kg *4330 *4330 *6440 *6440 *4920 *4920 *4040 *4040 *910 *910 17.27
(4.9 ft) lb *9550 *9550 *14200 *14200 *10850 *10850 *8910 *8910 *2010 *2010 (56.7)
0.0 m kg *1390 *1390 *3240 *3240 *7450 6590 *5610 4960 *4530 3900 *970 *970 17.15
(0.0 ft) lb *3060 *3060 *7140 *7140 *16420 14530 *12370 10930 *9990 8600 *2140 *2140 (56.3)
-1.5 m kg *1450 *1450 *1960 *1960 *3330 *3330 *6240 6110 *6160 4600 *4950 3620 *1050 *1050 16.90
(-4.9 ft) lb *3200 *3200 *4320 *4320 *7340 *7340 *13760 13470 *13580 10140 *10910 7980 *2310 *2310 (55.4)
-3.0 m kg *2110 *2110 *2620 *2620 *3800 *3800 *6180 5850 *6560 4360 *5270 3430 *1170 *1170 16.51
(-9.8 ft) lb *4650 *4650 *5780 *5780 *8380 *8380 *13620 12900 *14460 9610 *11620 7560 *2580 *2580 (54.2)
-4.5 m kg *2790 *2790 *3340 *3340 *4470 *4470 *6670 5750 *6800 4230 *5490 3320 *1310 *1310 15.96
(-14.8 ft) lb *6150 *6150 *7360 *7360 *9850 *9850 *14700 12680 *14990 9330 *12100 7320 *2890 *2890 (52.4)
-6.0 m kg *3510 *3510 *4130 *4130 *5310 *5310 *7520 5750 *6890 4200 *5600 3270 *1520 *1520 15.25
(-19.7 ft) lb *7740 *7740 *9110 *9110 *11710 *11710 *16580 12680 *15190 9260 *12350 7210 *3350 *3350 (50.0)
-7.5 m kg *4290 *4290 *5010 *5010 *6320 *6320 *8650 5830 *6830 4230 *5590 3280 *1830 1750 14.34
(-24.6 ft) lb *9460 *9460 *11050 *11050 *13930 *13930 *19070 12850 *15060 9330 *12320 7230 *4030 3860 (47.0)
-9.0 m kg *5160 *5160 *6030 *6030 *7570 *7570 *8260 6000 *6590 4330 *5420 3350 *2310 2030 13.19
(-29.5 ft) lb *11380 *11380 *13290 *13290 *16690 *16690 *18210 13230 *14530 9550 *11950 7390 *5090 4480 (43.3)
-10.5 m kg *6140 *6140 *7250 *7250 *9180 *9180 *7610 6240 *6120 4510 *5030 3500 *3210 2480 11.74
(-34.4 ft) lb *13540 *13540 *15980 *15980 *20240 *20240 *16780 13760 *13490 9940 *11090 7720 *7080 5470 (38.5)
-12.0 m kg *8780 *8780 *8430 *8430 *6570 *6570 *5290 4790 *4280 3740 *3750 3340 9.86
(-39.4 ft) lb *19360 *19360 *18580 *18580 *14480 *14480 *11660 10560 *9440 8250 *8270 7360 (32.3)

Note 1. Lifting capacity are based on ISO 10567.

2. Lifting capacity of the HX series does not exceed 75% of tipping load with the machine on firm,
level ground or 87% of full hydraulic capacity.
3. The Lift-point is bucket pivot mounting pin on the arm (without bucket mass).
4. *Indicates load limited by hydraulic capacity.
※ Lifting capacities are based upon a standard machine conditions.
Lifting capacities will vary with different work tools, ground conditions and attachments.
The difference between the weight of a work tool attachment must be subtracted.
Consult with your local HD Hyundai Construction Equipment dealer regarding the lifting capaci-
ties for specific work tools and attachments.
Failure to comply to the rated load can cause serious injury, death, or property damage. Make
adjustments to the rated load as necessory for non-standard configurations.

