Waveguide

PH0101 Unit 2 Lecture 4
Wave guide
Basic features
Rectangular Wave guide
Circular Wave guide
Applications
PH0101 Unit 2
Waveguides
Introduction
At frequencies higher than 3 GHz, transmission of
electromagnetic energy along the transmission
lines and cables becomes difficult.
This is due to the losses that occur both in the
solid dielectric needed to support the conductor
and in the conductors themselves.
A metallic tube can be used to transmit
electromagnetic wave at the above frequencies
PH0101 Unit 2
Definition
A Hollow metallic tube
of uniform cross section
for transmitting
electromagnetic waves
by successive
reflections from the inner
walls of the tube is
called waveguide.
PH0101 Unit 2
Basic features
Waveguides may be used to carry energy between pieces
of equipment or over longer distances to carry transmitter
power to an antenna or microwave signals from an antenna
to a receiver
Waveguides are made from copper, aluminum or brass.
These metals are extruded into long rectangular or circular
pipes.
An electromagnetic energy to be carried by a waveguide is
injected into one end of the waveguide.
The electric and magnetic fields associated with the signal
bounce off the inside walls back and forth as it progresses
down the waveguide.
PH0101 Unit 2 L
4
EM field configuration within the

waveguide
In order to determine the EM field configuration
within the waveguide, Maxwells equations
should be solved subject to appropriate boundary
conditions at the walls of the guide.
Such solutions give rise to a number of field
configurations. Each configuration is known as a
mode. The following are the different modes
possible in a waveguide system
PH0101 Unit 2
Components of Electric and Magnetic

Field Intensities in an EM wave
E y, H y
z ,
PH0101 Unit 2
Possible Types of modes

1. Transverse Electro Magnetic (TEM) wave:
Here both electric and magnetic fields are directed
components. (i.e.) E z = 0 and Hz = 0
2. Transverse Electric (TE) wave: Here only the
electric field is purely transverse to the direction of

propagation and the magnetic field is not purely
transverse. (i.e.) E z = 0, Hz 0
PH0101 Unit 2
Possible Types of modes

3. Transverse Magnetic (TM) wave: Here only
magnetic field is transverse to the direction
of propagation and the electric field is not purely
transverse. (i.e.) E z 0, Hz = 0.
4. Hybrid (HE) wave: Here neither electric nor
magnetic fields are purely transverse to the
direction of propagation. (i.e.) E z 0, Hz 0.
PH0101 Unit 2
PH0101 Unit 2
Rectangular Waveguides
Any shape of cross section of a waveguide
can support electromagnetic waves of
which rectangular and circular waveguides
have become more common.
A waveguide having rectangular cross
section is known as Rectangular waveguide
PH0101 Unit 2
10
Rectangular waveguide
Dimensions of the waveguide which determines

the operating frequency range
PH0101 Unit 2
11
Dimensions of the waveguide which determines the

operating frequency range:
1. The size of the waveguide determines its operating

frequency range.
2. The frequency of operation is determined by the
dimension a.
3. This dimension is usually made equal to one half
the wavelength at the lowest frequency of operation,
this frequency is known as the waveguide cutoff
frequency.
4. At the cutoff frequency and below, the waveguide will
not transmit energy. At frequencies above the cutoff
frequency, the waveguide will propagate energy.
PH0101 Unit 2
12
Wave paths in a waveguide at various

frequencies
Angle of incidence(A)
Angle of reflection (B)

(A = B)
(a)At high
frequency
(b) At medium
frequency
( c ) At low
frequency
(d) At cutoff
frequency
PH0101 Unit 2
13
Wave propagation
When a probe launches energy into the
waveguide, the electromagnetic fields bounce
off the side walls of the waveguide as shown in
the above diagram.
The angles of incidence and reflection depend
upon the operating frequency. At high
frequencies, the angles are large and therefore,
the path between the opposite walls is relatively
long as shown in Fig.
PH0101 Unit 2
14
At lower frequency, the angles decrease and the

path between the sides shortens.
When the operating frequency is reaches the
cutoff frequency of the waveguide, the signal simply
bounces back and forth directly between the side
walls of the waveguide and has no forward motion.
At cut off frequency and below, no energy will
propagate.
PH0101 Unit 2
15
Cut off frequency

The exact size of the wave guide is selected
based on the desired operating frequency.
The size of the waveguide is chosen so that
its rectangular width is greater than one half
the wavelength but less than the one
wavelength at the operating frequency.
This gives a cutoff frequency that is below the
operating frequency, thereby ensuring that
the signal will be propagated down the line.
PH0101 Unit 2
16
Representation of modes
The general symbol of representation will be TE m, n
or TM m, n where the subscript m indicates the
number of half wave variations of the electric field
intensity along the b ( wide) dimension of the
waveguide.
The second subscript n indicates the number of half
wave variations of the electric field in the a (narrow)
dimension of the guide.
The TE 1, 0 mode has the longest operating
wavelength and is designated as the dominant
mode. It is the mode for the lowest frequency that
can be propagated in a waveguide.
PH0101 Unit 2
17
Expression for cut off wavelength

For a standard rectangular waveguide, the cutoff
wavelength is given by,
2
m
Where a and b are measured in centimeters
PH0101 Unit 2
18
Circular wave guide

A Hollow metallic tube
of uniform circular
cross section for
transmitting
electromagnetic waves
by successive
reflections from the
inner walls of the tube
is called Circular
waveguide.
PH0101 Unit 2
19
Circular wave guide

