11 Magnetic Circuit

Magnetic Flux
Unit for flux is weber

The definition of 1 weber is the amount of flux
that can produce an induced voltage of 1 V in a one
turn coil if the flux reduce to zero with uniform rate.
Magnetic Flux density B
Unit for magnetic flux density is Tesla
The definition of 1 tesla is the flux density that
can produce a force of 1 Newton per meter acting
upon a conductor carrying 1 ampere of current.
Magnetic field strength H
Unit for magnetic field strength is Ampere/m
A line of force that produce flux
F = B l I newton
Where F = force ; B = magnetic flux density ; l =the length of

conductor and I = current in the conductor
B A
Where = magnetic flux ; B = magnetic flux density and A =
area of cross-section
B H
Where H = magnetic field strength ; B = magnetic flux density
and = permeability of the medium
Permeability in free space o = B/H = 4 x 10-7 H/m

Relative Permeability (r)
Relative permeability is defined as a ratio of flux density

produced in a material to the flux density produced in a
vacuum for the same magnetic filed strength. Thus
r = /o
= ro = B/H
or B = roH
H vs r
Mild steel
Cast iron
Relative
permeability
Magnetic field strength

Relative permeability vs magnetic flux
B vs H
Electromagnetic Force (mmf)
H
turns
mmf H NI
Where H = magnetic field strength ; l =the path length of ; N

number of turns and I = current in the conductor
Example 1
A coils of 200 turns is uniformly wound around a wooden ring
with a mean circumference of 600 mm and area of cross-section
of 500 mm2. If the current flowing into the coil is 4 A, Calculate
(a) the magnetic field strength , (b) flux density dan (c) total flux
turns
N = 200 turns
l = 600 x 10-3 m
A = 500 x 10-6 m2
I = 4A
(a) H = NI/l = 200 x 4 / 600 x 10-3 = 1333 A
(b) B = oH = 4 x 10-7 x 1333 = 0.001675 T = 1675 T
(c) Total Flux = BA = 1675 x 10-6 x 500 x 10-6
= 0.8375 Wb
Reluctance ( S )
Ohms law I = V/R [A]
Where I =current; V=voltage and R=resistance
And the resistance can be relate to physical parameters as
R = l /A ohm
Where =resistivity [ohm-meter], l= length in meter and A=area
of cross-section [meter square]
Analogy to the ohms law
V=NI=H l I= and R=S

weber
Hl
where S ampere / weber
S r o A
Example 2
A mild steel ring, having a cross-section area of 500 mm2 and a
mean circumference of 400 mm is wound uniformly by a coil
of 200 turns. Calculate(a) reluctance of the ring and (b) a
current required to produce a flux of 800 Wb in the ring.
(a)
800 106
B 6
1.6T turns
A 500 10
Dari graf r/B, pada B = 1.6;
r = 380
0.4
S
r o A 380 4 10 7 5 10 4
1.667 106 [ A / Wb]
(b)
H
H S
S
mmf H 800 106 1.667 106 1342[ A] NI
1342 1342
I 6.7[ A]
N 200
Magnetic circuit with different materials
l1 l2
SA and SB
1a1 2a 2
l1 l2
S SA S B
1a1 2a 2
For A: area of cross-section = a1

mean length = l1
absolute permeability = 1
ForB: area of cross-section = a2
mean length = l2
absolute permeability = 2
Mmf for many materials in series
total mmf = HAlA + HBlB
HA =magnetic strength in material A
lA=mean length of material A
HB =magnetic strength in material B
lB=mean length of material B
In general
(m.m.f) = Hl
Example 3
A magnetic circuit comprises three parts in series, each of
uniform cross-section area(c.s.a). They are :
(a)A length of 80mm and c.s.a 50 mm2;
(b)A length of 60mm and c.s.a 90mm2;
(c)An airgap of length 0.5mm and c.s.a 150 mm2.
A coil of 4000 turns is wound on part (b), and the flux density
in the airgap is 0.3T. Assuming that all the flux passes through
the given circuit, and that the relative permeability r is 1300,
estimate the coil current to produce such a flux density.
BC AC 0.3 1.5 10 4 0.45 10 4 Wb

