Professional Documents
Culture Documents
R5F364AEDFA
R5F364AEDFA
RENESAS MCU
1.
1.1
Overview
Features
The M16C/64A Group microcomputer (MCU) incorporates the M16C/60 Series CPU core and flash memory, employing sophisticated instructions for a high level of efficiency. This MCU has 1 MB of address space (expandable to 4 MB), and it is capable of executing instructions at high speed. In addition, the CPU core boasts a multiplier for high-speed operation processing. This MCU consumes little power, and supports operating modes that allow additional power control. The MCU also uses an anti-noise configuration to reduce emissions of electromagnetic noise and is designed to withstand electromagnetic interference (EMI). By integrating many of the peripheral functions, including the multifunction timer and serial interface, the number of system components has been reduced.
1.1.1
Applications
This MCU can be used in audio components, cameras, televisions, household appliances, office equipment, communication devices, mobile devices, industrial equipment, and other applications.
M16C/64A Group
1. Overview
1.2
Specifications
The M16C/64A Group includes100-pin package. Table 1.1 and Table 1.2 list specifications. Table 1.1
Item
CPU
Power-on reset 3 voltage detection points (selectable detection level from voltage
detection level 0 and volage detection level 1)
4 circuits: Main clock, sub clock, low-speed on-chip oscillator (125 kHz),
PLL frequency synthesizer
Frequency divider circuit: Divide ratio selectable from 1, 2, 4, 8, and 16 Power saving features: Wait mode, stop mode Real-time clock Address space: 1 MB External bus interface: 0 to 3 wait states, 4 chip select outputs, memory area
External Bus Bus and memory Expansion expansion expansion function (expandable to 4-MB), 3 V and 5 V interfaces
Bus format: Separate bus or multiplexed bus selectable, data bus width
selectable (8 or 16 bits), number of address buses selectable (12, 16, or 20)
I/O Ports
Interrupts
CMOS I/O ports: 85 (selectable pull-up resistors) N-channel open drain ports: 3 Interrupt vectors: 70 External interrupt inputs: 13 (NMI, INT 8, key input 4) Interrupt priority levels: 7
15-bit timer 1 (with prescaler) Automatic reset start function selectable
Watchdog Timer
DMA
DMAC
4 channels, cycle steal mode Trigger sources: 43 Transfer modes: 2 (single transfer, repeat transfer)
M16C/64A Group
1. Overview
Table 1.2
Item
Timer A
Timer B Three-phase motor control timer functions Timers Real-time clock PWM function
Three-phase inverter control (timer A1, timer A2, timer A4, timer B2) On-chip dead time timer
Count: second, minute, hour, day of week 8 bits 2
2 circuits 4 wave pattern matchings (differentiate wave pattern for headers, data
Remote control signal receiver 0, data 1, and special data)
Flash Memory
Program/erase power supply voltage: 2.7 to 5.5 V Program/erase cycles: 1,000 times (program ROM 1, program ROM
2), 10,000 times (data flash)
Notes: 1. IEBus is a registered trademark of NEC Electronics Corporation. 2. See Table 1.3 Product List for the operating temperature. 3. The CEC function indicates circuitry which supports the transmission and reception of CEC signals standardized by the High-Definition Multimedia Interface (HDMI). HDMI and High-Definition Multimedia Interface are registered trademarks of HDMI Licensing, LLC.
M16C/64A Group
1. Overview
1.3
Product List
Table 1.3 lists product information. Figure 1.1 shows the Part No., with Memory Size and Package, and Figure 1.2 shows the Marking Diagram (Top View). Table 1.3 Product List
Program ROM 1 128 KB ROM Capacity Program Data flash ROM 2 16 KB 4 KB 2 blocks RAM Capacity 12 KB Package Code Remarks
Part No. R5F364A6NFA R5F364A6NFB R5F364A6DFA R5F364A6DFB R5F364AENFA R5F364AENFB R5F364AEDFA R5F364AEDFB R5F364AMNFA R5F364AMNFB R5F364AMDFA R5F364AMDFB (P) (P) (P) (P) (P) (P) (D) (D) (P) (P) (P) (P)
256 KB
16 KB
4 KB 2 blocks
20 KB
512 KB
16 KB
4 KB 2 blocks
31 KB
PRQP0100JD-B Operating temperature PLQP0100KB-A -20C to 85C PRQP0100JD-B Operating temperature PLQP0100KB-A -40C to 85C PRQP0100JD-B Operating temperature PLQP0100KB-A -20C to 85C PRQP0100JD-B Operating temperature PLQP0100KB-A -40C to 85C PRQP0100JD-B Operating temperature PLQP0100KB-A -20C to 85C PRQP0100JD-B Operating temperature PLQP0100KB-A -40C to 85C
(D): Under development (P): Planning Note: 1. Previous package codes are as follows: PRQP0100JD-B: 100P6F-A PLQP0100KB-A: 100P6Q-A
M16C/64A Group
1. Overview
Part No. R 5 F 3
6 4 A 6 D FA
Package type FA: Package PRQP0100JD-B (100P6F-A) FB: Package PLQP0100KB-A (100P6Q-A) Property Code N: Operating temperature: -20C to 85C D: Operating temperature: -40C to 85C Memory capacity Program ROM 1/RAM 6: 128 KB/12 KB E: 256 KB/20 KB M: 512 KB/31 KB M16C/64A Group (100 pins) 16-bit MCU Memory type F: Flash memory Renesas MCU Renesas semiconductor
Figure 1.1
M1 6 C R 5 F 3 6 5 0 6 DF A XXXXXXX
Type No. (See Figure 1.1 Part No., Memory Size, and Package.) Seven digit date code
Figure 1.2
M16C/64A Group
1. Overview
1.4
Block Diagram
8 Port P0
8 Port P1
8 Port P1
8 Port P3
8 Port P4
8 Port P5
VCC2 ports
UART or clock synchronous serial I/O (6 channels) Clock synchronous serial I/O
(8-bit x 2 channels) Multi-master I2C-bus interface
System clock generator XIN-XOUT XCIN-XCOUT PLL frequency synthesizer On-chip oscillator (125 kHz) DMAC (4 channels) CRC arithmetic circuit (CRC-CCITT or CRC-16) Voltage detector Power-on reset On-chip debugger
Multiplier
VCC1 ports
Port P10 8
Port P9 8
Port P8 8
Port P7 8
Port P6 8
Notes: 1. ROM size depends on MCU type. 2. RAM size depends on MCU type.
Figure 1.3
M16C/64A Group
1. Overview
1.5
Pin Assignments
Figure 1.4 and Figure 1.5 show pin assignments. Table 1.4 and Table 1.5 list pin names.
(See Note 3) P1_0/CTS6/RTS6/D8 P1_1/CLK6/D9 P1_2/RXD6/SCL6/D10 P1_3/TXD6/SDA6/D11 P1_4/D12 P1_5/INT3/IDV/D13 P1_6/INT4/IDW/D14 P1_7/INT5/IDU/D15 P2_0/AN2_0/A0, [A0/D0], A0 P2_1/AN2_1/A1, [A1/D1], [A1/D0] P2_2/AN2_2/A2, [A2/D2], [A2/D1] P2_3/AN2_3/A3, [A3/D3], [A3/D2] P2_4/INT6/AN2_4/A4, [A4/D4], [A4/D3] P2_5/INT7/AN2_5/A5, [A5/D5], [A5/D4] P2_6/AN2_6/A6, [A6/D6], [A6/D5] P2_7/AN2_7/A7, [A7/D7], [A7/D6] VSS P3_0/A8 [A8/D7] VCC2 P3_1/A9 P3_2/A10 P3_3/A11 P3_4/A12 P3_5/A13 P3_6/A14 P3_7/A15 P4_0/A16 P4_1/A17 P4_2/A18 P4_3/A19 80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
P0_7/AN0_7/D7 P0_6/AN0_6/D6 P0_5/AN0_5/D5 P0_4/AN0_4/D4 P0_3/AN0_3/D3 P0_2/AN0_2/D2 P0_1/AN0_1/D1 P0_0/AN0_0/D0 P10_7/AN7/KI3 P10_6/AN6/KI2 P10_5/AN5/KI1 P10_4/AN4/KI0 P10_3/AN3 P10_2/AN2 P10_1/AN1 AVSS P10_0/AN0 VREF AVCC P9_7/ADTRG/SIN4
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
VCC2 ports
M16C/64A Group
PRQP0100JD-B (100P6F-A) (top view)
VCC1 ports
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30
P4_4/CTS7/RTS7/CS0 P4_5/CLK7/CS1 P4_6/PWM0/RXD7/SCL7/CS2 P4_7/PWM1/TXD7/SDA7/CS3 P5_0/WRL/WR P5_1/WRH/BHE P5_2/RD P5_3/BCLK P5_4/HLDA P5_5/HOLD P5_6/ALE P5_7/RDY/CLKOUT P6_0/RTCOUT/CTS0/RTS0 P6_1/CLK0 P6_2/RXD0/SCL0 P6_3/TXD0/SDA0 P6_4/CTS1/RTS1/CTS0/CLKS1 P6_5/CLK1 P6_6/RXD1/SCL1 P6_7/TXD1/SDA1
Notes: 1. N-channel open drain output. 2. Check the position of Pin 1 by referring to appendix 1, Package Dimensions. 3. Pin names in brackets [ ] represent a single functional signal. They should not be considered as two separate functional signals.
Figure 1.4
P9_6/ANEX1/SOUT4 P9_5/ANEX0/CLK4 P9_4/DA1/TB4IN/PWM1 P9_3/DA0/TB3IN/PWM0 P9_2/TB2IN/PMC0/SOUT3 P9_1/TB1IN/PMC1/SIN3 P9_0/TB0IN/CLK3 BYTE CNVSS P8_7/XCIN P8_6/XCOUT RESET XOUT VSS XIN VCC1 P8_5/NMI/SD/CEC (1) P8_4/INT2/ZP P8_3/INT1 P8_2/INT0 P8_1/TA4IN/U/CTS5/RTS5 P8_0/TA4OUT/U/RXD5/SCL5 P7_7/TA3IN/CLK5 P7_6/TA3OUT/TXD5/SDA5 P7_5/TA2IN/W P7_4/TA2OUT/W P7_3/CTS2/RTS2/TA1IN/V P7_2/CLK2/TA1OUT/V P7_1/RXD2/SCL2/SCLMM/TA0IN/TB5IN (1) P7_0/TXD2/SDA2/SDAMM/TA0OUT (1)
M16C/64A Group
1. Overview
(See Note 3) P1_3/TXD6/SDA6/D11 P1_4/D12 P1_5/INT3/IDV/D13 P1_6/INT4/IDW/D14 P1_7/INT5/IDU/D15 P2_0/AN2_0/A0, [A0/D0], A0 P2_1/AN2_1/A1, [A1/D1], [A1/D0] P2_2/AN2_2/A2, [A2/D2], [A2/D1] P2_3/AN2_3/A3, [A3/D3], [A3/D2] P2_4/INT6/AN2_4/A4, [A4/D4], [A4/D3] P2_5/INT7/AN2_5/A5, [A5/D5], [A5/D4] P2_6/AN2_6/A6, [A6/D6], [A6/D5] P2_7/AN2_7/A7, [A7/D7], [A7/D6] VSS P3_0/A8 [A8/D7] VCC2 P3_1/A9 P3_2/A10 P3_3/A11 P3_4/A12 P3_5/A13 P3_6/A14 P3_7/A15 P4_0/A16 P4_1/A17 P1_2/RXD6/SCL6/D10 P1_1/CLK6/D9 P1_0/CTS6/RTS6/D8 P0_7/AN0_7/D7 P0_6/AN0_6/D6 P0_5/AN0_5/D5 P0_4/AN0_4/D4 P0_3/AN0_3/D3 P0_2/AN0_2/D2 P0_1/AN0_1/D1 P0_0/AN0_0/D0 P10_7/AN7/KI3 P10_6/AN6/KI2 P10_5/AN5/KI1 P10_4/AN4/KI0 P10_3/AN3 P10_2/AN2 P10_1/AN1 AVSS P10_0/AN0 VREF AVCC P9_7/ADTRG/SIN4 P9_6/ANEX1/SOUT4 P9_5/ANEX0/CLK4 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26
VCC2 ports
M16C/64A Group
PLQP0100KB-A (100P6Q-A) (top view)
VCC1 ports
P4_2/A18 P4_3/A19 P4_4/CTS7/RTS7/CS0 P4_5/CLK7/CS1 P4_6/PWM0/RXD7/SCL7/CS2 P4_7/PWM1/TXD7/SDA7/CS3 P5_0/WRL/WR P5_1/WRH/BHE P5_2/RD P5_3/BCLK P5_4/HLDA P5_5/HOLD P5_6/ALE P5_7/RDY/CLKOUT P6_0/RTCOUT/CTS0/RTS0 P6_1/CLK0 P6_2/RXD0/SCL0 P6_3/TXD0/SDA0 P6_4/CTS1/RTS1/CTS0/CLKS1 P6_5/CLK1 P6_6/RXD1/SCL1 P6_7/TXD1/SDA1 P7_0/TXD2/SDA2/SDAMM/TA0OUT (1) P7_1/RXD2/SCL2/SCLMM/TA0IN/TB5IN (1) P7_2/CLK2/TA1OUT/V
Notes: 1. N-channel open drain output. 2. Check the position of Pin 1 by referring to appendix 1, Package Dimensions. 3. Pin names in brackets [ ] represent a single functional signal. They should not be considered as two separate functional signals.