2-11
 Model Type Boom Arm Counterweight Shoe Wheel Dozer Outrigger

HX300SG MONO Length [mm] Length [mm] weight [kg] width [mm] width [mm] Front Rear Front Rear
Long reach BOOM 10200 7850 7000 800 - - - - -

· : Rating over-front · : Rating over-side or 360 degree A

Lift-point radius (B) At max. reach

Lift-point 10.5 m (34.4 ft) 12.0 m (39.4 ft) 13.5 m (44.3 ft) 15.0 m (44.3 ft) 16.5 m (54.1 ft) Capacity Reach
height (A)
m (ft)
13.5 m kg *900 *900 12.91
(44.3 ft) lb *1980 *1980 (42.4)
12.0 m kg *1170 *1170 *850 *850 14.12
(39.4 ft) lb *2580 *2580 *1870 *1870 (46.3)
10.5 m kg *1470 *1470 *860 *860 *810 *810 15.07
(34.4 ft) lb *3240 *3240 *1900 *1900 *1790 *1790 (49.4)
9.0 m kg *1670 *1670 *1260 *1260 *800 *800 15.82
(29.5 ft) lb *3680 *3680 *2780 *2780 *1760 *1760 (51.9)
7.5 m kg *1850 *1850 *1520 *1520 *790 *790 16.40
(24.6 ft) lb *4080 *4080 *3350 *3350 *1740 *1740 (53.8)
6.0 m kg *2220 *2220 *2060 *2060 *1730 *1730 *1060 *1060 *800 *800 16.83
(19.7 ft) lb *4890 *4890 *4540 *4540 *3810 *3810 *2340 *2340 *1760 *1760 (55.2)
4.5 m kg *2740 *2740 *2560 *2560 *2330 *2330 *1950 *1950 *1290 *1290 *830 *830 17.11
(14.8 ft) lb *6040 *6040 *5640 *5640 *5140 *5140 *4300 *4300 *2840 *2840 *1830 *1830 (56.1)
3.0 m kg *3100 *3100 *2820 *2820 *2620 2380 *2180 1940 *1460 *1460 *860 *860 17.26
(9.8 ft) lb *6830 *6830 *6220 *6220 *5780 5250 *4810 4280 *3220 *3220 *1900 *1900 (56.6)
1.5 m kg *3470 3380 *3090 2740 *2820 2240 *2430 1850 *1570 1520 *910 *910 17.27
(4.9 ft) lb *7650 7450 *6810 6040 *6220 4940 *5360 4080 *3460 3350 *2010 *2010 (56.7)
0.0 m kg *3830 3140 *3360 2560 *3020 2120 *2670 1760 *1600 1470 *970 *970 17.15
(0.0 ft) lb *8440 6920 *7410 5640 *6660 4670 *5890 3880 *3530 3240 *2140 *2140 (56.3)
-1.5 m kg *4150 2940 *3600 2420 *3200 2010 *2850 1690 *1500 1420 *1050 *1050 16.90
(-4.9 ft) lb *9150 6480 *7940 5340 *7050 4430 *6280 3730 *3310 3130 *2310 *2310 (55.4)
-3.0 m kg *4410 2790 *3800 2300 3310 1930 2840 1630 *1170 *1170 *1170 *1170 16.51
(-9.8 ft) lb *9720 6150 *8380 5070 7300 4250 6260 3590 *2580 *2580 *2580 *2580 (54.2)
-4.5 m kg *4600 2690 3840 2230 3260 1880 *2620 1600 *1310 *1310 15.96
(-14.8 ft) lb *10140 5930 8470 4920 7190 4140 *5780 3530 *2890 *2890 (52.4)
-6.0 m kg 4570 2640 3800 2200 3240 1860 *1920 1610 *1520 *1520 15.25
(-19.7 ft) lb 10080 5820 8380 4850 7140 4100 *4230 3550 *3350 *3350 (50.0)
-7.5 m kg 4570 2650 3810 2210 3270 1890 *1830 1750 14.34
(-24.6 ft) lb 10080 5840 8400 4870 7210 4170 *4030 3860 (47.0)
-9.0 m kg *4550 2710 *3850 2270 *2310 2030 13.19
(-29.5 ft) lb *10030 5970 *8490 5000 *5090 4480 (43.3)
-10.5 m kg *4180 2850 *3210 2480 11.74
(-34.4 ft) lb *9220 6280 *7080 5470 (38.5)