Mmf = S = H l = N I
a 0.45 10 4 80 10 3
Material a S a 44.1At
r o Aa 1300 4 10 50 10
7 6
b 0.45 104 60 103

Material b S b 18.4 At
r o Ab 1300 4 10 90 10
7 6
airgap c 0.45 10 4 0.5 10 3

S c 119.3 At
r o Ac 1300 4 10 150 10
7 6
Total mmf NI Sa Sb Sc 44.1 18.4 119.3 181.8 At
and 181.8
I 45.4 10 3 A 45.4mA
4000
Leakages and fringing of flux
leakage
fringing
Magnetic circuit with air-gap Leakages and fringing of flux
Some fluxes are leakage via paths a, b and c . Path d is

shown to be expanded due to fringing. Thus the usable
flux is less than the total flux produced, hence
total flux
Leakage factor
usable flux
Example 4
A magnetic circuit as in Figure is made

from a laminated steel. The breadth of
the steel core is 40 mm and the depth is
50 mm, 8% of it is an insulator
between the laminatings. The length
and the area of the airgap are 2 mm and
2500 mm2 respectively. A coil is
wound 800 turns. If the leakage factor
is 1.2, calculate the current required to
magnetize the steel core in order to
produce flux of 0.0025 Wb across the
airgap.
2.5 103
Ba 6
1T
Aa 2500 10
Ba 1
Ha 796000[ AT / m]
o 4 10 7
mmf H 796000 0.002 1594[ AT ]
Total flux T flux in airgap leakage factor

0.00251.2 0.003Wb
92% of the depth is laminated steel, thus the area of cross
section is
AS = 40 x 50 x 0.92 = 1840 mm2=0.00184m

T 3 103
BS 1.63T
AS 0.00184
From the B-H graph, at B=1.63T, H=4000AT/m
mmf in the steel core = Hl = 4000 x 0.6 = 2400 AT
Total mmf. = 1592 + 2400 = 3992 AT
NI = 3992
I = 3992/800 = 5 A
D
Magnetic circuit applying voltage law Analogy to electrical circuit
applying voltage Kirchoffs law

Mmf in loop C = NI = HLlL + HMlM
outside loop NI= HLlL + HNlN
And in loop D 0 = HMlM + HNlN
In general (m.m.f) = Hl
P
IL IM IN
L M N
At node P we can also applying current Kirchoffs law
L = M + N
Or L - M - N = 0
In general: = 0
Example 5
A magnetic circuit made of silicon steel is arranged as in the
Figure. The center limb has a cross-section area of 800mm2 and
each of the side limbs has a cross-sectional area of 500mm2.
Calculate the m.m.f required to produce a flux of 1mWb in the
center limb, assuming the magnetic leakage to be negligible.
340 1mm 340

mm 150 mm
mm
110 3
B A B 6
1.25T
A 800 10
Looking at graph at B=1.25T r =34000
Apply voltage law in loops A and B 340

mm 150
1mm 340
mm
A mm B
m.m. f A S1 A B S2 Sa
1 340 103
S1 15915
r o A1 34000 4 107 500 106
150 10 3
S2 4388
34000 4 10 800 10
7 6
110 3
Sa 994718
4 10 800 10
7 6
Since the circuit is symmetry A =B
m.m. f S1 2 S2 Sa
In the center limb , the flux is 1mWb which is equal to 2

Therefore =0.5mWb

m.m. f 0.5 103 15915 1103 4388 994718
8 999 1007 A
Example 6
A U-shaped electromagnet shown in
Fig. is designed to lift a mass. The I
N
material for the yoke has a relative
permeability of 2900. The yoke has a Iron yoke
uniform cross-sectional area of 4000
mm2 and a mean length of 600 mm.
Each of the air gaps is 0.1 mm long. Keeper
The number of turns of the coil (N) is Air gap
240. Assuming that the reluctance of
the keeper is negligible, calculate the Weight
maximum mass in kg, which can be
lifted by the system if a current of 1.5 A
is passed through the coil. You may
neglect the fringing effect and flux
leakage; and assume that
Calculation of maximum weight lifted by and electromagnet.
Let the flux density in the air gap be Ba