Figure 1.5
RESET XOUT VSS XIN VCC1 P8_5/NMI/SD/CEC (1) P8_4/INT2/ZP P8_3/INT1 P8_2/INT0 P8_1/TA4IN/U/CTS5/RTS5 P8_0/TA4OUT/U/RXD5/SCL5 P7_7/TA3IN/CLK5 P7_6/TA3OUT/TXD5/SDA5 P7_5/TA2IN/W P7_4/TA2OUT/W P7_3/CTS2/RTS2/TA1IN/V
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
M16C/64A Group
1. Overview
Table 1.4
Pin No. FA 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 FB 99 100 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48
P8_7 P8_6
P8_5 P8_4 P8_3 P8_2 P8_1 P8_0 P7_7 P7_6 P7_5 P7_4 P7_3 P7_2 P7_1 P7_0 P6_7 P6_6 P6_5 P6_4 P6_3 P6_2 P6_1 P6_0 P5_7 P5_6 P5_5 P5_4 P5_3 P5_2 P5_1 P5_0 P4_7 P4_6 P4_5 P4_4
SD ZP
CEC
TA4IN/U TA4OUT/U TA3IN TA3OUT TA2IN/W TA2OUT/W TA1IN/V TA1OUT/V TA0IN/TB5IN TA0OUT
RTCOUT
CTS2/RTS2 CLK2 RXD2/SCL2/SCLMM TXD2/SDA2/SDAMM TXD1/SDA1 RXD1/SCL1 CLK1 CTS1/RTS1/CTS0/ CLKS1 TXD0/SDA0 RXD0/SCL0 CLK0 CTS0/RTS0 RDY ALE HOLD HLDA BCLK RD WRH/BHE WRL/WR CS3 CS2 CS1 CS0
CLKOUT
PWM1 PWM0
M16C/64A Group
1. Overview
Table 1.5
Pin No. FA 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 FB 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98
INT7 INT6
M16C/64A Group
1. Overview
1.6
Pin Functions
Pin Functions for the 100-Pin Package (1/3)
Pin Name VCC1, VCC2, VSS AVCC, AVSS RESET I/O I Power Supply Description Apply 2.7 to 5.5 V to pins VCC1 and VCC2 (VCC1 VCC2) and 0 V to the VSS pin. This is the power supply for the A/D and D/A converters. Connect the AVCC pin to VCC1, and connect the AVSS pin to VSS. Driving this pin low resets the MCU. Input pin to switch processor modes. After a reset, to start operating in single-chip mode, connect the CNVSS pin to VSS via a resistor. To start operating in microprocessor mode, connect the pin to VCC1. Input pin to select the data bus of the external area. The data bus is 16 bits when it is low, and 8 bits when it is high. This pin must be fixed either high or low. Connect the BYTE pin to VSS in single-chip mode. Inputs or outputs data (D0 to D7) while accessing an external area with a separate bus. Inputs or outputs data (D8 to D15) while accessing an external area with a 16-bit separate bus. Outputs address bits A0 to A19. Inputs or outputs data (D0 to D7) and outputs address bits (A0 to A7) by timesharing, while accessing an external area with an 8-bit multiplexed bus. Inputs or outputs data (D0 to D7) and outputs address bits (A1 to A8) by timesharing, while accessing an external area with a 16-bit multiplexed bus. Outputs chip-select signals CS0 to CS3 to specify an external area. Outputs WRL, WRH, (WR, BHE), and RD signals. WRL and WRH can be switched with BHE and WR. WRL, WRH, and RD selected If the external data bus is 16 bits, data is written to an even address in an external area when WRL is driven low. Data is written to an odd address when WRH is driven low. Data is read when RD is driven low. WR, BHE, and RD selected Data is written to an external area when WR is driven low. Data in an external area is read when RD is driven low. An odd address is accessed when BHE is driven low. Select WR, BHE, and RD when using an 8-bit external data bus. Outputs ALE signal to latch address. The MCU is placed in a hold state while the HOLD pin is driven low. In a hold state, HLDA outputs a low-level signal. The MCU bus is placed in a wait state while the RDY pin is driven low.
Table 1.6
Power supply input Analog power supply input Reset input
Signal Name
I I
VCC1 VCC1
CNVSS
CNVSS
VCC1
BYTE
VCC1
I/O
VCC2
VCC2
VCC2
O I O I
Power supply: VCC2 is used to supply power to the external bus associated pins. The dual power supply configuration allows VCC2 to interface at a different voltage than VCC1.
M16C/64A Group
1. Overview
Table 1.7
Signal Name Main clock input Main clock output Sub clock input Sub clock output BCLK output Clock output INT interrupt input NMI interrupt input Key input interrupt input
Timer A
TA0IN to TA4IN ZP TB0IN to TB5IN U, U, V, V, W, W SD IDU, IDV, IDW RTCOUT PWM0, PWM1 PMC0, PMC1 CTS0 to CTS2, CTS5 CTS6, CTS7 RTS0 to RTS2, RTS5 RTS6, RTS7 CLK0 to CLK2, CLK5 CLK6, CLK7 RXD0 to RXD2, RXD5 RXD6, RXD7 TXD0 to TXD2, TXD5 TXD6, TXD7 CLKS1
Timer B Three-phase motor control timer Real-time clock output PWM output Remote control signal receiver input
VCC1, PWM output. VCC2 VCC1 VCC1 VCC2 VCC1 VCC2 VCC1 VCC2 VCC1 VCC2 VCC1 VCC2 VCC1 Output for the transmit/receive clock multiple-pin output function. Serial data output. (2) Serial data input. Transmit/receive clock I/O. Output pins to control data reception. Input for the remote control signal receiver.
Notes: 1. Contact the oscillator manufacturer regarding the oscillation characteristics. 2. TXD2, SDA2, and SCL2 are N-channel open drain output pins. TXDi (i = 0, 1, 5 to 7), SDAi, and SCLi can be selected as CMOS output pins or N-channel open drain output pins.
M16C/64A Group
1. Overview
Table 1.8
Signal Name
UART0 to UART2, UART5 to UART7 I2C mode Serial interface SI/O3, SI/O4 Multi-master I2C-bus interface CEC I/O Reference voltage input
A/D converter
D/A converter
DA0, DA1 P0_0 to P0_7 P1_0 to P1_7 P2_0 to P2_7 P3_0 to P3_7 P4_0 to P4_7 P5_0 to P5_7 P6_0 to P6_7 P7_0 to P7_7 P8_0 to P8_7 P9_0 to P9_7 P10_0 to P10_7
I/O
VCC2
8-bit CMOS I/O ports. A direction register determines whether each pin is used as an input port or an output port. A pull-up resistor may be enabled or disabled for input ports in 4-bit units.
I/O ports
I/O
VCC1
8-bit I/O ports having equivalent functions to P0. However, P7_0, P7_1, and P8_5 are N-channel open drain output ports. No pull-up resistor is provided. P8_5 is an input port for verifying the NMI pin level and shares a pin with NMI.
M16C/64A Group
2.
Figure 2.1 shows the CPU registers. Seven registers (R0, R1, R2, R3, A0, A1, and FB) out of 13 compose a register bank, and there are two register banks.
b31
b15
b8 b7
b0
R2 R3
R0H(high-order bits of R0) R0L (low-order bits of R0) R1H(high-order bits of R1) R1L (low-order bits of R1)
b19
b15
INTBH
INTBL
INTBH is the 4 high-order bits of the INTB register and INTBL is the 16 low-order bits.
b19 b0
PC
b15 b0
Program counter
USP ISP SB
b15 b0
FLG
b15 b8 b7 b0
Flag register
IPL
U I
O B S Z D C
Carry flag Debug flag Zero flag Sign flag Register bank select flag Overflow flag Interrupt enable flag Stack pointer select flag Reserved area Processor interrupt priority level Reserved area
Note: 1. These registers compose a register bank. There are two register banks.
Figure 2.1
CPU Register
2.1
R0, R1, R2, and R3 are 16-bit registers used for transfer, arithmetic, and logic operations. R0 and R1 can be split into high-order (R0H/R1H) and low-order (R0L/R1L) bits to be used separately as 8-bit data registers. R0 can be combined with R2, and R3 can be combined with R1 and be used as 32-bit data registers R2R0 and R3R1, respectively.
M16C/64A Group
2.2
A0 and A1 are 16-bit registers used for indirect addressing, relative addressing, transfer, arithmetic, and logic operations. A0 can be combined with A1 and used as a 32-bit address register (A1A0).
2.3
2.4
INTB is a 20-bit register that indicates the start address of a relocatable interrupt vector table.
2.5
The PC is 20 bits wide and indicates the address of the next instruction to be executed.
2.6
The USP and ISP stack pointers (SP) are each comprised of 16 bits. The U flag is used to switch between USP and ISP.
2.7
2.8
2.8.1
The C flag retains a carry, borrow, or shift-out bit generated by the arithmetic/logic unit.
2.8.2
2.8.3
2.8.4
The S flag becomes 1 when an arithmetic operation results in a negative value. Otherwise, it becomes 0.
2.8.5
Register bank 0 is selected when the B flag is 0. Register bank 1 is selected when this flag is 1.
2.8.6
The O flag becomes 1 when an arithmetic operation results in an overflow. Otherwise, it becomes 0.
2.8.7
The I flag enables maskable interrupts. Maskable interrupts are disabled when the I flag is 0, and enabled when it is 1. The I flag becomes 0 when an interrupt request is accepted.
M16C/64A Group
2.8.8
ISP is selected when the U flag is 0. USP is selected when the U flag is 1. The U flag becomes 0 when a hardware interrupt request is accepted, or the INT instruction of software interrupt number 0 to 31 is executed.
2.8.9
IPL is 3 bits wide and assigns processor interrupt priority levels from 0 to 7. If a requested interrupt has higher priority than IPL, the interrupt request is enabled.
2.8.10
Reserved Areas
M16C/64A Group
3. Address Space
3.
3.1
Address Space
Address Space
The M16C/64A Group has a 1 MB address space from 00000h to FFFFFh. Address space is expandable to 4 MB with the memory area expansion function. Addresses 40000h to BFFFFh can be used as external areas from bank 0 to bank 7. Figure 3.1 shows the Address Space. Areas that can be accessed vary depending on processor mode and the status of each control bit.
Memory expansion mode 00000h 00400h Internal RAM Reserved area 04000h 0D000h 0D800h 0E000h 10000h 1 MB address space 14000h External area 27000h Reserved area 28000h 40000h External area Bank 0 BFFFFh D0000h Reserved area Internal ROM (program ROM 1) FFFFFh Notes: 1. Do not access reserved areas. 2. The figure above applies under the following conditions: - The PM13 bit in the PM1 register 0 (addresses 04000h to 0CFFFh and 80000h to CFFFFh are used as external areas) Program ROM1 is allocated from address FFFFFh lower. 512 KB 8 External area SFR External area Internal ROM (data flash) Internal ROM (program ROM 2) In 4-MB mode When data flash is enabled When program ROM 2 is enabled Bank 7 Bank 6 Bank 5 Bank 4 Bank 3 Bank 2 Bank 1 SFR The internal RAM is allocated from address 00400h higher.
Figure 3.1
Address Space
M16C/64A Group
3. Address Space
3.2
Memory Map
Special function registers (SFRs) are allocated from address 00000h to 003FFh and from 0D000h to 0D7FFh. Peripheral function control registers are located here. All blank areas within SFRs are reserved. Do not access these areas. Internal RAM is allocated from address 00400h higher, with 10 KB of internal RAM allocated from 00400h to 02BFFh. Internal RAM is used not only for data storage, but also for the stack area when subroutines are called or when an interrupt request is accepted. The internal ROM is flash memory. Three internal ROM areas are available: data flash, program ROM 1, and program ROM 2. The data flash is allocated from 0E000h to 0FFFFh. This data flash area is mostly used for data storage, but can also store programs. Program ROM 2 is allocated from 10000h to 13FFFh. Program ROM 1 is allocated from FFFFFh lower, with the 64-KB program ROM 1 area allocated from address F0000h to FFFFFh. The special page vectors are allocated from FFE00h to FFFD7h. They are used for the JMPS and JSRS instructions. Refer to the M16C/60, M16C/20, M16C/Tiny Series Software Manual for details. The fixed vector table for interrupts is allocated from FFFDCh to FFFFFh. The 256 bytes beginning with the start address set in the INTB register compose the relocatable vector table for interrupts. Figure 3.2 shows the Memory Map.
00400h XXXXXh Reserved area 0D000h 0D800h 0E000h 10000h 14000h External area 27000h 28000h
Relocatable vector table
SFR External area Internal ROM (data flash) Internal ROM (program ROM 2) 13800h 13FF0h 13FFFh On-chip debugger monitor area User boot code area
Reserved area
External area Program ROM 1 Address YYYYYh Size 128 KB 256 KB 512 KB E0000h C0000h 80000h YYYYYh Internal ROM (program ROM 1) FFFFFh 80000h Reserved area FFE00h
256 bytes beginning with the start address set in the INTB register
FFFD8h FFFDCh
FFFFFh
OFS1 address
Notes: 1. Do not access reserved areas. 2. The figure above applies under the following conditions: - Memory expansion mode - The PM10 bit in the PM1 register is 1 (addresses 0E000h to 0FFFFh are used as data flash) - The PRG2C0 bit in the PRG2C register is 0 (program ROM 2 enabled) - The PM13 bit in the PM1 register is 1 (all areas in internal RAM, and the program ROM 1 area from 80000h are usable)
Figure 3.2
Memory Map
M16C/64A Group
3. Address Space
3.3
Areas that can be accessed vary depending on processor mode and the status of each control bit. Figure 3.3 shows the Accessible Area in Each Mode. In single-chip mode, the SFRs, internal RAM, and internal ROM can be accessed. In memory expansion mode, the SFRs, internal RAM, internal ROM, and external areas can be accessed. Address space is expandable to 4 MB with the memory area expansion function. In microprocessor mode, the SFRs, internal RAM, and external areas can be accessed. Address space is expandable to 4 MB with the memory area expansion function. Allocate ROM to the fixed vector table from FFFDCh to FFFFFh.
Single-Chip Mode 00000h 00400h Internal RAM Reserved area 0D000h 0D800h 0E000h 10000h 14000h SFR Reserved area Internal ROM (data flash) Internal ROM (program ROM 2) SFR
Memory Expansion Mode 00000h SFR 00400h Internal RAM Reserved area 0D000h 0D800h 0E000h 10000h 14000h External area 27000h Reserved area 28000h SFR External area Internal ROM (data flash) Internal ROM (program ROM 2)
Microprocessor Mode 00000h 00400h Internal RAM Reserved area 0D000h 0D800h SFR SFR
External area
Reserved area
Notes: 1. Do not access reserved areas. 2. The figure above applies under the following conditions: Single-chip mode and memory expansion mode - The PM10 bit in the PM1 register is 1 (addresses f0E000h to 0FFFFh are used as data flash) - The PRG2C0 bit in the PRG2C register is 0 (program ROM 2 enabled) - The PM13 bit in the PM1 register is 1 (all areas in internal RAM, and the program ROM 1 area from 80000h are usable) Microprocessor mode - The PM10 bit is 0 (addresses 0E000h to 0FFFFh are used as the CS2 area) - The PRG2C0 bit is 1 (program ROM 2 disabled)
Figure 3.3
M16C/64A Group
4.
4.1
An SFR is a control register for a peripheral function. Table 4.1 to Table 4.15 list SFR information.
Table 4.1
Address
0000h 0001h 0002h 0003h 0004h 0005h 0006h 0007h 0008h 0009h 000Ah 000Bh 000Ch 000Dh 000Eh 000Fh 0010h 0011h 0012h 0013h 0014h 0015h 0016h 0017h 0018h 0019h 001Ah 001Bh 001Ch 001Dh 001Eh 001Fh Notes: 1. 2. 3. 4. 5. 6. Processor Mode Register 0 Processor Mode Register 1 System Clock Control Register 0 System Clock Control Register 1 Chip Select Control Register Protect Register Data Bank Register Oscillation Stop Detection Register PM0 PM1 CM0 CM1 CSR PRCR DBR CM2 0000 0000b (CNVSS pin is low) 0000 0011b (CNVSS pin is high) (2) 0000 1000b 0100 1000b 0010 0000b 01h 00h 00h 0X00 0010b (3)
PRG2C PCLKR
CPSRF
0XXX XXXXb
Reset Source Determine Register Voltage Detector 2 Flag Register Voltage Detector Operation Enable Register Chip Select Expansion Control Register PLL Control Register 0 Processor Mode Register 2
XX00 001Xb (hardware reset) (4) 0000 X000b (2) 000X 0000b (2, 5) 001X 0000b (2, 6) 00h 0X01 X010b XX00 0X01b
X: Undefined The blank areas are reserved. No access is allowed. Software reset, watchdog timer reset, oscillator stop detect reset, voltage monitor 1 reset, and voltage monitor 2 reset do not affect the following bits and registers: The VCR1 register, the VCR2 register, and bits PM01 and PM00 in the PM0 register. Oscillator stop detect reset does not affect bits CM20, CM21, and CM27. The state of bits in the RSTFR register depends on the reset type. This is the reset value when the LVDAS bit of address OFS1 is 1 during hardware reset. This is the reset value after voltage monitor 0 reset, power-on reset, and when the LVDAS bit of address OFS1 is 0 during hardware reset.