2-11-1
 6. BUCKET SELECTION GUIDE

1) GENERAL BUCKET

1.27 SAE ★0.52 m3 SAE

heaped bucket heaped bucket

Recommendation
Capacity Width 10.2 m
6.25 m (20' 6") boom (33' 6")
Weight boom
Without With 2.1 m 2.5 m 3.05 m 3.75 m 7.85 m
SAE CECE
side side arm arm arm arm arm
heaped heaped
cutter cutter (6' 11") (8' 2") (10' 0") (12' 4") (25' 9")

1.27 m3 1.11 m3 1325 mm 1410 mm 1135 kg

● ● ◐ ■ X
(1.66 yd3) (1.45 yd3) (52") (56") (2500 lb)

★ 0.52 m3 0.45 m3 945 mm 1035 mm 470 kg

X X X X ◐
(0.68 yd3) (0.59 yd3) (37") (41") (1040 lb)

★ : Long reach bucket

● Applicable for materials with density of 2100 kg/m3 (3500 lb/yd3) or less
◐ Applicable for materials with density of 1800 kg/m3 (3000 lb/yd3) or less
■ Applicable for materials with density of 1500 kg/m3 (2500 lb/yd3) or less
▲ Applicable for materials with density of 1200 kg/m3 (2000 lb/yd3) or less
X Not recommended
※ These recommendations are for general conditions and average use.
Work tools and ground conditions have effects on machine performance.
Select an optimum combination according to the working conditions and the type of work that is
being done.
Consult your HD Hyundai Construction Equipment dealer for information on selecting the
correct boom-arm
boom arm-bucket
bucket combination.

2-12
 2) HEAVY DUTY AND ROCK-HEAVY DUTY BUCKET

◈ 1.46 m3 SAE ◆ 1.50 m3 SAE

heaped bucket heaped bucket

Recommendation
Capacity Width 10.2 m
6.25 m (20' 6") boom (33' 6")
Weight boom
Without With 2.1 m 2.5 m 3.05 m 3.75 m 7.85 m
SAE CECE
side side arm arm arm arm arm
heaped heaped
cutter cutter (6' 11") (8' 2") (10' 0") (12' 4") (25' 9")

◈ 1.46 m3 1.28 m3 1535 mm 1395 kg

- ◐ ◐ ■ ▲ X
(1.91 yd3) (1.67 yd3) (60") (3080 lb)

◆ 1.50 m3 1.30 m 1550 mm 1575 kg

- ◐ ■ ■ ▲ X
(1.96 yd3) (1.70 yd3) (61") (3470 lb)

◈ : Heavy duty bucket

◆ : Rock-Heavy duty bucket

● Applicable for materials with density of 2100 kg/m3 (3500 lb/yd3) or less
◐ Applicable for materials with density of 1800 kg/m3 (3000 lb/yd3) or less
■ Applicable for materials with density of 1500 kg/m3 (2500 lb/yd3) or less
▲ Applicable for materials with density of 1200 kg/m3 (2000 lb/yd3) or less
X Not recommended

2-10-1
2-13
7. UNDERCARRIAGE

1) TRACKS
X-leg type center frame is integrally welded with reinforced box-section track frames. The design
includes dry tracks, lubricated rollers, idlers, sprockets, hydraulic track adjusters with shock absorb-
ing springs, and assembled track-type tractor shoes with triple grousers.

2) TYPES OF SHOES
Description Unit Triple grouser
Model
width mm (in) 600 (24") 700 (28") 800 (32")

Operating weight kg (lb) 29540 (65125) 30090 (66337) 30460 (67153)

HX300SG Ground pressure kgf/cm2 (psi) 0.57 (8.09) 0.50 (7.11) 0.44 (6.26)
Overall width mm (ft-in) 3200 (10' 6") 3300 (10' 10") 3400 (11' 1")
Operating weight kg (lb) - - 32610 (71893)
HX300SG
Ground pressure kgf/cm2 (psi) - - 0.47 (6.68)
Long reach
Overall width mm (ft-in) - - 3400 (11' 2")

