Cement - Lec-4

Lecture No.
04
Subject: Properties of Cement
Prepared by Dr. Salah Al-Dulaijan
Objectives of Lecture
To explain briefly the properties of Portland cement. The quality of a Portland cement is assessed in terms of different physical properties determined through the laboratory tests on the cement samples collected in accordance with ASTM C 183.
1. Fineness
95% of cement particles are smaller than 45 micrometer, with the average particle around 15 micrometer. Fineness of cement affects heat released and the rate of hydration. More is the fineness of cement more will be the rate of hydration.
Thus the fineness accelerates strength development principally during the first seven days.
Continue on Fineness
Fineness tests indirectly measures the surface area of the cement particles per unit mass :
Wagner turbidimeter test
(ASTM C 115)
Blaine air-permeability test
(ASTM C 204)
Sieving using No. 325 (45 m) sieve (ASTM C 430)
Fineness Testing
On left, Blaine test apparatus.
On right, Wagner turbidmeter
Particle size distribution of Portland Cement
2. Soundness
Soundness is the ability of a hardened paste to retain its volume after setting. A cement is said to be unsound (i.e. having lack of soundness) if it is subjected to delayed destructive expansion. Unsoundness of cement is due to presence of excessive amount of hard-burned free lime or magnesia
Cont. on Soundness
Unsoundness of a cement is determined by the following tests: Le-Chatelier accelerated test (BS 4550: Part 3) Autoclave-expansion test (ASTM C 151)
Autoclave-expansion test
(ASTM C 151)
3. Consistency
Consistency refers to the relative mobility of a freshly mixed cement paste or mortar or its ability to flow.
Normal or Standard consistency of cement is determined using the Vicats Apparatus. It is defined as that percentage of water added to form the paste which allows a penetration of 10 1 mm of the Vicat plunger.
Vicat Plunger Consistency Test
Consistency Test for mortar using the flow table
4. Setting Time
This is the term used to describe the stiffening of the cement paste. Setting time is to determine if a cement sets according to the time limits specified in ASTM C 150.
Setting time is determined using either the Vicat apparatus (ASTM C 191) or a Gillmore needle (ASTM C 266).
Initial setting time is the time from the instant at which water is added to the cement until the paste ceases to be fluid and plastic which corresponds to the time at which the Vicats initial set needle penetrate to a point 5 mm from the bottom of a special mould.
Cont. on Setting Time

ASTM C 150 prescribes a minimum initial setting time of 60 minutes for Portland cements. Final setting time the time required for the paste to acquire certain degree of hardness. This corresponds to the time at which the Viacts final set needle makes an impression on the paste surface but the cutting edge fails to do so. ASTM C 150 prescribes a maximum final setting time of 10 hours for Portland cements. Gypsum in the cement regulates setting time. Setting time is also affected by cement fineness, w/c ratio, and admixtures.
Vicat Needle
Time of Set for Portland Cements
5. Early Stiffening (False Set and Flash Set)

Early stiffening is the early development of stiffening in the working plasticity of cement paste, mortar or concrete. This includes both false set and flash set.
False Set
False set is evidenced by a significant loss of plasticity, i.e. stiffening, without the evolution of much heat shortly after mixing. Stiffening caused by rapid crystallization of interlocking needle-like secondary gypsum. False set cause no difficulty in placing and handling of concrete if the concrete is mixed for a longer time than usual or if it is remixed without additional water before it is transported or placed.
Flash Set (quick set)