M16C/64A Group
Table 4.2
Address
0020h 0021h 0022h 0023h 0024h 0025h 0026h 0027h 0028h 0029h 002Ah 002Bh 002Ch 002Dh 002Eh 002Fh 0030h 0031h 0032h 0033h 0034h 0035h 0036h 0037h 0038h 0039h 003Ah 003Bh 003Ch 003Dh 003Eh 003Fh 0040h 0041h 0042h 0043h 0044h 0045h 0046h 0047h 0048h 0049h 004Ah 004Bh 004Ch 004Dh 004Eh 004Fh Notes: 1. 2. 3. 4. 5. 6.
Voltage Monitor Function Select Register Voltage Detector 1 Level Select Register
VWCE VD1LS
00h (5) 0000 1010b (5) 1100 XX10b (2, 3) 1100 XX11b (2, 4) 1000 XX10b (6) 1000 0X10b (6)
Voltage Monitor 0 Control Register Voltage Monitor 1 Control Register Voltage Monitor 2 Control Register
INT7 Interrupt Control Register INT6 Interrupt Control Register INT3 Interrupt Control Register Timer B5 Interrupt Control Register Timer B4 Interrupt Control Register UART1 Bus Collision Detection Interrupt Control Register Timer B3 Interrupt Control Register UART0 Bus Collision Detection Interrupt Control Register SI/O4 Interrupt Control Register INT5 Interrupt Control Register SI/O3 Interrupt Control Register INT4 Interrupt Control Register UART2 Bus Collision Detection Interrupt Control Register DMA0 Interrupt Control Register DMA1 Interrupt Control Register Key Input Interrupt Control Register A/D Conversion Interrupt Control Register UART2 Transmit Interrupt Control Register
INT7IC INT6IC INT3IC TB5IC TB4IC U1BCNIC TB3IC U0BCNIC S4IC INT5IC S3IC INT4IC BCNIC DM0IC DM1IC KUPIC ADIC S2TIC
XX00 X000b XX00 X000b XX00 X000b XXXX X000b XXXX X000b XXXX X000b XX00 X000b XX00 X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b
X: Undefined The blank areas are reserved. No access is allowed. Software reset, watchdog timer reset, oscillator stop detect reset, voltage monitor 1 reset, and voltage monitor 2 reset do not affect the following registers or bit: the VW0C register, and the VW2C3 bit in the VW2C register. This is the reset value when the LVDAS bit of address OFS1 is 1 during hardware reset This is the reset value after voltage monitor 0 reset, power-on reset, and when the LVDAS bit of address OFS1 is 0 during hardware reset. Hardware reset, power-on reset, voltage monitor 0 reset, voltage monitor 1 reset, or voltage monitor 2 reset Hardware reset, power-on reset, or voltage monitor 0 reset
M16C/64A Group
Table 4.3
Address
0050h 0051h 0052h 0053h 0054h 0055h 0056h 0057h 0058h 0059h 005Ah 005Bh 005Ch 005Dh 005Eh 005Fh 0060h 0061h 0062h 0063h 0064h 0065h 0066h 0067h 0068h 0069h 006Ah 006Bh 006Ch 006Dh 006Eh 006Fh 0070h 0071h 0072h
Symbol
S2RIC S0TIC S0RIC S1TIC S1RIC TA0IC TA1IC TA2IC TA3IC TA4IC TB0IC TB1IC TB2IC INT0IC INT1IC INT2IC
Reset Value
XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XX00 X000b XX00 X000b XX00 X000b
0073h 0074h 0075h 0076h 0077h 0078h 0079h 007Ah 007Bh I2C-bus Interface Interrupt Control Register 007Ch SCL/SDA Interrupt Control Register 007Dh 007Eh 007Fh 0080h to 017Fh Note: 1. The blank areas are reserved. No access is allowed.
DMA2 Interrupt Control Register DMA3 Interrupt Control Register UART5 Bus Collision Detection Interrupt Control Register CEC1 Interrupt Control Register UART5 Transmit Interrupt Control Register CEC2 Interrupt Control Register UART5 Receive Interrupt Control Register UART6 Bus Collision Detection Interrupt Control Register Real-Time Clock Periodic Interrupt Control Register UART6 Transmit Interrupt Control Register Real-Time Clock Compare Interrupt Control Register UART6 Receive Interrupt Control Register UART7 Bus Collision Detection Interrupt Control Register Remote Control Signal Receiver 0 Interrupt Control Register UART7 Transmit Interrupt Control Register Remote Control Signal Receiver 1 Interrupt Control Register UART7 Receive Interrupt Control Register
DM2IC DM3IC U5BCNIC CEC1IC S5TIC CEC2IC S5RIC U6BCNIC RTCTIC S6TIC RTCCIC S6RIC U7BCNIC PMC0IC S7TIC PMC1IC S7RIC
XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b XXXX X000b
IICIC SCLDAIC
X: Undefined
M16C/64A Group
Table 4.4
Address
0180h 0181h 0182h 0183h 0184h 0185h 0186h 0187h 0188h 0189h 018Ah 018Bh 018Ch 018Dh 018Eh 018Fh 0190h 0191h 0192h 0193h 0194h 0195h 0196h 0197h 0198h 0199h 019Ah 019Bh 019Ch 019Dh 019Eh 019Fh 01A0h 01A1h 01A2h 01A3h 01A4h 01A5h 01A6h 01A7h 01A8h 01A9h 01AAh 01ABh 01ACh 01ADh 01AEh 01AFh Note: 1.
Symbol
SAR0
Reset Value
XXh XXh 0Xh XXh XXh 0Xh XXh XXh
DAR0
TCR0
DM0CON
0000 0X00b
SAR1
DAR1
TCR1
DM1CON
0000 0X00b
SAR2
DAR2
TCR2
DM2CON
0000 0X00b
M16C/64A Group
Table 4.5
Address
01B0h 01B1h 01B2h 01B3h 01B4h 01B5h 01B6h 01B7h 01B8h 01B9h 01BAh 01BBh 01BCh 01BDh 01BEh 01BFh 01C0h 01C1h 01C2h 01C3h 01C4h 01C5h 01C6h 01C7h 01C8h 01C9h 01CAh 01CBh 01CCh 01CDh 01CEh 01CFh 01D0h 01D1h 01D2h 01D3h 01D4h 01D5h 01D6h 01D7h 01D8h 01D9h 01DAh 01DBh 01DCh 01DDh 01DEh 01DFh Note: 1.
Symbol
SAR3
Reset Value
XXh XXh 0Xh XXh XXh 0Xh XXh XXh
DAR3
TCR3
DM3CON
0000 0X00b
Timer B0-1 Register Timer B1-1 Register Timer B2-1 Register Pulse Period/Pulse Width Measurement Mode Function Select Register 1 Timer B Count Source Select Register 0 Timer B Count Source Select Register 1
XXh XXh XXh XXh XXh XXh XXXX X000b 00h X0h
Timer A Count Source Select Register 0 Timer A Count Source Select Register 1 Timer A Count Source Select Register 2 16-Bit Pulse Width Modulation Mode Function Select Register Timer A Waveform Output Function Select Register
Timer A Output Waveform Change Enable Register Three-Phase Protect Control Register
TAOW TPRC
M16C/64A Group
Table 4.6
Address
01E0h 01E1h 01E2h 01E3h 01E4h 01E5h 01E6h 01E7h 01E8h 01E9h 01EAh 01EBh 01ECh 01EDh 01EEh 01EFh 01F0h 01F1h 01F2h 01F3h 01F4h 01F5h 01F6h 01F7h 01F8h 01F9h 01FAh 01FBh 01FCh 01FDh 01FEh 01FFh 0200h 0201h 0202h 0203h 0204h 0205h 0206h 0207h 0208h 0209h 020Ah 020Bh 020Ch 020Dh 020Eh 020Fh Note: 1.
Symbol
TB31 TB41 TB51 PPWFS2 TBCS2 TBCS3
Reset Value
XXh XXh XXh XXh XXh XXh XXXX X000b 00h X0h
PMC0 Function Select Register 0 PMC0 Function Select Register 1 PMC0 Function Select Register 2 PMC0 Function Select Register 3 PMC0 Status Register PMC0 Interrupt Source Select Register PMC0 Compare Control Register PMC0 Compare Data Register PMC1 Function Select Register 0 PMC1 Function Select Register 1 PMC1 Function Select Register 2 PMC1 Function Select Register 3 PMC1 Status Register PMC1 Interrupt Source Select Register
PMC0CON0 PMC0CON1 PMC0CON2 PMC0CON3 PMC0STS PMC0INT PMC0CPC PMC0CPD PMC1CON0 PMC1CON1 PMC1CON2 PMC1CON3 PMC1STS PMC1INT
00h 00XX 0000b 0000 00X0b 00h 00h 00h XXX0 X000b 00h XXX0 X000b XXXX 0X00b 0000 00X0b 00h X000 X00Xb X000 X00Xb
Interrupt Source Select Register 3 Interrupt Source Select Register 2 Interrupt Source Select Register
Address Match Interrupt Enable Register Address Match Interrupt Enable Register 2
AIER AIER2
M16C/64A Group
Table 4.7
Address
0210h 0211h 0212h 0213h 0214h 0215h 0216h 0217h 0218h 0219h 021Ah 021Bh 021Ch 021Dh 021Eh 021Fh 0220h 0221h 0222h 0223h 0224h 0225h 0226h 0227h 0228h 0229h 022Ah 022Bh 022Ch 022Dh 022Eh 022Fh 0230h 0231h 0232h 0233h 0234h 0235h 0236h 0237h 0238h 0239h 023Ah 023Bh 023Ch 023Dh 023Eh 023Fh Note: 1.
Symbol
RMAD0
Reset Value
00h 00h X0h 00h 00h X0h 00h 00h X0h 00h 00h X0h 0000 0001b (Other than user boot mode) 0010 0001b (User boot mode) 00X0 XX0Xb XXXX 0000b
RMAD1
RMAD2
RMAD3
Flash Memory Control Register 0 Flash Memory Control Register 1 Flash Memory Control Register 2
M16C/64A Group
Table 4.8
Address
0240h 0241h 0242h 0243h 0244h 0245h 0246h 0247h 0248h 0249h 024Ah 024Bh 024Ch 024Dh 024Eh 024Fh 0250h 0251h 0252h 0253h 0254h 0255h 0256h 0257h 0258h 0259h 025Ah 025Bh 025Ch 025Dh 025Eh 025Fh 0260h 0261h 0262h 0263h 0264h 0265h 0266h 0267h 0268h 0269h 026Ah 026Bh 026Ch 026Dh 026Eh 026Fh Note: 1.
UART0 Special Mode Register 4 UART0 Special Mode Register 3 UART0 Special Mode Register 2 UART0 Special Mode Register UART0 Transmit/Receive Mode Register UART0 Bit Rate Register UART0 Transmit Buffer Register UART0 Transmit/Receive Control Register 0 UART0 Transmit/Receive Control Register 1 UART0 Receive Buffer Register UART Transmit/Receive Control Register 2
U0SMR4 U0SMR3 U0SMR2 U0SMR U0MR U0BRG U0TB U0C0 U0C1 U0RB UCON
00h 000X 0X0Xb X000 0000b X000 0000b 00h XXh XXh XXh 0000 1000b 00XX 0010b XXh XXh X000 0000b
UART1 Special Mode Register 4 UART1 Special Mode Register 3 UART1 Special Mode Register 2 UART1 Special Mode Register UART1 Transmit/Receive Mode Register UART1 Bit Rate Register UART1 Transmit Buffer Register UART1 Transmit/Receive Control Register 0 UART1 Transmit/Receive Control Register 1 UART1 Receive Buffer Register
U1SMR4 U1SMR3 U1SMR2 U1SMR U1MR U1BRG U1TB U1C0 U1C1 U1RB
00h 000X 0X0Xb X000 0000b X000 0000b 00h XXh XXh XXh 0000 1000b 00XX 0010b XXh XXh
UART2 Special Mode Register 4 UART2 Special Mode Register 3 UART2 Special Mode Register 2 UART2 Special Mode Register UART2 Transmit/Receive Mode Register UART2 Bit Rate Register UART2 Transmit Buffer Register UART2 Transmit/Receive Control Register 0 UART2 Transmit/Receive Control Register 1 UART2 Receive Buffer Register
U2SMR4 U2SMR3 U2SMR2 U2SMR U2MR U2BRG U2TB U2C0 U2C1 U2RB
00h 000X 0X0Xb X000 0000b X000 0000b 00h XXh XXh XXh 0000 1000b 0000 0010b XXh XXh X: Undefined
M16C/64A Group
Table 4.9
Address
0270h 0271h 0272h 0273h 0274h 0275h 0276h 0277h 0278h 0279h 027Ah 027Bh 027Ch 027Dh 027Eh 027Fh 0280h 0281h 0282h 0283h 0284h 0285h 0286h 0287h 0288h 0289h 028Ah 028Bh 028Ch 028Dh 028Eh 028Fh 0290h 0291h 0292h 0293h 0294h 0295h 0296h 0297h 0298h 0299h 029Ah 029Bh 029Ch 029Dh 029Eh 029Fh Note: 1.
Symbol
S3TRR S3C S3BRG S4TRR S4C S4BRG S34C2
Reset Value
XXh 0100 0000b XXh XXh 0100 0000b XXh 00XX X0X0b
UART5 Special Mode Register 4 UART5 Special Mode Register 3 UART5 Special Mode Register 2 UART5 Special Mode Register UART5 Transmit/Receive Mode Register UART5 Bit Rate Register UART5 Transmit Buffer Register UART5 Transmit/Receive Control Register 0 UART5 Transmit/Receive Control Register 1 UART5 Receive Buffer Register
U5SMR4 U5SMR3 U5SMR2 U5SMR U5MR U5BRG U5TB U5C0 U5C1 U5RB
00h 000X 0X0Xb X000 0000b X000 0000b 00h XXh XXh XXh 0000 1000b 0000 0010b XXh XXh
UART6 Special Mode Register 4 UART6 Special Mode Register 3 UART6 Special Mode Register 2 UART6 Special Mode Register UART6 Transmit/Receive Mode Register UART6 Bit Rate Register UART6 Transmit Buffer Register UART6 Transmit/Receive Control Register 0 UART6 Transmit/Receive Control Register 1 UART6 Receive Buffer Register
U6SMR4 U6SMR3 U6SMR2 U6SMR U6MR U6BRG U6TB U6C0 U6C1 U6RB
00h 000X 0X0Xb X000 0000b X000 0000b 00h XXh XXh XXh 0000 1000b 0000 0010b XXh XXh X: Undefined
M16C/64A Group
Table 4.10
Address
02A0h 02A1h 02A2h 02A3h 02A4h 02A5h 02A6h 02A7h 02A8h 02A9h 02AAh 02ABh 02ACh 02ADh 02AEh 02AFh 02B0h 02B1h 02B2h 02B3h 02B4h 02B5h 02B6h 02B7h 02B8h 02B9h 02BAh 02BBh 02BCh 02BDh 02BEh 02BFh 02C0h to 02FFh 0300h 0301h 0302h 0303h 0304h 0305h 0306h 0307h 0308h 0309h 030Ah 030Bh 030Ch 030Dh 030Eh 030Fh Note: 1.