The circular waveguide is used in many special
applications in microwave techniques.
It has the advantage of greater power handling
capacity and lower attenuation for a given cutoff
wavelength. However, the disadvantage of
somewhat greater size and weight.
The polarization of the transmitted wave can be
altered due to the minor irregularities of the wall
surface of the circular guide, whereas the
rectangular wave guide the polarization is fixed
PH0101 Unit 2
20
PH0101 Unit 2
21
Description
The wave of lowest frequency or the dominant
mode in the circular waveguide is the TE11 mode.
The first subscript m indicates the number of full
wave variations of the radial component of the
electric field around the circumference of the
waveguide.
The second subscript n indicates the number of
half wave variations across the diameter.
The field configurations of TE11 mode in the
circular waveguide is shown in the diagram below
PH0101 Unit 2
22
Cut off wavelength

The cutoff wavelength for dominant mode of
propagation TE11 in circular waveguide of radius a
is given by
2 a
c
1.814
The cutoff wavelength for dominant mode of
propagation TM01 in circular waveguide of radius a
is given by
2 a
2.405
PH0101 Unit 2
23
Applications of circular waveguide

Rotating joints in radars to connect the horn
antenna feeding a parabolic reflector (which
must rotate for tracking)
TE01 mode suitable for long distance waveguide
transmission above 10 GHz.
Short and medium distance broad band
communication (could replace / share coaxial
and microwave links)
PH0101 Unit 2
24
Worked Example 2.4

The dimensions of the waveguide are 2.5 cm 1 cm.
The frequency is 8.6 GHz. Find (i) possible modes
and (ii) cut off frequency for TE waves.
Solution:
Given a = 2.5 cm , b = 1 cm and f = 8.6 GHz
Free space wavelength
10
C
3 10
0
3.488 cm
9
f
8 10
PH0101 Unit 2
25
Solution
The condition for the wave to propagate is that
C > 0
For TE01 mode
2ab
m 2b 2 n 2 a 2
2ab
a2
2b 2 1 2 cm
Since C < 0, TE01 does not propagate

PH0101 Unit 2
26
For TE10 mode, C = 2a = 2 2.5 = 5 cm

Since C > 0 , TE10 mode is a possible mode.
Cut off frequency = f C
Cut-off wavelength
for TE11 mode
3 1010
6 GHz
5
2 ab
a2 b2
2 2 .5 1
( 2.5) (1)
2
For TE11 C < 0 , TE11 is not possible.

The possible mode is TE10 mode.
The cut off frequency = 6 GHz
PH0101 Unit 2 L
1.856 cm
27
Worked Example 2.5
For the dominant mode propagated in an air filled circular

waveguide, the cut off wavelength is 10 cm. Find (i) the
required size or cross sectional area of the guide and (ii) the
frequencies that can be used for this mode of propagation
The cut off wavelength = C = 10 cm
The radius of the circular waveguide ,
r =
10 1.841
2.93 cm
2
PH0101 Unit 2
28
Solution
Area of cross section =
r (2.93) 26.97 cm
2
The cut off frequency

=
3 10
fc
c
10
C
10
= 3 GHz
Therefore the frequency above 3 GHz can be

propagated through the waveguide.
Area of cross section = 26.97 cm2
Cut off frequency = 3 GHz
PH0101 Unit 2
29
Exercise Problem 2.2

A rectangular waveguide has a = 4 cm and b = 3 cm as
its sectional dimensions. Find all the modes which will
propagate at 5000 MHz.
Hint:
The condition for the wave to propagate is that C > 0
Here 0 = 6 cm ; C for TE01 mode = 6 cm
Hence C is not greater than free space wavelength 0 .
TE01 mode is not possible.
PH0101 Unit 2
30
Exercise problem 2.3

For the dominant mode of operation is an air filled
circular waveguide of inner diameter 4 cm. Find (i)
cut off wavelength and (ii) cut off frequency.
Hint: C = 6.8148 cm and fc = 4.395 GHz
PH0101 Unit 2
31
PH0101 Unit 2
32

Waveguide

Uploaded by

Copyright:

Available Formats

Waveguide

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Waveguide

Uploaded by

Copyright:

Available Formats

What are the different types of modes in a waveguide?

What are the different types of modes in a waveguide?

How does an electromagnetic wave propagate through a waveguide?

How does an electromagnetic wave propagate through a waveguide?

PH0101 Unit 2 Lecture 4

EM field configuration within the

Components of Electric and Magnetic

Possible Types of modes

electric field is purely transverse to the direction of

Possible Types of modes

Dimensions of the waveguide which determines

Dimensions of the waveguide which determines the

1. The size of the waveguide determines its operating

Wave paths in a waveguide at various

Angle of reflection (B)

At lower frequency, the angles decrease and the

Cut off frequency

Expression for cut off wavelength

Where a and b are measured in centimeters

Circular wave guide

Circular wave guide

Cut off wavelength

Applications of circular waveguide

Worked Example 2.4

Since C < 0, TE01 does not propagate

For TE10 mode, C = 2a = 2 2.5 = 5 cm

For TE11 C < 0 , TE11 is not possible.

Worked Example 2.5

For the dominant mode propagated in an air filled circular

The cut off frequency

Therefore the frequency above 3 GHz can be

Exercise Problem 2.2

Exercise problem 2.3

You might also like