Lesson 1 AQS

LESSON 1:
APPLYING QUALITY STANDARDS

(AQS)
ASSESS QUALITY OF RECEIVED MATERIALS
Obtain work instruction in accordance with standard
operating procedures
Check the received materials against workplace
standards and specifications
Identify and isolate faulty materials related to work
ASSESS QUALITY OF RECEIVED MATERIALS
Record and/ or report defects and any
identified causes to the supervisor concerned in
accordance with workplace procedures
Replace faulty materials in accordance with
workplace procedures
CONTENT:
WORK ORDER AND STANDARD

OPERATING PROCEDURES
WORK ORDER
an order received by an organization from

a customer or client, or an order created
internally within the organization.
A work order may be for products or

services.
STANDARD OPERATING PROCEDURES
is a set of step-by-step instructions compiled by

an organization to help workers carry out routine
operations.
SOPs aim to achieve efficiency, quality output and
uniformity of performance, while
reducing miscommunication and failure to comply
with industry regulations.
INFORMATION SHEET 1.1:
SPECIFICATION OF MATERIALS AND

COMPONENTS
FACTORS THAT MUST BE TAKEN INTO CONSIDERATION WHEN
CHOOSING THE RIGHT MATERIAL FOR THEIR COMPONENTS AND
ASSEMBLIES
1. Selection of materials
The ability to assess the materials impact on the
performance of a product is crucial for reliable
performance.
Considering the label or name of the company which

are producing great quality of materials and are
known in the market.
ASSEMBLIES
2. Testing of materials
The testing of material properties is widely
understood to be the key to obtaining data
for a project, performing failure analysis, or
understanding material interactions.
ASSEMBLIES
3. Cost of Materials
The amount may vary but never
taken for granted the quality and
the reliability of the material.
CONTENT:
CHARACTERISTICS OF THE MATERIALS

Good Quality
This is the most important factor when choosing
materials to buy.
Products with good quality are long-lasting and

safe to use because you know that it follows
certain standards before being commercialized.
Reliable
It means that you can be sure that it will
perform its function well, will operate safely
and will give the best it could give.
Suitable for the application/purposes

Choose the materials which are very necessary to
make the project possible.
Making a list of products/materials to buy is a
good trait of a wise consumer.
Products which are not to be used must be crossed
out.
Low cost
It doesnt mean that you will choose for the less
expensive one and exclude the quality.
Low cost means you can afford to buy the

materials without hurting your pocket and assure
of better quality.
SELF-CHECK 1.1
Enumerate the following. Use a separate sheet
of paper in answering.
Give three factors to be considered when choosing
the right material?
Give three characteristic of materials to be used for

specific project?
What Good Quality means?

INFORMATION SHEET 1.2:
FAULT IDENTIFICATION AND

RERORTING
THERE ARE THREE THINGS WHEN RECEIVING
WHEN:
A. Receiving Materials
1. Match the packing slip to the items received
and ensures that the materials are destined on
tour department.
2. That you are receiving the materials indicated
on the purchase order with regard to quantity
and discount.
WHEN:
A. Receiving Materials
3. That the materials are in acceptable condition.
4. That terms regarding installation and/or set-up
of equipment are met.
WHEN:
B. RECEIVING REPORTS
The person receiving the goods must document, using the
administrative software, that all goods were received for
each requisition before any payment can be made to the
vendor.
Any exceptions must be noted so that partial payments can

be processed or defective goods can be returned.
WHEN:
C. RETURN OF MERCHANDISE
When merchandise is received which is incomplete
or defective, return the materials to the supplier or
to the store where it was bought and make
arrangements with the vendor for replacement.
WHEN:
D. Make an Inventory Report of the Materials

All materials received must be listed and be reported
to monitor how many materials are already on hand,
purchased or damaged.
EXAMPLE OF LOG REPORT
Date Quality
O.R. # Item Name Quantity Signature
Received Checker
EXAMPLE OF ASSESSMENT OF MATERIALS
RECEIVED
Quality Checker: Date:
Total no. in Total no.

Item Name Comments
Good Condition of Errors
TASK SHEET 1.2
You are assigned to be the Quality checker for the Month of June.
Make a Log Report, and Assessment Report using the following data
below. Make sure you will record all the items listed and if they
were in good condition or not. Write your answer on a sheet of
paper.
June 9, 2008
5 Hard disk, 2 128MB SDRAM memory chips
Received from Jun Salcedo (PC chain), OR #20256
Found out that 1 Hard disk has error need for replacement
June 15, 2008

Refill ink cartridge from STARINK Shop, OR# 5623
June 20, 2008

10 PS/2 keyboard, 10 Optic mouse, 2 power supply
Received from Allan Rivera (Octagon), OR#12544
3 defective keyboard need replacement
June 28, 2008

2 CD-Rom drive
Received from Jun Salcedo (PC Chain), OR#20400
ASSIGNMENT
1. What is workplace procedure?

2. Give five examples of behavior that may affect the
quantity of work.
3. Give five examples of behavior that may affect the
quality of work.

Lesson 1 AQS

Uploaded by

Copyright:

Available Formats

Lesson 1 AQS

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Lesson 1 AQS

Uploaded by

Copyright:

Available Formats

LESSON 1:

APPLYING QUALITY STANDARDS

WORK ORDER AND STANDARD

an order received by an organization from

A work order may be for products or

is a set of step-by-step instructions compiled by

SPECIFICATION OF MATERIALS AND

Considering the label or name of the company which

CHARACTERISTICS OF THE MATERIALS

Products with good quality are long-lasting and

Suitable for the application/purposes

Low cost means you can afford to buy the

Give three characteristic of materials to be used for

What Good Quality means?

FAULT IDENTIFICATION AND

Any exceptions must be noted so that partial payments can

D. Make an Inventory Report of the Materials

Total no. in Total no.

June 15, 2008

June 20, 2008

June 28, 2008

1. What is workplace procedure?

You might also like