UART7 Special Mode Register 4 UART7 Special Mode Register 3 UART7 Special Mode Register 2 UART7 Special Mode Register UART7 Transmit/Receive Mode Register UART7 Bit Rate Register UART7 Transmit Buffer Register UART7 Transmit/Receive Control Register 0 UART7 Transmit/Receive Control Register 1 UART7 Receive Buffer Register I2C0 Data Shift Register I2C0 Address Register 0 I2C0 Control Register I2C0 Clock Control Register I2C0 Start/Stop Condition Control Register I2C0 Control Register 1 I2C0 Control Register 2 I2C0 Status Register 0 I2C0 Status Register 1 I2C0 Address Register 1 I2C0 Address Register 2
U7SMR4 U7SMR3 U7SMR2 U7SMR U7MR U7BRG U7TB U7C0 U7C1 U7RB S00 S0D0 S1D0 S20 S2D0 S3D0 S4D0 S10 S11 S0D1 S0D2
00h 000X 0X0Xb X000 0000b X000 0000b 00h XXh XXh XXh 0000 1000b 0000 0010b XXh XXh XXh 0000 000Xb 00h 00h 0001 1010b 0011 0000b 00h 0001 000Xb 00h 0000 000Xb 0000 000Xb
Timer B3/B4/B5 Count Start Flag Timer A1-1 Register Timer A2-1 Register Timer A4-1 Register Three-Phase PWM Control Register 0 Three-Phase PWM Control Register 1 Three-Phase Output Buffer Register 0 Three-Phase Output Buffer Register 1 Dead Time Timer Timer B2 Interrupt Generation Frequency Set Counter Position-Data-Retain Function Control Register
TBSR TA11 TA21 TA41 INVC0 INVC1 IDB0 IDB1 DTT ICTB2 PDRF
000X XXXXb XXh XXh XXh XXh XXh XXh 00h 00h XX11 1111b XX11 1111b XXh XXh XXXX 0000b
M16C/64A Group
Table 4.11
Address
0310h 0311h 0312h 0313h 0314h 0315h 0316h 0317h 0318h 0319h 031Ah 031Bh 031Ch 031Dh 031Eh 031Fh 0320h 0321h 0322h 0323h 0324h 0325h 0326h 0327h 0328h 0329h 032Ah 032Bh 032Ch 032Dh 032Eh 032Fh 0330h 0331h 0332h 0333h 0334h 0335h 0336h 0337h 0338h 0339h 033Ah 033Bh 033Ch 033Dh 033Eh 033Fh Note: 1.
Symbol
TB3 TB4 TB5
Reset Value
XXh XXh XXh XXh XXh XXh
PFCR
0011 1111b
Count Start Flag One-Shot Start Flag Trigger Select Register Up/Down Flag Timer A0 Register Timer A1 Register Timer A2 Register Timer A3 Register Timer A4 Register Timer B0 Register Timer B1 Register Timer B2 Register Timer A0 Mode Register Timer A1 Mode Register Timer A2 Mode Register Timer A3 Mode Register Timer A4 Mode Register Timer B0 Mode Register Timer B1 Mode Register Timer B2 Mode Register Timer B2 Special Mode Register
TABSR ONSF TRGSR UDF TA0 TA1 TA2 TA3 TA4 TB0 TB1 TB2 TA0MR TA1MR TA2MR TA3MR TA4MR TB0MR TB1MR TB2MR TB2SC
00h 00h 00h 00h XXh XXh XXh XXh XXh XXh XXh XXh XXh XXh XXh XXh XXh XXh XXh XXh 00h 00h 00h 00h 00h 00XX 0000b 00XX 0000b 00XX 0000b XXXX XX00b
M16C/64A Group
Table 4.12
Address
0340h 0341h 0342h 0343h 0344h 0345h 0346h 0347h 0348h 0349h 034Ah 034Bh 034Ch 034Dh 034Eh 034Fh 0350h 0351h 0352h 0353h 0354h 0355h 0356h 0357h 0358h 0359h 035Ah 035Bh 035Ch 035Dh 035Eh 035Fh 0360h 0361h 0362h 0363h 0364h 0365h 0366h 0367h 0368h 0369h 036Ah 036Bh 036Ch 036Dh 036Eh 036Fh Notes: 1. 2.
Reset Value
00h X000 0000b XX00 0000b XXXX X000b 0000 X00Xb X000 0000b XXX0 0000b X000 0000b X000 0000b X000 0000b
Real-Time Clock Second Data Register Real-Time Clock Minute Data Register Real-Time Clock Hour Data Register Real-Time Clock Day Data Register Real-Time Clock Control Register 1 Real-Time Clock Control Register 2 Real-Time Clock Count Source Select Register Real-Time Clock Second Compare Data Register Real-Time Clock Minute Compare Data Register Real-Time Clock Hour Compare Data Register
CEC Function Control Register 1 CEC Function Control Register 2 CEC Function Control Register 3 CEC Function Control Register 4 CEC Flag Register CEC Interrupt Source Select Register CEC Transmit Buffer Register 1 CEC Transmit Buffer Register 2 CEC Receive Buffer Register 1 CEC Receive Buffer Register 2 CEC Receive Follower Address Set Register 1 CEC Receive Follower Address Set Register 2
CECC1 CECC2 CECC3 CECC4 CECFLG CISEL CCTB1 CCTB2 CCRB1 CCRB2 CRADRI1 CRADRI2
XXXX X000b 00h XXXX 0000b 00h 00h 00h 00h XXXX XX00b 00h XXXX X000b 00h 00h
PCR
0000 0XX0b
NMIDF
XXXX X000b
X: Undefined The blank areas are reserved. No access is allowed. Values after hardware reset, power-on reset, or voltage monitor 0 reset are as follows: - 00000000b when a low-level signal is input to the CNVSS pin - 00000010b when a high-level signal is input to the CNVSS pin Values after voltage monitor 1 reset, voltage monitor 2 reset, software reset, watchdog timer reset, or oscillation stop detect reset are as follows: - 00000000b when bits PM01 and PM00 in the PM0 register are 00b (single-chip mode). - 00000010b when bits PM01 and PM00 in the PM0 register are 01b (memory expansion mode) or 11b (microprocessor mode).
M16C/64A Group
Table 4.13
Address
0370h 0371h 0372h 0373h 0374h 0375h 0376h 0377h 0378h 0379h 037Ah 037Bh 037Ch 037Dh 037Eh 037Fh 0380h 0381h 0382h 0383h 0384h 0385h 0386h 0387h 0388h 0389h 038Ah 038Bh 038Ch 038Dh 038Eh 038Fh 0390h 0391h 0392h 0393h 0394h 0395h 0396h 0397h 0398h 0399h 039Ah 039Bh 039Ch 039Dh 039Eh 039Fh Notes: 1. 2.
Reset Value
00h 00h 00h 00h 00h 00h
PWM Control Register 0 PWM0 Prescaler PWM0 Register PWM1 Prescaler PWM1 Register PWM Control Register 1
Count Source Protection Mode Register Watchdog Timer Reset Register Watchdog Timer Start Register Watchdog Timer Control Register
DM2SL DM3SL
00h 00h
DM0SL DM1SL
00h 00h
X: Undefined The blank areas are reserved. No access is allowed. When the CSPROINI bit in the OFS1 address is 0, the reset value is 10000000b.
M16C/64A Group
Table 4.14
Address
03A0h 03A1h 03A2h 03A3h 03A4h 03A5h 03A6h 03A7h 03A8h 03A9h 03AAh 03ABh 03ACh 03ADh 03AEh 03AFh 03B0h 03B1h 03B2h 03B3h 03B4h 03B5h 03B6h 03B7h 03B8h 03B9h 03BAh 03BBh 03BCh 03BDh 03BEh 03BFh 03C0h 03C1h 03C2h 03C3h 03C4h 03C5h 03C6h 03C7h 03C8h 03C9h 03CAh 03CBh 03CCh 03CDh 03CEh 03CFh Note: 1.
AINRST
XX00 0000b
CRCSAR CRCMR
CRCD CRCIN
XXh XXh XXh XXXX XXXXb 0000 00XXb XXXX XXXXb 0000 00XXb XXXX XXXXb 0000 00XXb XXXX XXXXb 0000 00XXb XXXX XXXXb 0000 00XXb XXXX XXXXb 0000 00XXb XXXX XXXXb 0000 00XXb XXXX XXXXb 0000 00XXb X: Undefined
A/D Register 0 A/D Register 1 A/D Register 2 A/D Register 3 A/D Register 4 A/D Register 5 A/D Register 6 A/D Register 7
M16C/64A Group
Table 4.15
Address
03D0h 03D1h 03D2h 03D3h 03D4h 03D5h 03D6h 03D7h 03D8h 03D9h 03DAh 03DBh 03DCh 03DDh 03DEh 03DFh 03E0h 03E1h 03E2h 03E3h 03E4h 03E5h 03E6h 03E7h 03E8h 03E9h 03EAh 03EBh 03ECh 03EDh 03EEh 03EFh 03F0h 03F1h 03F2h 03F3h 03F4h 03F5h 03F6h 03F7h 03F8h 03F9h 03FAh 03FBh 03FCh 03FDh 03FEh 03FFh 0400h to D07Fh Note: 1.
A/D Control Register 2 A/D Control Register 0 A/D Control Register 1 D/A0 Register D/A1 Register D/A Control Register
0000 X00Xb 0000 0XXXb 0000 X000b 00h 00h XXXX XX00b
Port P0 Register Port P1 Register Port P0 Direction Register Port P1 Direction Register Port P2 Register Port P3 Register Port P2 Direction Register Port P3 Direction Register Port P4 Register Port P5 Register Port P4 Direction Register Port P5 Direction Register Port P6 Register Port P7 Register Port P6 Direction Register Port P7 Direction Register Port P8 Register Port P9 Register Port P8 Direction Register Port P9 Direction Register Port P10 Register Port P10 Direction Register
P0 P1 PD0 PD1 P2 P3 PD2 PD3 P4 P5 PD4 PD5 P6 P7 PD6 PD7 P8 P9 PD8 PD9 P10 PD10
XXh XXh 00h 00h XXh XXh 00h 00h XXh XXh 00h 00h XXh XXh 00h 00h XXh XXh 00h 00h XXh 00h
M16C/64A Group
Table 4.16
Address
D080h D081h D082h D083h D084h D085h D086h D087h D088h D089h D08Ah D08Bh D08Ch D08Dh D08Eh D08Fh D090h D091h D092h D093h D094h D095h D096h D097h D098h D099h D09Ah D09Bh D09Ch D09Dh D09Eh D09Fh Note: 1.
Reset Value
00h XXXX X000b 00h XXXX X000b 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h 00h XX00 0000b 00h XXXX X000b 00h XXXX X000b 00h 00h 00h 00h 00h 00h 00h 00h X: Undefined
PMC0 Header Pattern Set Register (Min) PMC0 Header Pattern Set Register (Max) PMC0 Data0 Pattern Set Register (Min) PMC0 Data0 Pattern Set Register (Max) PMC0 Data1 Pattern Set Register (Min) PMC0 Data1 Pattern Set Register (Max) PMC0 Measurements Register PMC0 Counter Value Register PMC0 Receive Data Store Register 0 PMC0 Receive Data Store Register 1 PMC0 Receive Data Store Register 2 PMC0 Receive Data Store Register 3 PMC0 Receive Data Store Register 4 PMC0 Receive Data Store Register 5 PMC0 Receive Bit Count Register PMC1 Header Pattern Set Register (Min) PMC1 Header Pattern Set Register (Max) PMC1 Data0 Pattern Set Register (Min) PMC1 Data0 Pattern Set Register (Max) PMC1 Data1 Pattern Set Register (Min) PMC1 Data1 Pattern Set Register (Max) PMC1 Measurements Register PMC1 Counter Value Register
M16C/64A Group
4.2 4.2.1
Table 4.17 lists Registers with Write-Only Bits and registers whose function differs between reading and writing. Set these registers with immediate values. When establishing the next value by altering the existing value, write the existing value to the RAM as well as to the register. Transfer the next value to the register after making changes in the RAM.
Table 4.17 Registers with Write-Only Bits
Register Watchdog Timer Reset Register Watchdog Timer Start Register Timer A0 Register Timer A1 Register Timer A2 Register Timer A3 Register Timer A4 Register Timer A1-1 Register Timer A2-1 Register Timer A4-1 Register Three-Phase Output Buffer Register 0 Three-Phase Output Buffer Register 1 Dead Time Timer Timer B2 Interrupt Generation Frequency Set Counter UART0 Bit Rate Register UART1 Bit Rate Register UART2 Bit Rate Register UART5 Bit Rate Register UART6 Bit Rate Register UART7 Bit Rate Register UART0 Transmit Buffer Register UART1 Transmit Buffer Register UART2 Transmit Buffer Register UART5 Transmit Buffer Register UART6 Transmit Buffer Register UART7 Transmit Buffer Register SI/O3 Bit Rate Register SI/O4 Bit Rate Register I2C0 Control Register 1 I2C0 Status Register 0
Symbol WDTR WDTS TA0 TA1 TA2 TA3 TA4 TA11 TA21 TA41 IDB0 IDB1 DTT ICTB2 U0BRG U1BRG U2BRG U5BRG U6BRG U7BRG U0TB U1TB U2TB U5TB U6TB U7TB S3BRG S4BRG S3D0 S10
Address 037Dh 037Eh 0327h to 0326h 0329h to 0328h 032Bh to 032Ah 032Dh to 032Ch 032Fh to 032Eh 0303h to 0302h 0305h to 0304h 0307h to 0306h 030Ah 030Bh 030Ch 030Dh 0249h 0259h 0269h 0289h 0299h 02A9h 024Bh to 024Ah 025Bh to 025Ah 026Bh to 026Ah 028Bh to 028Ah 029Bh to 029Ah 02ABh to 02AAh 0273h 0277h 02B6h 02B8h
M16C/64A Group
5. Electrical Characteristics
5.