Ba l a
For the air gap 2H a la 2
o
Ba 0.1 10 3
2
4 10 7
10 3
Ba
2
For the iron yoke
Ba li Ba 600 10 3 6 103
H i li Ba
r o 2900 4 10 7
11.6
Total mmf;
1 6 103
Hl H a la H i li Ba 323.8Ba NI
2 11.6
NI 360
Ba 1.11 T
323.8 323.8
Since there are two air gaps;

Ba 2 A Ba 2 A 1.112 4000 10 6
F 2
3922 N
2 o o 4 10 7
mg 3922
3922 3922
m 400 kg
g 9.81
Hysteresis loss
Materials before applying m.m.f (H), the polarity of

the molecules or structures are in random.
After applying m.m.f (H) , the polarity of the

molecules or structures are in one direction, thus the
materials become magnetized. The more H applied
the more magnetic flux (B )will be produced
When we plot the mmf (H) versus the magnetic flux will produce a
curve so called Hysteresis loop
1. OAC when more H applied, B

increased until saturated. At this
point no increment of B when we
increase the H.
2. CD- when we reduce the H the B
also reduce but will not go to zero.
3. DE- a negative value of H has to
applied in order to reduce B to zero.
4. EF when applying more H in the
negative direction will increase B in
the reverse direction.
5. FGC- when reduce H will reduce B
but it will not go to zero. Then by
increasing positively the also
decrease and certain point it again
change the polarity to negative until
it reach C.
Eddy current
When a sinusoidal current enter
the coil, the flux also varies
sinusoidally according to I. The
induced current will flow in the
magnetic core. This current is
called eddy current. This
current introduce the eddy
current loss. The losses due to
hysteresis and eddy-core totally
called core loss. To reduce eddy
current we use laminated core
metal insulator

11 Magnetic Circuit

Uploaded by

Copyright:

Available Formats

11 Magnetic Circuit

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

11 Magnetic Circuit

Uploaded by

Copyright:

Available Formats

Magnetic Flux

Unit for flux is weber

Where F = force ; B = magnetic flux density ; l =the length of

Permeability in free space o = B/H = 4 x 10-7 H/m

Relative permeability is defined as a ratio of flux density

Magnetic field strength

Where H = magnetic field strength ; l =the path length of ; N

mmf H 800 106 1.667 106 1342[ A] NI

For A: area of cross-section = a1

BC AC 0.3 1.5 10 4 0.45 10 4 Wb

b 0.45 104 60 103

airgap c 0.45 10 4 0.5 10 3

Total mmf NI Sa Sb Sc 44.1 18.4 119.3 181.8 At

Magnetic circuit with air-gap Leakages and fringing of flux

Some fluxes are leakage via paths a, b and c . Path d is

A magnetic circuit as in Figure is made

mmf H 796000 0.002 1594[ AT ]

Total flux T flux in airgap leakage factor

AS = 40 x 50 x 0.92 = 1840 mm2=0.00184m

From the B-H graph, at B=1.63T, H=4000AT/m

mmf in the steel core = Hl = 4000 x 0.6 = 2400 AT

Total mmf. = 1592 + 2400 = 3992 AT

Magnetic circuit applying voltage law Analogy to electrical circuit

applying voltage Kirchoffs law

At node P we can also applying current Kirchoffs law

340 1mm 340

Looking at graph at B=1.25T r =34000

Apply voltage law in loops A and B 340

In the center limb , the flux is 1mWb which is equal to 2

Let the flux density in the air gap be Ba

Since there are two air gaps;

Materials before applying m.m.f (H), the polarity of

After applying m.m.f (H) , the polarity of the

1. OAC when more H applied, B

You might also like