3) NUMBER OF ROLLERS AND SHOES ON EACH SIDE

Item Quantity
Upper rollers 2 EA
Lower rollers 9 EA
Track shoes 48 EA

2-14
 4) SELECTION OF TRACK SHOE
Suitable track shoes should be selected according to operating conditions.
Method of selecting shoes
Confirm the category from the list of applications in table 22, then use table 1 to select the shoe.
Wide shoes (categories B and C) have limitations on applications. Before using wide shoes, check
the precautions, then investigate and study the operating conditions to confirm if these shoes are
suitable.
Select the narrowest shoe possible to meet the required flotation and ground pressure.
Application of wider shoes than recommendations will cause unexpected problem such as bending
of shoes, crack of link, breakage of pin, loosening of shoe bolts and the other various problems.

※ Table 1
Track shoe Specification Category

600 mm triple grouser Standard A

700 mm triple grouser Option B
800 mm triple grouser Option C
800 mm triple grouser (long reach) Standard C

※ Table 2
Category Applications Precautions

Rocky ground, · Travel at low speed on rough ground with large obstacles such as boul-
A river beds, ders or fallen trees or a wide range of general civil engineering work
normal soil

Normal soil, · These shoes cannot be used on rough ground with large obstacles
soft ground such as boulders or fallen trees
B · Travel at high speed only on flat ground
· Travel slowly at low speed if it is impossible to avoid going over obsta-
cles

Extremely soft ground · Use the shoes only in the conditions that the machine sinks and it is
(swampy ground) impossible to use the shoes of category A or B
· These shoes cannot be used on rough ground with large obstacles
C such as boulders or fallen trees
· Travel at high speed only on flat ground
· Travel slowly at low speed if it is impossible to avoid going over obsta-
cles

2-15
 8. SPECIFICATIONS FOR MAJOR COMPONENTS
1) ENGINE
Item Specification
Model HD Hyundai Construction Equipment / HE6.7
4-cycle, turbocharged, charge air cooled,
Type
electronic controlled diesel engine
Cooling method Water cooled
Number of cylinders and arrangement 6 cylinders, in-line
Firing order 1-5-3-6-2-4
Combustion chamber type Direct injection type
Cylinder bore×stroke 107×124 mm (4.21 "×4.88 ")
Piston displacement 6.7ℓ (408 cu in)
Compression ratio 17.2 : 1
Gross power 227 Hp (169 kW) at 1900rpm
Net power 197 Hp (147 kW) at 1900 rpm
Peak torque 952 N·m (702 lbf·ft) at 1400 rpm
Engine oil quantity 23.1ℓ (6.1 U.S. gal)
Wet weight 485 kg (1069 lb)
Starting motor 24 V - 4.8 kW
Alternator 24 V - 90 A
Battery 2×12V×150Ah

2) MAIN PUMP
Item Specification
Type Variable displacement tandem axis piston pumps
Capacity 2×140 cc/rev
Maximum pressure 330 kgf/cm2 (4690 psi) [360 kgf/cm2 (5120 psi)]
Rated oil flow 2×266ℓ/min (70.3 U.S. gpm/ 58.5 U.K. gpm)
[ ] : Power boost

3) GEAR PUMP
Item Specification
Type Fixed displacement gear pump single stage
Capacity 15 cc/rev
Maximum pressure 35 kgf/cm2 (500 psi)
Rated oil flow 28.5 ℓ/min (7.5 U.S. gpm/6.3 U.K. gpm)

2-16
 4) MAIN CONTROL VALVE
Specification
Item
HX300SG HX300SG Long reach
Type 10 spools
Operating method Hydraulic pilot system
Main relief valve pressure 330 kgf/cm2 (4695 psi) [360 kgf/cm2 (5120 psi)]
Boom 390 kgf/cm2 (5550 psi) 390 kgf/cm2 (5550 psi)
In : 230 kgf/cm2 (3270 psi)
Overload relief valve pressure Arm 390 kgf/cm2 (5550 psi)
Out : 260 kgf/cm2 (3700 psi)
Bucket 390 kgf/cm2 (5550 psi) 270 kgf/cm2 (3840 psi)
[ ] : Power boost