5.1
Electrical Characteristics
Electrical Characteristics (Common to 3 V and 5 V) Absolute Maximum Rating
Absolute Maximum Ratings
Parameter Supply voltage Analog supply voltage Input voltage RESET, CNVSS, BYTE, P6_0 to P6_7, P7_2 to P7_7, P8_0 to P8_4, P8_6, P8_7, P9_0 to P9_7, P10_0 to P10_7 XIN P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7 P7_0, P7_1, P8_5 Condition VCC1 = AVCC VCC2 VCC1 = AVCC Rated Value 0.3 to 6.5 0.3 to VCC1 + 0.1 0.3 to 6.5 0.3 to VCC1 + 0.3 Unit V V V V
5.1.1
Table 5.1
Symbol
V V
VO
Output voltage P6_0 to P6_7, P7_2 to P7_7, P8_0 to P8_4, P8_6, P8_7, P9_0 to P9_7, P10_0 to P10_7 XOUT P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7 P7_0, P7_1, P8_5
V mW C
Pd Topr
Power consumption Operating ambient temperature When the microcomputer is operating Flash program erase
Tstg
Storage temperature
M16C/64A Group
5. Electrical Characteristics
5.1.2
Table 5.2
Symbol VCC1, VCC2 AVCC VSS AVSS VIH
0.8VCC1
VCC1
0.8VCC1 0 0 0
V V V V
VIL
P3_1 to P3_7, P4_0 to P4_7, P5_0 to P5_7 P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, P3_0 (in single-chip mode) P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, P3_0 (data input in memory expansion and microprocessor mode) P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_7, P9_0 to P9_7, P10_0 to P10_7 XIN, RESET, CNVSS, BYTE
0.2VCC1
P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7, P6_0 to P6_7, P7_2 to P7_7, P8_0 to P8_4, P8_6, P8_7, P9_0 to P9_7, P10_0 to P10_7
10.0
mA
High average P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, output P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7, current P6_0 to P6_7, P7_2 to P7_7, P8_0 to P8_4, P8_6, P8_7, P9_0 to P9_7, P10_0 to P10_7
5.0
mA
Notes: 1. Referenced to VCC1 = VCC2 = 2.7 to 5.5 V at Topr = 20 to 85C/-40 to 85C unless otherwise specified. 2. The average output current is the mean value within 100 ms. 3. The total IOL(peak) for ports P0, P1, P2, P8_6, P8_7, P9, and P10 must be 80 mA max. The total IOL(peak) for ports P3, P4, P5, P6, P7, and P8_0 to P8_5 must be 80 mA max. The total IOH(peak) for ports P0, P1, and P2 must be 40 mA max. The total IOH(peak) for ports P3, P4, and P5 must be 40 mA max. The total IOH(peak) for ports P6, P7_2 to P7_7 and P8_0 to P8_4 must be 40 mA max. IOH(peak) for ports P8_6, P8_7, P9, and P10 must be 40 mA max.
M16C/64A Group
5. Electrical Characteristics
Table 5.3
Symbol
IOL(peak) Low peak P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, output current P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7, P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_7, P9_0 to P9_7, P10_0 to P10_7 IOL(avg) Low average P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, output current P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7, P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_7, P9_0 to P9_7, P10_0 to P10_7 Main clock input oscillation frequency Sub-clock oscillation frequency PLL clock oscillation frequency CPU operation clock PLL frequency synthesizer stabilization wait time VCC1 = 5.0 V VCC1 = 3.0 V VCC1 = 2.7 V to 5.5 V 10 2 VCC1 = 2.7 V to 5.5 V 2 32.768
5.0
mA
20 50 25 25 2 3
Notes: 1. Referenced to VCC1 = VCC2 = 2.7 to 5.5 V at Topr = 20 to 85C/-40 to 85C unless otherwise specified. 2. The average output current is the mean value within 100 ms. 3. The total IOL(peak) for ports P0, P1, P2, P8_6, P8_7, P9, and P10 must be 80 mA max. The total IOL(peak) for ports P3, P4, P5, P6, P7, and P8_0 to P8_5 must be 80 mA max. The total IOH(peak) for ports P0, P1, and P2 must be 40 mA max. The total IOH(peak) for ports P3, P4, and P5 must be 40 mA max. The total IOH(peak) for ports P6, P7_2 to P7_7 and P8_0 to P8_4 must be 40 mA max. IOH(peak) for ports P8_6, P8_7, P9, and P10 must be 40 mA max.
M16C/64A Group
5. Electrical Characteristics
5.1.3
Table 5.4
Symbol INL
LSB
LSB
Absolute accuracy
10bit
VCC1 = AN0 to AN7 input, 5.0 V AN0_0 to AN0_7 input, AN2_0 to AN2_7 input, ANEX0, ANEX1 input VCC1 = AN0 to AN7 input, 3.3 V AN0_0 to AN0_7 input, AN2_0 to AN2_7 input, ANEX0, ANEX1 input VCC1 = AN0 to AN7 input, 3.0 V AN0_0 to AN0_7 input, AN2_0 to AN2_7 input, ANEX0, ANEX1 input
LSB
LSB
LSB
Tolerance level impedance Differential non-linearity error Offset error Gain error 10-bit conversion time Sampling time Reference voltage Analog input voltage
(4)
Notes: 1. Referenced to VCC1 = AVCC = 3.0 to 5.5 V VCC2 VREF, VSS = AVSS = 0 V at Topr = -20 to 85C/-40 to 85C unless otherwise specified. 2. Set AD frequency as follows: When VCC1 = 4.0 to 5.5 V, 2 MHz AD 25 MHz When VCC1 = 3.2 to 4.0 V, 2 MHz AD 16 MHz When VCC1 = 3.0 to 3.2 V, 2 MHz AD 10 MHz 3. Use when AVCC = VCC1. 4. When VCC1 VCC2, do not input the voltage over VCC2 to AN2_0 to AN2_7 and AN0_0 to AN0_7 input.
M16C/64A Group
5. Electrical Characteristics
5.1.4
Table 5.5
Symbol tSU RO IVREF
Notes: 1. Referenced to VCC1 = AVCC = VREF = 3.0 to 5.5 V, VSS = AVSS = 0 V at Topr = -20 to 85C/-40 to 85C unless otherwise specified. 2. This applies when using one D/A converter, with the D/A register for the unused D/A converter set to 00h. 3. The current consumption of the A/D converter is not included. Also, the IVREF of the D/A converter will flow even if the ADSTBY bit in the ADCON1 register is 0 (A/D operation stopped (standby)).
M16C/64A Group
5. Electrical Characteristics
5.1.5
Table 5.6
Symbol -
Notes: 1. Set the PM17 bit in the PM1 register to 1 (wait state). 2. When the frequency is over this value, set the FMR17 bit in the FMR1 register to 0 (one wait) or the PM17 bit in the PM1 register to 1 (wait state)
Table 5.7
Symbol tPS -
Notes: 1. VCC1 = 2.7 to 5.5 V at Topr = 0 to 60C, unless otherwise specified. 2. Definition of program and erase cycles The program and erase cycles refer to the number of per-block erasures. If the program and erase cycles are n (n=1,000), each block can be erased n times. For example, if a 4 Kbyte block is erased after writing two word data 1,024 times, each to a different address, this counts as one program and erase cycles. Data cannot be written to the same address more than once without erasing the block (rewrite prohibited). 3. Cycles to guarantee all electrical characteristics after program and erase. (1 to Min. value can be guaranteed). 4. In a system that executes multiple programming operations, the actual erasure count can be reduced by writing to sequential addresses in turn so that as much of the block as possible is used up before performing an erase operation. For example, when programming groups of 16 bytes, the effective number of rewrites can be minimized by programming up to 128 groups before erasing them all in one operation. It is also advisable to retain data on the erasure cycles of each block and limit the number of erase operations to a certain number. 5. If an error occurs during block erase, attempt to execute the clear status register command, then execute the block erase command at least three times until the erase error does not occur. 6. Customers desiring program/erase failure rate information should contact their Renesas technical support representative. 7. The data hold time includes time that the power supply is off or the clock is not supplied.
M16C/64A Group
5. Electrical Characteristics
Table 5.8
Symbol tPS -
Program/erase cycles (2, 4, 5) Two words program time Lock bit program time Block erase time Program, erase voltage Read voltage Program, erase temperature
Flash Memory Circuit Stabilization Wait Time Data hold time (7)
Notes: 1. VCC1 = 2.7 to 5.5 V at Topr = 20 to 85C/40 to 85C, unless otherwise specified. 2. Definition of program and erase cycles The program and erase cycles refer to the number of per-block erasures. If the program and erase cycles are n (n=10,000), each block can be erased n times. For example, if a 4 Kbyte block is erased after writing two word data 1,024 times, each to a different address, this counts as one program and erase cycles. Data cannot be written to the same address more than once without erasing the block (rewrite prohibited). 3. Cycles to guarantee all electrical characteristics after program and erase. (1 to Min. value can be guaranteed). 4. In a system that executes multiple programming operations, the actual erasure count can be reduced by writing to sequential addresses in turn so that as much of the block as possible is used up before performing an erase operation. For example, when programming groups of 16 bytes, the effective number of rewrites can be minimized by programming up to 128 groups before erasing them all in one operation. In addition, averaging the erasure cycles between blocks A and B can further reduce the actual erasure cycles. It is also advisable to retain data on the erasure cycles of each block and limit the number of erase operations to a certain number. 5. If an error occurs during block erase, attempt to execute the clear status register command, then execute the block erase command at least three times until the erase error does not occur. 6. Customers desiring program/erase failure rate information should contact their Renesas technical support representative. 7. The data hold time includes time that the power supply is off or the clock is not supplied.
M16C/64A Group
5. Electrical Characteristics
5.1.6
Circuit
and
Power
Supply
Circuit
Electrical
Table 5.9
Symbol Vdet0 td(E-A)
Notes: 1. The measurement condition is Topr = 20 to 85C/40 to 85C. 2. Select the voltage detection level with the VDSEL1 bit in the OFS1 address. 3. Necessary time until the voltage detection circuit operates when setting to 1 again after setting the VC25 bit in the VCR2 register to 0.
Table 5.10
Symbol Vdet1
Condition
Standard Min. 2.79 3.54 3.94 Typ. 3.09 3.84 4.44 1.8 100 Max. 3.39 4.14 4.94
Unit V V V A s
td(E-A)
Voltage detection circuit self power consumption Waiting time until voltage detection circuit operation starts (3)
Notes: 1. The measurement condition is Topr = 20 to 85C/40 to 85C. 2. Select the voltage detection level with bits VD1S0 to VD1S3 in the VD1LS register. 3. Necessary time until the voltage detection circuit operates when setting to 1 again after setting the VC26 bit in the VCR2 register to 0.
Table 5.11
Symbol Vdet2 td(E-A)
Notes: 1. The measurement condition is Topr = 20 to 85C/40 to 85C. 2. Necessary time until the voltage detection circuit operates after setting to 1 again after setting the VC27 bit in the VCR2 register to 0.
Table 5.12
Symbol trth
Notes: 1. The measurement condition is Topr = 20 to 85C/ 40 to 85C, unless otherwise specified. 2. To use the power-on reset function, enable voltage monitor 0 reset by setting the LVDAS bit in the OFS1 address to 0.
M16C/64A Group
5. Electrical Characteristics
Vdet0 (1) External Power VCC1 0.1 V tw(por) (2) Voltage detection 0 circuit response time t rth t rth
Vdet0 (1)
32
32
Notes: 1. Vdet0 indicates the voltage detection level of the voltage detection 0 circuit. Refer to 7. Voltage Detector for details. 2. When using power-on reset, hold the external power VCC1 at or below the valid voltage (0.1 V) during tw(por), and then turn it on. tw(por) is 30 s or more when -20 C Topr 85 C, and 3000 s or more when -40 C Topr < -20 C.
Figure 5.1
Table 5.13
Symbol td(P-R) td(R-S) td(W-S)
Notes: 1. The measurement condition is VCC1 = 2.7 to 5.5 V and Topr = 25C. 2. Waiting time until the internal power supply generation circuit stabilizes when power is on.
M16C/64A Group
5. Electrical Characteristics
td(R-S) STOP release time td(W-S) Low power mode wait mode release time
Interrupt for (a) Stop mode release or (b) Wait mode release
CPU clock (a) (b) td(E-A) Voltage detector operation start time td(R-S) td(W-S)
Voltage detector
Stop
Operate
td(E-A)
Figure 5.2
M16C/64A Group
5. Electrical Characteristics
5.1.7
Table 5.14
Symbol fOCO-S
Note: 1. VCC1 = 2.7 to 5.5 V, Topr = 20 to 85C/40 to 85C, unless otherwise specified.
M16C/64A Group
5. Electrical Characteristics
5.2 5.2.1
Table 5.15
Symbol VOH
Measuring Condition IOH = 5 mA IOH = 5 mA IOH = 200 A IOH = 200 A IOH = 1 mA IOH = 0.5 mA With no load applied With no load applied IOL = 5 mA IOL = 5 mA IOL = 200 A IOL = 200 A IOL = 1 mA IOL = 0.5 mA With no load applied With no load applied
Standard Min. VCC1 2.0 VCC2 2.0 VCC1 0.3 VCC2 0.3 VCC1 2.0 VCC1 2.0 2.6 2.2 2.0 2.0 0.45 0.45 2.0 2.0 0 0 Typ. Max. VCC1 VCC2 VCC1 VCC2 VCC1 VCC1
Unit V
VOH
High output P6_0 to P6_7, P7_2 to P7_7, P8_0 to P8_4, voltage P8_6, P8_7, P9_0 to P9_7, P10_0 to P10_7 P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7
VOH
XOUT
HIGHPOWER LOWPOWER
XCOUT
HIGHPOWER LOWPOWER
VOL
Low output P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_7, voltage P9_0 to P9_7, P10_0 to P10_7 P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7
VOL
Low output P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_7, voltage P9_0 to P9_7, P10_0 to P10_7 P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7
VOL
XOUT
HIGHPOWER LOWPOWER
XCOUT
HIGHPOWER LOWPOWER
Notes: 1. Referenced to VCC1 = VCC2 = 4.2 to 5.5 V, VSS = 0 V at Topr = 20 to 85C/40 to 85C, f(BCLK) = 25 MHz unless otherwise specified. 2. When VCC1 VCC2, refer to 5 V or 3 V standard depending on the voltage.
M16C/64A Group
5. Electrical Characteristics
Table 5.16
Symbol
0.5
2.0 5.0
V A
IIL
VI = 0 V
5.0
VI = 0 V
30
50
100
Feedback resistance XIN Feedback resistance XCIN RAM retention voltage In stop mode 1.8
1.5 8
M M V
Notes: 1. Referenced to VCC1 = VCC2 = 4.2 to 5.5 V, VSS = 0 V at Topr = 20 to 85C/40 to 85C, f(BCLK) = 25 MHz unless otherwise specified. 2. When VCC1 VCC2, refer to 5 V or 3 V standard depending on the voltage.