Evidence by a quick and early loss of workability and it is usually accompanied by evolution of considerable heat from the hydration of aluminates. The workability can not be regained without the addition of water.
6. Compressive Strength
Compressive strength of cement is the most important property.
It is determined by ducting compression tests on standard 50 mm mortar cubes in accordance with ASTM C 109. In general, cement strength (based on mortar-cube tests) can not be used to predict concrete compressive strength with great degree of accuracy because of many variables in aggregate characteristics, concrete mixtures, construction procedures, and environmental conditions in the field. Rates of compressive strength development for concrete, made with various types of cement, are shown in Fig. 2-42.
Compressive Strength Test
Strength Development of Portland Cement mortar cubes
7. Heat of Hydration
It is the quantity of heat (in joules) per gram of unhydrated cement evolved upon complete hydration at a given temperature. The heat of hydration can be determined by ASTM C 186 or by a conduction calorimeter. The temperature at which hydration occurs greatly affects the rate of heat development.
Fineness of cement also affects the rate of heat development but not the total amount of heat librated.
Heat of Hydration determined by ASTM C 186 (left) or by a conduction calorimeter (right).
Cont. on Heat of Hydration

The amount of heat generated depends upon the chemical composition of cement. Following are the heat of hydration generated on hydration of the four compounds of cement. Compound Heat of hydration Remarks C3S 502 j/g--C2S 260 j/gMinimumC3A 867 j/g MaximumC4AF 419 j/g--C3S and C3A are the compounds responsible for the high heat evolution.
The approximate amount of heat generated using ASTM C 186, during the first 7 days (based on limited data) are as follows:
Type
Name
I II III
Normal Moderate High early strength Low heat of hydration Sulfate resistant
Heat of hydration (kj/kg) 349 263 370
IV
V
233
310
Cont. on Heat of Hydration

Cements do not generate heat at constant rate as illustrated in Figure 2-45 for a typical type I Portland cement
Stage 1:heat of wetting or initial hydrolysis C3A and C3S Hydration. 7 min after mixing. Stage 2: dormant period related to initial set. Stage 3. accelerated reaction of the hydration products. That determine the rate of hardening and final set.
Stage 4: decelerates formation of hydration products and determines the rate of early strength gain.
Stage 5: is a slow, steady formation of hydration products.
8. Loss on Ignition (LOI)

The test for loss on ignition is performed in accordance with ASTM C 114. A high weight loss on ignition of a cement sample (between 900 to 1000C) is an indication of pre-hydration and carbonation, which may be caused by:
Improper and prolonged storage Adulteration during transport and transfer
Loss on ignition values range between 0 to 3%
Loss on Ignition Test of cement
9. Density and Specific Gravity (ASTM C 188)

Density is the mass of a unit volume of the solids or particles, excluding air between particles. The particle density of Portland cement ranges from 3.10 to 3.25 Mg/m3, averaging 3.15 Mg/ m3.
It is used in concrete mixture proportioning calculations. For mixture proportioning, it may be more useful to express the density as relative density (specific gravity). On an average the specific gravity of cement is 3.15.
Storage of Cement
Cement is moisture-sensitive material; if kept dry it will retain its quality indefinitely. When exposed to moisture, cement will set more slowly and will have less strength compared to cement that kept dray.
At the time of use cement should be freeflowing and free of lumps.
Storage of Cement

Cement - Lec-4

Uploaded by

Copyright:

Available Formats

Cement - Lec-4

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Cement - Lec-4

Uploaded by

Copyright:

Available Formats

Lecture No.

On right, Wagner turbidmeter

Particle size distribution of Portland Cement

Vicat Plunger Consistency Test

Consistency Test for mortar using the flow table

Cont. on Setting Time

Time of Set for Portland Cements

5. Early Stiffening (False Set and Flash Set)

Flash Set (quick set)

Compressive Strength Test

Strength Development of Portland Cement mortar cubes

Heat of Hydration determined by ASTM C 186 (left) or by a conduction calorimeter (right).

Cont. on Heat of Hydration

Heat of hydration (kj/kg) 349 263 370

Cont. on Heat of Hydration

8. Loss on Ignition (LOI)

Loss on ignition values range between 0 to 3%

Loss on Ignition Test of cement

9. Density and Specific Gravity (ASTM C 188)

At the time of use cement should be freeflowing and free of lumps.

You might also like