5) SWING MOTOR
Item Specification
Type Axial piston motor
Capacity 156.9 cc/rev
Relief pressure 300 kgf/cm2 (4267 psi)
Braking system Automatic, spring applied hydraulic released
Braking torque 84 kgf·m (608 lbf·ft)
Brake release pressure 22 kgf/cm2 (313 psi)
Reduction gear type 2 - stage planetary

6) TRAVEL MOTOR
Item Specification
Type Variable displacement axial piston motor
Relief pressure 350 kgf/cm2 (4978 psi)
Capacity (max/min) 282.6/156.9 cc/rev
Reduction gear type 2-stage planetary
Braking system Automatic, spring applied hydraulic released
Brake release pressure 11 kgf/cm2 (156 psi)
Braking torque 115 kgf·m (832 lbf·ft)

2-17
 7) REMOTE CONTROL VALVE
Item Specification
Type Pressure reducing type
Minimum 6.5 kgf/cm2 (92 psi)
Operating pressure
Maximum 25 kgf/cm2 (356 psi)
Lever 61 mm (2.4 in)
Single operation stroke
Pedal 123 mm (4.84 in)

8) CYLINDER
Item Specification
Bore dia×Rod dia×Stroke Ø140×Ø100×1465 mm
Boom cylinder
Cushion Extend only
Bore dia×Rod dia×Stroke Ø150×Ø110×1765 mm
Arm cylinder
Cushion Extend and retract
Bore dia×Rod dia×Stroke Ø140×Ø95×1185 mm
Bucket cylinder
Cushion Extend only
Bucket cylinder Bore dia×Rod dia×Stroke Ø100×Ø70×870 mm
(Long reach) Cushion Extend and retract
※ Discoloration of cylinder rod can occur when the friction reduction additive of lubrication oil spreads on
the rod surface.
※ Discoloration does not cause any harmful effect on the cylinder performance.

2-18
 9. RECOMMENDED OILS
HD Hyundai Construction Equipment genuine lubricating oils have been developed to offer the best
performance and service life for your equipment. These oils have been tested according to the specifi-
cations of HD Hyundai Construction Equipment and, therefore, will meet the highest safety and quality
requirements. We recommend that you use only HD Hyundai Construction Equipment genuine lubricat-
ing oils and grease officially approved by HD Hyundai Construction Equipment.

Service Ambient temperature˚C(˚F)

Capacity
Kind of fluid
point ℓ (U.S. gal) -50 -30 -20 -10 0 10 20 30 40
(-58) (-22) (-4) (14) (32) (50) (68) (86) (104)

★SAE 0W-30

Engine SAE 5W-30

Engine oil 23.1 (6.1)
oil pan SAE 10W-30
SAE 15W-40

Swing
11 (2.9) ★SAE 75W-90
drive
Gear oil
Final 7.8×2 SAE 80W-90
drive (2.1×2)
★ISO VG 15
Tank : 210
Hydraulic (55.5) ISO VG 32
Hydraulic oil
tank System : 320 ISO VG 46
(84.5)
ISO VG 68

★ASTM D975 NO.1

Fuel tank Diesel fuel 480 (126.8)
ASTM D975 NO.2

Fitting ★NLGI NO.1

(grease Grease As required
nipple) NLGI NO.2
Mixture of
Radiator Ethylene glycol base permanent type (50 : 50)
antifreeze
(reservoir 50 (13.2)
and soft ★Ethylene glycol base permanent type (60 : 40)
tank)
water★1
SAE : Society of Automotive Engineers ★ : Cold region
API : American Petroleum Institute Russia, CIS, Mongolia
ISO : International Organization for Standardization ★1 : Soft water
NLGI : National Lubricating Grease Institute City water or distilled water
ASTM : American Society of Testing and Material

※ Using any lubricating oils other than HD Hyundai Construction Equipment genuine products may lead to
a deterioration of performance and cause damage to major components.
※ Do not mix HD Hyundai Construction Equipment genuine oil with any other lubricating oil as it may result
in damage to the systems of major components.
※ For HD Hyundai Construction Equipment genuine lubricating oils and grease for use in regions with
extremely low temperatures, please contact HD Hyundai Construction Equipment dealers.

2-19