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 5 V
Table 5.17 Electrical Characteristics (3) (1) R5F364A6NFA, R5F364A6NFB, R5F364A6DFA, R5F364A6DFB, R5F364AENFA, R5F364AENFB, R5F364AEDFA, R5F364AEDFB
Symbol ICC Parameter Power supply current High-speed mode Measuring Condition Min. Standard Unit Typ. Max. 20.0 mA
f(BCLK) = 25 MHz XIN = 4.2 MHz (square wave), PLL multiplied by 6 In single-chip, 125 kHz on-chip oscillator stop mode, the output f(BCLK) =25 MHz, A/D conversion pin are open and XIN = 4.2 MHz (square wave), other pins are VSS PLL multiplied by 6 125 kHz on-chip oscillator stop f(BCLK) = 20 MHz XIN = 20 MHz (square wave), 125 kHz on-chip oscillator stop 125 kHz on-chip Main clock stop oscillator mode 125 kHz on-chip oscillator on, no division Low-power mode f(BCLK) = 32 kHz In low-power mode, FMR22 = FMR23 = 1 on flash memory (2) f(BCLK) = 32 kHz In low-power mode, on RAN (2) Wait mode Main clock stop 125 kHz on-chip oscillator on Peripheral clock operation Topr = 25C f(BCLK) = 32 kHz (oscillation capacity High) 125 kHz on-chip oscillator stop Peripheral clock operation Topr = 25C f(BCLK) = 32 kHz (oscillation capacity Low) 125 kHz on-chip oscillator stop Peripheral clock operation Topr = 25C Stop mode Main clock stop 125 kHz on-chip oscillator stop Peripheral clock stop Topr = 25C
20.7
mA
16.0 500.0
mA A
160.0
45.0
20.0
11.0
6.0
1.7
Notes: 1. Referenced to VCC1 = VCC2 = 4.2 to 5.5 V, VSS = 0 V at Topr = 20 to 85C/40 to 85C, f(BCLK) = 25 MHz unless otherwise specified. 2. This indicates the memory in which the program to be executed exists.
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 5 V
Table 5.18 Electrical Characteristics (4) R5F364AMNFA, R5F364AMNFB, R5F364AMDFA, R5F364AMDFB
Symbol ICC Parameter Power supply current Measuring Condition Min. Standard Unit Typ. Max. TBD mA
(1)
High-speed mode f(BCLK) = 25 MHz XIN = 4.2 MHz (square wave), PLL multiplied by 6 In single-chip, 125 kHz on-chip oscillator stop mode, the output f(BCLK) = 25 MHz, A/D conversion pin are open and XIN = 4.2 MHz (square wave), other pins are VSS PLL multiplied by 6 125 kHz on-chip oscillator stop f(BCLK) = 20 MHz XIN = 20 MHz (square wave), 125 kHz on-chip oscillator stop 125 kHz on-chip Main clock stop oscillator mode 125 kHz on-chip oscillator on, no division Low-power mode f(BCLK) = 32 kHz In low-power mode, FMR22 = FMR23 = 1 on flash memory (2) f(BCLK) = 32 kHz In low-power mode, on RAN (2) Wait mode Main clock stop 125 kHz on-chip oscillator on Peripheral clock operation Topr = 25C f(BCLK) = 32 kHz (oscillation capacity High) 125 kHz on-chip oscillator stop Peripheral clock operation Topr = 25C f(BCLK) = 32 kHz (oscillation capacity Low) 125 kHz on-chip oscillator stop Peripheral clock operation Topr = 25C Stop mode Main clock stop 125 kHz on-chip oscillator stop Peripheral clock stop Topr = 25C
TBD
mA
TBD TBD
mA A
TBD
TBD
TBD
TBD
TBD
TBD
Notes: 1. Referenced to VCC1 = VCC2 = 4.2 to 5.5 V, VSS = 0 V at Topr = 20 to 85C/40 to 85C, f(BCLK) = 25 MHz unless otherwise specified. 2. This indicates the memory in which the program to be executed exists.
M16C/64A Group
5. Electrical Characteristics
(VCC1 = VCC2 = 5 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
Table 5.19
Symbol tc tw(H) tw(L) tr tf Note: 1. External clock input cycle time External clock input high pulse width External clock input low pulse width External clock rise time External clock fall time The condition is VCC1 = VCC2 = 3.0 to 5.0 V.
Table 5.20
Symbol tc(TA) tw(TAH) tw(TAL)
Table 5.21
Symbol tc(TA) tw(TAH) tw(TAL)
Table 5.22
Symbol tc(TA) tw(TAH) tw(TAL)
Table 5.23
Symbol tw(TAH) tw(TAL)
Table 5.24
Symbol tc(TA)
tsu(TAIN-TAOUT) tsu(TAOUT-TAIN)
M16C/64A Group
5. Electrical Characteristics
VCC1 = Timing Requirements (VCC1 = VCC2 = 5 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
Table 5.25
Symbol tc(TB) tw(TBH) tw(TBL) tc(TB) tw(TBH) tw(TBL)
VCC2 = 5 V
Table 5.26
Symbol tc(TB) tw(TBH) tw(TBL)
Table 5.27
Symbol tc(TB) tw(TBH) tw(TBL)
Table 5.28
Symbol tc(CK) tw(CKH) tw(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D)
Serial Interface
Parameter CLKi input cycle time CLKi input high pulse width CLKi input low pulse width TXDi output delay time TXDi hold time RXDi input setup time RXDi input hold time 0 70 90 Standard Min. 200 100 100 80 Max. Unit ns ns ns ns ns ns ns
Table 5.29
Symbol tw(INH) tw(INL)
M16C/64A Group
5. Electrical Characteristics
VCC1 = Timing Requirements (VCC1 = VCC2 = 5 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
VCC2 = 5 V
VCC1 = VCC2 = 5 V
XIN input tr t w(H) tf tc t w(L)
tc(TA) t w(TAH) TAiIN input t w(TAL) tc(UP) t w(UPH) TAiOUT input t w(UPL)
Two-phase pulse input in event counter mode tc(TA) TAiIN input tsu(TAIN-TAOUT) TAiOUT input tsu(TAOUT-TAIN) tsu(TAIN-TAOUT) tsu(TAOUT-TAIN)
Figure 5.3
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 5 V
tc(CK) t w(CKH) CLKi t w(CKL) th(C-Q) TXDi td(C-Q) RXDi t w(INL) INTi input t w(INH) tsu(D-C) th(C-D)
Figure 5.4
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 5 V 5.2.3 Timing Requirements (Memory Expansion Mode and Microprocessor Mode)
(VCC1 = VCC2 = 5 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
Table 5.30
Symbol tac1(RD-DB) tac2(RD-DB) tac3(RD-DB) tsu(DB-RD) tsu(RDY-BCLK) tsu(HOLD-BCLK) th(RD-DB) th(BCLK-RDY) th(BCLK-HOLD)
f ( BCLK )
2.
f ( BCLK )
n is 1 for 1 wait setting, 2 for 2 waits setting and 3 for 3 waits setting.
3.
f ( BCLK )
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 5 V
BCLK
RD (Separate bus) WR, WRL, WRH (Separate bus) RD (Multiplexed bus) WR, WRL, WRH (Multiplexed bus)
BCLK
th(BCLK-HOLD)
Note: 1. These pins are high-impedance regardless of the input level of the BYTE pin, PM06 bit in PM0 register, and PM11 bit in PM1 register. Measuring conditions VCC1 = V CC2 = 5 V Input timing voltage: V = 1.0 V, V = 4.0 V IL IH Output timing voltage: V = 2.5 V, V = 2.5 V OL OH
Figure 5.5
Timing Diagram
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 5 V 5.2.4 Switching Characteristics (Memory Expansion Mode and Microprocessor Mode (in No Wait State Setting))
(VCC1 = VCC2 = 5 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
Table 5.31
Symbol td(BCLK-AD) th(BCLK-AD) th(RD-AD) th(WR-AD) td(BCLK-CS) th(BCLK-CS) td(BCLK-ALE) th(BCLK-ALE) td(BCLK-RD) th(BCLK-RD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) th(BCLK-DB) td(DB-WR) th(WR-DB) td(BCLK-HLDA) Address output delay time Address output hold time (in relation to BCLK) Address output hold time (in relation to RD) Address output hold time (in relation to WR) Chip select output delay time Chip select output hold time (in relation to BCLK) ALE signal output delay time ALE signal output hold time RD signal output delay time RD signal output hold time WR signal output delay time WR signal output hold time Data output delay time (in relation to BCLK) Data output hold time (in relation to BCLK) (3) Data output delay time (in relation to WR) Data output hold time (in relation to WR)
HLDA output delay time
(3)
Memory Expansion Mode and Microprocessor Mode (in No Wait State Setting)
Parameter Measuring Condition Standard Min. Max. 25 0 0 (Note 2) 25 0 15 4 See
Figure 5.6
Unit ns ns ns ns ns ns ns ns
25 0 25 0 40 0 (Note 1) (Note 2) 40
ns ns ns ns ns ns ns ns ns
f ( BCLK )
2.
Calculated according to the BCLK frequency as follows: f ( BCLK ) This standard value shows the timing when the output is off, and does not show hold time of data bus. Hold time of data bus varies with capacitor volume and pull-up (pull-down) resistance value. Hold time of data bus is expressed in t = CR ln(1VOL/VCC2) by a circuit of the right figure. For example, when VOL = 0.2VCC2, C = 30 pF, R = 1 k, hold time of output low level is t = 30 pF 1 k In(1 0.2VCC2/VCC2) = 6.7 ns.
9 0.5x10 --------------------- 10 [ ns ] -
3.
R DBi C
M16C/64A Group
5. Electrical Characteristics
P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10
30 pF
Figure 5.6
M16C/64A Group
5. Electrical Characteristics
Memory Expansion Mode and Microprocessor Mode (in no wait state setting)
Read timing
VCC1 = VCC2 = 5 V
BCLK td(BCLK-CS)
25ns(max.)
th(BCLK-CS)
0ns(min.)
CSi tcyc
td(BCLK-AD)
25ns(max.)
th(BCLK-AD)
0ns(min.)
ADi BHE
td(BCLK-ALE) 15ns(max.)
th(BCLK-ALE)
-4ns(min.)
th(RD-AD)
0ns(min.)
ALE td(BCLK-RD) 25ns(max.) RD tac1(RD-DB) (0.5 tcyc -45)ns(max.) Hi-Z DBi tsu(DB-RD)
40ns(min.)
th(BCLK-RD)
0ns(min.)
th(RD-DB)
0ns(min.)
Write timing
BCLK td(BCLK-CS)
25ns(max.)
th(BCLK-CS)
0ns(min.)
CSi tcyc
td(BCLK-AD)
25ns(max.)
th(BCLK-AD)
0ns(min.)
ADi BHE
td(BCLK-ALE) 15ns(max.)
th(BCLK-ALE)
-4ns(min.)
ALE td(BCLK-WR)
25ns(max.)
th(BCLK-DB)
0ns(min.)
DBi
Hi-Z td(DB-WR) (0.5 tcyc -40)ns(min.) tcyc = 1 f(BCLK) th(WR-DB) (0.5 tcyc -10)ns(min.)
Measuring conditions VCC1 = V CC2 = 5 V Input timing voltage: V = 0.8 V, V = 2.0 V IL IH Output timing voltage: V = 0.4 V, V = 2.4 V OL OH
Figure 5.7
Timing Diagram
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 5 V 5.2.5 Switching Characteristics (Memory Expansion Mode and Microprocessor Mode (in 1 to 3 Waits Setting and When Accessing External Area))
(VCC1 = VCC2 = 5 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
Table 5.32 Memory Expansion Mode and Microprocessor Mode (in 1 to 3 Waits Setting and When Accessing External Area)
Parameter Address output delay time Address output hold time (in relation to BCLK) Address output hold time (in relation to RD) Address output hold time (in relation to WR) Chip select output delay time Chip select output hold time (in relation to BCLK) ALE signal output delay time ALE signal output hold time RD signal output delay time RD signal output hold time WR signal output delay time WR signal output hold time Data output delay time (in relation to BCLK) Data output hold time (in relation to BCLK) Data output delay time (in relation to WR) Data output hold time (in relation to WR)(3) HLDA output delay time
(3)
Symbol td(BCLK-AD) th(BCLK-AD) th(RD-AD) th(WR-AD) td(BCLK-CS) th(BCLK-CS) td(BCLK-ALE) th(BCLK-ALE) td(BCLK-RD) th(BCLK-RD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) th(BCLK-DB) td(DB-WR) th(WR-DB) td(BCLK-HLDA)
Measuring Condition
Unit ns ns ns ns ns ns ns ns
See
Figure 5.6
25 0 25 0 40 0 (Note 1) (Note 2) 40
ns ns ns ns ns ns ns ns ns
f ( BCLK )
n is 1 for 1 wait setting, 2 for 2 waits setting and 3 for 3 waits setting. When n = 1, f(BCLK) is 12.5 MHz or less.
2.
Calculated according to the BCLK frequency as follows: f ( BCLK ) This standard value shows the timing when the output is off, and does not show hold time of data bus. Hold time of data bus varies with capacitor volume and pullup (pull-down) resistance value. Hold time of data bus is expressed in t = CR ln(1 VOL/VCC2) by a circuit of the right figure. For example, when VOL = 0.2VCC2, C = 30 pF, R = 1k, hold time of output low level is t = 30 pF 1 k In(1 0.2VCC2/VCC2) = 6.7 ns.
9 0.5x10 --------------------- 10 [ ns ] -
3.
R DBi C
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 5 V
th(BCLK-CS)
0ns(min.)
CSi tcyc
td(BCLK-AD)
25ns(max.)
th(BCLK-AD)
0ns(min.)
ADi BHE
td(BCLK-ALE)
15ns(max.)
th(BCLK-ALE)
-4ns(min.)
th(RD-AD)
0ns(min.)
ALE td(BCLK-RD)
25ns(max.)
th(BCLK-RD)
0ns(min.) {(n+0.5) t cyc - 45}ns(max.)
RD
tac2(RD-DB)
DBi
Hi-Z tsu(DB-RD)
40ns(min.)
th(RD-DB)
0ns(min.)
Write timing
BCLK td(BCLK-CS)
25ns(max.)
th(BCLK-CS)
0ns(min.)
CSi tcyc
td(BCLK-AD)
25ns(max.)
th(BCLK-AD)
0ns(min.)
ADi BHE
td(BCLK-ALE)
15ns(max.)
th(BCLK-ALE)
-4ns(min.)
th(WR-AD)
(0.5 tcyc -10)ns(min.)
ALE td(BCLK-WR)
25ns(max.)
th(BCLK-WR)
0ns(min.)
td(BCLK-DB)
40ns(max.)
th(BCLK-DB)
0ns(min.)
th(WR-DB)
tcyc =
Measuring conditions VCC1 = V CC2 = 5 V Input timing voltage: V = 0.8 V, V = 2.0 V IL IH Output timing voltage: V = 0.4 V, V = 2.4 V OL OH
Figure 5.8
Timing Diagram
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 5 V 5.2.6 Switching Characteristics (Memory Expansion Mode and Microprocessor Mode (in 2 or 3 Waits Setting, and When Accessing External Area and Using Multiplexed Bus))
(VCC1 = VCC2 = 5 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
Table 5.33 Memory Expansion Mode and Microprocessor Mode (in 2 or 3 Waits Setting, and When Accessing External Area and Using Multiplexed Bus) (5)
Parameter Address output delay time Address output hold time (in relation to BCLK) Address output hold time (in relation to RD) Address output hold time (in relation to WR) Chip select output delay time Chip select output hold time (in relation to BCLK) Chip select output hold time (in relation to RD) Chip select output hold time (in relation to WR) RD signal output delay time RD signal output hold time WR signal output delay time WR signal output hold time Data output delay time (in relation to BCLK) Data output hold time (in relation to BCLK) Data output delay time (in relation to WR) Data output hold time (in relation to WR)
HLDA output delay time
Symbol td(BCLK-AD) th(BCLK-AD) th(RD-AD) th(WR-AD) td(BCLK-CS) th(BCLK-CS) th(RD-CS) th(WR-CS) td(BCLK-RD) th(BCLK-RD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) th(BCLK-DB) td(DB-WR) th(WR-DB)
td(BCLK-HLDA)
Measuring Condition
Unit ns ns ns ns ns ns ns ns ns ns ns ns
See
Figure 5.6
0 40 0 (Note 2) (Note 1) 40 15
ns ns ns ns ns ns ns ns ns ns ns
ALE signal output delay time (in relation to BCLK) ALE signal output hold time (in relation to BCLK) ALE signal output delay time (in relation to Address) ALE signal output hold time (in relation to Address) RD signal output delay from the end of address WR signal output delay from the end of address Address output floating start time
4
(Note 3) (Note 4) 0 0 8
ns
f ( BCLK )
2.
Calculated according to the BCLK frequency as follows: 9 ( n 0.5 ) x10 ----------------------------------- 40 [ ns ] n is 2 for 2-wait setting, 3 for 3-wait setting. -
f ( BCLK )
3.
f ( BCLK )
4.
f ( BCLK )
5.
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 5 V
(in 2 or 3 waits setting, and when accessing external area and using multiplexed bus )
BCLK
td(BCLK-CS)
25ns(max.)
th(BCLK-CS) tcyc
(0.5 tcyc -10)ns(min.)
th(RD-CS)
0ns(min.)
CSi td(AD-ALE) (0.5 tcyc -25ns(min.) ADi /DBi th(ALE-AD) (0.5 tcyc -15ns(min.) tdz(RD-AD)
8ns(max.)
Address
Data input
Address
th(RD-DB)
0ns(min.)
td(BCLK-AD)
25ns(max.)
td(AD-RD)
0ns(min.)
th(BCLK-AD)
0ns(min.)
ADi BHE
td(BCLK-ALE) 15ns(max.)
th(BCLK-ALE)
-4ns(min.)
ALE
RD
Write timing
BCLK td(BCLK-CS)
25ns(max.)
tcyc
th(BCLK-CS)
0ns(min.)
CSi td(BCLK-DB)
40ns(max.)
th(BCLK-DB)
0ns(min.)
ADi /DBi
Address
Data output
Address
ADi BHE
td(BCLK-ALE) 15ns(max.)
th(BCLK-ALE)
-4ns(min.)
td(AD-WR)
0ns(min.)
Measuring conditions VCC1 = V CC2 = 5 V Input timing voltage: V = 0.8 V, V = 2.0 V IL IH Output timing voltage: V = 0.4 V, V = 2.4 V OL OH
Figure 5.9
Timing Diagram
M16C/64A Group
5. Electrical Characteristics
5.3 5.3.1
Table 5.34
Symbol VOH
Unit V
IOH = 1 mA
VCC2 0.5
VCC2
VOH
XOUT
HIGHPOWER LOWPOWER
IOH = 0.1 mA IOH = 50 A With no load applied With no load applied IOL = 1 mA
VCC1 VCC1
XCOUT
HIGHPOWER LOWPOWER
V 0.5 V
Low output P6_0 to P6_7, P7_0 to P7_7, voltage P8_0 to P8_7, P9_0 to P9_7, P10_0 to P10_7 P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7
IOL = 1 mA
0.5
VOL
XOUT
HIGHPOWER LOWPOWER
IOL = 0.1 mA IOL = 50 A With no load applied With no load applied 0.5 0 0
0.5 0.5
XCOUT
HIGHPOWER LOWPOWER
V 1.0 V
VT+-VT- Hysteresis HOLD, RDY, TA0IN to TA4IN, TB0IN to TB5IN, INT0 to INT7, NMI, ADTRG, CTS0 to CTS2, CTS5 to CTS7, SCL0 to SCL2, SCL5 to SCL7, SDA0 to SDA2, SDA5 to SDA7, CLK0 to CLK7, TA0OUT to TA4OUT, KI0 to KI3, RXD0 to RXD2, RXD5 to RXD7, SIN3, SIN4, SD, PMC0, PMC1, SCLMM, SDAMM, CEC VT+-VT- Hysteresis RESET IIH High input P0_0 to P0_7, P1_0 to P1_7, current P2_0 to P2_7, P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7, P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_7, P9_0 to P9_7, P10_0 to P10_7 XIN, RESET, CNVSS, BYTE VI = 3 V
0.5
1.0 4.0
V A
Notes: 1. Referenced to VCC1 = VCC2 = 2.7 to 3.3 V, VSS = 0 V at Topr = 20 to 85C/40 to 85C, f(BCLK) = 25 MHz unless otherwise specified. 2. When VCC1 VCC2, refer to 5 V or 3 V standard depending on the voltage.
M16C/64A Group
5. Electrical Characteristics
Table 5.35
Symbol IIL
P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7, P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_7, P9_0 to P9_7, P10_0 to P10_7 XIN, RESET, CNVSS, BYTE
RPULLUP Pull-up P0_0 to P0_7, P1_0 to P1_7, resistance P2_0 to P2_7, P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7, P6_0 to P6_7, P7_2 to P7_7, P8_0 to P8_4, P8_6, P8_7, P9_0 to P9_7, P10_0 to P10_7 RfXIN RfXCIN VRAM Feedback resistance XIN Feedback resistance XCIN RAM retention voltage
VI = 0 V
50
80
150
M M V
Notes: 1. Referenced to VCC1 = VCC2 = 2.7 to 3.3 V, VSS = 0 V at Topr = 20 to 85C/40 to 85C, f(BCLK) = 25 MHz unless otherwise specified. 2. When VCC1 VCC2, refer to 5 V or 3 V standard depending on the voltage.
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 3 V
Table 5.36 Electrical Characteristics (3) R5F364A6NFA, R5F364A6NFB, R5F364A6DFA, R5F364A6DFB, R5F364AENFA, R5F364AENFB, R5F364AEDFA, R5F364AEDFB
Symbol ICC Parameter Power supply current High-speed mode Measuring Condition Min. Standard Unit Typ. Max. 20.0 mA
(1)
f(BCLK) = 25 MHz XIN = 4.2 MHz (square wave), PLL multiplied by 6 In single-chip, 125 kHz on-chip oscillator stop mode, the output f(BCLK) = 25 MHz pin are open and XIN = 4.2 MHz (square wave), other pins are VSS PLL multiplied by 6 125 kHz on-chip oscillator stop f(BCLK) = 20 MHz XIN = 20 MHz (square wave) 125 kHz on-chip oscillator stop 125 kHz on-chip Main clock stop oscillator mode 125 kHz on-chip oscillator on, no division Low-power mode f(BCLK) = 32 MHz In low-power mode, FMR 22 = FMR23 = 1 on flash memory (2) f(BCLK) = 32 MHz In low-power mode, on RAN (2) Wait mode Main clock stop 125 kHz on-chip oscillator on Peripheral clock operating Topr = 25C f(BCLK) = 32 MHz (oscillation capacity High) 125 kHz on-chip oscillator stop Peripheral clock operating Topr = 25C f(BCLK) = 32kHz (oscillation capacity Low) 125 kHz on-chip oscillator stop Peripheral clock operating Topr = 25C Stop mode Main clock stop 125 kHz on-chip oscillator stop Peripheral clock stop Topr = 25C
20.7
mA
16.0 450.0
mA A
160.0
40.0
20.0
8.0
4.0
1.6
Notes: 1. Referenced to VCC1 = VCC2 = 2.7 to 3.3 V, VSS = 0 V at Topr = 20 to 85C/40 to 85C, f(BCLK) = 25 MHz unless otherwise specified. 2. This indicates the memory in which the program to be executed exists.
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 3 V
Table 5.37 Electrical Characteristics (4) R5F364AMNFA, R5F364AMNFB, R5F364AMDFA, R5F364AMDFB
Symbol ICC Parameter Power supply current High-speed mode Measuring Condition Min. Standard Unit Typ. Max. TBD mA
(1)
f(BCLK) = 25 MHz XIN = 4.2 MHz (square wave), PLL multiplied by 6 In single-chip, 125 kHz on-chip oscillator stop mode, the output f(BCLK) = 25 MHz pin are open and XIN = 4.2 MHz (square wave), other pins are VSS PLL multiplied by 6 125 kHz on-chip oscillator stop f(BCLK) = 20 MHz XIN = 20 MHz (square wave) 125 kHz on-chip oscillator stop 125 kHz on-chip Main clock stop oscillator mode 125 kHz on-chip oscillator on, no division Low-power mode f(BCLK) = 32 MHz In low-power mode, FMR 22 = FMR23 = 1 on flash memory (2) f(BCLK) = 32 MHz In low-power mode, on RAN (2) Wait mode Main clock stop 125 kHz on-chip oscillator on Peripheral clock operating Topr = 25C f(BCLK) = 32 MHz (oscillation capacity High) 125 kHz on-chip oscillator stop Peripheral clock operating Topr = 25C f(BCLK) = 32kHz (oscillation capacity Low) 125 kHz on-chip oscillator stop Peripheral clock operating Topr = 25C Stop mode Main clock stop 125 kHz on-chip oscillator stop Peripheral clock stop Topr = 25C
TBD
mA
TBD TBD
mA A
TBD
TBD
TBD
TBD
TBD
TBD
Notes: 1. Referenced to VCC1 = VCC2 = 2.7 to 3.3 V, VSS = 0 V at Topr = 20 to 85C/40 to 85C, f(BCLK) = 25 MHz unless otherwise specified. 2. This indicates the memory in which the program to be executed exists.
M16C/64A Group
5. Electrical Characteristics
(VCC1 = VCC2 = 3 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
Table 5.38
Symbol tc tw(H) tw(L) tr tf Note: 1. External clock input cycle time External clock input high pulse width External clock input low pulse width External clock rise time External clock fall time
Table 5.39
Symbol tc(TA) tw(TAH) tw(TAL)
Table 5.40
Symbol tc(TA) tw(TAH) tw(TAL)
Table 5.41
Symbol tc(TA) tw(TAH) tw(TAL)
Table 5.42
Symbol tw(TAH) tw(TAL)
Table 5.43
Symbol
tc(TA) tsu(TAIN-TAOUT) tsu(TAOUT-TAIN)
s
ns ns
M16C/64A Group
5. Electrical Characteristics
VCC1 Timing Requirements (VCC1 = VCC2 = 3 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
Table 5.44
Symbol tc(TB) tw(TBH) tw(TBL) tc(TB) tw(TBH) tw(TBL)
= VCC2 = 3 V
Table 5.45
Symbol tc(TB) tw(TBH) tw(TBL)
Table 5.46
Symbol tc(TB) tw(TBH) tw(TBL)
Table 5.47
Symbol tc(CK) tw(CKH) tw(CKL) td(C-Q) th(C-Q) tsu(D-C) th(C-D)
Serial Interface
Parameter CLKi input cycle time CLKi input high pulse width CLKi input low pulse width TXDi output delay time TXDi hold time RXDi input setup time RXDi input hold time 0 100 90 Standard Min. 300 150 150 160 Max. Unit ns ns ns ns ns ns ns
Table 5.48
Symbol tw(INH) tw(INL)
Unit ns ns
M16C/64A Group
5. Electrical Characteristics
VCC1 = Timing Requirements (VCC1 = VCC2 = 3 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
VCC2 = 3 V
VCC1 = VCC2 = 3 V
XIN input tr t w(H) tf tc t w(L)
tc(TA) t w(TAH) TAiIN input t w(TAL) tc(UP) t w(UPH) TAiOUT input t w(UPL)
Two-phase pulse input in event counter mode tc(TA) TAiIN input tsu(TAIN-TAOUT) TAiOUT input tsu(TAOUT-TAIN) tsu(TAIN-TAOUT) tsu(TAOUT-TAIN)
Figure 5.10
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 3 V
tc(CK) t w(CKH) CLKi t w(CKL) th(C-Q) TXDi td(C-Q) RXDi t w(INL) INTi input t w(INH) tsu(D-C) th(C-D)
Figure 5.11
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 3 V 5.3.3 Timing Requirements (Memory Expansion Mode and Microprocessor Mode)
(VCC1 = VCC2 = 3 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
Table 5.49
Symbol tac1(RD-DB) tac2(RD-DB) tac3(RD-DB) tsu(DB-RD) tsu(RDY-BCLK) tsu(HOLD-BCLK) th(RD-DB) th(BCLK-RDY) th(BCLK-HOLD)
f ( BCLK )
2.
f ( BCLK )
n is 1 for 1 wait setting, 2 for 2 waits setting and 3 for 3 waits setting.
3.
f ( BCLK )
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 3 V
BCLK
RD (Separate bus) WR, WRL, WRH (Separate bus) RD (Multiplexed bus) WR, WRL, WRH (Multiplexed bus)
BCLK
th(BCLK-HOLD)
Note: 1. These pins are high-impedance regardless of the input level of the BYTE pin, PM06 bit in PM0 register, and PM11 bit in PM1 register. Measuring conditions VCC1 = V CC2 = 3 V Input timing voltage: V = 0.6 V, V = 2.4 V IL IH Output timing voltage: V = 1.5 V, V = 1.5 V OL OH
Figure 5.12
Timing Diagram
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 3 V 5.3.4 Switching Characteristics (Memory Expansion Mode and Microprocessor Mode (in No Wait State Setting))
(VCC1 = VCC2 = 3 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
Table 5.50
Symbol td(BCLK-AD) th(BCLK-AD) th(RD-AD) th(WR-AD) td(BCLK-CS) th(BCLK-CS) td(BCLK-ALE) th(BCLK-ALE) td(BCLK-RD) th(BCLK-RD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) th(BCLK-DB) td(DB-WR) th(WR-DB) td(BCLK-HLDA)
Measuring Condition
Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
f ( BCLK )
2.
f ( BCLK )
This standard value shows the timing when the output is off, and does not show hold time of data bus. Hold time of data bus varies with capacitor volume and pull-up (pull-down) resistance value. Hold time of data bus is expressed in t= CR ln(1 VOL/VCC2) by a circuit of the right figure. For example, when VOL = 0.2VCC2, C = 30 pF, R = 1 k, hold time of output low level is t = 30 pF 1 k In(1 0.2VCC2/VCC2) = 6.7 ns.
R DBi C
M16C/64A Group
5. Electrical Characteristics
P0 P1 P2 P3 P4 P5 P6 P7 P8 P9 P10
30 pF
Figure 5.13
M16C/64A Group
5. Electrical Characteristics
Memory Expansion Mode and Microprocessor Mode (in no wait state setting)
Read timing
VCC1 = VCC2 = 3 V
BCLK td(BCLK-CS)
30ns(max.)
th(BCLK-CS)
0ns(min.)
CSi tcyc
td(BCLK-AD)
30ns(max.)
th(BCLK-AD)
0ns(min.)
ADi BHE
td(BCLK-ALE) 25ns(max.)
th(BCLK-ALE)
-4ns(min.)
th(RD-AD)
0ns(min.)
ALE td(BCLK-RD) 30ns(max.) RD tac1(RD-DB) (0.5 tcyc -60)ns(max.) Hi-Z DBi tsu(DB-RD)
50ns(min.)
th(BCLK-RD)
0ns(min.)
th(RD-DB)
0ns(min.)
Write timing
BCLK td(BCLK-CS)
30ns(max.)
th(BCLK-CS)
0ns(min.)
CSi tcyc
td(BCLK-AD)
30ns(max.)
th(BCLK-AD)
0ns(min.)
ADi BHE
td(BCLK-ALE) 25ns(max.)
th(BCLK-ALE)
-4ns(min.)
ALE td(BCLK-WR)
30ns(max.)
WR, WRL, WRH td(BCLK-DB) 40ns(max.) DBi Hi-Z td(DB-WR) (0.5 tcyc -40)ns(min.) tcyc = 1 f(BCLK) th(WR-DB) (0.5 tcyc -10)ns(min.) th(BCLK-DB)
0ns(min.)
Measuring conditions VCC1 = V CC2 = 3 V Input timing voltage: V = 0.6 V, V = 2.4 V IL IH Output timing voltage: V = 1.5 V, V = 1.5 V OL OH
Figure 5.14
Timing Diagram
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 3 V 5.3.5 Switching Characteristics (Memory Expansion Mode and Microprocessor Mode (in 1 to 3 Waits Setting and When Accessing External Area))
(VCC1 = VCC2 = 3 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
Table 5.51 Memory Expansion Mode and Microprocessor Mode (in 1 to 3 Waits Setting and When Accessing External Area)
Parameter Address output delay time Address output hold time (in relation to BCLK) Address output hold time (in relation to RD) Address output hold time (in relation to WR) Chip select output delay time Chip select output hold time (in relation to BCLK) ALE signal output delay time ALE signal output hold time RD signal output delay time RD signal output hold time WR signal output delay time WR signal output hold time Data output delay time (in relation to BCLK) Data output hold time (in relation to BCLK) (3) Data output delay time (in relation to WR) Data output hold time (in relation to WR) (3) HLDA output delay time 0 (Note 1) (Note 2) 40 0 40 See
Figure 5.13
Symbol td(BCLK-AD) th(BCLK-AD) th(RD-AD) th(WR-AD) td(BCLK-CS) th(BCLK-CS) td(BCLK-ALE) th(BCLK-ALE) td(BCLK-RD) th(BCLK-RD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) th(BCLK-DB) td(DB-WR) th(WR-DB) td(BCLK-HLDA)
Measuring Condition
Unit ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns
f ( BCLK )
2.
f ( BCLK )
3.
This standard value shows the timing when the output is off, and does not show hold time of data bus. Hold time of data bus varies with capacitor volume and pullup (pull-down) resistance value. Hold time of data bus is expressed in t=CR ln(1VOL/VCC2) by a circuit of the right figure. For example, when VOL = 0.2VCC2, C = 30 pF, R = 1 k, hold time of output low level is t = 30 pF 1 k In(1 0.2VCC2/VCC2) = 6.7 ns.
R DBi C
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 3 V
th(BCLK-CS)
0ns(min.)
CSi tcyc
td(BCLK-AD)
30ns(max.)
th(BCLK-AD)
0ns(min.)
ADi BHE
td(BCLK-ALE)
25ns(max.)
th(BCLK-ALE)
-4ns(min.)
th(RD-AD)
0ns(min.)
ALE td(BCLK-RD)
30ns(max.)
th(BCLK-RD)
0ns(min.) {(n+0.5) t cyc-60}ns(max.)
RD
tac2(RD-DB)
DBi
Hi-Z
tsu(DB-RD)
50ns(min.)
Write timing
BCLK td(BCLK-CS)
30ns(max.)
th(BCLK-CS)
0ns(min.)
CSi tcyc
td(BCLK-AD)
30ns(max.)
th(BCLK-AD)
0ns(min.)
ADi BHE
td(BCLK-ALE)
25ns(max.)
th(BCLK-ALE)
-4ns(min.)
th(WR-AD)
(0.5 tcyc -10)ns(min.)
ALE td(BCLK-WR)
30ns(max.)
th(BCLK-WR)
0ns(min.)
td(BCLK-DB)
40ns(max.)
th(BCLK-DB)
0ns(min.)
th(WR-DB)
tcyc =
Measuring conditions VCC1 = V CC2 = 3 V Input timing voltage: V = 0.6 V, V = 2.4 V IL IH Output timing voltage: V = 1.5 V, V = 1.5 V OL OH
Figure 5.15
Timing Diagram
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 3 V 5.3.6 Switching Characteristics (Memory Expansion Mode and Microprocessor Mode (in 2 or 3 Waits Setting, and When Accessing External Area and Using Multiplexed Bus))
(VCC1 = VCC2 = 3 V, VSS = 0 V, at Topr = -20 to 85C/-40 to 85C unless otherwise specified)
Table 5.52 Memory Expansion Mode and Microprocessor Mode (in 2 or 3 Waits Setting, and When Accessing External Area and Using Multiplexed Bus) (5)
Parameter Address output delay time Address output hold time (in relation to BCLK) Address output hold time (in relation to RD) Address output hold time (in relation to WR) Chip select output delay time Chip select output hold time (in relation to BCLK) Chip select output hold time (in relation to RD) Chip select output hold time (in relation to WR) RD signal output delay time RD signal output hold time WR signal output delay time WR signal output hold time Data output delay time (in relation to BCLK) Data output hold time (in relation to BCLK) Data output delay time (in relation to WR) Data output hold time (in relation to WR)
HLDA output delay time
Symbol td(BCLK-AD) th(BCLK-AD) th(RD-AD) th(WR-AD) td(BCLK-CS) th(BCLK-CS) th(RD-CS) th(WR-CS) td(BCLK-RD) th(BCLK-RD) td(BCLK-WR) th(BCLK-WR) td(BCLK-DB) th(BCLK-DB) td(DB-WR) th(WR-DB)
td(BCLK-HLDA)
Measuring Condition
Unit ns ns ns ns ns ns ns ns ns ns ns ns
See
Figure 5.13
0 50 0 (Note 2) (Note 1) 40 25
ns ns ns ns ns ns ns ns ns ns ns
ALE signal output delay time (in relation to BCLK) ALE signal output hold time (in relation to BCLK) ALE signal output delay time (in relation to Address) ALE signal output hold time (in relation to Address) RD signal output delay from the end of address WR signal output delay from the end of address Address output floating start time
4
(Note 3) (Note 4) 0 0 8
ns
f ( BCLK )
2.
3.
Calculated according to the BCLK frequency as follows: 9 ( n 0.5 ) x10 n is 2 for 2 waits setting, 3 for 3 waits setting. ----------------------------------- 50 [ ns ] f ( BCLK ) Calculated according to the BCLK frequency as follows: 9 0.5x10 --------------------- 40 [ ns ] -
f ( BCLK )
4.
f ( BCLK )
5.
M16C/64A Group
5. Electrical Characteristics
VCC1 = VCC2 = 3 V
(in 2 or 3 waits setting, and when accessing external area and using multiplexed bus )
BCLK
td(BCLK-CS)
50ns(max.)
CSi td(AD-ALE) (0.5 tcyc -40ns(min.) ADi /DBi th(ALE-AD) (0.5 tcyc -15ns(min.) tdz(RD-AD)
8ns(max.)
Address
Data input
Address
th(RD-DB)
0ns(min.)
td(BCLK-AD)
50ns(max.)
td(AD-RD)
0ns(min.)
th(BCLK-AD)
0ns(min.)
ADi BHE
td(BCLK-ALE) 25ns(max.)
th(BCLK-ALE)
-4ns(min.)
ALE
RD
Write timing
BCLK td(BCLK-CS)
50ns(max.)
tcyc
th(BCLK-CS)
0ns(min.)
CSi td(BCLK-DB)
50ns(max.)
th(BCLK-DB)
0ns(min.)
ADi /DBi
Address
Data output
Address
ADi BHE
td(BCLK-ALE) 25ns(max.)
th(BCLK-ALE)
-4ns(min.)
td(AD-WR)
0ns(min.)
tcyc =
Measuring conditions VCC1 = V CC2 = 3 V Input timing voltage: V = 0.6 V, V = 2.4 V IL IH Output timing voltage: V = 1.5 V, V = 1.5 V OL OH
Figure 5.16
Timing Diagram
M16C/64A Group
HD *1 80
D 51
81
50 NOTE) 1. DIMENSIONS "*1" AND "*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION "*3" DOES NOT INCLUDE TRIM OFFSET.
*2
HE
ZE
100
31
ZD
Index mark
30 F
c
A2
L e y *3 bp x Detail F
D E A2 HD HE A A1 bp c e x y ZD ZE L
Min Nom Max 19.8 20.0 20.2 13.8 14.0 14.2 2.8 22.5 22.8 23.1 16.5 16.8 17.1 3.05 0.1 0.2 0 0.25 0.3 0.4 0.13 0.15 0.2 10 0 0.65 0.13 0.10 0.575 0.825 0.4 0.6 0.8
A1
M16C/64A Group
MASS[Typ.] 0.6g
HD *1 D
75
51 NOTE) 1. DIMENSIONS "*1" AND "*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION "*3" DOES NOT INCLUDE TRIM OFFSET.
76
50
bp b1 HE E
Reference Dimension in Millimeters Symbol
*2
c1
1 Index mark ZD
25 F
ZE
100
26
A2
D E A2 HD HE A A1 bp b1 c c1
c
A1
y e
*3
bp
L L1 Detail F
e x y ZD ZE L L1
Min Nom Max 13.9 14.0 14.1 13.9 14.0 14.1 1.4 15.8 16.0 16.2 15.8 16.0 16.2 1.7 0.05 0.1 0.15 0.15 0.20 0.25 0.18 0.09 0.145 0.20 0.125 0 8 0.5 0.08 0.08 1.0 1.0 0.35 0.5 0.65 1.0
REVISION HISTORY
Rev. 1.01 Date Feb 03, 2009 Page -
All trademarks and registered trademarks are the property of their respective owners. IEBus is a registered trademark of NEC Electronics Corporation. HDMI and High-Definition Multimedia Interface are registered trademarks of HDMI Licensing, LLC.
A- 1
Notes: 1. This document is provided for reference purposes only so that Renesas customers may select the appropriate Renesas products for their use. Renesas neither makes warranties or representations with respect to the accuracy or completeness of the information contained in this document nor grants any license to any intellectual property rights or any other rights of Renesas or any third party with respect to the information in this document. 2. Renesas shall have no liability for damages or infringement of any intellectual property or other rights arising out of the use of any information in this document, including, but not limited to, product data, diagrams, charts, programs, algorithms, and application circuit examples. 3. You should not use the products or the technology described in this document for the purpose of military applications such as the development of weapons of mass destruction or for the purpose of any other military use. When exporting the products or technology described herein, you should follow the applicable export control laws and regulations, and procedures required by such laws and regulations. 4. All information included in this document such as product data, diagrams, charts, programs, algorithms, and application circuit examples, is current as of the date this document is issued. Such information, however, is subject to change without any prior notice. Before purchasing or using any Renesas products listed in this document, please confirm the latest product information with a Renesas sales office. Also, please pay regular and careful attention to additional and different information to be disclosed by Renesas such as that disclosed through our website. (http://www.renesas.com ) 5. Renesas has used reasonable care in compiling the information included in this document, but Renesas assumes no liability whatsoever for any damages incurred as a result of errors or omissions in the information included in this document. 6. When using or otherwise relying on the information in this document, you should evaluate the information in light of the total system before deciding about the applicability of such information to the intended application. Renesas makes no representations, warranties or guaranties regarding the suitability of its products for any particular application and specifically disclaims any liability arising out of the application and use of the information in this document or Renesas products. 7. With the exception of products specified by Renesas as suitable for automobile applications, Renesas products are not designed, manufactured or tested for applications or otherwise in systems the failure or malfunction of which may cause a direct threat to human life or create a risk of human injury or which require especially high quality and reliability such as safety systems, or equipment or systems for transportation and traffic, healthcare, combustion control, aerospace and aeronautics, nuclear power, or undersea communication transmission. If you are considering the use of our products for such purposes, please contact a Renesas sales office beforehand. Renesas shall have no liability for damages arising out of the uses set forth above. 8. Notwithstanding the preceding paragraph, you should not use Renesas products for the purposes listed below: (1) artificial life support devices or systems (2) surgical implantations (3) healthcare intervention (e.g., excision, administration of medication, etc.) (4) any other purposes that pose a direct threat to human life Renesas shall have no liability for damages arising out of the uses set forth in the above and purchasers who elect to use Renesas products in any of the foregoing applications shall indemnify and hold harmless Renesas Technology Corp., its affiliated companies and their officers, directors, and employees against any and all damages arising out of such applications. 9. You should use the products described herein within the range specified by Renesas, especially with respect to the maximum rating, operating supply voltage range, movement power voltage range, heat radiation characteristics, installation and other product characteristics. Renesas shall have no liability for malfunctions or damages arising out of the use of Renesas products beyond such specified ranges. 10. Although Renesas endeavors to improve the quality and reliability of its products, IC products have specific characteristics such as the occurrence of failure at a certain rate and malfunctions under certain use conditions. Please be sure to implement safety measures to guard against the possibility of physical injury, and injury or damage caused by fire in the event of the failure of a Renesas product, such as safety design for hardware and software including but not limited to redundancy, fire control and malfunction prevention, appropriate treatment for aging degradation or any other applicable measures. Among others, since the evaluation of microcomputer software alone is very difficult, please evaluate the safety of the final products or system manufactured by you. 11. In case Renesas products listed in this document are detached from the products to which the Renesas products are attached or affixed, the risk of accident such as swallowing by infants and small children is very high. You should implement safety measures so that Renesas products may not be easily detached from your products. Renesas shall have no liability for damages arising out of such detachment. 12. This document may not be reproduced or duplicated, in any form, in whole or in part, without prior written approval from Renesas. 13. Please contact a Renesas sales office if you have any questions regarding the information contained in this document, Renesas semiconductor products, or if you have any other inquiries.
http://www.renesas.com
Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jln Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510